Note: See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing. Cutting post sleeves is NOT ...
Selecting the right railing is pretty easy, but. 1 4 1 2 each Trex railing line is a little different. Please. read the system descriptions at the top of each product section so you can choose exactly which...
RAILING
53
RAILING
2a
3a
RAILING--
a lot easier than it looks
Selecting the right railing is pretty easy, but
1
each Trex railing line is a little different. Please
4
1+2
read the system descriptions at the top of each
product section so you can choose exactly which
railing components you need to complete your
design. For additional guidance, the chart to the
3b
5
left depicts each railing system's components.
2b
333
TREX POST COMPONENTS TREX® SIGNATURETM RAILING
TREX TRANSCEND® RAILING
TREX SELECT® RAILING
Trex Post Sleeves, Caps & Skirts
These components can be used as Steps 1 & 2 for all Trex railing lines.
STEP
1
COMPONENT
Post Sleeve
Each 4x4 and 6x6 post sleeve fits over a 4x4 pressure treated post or equivalent post mount.
Post Sleeve Cap
2a
Also available with LED lighting. See page 52.
Post Sleeve Skirt
2b
ACCESSORY Surface Mount Post
(for use with 4x4 composite post sleeve)
DESCRIPTION
4" x 4" x 39" Post Sleeve
[4.45 in x 4.45 in x 40 in (113 mm x 113 mm x 101 cm) external dimensions]
4" x 4" x 108" Post Sleeve
[4.45 in x 4.45 in x 108 in (113 mm x 113 mm x 274 cm) external dimensions]
6" x 6" x 39" Post Sleeve
[5.5 in x 5.5 in x 39 in (139 mm x 139 mm x 990 mm) external dimensions]
6" x 6" x 108" Post Sleeve
[5.5 in x 5.5 in x 108 in (139 mm x 139 mm x 274 cm) external dimensions]
Flat 4" x 4" Post Sleeve Cap Pyramid 4" x 4" Post Sleeve Cap
[4.55 in x 4.55 in (115 mm x 115 mm) internal dimensions]
Flat 6" x 6" Post Sleeve Cap Pyramid 6" x 6" Post Sleeve Cap
[5.55 in x 5.55 in (140 mm x 140 mm) internal dimensions]
ITEM NUMBER
XX040439APS XX0404108APS
WT060639APS WT0606108APS
PXXSQCAP4X4 PXXPYCAP4X4 PWTSQCAP6X6 PWTPYCAP6X6
4" x 4" Post Sleeve Skirt
[4.55 in x 4.55 in (115 mm x 115 mm) internal dimensions]
6" x 6" Post Sleeve Skirt
[5.55 in x 5.55 in (140 mm x 140 mm) internal dimensions]
PXXSKIRT4X4 PWTSKIRT6X6
Aluminum Surface Mount Post for 36" (914 mm) Rail Height (1/box) ALPOSTMOUNT36
Actual external dimensions of insert: 3.75 in x 3.75 in x 7 in (95 mm x 95 mm x 177 mm)
Aluminum Surface Mount Post for 42" (1066 mm) Rail Height (1/box) ALPOSTMOUNT42
Actual external dimensions of insert: 3.75 in x 3.75 in x 7 in (95 mm x 95 mm x 177 mm)
Surface Mount Post Hardware--Wood (10 kits/box)
ALPOSTHWDECK
ACCESSORY Joist Mount Post
(for use with 4x4 composite post sleeve)
Aluminum Joist Mount Post for use with all Trex railing heights (1/box)
Actual external dimensions of insert: 3.75 in x 3.75 in x 7 in (95 mm x 95 mm x 177 mm)
CPJMNTPOST63
RAILING
ACCESSORY Foot Block
Adjustable Foot Blocks
WT Classic White
FP Fire Pit
XX = COLOR PREFIX:
54
BK Charcoal Black
GP Gravel Path
RS Rope Swing TH Tree House
XXFTBLKPC VL Vintage Lantern
Trex® SignatureTMAluminum Railing
Choose either aluminum posts or composite post sleeves, caps and skirts for Steps 1 & 2. Pair with a rail & baluster kit (Step 3).
STEP
COMPONENT
DESCRIPTION
ITEM NUMBER
1+2
Aluminum Post with Cap & Skirt
Aluminum Crossover Post
Signature aluminum posts fulfill Steps 1 & 2. If using composite post sleeves, refer to page 48.
Aluminum posts can only be used with the Signature line.
IRC Surface Mount Hardware
2.5" x 2.5" x 37" Post--Horizontal (IRC Compliant)
[2.5 in x 2.5 in x 37 in (63 mm x 63 mm x 939 mm) actual dimensions]
2.5" x 2.5" x 43" Post--Horizontal (IRC Compliant)
[2.5 in x 2.5 in x 43 in (63 mm x 63 mm x 109 cm) actual dimensions]
2.5" x 2.5" x 53" Post--Stair (IRC Compliant)
[2.5 in x 2.5 in x 53 in (63 mm x 63 mm x 134 cm) actual dimensions]
2.5" x 2.5" x 36" Crossover Post--Horizontal (IRC Compliant)
[2.5 in x 2.5 in x 36 in (63 mm x 63 mm x 914 mm) actual dimensions]
2.5" x 2.5" x 42" Crossover Post--Horizontal (IRC Compliant)
[2.5 in x 2.5 in x 42 in (63 mm x 63 mm x 106 cm) actual dimensions]
Aluminum Mounting Plate & Hardware
For use with all Trex 2.5" Surface Mount Aluminum Posts
Concrete Post Mount Kit
XXAL252537RCAP XXAL252543RCAP XXAL252553RCAP XXAL252536RCCP XXAL252542RCCP
ALPOSTHWDECK ALPOSTHWCONC
Aluminum Joist Mount Post with Cap & Skirt
Trex® SignatureTM Fascia Mount Kit
(for use with wood framing)
2.5" x 2.5" x 63"
[2.5 in x 2.5 in x 63 in (63 mm x 63 mm x 160 cm) actual dimensions]
XXJMNTPOST63
For use with Joist Mount Trex® SignatureTM Railing
Post only.
XXFMNTWOOD
STEP
DESCRIPTION
ITEM NUMBER
DESCRIPTION
ITEM NUMBER
Rail & Baluster Kit
3
(includes Top Rail, Bottom Rail, Balusters, Mounting & Support Hardware)
6' x 36" Rail Kit w. Square Balusters--Horizontal 6' x 36" Rail Kit w. Square Balusters--Stair 8' x 36" Rail Kit w. Square Balusters--Horizontal 8' x 36" Rail Kit w. Square Balusters--Stair
XXAS0636HRK XXAS0636SRK XXAS0836HRK XXAS0836SRK
Rail & Rod Kit
(includes Top Rail, Bottom Rail, Rods, Mounting & Support Hardware)
6' x 36" Black Frame & Platinum Rod Railing--Horizontal 6' x 36" Black Frame & Platinum Rod Railing--Stair 8' x 36" Black Frame & Platinum Rod Railing--Horizontal 8' x 36" Black Frame & Platinum Rod Railing--Stair
BKPLROD0636HRK BKPLROD0636SRK BKPLROD0836HRK BKPLROD0836SRK
6' x 42" Rail Kit w. Square Balusters--Horizontal 6' x 42" Rail Kit w. Square Balusters--Stair 8' x 42" Rail Kit w. Square Balusters--Horizontal 8' x 42" Rail Kit w. Square Balusters--Stair
XXAS0642HRK XXAS0642SRK XXAS0842HRK XXAS0842SRK
6' x 42" Black Frame & Platinum Rod Railing--Horizontal 6' x 42" Black Frame & Platinum Rod Railing--Stair 8' x 42" Black Frame & Platinum Rod Railing--Horizontal 8' x 42" Black Frame & Platinum Rod Railing--Stair
BKPLROD0642HRK BKPLROD0642SRK BKPLROD0842HRK BKPLROD0842SRK
6' x 36" Rail Kit w. Round Balusters--Horizontal 6' x 36" Rail Kit w. Round Balusters--Stair 8' x 36" Rail Kit w. Round Balusters--Horizontal 8' x 36" Rail Kit w. Round Balusters--Stair
XXAR0636HRK XXAR0636SRK XXAR0836HRK XXAR0836SRK
6' x 36" Bronze Frame & Platinum Rod Railing--Horizontal 6' x 36" Bronze Frame & Platinum Rod Railing--Stair 8' x 36" Bronze Frame & Platinum Rod Railing--Horizontal 8' x 36" Bronze Frame & Platinum Rod Railing--Stair
BZPLROD0636HRK BZPLROD0636SRK BZPLROD0836HRK BZPLROD0836SRK
6' x 42" Rail Kit w. Round Balusters--Horizontal 6' x 42" Rail Kit w. Round Balusters--Stair 8' x 42" Rail Kit w. Round Balusters--Horizontal 8' x 42" Rail Kit w. Round Balusters--Stair
XXAR0642HRK XXAR0642SRK XXAR0842HRK XXAR0842SRK
6' x 42" Bronze Frame & Platinum Rod Railing--Horizontal 6' x 42" Bronze Frame & Platinum Rod Railing--Stair 8' x 42" Bronze Frame & Platinum Rod Railing--Horizontal 8' x 42" Bronze Frame & Platinum Rod Railing--Stair
BZPLROD0642HRK BZPLROD0642SRK BZPLROD0842HRK BZPLROD0842SRK
6' x 36" Assembled Panel (Square)--Horizontal* 8' x 36" Assembled Panel (Square)--Horizontal* 6' x 42" Assembled Panel (Square)--Horizontal* 8' x 42" Assembled Panel (Square)--Horizontal*
*Does not include hardware
Dimensions above are actuals. See below for metrics. 6' Upper Rail = 73.5" (187cm) actual length 8' Upper Rail = 97.5" (248 cm) actual length 6' Lower Rail = 71.5" (182 cm) actual length 8' Lower Rail = 95.5" (243 cm) actual length
BKAS0636HRPNL BKAS0836HRPNL BKAS0642HRPNL BKAS0842HRPNL
6' x 36" Black Frame & Black Rod Railing--Horizontal 6' x 36" Black Frame & Black Rod Railing--Stair 8' x 36" Black Frame & Black Rod Railing--Horizontal 8' x 36" Black Frame & Black Rod Railing--Stair
6' x 42" Black Frame & Black Rod Railing--Horizontal 6' x 42" Black Frame & Black Rod Railing--Stair 8' x 42" Black Frame & Black Rod Railing--Horizontal 8' x 42" Black Frame & Black Rod Railing--Stair
BKBKROD0636HRK BKBKROD0636SRK BKBKROD0836HRK BKBKROD0836SRK
BKBKROD0642HRK BKBKROD0642SRK BKBKROD0842HRK BKBKROD0842SRK
ACCESSORY Trex®SignatureTMAccessories
Trex® SignatureTM Bracket Templates
HZ Bracket Template
SIGTEMP4X4SLEEVE
(36" and 42") - Composite Sleeve
HZ Bracket Template
SIGTEMPIRCPOST
(36" and 42") - 2.5" Aluminum Post
Cocktail Rail Bracket (10/pack) Fixed Bracket--Horizontal (4/pack) Fixed Bracket--Stair (4/pack) Swivel Bracket--Horizontal (2/pack1 top, 1 bottom) Swivel Bracket--Stair (2/pack1 top, 1 bottom) 2.5" Horizontal Crossover Bracket (1/pack) 2.5" Swivel Crossover Bracket--Stair (1/pack) Compound Swivel Bracket (2/pack1 top, 1 bottom) Aluminum Foot Block Touch-up Pen
XXCTBKTAL10PK XXFHBKTAL XXFSBKTAL XXSWHBKTAL XXSWSBKTAL XX25FHCBKTAL XX25RCSWSCBKTAL XXCPDSWBKTAL XXALFTBLK XXTOUCHUPPEN
XX = COLOR PREFIX:
BK Charcoal Black BZ Bronze WT Classic White
Aluminum railing has a textured finish.
55
RAILING
Trex Transcend® Railing
Transcend is either a 5-step or 3-step process. Choose Trex post sleeves, caps and skirts (Steps 1 & 2). Then choose each component separately for a custom design (5-step).
STEP
3a
COMPONENT
Top & Bottom Rails
In this step, two rails (1 top, 1 bottom) must be selected.
3b
DESCRIPTION
6' Crown Top Rail 8' Crown Top Rail
6' Universal Top/Bottom Rail 8' Universal Top/Bottom Rail
[6' Rail: 67.5 in (171 cm) actual length; 8' Rail: 91.5 in (232 cm) actual length]
ITEM NUMBER
XXCROWNTR06 XXCROWNTR08
XXUNIVTBR06 XXUNIVTBR08
Crown
Universal
Balusters
4
See chart below for number of balusters
needed to complete each railing section.
BALUSTER TYPE
PER 6' PER 8' SECTION SECTION
Square (Horizontal application)
13
18
Square (Stair application)
11
15
Aluminum (Horizontal application)
15
20
Aluminum (Stair application)
12
16
Aluminum balusters are available in Charcoal Black, Classic White and Bronze only (BK, WT, BZ).
Accessory Infi ll Kit
5 » 2 Baluster Spacers
» Adjustable Foot Block
» Mounting Hardware
[6' Rail: 67.5 in (171 cm) actual length; 8' Rail: 91.5 in (232 cm) actual length]
ACCESSORY
Trex Transcend®Accessories
All accessories include a quantity of 12 per box unless otherwise noted.
Square Balusters for 36" Rail Height (16/pack)
[1.418 in x 1.418 in x 30.375 in (36 mm x 36 mm x 771 mm) actual dimensions]
Square Balusters for 42" Rail Height (16/pack)
[1.418 in x 1.418 in x 36.375 in (36 mm x 36 mm x 923 mm) actual dimensions]
Round Aluminum Balusters for 36" Rail Height (20/pack)
[.75 in x 30.25 in (19 mm x 768 mm) actual dimensions]
Round Aluminum Balusters for 42" Rail Height (20/pack)
[.75 in x 36.25 in (19 mm x 920 mm) actual dimensions]
Square Aluminum Balusters for 36" Rail Height (20/pack)
[.75 in x 30.25 in (19 mm x 768 mm) actual dimensions]
Square Aluminum Balusters for 42" Rail Height (20/pack)
[.75 in x 36.25 in (19 mm x 920 mm) actual dimensions]
XX020230SBK XX020236SBK XXTA30RBK XXTA36RBK XXTA30SBK XXTA36SBK
6' Accessory Infi ll Kit for Square Balusters--Horizontal 6' Accessory Infi ll Kit for Square Balusters--Stair 8' Accessory Infi ll Kit for Square Balusters--Horizontal 8' Accessory Infi ll Kit for Square Balusters--Stair
6' Accessory Infi ll Kit for Round Aluminum Balusters--Horizontal 6' Accessory Infi ll Kit for Round Aluminum Balusters--Stair 8' Accessory Infi ll Kit for Round Aluminum Balusters--Horizontal 8' Accessory Infi ll Kit for Round Aluminum Balusters--Stair
6' Accessory Infi ll Kit for Square Aluminum Balusters--Horizontal 6' Accessory Infi ll Kit for Square Aluminum Balusters--Stair 8' Accessory Infi ll Kit for Square Aluminum Balusters--Horizontal 8' Accessory Infi ll Kit for Square Aluminum Balusters--Stair
6' Glass Panel Accessory Kit [Glass panel mounting hardware;
glass panel not included]
XXSQHIK06 XXSQSIK06 XXSQHIK08 XXSQSIK08
XXRDHIK06 XXRDSIK06 XXRDHIK08 XXRDSIK08
XXASBHIK06 XXASBSIK06 XXASBHIK08 XXASBSIK08
XXGLIK06
Mounting Hardware for Cut Rails --Horizontal Mounting Hardware for Cut Rails --Stair Transcend RSB Bracket Pack--Horizontal (24/box) Transcend RSB Bracket Pack--Stair (24/box) 0 Degree Rail Gasket Pack--Horizontal 0 Degree Rail Gasket Pack --Stair 22.5 Degree Gasket Pack 45 Degree Birdsmouth Gasket Pack (for 4x4) 45 Degree Gasket Pack (for 6x6)
XXHZACCYKIT XXSTACCYKIT TSHBRACKET TSSBRACKET XX00HGASK XX00SGASK XX22HGASK XX45RSBADAPK WT45HGASK
RAILING
Or simply choose a rail & baluster kit in Classic White (3-step).
Rail & Baluster Kit
3 » Crown Top Rail
» Universal Bottom Rail » Square Balusters » Baluster Spacers » Adjustable Foot Block » Mounting Hardware
Available in Classic White only.
6' x 36" Rail & Baluster Kit--Horizontal 6' x 36" Rail & Baluster Kit--Stair
8' x 36" Rail & Baluster Kit--Horizontal 8' x 36" Rail & Baluster Kit--Stair
[Actual dimensions: 6' Rail: 67.5 in x 36 in (171 cm x 914 mm); 8' Rail: 91.5 in x 36 in (232 cm x 914 mm)]
WT0636HRK WT0636SRK
WT0836HRK WT0836SRK
WT Classic White
FP Fire Pit
56
XX = COLOR PREFIX:
BK Charcoal Black
GP Gravel Path
RS Rope Swing TH Tree House
VL Vintage Lantern BZ Bronze(aluminum only)
Trex Select® Railing
Trex Select® is a 3-step process. Choose Trex post sleeves, caps and skirts (Steps 1 & 2) and a rail & baluster kit (Step 3).
STEP
3
COMPONENT
Classic White Rail & Aluminum Baluster Kit
» Top Rail » Bottom Rail » Round Aluminum Balusters » Adjustable Foot Block » Hardware Pack
Available in Classic White with Charcoal Black Aluminum Balusters only.
DESCRIPTION
ITEM NUMBER
6' x 36" Rail & Aluminum Baluster Kit--Horizontal 6' x 36" Rail & Aluminum Baluster Kit--Stair
WTRD0636HSELK WTRD0636SSELK
8' x 36" Rail & Aluminum Baluster Kit--Horizontal 8' x 36" Rail & Aluminum Baluster Kit--Stair
6' x 42" Rail & Aluminum Baluster Kit--Horizontal 8' x 42" Rail & Aluminum Baluster Kit--Horizontal 8' x 42" Rail & Aluminum Baluster Kit--Stair
WTRD0836HSELK WTRD0836SSELK
WTRD0642HSELK WTRD0842HSELK WTRD0842SSELK
[Actual dimensions: 6' Rail: 67.5 in x 36 in / 42 in (171 cm x 914 mm / 106 cm); 8' Rail: 91.5 in x 36 in / 42 in (232 cm x 914 mm / 106 cm);
ACCESSORY Trex Select® Accessories
Trex Select® 8' Aluminum Rail Stiffener
Mounting Hardware for Cut Rails-- Horizontal (10 kits/box)
Mounting Hardware for Cut Rails-- Stair (10 kits/box)
BKENHZBKT BKENSTBKT SELALRAILSTIFFENER
Trex Aluminum Gates
COMPONENT
DESCRIPTION
ITEM NUMBER
Gate Rail Kit
36" Rail Height, Square Balusters, Adjustable up to 48" wide opening 36" Rail Height, Round Balusters, Adjustable up to 48" wide opening
42" Rail Height, Square Balusters, Adjustable up to 48" wide opening
Available in all Aluminum colors. 42" Rail Height, Round Balusters, Adjustable up to 48" wide opening
[Actual height 36" Rail: 36 in (914 mm); 42" Rail: 42 in (106 cm) Actual width is 47.5 in (120 cm) but can be cut to fi t any width.]
XX36SQADJGATE XX36RDADJGATE XX42SQADJGATE XX42RDADJGATE
Hardware Pack
(black only) (purchased separately)
2 Adjustable Self-Closing Hinges
BKGATEHW
1 Locking Hasp With Keys
Hardware for attachment to wood post with composite sleeve or aluminum posts
Trex Aluminum ADA Compliant Handrail
All Trex ADA handrail components are made of powder-coated aluminum. For detailed installation instructions, visit trex.com.
COMPONENT
Corner Mount Post Return ("Candy Cane") 5 Degree Elbow 31 Degree Elbow 34 Degree Elbow 36 Degree Elbow 90 Degree Elbow Collar Rail End Cap 90 Degree Wall Return Wall Mount 4 in (101 mm) Internal Connector 1.375 in x 8 ft (34 mm x 243 cm) Hand Rail
ITEM NUMBER
XXALADAICORNER XXALADA180CCANE XXALADA05ELB XXALADA31ELB XXALADA34ELB XXALADA36ELB XXALADA90ELB XXALADACLR XXALADACAP XXALADA90WR XXALADAWMNT XXALINTCONN XXALADARAIL8
XX = COLOR PREFIX:
BK Charcoal Black BZ Bronze WT Classic White Aluminum railing has a textured finish.
RAILING
57
TREX TRANSCEND RAILING
NOTES: » TREX TRANSCEND RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF
PRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED. » A ll Trex Transcend railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (1718 mm) for
6' (1.83 m) on center, and 91-5/8" (2353 mm) for 8' (2.44 m) on center. Note that railings are designed to be slightly longer than required to allow for very slight play in post placement some minimal trimming may be required. IT IS VERY IMPORTANT TO MEASURE FIRST.
PARTS
A
G*
R
BALUSTER OPTIONS
P S
C
O
D*
**
I
Balusters
F (standard shown)
E
C
Glass Panel Option
Q*
S R
P
Standard
Round Aluminum
Square Aluminum
O
J
N
H*
B
NOTE: Pictorial representations shown may only show one style of railing, while others may also be used. Review detailed instructions to determine what railing styles and combinations can be used.
L
K
DETERMINING BALUSTERS NEEDED
M
Baluster Type
Per 6' OC Section
Per 8' OC Section
A. Crown or Universal B. Universal C. Trex railing support bracket (RSB) D. TrexExpressTM Railing Assembly Template* E. Rail gaskets F. Balusters G. Post sleeve cap* H. Post sleeve skirt* I. Post sleeve 4" x 4" (102 mm x 102 mm) or
6" x 6" (152 mm x 152 mm) post sleeve)** J. Trex decking K. Trex fascia L. Code-approved wood joist 2" x 8"
(51 mm x 203 mm) M. Code-approved wood rim joist 2" x 8"
(51 mm x 203 mm) or larger N. A djustable foot block (quantity of one is required for
all railing span lengths) O. Baluster spacer
Trex Transcend Glass Panel Parts List
P. Panel support molding Q. Tempered glass panel* R. Trex panel support molding spacer S. Weatherstripping
Square
13
18
(Horizontal Application)
Square
11
15
(Stair Application)
Round/Square Aluminum
15
20
(Horizontal Application)
Round/Square Aluminum
12
16
(Stair Application)
NOTE: Basic installation for balusters is the same for all options. When using round or square aluminum balusters, use correct baluster spacers.
NOTE: If installing 42" (1067 mm) railing, use longer posts sleeves and measure accordingly to ensure a proper cut. DO NOT CUT TO ACTUAL 42" LENGTH WITHOUT CONFIRMING WHAT STYLE OF RAILING YOU ARE INSTALLING.
NOTE: If using post mounts, refer to detailed instructions provided with post mounts for attaching these prior to installation of any railing type.
Screws Supplied with RSB C1. Wood screw for attachment
of RSB to wood post/composite sleeve
C2. Self-tapping rail screw for attachment of railing to RSB
* Item not included in the Transcend railing kits. ** B oth 4" x 4" (102 mm x 102 mm) and 6" x 6" (152 mm x 152
mm) post sleeves are designed to fit over 4x4 pressuretreated post
58 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
TRANSCEND RAILING
TREX TRANSCEND
RAILING CONFIGURATIONS
Note: See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing.
Standard Crown
B A
D C
Cutting post sleeves is NOT required. A. Pressure-treated post/Trex post sleeve, Trex post mount/Trex post sleeve*, or Joist
Mount Post/Trex post sleeve* (INSIDE MOUNT ONLY) B. Crown rail C. Universal bottom D. Trex balusters See page 60 for "How to Install Standard Railing".
Cocktail
B
C
A
E
D
Post sleeves will need to be cut. A. Pressure-treated post with Trex Transcend post sleeve
NOTE: » .O nly for use with 4" x 4" (102 mm x 102 mm) post sleeve.
POST SLEEVES
WILL NEED TO
» Trex post mounts cannot be used with Transcend cocktail
BE CUT
design.
B. Deck board top rail (1 x 6 or 2 x 6). NOTE: Contour and Escapes cannot be used.
C. Universal top rail
D. Universal bottom
E. Trex balusters
See page 62 for "How to Install Cocktail Railing".
NOTE: Additional pan head screws will need to be purchased - see detailed instructions.
Traditional
B
C
A
E
D
Cutting post sleeves is NOT required. A. Pressure-treated post/Trex post sleeve, Trex post mount/Trex post sleeve*, or Joist
mount post/Trex post sleeve* (INSIDE MOUNT ONLY) B. 2" x 4" (51 mm x 102 mm) lateral top rail C. Universal top rail D. Universal bottom E. Trex balusters See page 63 for "How to Install Traditional Railing". NOTE: Additional pan head screws will need to be purchased - see detailed instructions.
Round Aluminum
Square Aluminum
» Follow desired railing style instructions found above, substituting correct baluster spacer for type of baluster being used.
» Refer to detailed instructions for added steps when using round and square aluminum balusters. See page 64.
TRANSCEND RAILING
Glass Panel
B A
D C
Cutting post sleeves is NOT required. A. Pressure-treated post/Trex post sleeve, Trex post mount/Trex post sleeve**, or Joist
mount post/Trex post sleeve** (INSIDE MOUNT ONLY) B. Crown rail (use universal rail if building cocktail or traditional design with glass inserts) C. Universal bottom D. Tempered glass panel (NOT included in kit) See page 65 for "How to Install Standard Glass Panel Railing", page 67 for "How to Install Cocktail Style Glass Panel Railing" (**NOTE: Trex Post Mounts or Trex Joist Mount Posts cannot be used with this railing configuration), and page 68 for "How to Install Traditional Style Glass Panel Railing". NOTE: Glass panels are not recommended in stair applications.
59
HOW TO INSTALL STANDARD RAILING
TREX TRANSCEND
Installing Railing Support Brackets (RSBs)
Option 1: Without Trex Express railing template
3a
35-1/16\" ((88991.1mcm)
or 41-1/16\" (1043 mm)
3b
1
2
5-1/2" (140 mm)
3
4
Read all instructions BEFORE installation. Important: Post sleeves are NOT to be cut for this design style.
Installing Pressure-
1
Treated Posts
»Posts are to be installed 6' (1.83 m) or 8' (2.44 m) on center
2" x 8" (51 mm x 203 mm)
min.
1" (25 mm) min.
to accommodate
5-1/8" (130 mm) min.
appropriate railing length.
»Attach posts using 1/2"
(130 mm) carriage bolts.
» Minimum joist size is
2" x 8" (51 mm x 203 mm).
» Top bolts must be 1" (25
mm) from tops of joists.
» Bottom bolts must be 5-1/8" (130 mm) from top
bolts.
» Bolts can be countersunk flush with framing to allow
for fascia attachment.
NOTE: Blocking can be added for extra strength.
Installing Post Sleeve
2
Skirts and Post Sleeves
2. Slide post sleeve skirt
over post and down to
2
rest on decking surface.
1
Slide post sleeve over
post and position inside
post sleeve skirt.
NOTE: Shims can be used to plumb post sleeves.
3a. Mark 5-1/2" (140 mm) and 35-1/16" (891 mm) from .deck surface OR for 42" (1067 mm) height, mark 5-1/2" (140 mm) and 41-1/16" (1043 mm) from the deck surface.
3b. Place RSBs directly under marks, center on posts, and secure with 2" (51 mm) wood screws (provided with post sleeve). Place top RSBs flat side up, bottom RSBs flat side down.
Option 2: With TrexExpress railing template
3c
3d
1
3
3
2
3c. .Place RSBs in template. Place top RSBs flat side UP, bottom RSBs flat side DOWN. Secure template on post with tape or rubber band, with bottom of template resting on post skirt.
3d. Secure RSBs with 2" (51 mm) wood screws (provided in railing kit) and remove template.
NOTES: Special steps are necessary when using 6" x 6" (152 mm x 152 mm) plastic TrexExpress
template. » Cut off 1/2" (13 mm) from the bottom (blue
arrows up) of the tool BEFORE first use. » Position top RSBs ONLY, 6" (152 mm) higher for
42" (1067 mm) rail height. »Secure RSBs with 2-1/2" (64 mm) wood screws
(provided with post sleeve) and remove template.
TRANSCEND RAILING
60 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL STANDARD RAILING/CONTINUED
TREX TRANSCEND
Cutting Railings and Baluster Spacers
4
5
Attaching Bottom Rail
7
(Universal Rail)
7.Lift bottom rail so
RSBs are in the channel and attach with three self-tapping
1 1
screws provided (use three outer holes; do
2 2 Hole
RSB
3
2
Hole RSB
not use hole in RSB
that is closest to post).
If two hole bracket is included, attach with two self-
tapping holes (provided).
4.Measure between posts and cut rails to same length. 5.Cut baluster spacers the same length as rails, equally
spaced, so holes line up.
NOTES: » If using optional rail gaskets, subtract 1/16" (1.6 mm)
from each end. » Attach baluster spacers to railing before cutting to
allow for cleaner cut and less work. » When measuring, cut equal lengths from each side of
railing and baluster spacer to ensure equal spacing of balusters per each railing section. » In some cases, the gasket can be attached before tightening railing to RSB. »If gaskets are tight, use a small flat head screwdriver to compress the tabs of the gasket if they are stuck outside the rail.
IMPORTANT NOTE REGARDING FOOT BLOCK INSTALLATION: » One foot block is REQUIRED for all
railing spans. » Refer to detailed instructions (Trex
Transcend® rail instructions) included with foot block prior to installation of railing section as these include other required steps for proper installation.
Attaching Foot Block to Bottom Rail
6.Invert the bottom rail.
Center and drill a hole
6b
using a 3/16" drill bit. This
will be location for foot
block attachment
(to be installed last).
Attaching Top Rail
8
Crown Rail
8.Place crown rail on
1
RSBs. Attach top rail
to RSB with three
self-tapping screws provided (use three outer holes; do not
x2
2 Hole RSB
x2
3 Hole RSB
use hole in RSB that is
2
2
closest to post). If two
hole bracket is included, attach with two self-tapping
screws (provided).
Placing Baluster Spacers 9
9. Snap baluster spacer into bottom rail. Place inverted baluster spacer on top of first baluster spacer.
Attaching Balusters
10. Place baluster into
10
both baluster spacers,
ensuring that balusters
2
are fully seated into the
channel. Working at
slight angle, maneuver
balusters into top rail.
1
See page 64 if using
Aluminum round or
square balusters for
additional information.
TRANSCEND RAILING
61
HOW TO INSTALL STANDARD RAILING/CONTINUED
TREX TRANSCEND
11. S lide baluster spacer up 11
and snap into top rail. Place optional top rail gaskets on each end of rail.
Option
Attaching Post Caps and 12
Installing Foot Blocks
2
2
12. Secure post caps with
silicone or PVC adhesive.
Attach foot block per
2
foot block instructions.
1
NOTE: Clean up any excess
adhesive before it dries.
3
HOW TO INSTALL COCKTAIL RAILING
TREX TRANSCEND 2. Installing Post Sleeve Skirts and Post Sleeves See
instructions on page 60.
3. .Installing Railing Support Brackets (RSBs) instructions on page 60.
4. C utting Railings and Baluster Spacers See instructions on page 61.
5. Attaching Foot Block to Bottom Rail See instructions on page 61.
IMPORTANT NOTES: » O NLY use with 4" x 4" (102 mm x 102 mm) post and
post sleeve. Cutting post and post sleeve ONLY apply
to the Transcend Cocktail railing. » If using Select decking, USE maximum length 1-3/4"
(44 mm) screw and NOT 2" (51 mm) screw. » Screws that are used for attaching decking board to
railing MUST be attached at an angle to prevent screw
from penetrating through the top of decking board.
1. Installing Pressure-Treated Posts See instructions on page 60.
Cutting Post and Post Sleeve 1a.Mark and cut post and
post sleeve measuring from deck surface: » 36-3/16" (919 mm)
for 36" (914 mm) height. » 42-3/16" (1072 mm) for 42" (1067 mm) height.
1a
36-3/16" (919 mm)
or 42-3/16" (1072 mm)
6. A ttaching Bottom Rail (Universal Rail) See instructions on page 61.
Attaching Inverted Universal Rail as Top Rail
7
1
8
1 1
x2
2 Hole RSB
3
2
Hole
RSB
2
2
3
7. Place inverted universal rail onto RSBs. Attach universal rail to RSBs with three self-tapping screws provided (use three outer holes; do not use hole in RSB that is closest to post). If two hole bracket is included, attach with two self-tapping screws (provided).
8. Place deck boards (DO NOT use Escapes deck boards for top rail) over universal rails. Attach
boards on each post with Trex-recommended composite screws (quantity of 2 per each board end). Secure boards to universal rails from underside of railing into bottom of decking board, with 2" (51 mm) pan-head screws (not provided) at an angle every 16" (406 mm) on center.
62 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
TRANSCEND RAILING
HOW TO INSTALL COCKTAIL RAILING/CONTINUED
TREX TRANSCEND
9
Optional
11. Attaching Balusters
11
See instructions on
page 61 for standard
balusters and page 65
for aluminum balusters.
9. Use scarf cut for posts w here two deck boards meet.
NOTES: » If necessary, cut tips off rail gaskets prior
to installation. » L eave 1/8" (3 mm) gap between deck boards. » D eck boards can overhang end of last post
maximum 1/2" (13 mm).
10. P lacing Baluster Spacers See instructions on page 61.
12.S lide baluster spacers up and snap into universal rails.
13.Installing Foot Block Attach foot block per detailed instructions.
HOW TO INSTALL TRADITIONAL RAILING
TREX TRANSCEND
6. A ttaching Bottom Rail (Universal Rail) See instructions on page 61.
1. Installing Pressure-Treated Posts See instructions on page 60.
2. Installing Post Sleeve Skirts and Post Sleeves See instructions on page 60.
3. Installing Railing Support Brackets (RSBs) See instructions on page 60.
4. Cutting Railings and Baluster Spacers See instructions on page 61.
5. Attaching Foot Block to Bottom Rail See instructions on page 61.
Attaching Inverted Universal Rail as Top Rail
7. Place inverted universal
rail onto RSBs. Attach
7
universal rail with three
self-tapping screws
1
provided (use three
outer holes; do not use hole in RSB that is closest to post). If two hole bracket is included, attach with
x2
2
2 Hole RSB
x2
3 Hole RSB
2
two self-tapping holes
(provided).
8. M easure between posts and cut 2" x 4" (51 mm x 102 mm) to length. Place 2" x 4" (51 mm x 102 mm) on universal rail. Attach board to rail with 2" (51 mm) pan-head screws (not provided) every 16" (406 mm) on center.
8
1 2
TRANSCEND RAILING
NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements. 63
HOW TO INSTALL TRADITIONAL RAILING/CONTINUED
TREX TRANSCEND
9.Pre-drill a pilot hole and 9
12
toenail 2-1/2" (64 mm)
1
composite decking
1
screw (not provided) at
each end of 2" x 4"
(51 mm x 102 mm) into
post on back side of
rail (sid2e not facing
3
decking).
Optional
10. Placing Baluster Spacers See instructions on page 61.
11. Attaching Balusters See page 61 for standard baluster and instructions below for aluminum balusters.
12.S lide baluster spacer up and snap into universal rail.
NOTE: If necessary, cut tips off rail gaskets prior to installation.
13. Attaching Post Caps and Installing Foot Block Attach foot block per detailed instructions.
HOW TO INSTALL ROUND OR SQUARE ALUMINUM BALUSTERS
TREX TRANSCEND
1. Installing Pressure-Treated Posts See instructions on page 60.
2. .Installing Post Sleeve Skirts and Post Sleeves See instructions on page 60.
3. .Installing Railing Support Brackets (RSBs) See instructions on page 60.
4. Cutting Railings and Baluster Spacers See instructions on page 61.
5. Attaching Foot Block to Bottom Rail See instructions on page 61.
Installing Lower Aluminum Baluster Adaptor Strip
7.After bottom rail is
fully installed, place
7
aluminum baluster
adaptor strip into
channel of bottom
rail, ensuring that
it's fully seated into
the channel. When
rail lengths are non-
standard, the baluster
adaptor strip will need to be cut 2-1/2"
(64 mm) shorter than the rail to allow clearance for
the RSB's on each end.
6. Attaching Bottom Rail (Universal Rail) See instructions on page 61.
8.Attaching Top Rail See specific instructions based on top rail of choice.
Installing Upper Aluminum Baluster Adaptor Strips
and Baluster Spacers
9.After top rail is fully
9
installed, place aluminum
baluster adaptor strip
into channel of top rail,
ensuring that it's fully
seated into the channel.
TRANSCEND RAILING
64
HOW TO INSTALL ROUND OR SQUARE ALUMINUM BALUSTERS/CONTINUED
TREX TRANSCEND
10.S nap baluster spacer
10
into bottom rail. Place
inverted baluster
spacer on top of first
baluster spacer.
12. Slide baluster spacer up 12
and snap into top rail.
Place optional top rail
2
gaskets on each end of
rail.
Attaching Balusters
11.Working at slight angle, press baluster
11
through both baluster 2
spacers and into bottom
aluminum baluster
adaptor strip, ensuring
balusters are tight. Once
balusters are seated
1
into aluminum baluster
adaptor strip on bottom
rail, maneuver baluster into upper rail aluminum
baluster adaptor strip. Some force will be needed to
press balusters into place and level them.
Tip: Ensure balusters are level prior to attempting to slide baluster spacer up. This will allow for the baluster spacer to move up freely and snap into upper rail. Use of a rubber mallet to gently tap balusters in level is recommended.
HOW TO INSTALL STANDARD GLASS PANEL RAILING
TREX TRANSCEND
NOTES: Read all instructions BEFORE installation. » You must purchase the 1/4" (6 mm) tempered glass
panels. See dimensions below. » Glass panels ONLY for use with maximum 6' (1.83 m)
on center post spacing. » Not recommended for stair applications.
TRANSCEND RAILING
65
HOW TO INSTALL STANDARD GLASS PANEL RAILING/CONTINUED
TREX TRANSCEND
TEMPERED GLASS PANEL DIMENSIONS
»36" (914 mm) high rail: 1/4" x 30" x 63-1/2" max. (6 mm x 762 mm x 1613 mm)
»42" (1067 mm) high rail: 1/4" x 36" x 63-1/2" max. (6 mm x 914 mm x 1613 mm)
1. Installing Pressure-Treated Posts See instructions on page 60.
2. Installing Post Sleeve Skirts and Post Sleeves See instructions on page 60.
3. Installing Railing Support Brackets (RSBs) See instructions on page 60.
4. C utting Railings See instructions on page 61.
5. Attaching Foot Block to Bottom Rail See instructions on page 61.
6. A ttaching Bottom Rail (Universal Rail) See instructions on page 61.
Attaching Weatherstripping and Positioning Panel
7
8
63-1/2" (1613 mm)
2" (51 mm)
Attaching Top (Crown)
9
Rail 9. Place top rail over RSB
1 1
brackets and glass
panel. Attach top rail
to RSB with three self-tapping screws provided (use three
x2
2 Hole RSB
x2
3 Hole RSB
outer holes; do not
2
2
use hole in RSB that
is closest to post). If two hole bracket is included,
attach with two self-tapping screws (provided).
NOTE: Avoid hitting glass panel while using the drill.
Attaching Panel Support
Molding
10
10.P ush PSM into rail
to complete snap
connection. Lower rail
PSM edge rests on top
of rail. Top rail PSM
snaps flush into rail.
Hiding Brackets
11.Cut Transcend baluster 11
spacer into four lengths equal to distance between the glass panel and posts. Cut slowly and one at a time, to avoid chipping.
12.Snap spacer into bottom
and top rail to hide
12
brackets and create a
seamless look.
7.Push black-edged trim onto upper and lower edges of panel. Trim should be the exact length of the glass panel. Extra trim can be cut with razor blade or scissors.
8. Position panel with weatherstripping into lower rail channel. Center panel between posts with about 2" (51 mm) of air space on each side of panel.
13. A ttaching Post Caps and Installing Foot Blocks See instructions on page 62 and detailed foot block instructions..
TRANSCEND RAILING
66 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL COCKTAIL STYLE GLASS PANEL RAILING
TREX TRANSCEND
4. Cutting Railings See instructions on page 61.
5. Attaching Foot Block to Bottom Rail See instructions on page 61.
6. A ttaching Bottom Rail (Universal Rail) See instructions on page 61.
7-8.Attaching Weatherstripping and Positioning Panel See instructions on page 66.
NOTES: Read all instructions BEFORE installation. » You must purchase the 1/4" (6 mm) tempered glass
panels. See dimensions below. » Glass panels ONLY for use with maximum 6' (1.83 m)
on center post spacing. » NOT recommended for stair applications. » Trex post mounts cannot be used for this application. » If using Select decking, USE maximum length 1-3/4"
(45 mm) screw and NOT 2" (51 mm) screw. » S crews that are used for attachment of decking board
to railing MUST be attached at angle to prevent screw from penetrating through top of decking board.
Attaching Top Rail
9
TEMPERED GLASS PANEL DIMENSIONS
» 36" (914 mm) high rail: 1/4" x 30" x 63-1/2" max. (6 mm x 762 mm x 1613 mm)
» 42" (1067 mm) high rail: 1/4" x 36" x 63-1/2" max. (6 mm x 914 mm x 1613 mm)
9. Cut deck boards to appropriate length of railing span, remembering to include extra space on each side of the deck board to allow for attachment to the post. Decking boards must cover 1/2 of the pressuretreated post to allow this to be fastened later. If you include extra decking material on each side this can be cut off later if needed.
10
11
1. Installing Pressure-Treated Posts See instructions on page 60.
NOTE: If installing glass with cocktail rail design, rail posts and post sleeves must be cut.
1a. Cutting Post and Post Sleeve See instructions on page 62.
2. Installing Post Sleeve Skirts and Post Sleeves See instructions on page 60.
3. Installing Railing Support Brackets (RSBs) See instructions on page 60.
10.P lace inverted deck board (place top side of deck board down) on clean, flat surface. (DO NOT use Escapes deck boards for top rail.)
11. P lace Universal rail (orient this properly so when flipped over, the universal rail will accept the baluster spacer and balusters), on the deck board, centered in both directions to allow final attachment to post.
TRANSCEND RAILING
67 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO ATTACH COCKTAIL STYLE GLASS PANEL RAILING/CONTINUED
TREX TRANSCEND
12. Secure deck board
12
to Universal rail with
2" (51 mm) pan head
screws (not provided)
approximately every
16" (406 mm) on center
at an angle. (DO NOT
overtighten. Attach from
underside of railing into
bottom of decking board.)
14.Attach deck board
14
to post (ensure that
screws are attached
to wood post) with
Trex recommended
composite screws
(quantity of 2 per each
board end).
13.P lace inverted Universal 13
rail with deck board
attached onto RSB's
1 1
with glass panel in
the channel. Attach
Universal rail to RSB's
with three self-tapping screws provided (use three outer holes; do
2 Hole RSB
2
3 Hole RSB
2
not use hole in RSB that
is closest to post). If two hole bracket is included,
attach with two self-tapping screws (provided).
15.Attaching Panel Support Moldings See instructions on page 66.
16-17. Hiding Brackets See instructions on page 66.
18. Installing Foot Block Attach foot block per detailed instructions.
TRANSCEND RAILING
HOW TO ATTACH TRADITIONAL STYLE GLASS PANEL RAILING
TREX TRANSCEND
NOTES: Read all instructions BEFORE installation. » You must purchase the 1/4" (6 mm) tempered glass
panels. See dimensions below. » Glass panels Only for use with maximum 6'
(1.83 m) on center post spacing. » NOT recommended for stair applications.
TEMPERED GLASS PANEL DIMENSIONS
» 36" (914 mm) high rail: 1/4" x 30" x 63-1/2" max. (6 mm x 762 mm x 1613 mm)
» 42" (1067 mm) high rail: 1/4" x 36" x 63-1/2" max. (6 mm x 914 mm x 1613 mm)
68
HOW TO ATTACH TRADITIONAL STYLE GLASS PANEL RAILING/CONTINUED
TREX TRANSCEND
1. Installing Pressure-Treated Posts
11
12
See instructions on page 60.
2. Installing Post Sleeve Skirts and Post Sleeves See instructions on page 60.
3. Installing Railing Support Brackets (RSBs) See instructions on page 60.
4. Cutting Railings See instructions on page 61.
5. Attaching Foot Block to Bottom Rail See instructions on page 61.
6. .A ttaching Bottom Rail (Universal Rail) See instructions on page 61.
11. P lace Universal rail (remembering to orient this properly so that when flipped over, the Universal rail will accept the baluster spacer and balusters), on the 2" x 4" (51 mm x 102 mm), centered.
12. Secure 2" x 4" (51 mm x 102 mm) to Universal rail with 2" (51 mm) pan head screws (not provided) approximately every 16" (406 mm) on center.
7-8. Attaching Weatherstripping and Positioning Panel See instructions on page 66.
Attaching Top Rail
13
14
1 1
9
9. Cut 2" x 4" (51 mm x 102 mm) to same length of the inverted Universal rail.
2
3
3
Hole
Hole
RSB
RSB
2
2
13.P lace inverted Universal rail with 2" x 4" (51 mm x 102 mm) attached onto RSB's with glass panel in the channel. Attach Universal rail to RSB's with three self-tapping screws provided. (Use three outer holes; do not use hole in RSB that is closest to post.) If twohole bracket is included, attach with two self-tapping screws (provided).
14.P re-drill a pilot hole and toenail 2-1/2" (64 mm) composite deck screw (not provided) at each end of the 2" x 4" (51 mm x 102 mm) into post on back side (side not facing decking).
10.P lace inverted 2" x 4"
10
(51 mm x 102 mm) (place
top side down) on clean,
flat surface.
15. Attaching Panel Support Moldings See instructions on page 66.
16-17. Hiding Brackets See instructions on page 66.
18. .A ttaching Post Caps and Installing Foot Block
See instructions on page 62 and detailed foot block instructions.
TRANSCEND RAILING
69 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL ON-AN-ANGLE RAILING
TREX TRANSCEND (CROWN AND UNIVERSAL RAILING)
NOTE: Trex railing brackets are designed to be installed up to a 45° angle.
4 x 4
6 x 6
NOTES: »Small angles (1° - 30°). Both 4" x 4" (102 mm x
102 mm) or 6" x 6" (152 mm x 152 mm) post sleeves work well. » Large angles (31° - 45°). USE ONLY 6" x 6" (152 mm x 152 mm) post sleeves when installing on flat side. » 45° angles using 4" x 4" (102 mm x 102 mm) post sleeves MUST use Transcend Bird's Mouth brackets. » Using 6" x 6" (152 mm x 152 mm) post sleeves at 45° angles. Brackets are installed off-center and use 45° Transcend gaskets. »Railing gaskets are designed to fit at 0°, 22.5°, and 45° angles. Gaskets are labeled with appropriate angle dimension.
HOW TO INSTALL CROWN AND UNIVERSAL BIRD'S MOUTH RAILING
TREX TRANSCEND
NOTES: » Use with 4" x 4" (102 mm x 102 mm) post sleeve
ONLY. »Gaskets are only designed for use with Transcend
Crown and Universal Railing.
Read all instructions before installation.
PARTS
Mark Posts
1
1.Measure and mark
4" (102 mm) and
33-9/16" (852 mm) up
from top of post skirt.
NOTE: Without skirt, add 1-1/2" (38 mm) to measurements.
Attaching Adapters Snap adapters into RSBs.
33-9/16" (852 mm)
for 36" (914 mm)
4" (102 mm)
Adapter Top bracket
Pre-drill Bottom and Top RSBs
2
3
TRANSCEND RAILING
Adapter Bottom bracket
2.Position RSBs with adapter (flat side DOWN) for lower rail, mark and pre-drill screw holes with 1/8" (3 mm) drill bit on post.
3. Position RSBs with adapter (flat side UP) for top rail, mark and pre-drill screw holes with 1/8" (3 mm) drill bit on post.
70
HOW TO INSTALL CROWN AND UNIVERSAL BIRD'S MOUTH RAILING/CONTINUED
TREX TRANSCEND
Measuring and Cutting Rails
4
Installing Railings to
6
RSB's
6. Attach with self-tapping
screws (provided).
4.Measure from corner-to-corner between posts. Mark 45° cuts on rails with template on assembly tool. Center of "V's" is the distance from corner-to-corner for posts.
NOTE: Subtract 1/16" (1.6 mm) from each end to accommodate rail gaskets.
Attaching Top and
5
Bottom RSBs
5. Attach RSBs with
adapters to posts
with wood screws
(provided).
NOTES: »Drill at slight inward angle
to drill holes on marks. »Lay cut lower rail into
position on decking surface between the posts before attaching the lower RSB. There may be some difficulty attaching the lower rail if you fail to do this.
Using Miter Box Saw to Cut Rails 1.Place 2" x 4" (51 mm x 102 mm) on edge behind the rail to allow for complete cut. 2. Angle blade to 45°. 3. Set stop on saw so blade travels half the depth of rails. Several test cuts can be made on scrap material to accurately set the stop. 4. "V" cut both sides of the rail.
2" x 4" (5.11 mcmm xx 1100.2 mm)
NOTE: Transcend's Crown and Universal Rails will require different stop settings.
HOW TO INSTALL CROWN AND UNIVERSAL STAIR RAILING
TREX TRANSCEND
Read all instructions BEFORE installation.
NOTE: All Transcend railings and gaskets ONLY WORK WITH STAIR SLOPES OF 32°-37°.
Installing Posts, Post
1
Sleeve Skirts, and Post
Sleeves for Stair Rails
1. Install posts, post sleeve
skirts, and post sleeves
according to standard
Transcend railing
instructions.
See page 60.
» In most cases, a post and post sleeve longer than 39" (991 mm) will be needed on the lower section of stair rail to accommodate stair angle.
» Make sure top and bottom posts for stairs are installed at nose of each tread.
Measuring and Cutting
2a
Railings
2a. S nap baluster spacers
into top and bottom
railings, ensuring the
baluster spacer holes
line up parallel.
TRANSCEND RAILING
71 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL CROWN AND UNIVERSAL STAIR RAILING/CONTINUED
TREX TRANSCEND
2b. Set bottom and top rail 2b
along the nose of the stair treads, ensuring baluster holes are placed evenly. Also allow for a minimum of 1-1/2" (38 mm) at each end of rail for bracket placement and baluster clearance. Cut rails on marks.
NOTES: »If using railing gaskets,
subtract 1/16" (1.6 mm) maximum, from each end and cut. »CUT VERY CAREFULLY TO NOT BREAKBALUSTER SPACERS.
3. Position bottom rail between posts and slide Trex ExpressTM railing assembly template into position with bottom rail outline on template aligned with end of bottom rail. Allow a minimum clearance of 1" (25 mm) from stair tread. Secure template with rubber bands. Remove rail.
Attaching RSBs to BOTTOM Post
4
1
3
1
2
4
Cutting Balusters on Angle (OPTIONAL)
2c
2d
4.Attach upper and lower RSBs to bottom post, flat side UP, with wood screws provided. Remove template and place a second RSB, turned upside down, and interlock on each bracket.
Positioning RSBs on UPPER Post
5
2c.In order for balusters to seat properly (depending on the angle of the stair railing), the balusters may need to be trimmed to match the angle of the bottom and top railing.
2d.C arefully remove baluster spacers from rails.
Positioning RSBs on BOTTOM Post
3
2 1
3
2
11 3
5. Position pre-cut bottom rail between posts. Slide Trex ExpressTM railing assembly template into position, aligning bottom rail outline on template with end of bottom rail. Use rubber bands to hold template in place. Remove rail.
TRANSCEND RAILING
72
TRANSCEND RAILING
1
3 3 21
HOW TO INSTALL CROWN AND UNIVERSAL STAIR RAILING/CONTINUED
TREX TRANSCEND
Attaching RSBs to UPPER Posts
6
1
3
1
2
4
6.Attach upper and lower RSBs to top post, flat side DOWN. Remove template. Take second RSB, turn upside down and interlock into each bracket.
Attaching Top Rail 10a. Place top rail of
10a
choice (Crown rail 2
shown here) on
RSB's in rail channel
and attach with 3
self-tapping screws
(provided). Use the
three outer holes
in RSB to attach screws.
Upper Post Location -
Top Rail
Lower Post Location -
Top Rail
10b.If installing a
(view from under rail)
(view from under rail)
different railing
configuration other than Crown Railing, refer to
other Railing Configurations in Horizontal sections
for additional requirements.
Attaching Foot Block to Bottom Rail 7.See detailed instructions included with foot block.
11. S lide baluster spacer up 11
and snap into top rail.
Attaching Bottom Rail
8
2
(Universal Rail)
8.Lift bottom rail so RSB's
are in the channel and
attach with 3 self-tapping
1
screws (provided). Use the
three outer holes in RSB
to attach screws.
Upper Post Location Bottom Rail
Placing Baluster Spacers and Balusters
9
Lower Post Location Bottom Rail
Attaching Optional Gaskets 12. Stair railing gaskets
are designed to fit at slopes of 32° to 37°. Gaskets are labeled in order to ensure correct location.
Universal Rail Stair Gasket Locations
STR T2 B1
STR T1 B2
STR T1 B2
STR T2 B1
9.Snap baluster spacer into bottom rail. Place inverted baluster spacer on top of first baluster spacer making sure that holes line up parallel. Place balusters in baluster spacer holes.
Attaching Post Caps and Installing Foot Block
13. Secure post caps
with silicone or PVC 13
adhesive. Attach
2
foot block per foot
block instructions.
NOTE: Clean-up any
1
excess adhesive before it
dries.
3
73 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
TREX® SIGNATURETM RAILING
NOTES:
» TREX® SIGNATURETM POSTS CANNOT BE USED WITH TREX® SIGNATURETM TRADITIONAL OR TREX® SIGNATURETM COCKTAIL DESIGNS, ONLY PRESSURE-TREATED POSTS/POST SLEEVES CAN BE USED. REFER TO DETAILED INSTRUCTIONS FOR MORE INFORMATION.
» TREX® SIGNATURETM RAILINGS ARE DESIGNED TO BE ATTACHED WITH POSTS INSTALLED AT A CLEAR SPAN OF 6' (1.83 M) OR 8' (2.44 M).
» IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING POST-TO-POST CONFIGURATION, THE BOTTOM RAIL WILL NOT NEED TO BE CUT, BUT THE TOP RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT.
» IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING CROSSOVER POST CONFIGURATION (SPANS FROM ONE CROSSOVER POST TO ANOTHER CROSSOVER POST), BOTH THE BOTTOM RAIL AND TOP RAIL WILL NOT NEED TO BE CUT.
» IN ADDITION, AT ALL FINAL END POST CONFIGURATIONS, TOP RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT.
» S EE INFORMATION WITHIN DETAILED INSTRUCTIONS FOR MORE INFORMATION.
» S EE PAGE 55 FOR SKU NUMBERS.
PARTS
A P
E
F
K K C
I
I
D
BALUSTER OPTIONS
J B
L
O
G H
N
H M
Square Round
DETERMINING BALUSTERS NEEDED
Baluster Type
Square
Round
Per 6' Section
15
15
Per 8' Section
20
20
Per 6' Stair Section
13
13
Per 8' Stair Section
17
17
NOTE: THIS IS AN OVERVIEW OF ALL RAILING COMPONENTS FOR TREX® SIGNATURETM HORIZONTAL APPLICATIONS REFER TO DETAILED INSTRUCTIONS FOR SPECIFIC RAILING CONFIGURATIONS.
A.Trex® SignatureTM top rail and crowned cover
J.Trex® SignatureTM crossover post*
- 6' (actual length 73.5" [186.7 cm])
- 36" (actual length 34.5" [87.6 cm])
- 8' (actual length 97.5" [247.7 cm])
- 42" (actual length 40.5" [102.9 cm])
B.Trex® SignatureTM bottom rail and flat cover
K.Trex® SignatureTM post cap or post sleeve cap*
- 6' Rail (actual length 71.5" [181.6 cm])
L. Trex decking
- 6' Cover (actual length 70.0" [177.8 cm])
M. Trex Fascia
- 8' Rail (actual length 95.5" [242.6 cm])
N.Code-approved wood joist 2" x 8"
- 8' Cover (actual length 94.0" [238.8 cm])
(5.1 cm x 20.3 cm) or larger
C. Trex® SignatureTM upper rail bracket and cover
O.Code-approved wood rim joist 2" x 8"
D. Trex® SignatureTM lower rail bracket and cover
(5.1 cm x 20.3 cm) or larger
E. Trex® SignatureTM balusters (square or round)
P. Crossover bracket cover (supplied with crossover post)
F. Trex® SignatureTM center baluster (square or round) G.Trex® SignatureTM foot block** H. Trex® SignatureTM post skirt or post sleeve skirt* I.Trex® SignatureTM post*
- 36" (actual length 37" [94.0 cm]) - 42" (actual length 43" [109.2 cm]) or Trex post sleeve*** - 36" (actual length 39" [99.1 cm])
* Item not included in Trex® SignatureTM Railing kits. ** Required ONLY for All Clear Span Applications over 6' (1.83 m)
when smaller fixed baluster is fully centered, or unsupported spans greater than 5' (1.52 m) (example: 8' (2.44 m) span cut into one 5' (1.52 m) span and one 3' (0.91 m) span would require foot block under 5' (1.52 m) span since smaller fixed baluster is no longer centered). Included with 8' (2.44 m) railing kits. ***B oth 4" x 4" (10.2 cm x 10.2 cm) and 6" x 6" (15.2 cm x 15.2 cm) post sleeves are designed to fit over 4" x 4" pressure-treated post.
- 42" (actual length 45" [114.3 cm])
NOTE: MUST USE TREX DECK MOUNT POST HARDWARE
AND METAL PLATE WHEN ATTACHING TREX® SIGNATURETM
74
POSTS.
NOTE: If installing 42" (106.7 cm) railing, and using pressure-treated posts with Trex post sleeves, ensure that a longer pressure-treated post is used along with longer post sleeve, both cut to a height of 46" (116.8 cm) from decking surface.
TREX® SIGNATURETM RAILING
INSTALLING TREX® SIGNATURETM POSTS AND/OR TREX® SIGNATURETM CROSSOVER POSTS ON WOOD OR CONCRETE
IMPORTANT NOTES: »EACH POST MUST BE ATTACHED AS SHOWN TO ENSURE A CODE-
COMPLIANT AND SAFE INSTALLATION. »TREX® SIGNATURETM POSTS CANNOT BE USED WITH TREX®
SIGNATURETM TRADITIONAL OR TREX® SIGNATURETM COCKTAIL DESIGNS, ONLY PRESSURE-TREATED POST/POST SLEEVES CAN BE USED. REFER TO DETAILED INSTRUCTIONS FOR MORE INFORMATION. »ALWAYS refer to your local building code official prior to installing any railing system to ensure all code and safety requirements are met. Trex cannot be held responsible for improper or non-recommended installations. »When installing Trex® SignatureTM posts on ACQ, CCA or concrete surfaces, use an appropriate isolation barrier between post and surface (contact local building code official if needed). » For installing Trex® SignatureTM Post and/or Trex® SignatureTM Crossover Posts, see below. »For pressure-treated posts, post sleeves, and skirts, see detailed instructions provided with Trex® SignatureTM Railing Kits. » All Trex® SignatureTM stair installations require the use of a 53" (1346 mm) stair post, measured and cut to appropriate length if necessary. » If crossover stair post is required, use stair post (again cut to appropriate length if necessary) and use swivel crossover bracket. »If installing on concrete, make sure all surfaces are level.
TOOLS AND MATERIALS NEEDED
» Drill and/or screw gun (hammer drill for concrete) » 1/2" (13 mm) drill bit for wood, 3/8" (10 mm) drill bit for concrete » Blocking 2" x 8" (51 mm x 203 mm) pressure-treated Southern
Yellow Pine or equivalent
» Qty: 36 (per post) 3" pressure-treated compatible wood screws
CODE APPROVED POST APPLICATIONS
POST SIZE
2.5" (64 mm) 2.5" (64 mm)
2.5 x 2.5 (64 mm x 64 mm) Post (IRC)
< 30" height decking Acceptable (Code Approval not Applicable)
IRC Compliant
Yes
IBC Compliant
No
2
Blocking boards
2. Install two 2" x 8" (51 mm x 203 mm) boards as blocking under post location. Securely attach blocking using a total of 24 3" (76 mm) pressuretreated compatible screws (not provided).
NOTE: TO ENSURE THE BLOCKING IS FULLY SECURE, USE THE AMOUNT OF SCREWS indicated ABOVE.
TIP: Use two additional screws to "sandwich" blocking boards together for easier attachment to framing.
Line Post Installation
3
Cross bracing frame
7(-118/4.4" cm)
Cross bracing frame
Installing Trex® SignatureTM Posts and/or Trex® SignatureTM Crossover Posts on Pressure-Treated Wood Framing (Corner Post Installation)
1
2" x 8" Pressure-treated
Cross bracing frame
7(-118/.44"cm)
3. Install two 2" x 8" (51 mm x 203 mm) cross bracing frames in between joists at 7-1/4" (184 mm). Attach a total of twelve 3" (76 mm) pressure-treated compatible screws (not provided).
4
Blocking boards
TREX® SIGNATURETM RAILING
1. Install 2" x 8" (51 mm x 203 mm) cross bracing
4. Install two 2" x 8" (51 mm x 203 mm) boards as
frame in between joists at 7-1/4" (184 mm). Attach
blocking under post location. Securely attach
a total of twelve 3" (76 mm) pressure-treated
blocking using a total of twenty-four 3" (76 mm)
compatible screws (not provided).
pressure- treated compatible screws
(not provided).
75
INSTALLING TREX® SIGNATURETM POSTS AND/OR TREX® SIGNATURETM CROSSOVER POSTS ON WOOD OR CONCRETE/CONTINUED
NOTES: » Metal backplate is only required for 2.5" (64 mm)
post in IRC installations. (Consult local code official for more information.)
5
6
INSTALLING PRESSURE-TREATED POSTS,
POST SLEEVES, AND SKIRTS TO USE WITH
TREX® SIGNATURETM
RAILING
1
1.Attach posts using 1/2"
(13 mm) carriage bolts.
» Minimum joist size is 2" x 8" (51 mm x 203 mm).
» Top bolts must be 1"
2" x 8" (51 mm x 203 mm)
min.
1" (25 mm) min.
(25 mm) from top of
5-1/8" (130 mm) min.
joists.
» Bottom bolts must be
5-1/8" (130 mm) from top
bolts.
NOTE: Blocking can be added for extra strength.
5. Using post a template, mark locations of holes. 6. D rill through decking and blocking boards using
5/8" diameter bit (long drill bit will be required).
7.Insert the (2) stainless
7
steel barrier strips
under the mounting
bolt holes. BARRIER
STRIPS ARE REQUIRED
ONLY IF ATTACHING
POST DIRECTLY TO
PRESSURE TREATED
FRAMING.
barrier
8.Attach posts using four 8
3/8" x 6" (10 mm x 152 mm) hex cap bolts, washers, and nuts, along with aluminum back plate on underside of blocking. If the project requires IRC compliance, this back plate MUST be installed under the decking to ensure this will meet code compliance. Reference SKU part number ALPOSTHWDECK for required hardware and aluminum plate. (Consult local code official for more information on IRC Compliance.)
2. Slide post sleeve skirt
2
over post and down to
rest on decking surface.
Slide post sleeve over
2
post and position inside
1
post sleeve skirt.
NOTE: Shims can be used to plumb post sleeves.
Installing Trex® SignatureTM Posts on Concrete Pre-Drilled Holes
1
3/8" (10 mm)
1. Using post as a template, mark locations of the four holes and drill into concrete at least 2-5/8" (67 mm) using a 3/8" (10 mm) masonry bit.
NOTE: You can either set drill bit to correct depth on drill or mark drill bit with tape at required dimension to ensure all holes are drilled at correct depth.
2. Clean out holes to remove all concrete dust using a shop vacuum or other appropriate tool.
TREX® SIGNATURETM RAILING
76 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
INSTALLING TREX® SIGNATURETM POSTS AND/OR TREX® SIGNATURETM CROSSOVER POSTS ON WOOD OR CONCRETE/CONTINUED
3
3. Insert (2) stainless steel barrier strips under
mounting bolt holes. Use appropriate shims if
posts are not plumb. Attach posts using four
TREX SUPPLIED 3/8" x 3-3/4" (10 mm x 95 mm)
wedge anchors. Reference SKU part number
ALPOSTHWCONC for required hardware (wedge
anchors, washers, and nuts).
Barrier
NOTES: » When using hammer to tap anchors in place, keep
threaded nut at top of anchor in order to not damage threads. » Recommended torque for anchors is 20 ft-lbs.
TREX® SIGNATURETM
RAILING CONFIGURATIONS
Standard
B A
D C
Cutting posts/post sleeves is NOT required. A. Trex® SignatureTM post, pressure-treated post or Trex Post Mounts* with Trex
Transcend post sleeves, or Trex Joist Mount Posts* B. Trex® SignatureTM top rail C. Trex® SignatureTM bottom rail D. Trex® SignatureTM balusters See page 79 for "How to Install Standard Railing".
*NOTE: See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing.
Cocktail
B F
E
C A
D
Post sleeves will need to be cut. A. Pressure-treated post with Trex Transcend post sleeve
NOTE: » O nly for use with 4" x 4" (102 mm x 102 mm) post sleeve. » Trex® SignatureTM Posts, Trex Post Mounts or Joist Mount Posts cannot be used with Trex® SignatureTM Cocktail design.
B. Deck board top rail. Note: Contour and Escapes cannot be used. C. Trex® SignatureTM top rail D. Trex® SignatureTM bottom rail E. Trex® SignatureTM balusters F. Trex® SignatureTM Cocktail Rail Bracket** See page 91 for "How to Install Signature Cocktail Railing".
POST SLEEVES
WILL NEED TO BE CUT
TREX® SIGNATURETM RAILING
Traditional
B F
E
C A
D
Cutting posts/post sleeves is Not required. A. Pressure-treated post with Trex Transcend post sleeve
NOTE: » Only for use with 4" x 4" (102 mm x 102 mm) or 6" x 6" (152 mm x 152 mm) post sleeve
» Trex® SignatureTM Posts, Trex Post Mounts or Joist Mount Posts cannot be used with Trex® SignatureTM Traditional design
B. 2" x 4" (51 mm x 102 mm) lateral top rail C. Trex® SignatureTM top rail D. Trex® SignatureTM bottom rail E. Trex® SignatureTM balusters F. Trex® SignatureTM Cocktail Rail Bracket** See page 92 for "How to Install Trex® SignatureTM Traditional Railing".
** Trex® SignatureTM Cocktail Rail brackets (sold separately) are for use with either Trex® SignatureTM Traditional or Trex® SignatureTM Cocktail
designs. For a 6' section, use 4 brackets and screws provided, for 8' section, use 5 brackets and screws provided.
77
BRACKET HARDWARE HORIZONTAL APPLICATIONS (INCLUDING HORIZONTAL SWIVEL BRACKETS)
TREX® SIGNATURETM
HORIZONTAL RAILING HARDWARE
AA. Lower rail bracket
BB. Lower rail bracket cover
AA
CC. U pper rail bracket cover
DD. Upper rail bracket
BB
CC
EE. Foot block base FF. F oot block support
FOOT BLOCK COMPONENTS EE
HORIZONTAL SWIVEL HARDWARE
GG. Swivel base HH. H orizontal swivel bracket top rail II. Horizontal swivel bracket top rail cover JJ. Horizontal swivel bracket bottom rail cover KK. Horizontal swivel bracket bottom rail LL. Swivel base cover
GG HH
II
JJ KK
DD FF LL
TREX® SIGNATURETM RAILING
78 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL RAILING
TREX® SIGNATURETM STANDARD
NOTE: FOR EASE OF INSTALLATION, IT IS RECOMMENDED THAT YOU USE THE TREX® SIGNATURETM RAIL TEMPLATES TO ATTACH BRACKETS (SOLD SEPARATELY).
Attach Brackets Using Trex® SignatureTM Posts TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. Measure 1-3/8" (3.5 cm) from top of post base plate or 1-7/8" (4.8 cm) from decking surface. Mark with light line.
1
1-3/8" (3.5 cm)
2-1/2" Post
Attach Brackets Using Pressure-Treated Posts and Post Sleeves TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. M easure 1-7/8" (4.8 cm) up from deck surface to bottom of bracket. Slide skirt up to allow for proper measurement. Mark with light line.
1
1-7/8" (4.8 cm)
2
33-7/16" (84.9 cm)
or 39-7/16" (100.2 cm)
3
1
2
2.Measure up from post base plate 33-7/16" (84.9 cm) for 36" (92 cm) rail height or 39-7/16" (100.2 cm) for 42" (107 cm) rail height. Mark with light line.
NOTE: If measuring from decking surface, measure up 33-15/16" (86.2 cm) for 36" (92 cm) rail height or 39-15/16" (101.4 cm) for 42" (107 cm) rail height.
3.Center lower bracket on post above the marked
line and attach
using two self-
4
tapping screws
(provided).
4.Center upper
1
bracket on post
above marked line
and attach using
2
(3) self-tapping
screws (provided).
NOTE: Upper bracket is not required on crossover post configuration.
2
33-15/16" (86.2 cm)
or 39-15/16" (101.4 cm)
3
1
2
2.Measure up from decking surface 33-15/16" (862 cm) for 36" (92 cm) rail height or 39-15/16" (101.4 cm) for 42" (107 cm) rail height. Mark with light line.
NOTE: Push skirt back down onto surface of decking BEFORE ATTACHING BRACKETS.
3.Center lower bracket on post above the marked
line and attach using two 2" (51 mm) wood
screws (provided).
4.C enter upper bracket 4
on post above marked
line and attach using
three 2" (51 cm) wood
1
screws (provided).
2
TREX® SIGNATURETM RAILING
79 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL RAILING POST TO POST
TREX® SIGNATURETM
NOTES:
» TREX® SIGNATURETM RAILINGS ARE DESIGNED TO BE ATTACHED WITH POSTS INSTALLED AT A CLEAR SPAN OF 6' (1.83 M) OR 8' (2.44 M).
» IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING POST-TO-POST CONFIGURATION, THE BOTTOM RAIL WILL NOT NEED TO BE CUT, BUT THE TOP RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT.
» FOR ODD SPAN LENGTHS, BOTH TOP RAIL AND BOTTOM RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT. ENSURE THAT BALUSTERS ARE SPACED WITH AN EQUAL DISTANCE ON EACH SIDE OF THE POST.
» WHEN RAILINGS ARE CUT TO ODD SPANS, ALL SPANS GREATER THAN 5' (1.52 M) (EXAMPLE: 8' (2.44 M) SPAN CUT INTO ONE 5' (1.52 M) SPAN AND ONE 3' (0.91 M) SPAN) WOULD REQUIRE FOOT BLOCK UNDER 5' (1.52 M) SPAN SINCE SMALLER FIXED BALUSTER IS NO LONGER CENTERED.
Cutting Bottom Rail and Bottom Rail Cover
KEYKEY
2
Mark
Cut
1/4" (0.6 cm)
Bottom rail
1/4" (0.6 cm)
2.Cut each end of bottom rail 1/4" (0.6 cm) shorter than mark on each end to allow for fit into bottom rail brackets.
3
Bottom rail
How to Measure and Cut Bottom and Top Railings (When Required)
3/4" (1.9 cm)
3/4" (1.9 cm)
1
3.Slide rail insert out and cut 3/4" (19 mm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
Bottom rail Top rail
Center slot for fixed baluster
4. M ark and cut bottom rail cover 1-1/2" (38 mm) shorter than bottom rail.
1.Position bottom and top rails between posts and align with bottom bracket. Align the center baluster slot in both rails with the middle of the span between posts.* This will allow an equal number of baluster holes on each side of center slot. Mark bottom rail and top rail at each end (ensure both rails are centered between posts).
* In some cases, due to odd railing spans, the center baluster may need to be offset in one direction to ensure there is enough room at both post locations for balusters to be placed. Review this BEFORE cutting any railings to ensure all balusters are equally spaced.
80
4
Bottom rail
Bottom rail cover
1-1/2" (3.8 cm)
TREX® SIGNATURETM RAILING
HOW TO INSTALL HORIZONTAL RAILING POST TO POST/CONTINUED
TREX® SIGNATURETM
Cutting Top Rail
KEYKEY
5
Mark
Cut
Standard post
Standard post
Attaching Center Baluster to Bottom Rail
Center balluster slot
8
Top rail
Inverted Bottom view
1/4" (0.6 cm)
1/4"
(0.6 cm)
2
1
5. Cut each end of top rail 1/4" (0.6 cm) shorter than mark to allow for fit into top rail brackets.
Cutting Top Rail Insert and Cover
6
3/4" (1.9 cm)
Top rail
3/4" (1.9 cm)
8.Attach shorter, center baluster in center slot in bottom rail using two #8 x 1-1/4" (3.2 cm) screws (provided).
Attaching Bottom Rail Cover and Bottom Rail to Brackets
9 2
Lorem ipsum
1
6.Slide rail insert out and cut 3/4" (1.9 cm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
7.Mark and cut top rail
7
cover same length as
top rail for all top rail
configurations.
3
9.Attach "flat" bottom rail cover to bottom rail by first centering cover on bottom rail (this will allow gap on each end of bottom rail for placement into brackets). Align cover on one side of bottom rail in slot on side of rail. Then starting from one end of rail snap cover onto opposing slot working down the length of rail. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
TREX® SIGNATURETM RAILING
81 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL RAILING POST TO POST/CONTINUED
TREX® SIGNATURETM
Attach Upper Railings
10
1/2"
11
13
(1.3 cm)
1
2
1
1
2
1
7/64"
(.28 cm)
10.S et bottom rail into bottom brackets. Tabs on brackets will be inside of bottom rail (not shown when railing is attached). To ensure fit into tab, measure and mark 1/2" (1.3 cm) out from side of post.
11.Attach bottom rail to bottom bracket by fastening through marked measurement on top of rail into tab on bottom bracket using one self-tapping screw each side (provided).
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
Installing Remaining Balusters into Bottom Rail
12
2
13. W orking from one end of upper rail, snap balusters
into upper rail working down length of rail. Fasten
center baluster into center slot using two #8 x 1-1/4"
(3.2 cm) screws (provided).
14. F asten upper rail to each
bracket by installing
14
screws diagonally
through upper rail into
bracket using two self-
2
tapping screws each
side (provided).
7/64" 1 (.28 cm)
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
15 2 1
TREX® SIGRNAAITLIUNREGTM RAILING
12. Place remaining balusters into holes in lower rail by snapping fully into place. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
3
15.A ttach "crowned" upper rail cover to upper rail by aligning cover on one side of rail. Then starting from one end of rail, snap cover onto opposing slot working down length of rail. GENTLE tapping with a rubber mallet may facilitate fastening.
82
HOW TO INSTALL HORIZONTAL RAILING POST TO POST/CONTINUED
TREX® SIGNATURETM
Attachment of Bracket Covers, Skirts, and Caps
16
1
17
Trex® SignatureTM
post
1
2 2
16.A ttach corresponding bracket covers over opening in upper and bottom rails.
17.Attach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
18
19
1
Trex® SignatureTM post
2 Post sleeve
1
3
18. A ttach post caps to Trex® SignatureTM posts. (Use of rubber .mallet may be required for secure attachment.)
19.A ttach post caps to post sleeves using external grade PVC construction adhesive.
20. Attachment of Foot Block See instructions on page 97.
HOW TO INSTALL HORIZONTAL RAILING POST TO CROSSOVER POST
TREX® SIGNATURETM
NOTES:
» TREX® SIGNATURETM RAILINGS ARE DESIGNED TO BE ATTACHED WITH POSTS INSTALLED AT A CLEAR SPAN OF 6' (1.83 M) OR 8' (2.44 M).
» IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING POST-TO-CROSSOVER POST CONFIGURATION, THE BOTTOM RAIL WILL NOT NEED TO BE CUT, BUT THE TOP RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT.
» AT ALL FINAL END POST CONFIGURATIONS, TOP RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT.
» FOR ODD SPAN LENGTHS, BOTH TOP RAIL AND BOTTOM RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT. ENSURE THAT BALUSTERS ARE SPACED WITH AN EQUAL DISTANCE ON EACH SIDE OF THE POST.
» WHEN RAILINGS ARE CUT TO ODD SPANS, ALL SPANS GREATER THAN 5' (1.52 M) (EXAMPLE: 8' (2.44 M) SPAN CUT INTO ONE 5' (1.52 M) SPAN AND ONE 3' (0.91 M) SPAN) WOULD REQUIRE FOOT BLOCK UNDER 5' (1.52 M) SPAN SINCE SMALLER FIXED BALUSTER IS NO LONGER CENTERED.
How to Measure, Mark and Cut Bottom and Top Railings (When Required)
1
Bottom rail Top rail
Center slot for fixed baluster
Important: DO NOT cut top rail the same length as bottom rail.
1.Position bottom and top rails between posts and align with bottom bracket. Align the center baluster slot in both rails with the middle of the span between posts.* This will allow an equal number of baluster holes on each side of center slot. Mark bottom rail and top rail at each end (ensure both rails are centered between posts).
* In some cases, due to odd railing spans, the center baluster may need to be offset in one direction to ensure there is enough room at both post locations for balusters to be placed. Review this BEFORE cutting any railings to ensure all balusters are equally spaced.
TREX® SIGRNAAITLUINRGETM RAILING
83 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL RAILING POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
KEYKEY
2
Mark
Cut
Cutting Top Rail
KEYKEY
5
Mark
Cut
Standard post
Crossover post
Bottom rail
Top rail
1/4" (0.6 cm)
1/4" (0.6 cm)
1/4" (0.6 cm)
3/4" (1.9 cm)
Cutting Bottom Rail and Bottom Rail Cover ONLY 2.Cut each end of bottom rail 1/4" (0.6 cm) shorter
than mark on each end to allow for fit into bottom
3
5. T op rail must be cut differently on each side of the rail. Railing side that attaches to standard post should be cut 1/4" (0.6 cm) shorter than the mark to allow for fit into top rail bracket. Railing side that attaches to the crossover post should be cut 3/4" (1.9 cm) LONGER than the mark to allow for fit into the crossover post bracket.
3/4" (1.9 cm)
Bottom rail
6
3/4" (1.9 cm)
Top rail
rail brackets.
3.Slide rail insert out and cut 3/4" (1.9 cm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
4. M ark and cut bottom
4
Bottom rail
rail cover 1-1/2"
(3.8 cm) shorter than
bottom rail.
Bottom rail cover
1-1/2" (3.8 cm)
3/4" (1.9 cm)
3/4" (1.9 cm)
Cutting Top Rail Insert and Cover
6.Slide rail insert out and cut 3/4" (1.9 cm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
7.Mark and cut top rail
7
cover same length as
top rail for all top rail
configurations.
TREX® SIGRNAAITLIUNREGTM RAILING
84
HOW TO INSTALL HORIZONTAL RAILING POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
Attaching Center Baluster to Bottom Rail
Center balluster slot
8
10
1/2" (1.3 cm)
11
2
Inverted Bottom view
2
1
8.Attach shorter, center baluster in center slot in bottom rail using two #8 x 1-1/4" (3.2 cm) screws (provided).
Attaching Bottom Rail Cover and Bottom Rail to Brackets
1
2
7/64" 1
(.28 cm)
10.S et bottom rail into bottom brackets. Tabs on brackets will be inside of bottom rail (not shown when railing is attached). To ensure fit into tab, measure and mark 1/2" (1.3 cm) out from side of post.
11.Attach bottom rail to bottom bracket by fastening through marked measurement on top of rail into tab on bottom bracket using one self-tapping screw each side (provided).
9
NOTE: Pre-drilling is required (7/64" [0.28 cm]
2
drill bit) for attachment of railing to bracket.
Installing Remaining Balusters into Bottom Rail
1
12
3
9.Attach "flat" bottom rail cover to bottom rail by first centering cover on bottom rail (this will allow gap on each end of bottom rail for placement into brackets). Align cover on one side of bottom rail in slot on side of rail. Then starting from one end of rail snap cover onto opposing slot working down the length of rail. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
12. Place remaining balusters into holes in lower rail by snapping fully into place. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
TREX® SIGRNAAITLUINRGETM RAILING
85 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL RAILING POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
Attach Upper Railings
13
1 1
16 2 1
2
3
13. W orking from one end of upper rail, snap balusters
into upper rail working down length of rail. Fasten
center baluster into center slot using two #8 x 1-1/4"
(3.2 cm) screws (provided).
14. A t post location, fasten
upper rail to each
14
bracket by installing
screws diagonally
through upper rail into
2
bracket using two self-
tapping screws each
side (provided).
1 7/64"
(.28 cm)
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
15. A t crossover post
15
location, fasten upper
rail to crossover post
by installing screws
2
diagonally through
upper rail into post using
two self-tapping screws
each side (provided).
7/64" 1 (.28 cm)
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
16.A ttach "crowned" upper rail cover to upper rail by aligning cover on one side of rail. Then starting from one end of rail, snap cover onto opposing slot working down length of rail. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
Attachment of Bracket Covers, Skirts, and Caps
17
1
18 Trex®
SignatureTM post
1
2 2
17.A ttach corresponding bracket covers over opening in upper and bottom rails.
18.Attach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
19
1
Trex® SignatureTM post
20
2 Post sleeve
1
3
19. A ttach post caps to Trex® SignatureTM posts. (Use of rubber .mallet may be required for secure attachment.)
20.A ttach post caps to post sleeves using external grade PVC construction adhesive.
86
TREX® SIGRNAAITLIUNREGTM RAILING
HOW TO INSTALL HORIZONTAL RAILING POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
21.For crossover post
21
configuration, attach
crossover post cap to
crossover post.
22.A ttachment of Foot Block See instruction on page 97.
HOW TO INSTALL HORIZONTAL RAILING CROSSOVER POST TO CROSSOVER POST
TREX® SIGNATURETM STANDARD
NOTES:
» TREX® SIGNATURETM RAILINGS ARE DESIGNED TO BE ATTACHED WITH POSTS INSTALLED AT A CLEAR SPAN OF 6' (1.83 M) OR 8' (2.44 M).
» IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING POST-TO-CROSSOVER POST CONFIGURATION, THE BOTTOM RAIL WILL NOT NEED TO BE CUT, BUT THE TOP RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT.
» FOR ODD SPAN LENGTHS, BOTH TOP RAIL AND BOTTOM RAIL WILL NEED TO BE MEASURED (MAKING SURE BALUSTERS LINE UP VERTICALLY) AND CUT. ENSURE THAT BALUSTERS ARE SPACED WITH AN EQUAL DISTANCE ON EACH SIDE OF THE POST.
» WHEN RAILINGS ARE CUT TO ODD SPANS, ALL SPANS GREATER THAN 5' (1.52 M) (EXAMPLE: 8' (2.44 M) SPAN CUT INTO ONE 5' (1.52 M) SPAN AND ONE 3' (0.91 M) SPAN) WOULD REQUIRE FOOT BLOCK UNDER 5' (1.52 M) SPAN SINCE SMALLER FIXED BALUSTER IS NO LONGER CENTERED.
How to Measure, Mark and Cut Bottom and Top Railings (When Required)
1
Bottom rail Top rail
Center slot for fixed baluster
Important: DO NOT cut top rail the same length as bottom rail.
1.Position bottom and top rails between posts and align with bottom bracket. Align the center baluster slot in both rails with the middle of the span between posts.* This will allow an equal number of baluster holes on each side of center slot. Mark bottom rail and top rail at each end (ensure both rails are centered between posts).
* In some cases, due to odd railing spans, the center baluster may need to be offset in one direction to ensure there is enough room at both post locations for balusters to be placed. Review this BEFORE cutting any railings to ensure all balusters are equally spaced.
TREX® SIGRNAAITLUINRGETM RAILING
87 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL RAILING CROSSOVER POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
Cutting Bottom Rail and Bottom Rail Cover ONLY
KEYKEY
2
Mark
Cut
Cutting Top Rail
KEYKEY
5
Mark
Cut
Crossover post
Crossover post
Bottom rail
Top rail
1/4" (0.6 cm)
1/4" (0.6 cm)
3/4" (1.9 cm)
3/4" (1.9 cm)
2.Cut each end of bottom rail 1/4" (0.6 cm) shorter than mark on each end to allow for fit into bottom rail brackets.
3
3/4" (1.9 cm)
Bottom rail
3/4" (1.9 cm)
5. Cut each end of top rail 3/4" (1.9 cm) LONGER than the mark to allow for fit into the crossover post bracket on each side.
Cutting Top Rail Insert and Cover
6
3/4" (1.9 cm)
Top rail
3/4" (1.9 cm)
3.Slide rail insert out and cut 3/4" (1.9 cm) FROM EACH SIDE of insert, then slide back inside rail and center.
4. M ark and cut bottom rail cover 1-1/2" (3.8 cm) shorter than bottom rail.
4
Bottom rail
6.Slide rail insert out and cut 3/4" (1.9 cm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
7.Mark and cut top rail
7
cover same length as
top rail for all top rail
configurations.
Bottom rail cover
1-1/2" (3.8 cm)
TREX® SIGNATURETM RAILING
88
HOW TO INSTALL HORIZONTAL RAILING CROSSOVER POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
Attaching Center Baluster to Bottom Rail
10
Center balluster slot
8
1/2" (1.3 cm)
11
2
Inverted Bottom view
1
2
7/64" 1 (.28 cm)
2
1
8.Attach shorter, center baluster in center slot in bottom rail using two #8 x 1-1/4" (3.2 cm) screws (provided).
Attaching Bottom Rail Cover and Bottom Rail to Brackets
9 2
1
10.S et bottom rail into bottom brackets. Tabs on brackets will be inside of bottom rail (not shown when railing is attached). To ensure fit into tab, measure and mark 1/2" (1.3 cm) out from side of post.
11.Attach bottom rail to bottom bracket by fastening through marked measurement on top of rail into tab on bottom bracket using one self-tapping screw each side (provided).
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
Installing Remaining Balusters into Bottom Rail
12
3
9.Attach "flat" bottom rail cover to bottom rail by first centering cover on bottom rail (this will allow gap on each end of bottom rail for placement into brackets). Align cover on one side of bottom rail in slot on side of rail. Then starting from one end of rail snap cover onto opposing slot working down the length of rail. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
12. Place remaining balusters into holes in lower rail by snapping fully into place. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
TREX® SIGNATURETM RAILING
89
HOW TO INSTALL HORIZONTAL RAILING CROSSOVER POST TO CROSSOVER POST/CONTINUED
TREX® SIGNATURETM
Attach Upper Railings
13
1 1
15 2 1
2
3
13. W orking from one end of upper rail, snap balusters into upper rail working down length of rail. Fasten center baluster into center slot using two #8 x 1-1/4" (3.2 cm) screws (provided).
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
14. A t post locations, fasten upper rail to crossover
14
post by installing screws
diagonally through
2
upper rail into post using
two self-tapping screws
each side (provided).
7/64" 1 (.28 cm)
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
15.A ttach "crowned" upper rail cover to upper rail by aligning cover on one side of rail. Then starting from one end of rail, snap cover onto opposing slot working down length of rail. GENTLE tapping with a rubber mallet may facilitate fastening.
Attachment of Bracket Covers, Skirts, and Caps
16
17
TTrreexx®SSigignnaatuturereTM
ppoosstt
2
1
2
16..Attach corresponding bracket covers over opening in bottom rails.
17.Attach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
18.Attach crossover post
cap to crossover post. 18
19. Attachment of Foot . Block. See instructions on page 97.
TREX® SIGRNAAITLIUNREGTM RAILING
90 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL TREX® SIGNATURETM COCKTAIL RAILING
TREX® SIGNATURETM
Cutting Post and Post Sleeve
2.Mark and cut post and
post sleeve measuring 2
from deck surface:
» 36-1/32" (915 mm) for
36" (914 mm) height. » 42-1/32" (1068 mm)
for 42" (1067 mm) height.
36-1/32" (915 mm)
or 42-1/32" (1068 mm)
IMPORTANT NOTE: » O NLY for use with pressure-treated 4 x 4 post (3.5"
nominal square) and 4" x 4" (102 mm x 102 mm) post sleeve. Trex® SignatureTM posts, Trex post mounts or joist mount posts cannot be used with Trex® SignatureTM Cocktail railing. Cutting post and post sleeve only apply to the Cocktail style railing.
Installing Pressure-treated Posts, Post Sleeves,and
Skirts to Use with Trex® SignatureTM Railing
1a.Attach posts using 1/2"
(13 mm) carriage bolts. 1a
» M inimum joist size is
2" x 8" (51 mm x
203 mm). » Top bolts must be 1"
(25 mm) from top of joists.
2" x 8" (51 mm x 203 mm)
min.
1" (25 mm) min.
5-1/8" (130 mm) min.
» B ottom bolts must be
5-1/8" (130 mm) from
top bolts.
NOTE: Blocking can be added for extra strength.
1b.S lide post sleeve skirt
1b
over post and down to
rest on decking surface.
Slide post sleeve over
2
post and position inside
1
post sleeve skirt.
NOTE: Shims can be used to plumb post sleeves.
3. Installing Horizontal Fixed Brackets See instructions on page 79.
4. Installing Horizontal Swivel Brackets See instructions on page 94.
5. Cutting Railings for Horizontal Fixed Brackets See instructions on page 80 - Post-to-Post, page 83 Post-to-Crossover Post, or page 87 - Crossover Postto-Crossover Post.
6. Cutting Railings for Horizontal Swivel .Brackets See instructions on page 95.
7. Attaching Center Baluster to Bottom Rail See instructions on page 81 - Post-to-Post, page 85 Post-to-Crossover Post, or page 89 - Crossover Post-toCrossover Post.
8. Attaching Bottom Rail Cover and Bottom Rail to Brackets See instructions on page 81 - Post-to-Post, page 85 Post-to-Crossover Post, or page 89 - Crossover Post-toCrossover Post.
9. Installing Remaining Balusters into .Bottom Rail See instructions on page 82 Post-to-Post, page 85 Post-to-Crossover Post, or page 89 - Crossover Post-toCrossover Post.
10. Attaching Top Rail and Top Rail Cover See instructions on page 82 - Post-to-Post, page 86Post-to-.Crossover Post, or page 90 - Crossover Post-toCrossover Post.
NOTE: Top Bracket Covers are not attached in this configuration.
11. A ttaching Deck Board to Top Rail
Place deck boards
(DO NOT use Escapes
11
or Contour deck boards
1
for top rail) over top
1
rails. Attach boards
on each post with
Trex-recommended
composite screws
2
(quantity of 2 per each
board end).
TREX® SIGRNAAITLUINRGETM RAILING
91
HOW TO INSTALL TREX® SIGNATURETM COCKTAIL RAILING/CONTINUED
TREX® SIGNATURETM
12.Secure boards
12
to top rail using
Trex® SignatureTM
Cocktail Bracket
1
(sold separately).
Ensure that there is a
bracket at each end
of the railing section,
2
then space brackets
approximately every
24" and attach with
4 screws provided.
NOTE: Pre-drilling before attachment is recommended.
13.U se scarf cut for posts 13
where two deck boards meet.
NOTES: » L eave 1/8" (3 mm) gap
between deck boards. » D eck boards can
overhang end of last post maximum 1/2" (13 mm).
14. A ttachment of Bottom Bracket Covers and Skirts See instructions on page 86.
15. A ttachment of Foot Block See instructions on page 97.
HOW TO INSTALL TREX® SIGNATURETM TRADITIONAL RAILING
TREX® SIGNATURETM
Important: Only use for use with pressure-treated 4 x 4 post (3.5" nominal square) and 4" x 4" (102 mm x 102 mm) or 6" x 6" post sleeve. Trex® SignatureTM Posts, Trex Post Mounts or Joist Mount Posts cannot be used with Trex® SignatureTM Traditional railing.
1. Installing Posts, Post Sleeve Skirts and Post Sleeves See instructions on page 76.
2. Installing Horizontal Fixed Brackets See instructions on page 79.
3. Installing Horizontal Swivel Brackets See instructions on page 94.
4.Cutting Railings for Horizontal Fixed Brackets See instructions on page 80 Post-to-Post, page 83 Post-to-Crossover Post, or page 87 Crossover Postto-Crossover Post.
5. Cutting Railings for Horizontal Swivel Brackets See instructions on page 95.
6. Attaching Center Baluster to Bottom Rail See instructions on page 81 Post to-Post, 85 Post-toCrossover Post, or 89 Crossover Post-to-Crossover Post.
7. Attaching Bottom Rail Cover and Bottom Rail to Brackets See instructions on page 81 Post-to-Post, 85 Post-toCrossover Post, or 89 Crossover Post-to-Crossover Post.
8. Installing Remaining Balusters into .Bottom Rail See instructions on page 81 Post-to-Post, 85 Post-toCrossover Post, or 89 Crossover Post-to-Crossover Post.
9. Attaching Top Rail and Top Rail Cover See instructions on page 81 Post-to-Post, 86 Post-toCrossover Post, or 90 Crossover Post-to-Crossover Post.
NOTE: Top Bracket Covers
are not attached in this
10
configuration.
10. A ttaching 2" x 4"
(51 mm x 102 mm)
to Top Rail
1
Measure between
posts and cut 2" x 4"
(51 mm x 102 mm)
to length.
TREX® SIGNATURETM RAILING
92
HOW TO INSTALL TREX® SIGNATURETM TRADITIONAL RAILING/CONTINUED
TREX® SIGNATURETM
11.Place 2" x 4" (51 mm
11
x 102 mm) on Trex®
SignatureTM top rail.
1 1
13. Pre-drill a pilot hole .Pre-d1r3ill a pilot hole
and toenail 2-1/2" (6.4 cm) screw at each end of 2" x 4" (5.1 cm x 10.2 cm) into post on back side of rail (side not facing decking).
12.Secure 2" x 4" (51 mm 12
x 102 mm) to top rail
using Trex® SignatureTM
Cocktail Bracket (sold
separately). Ensure that
1
there is a bracket at
each end of the railing
section, then space
2
brackets approximately
every 24" and attach
with 4 screws provided.
NOTE: Pre-drilling before attachment is recommended.
14.A ttachment of Bottom Rail Bracket Covers and Caps See instructions on page 83.
15.Attachment of Foot Block See instructions on page 97.
TREX® SIGNATURETM RAILING
93
INSTALLATION OF HORIZONTAL SWIVEL BRACKETS
TREX® SIGNATURETM STANDARD
Attach Swivel Brackets Base Using Trex® SignatureTM Posts TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. Measure 1-3/8" (3.5 cm) from top of post base plate or 1-7/8" (4.8 cm) from decking surface. Mark with light line.
1
1-3/8" (3.5 cm)
2-1/2" Post
Attach Swivel Brackets Using Pressure-treated Posts and Post Sleeves TIP: Use a clamp to help hold brackets in place while fastening with screws
1
2
1-7/8"
1
(4.8 cm)
2
2
1
2
3
32-5/16" (82.0 cm)
or 38-5/16" (97.3 cm)
2.Center lower bracket on post above the marked
line and attach using four self-tapping screws
(provided).
3.Measure up 32-5/16" (82.0 cm) for 36" (91.4 cm)
tall railing or 38-5/16" (97.3 cm) for 42"
(106.7 cm) tall railing from top of lower rail
bracket. Mark with a light line.
4.Center upper
bracket on post
4
below marked line
and attach using
1
four self-tapping
screws (provided).
NOTE: Upper bracket
2
is not required on
crossover post
configuration.
1.Measure 1-7/8" (4.8 cm) up from deck surface to bottom of bracket. Slide skirt up to allow for proper measurement, then push skirt back down onto surface of decking BEFORE ATTACHING BRACKET. Mark with light line.
2.Center lower bracket on post above the marked line and attach using four 2" (5.1 cm) wood screws (provided).
3
32-5/16" (82.0 cm)
or 38-5/16" (97.3 cm)
4
1
2
3. Measure up 32-5/16" (82.0 cm) for 36" (91.4 cm) tall railing or 38-5/16" (97.3 cm) for 42" (106.7 cm) tall railing from top of lower rail bracket. Mark with a light line.
4.Center upper bracket on post below marked line and attach using four 2" (5.1 cm) wood screws (provided).
TREX® SIGNATURETM RAILING
94 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
INSTALLATION OF HORIZONTAL SWIVEL RAILING
TREX® SIGNATURETM STANDARD
NOTES:
» WHEN USING TREX® SIGNATURETM HORIZONTAL SWIVEL BRACKETS, BOTH BOTTOM AND TOP RAILS WILL NEED TO BE MEASURED AND CUT TO APPROPRIATE LENGTHS.
» HORIZONTAL SWIVEL BRACKETS CAN BE USED UP TO A 50° ANGLE FOR TREX® SIGNATURETM RAILINGS.
» WHEN USING HORIZONTAL SWIVEL BRACKETS VERY IMPORTANT TO LAY OUT LOCATION AND ORIENTATION OF POSTS AND SWIVEL BRACKETS BEFORE INSTALLING SWIVEL BRACKETS.
» WHEN RAILINGS ARE CUT TO ODD SPANS, ALL SPANS GREATER THAN 5' (1.52 M) (EXAMPLE: 8' (2.44 M) SPAN CUT INTO ONE 5' (1.52 M) SPAN AND ONE 3' (0.91 M) SPAN) WOULD REQUIRE FOOT BLOCK UNDER 5' (1.52 M) SPAN SINCE SMALLER FIXED BALUSTER IS NO LONGER CENTERED.
Cutting Bottom Rail and Bottom Rail Cover
2
Bottom rail
How to Measure and Cut Bottom and Top Railings
1
2.Cut bottom rail to the measurement between the
bottom swivel brackets.
3
Center slot for fixed baluster
1.With brackets in correct swivel location, measure distance from inside of bracket to inside of bracket. ENSURE THAT BEFORE CUTTING, BALUSTERS HOLES ON BOTH BOTTOM AND TOP RAIL LINE UP. ALSO MAKE SURE CENTER BALUSTER SLOT IS AS CLOSE TO THE MIDDLE OF THE SPAN AS POSSIBLE. In some cases, due to odd railing spans, the center baluster may need to be offset in one or the other direction to ensure there is enough room at both post locations for balusters to be placed.
3/4" (1.9 cm)
Bottom rail
3/4" (1.9 cm)
3.Slide rail insert out and cut 3/4" (1.9 cm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
4. M ark and cut bottom rail cover 1-1/2"
4
Bottom rail
(3.8 cm) shorter than
bottom rail.
Bottom rail cover
1-1/2" (3.8 cm)
TREX® SIGNATURETM RAILING
95
INSTALLATION OF HORIZONTAL SWIVEL RAILING/CONTINUED
TREX® SIGNATURETM STANDARD
Cutting Top Rail Option 1: For Post-to-Post Configuration
5a
KEYKEY Mark Cut
Standard post
Standard post
Cutting Top Rail Insert and Cover
6
Top rail
1/4" (0.6 cm)
Top rail
1/4" (0.6 cm)
3/4" (1.9 cm)
3/4" (1.9 cm)
5a. C ut top rail to the measurement between the top swivel brackets. For standard post-to-standard post configurations this would be same dimensions as that of the bottom rail.
Cutting Top Rail Option 2: For Post-to-Crossover Post Configuration
5b
Standard post
Crossover post
5b. W hen going from standard-post to crossover post, measurement must be taken from inside of top horizontal swivel bracket to inside lip of crossover bracket (which is attached to top of crossover post).
6.Slide rail insert out and cut 3/4" (1.9 cm) FROM
EACH SIDE of insert, then slide back inside rail
and center.
7.Mark and cut top rail
7
cover same length as
top rail for all top rail
configurations.
8.Attaching Center Baluster to Bottom Rail See instructions on page 82 Post-to-Post or 85 Post-toCrossover Post.
9.Attaching Bottom Rail Cover and Bottom Rail to Brackets See instructions on page 81 Post-to-Post or 85 Post-toCrossover Post.
10. Installing Remaining Balusters into Bottom Rail See instructions on page 82 Post-to-Post or 85 Post-toCrossover Post.
11.Attach Upper Railings See instructions on page 82 Post-to-Post or 86 Post-toCrossover Post.
12. Attachment of Bracket Covers, Skirts, and Caps See instructions on page 83 Post-to-Post or 86 Post-toCrossover Post.
13.A ttachment of Foot Block See instructions on page 97.
TREX® SIGNATURETM RAILING
96 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL FOOT BLOCKSHORIZONTAL RAILING
TREX® SIGNATURETM
Attachment of Foot Block (Required ONLY for All Clear Span Applications Over 6' [1.83 m])
1
1
2. P lace base (smaller
side facing down) on
2
decking surface. Attach
base of foot block using
one screw at an angle
through base and into
decking.
2
1. T o ensure correct location, place foot block under center of bottom rail. Mark to provide placement location of base.
NOTE: Pre-drilling is recommended (1/8" [0.32 cm] drill bit) for attachment of base.
3. A fter attached, use a rubber mallet along
3
with scrap piece of
wood to tap foot block
until it locks into place. 1
TREX® SIGNATURETM RAILING
97 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
BRACKET HARDWARE STAIR APPLICATIONS (INCLUDING STAIR SWIVEL BRACKETS, STAIR CROSSOVER BRACKET, AND COMPOUND SWIVEL BRACKETS)
TREX® SIGNATURETM
FIXED BRACKET STAIR HARDWARE
AA. B ottom Stair Bracket and Cover Lower Rail
BB. T op Stair Bracket and Cover Lower Rail
CC. Fastener Pack DD. B ottom Stair Bracket and
Cover Upper Rail EE. Top Stair Bracket and
Cover Upper Rail
AA
DD
BB
SWIVEL BRACKET STAIR HARDWARE
FF. Swivel Top Rail Bracket and Cover Stair
FF
GG. Swivel Bottom Rail Bracket and Cover Stair
HH. Fastener Covers
II. Fastener Pack
EE
HH GG
MM
COMPOUND SWIVEL BRACKET STAIR HARDWARE
JJ.Compound Swivel Top Rail Bracket and Cover Stair
KK. Compound Swivel Bottom Rail Bracket and Cover Stair
LL. Fastener Covers MM. Fastener Pack
JJ MM
LL KK
TREX® SIGNATURETM RAILING
SWIVEL CROSSOVER BRACKET KIT STAIR HARDWARE
NN. Swivel Crossover Bracket Stair
OO. Post-to-Bracket Fasteners
NN
OO
98
HOW TO INSTALL TREX® SIGNATURETM STAIR POSTS AND STAIR RAILING
TREX® SIGNATURETM
IMPORTANT NOTES: » T REX® SIGNATURETM POSTS CANNOT BE USED
WITH TREX® SIGNATURETM TRADITIONAL OR TREX® SIGNATURETM COCKTAIL STAIR DESIGNS, ONLY PRESSURE-TREATED POST/POST SLEEVES CAN BE USED. REFER TO DETAILED INSTRUCTIONS FOR MORE INFORMATION. » A ll Trex® SignatureTM stair installations require the use of 53" (134.6 CM) stair post, measured and cut to appropriate length if required. » If crossover stair post is required, use stair post (again cut to appropriate length if required) and use swivel crossover bracket. » Trex® SignatureTM Stair fixed brackets are designed to work only with stair slopes of 32°-37°. » F or smaller (less than 32°) or larger angles (greater than 37°), use the Trex® SignatureTM Stair Swivel brackets. » Trex® SignatureTM Compound swivel stair brackets are designed for flared stair designs. » If installing stair railings at exact span lengths of 6' (1.8 M) or 8' (2.4 M) and using post-to-post configuration, the bottom stair rail will not need to be cut*, but the top stair rail will need to be measured (making sure balusters line up vertically) and cut. » If installing stair railings at exact span lengths of 6' (1.8 M) or 8' (2.4 M), and using crossover post configuration (spans from one crossover post to another crossover post), both the bottom and top stair rails will not need to be cut* if the angle is approximately 34°. » A t all final end post configurations, top stair rail will need to be measured (making sure balusters line up vertically) and cut. » F or odd span lengths, both bottom and top stair rails will need to be measured (making sure balusters line up vertically) and cut. Also, ensure that balusters are spaced with equal distance on each side of the post. » Rails that do not require cutting must be oriented in the correct direction to .ensure balusters are spaced properly when installed in brackets. On both bottom and top stair railings, baluster hole closest to the end of the each stair rail is to be installed at the top of the stair section. Ensure that both bottom and top rails are correct and balusters line up vertically before INSTALLING.
Installing Standard Trex® SignatureTM Stair Posts, Trex® SignatureTM Stair Crossover Posts, or Pressuretreated Post, Post Sleeves and Skirts
1.Make sure 53" (135.6 cm) posts are used for all stair posts.
2.If Trex® SignatureTM stair
2
posts are used, install
at nose of stair tread
directly under required
blocking. See Trex®
SignatureTM horizontal
post instructions on page
79 for details.
3.If pressure-treated post/ 3
post sleeves are used, posts are to be installed to the inside of the last stair stringer (rails must be over decking surface). See pressure-treated post instructions on page 79 for details.
TREX® SIGNATURETM RAILING
99 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ATTACHING FIXED STAIR BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES
TREX® SIGNATURETM
NOTES: » A ll Trex® SignatureTM fixed stair brackets work ONLY
with stair slopes of 32°-37°. » Illustrations shown are representations when using
Trex® SignatureTM post, but same rules apply if using pressure-treated posts and post sleeves. » U se a clamp to help hold stair brackets in place while fastening with screws.
IMPORTANT NOTE: » BEFORE ATTACHING ANY UPPER BRACKETS MAKE SURE PROPER RAILING HEIGHTS ARE ACHIEVED. RAILING HEIGHTS AND UPPER BRACKET HEIGHTS MAY NEED TO BE ADJUSTED, HOWEVER, DO NOT REDUCE HEIGHTS BASED ON YOUR RAILING CODE REQUIREMENTS. MEASURE CAREFULLY AS DIMENSION HEIGHTS MAY NEED TO BE ADJUSTED!
1
attach the stair bracket on the lower stair post. A 90° cordless drill is recommended to attach screws in this area (if possible).
How to Measure Bottom Stair Railing (WHEN REQUIRED)
3
Top stair post
Bottom stair post
1" (2.5 cm)
1.Lay bottom stair rail on steps beside posts. Position bottom rail at least 1" (2.5 cm) above nose of stair tread.
Tip: Use a 1" (2.5 cm) deck board as a spacer board and clamp rails to post. Mark where lower brackets are to be attached to both posts. Mark at underside of railing location. Installing Lower Fixed Stair Brackets
3.Position bottom stair rail along the nose of the stair treads. Ensure that before cutting, balusters holes are centered in between the posts and also allow for clearance for attachment to brackets. On top stair post location, mark UNDERSIDE of lower rail. On bottom stair post location mark TOPSIDE of lower rail at angled intersection of the bracket.
KEYKEY
4
Mark Cut
Top post location
Bottom post location
Bottom stair rail
1/4" (0.6 cm)
2 Bottom stair
bracket bottom rail
1
1
Top stair bracket bottom rail
1/4" (0.6 cm)
4.Cut each end of the bottom stair rail, rail insert, and
bottom rail cover 1/4" (0.6 cm) shorter than the mark
on each end to allow for fit into bottom stair rail
2
brackets.
NOTE: Railing does not need to be cut at angle.
Brackets are designed to allow for railing to be
installed with standard straight cut.
2.Center lower stair bracket on post above the marked
line and attach using two self-tapping screws
100
(provided). In some cases it may be difficult to
TREX® SIGNATURETM RAILING
ATTACHING FIXED STAIR BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES/CONTINUED
TREX® SIGNATURETM
5
8
2
1
3
5.Attach "flat" bottom stair rail cover to bottom stair rail. Align cover on one side of the bottom rail in slot on side of rail. Then starting from one end of rail snap cover onto opposing slot working down the length of the rail. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
6
1
8.Position top stair rail onto balusters ensuring balusters are fully seated in top rail (position to side of post) and ENSURE that balusters are parallel with post.
9
2 1
6.Set bottom stair rail into bottom stair rail brackets. Attach bottom stair rail to bottom stair bracket using two self-tapping screws (provided) on each side of bracket.
Installing Upper Fixed Stair Brackets and Measuring Upper Rail
IMPORTANT NOTE: BEFORE CUTTING ANY TOP RAILS, MAKE SURE THAT ALL BALUSTER HOLES LINE UP PARALLEL WHEN MEASURING!
7.Place two balusters into 7
lower rail at each end closest to post.
9.Mark a light line on posts at UNDERSIDE of rail to show the location of the fixed stair brackets.
10
1
Bottom stair bracket top rail
Top stair
bracket
1
top rail
2
TREX® SIGNATURETM RAILING
10.R emove upper stair rail and center upper stair fixed bracket on post above the marked line and attach using two self-tapping screws (provided).
101 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ATTACHING FIXED STAIR BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES/CONTINUED
TREX® SIGNATURETM
Measuring Upper Stair Rail
11
13.M ark and cut top rail
13
Top stair post
cover same length as
top rail for all top rail
configurations.
Bottom
14
stair post
2
11.On top stair post location, mark UNDERSIDE of upper rail. On bottom stair post location mark TOPSIDE of upper rail at angled intersection inside the bracket.
Cutting Top Stair Rail Cover, and Attachment of Top Stair Rail Cover
KEYKEY
12
Mark Cut
Top post location
Bottom post location
Top stair rail
1/4" (0.6 cm)
1/4" (0.6 cm)
12. .C ut each end of top stair rail along with rail insert 1/4" (0.6 cm) shorter than mark to allow for fit into top stair rail bracket.
NOTE: Railing does not need to be cut at angle. Brackets are designed to allow for railing to be installed with standard straight cut.
1
3
14.A ttach "crowned" upper stair rail cover to upper stair rail by aligning cover on one side of rail. Then starting from one end of stair rail, snap cover onto opposing slot working down length of stair rail. GENTLE tapping with a rubber mallet may facilitate the fastening.
Installing Balusters into Bottom Stair Rail
15.P lace balusters into holes 15
in lower stair rail by snapping fully into place. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
TREX® SIGNATURETM RAILING
102
ATTACHING FIXED STAIR BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES/CONTINUED
TREX® SIGNATURETM
Attaching Upper Stair Rails
16. Working from one end 16
of upper stair rail, snap balusters into upper stair rail working down length of rail.
20
21
2
Trex® SignatureTM post
1
Post sleeve
3
17. A ttach top stair rail
17
to top stair bracket
(all types) using two
self-tapping screws
(provided) on each side
of stair bracket.
20. Attach post caps to Trex® SignatureTM posts (use of rubber mallet may be required for secure attachment).
21. .Attach post caps to post sleeves using external grade PVC construction adhesive.
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of stair railing to stair bracket.
Attachment of Stair Bracket Covers, Skirts, and Caps
18.A ttach corresponding
bracket covers over
18
opening in upper and
bottom rails.
1
2
19.A ttach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
19 Trex®
SignatureTM post
1
2
TREX® SIGNATURETM RAILING
103 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ATTACHING STAIR SWIVEL/COMPOUND SWIVEL BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES
TREX® SIGNATURETM
NOTES: » Illustrations shown are representations when using
Trex® SignatureTM post, but same rules apply if using pressure-treated posts and post sleeves. » U se a clamp to help hold stair brackets in place while fastening with screws. IMPORTANT NOTE: » BEFORE ATTACHING ANY UPPER BRACKETS, MAKE SURE PROPER RAILING HEIGHTS ARE ACHIEVED. RAILING HEIGHTS AND UPPER BRACKET HEIGHTS MAY NEED TO BE ADJUSTED, HOWEVER, DO NOT REDUCE HEIGHTS BASED ON YOUR RAILING CODE REQUIREMENTS. MEASURE CAREFULLY AS DIMENSION HEIGHTS MAY NEED TO BE ADJUSTED!
1
1" (2.5 cm)
1.Lay bottom stair rail on steps beside posts. Position bottom rail at least 1" (2.5 cm) above nose of stair tread.
Tip: Use a 1" (2.5 cm) deck board as a spacer board and clamp rails to post. Mark where lower brackets are to be attached to both posts. Mark at underside of railing location.
Installing Lower Stair Swivel and Compound Swivel Brackets
2
Mounting Holes
1
2
How to Measure Bottom Stair Railings (WHEN REQUIRED)
3
3.With brackets in correct swivel locations, measure distance from inside of swivel bracket to inside of swivel bracket. Ensure that before cutting, balusters holes are parallel and centered in between the posts and also allow for clearance for attachment to brackets. Mark bottom stair rail at each intersection.
Cutting Bottom Stair Rail, Bottom Stair Rail Cover, and Attachment of Bottom Stair Rail Cover
4
4.C ut each end of the bottom rail, rail insert, and bottom rail cover at the mark on each end to allow for fit into bottom stair rail brackets.
NOTE: Railing does not need to be cut at angle. Brackets are designed to allow for railing to be installed with standard straight cut.
TREX® SIGNATURETM RAILING
2.Center lower stair swivel bracket on post above
the marked line and attach using four self-tapping
screws (provided). In some cases it may be difficult
to attach the stair bracket on the lower stair post. A
90° cordless drill is recommended to attach screws
104
in this area (if possible).
ATTACHING STAIR SWIVEL/COMPOUND SWIVEL BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES/CONTINUED
TREX® SIGNATURETM
5
8
2
1
3
5.Attach "flat" bottom stair rail cover to bottom stair rail. Align cover on one side of the bottom rail in slot on side of rail. Then starting from one end of rail snap cover onto opposing slot working down the length of the rail. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
6
1
8.Position top stair rail onto balusters ensuring balusters are fully seated in top rail (position to side of post) and ENSURE that balusters are parallel with post.
Installing Upper Stair Swivel and Compound Swivel Brackets
9
2 1
6.Set bottom stair rail into bottom stair rail brackets. Attach bottom stair rail to bottom stair bracket using two self-tapping screws (provided) on each side of bracket.
Installing Upper Brackets and Measuring Upper Stair RailStair Swivel and Compound Swivel
IMPORTANT NOTE: BEFORE CUTTING ANY TOP RAILS MAKE SURE THAT WHEN MEASURING, ALL BALUSTER HOLES LINE UP PARALLEL!
9.Clamp brackets to side of rail with brackets in correct swivel location/angle (this is important to ensure correct location of swivel brackets).
10
1
7.Place two balusters into 7
lower rail at each end closest to post.
2
10.M ark a light line on posts at UNDERSIDE of where swivel bases (positioned correctly) meets the posts.
105
TREX® SIGNATURETM RAILING
ATTACHING STAIR SWIVEL/COMPOUND SWIVEL BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES/CONTINUED
TREX® SIGNATURETM
11
Mounting Holes
14
2
1
1
2
11.Remove upper stair rail from balusters and center upper stair swivel bracket on post above the marked line and attach using four self-tapping screws (provided).
12
Standard post
Standard post
3
14.A ttach "crowned" upper stair rail cover to upper stair rail by aligning cover on one side of rail. Then starting from one end of stair rail, snap cover onto opposing slot working down length of stair rail. GENTLE tapping with a rubber mallet may facilitate fastening.
Installing Balusters into Bottom Stair Rail
15
16
TREX® SIGNATURETM RAILING
12.C ut top rail along with rail insert to the measurement
between the top stair swivel brackets. For standard
post to standard post configurations this would be
same dimensions as that of the bottom stair rail.
13.M ark and cut top rail
cover same length as
13
top rail for all top rail
configurations.
15.P lace balusters into holes in lower stair rail by snapping fully into place. In some cases, GENTLE tapping with a rubber mallet may facilitate fastening.
Attaching Upper Stair Rails
16. Working from one end of upper stair rail, snap
balusters into upper
stair rail working down
17
length of rail.
17. A ttach top stair rail
to top stair bracket
(all types) using two
self-tapping screws
(provided) on each side
of stair bracket.
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of stair railing to stair bracket.
106 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ATTACHING STAIR SWIVEL/COMPOUND SWIVEL BRACKETS AND RAILS TO TREX® SIGNATURETM POSTS AND PRESSURE-TREATED POST AND POST SLEEVES/CONTINUED
TREX® SIGNATURETM
Attachment of Stair Bracket Covers, Skirts, and Caps
18
19 Trex®
SignatureTM
1
2
post
1
3 4 2
18.A ttach corresponding bracket covers over opening in upper and bottom rails.
19.A ttach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
20
21
Trex ® SignatureTM post
1
2
Post sleeve
3
20. Attach post caps to Trex® SignatureTM posts (use of rubber mallet may be required for secure attachment).
21. .A ttach post caps to post sleeves using external grade PVC construction adhesive.
ATTACHING CROSSOVER SWIVEL BRACKET ON SIGNATURE POST
TREX® SIGNATURETM
1.Follow previous instructions for installation of lower
stair rail into either fixed or swivel brackets.
2.Place two balusters into
lower stair rail at each
2
end of post.
4.Follow previous instructions marking and installation of either fixed or swivel bracket where this is required.
Attaching Stair Crossover Swivel Bracket to Post
5
Bracket cover
3
TREX® SIGNATURETM RAILING
5. Insert stair crossover swivel bracket into post.
NOTE: Keep the bracket cover on when inserting this into post, this will cover the screw attachment area.
3.Position top stair rail onto balusters ensuring balusters are fully seated in top rail (position to side of post) and ENSURE that balusters are parallel with post.
107
ATTACHING CROSSOVER SWIVEL BRACKET ON TREX® SIGNATURETM POST/CONTINUED
TREX® SIGNATURETM
6
8
X°
2
1
6. D etermine location/height of the stair crossover swivel bracket by aligning the angle of this with the fixed brackets (or compound swivel brackets) already installed (posts can be cut if necessary).
7
8. A ttach stair crossover swivel bracket to post with two self-tapping screws (provided). Slide cover over post to hide screws.
1/4" (0.6 cm)
7. O nce location/height is determined, center and predrill two holes (using a drill bit slightly smaller than that of self-tapping screw diameter) on opposite sides of post, approx. 1/4" (0.6 cm) from top of post. Drill through the post and into the stair crossover swivel bracket on each side.
NOTE: Slightly contersink pre-drilled holes to allow for flat head screw to seat flush onthe post. This will allow cover to fit over screw heads.
TREX® SIGNATURETM RAILING
108 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ATTACHING STAIR RAILS IN CROSSOVER POST APPLICATIONS
TREX® SIGNATURETM
Cutting Top Stair Rail and Insert For Stair Post-to-Stair Crossover Post Configuration
When Using Fixed Stair Brackets:
KEYKEY
9a
Mark
Cut
Standard post
Crossover post
Top stair rail
1/4" (0.6 cm)
Cutting Top Stair Rail and Rail Insert For Stair Crossover Post-to-Stair Crossover Post Configuration
KEYKEY
10
Mark
Cut
Crossover post
Crossover post
Top stair rail
9a. T op stair rail along with rail insert must be cut differently on each side of the rail. Railing side that attaches to standard post should be cut 1/4" (0.6 cm) shorter than the mark to allow for fit into top rail bracket. Railing side that attaches to the crossover post should be cut directly on the mark to allow for fit into the crossover post bracket.
When using Upper Stair Swivel and Stair Crossover Swivel Brackets:
9b
10. .C ut each end of the top stair rail along with rail insert on the mark line to allow for fit into the crossover post bracket on each side.
Cutting Top Stair Rail Cover, and Attachment of Top Stair Rail Cover
11.Mark and cut top rail
11
cover same length as
top rail for all top rail
configurations.
Crossover post
12
Standard
2
post
9b. W hen going from standard stair post to stair crossover post, measurement must be taken from inside of top horizontal stair swivel bracket to inside lip of stair crossover bracket. Crossover post will need to be modified to have swivel crossover bracket installed.
1
3
12.A ttach "crowned" upper stair rail cover to upper stair rail by aligning cover on one side of rail. Then, starting from one end of stair rail, snap cover onto opposing slot working down length of stair rail. GENTLY tapping with a rubber mallet may facilitate fastening.
109
TREX® SIGNATURETM RAILING
ATTACHING STAIR RAILS IN CROSSOVER POST APPLICATIONS/CONTINUED
TREX® SIGNATURETM
Installing Balusters into Bottom Stair Rail
13.P lace balusters into
13
holes in lower stair rail by
snapping fully into place.
In some cases, GENTLE
tapping with a rubber
mallet may facilitate
fastening.
Attachment of Stair Bracket Covers, Skirts, and Caps
16
17 Trex®
SignatureTM
post
1
1
2
Attaching Upper Stair Rails
14. W orking from one end 14
of upper stair rail, snap balusters into upper stair rail working down length of rail.
15a. For stair post-to-post configuration, attach top stair rail to top stair bracket (all types) using two self-tapping screws (provided) on each side of stair bracket.
15a
16.A ttach crossover bracket covers over opening in upper rails.
17.Attach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
18
19
Trex® SignatureTM post
2
Post sleeve
1
3
18. A ttach post caps to Trex® SignatureTM posts (use of rubber mallet may be required for secure attachment).
19. .A ttach post caps to post sleeves using external grade PVC construction adhesive.
15b. For stair crossover post configuration, fasten upper stair rail to swivel crossover post bracket by installing screws diagonally through crossover stair bracket into upper rail using two self-tapping screws (provided) on each side.
15b
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of stair railing to stair bracket.
TREX® SIGNATURETM RAILING
110 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL TREX® SIGNATURETM COCKTAIL STAIR RAILING
TREX® SIGNATURETM
Cutting Top Stair Rail, Rail Insert and Cover When using Fixed Stair Brackets
KEYKEY
5a
Mark
Cut
Standard post
Standard post
Top stair rail
IMPORTANT NOTES: » O nly for use with pressure-treated 4 x 4 post (3.5"
nominal square) and 4" x 4" (102 mm x 102 mm) post sleeve. Trex® SignatureTM posts, Trex post mounts or joist mount posts cannot be used with Trex® SignatureTM Cocktail stair railing. Cutting post and post sleeve only apply to the Cocktail style railing. » D O NOT CUT POST/POST SLEEVES UNTIL TOP RAILING AND COVER IS FULLY INSTALLED. » W hen referring to previous instructions referenced,disregard all crossover post instructions as these cannot be used with Cocktail railing. » T HE DECK BOARD USED IN TREX® SIGNATURETM COCKTAIL WILL NEED TO TERMINATE AT THE TOP OF THE POST AS SHOWN ABOVE. THE DECK BOARD WILL HAVE TO BE TOENAILED INTO THE SIDE OF THE POST IN THESE AREAS USING 2 APPROPRIATE COMPOSITE DECKING SCREWS PRE-DRILLING IS RECOMMENDED.
Installing Pressure-treated Posts, Post Sleeves,and Skirts to Use with Trex® SignatureTM Railing 1. See instructions on page 99.
Installing Brackets 2. F ollow previous stair instructions for the installation
of desired brackets, making sure that all dimensions are calculated before installation, and ensuring deck board is placed in correct location. See instructions on page 100 for fixed stair brackets and 104 for swivel stair brackets.
Cutting Bottom Stair Rail and Cover, and Attachment of Bottom Stair Rail 3. See instructions on page 100 for fixed stair brackets
and page 104 for swivel stair brackets. How to Measure Top Stair Railings (WHEN REQUIRED) 4. See instructions on page 101 for fixed stair brackets
and 105 for swivel stair brackets.
1/4" (0.6 cm)
1/4" (0.6 cm)
5aCut each end of top stair rail along with rail insert
1/4" (0.6 cm) shorter than mark to allow for fit into
top stair rail bracket.
NOTE: THE TOP RAIL WILL NEED TO BE CUT AT
APPROPRIATE ANGLE ON THE END OF THE RAIL
THAT CONNECTS TO
THE UPPER FIXED
BRACKET, SO THAT
WHEN THE RAIL IS
Post
INSTALLED IT SITS
FLUSH WITH THE END
Top stair rail
OF THE BRACKET AS
SHOWN.
Upper bracket
Cutting Top Stair Rail, Rail Insert and Cover When using Upper Stair Swivel and Compound Swivel Brackets 5b. See instructions on page 105.
Installing Balusters into Bottom Stair Rail 6. See instructions on page 102 for fixed stair brackets
and page 106 for swivel stair brackets.
Attaching Upper Stair Rails 7. See instructions on page 103 for fixed stair brackets
and page 106 for swivel stair brackets.
Lorem
TREX® SIGNATURETM RAILING
111
HOW TO INSTALL TREX® SIGNATURETM COCKTAIL STAIR RAILING
TREX® SIGNATURETM/CONTINUED
Cutting Post and Post Sleeve and Attaching Deck Board to Top Rail 8.Cut post and post
sleeves at proper angle so these are flush with the top of the top brackets and/or top rail cover. BE CAREFUL NOT to CUT brackets.
8
Top stair rail Post
11. Use scarf cut for
11
posts where two deck
boards meet.
NOTES: » Leave 1/8" (3 mm) gap
between deck boards. » Deck boards can
overhang end of last post maximum 1/2" (13 mm).
1 1
1
Upper bracket
9. P lace deck boards
9
(DO NOT use Escapes or
Contour deck boards for
top rail) over top rails.
PLACE DECK BOARD
ON TOP RAIL TO CHECK
FOR PROPER FIT AND
RAIL CLEARANCE AT
BRACKET LOCATIONS.
2
DECK BOARD MAY
REQUIRE EITHER A
NOTCH CUT ON THE UNDERSIDE OR SLIGHT
PLANING ON THE UNDERSIDE TO ALLOW DECK
BOARD TO CLEAR TOPS OF BRACKETS AND SIT
FLUSH ON TOP OF POSTS AND RAILS. Attach
boards on each post with Trex-recommended
composite screws (quantity of 2 per each board
end).
12.Where deck board
12
terminates at top of
post horizontal deck
board, PREDRILL and
toenail two approved
composite deck screws
as shown into post,
being careful to avoid
hitting stair bracket.
Attachment of Bracket Covers and Skirts 13. See instructions on page 103.
NOTE: Top Bracket Covers are not attached in this configuration.
10. Secure boards to top rail 10
using Trex® SignatureTM Cocktail Bracket (sold separately). Ensure that there is a bracket at each end of the stair railing section, then space brackets
2
approximately every 24" and attach with 4 screws provided.
NOTE: Pre-drilling before attachment is recommended.
TREX® SIGNATURETM RAILING
112 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL TREX® SIGNATURETM TRADITIONAL STAIR RAILING
TREX® SIGNATURETM
Installing Balusters into Bottom Stair Rail 8. See instructions on page 102 for fixed stair
brackets or page 106 for swivel stair brackets.
Attaching Upper Stair Rails 9. See instructions on page 103 for fixed stair brackets
or page 106 for swivel stair brackets.
Attaching 2"x 4" to Top Rail
10
IMPORTANT NOTE: » O nly for use with pressure-treated 4 x 4 post (3.5"
nominal square) and 4" x 4" (102 mm x 102 mm) or 6" x 6" post sleeve. Trex® SignatureTM Posts, Trex Post Mounts or Joist Mount Posts cannot be used with Trex® SignatureTM Traditional railing.
Installing Standard Trex® SignatureTM Stair Posts, or Pressure-treated Post 1.See instructions on page 99.
Installing Lower Stair Brackets 2. See instructions on page 100 for fixed stair brackets
or page 104 for swivel stair brackets.
How to Measure Bottom Stair Railings 3.See instructions on page 100 for fixed stair brackets
or page 105 for swivel stair brackets.
Cutting Bottom Stair Rail, Bottom Stair Rail Cover 4. See instructions on page 100 for fixed stair brackets
or page 104 for swivel stair brackets.
Attachment of Bottom Stair Rail Cover and Bottom Stair Rail 5. See instructions on page 101 for fixed stair brackets
or page 105 for swivel stair brackets.
Installing Upper Stair Brackets and Measuring Upper Rail 6.See instructions on pages 101 for fixed stair brackets
or page 105 for swivel stair brackets.
Cutting Top Stair Rail, Rail Insert and Cover 7.See instructions on page 102 for fixed stair brackets
or page 106 for swivel stair brackets.
10. Place 2" x 4" (51 mm x 102 mm) beside top rail. Mark and cut (both ends need to be cut on an angle for proper fit).
TREX® SIGNATURETM RAILING
113
HOW TO INSTALL TREX® SIGNATURETM TRADITIONAL STAIR RAILING
TREX® SIGNATURETM/CONTINUED
11. P lace 2" x 4" (51 mm x
11
102 mm) on Trex®
SignatureTM top stair rail.
13. P re-drill a pilot hole and 13
toenail 2-1/2" (6.4 cm) screw at each end of 2" x 4" (5.1 cm x 10.2 cm) into post on back side of rail (side not facing decking).
12. Secure 2" x 4" (51 mm
12
x 102 mm) to top rail
using Trex® SignatureTM
Cocktail Bracket (sold
1
separately). Ensure that
there is a bracket at each
end of the railing section,
then space brackets
2
approximately every 24"
and attach with 4 screws
provided.
NOTE: Pre-drilling before attachment is recommended.
Attachment of Lower Stair Bracket Covers, Skirts, and Caps 14a. See instructions on page 103 for fixed stair brackets or page 107 for swivel stair brackets.
NOTE: Top Bracket Covers are not attached in this configuration.
TREX® SIGNATURETM RAILING
114 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL ALUMINUM GATE
1
5
1
1
1
1
1
2
1.Measure opening between posts (gates can be customized to fit nearly any opening up to 48" [1219 mm] wide).
2.Subtract 1-7/8" (48 mm) from above measurement. This will allow for proper gapping and location of gate.
3
5.Adjust posts so that cut marks do not fall on a baluster. Make sure distance from first baluster to post is the same on both sides. Mark cut locations on panel.
NOTE: If widths do fall on a baluster, cut baluster flush at top and bottom prior to cutting panel.
6
1
3. Identify top and bottom of panel. NOTE: The posts only fit in one direction.
4
6. Cut panel using a reciprocating saw (equipped with a metal blade).
7
TREX® SIGNATURETM RAILING
4.Lay panel on a flat non-marring surface. Place posts on top of panel. Place posts so that width measurement from Step 2 is to the outside of each post.
7. Insert posts into panel.
NOTE: Make sure top and bottom of panel orientation is correct.
115
HOW TO INSTALL ALUMINUM GATE/CONTINUED
8
10
8.Secure posts to panel with four #8-18 short self-tapping screws (provided) in each location.
9.Attach shorter side of
9
hinge to the gate.
NOTE: Refer to
1
instructions included in
hardware package. Be sure
to use correct fasteners for
aluminum. See chart below.
1
2
MINIMUM FASTENER SIZE
SCREWS
Type
Length
No.
Wood Screw
2-1/2" (64 mm)
#9
Metal Screw
2" (51 mm)
#8-18
NOTE: Use of non-Trex hardware is not recommended and could result in serious injury or death.
4" max (102 mm)
10.P lace gate in opening on blocks. Sweep between
bottom of gate and top of deck cannot exceed
4" (102 mm) per IRC/IBC code regulations. Ensure
bottom gate posts will be high enough to clear skirts
on bottom of deck posts.
11.Make sure posts are plumb 11
and gate is level. Attach
1
longer side of hinges to
post using appropriate
hardware for type of post
installed. Install hinge
cover.
NOTES:
» Both wood and aluminum
2
screws are included in
hardware kit. (Refer to
chart under Step 9.)
» If using Trex Post Mounts with Post Sleeves,
pre-drilling is required using 1/8" (3 mm) drill bit,
as you must go through both aluminum sleeve and
internal post.
12.A fter determining location and height of hinge
and hasp (If using PT post/post sleeve, measure
location of latch body before attachment to post
sleeve. If necessary the L bracket of the latch body
can be removed in order to place the latch body in
proper location for latch bolt to engage.), install per
instructions included with hardware kit.
13.E nsure proper operation
of gate. Hinge tension is
14
adjustable (check hardware
1
kit instructions for more
detail).
14.A fter gate installation,
place blocks under gate
for support. Use a rubber
mallet to install cap onto
gate post. Repeat for other
gate post cap. Snap all
hinge covers into place.
2
116 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
TREX® SIGNATURETM RAILING
TREX® SIGNATURETM PANELS
NOTES: » TREX® SIGNATURETM RAILINGS ARE DESIGNED TO BE ATTACHED WITH POSTS INSTALLED AT A CLEAR SPAN OF 6' (1.83 M) OR 8' (2.44 M). » IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING POST-TO-POST CONFIGURATION, THE BOTTOM RAIL WILL
NOT NEED TO BE CUT, BUT THE TOP RAIL WILL NEED TO BE MEASURED AND CUT. » IF INSTALLING AT EXACT SPAN LENGTHS OF 6' (1.83 M) OR 8' (2.44 M), AND USING CROSSOVER POST CONFIGURATION (SPANS FROM ONE
CROSSOVER POST TO ANOTHER CROSSOVER POST), BOTH THE BOTTOM RAIL AND TOP RAIL WILL NOT NEED TO BE CUT. » IN ADDITION, AT ALL FINAL END POST CONFIGURATIONS, TOP RAIL WILL NEED TO BE MEASURED AND CUT. » S EE INFORMATION WITHIN DETAILED INSTRUCTIONS FOR MORE INFORMATION. » S EE PAGE 55 FOR SKU NUMBERS.
PARTS
A C D
K
N
H H I
J
G
G
B
E F
F
L
TOOLS NEEDED
NOTES:
» Assembled Trex® SignatureTM Panels DO NOT
come with foot blocks. You must purchase
foot blocks separately. SKU BKALFTBLK
(one per panel required on spans greater than
6', see note below***).
»Assembled Trex® SignatureTM Panels DO
M
NOT come with brackets and screws. You
must purchase the horizontal rail hardware
separately. SKU XXHZBTMBRKTPNL
(one per panel). Older horizontal rail hardware
SKU BKFHBKTAL will also work when
installing panel rails. See detailed instructions.
TREX® SIGNATURETM RAILING
A.Trex® SignatureTM upper rail cover* - 6' (actual length 73-1/2" [1867 mm]) - 8' (actual length 97-1/2" [2477 mm])
B.Trex® SignatureTM Panel (includes top and bottom railings and square balusters)
C.Crossover bracket cover (supplied with crossover post) D. Trex® SignatureTM crossover post**
- 36" (actual length 34-1/2" [876 mm]) - 42" (actual length 40-1/2" [1029 mm]) E.Trex® SignatureTM foot block*** F.Trex® SignatureTM post skirt or post sleeve skirt** G.T rex® SignatureTM post** 2-1/2" - 36" (actual length 37" [940 mm]) - 42" (actual length 43" [1092 mm]) or Trex 4x4 post sleeve** - 36" (actual length 39" [991 mm]) - 42" (actual length 45" [1143 mm]) H. Trex® SignatureTM post cap or post sleeve cap**
I. Trex® SignatureTM upper rail bracket and cover J.Trex® SignatureTM lower rail tabless bracket and
cover K.Trex decking L.Code-approved wood joist 2" x 8" (51 mm x
203 mm) or larger M. Trex Fascia N.Code-approved wood rim joist 2" x 8" (51 mm x
203 mm) or larger
*Covers are slightly longer to accommodate crossover post applications.
**Item not included in Trex® SignatureTM Panel kits. Both 4" x 4" (102 mm x 102 mm) and 6" x 6" (152 mm x 152 mm) post sleeves are designed to fit over 4" x 4" pressure-treated post.
***Required ONLY for all clear span applications over 6' (1.83 m) when fixed baluster is centered or unsupported spans greater than 5' (1.52 m). For example, if an 8' (2.44 m) panel is cut into a 5-1/2' (1.68 m) section, it would require a foot block due to the off-center placement of the fixed baluster.
NOTE: If installing 42" (1067 mm) railing, and using pressure-
treated posts with Trex post sleeves, ensure that a longer
pressure-treated post is used along with longer post sleeve,
both cut to a height of 46" (1168 mm) from decking surface.
117
BRACKET HARDWARE HORIZONTAL APPLICATIONS
(INCLUDING HORIZONTAL SWIVEL BRACKETS) TREX® SIGNATURETM
HORIZONTAL RAILING HARDWARE
AA. L ower rail bracket
BB. Lower rail bracket cover
AA
CC. Upper rail bracket cover
DD. Upper rail bracket
BB
CC
EE. F oot block base FF. Foot block support
FOOT BLOCK COMPONENTS
EE
HORIZONTAL SWIVEL HARDWARE
GG. Swivel base HH. Horizontal swivel bracket top rail II. Horizontal swivel bracket top rail cover JJ. Horizontal swivel bracket bottom rail cover KK. Horizontal swivel bracket bottom rail LL. Swivel base cover
GG HH
II
NOTE: For measurements and detailed horizontal
swivel hardware installation instructions, please
see the complete Trex® SignatureTM installation
section.
JJ
KK
DD FF LL
TREX® SIGNATURETM RAILING
118 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL PANELS
TREX® SIGNATURETM STANDARD
NOTE: FOR EASE OF INSTALLATION, IT IS RECOMMENDED THAT YOU USE THE TREX® SIGNATURETM RAIL TEMPLATES TO ATTACH BRACKETS (SOLD SEPARATELY).
Attach Brackets Using Trex® SignatureTM Posts TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. Measure 1-3/8" (3.5 cm) from top of post base plate or 1-7/8" (4.8 cm) from decking surface. Mark with light line.
1
1-3/8" (3.5 cm)
2-1/2" Post
Attach Brackets Using Pressure-Treated Posts and Post Sleeves TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. M easure 1-7/8" (4.8 cm) up from deck surface to bottom of bracket. Slide skirt up to allow for proper measurement. Mark with light line.
1
1-7/8" (4.8 cm)
2
33-7/16" (84.9 cm)
or 39-7/16" (100.2 cm)
3
1
2
2.Measure up from post base plate 33-7/16" (84.9 cm) for 36" (92 cm) rail height or 39-7/16" (100.2 cm) for 42" (107 cm) rail height. Mark with light line.
NOTE: If measuring from decking surface, measure up 33-15/16" (86.2 cm) for 36" (92 cm) rail height or 39-15/16" (101.4 cm) for 42" (107 cm) rail height.
3.Center lower bracket on post above the marked
line and attach
using two self-
4
tapping screws
(provided).
4.Center upper
1
bracket on post
above marked line
and attach using 2
(3) self-tapping
screws (provided).
NOTE: Upper bracket is not required on crossover post configuration.
2
33-15/16" (86.2 cm)
or 39-15/16" (101.4 cm)
3
1
2
2.Measure up from decking surface 33-15/16" (862 cm) for 36" (92 cm) rail height or 39-15/16" (101.4 cm) for 42" (107 cm) rail height. Mark with light line.
NOTE: Push skirt back down onto surface of decking BEFORE ATTACHING BRACKETS.
3.Center lower bracket on post above the marked
line and attach using two 2" (51 mm) wood
screws (provided).
4.C enter upper bracket 4
on post above marked
line and attach using
three 2" (51 cm) wood
1
screws (provided).
2
TREX® SIGNATURETM RAILING
119
HOW TO INSTALL PANELS/CONTINUED
TREX® SIGNATURETM
How to Measure and Cut Bottom and Top Railings of Trex® SignatureTM Panel (When REQUIRED)
1
Cutting Top Rail Option 1: For Post-to-Post Configuration
3a
KEYKEY
Mark Cut
Top rail
Standard post
Standard post
1/4" (6 mm)
1/4" (6 mm)
1.Position panel between posts and align with bottom bracket. Align center baluster with middle of span between posts (this will allow for equal spacing between end balusters and each post). Mark bottom and top rail at each end.
NOTE: If the end balusters fall too close to the brackets, the center point can be adjusted one baluster to the left or right to allow more room.
Cutting Bottom Rail
KEYKEY
2
Mark
Cut
3a.Using a saw equipped with a non-ferrous metal blade, cut each end of top rail 1/4" (6 mm) shorter than mark to allow for fit into top rail brackets.
Cutting Top Rail Option 2: For Post-to-Crossover Post Configuration
3b
KEYKEY
Mark Cut
Top rail
Crossover post
Standard post
Bottom rail
3/4" (19 mm)
1/4" (6 mm)
1/4" (6 mm)
1/4" (6 mm)
2.Using a saw equipped with a non-ferrous metal blade, cut each end of bottom rail and bottom rail insert 1/4" (6 mm) shorter than mark on each end to allow for fit into bottom rail brackets.
3b.Top rail must be cut differently on each side of the rail. Railing side that attaches to standard post should be cut 1/4" (6 mm) shorter than the mark to allow for fit into top rail bracket. Railing side that attaches to the crossover post should be cut 3/4" (19 mm) LONGER than the mark to allow for fit into the crossover post bracket.
TREX® SIGNATURETM RAILING
120 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL PANELS/CONTINUED
TREX® SIGNATURETM
Cutting Top Rail Option 3: For Crossover Post-to-Crossover Post Configuration
KEYKEY
3c
Mark Cut
Top rail Crossover post
Crossover post
If Installing Trex® SignatureTM Panel Using Lower Bracket with Tab
6a
6b
3/4" (19 mm)
3/4" (19 mm)
3c.C ut each end of top rail 3/4" (19 mm) LONGER than the mark to allow for fit into the crossover post bracket on each side.
4 Top rail
6a. B reak or cut the bottom tab off the bottom brackets.
6b. P ut a dab of silicone in the basket of the bottom bracket to prevent rattle.
If Installing Trex® SignatureTM Panel Using Lower Rail Tabless Bracket 7. P eel backings from
adhesive strip provided 7a
and place inside the bottom bracket.
3/4" (19 mm)
3/4" (19 mm)
8
4.Using razor knife or other cutting tool, cut rail insert 3/4" (19 mm) FROM EACH SIDE.
5.Mark and cut top rail
5
cover same length as
top rail for all top rail
configurations
8.Place panel in bottom and top brackets.
TREX® SIGNATURETM RAILING
121
HOW TO INSTALL PANELS/CONTINUED
TREX® SIGNATURETM
9.For post-to-post
9
configuration, fasten
upper rail to each
bracket by installing
2
screws diagonally
through upper rail into
bracket using two self-
tapping screws each side (provided with
7/64" 1 (2.8 mm)
bracket kit).
10.F or crossover post
10
configuration, fasten
upper rail to crossover
post by installing screws
2
diagonally through
upper rail into post using
two self-tapping screws
each side (provided with 7/64" 1
bracket kit).
(2.8 mm)
NOTE: Pre-drilling is recommended (7/64" [2.8 mm] drill bit) for attachment of railing to bracket.
11 2 1
13.A ttach provided post
13
skirt to bottom of
posts when using Trex®
SignatureTM posts.
2
Trex ® SignatureTM post
1
14
15
1
Trex ® SignatureTM post
2 Post sleeve
1
3
14. A ttach post caps to Trex® SignatureTM posts (use of rubber mallet may be required for secure attachment).
15.A ttach post caps to post sleeves using external grade PVC construction adhesive.
16.F or crossover post
configuration, attach
16
crossover post cap to
crossover post.
3
11.Attach upper rail cover to upper rail by aligning cover on one side of rail. Then, starting from one end of rail, snap cover onto opposing slot working down length of rail. GENTLE tapping with a rubber mallet may facilitate fastening.
Attachment of Bracket Covers, Skirts, and Caps
12.A ttach corresponding
bracket covers over
12
opening in upper and
1
bottom rails.
2
TREX® SIGNATURETM RAILING
122 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL FOOT BLOCKS PANELS
TREX® SIGNATURETM
Attachment of Foot Block (Required ONLY for All Clear Span Applications Over 6' [1.83 m])
NOTE: Pre-drilling is recommended (1/8" [33 mm] drill bit) for attachment of base.
3.After attached, use a
3
1
rubber mallet along
1
with scrap piece of
wood to tap foot block
until it locks into place.
1
2
1.To ensure correct location, place foot block under
center of bottom rail. Mark to provide placement
location of base.
2.Place base (smaller
2
side facing down) on
decking surface. Attach
base of foot block
using one screw at an
angle through base and
into decking.
TREX® SIGNATURETM RAILING
123
HOW TO INSTALL HORIZONTAL ROD RAILING
TREX® SIGNATURETM STANDARD
NOTES: » Adjust drill power to lowest setting that will drive screw. DO NOT OVER TORQUE 316 STAINLESS STEEL
STAINLESS FASTENERS. » NEVER use impact tools on 316 Stainless Steel Fasteners. » Be careful inserting rods through intermediate vertical supports. Lay pieces on a flat, solid surface and insert as
straight as possible to prevent scratching. » When marking lines on bottom rail, do not make a mark wider than 1" or it will be visible after installation. » TOP AND BOTTOM RAILS ARE DIFFERENT LENGTHS, TO ACCOMMODATE THE INSTALLATION OF CROSSOVER
POST APPLICATIONS.
PARTS
IC
I
TOOLS NEEDED
A E
F
H
B
G
L K J
P
O
N D
M
N
#2 Square Bit
M
1/4" (6.4 mm)
Q
7/64" (2.8 mm) or similar sized metal punch
Non-ferrous metal cutting blade
A. Trex® SignatureTM top rail and crowned cover - 6' (actual length 73-1/2" [1867 mm]) - 8' (actual length 97-1/2" [2477 mm])
B. Trex® SignatureTM bottom rail and flat cover - 6' Rail (actual length 71-1/2" [181.6 cm]) - 6' Cover (actual length 70" [177.8 cm]) - 8' Rail (actual length 95-1/2" [242.6 cm]) - 8' Cover (actual length 94" [238.8 cm])
C. Trex® SignatureTM upper rail bracket and cover D. Trex® SignatureTM lower rail bracket and cover E. Anti-rattle strip F. Rod G. End vertical support H. Intermediate vertical support* I. Trex® SignatureTM post cap or post sleeve cap** J. Template K. Trex decking L. HZ spacer
M. Trex® SignatureTM post skirt or post sleeve skirt** N. Trex® SignatureTM post*
(2" or 2.5" depending on application) - 36" (actual length 37" [94.0 cm]) - 42" (actual length 43" [109.2 cm]) or Trex 4" x 4" post sleeve* - 36" (actual length 39" [99.1 cm]) - 42" (actual length 45" [114.3 cm]) O. Code-approved wood rim joist 2" x 8" (5.1 cm x 20.3 cm) or larger P. Code-approved wood joist 2" x 8" (5.1 cm x 20.3 cm) or larger Q. Trex Fascia * 1 for 6' span/2 for 8' span **Item not included in Trex® SignatureTM Railing kits. Both 4" x 4" (10.2 cm x 10.2 cm) and 6" x 6" (15.2 cm x 15.2 cm) post sleeves are designed to fit over 4" x 4" pressure-treated post. *** For 8' Rail Sections only - RODRAILSTIFFENER (included with kit), not shown above
TREX® SIGNATURETM RAILING
124 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL ROD RAILING BRACKETS
TREX® SIGNATURETM STANDARD
Attach Brackets Using Trex® SignatureTM Posts TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. Measure 1-3/8"
1
(3.5 cm) from top of
post base plate or
1-7/8" (4.8 cm) from
decking surface. Mark
with light line.
1-3/8" (3.5 cm)
2-1/2" Post
2
33-7/16" (84.9 cm)
or 39-7/16" (100.2 cm)
3
1
2
2.Measure up from post base plate 33-7/16" (84.9 cm) for 36" (92 cm) rail height or 39-7/16" (100.2 cm) for 42" (107 cm) rail height. Mark with light line.
NOTE: If measuring from decking surface, measure up 33-15/16" (86.2 cm) for 36" (92 cm) rail height or 39-15/16" (101.4 cm) for 42" (107 cm) rail height.
3.Center lower bracket on post above the marked
line and attach using two self-tapping screws
(provided).
4.Center upper
4
bracket on post
above marked line
1
and attach using
(3) self-tapping
2
screws (provided).
NOTE: Upper bracket is not required on crossover post configuration.
Attach Brackets Using Pressure-Treated Posts and Post Sleeves TIP: Use a clamp to help hold brackets in place while fastening with screws.
1. M easure 1-7/8"
1
(4.8 cm) up from deck
surface to bottom of
bracket. Slide skirt up
to allow for proper
measurement. Mark
with light line.
1-7/8" (4.8 cm)
2
33-15/16" (86.2 cm)
or 39-15/16" (101.4 cm)
3
1
2
2.Measure up from decking surface 33-15/16" (862 cm) for 36" (92 cm) rail height or 39-15/16" (101.4 cm) for 42" (107 cm) rail height. Mark with light line.
NOTE: Push skirt back down onto surface of decking BEFORE ATTACHING BRACKETS.
3.Center lower bracket on post above the marked
line and attach using two 2" (51 mm) wood
screws (provided).
4.C enter upper bracket 4
on post above
marked line and
1
attach using three 2"
(51 cm) wood screws
2
(provided).
TREX® SIGNATURETM RAILING
HOW TO INSTALL HORIZONTAL ROD RAILING/
TREX® SIGNATURETM STANDARD
1.Prepare a solid work surface area (plywood, deck surface, etc.).
How to Measure Bottom and Top Railings (When Required) 2.For Full Span Post to Post Applications only top
rail will need to be cut.
3.For Full Span Crossover to Crossover post Applications no rails have to be cut, HOWEVER the location of the HZ Template on the top rail will need to be adjusted in 3/4" on each side of top rail to allow for proper placement of vertical supports.
125
HOW TO INSTALL HORIZONTAL ROD RAILING/CONTINUED
TREX® SIGNATURETM STANDARD
4
Locating Vertical Holes on Bottom and Top Rails
8
Bottom rail
Top rail
4.Position bottom and top rails between posts .and align with bottom bracket. Mark bottom rail and top rail at each end.
Cutting Railings and Covers
KEYKEY
5
Mark
Cut
1/4" (0.6 cm)
Bottom rail
1/4" (0.6 cm)
5.Cut each end of bottom and top rail 1/4" (0.6 cm) shorter than mark on each end to allow for fit into bottom rail brackets.
If installing crossover railing, add 3/4" to each side of top rail.
If using swivel brackets, measure distance between brackets and cut railings to this distance.
6
7
Bottom rail
2
1
8. Place HZ template at end of top and bottom rails. Pre-drill pilot holes (using a 7/64" bit or small punch) at locations.
NOTES: » Template is labeled for the type of bracket used. » Pilot holes will be drilled out larger in a later step. » For Compound Swivel Brackets, set the rail in the
bracket and mark 3.75" from the post. 6' Rail Spans or Shorter
9a
9a. Measure the distance between the vertical end holes on both top and bottom rails. Mark the center.
IMPORTANT: DO NOT mark the line across the entire width of the bottom rail, as it will be visible after install. Maximum recommended line width is 1".
Bottom rail cover
1-1/2" (3.8 cm)
6. Mark and cut bottom rail cover 1-1/2" (3.8 cm) shorter than bottom rail.
7.Mark and cut top rail cover same length as top rail for all top rail configurations.
TREX® SIGNATURETM RAILING
126 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL ROD RAILING/CONTINUED
TREX® SIGNATURETM STANDARD
Over 6' Rail Spans
Cutting Rods to Length (When Required)
9b
12
X" + 3/8" X" + 3/8"
9b.M easure the distance between the vertical end holes on both top and bottom rails. Divide the distance into thirds and make two marks on top and bottom rails.
12.Measure the distance between the end (outer) holes (X") on top or bottom rail and add 3/8" to this measurement.
NOTE: Maximum unsupported rod span is 32.25". Locating and Drilling Midspan Holes
10
NOTE: If installed at exact spans, rods do not have to be cut.
13
X" + 3/8"
TREX® SIGNATURETM RAILING
1
2
10.U sing the slot on the HZ template, locate marked line and drill two 7/64" pilot holes (or mark with a punch).
NOTE: Pilot holes will be drilled out larger in next step.
11.Using pilot holes
11
(or marks), drill 1/4"
holes for all vertical
supports in both top
and bottom rails.
NOTE: Clean any burrs from edges of holes to ensure good fit on both sides.
13.Cut rods to the length measured in previous step.
Vertical and Rod Assembly
14.Insert anti-rattle
14
strips into the
vertical supports.
NOTE: There are two anti-rattle strips for each support which can only be inserted in one side.
15
1 1
2
15.Attach one end vertical and all intermediate verticals to bottom rail using HZ spacer and screws provided. 127
HOW TO INSTALL HORIZONTAL ROD RAILING/CONTINUED
TREX® SIGNATURETM STANDARD
16
20
16.Slide all rods through intermediate supports and into end vertical support.
NOTE: When inserting rods through intermediate supports, keep rods straight to avoid scratching.
17
1
1
1
20. Drop assembled rod rail panel into brackets.
21
22
2 2
2
17.Slide end vertical onto rods and attach to bottom rail using HZ spacer and screws provided.
Installing Top and Bottom Rails
18
18. Using a mallet, install bottom rail cover onto bottom rail.
19
1
1 1
1 7/64" (.28 cm)
7/64" 1 (.28 cm)
21.Attach bottom rail to to bottom brackets by using one self-tapping screw (provided) for each bracket.
22.Attach top rail to top brackets by using two selftapping screws (provided) for each bracket.
NOTE: Pre-drilling is required (7/64" [0.28 cm] drill bit) for attachment of railing to bracket.
Inserting Rod Rail Stiffener For Rail Sections over 6'
23
Rod sti ener
2
23. Attach tape (qty 6 provided) to alternating sides of the rod stiffener as shown.
19.Install top rail to all vertical and end supports using HZ spacer and screws provided.
128 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
TREX® SIGNATURETM RAILING
HOW TO INSTALL HORIZONTAL ROD RAILING/CONTINUED
TREX® SIGNATURETM STANDARD
24
Rod sti ener
Attachment of Bracket Covers, Skirts, and Caps
26
1
27 Signature post
1
24. Place rod stiffener inside rail channel.
2 2
26A ttach corresponding bracket covers over opening
25
in top and bottom rails.
27.Attach provided post skirt to bottom of posts when
using Trex® SignatureTM posts.
28
29
1
Signature post
2 Post sleeve
25. Using a mallet, install top rail cover.
1
3
28. A ttach post caps to Trex® SignatureTM posts. (Use of rubber mallet may be required for secure attachment.)
29.A ttach post caps to post sleeves using external grade PVC construction adhesive.
TREX® SIGNATURETM RAILING
129
HOW TO INSTALL TREX® SIGNATURETM STAIR POSTS AND HORIZONTAL ROD RAILING STAIRS
TREX® SIGNATURETM STANDARD
TOOLS NEEDED
8 #2#S2quSaqrueare
Ir8wIirnwQinuQicukicCklaCmlapms ps (or(osirmsilmari)lar)
BitBit
5/156/"16"
(7.9(7m.9mm)m)
dridllrbililtbit
forfostrasirtsairs 7/674/6" 4"
(2.(82m.8mm)m)
NoNn-ofne-rfreorursous
or osirmsilmarilsairzseidzed
memtaeltcaul tctuintgtinbglabdleade
memtaeltpaul npcuhnch
INSTALLING STANDARD STAIR POSTS, OR PRESSURE-TREATED POST, POST SLEEVES AND SKIRTS TREX® SIGNATURETM STANDARD
1.Make sure 53" (135.6 cm) posts are used for all stair posts.
2
2.If Trex® SignatureTM stair posts are used, install at nose of stair tread directly under required blocking. Refer to Trex® SignatureTM Instructions for detailed post installation.
3.If pressure-treated post/ 3
post sleeves are used, posts are to be installed to the inside of the last stair stringer. (Rails must be over decking surface.) Refer to Trex® SignatureTM Instructions for detailed post installation.
BRACKET HARDWARE STAIR APPLICATIONS
TREX® SIGNATURETM STANDARD
AA
DD
AA. B ottom Stair Bracket and Cover Lower Rail
BB. T op Stair Bracket and Cover Lower Rail
CC. Fastener Pack
DD. B ottom Stair Bracket and Cover Upper Rail
EE
EE. Top Stair Bracket and Cover Upper Rail
BB
HOW TO INSTALL HORIZONTAL ROD RAILING STAIRS
TREX® SIGNATURETM STANDARD
1
NOTES:
» A ll Trex® SignatureTM fixed stair brackets ONLY work
with stair slopes of 32°-37°. » Illustrations shown are representations when using
1" (2.5 cm)
Trex® SignatureTM post, but same rules apply if using
pressure-treated posts and post sleeves.
TREX® SIGNATURETM RAILING
1.Place a 1" deckboard on the nose of the stair
tread, then lay the bottom stair rail on top of the
deckboard. Use the lower and upper stair post to
set the size of the lower stair rail. On UPPER STAIR
POST, mark from underside of bottom rail. ON
LOWER STAIR POST, mark from top side of
130
bottom rail.
HOW TO INSTALL HORIZONTAL ROD RAILING STAIRS/CONTINUED
TREX® SIGNATURETM STANDARD
KEYKEY
2
Mark
Cut
Installing Upper Stair Brackets 5
Bottom stair rail
1/4" (0.6 cm)
36" 33-1/4" 42" 39-1/4"
Upper post
36" 33-1/8" 42" 39-1/8"
1/4" (0.6 cm)
2.C ut each end of the bottom stair rail and bottom rail cover 1/4" (0.6 cm) shorter than the mark on each end to allow for fit into bottom stair rail brackets.
NOTE: Railing does not need to be cut at angle. Brackets are designed to allow for railing to be installed with standard straight cut.
3
1" (2.5 cm)
Lower post
5.On Lower Post From top of lower bracket, measure up and mark with light line (33-1/4" for 36" rail; 39-1/4" for 42" rail). O n Upper Post From top of lower (upper) bracket, measure up and mark with light line (33-1/8" for 36"rail; 39-1/8" for 42" rail).
6
1
Lower stair bracket
top rail
Upper stair
bracket
1
top rail
2
3.With deckboard still on nose of stair tread, place
6.C enter upper stair brackets on posts below
brackets on end of bottom stair rail (DO NOT
the .marked lines and attach using two self-tapping
attach brackets to rail) and mark posts for bracket
screws (provided).
locations.
Installing Lower Stair Brackets
7.Set bottom stair rail
7
into bottom stair rail
brackets.
4
Bottom stair
bracket bottom rail
1
2
1
Top stair
bracket
bottom rail
2
4.Center lower stair bracket on post above the marked line and attach using two self-tapping screws (provided). In some cases it may be difficult to attach the stair bracket on the lower stair post. Recommend using a 90° drill adapter or loosen the post to get access to the lower bracket screw holes.
TREX® SIGNATURETM RAILING
131 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL ROD RAILING STAIRS/CONTINUED
TREX® SIGNATURETM STANDARD
How to Mark, Cut and Place Top Stair Railing 8
Measuring and Cutting Rods 11
8.Position top rail to side of post. Mark top stair rail at each location stated. On UPPER STAIR POST, mark from underside of bottom rail. On LOWER STAIR POST, mark from topside of bottom rail.
KEYKEY
9
Mark
Cut
1/4" (0.6 cm)
Top stair rail
1/4" (0.6 cm)
X" + 3/8"
11. Using the long edge of the stair template, mark the location of the end verticals on the upper and lower rails.
NOTE: Mark should only be 1" max length or it will be visible after installation of vertical.
12
X" + 3/8"
9. Cut each end of top stair rail and top rail cover 1/4" (0.6 cm) shorter than mark to allow for fit into top stair rail bracket.
NOTE: Railing does not need to be cut at angle. Brackets are designed to allow for railing to be installed with standard straight cut.
10. Set top stair rail into 10
top stair rail brackets.
12.M easure and mark the mid-line (6' sections) of the two end marks of the top and bottom rail. Take that measurement and add 3/8" for rod length in next step.
NOTE: For 8' sections divide the distance into thirds and make two marks for the two verticals.
13
X" + 3/8"
13.Cut rods to the length measured in previous step.
IMPORTANT: DO NOT CUT RODS AT RAIL ANGLE; MAKE 90° CUTS ONLY!
132 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
TREX® SIGNATURETM RAILING
HOW TO INSTALL HORIZONTAL ROD RAILING STAIRS/CONTINUED
TREX® SIGNATURETM STANDARD 17
Measuring and Cutting Verticals
14
14.C lamp first vertical (lower part of stairs) in place, using width of stair template to position.
15
17. Clamp top vertical (upper part of stairs) in place, using width of stair template to position.
18
15. Clamp middle vertical(s) in place.
16
18. .Mark angle cuts at top and bottom on all verticals
19.A fter removing rods
19
and verticals, make
angle cuts on top and
bottom of verticals
following marks from
previous step.
TREX® SIGNATURETM RAILING
16.S lide a rod into top and bottom of all verticals. Ensure that distance of top rod to top rail and bottom rod to bottom rail are equal.
Vertical and Rod Assembly
20. Insert anti-rattle
20
strips into the vertical
supports.
NOTE: There are two anti-rattle strips for each support which can only be inserted in one side.
133
HOW TO INSTALL HORIZONTAL ROD RAILING STAIRS/CONTINUED
TREX® SIGNATURETM STANDARD
21
25
2
1 1
1
1
2
21.Using the slot on the HZ template, locate marked line and drill two 7/64" pilot holes at each mark (or mark with a punch).
NOTE: Pilot holes will be drilled out larger in next step.
22.Using pilot holes
22
(or marks), drill 5/16"
holes for all vertical
supports in both top
and bottom rails.
25.Slide upper end vertical onto rods and attach to bottom rail using ST Wedge Spacer and screws provided.
26
Installing Top and Bottom Rails 23
1
1
2
26. Using a mallet, install bottom rail cover onto bottom rail.
27
1 1 1
23.Ins1tall lowest end vertical and all intermediate verticals to bottom rail using ST Wedge Spacer and screws provided.
24
2
27.Install top rail to all vertical and end supports using ST Wedge Spacer and screws provided.
TREX® SIGNATURETM RAILING
24.Slide rods into lower end and all intermediate
1
verticals.
NOTE: When Inserting rods Into intermediate supports, keep rods straight to avoid scratching. 134
NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL HORIZONTAL ROD RAILING STAIRS/CONTINUED
TREX® SIGNATURETM STANDARD
Final Installation
Attachment of Bracket Covers, Skirts, and Caps
28
32
33 Signature
Post
1
1
28. Drop assembled stair rod rail panel into brackets.
29
30
2
2
2
32.A ttach corresponding bracket covers over opening in upper and bottom rails.
33.A ttach provided post skirt to bottom of posts when using Trex® SignatureTM posts.
34
35
2 Signature Post
1
2
Post sleeve
3
29.A ttach bottom stair rail to bottom stair bracket using two self-tapping screws (provided) on each side of bracket.
30.A ttach top stair rail to top stair bracket (all types) using two self-tapping screws (provided) on each side of stair bracket.
31
34. A ttach post caps to Trex® SignatureTM posts. (Use of rubber mallet may be required for secure attachment.)
35.A ttach post caps to post sleeves using external grade PVC construction adhesive.
TREX® SIGNATURETM RAILING
31. Using a mallet, install top rail cover. 135
TREX SELECT RAILING
NOTES: » All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (176.8 cm) for
6' (1.83 m) on center, and 92-5/8" (235.3 cm) for 8' (2.44 m) on center. Note that railings are designed to be slightly longer that required to allow for very slight play in post placement trimming may be required. IT IS VERY IMPORTANT TO MEASURE FIRST. » S EE PAGE 57 FOR SKU NUMBERS.
F*
PARTS
A
D
O
B
E
C H**
C I
G*
K
L
J
A. Select top rail B. Select bottom rail C. Brackets D. Balusters E. Adjustable foot block F. Post sleeve cap* G. Post sleeve skirt* H. P ost sleeve 4" x 4" (102 mm x 102 mm) or
6" x 6" (152 mm x 152 mm) post sleeve)** I. Trex decking J. Trex fascia K. C ode-approved wood joist 2" x 8"
(51 mm x 203 mm) L. Code-approved wood rim joist 2" x 8"
(51 mm x 203 mm) or larger
* Item not included in the Select railing kits. ** B oth 4" x 4" (102 mm x 102 mm) and 6" x 6" (152 mm x 152 mm)
post sleeves are designed to fit over 4x4 pressure-treated post.
NOTE: If installing 42" (1067 mm) railing, use longer posts sleeves and measure accordingly to ensure a proper cut (DO NOT CUT POST SLEEVES TO ACTUAL 42" THESE NEED TO BE LONGER TO ALLOW FOR POST CAPS TO FIT).
NOTE: Pictorial representations shown may only show one style of railing, while others may also be used. Review detailed instructions to determine what railing styles and combinations can be used.
DETERMINING BALUSTERS NEEDED
Baluster Type
Round Aluminum Baluster (Horizontal Application)
Round Aluminum Baluster(Stair Application)
Per 6' OC Section
14
12
Per 8' OC Section
20
16
CODE APPROVED APPLICATIONS
6' Railing
8' Railing
< 30" height decking
IRC Compliant IBC Compliant
Acceptable (Code approval not applicable)
Yes
No
Acceptable (Code approval not applicable)
No
No
NOTE: If using 8' railings, the Trex Select® 8' Aluminum Rail Stiffener (sku SELALRAILSTIFFENER) can also be used to allow for the rail to be stronger if required.
136 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
SELECT RAILING
TREX SELECT RAILING
RAILING CONFIGURATIONS
Standard
B A
D C
Cutting post sleeves is NOT required. A. Pressure-treated post or Trex post mounts* with Trex Transcend post sleeves, or Trex
joist mount posts* B. Select top rail C. Select bottom rail D. Select balusters See page 137 for "How to Install Standard Railing".
Cocktail
B
C
A
E
D
Post sleeves WILL NEED TO BE CUT. A. Pressure-treated post with Trex Transcend post sleeve
NOTE: » O nly for use with 4" x 4" (102 mm x 102 mm) post sleeve. » T rex post mounts or joist mount posts cannot be Select cocktail design.
B. Deck board top rail. NOTES: » Contour and Escapes cannot be used » Deck boards will need to be cut to fit each rail span
C. Select top rail D. Select bottom rail E. Select balusters See page 140 for "How to Install Select Cocktail Railing".
POST SLEEVES
WILL NEED TO BE CUT
Traditional
B
C
A
E
D
Cutting post sleeves is NOT required. A. P ressure-treated post or Trex post mounts* with Trex Transcend post sleeves, or Trex
joist mount posts* B. 2" x 4" (51 mm x 102 mm) lateral top rail C. Select top rail D. Select bottom rail E. Select balusters See page 141 for "How to Install Traditional Railing".
*See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing.
HOW TO INSTALL TREX SELECT STANDARD RAILING
TREX SELECT
Read all instructions BEFORE installation.
Important: Post sleeves are NOT to be cut for this design style.
SELECT RAILING
137
HOW TO INSTALL TREX SELECT RAILING/CONTINUED
TREX SELECT
Installing Pressure-Treated Posts
»Select Railing Kits are
designed for posts to
1
be installed at maximum
of 6' or 8' (1.83 m or 2.44 m) ON CENTER depending on the length being used. NOTE: Smaller spans are
2" x 8" (51 mm x 203 mm)
min.
1" (25 mm) min.
5-1/8" (130 mm) min.
allowed.
»Attach posts using
1/2" (13 mm) carriage
bolts.
» Minimum joist size is 2" x 8" (51 mm x 203 mm).
» Top bolts must be 1" (25 mm) from tops of joists.
» Bottom bolts must be 5-1/8" (130 mm) from top bolts.
NOTE: Blocking MUST be added for extra strength.
Installing Post Sleeve
2
Skirts and Post Sleeves
2. Slide post sleeve skirt
over post and down to
2
rest on decking surface.
1
Slide post sleeve over
post and position inside
post sleeve skirt.
NOTE: Shims can be used to plumb post sleeves.
IMPORTANT NOTE REGARDING FOOT BLOCK INSTALLATION: » Refer to detailed instructions (Trex
Select®) rail instructions) included with foot block prior to installation of railing section as these include other required steps for proper installation.
Attaching Foot Block to
4
Bottom Rail
4. Invert the bottom rail.
Center and drill a hole
using a 3/16" (5 mm)
1
drill bit. This will be
location for foot block
attachment(to be
installed last).
2
Attaching Brackets to Rails
5a
Top Rail
5b Bottom Rail
2
Cutting Railings
3a
3b 1-9/16" (40 mm)
5a. P osition brackets on each end of TOP RAIL on the same side as baluster holes. Attach brackets using three #8-18 x 1" self-drilling screws (provided).
5b. P osition brackets on each end of BOTTOM RAIL on the OPPOSITE SIDE of the baluster holes. Attach brackets using three #8-18 x 1" self-drilling screws (provided).
Assembling Railing Section
6a
6b
SELECT RAILING
3a. Position bottom and top rails between posts, ensuring baluster holes are lined up and spaced evenly.
3b. A lso allow for a minimum of 1-9/16" (40 mm) on each end of rail for bracket placement AND baluster clearance. Mark rails at intersection of rail and post.
6a. O n a clean flat surface, lay bottom railing on its side. Make sure to allow enough room for installation of balusters and top rail. Place a scrap piece of 1" (25 mm) decking board running parallel to bottom rail for support when installing balusters.
6b. Insert balusters into bottom rail slots until balusters are fully seated.
138 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL TREX SELECT RAILING/CONTINUED
TREX SELECT
6c
6d
7c
6c. A ttach top rail to balusters, feeding each baluster into required slots. Start on one end and work towards the other.
6d. To help temporarily secure the railing section together, place a ratchet strap around the top and bottom rail and tighten until snug. DO NOT OVERTIGHTEN AS YOU CAN BEND THE RAILING.
Installing Railing Section to Posts
7a
7b
3-3/4" (95 mm)
7c. Install both bottom and top brackets on each side to post using two #8-10 x 2" wood screws (provided). For best results, set drill to low speed when installing these screws.
Attaching Post Caps and
8
Installing Foot Block
8.Secure post caps
with silicone or PVC
adhesive. Attach new
foot block per foot block
instructions.
2 1
NOTE: Clean up any excess adhesive before it dries.
7a. Using scrap material (i.e. 2 x 4s, decking boards, etc.) cut at least three support blocks at 3-3/4" (95 mm) in height. Place one each on decking surface beside each post and one near center of span.
7b. L ift secured railing section up, and CENTER this section in between the spanned posts on prepositioned support blocks.
NOTE: To help stabilize railing section use a quickgrip clamp (or other type of clamp) and clamp the first baluster to post sleeve. (DO NOT OVERTIGHTEN CLAMP.)
SELECT RAILING
139
HOW TO INSTALL COCKTAIL RAILING
TREX SELECT
Important: ONLY use for use with pressure-treated 4x4 post (3.5" nominal square) and 4" x 4" (102 mm x 102 mm) post sleeve. Trex Post Mounts or Joist Mount Posts cannot be used with Select Cocktail railing.
Cutting Deck Board
6
1. Installing Pressure-Treated Posts, Post Sleeve Skirts and Post Sleeves See instructions on page 138.
Cutting Post and Post Sleeve
1a.Mark and cut post and
post sleeve measuring
1a
from deck surface:
» 36-1/8" (918 mm) for
36" (914 mm) height.
» 42-1/8" (1070 mm) for 42" (1067 mm) height.
4. C utting Railings
36-1/8" (918 mm)
or 42-1/8" (1070 mm)
See instructions on page
138.
5. Attaching Foot Block to Bottom Railing See instructions on page 138.
NOTES: » Leave 1/8" (3 mm) gap between deck boards. » D eck boards can overhang end of last post
maximum 1/2" (13 mm).
6. Cut deck boards to appropriate length of railing span, remembering to include extra space on each side of the deck board to allow for attachment to the post. Decking boards must cover 1/2 of the pressure-treated post to allow this to be fastened later.
7.Place inverted deck board (place top side
7
of deck board down)
on clean, flat surface.
(DO NOT use Escapes
or Contour deck
boards for top rail.)
Attaching Deck Board to Select Top Rail 8. Place inverted Select
top rail (orient properly 8
so baluster holes are shown top side up), on the deck board, centered in both directions to allow final attachment to post.
SELECT RAILING
140 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL COCKTAIL RAILING/CONTINUED
TREX SELECT
9. Secure deck board
9
to Select top rail with
3/4" screws provided
approx. every 16" on
center. Screws are to be
installed inside of the
baluster holes into the
decking board. DO NOT
overtighten.
NOTES: » A long drill bit will be required to fit inside the
baluster holes. » If installing 8' rail section and using Aluminum Rail
Stiffener, predrilling will be required through the
stiffener.
11. Installing Railing Sections to Posts See instructions on page 139.
12.A ttaching Deck Board 12
to Posts Attach boards on
each post with Trex recommended composite screws (quantity of 2 per each board end).
13. Installing Foot Block Install foot block per detailed instructions.
10.A ssembling Railing Sections See instructions on page 138.
HOW TO INSTALL TREX TRADITIONAL RAILING
TREX SELECT Cutting 2" x 4"
4
SELECT RAILING
1. Installing Pressure-Treated Posts, Post Sleeve Skirts and Post Sleeves See instructions on page 138.
2. Attaching Foot Block to Bottom Railing See instructions on page 138.
3. C utting Railings See instructions on page 138.
4.C ut 2" x 4" (51 mm x 102 mm) to same length of the inverted Select top rail.
Attaching 2" x 4" to Select Top Rail
5
6
5.Place inverted 2" x 4" (51 mm x 102 mm) (place topside down) on clean, flat surface.
6.Place inverted Select top (orient properly so baluster holes are shown top side up) on 2" x 4" (51 mm x 102 mm).
141
HOW TO INSTALL TREX TRADITIONAL RAILING/CONTINUED
TREX SELECT
7
7.Secure 2" x 4" (51 mm x 102 mm) to Select top rail with 3/4" screw provided approx. every 16" on center. Screws are to be installed inside of the baluster holes into the decking board.
NOTES: » DO NOT overtighten. Note that a long drill bit will
be required to fit inside the baluster holes. » If installing 8' rail section and using Aluminum Rail
Stiffener, predrilling will be required through the stiffener.
9. Installing Railing
10
Sections to Posts
See instructions on page
1
138.
10.A ttaching 2x4 to Posts
Pre-drill a pilot hole
and toenail 2-1/2"
(64 mm) screw at each
end of 2" x 4" (51 mm
x 102 mm) into post on back side of rail (side not
facing decking).
11.Attaching Post Caps and Installing Foot Block See instructions on page 139.
8. Assembling Railing Sections See instructions on page 138.
HOW TO INSTALL ON-AN-ANGLE RAILING
TREX SELECT
NOTE: Brackets are designed to be installed up to a 45° angle.
4 x 4 OR 6 x 6 Post Sleeve
4 x 4 Post Sleeve
6 x 6 Post Sleeve
Both 4" x 4" (102 mm x 102 mm) or 6" x 6" (152 mm x 152 mm) post sleeves work well for angles up to 45 degrees. Bottom rail brackets may need to be slightly offset to one side in order to fit properly to hold rail in place. Before attaching bracket to rail, measure and mark to ensure bottom rail remains parallel to upper rail.
SELECT RAILING
142 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL TREX SELECT STAIR RAILING
TREX SELECT
Read all instructions BEFORE installation. IMPORTANT NOTE: POST TO POST SPAN WILL BE LESS THAN 6'. PRIOR TO INSTALLING POSTS, CALCULATE POST TO POST SPAN USING A MAXIMUM RAIL LENGTH OF 6' AND THE ANGLE (32°-37°) AT WHICH THE RAILS WILL BE INSTALLED. DO NOT INSTALL STAIR POSTS AT 6' SPAN, AS STAIR RAILINGS WILL THEN BE TOO SHORT.
NOTE: All Select railings work ONLY WITH STAIR SLOPES OF 32° TO 37°.
Installing Posts, Post
1
Sleeve Skirts, and Post
Sleeves for Stair Rails
1.Install posts, post
sleeve skirts, and post
sleeves according to
standard Select railing
instructions.
Cutting Balusters on
3a
Angle (OPTIONAL)
3a. In order for balusters
to seat properly
(depending on the
angle of the stair
railing), the balusters
may need to be
trimmed to match the
angle of the bottom and top railing.
3b
» In most cases, a post and post sleeve longer than 39" (991 mm) will be needed on the lower section of stair rail to accommodate stair angle.
» Make sure top and bottom posts for stars are installed at nose of each tread.
Measuring and Cutting Railings
3b. S et bottom railing on nose of stair treads and set baluster at 90° on the outside of the railing. Mark and measure the angle.
NOTE: Measure, mark, and cut a scrap board to ensure you have proper angle BEFORE cutting balusters on angle.
2
2.Set railing along the nose of the stair treads, making sure baluster holes are vertically aligned and mark line at each intersection. When measuring, cut equal lengths from each side of railing allowing a minimum of 2" (51 mm) on each end from the last baluster hole to the end of the rail. This will ensure proper baluster and bracket placement and equal spacing of balusters per each railing section.
3c. Cut the VERY END of
3c
baluster, both top and
bottom, making sure
that point to point measurement of the baluster remains at
32" (813 mm) or
38" (965 mm)
either 32" (813 mm) for
36" (914 mm) rail heights
or 38" (965 mm) for
42" (1067 mm) rail heights.
IMPORTANT NOTE REGARDING FOOT BLOCK INSTALLATION: . » Refer to detailed instructions (Trex
Select) rail instructions) included with foot block prior to installation of railing section as these include other required steps for proper installation.
SELECT RAILING
143
HOW TO INSTALL TREX SELECT STAIR RAILING/CONTINUED
TREX SELECT
Attaching Foot Block to Bottom Stair Rail
4. Invert the bottom stair
rail. Center and drill a
4
hole using a 3/16"
(5 mm) drill bit. This
will be location for foot
block (to be installed
last).
Lower Stair Post Locations
5d.Snap the bottom stair adaptor bracket
5d
(labeled BOTTOM) to
the standard bracket.
Repeat for remaining
bracket.
Attachment of Brackets to Railings
5a.Check fit for both
top and bottom
5a
railings in designated
positions for location
onto posts. Remove
railings.
Upper Stair Post Locations
5b.Snap the top stair
adaptor bracket
5b
(labeled TOP) to the
standard bracket.
Repeat for remaining
bracket.
5e
Top Rail
1
Bottom Rail 1
2
2
5e.On the TOP RAIL, attach the assembled bottom stair bracket to the side with baluster holes. On the BOTTOM RAIL, attach the assembled bottom stair bracket to the OPPOSITE SIDE of the baluster holes. Attach both brackets using three #8-18 x 1" self-drilling screws (provided).
SELECT RAILING
5c
Top Rail
1
Bottom Rail 1
2
2
5c.On the TOP RAIL, attach the assembled top stair bracket to the side with baluster holes. On the BOTTOM RAIL, attach the assembled top stair bracket to the OPPOSITE SIDE of the baluster holes. Attach both brackets using three #8-18 x 1" self-drilling screws (provided).
144 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
HOW TO INSTALL TREX SELECT STAIR RAILING/CONTINUED
TREX SELECT
Attachment of Bottom Rail to Post
6a
Attachment of Top Rail to Post 8a.Place top rail onto
balusters, allowing the 8a
top rail to rest on the surface of the balusters.
6a.Assemble a few of the balusters into the bottom and top railings (make sure balusters are setting at 90°) and set this on scrap material clearing the stair treads to determine where bracket locations need to be. Measure to make sure that the bottom railing will clear the stair treads and the top railing will be aligned with horizontal railing (remember in most cases, a longer post and post sleeve will be needed on the lower section of stair rail to accommodate stair angle).
6b.After locating
6b
appropriate position
for bottom rail remove
top rail and balusters
and attach bottom rail
stair bracket to upper
post using two #8-10
x 3" wood screws
(provided).
6c.Attach bottom stair
6c
rail stair bracket to
lower post using two
#8 10 x 3" wood
screws (provided).
For best results set
drill to low speed
when installing these
screws.
Install Balusters
7
7.Slide balusters into
bottom rail until
balusters are fully
seated.
8b
8c
8b.Attach top stair rail bracket to upper post using two #8-10 x 3" screws (provided). For best results set drill to low speed when installing these screws.
8c.Attach top stair rail bracket to lower post using two #8-10 x 3" screws (provided). For best results set drill to low speed when installing these screws.
Attaching Post Caps and Installing Foot Block
9.Secure post caps
with silicone or PVC
9
adhesive. Attach foot
block per foot block
2
instructions.
NOTE: Clean up any
excess adhesive before it
1
dries.
SELECT RAILING
145
TREX ALUMINUM ADA COMPLIANT HANDRAIL
STAIR APPLICATION
RAMP APPLICATION
ADA Handrail Guidelines
1.ADA handrails can be installed using various design applications such as those for stairs, ramps, and horizontal applications. Designs include options for straight and 90° wall returns, 90° corners, and adjustable angles. Choose which is best for your needs before installing. Refer to railing profiles (page 57) for a more detailed parts list.
34" (864 mm) to
38" (965 mm)
2.The handrail system top rail should be 34" (864 mm) to 38" (965 mm) above the surface. However, verifying height requirements with local building code officials before installing is important as codes vary in different areas.*
3.Maintain a minimum clearance of 1-1/2" (38 mm) between the handrail and any obstructions above or behind the handrail.
4.The end loop return at all landings must extend 12" (305 mm) past the end of the ramp or stair application.*
5.The slope of the handrail for the ramp should not exceed 1" (25 mm) rise over a 12" (305 mm) run.
6. The maximum recommended span between supports is 6' (1.83 m) on center. Thus, placement of posts is critical when installation of railing is being considered.* 7.Rails are designed to have a tight fit into other
connecting components. It is critical to line these up in the correct orientation BEFORE connecting parts together. If it is necessary to shift or move a component on a rail, wrap with a protective cloth to prevent scratching as you may need to use a widemouth wrench to correct this. 8.At any straight location where internal connector is used, it is CRITICAL to locate these as close to a wall mount as possible. 9.If using metal posts, pre-drill all locations for bracket attachment. (ALWAYS use a drill bit slightly SMALLER in diameter than the screw being used for attachment.) 10.A ll elbow components can be cut down to allow for tighter angles. Cut a maximum of 2" (51 mm) on each side if this is required.
*Refer to the American Disabilities Act for detailed information in regards to handrail requirements.
SAFETY NOTES
» When cutting metal, ALWAYS wear proper safety eyewear (as well as any other proper safety wear).
» R emove all burrs from cut ends before installation. » Use of a non-ferrous metal blade is recommended.
146 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ADA RAILING
ADA RAILING PROFILES
» S EE PAGE 58 FOR SKU NUMBERS.
DESCRIPTION
COLOR
ADA Hand Rail 1.385" (35 mm) diameter
BK, BZ, WT
ADA Wall Return
BK, BZ, WT
ADA Wall Mount
BK, BZ, WT
ADA Corner Mount*
BK, BZ, WT
DESCRIPTION ADA 90° Elbow
COLOR BK, BZ, WT
ADA 36°, 34°, and 31° Elbows
BK, BZ, WT
ADA 5° Elbow ADA Collar
BK, BZ, WT BK, BZ, WT
ADA End Cap
BK, BZ, WT
ADA Internal Connector
ADA Handrail Return
BK, BZ, WT
*Can only be used with metal post horizontal applications.
HARDWARE
RAIL TO BRACKET ATTACHMENT Short Metal Screw (#10 x 5/8" [16 mm])
BRACKET TO METAL POST ATTACHMENT Long Metal Screw (#12 x 1-1/4" [32 mm])
BRACKET TO WOOD POST/POST SLEEVE ATTACHMENT Wood Screw (8-10 x 2" [51 mm])
COLORS: BK Charcoal Black BZ Bronze WT White
NOTE: If attaching brackets to 6x6 posts/post sleeves, use 8-10 x 2-1/2" (64 mm) wood screws (not included).
147 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
ADA RAILING
HOW TO INSTALL TREX ALUMINUM ADA COMPLIANT HANDRAIL
90° Wall Return
3.Attach rail to wall mount using specific hardware provided (see chart on previous page).
4. Attach end cap to railing.
Rail-to-Rail Connections/Internal Connector
1. If required, cut railing to proper length based on location of wall return(s) or attachment to other components.
2.If desired, collar ring can be used to hide seam of wall return to rail. Slide this over rail BEFORE inserting rail into wall return.
3.Slide rail onto wall return until it is fully inserted and seam is hidden under collar (if collar is being used).
4. Attach wall return to post using specific hardware provided (see chart on previous page), ENSURING wall return is at proper angle of alignment to post. (Wall return is designed to have tight fit into rail, thus location of attachment is critical.) If using metal posts, pre-drill post prior to attachment of wall mount.
Wall Mount
NOTE: Refer to Rail-to-Rail Connections section if connecting two or more rails together to make continuous straight run.
1.If required, cut railing to proper length based on location of wall mount(s) or attachment to other components.
2.Attach wall mount to post using specific hardware provided (see chart on previous page), ENSURING wall mount is at proper angle of alignment to angle of rail. If using metal posts, pre-drill post prior to attachment of wall mount.
TIP: To help with angled attachment, place one screw into bottom hole of bracket and pivot wall mount to position required.
148
NOTE: When rail-to-rail straight connections are use for longer spans, posts must be installed 6' OC max. In addition, a wall mount MUST be used at each seam of rail-to-rail connections as close to center of wall mount as possible. If collar is used, this can be offset slightly to allow for the collar to fit.
1.If required, cut railing to proper length. 2.If desired, collar ring can be used to hide seam
between rails. Slide this over rail BEFORE inserting rails into internal connector. 3.Slide internal connector into rail end until metal spacer screw is touching either end of rail or the collar, if this was used. 4.Slide second rail over opposite end of internal connector, until this is touching metal spacer screw. 5.Remove metal spacer screw using #2 square-head screwdriver. 6.Push second rail further over internal connector until this fits in the collar (if used) or fits tightly against rail. 7.Attach wall mount to post per previous instructions. 8.Attach rail to wall mount per previous instructions. 9.Use end caps where required.
ADA RAILING
HOW TO INSTALL TREX ALUMINUM ADA COMPLIANT HANDRAIL/CONTINUED
Elbows (90°, 36°, 34°, 31°, 5°)
1.If required, cut railing to proper length based on location of elbows and other components being used.
2.If desired, collar ring can be used to hide seam of elbow to rail. Slide this over rail BEFORE inserting rail into elbow.
3.Slide internal connector into rail end until metal spacer screw is touching either end of rail or the collar, if this was used.
4.Slide appropriate angled elbow onto opposite end of internal connector, until this is touching metal spacer screw.
5.Remove metal spacer screw using #2 square head screwdriver.
6.Push elbow further over internal connector until this fits in the collar (if used) or fits tightly against rail.
7.Attach wall mount to post per previous instructions. 8.Attach rail to wall mount per previous instructions.
4.Attach wall return to lower end of handrail return (longer side), ENSURING wall return is at proper angle of alignment to post. (Wall return is designed to have tight fit into rail, thus location of attachment is critical.)
5.Slide opposite end of handrail return onto internal connector, until this is touching metal spacer screw.
6.Remove metal spacer screw using #2 square-head screwdriver.
7.Push handrail return further over internal connector until this fits in the collar (if used) or fits tightly against elbow.
8.Attach wall return to post per previous instructions. 9.Attach rail to wall mount per previous instructions. 10.U se end caps where required.
Corner Mount
Handrail Return 180°
NOTE: Ramp application shown here. (Appropriate angle elbow also required for stair applications.) 1.If required, cut railing to proper length based on
location of elbow used as well and other components being used. 2.If desired, collar ring can be used to hide seam of handrail return to rail or elbow being used. Slide this over rail BEFORE inserting rail into other component. 3.Ensure that all components are aligned to both wall mount on post as well as location of elbow on rail BEFORE attachment. 3.Slide internal connector into appropriate elbow being until metal spacer screw is touching either end of elbow or the collar, if this was used.
1. C orner mount can ONLY BE USED ON METAL POSTS and only for horizontal applications, such as stair landings.
2. P re-drill metal post and install corner post to metal post using specific hardware provided (see chart on previous page).
3. If desired, collar ring can be used to hide seam of elbow to rail. Slide this over rail BEFORE inserting rail into elbow (not shown in picture above).
3. S lide internal connector into rail end until metal spacer screw is touching either end of rail or the collar, if this was used.
4. S lide appropriate angled elbow onto opposite end of internal connector, until this is touching metal spacer screw.
5. R emove metal spacer screw using #2 square-head screwdriver.
6. P ush elbow further over internal connector until this fits in the collar (if used) or fits tightly against rail.
7. Install elbow to corner mount using specific hardware provided (see chart on page 147).
ADA RAILING
149 NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.
Adobe InDesign CC 13.1 (Macintosh) 3-Heights(TM) PDF Optimization Shell 4.8.25.2 (http://www -tools.com)