P43B0020a2 SMC-CR2021. 3. 33. 1. ST30-8PLUS. 38. P43B0030a2 SMC- ... minutes or placed in manual reset mode. Calibration – Can be calibrated to.
SMC-CR2021 SMC-CR3021 SMC-CR5021. 16 M9110WS. Total head in meters. ... Restart Delay – Can be set up to 225 minutes or placed in manual reset mode.
pentair commercial catalog PYROTENAX Commercial MI Wiring Cable - USESI Careers Availability: This item is currently not available. Nov18 nVent Integrates Advanced Work Packaging and Heat Mapping into 3D Electric Heat Tracing Design Software .
Myers®
PROFESSIONAL WATER SYSTEMS
PUMPS, TANKS, MOTORS AND CONTROLS
w w w.FEMYERS.com
PENTEK® XE Series
Performance Proven Line-Up
Performance Proven Myers® 4" Submersibles Now Feature the Pentek® XE Series Motors.
n E ngineered for extra efficiency
and durability.
n 2 -wire permanent split capacitor
design draws up to 22% fewer amps, patented toroidal capacitor reduces vibration and noise.
n P umps supplied with the XE Series
Motor are factory tested and comply with CSA CUS safety certifications.
n 3 -wire motors, when operated with a Pentek SMC-CR control box, draw 22% fewer amps, due to superior motor and controls technology.
22 UP
TO
%
LOWER AMP
DRAW
FINALLY, A MOTOR AS TOUGH AS OUR PUMPS
Table of Contents
4" SUBMERSIBLE PUMPS Predator Plus 4" Submersible Pumps.............................. 2-8 The Rustler 4" Submersible Pumps................................ 9-13 S Series Submersible Pumps......................................... 14-20 The Ranger 4" Submersible Pumps............................... 21-24
SUBMERSIBLE MOTORS and MOTOR CONTROLS Pentek® XESeries 4" Submersible
Motors......................................................................... 25-27 Cable Selection................................................................ 28-29 Submersible Motor Controls........................................... 30-31 Single-Phase Protectors....................................................... 32 The Insider SPP-111P and SPP-231P.................................. 33 SPP-111-3RLP, SPP-233P and SPP-235P.......................... 34 The Informer Pump Protection............................................. 35 Pentek IntellidriveTM........................................................... 36-37 Pentek IntellikitTM.............................................................. 38-39 PPC3 and PPC5............................................................... 40-41 6" Hitachi® Submersible Motor...................................... 42-44 6" Pentek® Submersible Motor...................................... 45-46
JET PUMPS MPNSeries Shallow Well................................................ 47-48 Quick Draw Shallow Well................................................ 49-50 MPLSeries........................................................................ 51-52 HR Series.......................................................................... 53-54 HJ Series Convertible...................................................... 55-58 HC and HCMSeries......................................................... 59-62
TANKS Pro-Source® Fibrewound Pressure................................ 63-65 Pro-Source Fibrewound.................................................. 66-67 Pro-Source Plus Premium Steel
Pressurized................................................................. 68-70 Pro-Source Steel Pressurized........................................ 71-75 Pro-Source Steel EpoxyLined......................................... 76-77
CENTRIFUGAL PUMPS Quick Prime Self-Priming 3/4 3 HP............................. 78-79 Quick Prime Self-Priming 5 HP...................................... 80-81 QPSeries Field Assembly Kits.............................................. 82 PQPSeries........................................................................ 83-84 CTSeries Crusader....................................................... 85-86 Centri-Thrift...................................................................... 87-90
BOOSTER PUMPS MPBSeries Servicable High Pressure
Booster........................................................................ 91-94
UTILITY PUMPS MSP Swimming Pool Pumps.......................................... 95-96 Composite Engine-Driven
Self-Priming Pump.................................................... 97-98 MES106 Utility Transfer Pump.............................................. 99
ACCESSORIES Pressure Switches............................................................... 100 Valves and Regulators................................................. 100-101 Well Adapters, Seals............................................................ 102
GENERAL INFORMATION Pipe Friction Loss Charts............................................ 103-104 Cable Selection Guide Hitachi®
6"-8" Submersible Motors.................................... 105-108 Cable Selection Guide Pentek®
6" Submersible Motors............................................ 109-110
Noryl® is a registered trademark of the General Electric Company. Nylatron® is a registered trademark of The Polymer Corporation. Teflon® is a registered trademark of E. I. du Pont de Nemours and Company Hitachi® is a registered trademark of Hitachi Industrial Equipment Systems Co., Ltd. All other brand or product names are trademarks or registered trademarks of Pentair Ltd.
1
4" Submersible pumps
Predator Plus
The Predator Plus Series 4" submersible pumps have a proven track record for reliability and performance, and are the preferred brand by many industry professionals. Stainless steel construction and self-lubricating impellers provide reliable performance under the most demanding conditions. The Predator Plus also features the Pentek® XE Series, high-thrust motor for increased efficiency and extended service life.
APPLICATIONS
n Water systems...residential, industrial, commercial, multiple housing and farm clean water use.
SPECIFICATIONS
Shell 300 Series Stainless Steel
Discharge 300 Series Stainless Steel
Discharge Bearing Nitrile rubber
Impellers Engineered composite
Diffusers Engineered composite
Suction Caps Engineered composite
Shaft and Coupling 300 Series Stainless Steel
Intake 300 Series Stainless Steel
Intake Screen 300 Series Stainless Steel
Cable Guard 300 Series Stainless Steel
Internal Check Valve Spring loaded
Fasteners 304 Stainless Steel
FEATURES
Nothing Better Top-of-the-line 4" submersible pump is unequalled in the marketplace.
Stainless Steel Shell, discharge bowl, shaft and coupling, wear ring and suction screen all lead-free.
Gritty Performance Self-lubricating impellers resist abrasion from grit and sand Teflon® impregnated staging proven to outlast the competition.
Supreme Power Features the highthrust Pentek XE motor for the ultimate in power, efficient performance and longer life. Thermal overload and lightning protected.
On the Job Field serviceable, threaded pump assembly.
An Eye for Safety Built-in eyelet for safety line connection.
Teflon® is a registered trademark of E. I. du Pont de Nemours and Company All other brand or product names are trademarks or registered trademarks of Pentair Ltd.
2
M9108WS
4" Submersible pumps
Predator Plus
OUTLINE DIMENSIONS
Pump End Length
Assembled Pump Length
PW3.u7idm8t"hp
CABLE SELECTION
THREE WIRE CABLE, 60 Hz (Service Entrance to Motor Maximum Length in Feet)
Motor Rating
HP
Volt
14
CSIR Control Boxes
1/2
115
87
1/2
230
348
3/4
230
264
1
230
226
CSCR Control Boxes
1/2
230
447
3/4
230
348
1
230
304
1 1/2
230
197
2
230
180
3
230
133
5
230
12
10
8
Wire Size, AWG
6
4
3
138
221
349
544
867
1090
553
883
1398
2175
3467
4359
420
670
1061
1651
2632
3309
359
573
908
1413
2252
2831
711
1135
1797
2796
4458
5604
553
883
1398
2175
3467
4359
484
772
1223
1903
3034
3814
314
501
793
1234
1968
2474
286
456
722
1123
1790
2251
211
337
534
830
1324
1664
206
326
507
809
1017
2
1
0
1376
1734
2188
5505
6935
8753
4178
5264
6644
3575
4504
5685
7078
8916
11254
5505
6935
8753
4817
6068
7659
3124
3936
4968
2843
3581
4520
2102
2648
3342
1284
1618
2042
00
2761
8383 7173
11044 9663 6268 5703 4217 2577
TWO WIRE CABLE, 60 Hz (Service Entrance to Motor Maximum Length in Feet)
Motor Rating
Wire Size, AWG
HP
Volt
14
12
10
8
6
4
3
2
1
0
00
1/2
115
115
183
293
463
721
1150
1445
1825
2299
2902
3662
1/2
230
466
742
1183
1874
2915
4648
5843
7379
9295
11733
3/4
230
342
545
869
1376
2141
3413
4291
5419
6826
8617
10871
1
230
241
383
611
968
1506
2400
3018
3811
4801
6060
7646
1 1/2
230
199
317
505
801
1246
1986
2496
3153
3972
5013
6325
3
M9108WS
4" Submersible pumps
Predator Plus
ORDERING INFORMATION
Motor GPM Type
HP Stg. PH
1/2 11 1
1/2 11 1
2-Wire 3/4 15
1
1
19
1
1-1/2 26 1 5
1/2 11 1
1/2 11 1
3-Wire 3/4 15 1
1
19 1
1-1/2 26 1
1/2
9
1
1/2
9
1
2-Wire 3/4 12 1
1
15 1
1-1/2 20 1
1/2
9
1
8
1/2
9
1
3/4 12 1
3-Wire 1
15 1
1-1/2 20 1
2
24 1
3
33 1
1/2 7
1
1/2 7
1
2-Wire 3/4 9
1
1
11 1
1-1/2 16 1
1/2 7
1
12
1/2 7
1
3/4 9
1
1
11 1
3-Wire
1-1/2 16 1
2
19 1
3
25 1
5
37 1
*Length and weight are approximate.
Assembled Pump
Volt Catalog Number 115 2ST51-5PLUS-P4
2ST52-5PLUS-P4 2ST72-5PLUS-P4 230 2ST102-5PLUS-P4 2ST152-5PLUS-P4 115 3ST51-5PLUS-P4 3ST52-5PLUS-P4 3ST72-5PLUS-P4 230 3ST102-5PLUS-P4 3ST152-5PLUS-P4 115 2ST51-8PLUS-P4 2ST52-8PLUS-P4 2ST72-8PLUS-P4 230 2ST102-8PLUS-P4 2ST152-8PLUS-P4 115 3ST51-8PLUS-P4 3ST52-8PLUS-P4 3ST72-8PLUS-P4 3ST102-8PLUS-P4 230 3ST152-8PLUS-P4
Length Inches* 22-1/2 22-1/2 26-1/2 30-1/2
39 22-1/2 22-1/2 26-1/2 30-1/2
39 22 22 26 29-1/2 37 22 22 26 29-1/2 35
115 2ST51-12PLUS-P4
21
2ST52-12PLUS-P4
21
2ST72-12PLUS-P4
24
230
2ST102-12PLUS-P4
27
2ST152-12PLUS-P4 34-1/2
115 3ST51-12PLUS-P4
21
3ST52-12PLUS-P4
21
3ST72-12PLUS-P4
24
3ST102-12PLUS-P4
27
230 3ST152-12PLUS-P4
33
Pump End
Pentek® Motor Control Box
Weight Pounds*
Catalog Number
36
ST5-5PLUS
36
ST5-5PLUS
40
ST72-5PLUS
45
ST10-5PLUS
54
ST15-5PLUS
33
ST5-5PLUS
33
ST5-5PLUS
37
ST72-5PLUS
43
ST10-5PLUS
52
ST15-5PLUS
35
ST5-8PLUS
35
ST5-8PLUS
39
ST7-8PLUS
42
ST10-8PLUS
49
ST15-8PLUS
33
ST5-8PLUS
33
ST5-8PLUS
36
ST7-8PLUS
42
ST10-8PLUS
50
ST15-8PLUS
ST20-8PLUS
ST30-8PLUS
34
ST5-12PLUS
34
ST5-12PLUS
38
ST7-12PLUS
44
ST10-12PLUS
51
ST15-12PLUS
33
ST5-12PLUS
33
ST5-12PLUS
36
ST7-12PLUS
41
ST10-12PLUS
48
ST15-12PLUS
ST20-12PLUS
ST30-12PLUS
ST50-12PLUS
Length Inches*
13 13 16 18-1/2 23-1/2 13 13 16 18-1/2 23-1/2 12-1/2 12-1/2 15 17-1/2 21-1/2 12-1/2 12-1/2 15 17-1/2 21-1/2 31 38 11-1/2 11-1/2 13-1/2 15 19-1/2 11-1/2 11-1/2 13-1/2 15 19-1/2 28 33 41-1/2
Catalog Number
Catalog Number
P42B0005A1
P42B0005A2
P42B0007A2
P42B0010A2
P42B0015A2
P43B0005A1
--
P43B0005A2 SMC-CR0521
P43B0007A2 SMC-CR0721
P43B0010A2 SMC-CR1021
P43B0015A2 SMC-CR1521
P42B0005A1
P42B0005A2
P42B0007A2
P42B0010A2
P42B0015A2
P43B0005A1
--
P43B0005A2 SMC-CR0521
P43B0007A2 SMC-CR0721
P43B0010A2 SMC-CR1021
P43B0015A2 SMC-CR1521
P43B0020A2 SMC-CR2021
P43B0030A2 SMC-CR3021
P42B0005A1
P42B0005A2
P42B0007A2
P42B0010A2
P42B0015A2
P43B0005A1
--
P43B0005A2 SMC-CR0521
P43B0007A2 SMC-CR0721
P43B0010A2 SMC-CR1021
P43B0015A2 SMC-CR1521
P43B0020A2 SMC-CR2021
P43B0030A2 SMC-CR3021
P43B0050A2 SMC-CR5021
4
M9108WS
4" Submersible pumps
Predator Plus
ORDERING INFORMATION
Assembled Pump
Pump End
Pentek® Motor Control Box
Motor GPM Type
HP Stg. PH
1/2
4
1
1/2
4
1
2-Wire 3/4
6
1
1
8
1
1-1/2 11 1
1/2
4
1
20
1/2
4
1
3/4
6
1
1
8
1
3-Wire
1-1/2 11 1
2
14 1
3
18 1
5
29 1
Volt Catalog Number 115 2ST51-20PLUS-P4
2ST52-20PLUS-P4
Length Inches*
19 19
Weight Pounds*
32 32
Catalog Number
ST5-20PLUS ST5-20PLUS
Length Inches*
9-1/2 9-1/2
Catalog Number
P42B0005A1 P42B0005A2
Catalog Number
2ST72-20PLUS-P4 22-1/2 230
2ST102-20PLUS-P4 25-1/2
37
ST7-20PLUS 11-1/2 P42B0007A2
41
ST10-20PLUS
14
P42B0010A2
2ST152-20PLUS-P4
32
48
ST15-20PLUS
17
P42B0015A2
115 3ST51-20PLUS-P4
19
31
ST5-20PLUS
9-1/2 P43B0005A1
--
3ST52-20PLUS-P4
19
31
ST5-20PLUS
9-1/2 P43B0005A2 SMC-CR0521
3ST72-20PLUS-P4 22-1/2
34
ST7-20PLUS 11-1/2 P43B0007A2 SMC-CR0721
3ST102-20PLUS-P4 25-1/2
39
ST10-20PLUS
14
P43B0010A2 SMC-CR1021
230 3ST152-20PLUS-P4 30-1/2
46
ST15-20PLUS
17
P43B0015A2 SMC-CR1521
ST20-20PLUS
25
P43B0020A2 SMC-CR2021
ST30-20PLUS
29
P43B0030A2 SMC-CR3021
ST50-20PLUS
42
P43B0050A2 SMC-CR5021
*Length and weight are approximate.
5
M9108WS
Total head in meters
4" Submersible pumps
Predator Plus
Total head in feet
PUMP PERFORMANCE 5 GPM
Capacity liters per minute
0
5
10 15 20 25 30 35
1200 350
1000
300
800
1-1/2 HP
250
1 HP
200
600
3/4 HP
150
400
1/2 HP
100
200 50
0
0
2
4
6
8
10
Capacity gallons per minute
PUMP PERFORMANCE 12 GPM
0 1200
Capacity liters per minute
25
50
5 HP
1000
3 HP
800
2 HP
600
1-1/2 HP
400
1 HP
3/4 HP 1/2 HP
200
0
5
10
15
Capacity gallons per minute
75 350 300 250 200 150 100 50 0
20
Total head in meters Total head in feet
Total head in meters Total head in feet
PUMP PERFORMANCE 8 GPM
0 1200
1000
Capacity liters per minute
10
20
30
40
3 HP
50 350 300
800
2 HP
250
1-1/2 HP
200
600
1 HP
150
400
3/4 HP
1/2 HP
100
200 50
0
0
2
4
6
8
10
12
14
Capacity gallons per minute
PUMP PERFORMANCE 20 GPM
0 1200
Capacity liters per minute
25
50
75
100
350
1000
5 HP
800
600
3 HP
2 HP
400
1-1/2 HP
1 HP
200
3/4 HP
1/2 HP
0
5
10
15
20
25
Capacity gallons per minute
300 250 200 150 100 50 0 30
Total head in feet
Total head in meters
6
M9108WS
4" Submersible pumps
Predator Plus
PUMPPERFORMANCE
HP
2-Wire Cat. No.
5 GALLONS PERMINUTE
1/2
2ST51-5PLUS-P4* 2ST52-5PLUS-P4
3-Wire Cat. No.
Tank
Pumping Depth in Feet
Pres. 20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750
3ST51-5PLUS-P4* 3ST52-5PLUS-P4
20/40 30/50 40/60
7.4 7.0 6.6 6.2 5.8 5.3 3.7 7.3 6.9 6.5 6.2 5.7 5.2 4.6 7.3 6.9 6.5 6.3 5.6 5.2 4.6 3.9
3/4 2ST72-5PLUS-P4
20/40 3ST72-5PLUS-P4 30/50
40/60
7.4 7.2 6.8 6.1 5.3 4.2 7.4 7.2 6.8 6.6 5.7 4.8 3.5 7.3 7.1 6.7 6.5 6.2 5.3 4.3
20/40 1 2ST102-5PLUS-P4 3ST102-5PLUS-P4 30/50
40/60
7.1 6.5 5.9 5.3 4.4 3.3 7.4 6.8 6.3 5.6 4.9 3.9 2.5 7.4 7.2 6.6 6.0 5.3 4.6 3.4
1-1/2 2ST152-5PLUS-P4
20/40 3ST152-5PLUS-P4 30/50
40/60
7.3 6.9 6.5 6.0 5.5 5.0 4.4 3.6 2.4 7.4 7.0 6.6 6.2 5.7 5.2 4.7 4.0 3.0 7.3 6.8 6.5 6.0 5.5 5.0 4.4 3.6 2.4
8 GALLONS PERMINUTE
1/2
2ST51-8PLUS-P4* 2ST52-8PLUS-P4
3ST51-8PLUS-P4* 3ST52-8PLUS-P4
20/40 30/50 40/60
11.0 10.3 9.5 8.5 7.5 6.0 10.8 10.1 9.3 8.3 7.2 5.8 10.8 10.1 9.3 8.3 7.1 5.7
3/4 2ST72-8PLUS-P4
20/40 3ST72-8PLUS-P4 30/50
40/60
10.7 10.2 9.6 9.0 6.8 10.6 10.0 9.5 8.8 8.0 5.5 10.6 10.0 9.5 8.8 8.0 7.1
20/40 1 2ST102-8PLUS-P4 3ST102-8PLUS-P4 30/50
40/60
11.0 10.6 9.3 7.9 5.8 10.9 10.5 10.0 8.7 7.0 4.7 10.9 10.5 10.0 9.5 8.1 6.2
1-1/2 2ST152-8PLUS-P4
20/40 3ST152-8PLUS-P4 30/50
40/60
11.1 10.4 9.5 8.4 7.2 5.5 10.7 10.0 9.0 7.7 6.3 4.6 10.5 9.6 8.5 7.3 5.7
20/40
2
ST20-8PLUS
30/50
40/60
10.8 10.0 9.2 8.3 7.2 6.0 11.0 10.5 9.7 8.9 7.9 6.7 5.4 10.8 10.1 9.3 8.4 7.3 6.0
20/40
3
ST30-8PLUS
30/50
40/60
10.8 10.3 9.8 9.1 8.5 7.7 11.0 10.6 10.1 9.5 8.9 8.2 7.5 10.9 10.4 9.8 9.2 8.5 7.8 7.0
12 GALLONS PERMINUTE
1/2
2ST51-12PLUS-P4* 2ST52-12PLUS-P4
3ST51-12PLUS-P4* 3ST52-12PLUS-P4
20/40 30/50 40/60 14.5
14.5 13.0
15.0 13.0 11.5
13.5 11.5 9.8
12.0 9.8
10.3 7.2
8.0
3/4 2ST72-12PLUS-P4
20/40 3ST72-12PLUS-P4 30/50
40/60
15.7 14.7 13.7 12.6 11.2 9.8 8.0 15.5 14.5 13.4 12.2 10.9 9.4 7.5 15.5 14.5 13.4 12.2 10.9 9.4 7.5
20/40 1 2ST102-12PLUS-P4 3ST102-12PLUS-P4 30/50
40/60
15.5 14.7 13.7 12.7 11.9 8.7 15.3 14.5 13.5 12.6 11.6 10.5 15.3 14.5 13.5 12.6 11.6 10.5 9.2
20/40 1-1/2 2ST152-12PLUS-P4 3ST152-12PLUS-P4 30/50
40/60
15.6 14.2 12.6 10.8 8.5 15.4 14.9 13.4 11.7 9.7 15.4 14.9 14.3 12.8 11.0 8.8
20/40
2
ST20-12PLUS
30/50
40/60
14.5 13.1 11.7 10.0 8.0 15.0 13.8 12.5 10.9 9.0 14.5 13.3 11.9 10.2 8.3
20/40
3
ST30-12PLUS
30/50
40/60
14.8 13.8 12.7 11.6 10.5 9.0 15.2 14.3 13.3 12.2 11.0 9.7 14.9 13.9 12.9 11.7 10.5 9.1
All pumps wired for 230 volt operation. Values based on 1" minimum diameter pipe. *These 1/2 HP pumps are available with 115 Volt motors.
7
M9108WS
4" Submersible pumps
Predator Plus
PUMPPERFORMANCE
HP
2-Wire Cat. No.
20 GALLONS PERMINUTE
3-Wire Cat. No.
3/4 2ST72-20PLUS-P4 3ST72-20PLUS-P4
Tank
Pumping Depth in Feet
Pres. 20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750
20/40 23.5 22.0 20.0 17.0 30/50 21.5 19.5 16.0 40/60 19.5 16.0
1
2ST10220PLUS-P4
20/40
24.5 23.0 22.0 20.5 18.0 15.5
3ST102-20PLUS-P4 30/50 24.0 23.0 21.5 20.0 17.5 14.5
40/60 23.0 21.5 20.0 17.5 14.5
1-1/2
2ST15220PLUS-P4
20/40 3ST152-20PLUS-P4 30/50
40/60
24.5 23.5 22.5 21.5 20.5 19.0 17.0 24.5 23.5 22.5 21.5 20.0 18.5 16.5 14.5 24.5 23.5 22.5 21.5 20.0 18.5 16.5 14.5 12.5
20/40
23.6 23.0 22.4 21.5 19.0 15.0
2
ST20-20PLUS
30/50
23.6 23.0 22.2 21.3 20.5 17.0
40/60
23.6 23.0 22.2 21.3 20.4 19.3 15.5
20/40
3
ST30-20PLUS
30/50
40/60
24.5 23.7 22.4 20.8 18.5 15.4 23.7 23.1 22.5 21.0 18.8 15.5 24.0 23.6 23.1 22.5 21.0 18.8 15.8
20/40
5
ST50-20PLUS
30/50
40/60
24.0 23.2 22.3 21.5 20.0 18.7 17.0 15.0 24.4 23.6 22.8 22.0 20.8 19.5 17.7 16.0 24.0 23.3 22.4 21.4 20.2 18.8 17.0 15.0
All pumps wired for 230 volt operation. Values based on 1" minimum diameter pipe. *These 1/2 HP pumps are available with 115 Volt motors.
8
M9108WS
4" Submersible pumps
The Rustler
The Rustler 4" submersible pump is one of the most popular models in the Myers® line. They have an exceptional history of durability and trouble-free operation. Stainless steel design and self-lubricating impellers offer the best service for extreme conditions. The Rustler also includes the Pentek® XE Series, high-thrust motor for efficient performance and years of extended service.
APPLICATIONS
n Water systems... residential, industrial, commercial, multiple housing and farm clean water use
SPECIFICATIONS
S hell 300 Series Stainless Steel
Discharge High-density composite resin
Discharge Bearing Nylatron®
I mpellers Engineered composite
Diffusers Engineered composite
Suction Caps Engineered composite
Shaft and Coupling 300 Series Stainless Steel
Intake Screen Highdensity composite resin
Cable Guard PVC
Check Valve Acetal
Fasteners 300 Series Stainless Steel
FEATURES
Leading Performer Premium 4" submersible pump series field proven and preferred by industry pros.
True Grit Self-lubricating impellers resist abrasion from grit and sand outlasts the competition.
Awesome Power Features the high-thrust Pentek XE motor for the ultimate in power, efficient performance and longer life. Thermal overload and lightning protected.
Built-in Safety Built-in eyelet for safety line connection.
Nylatron® is a registered trademark of The Polymer Corporation. All other brand or product names are trademarks or registered trademarks of Pentair Ltd.
9
M9109WS
4" Submersible pumps
The Rustler
OUTLINE DIMENSIONS
Pump End Length
Assembled Pump Length
Pump Width
CABLE SELECTION
THREE WIRE CABLE, 60 Hz (Service Entrance to Motor Maximum Length in Feet)
Motor Rating
AWG Copper Wire Size
Volts
HP
14
12
10
8
6
4
3
2
1
0
00
115
1/2
87
138
221
349
544
867
1090
1376
1734
2188
2761
1/2
348
553
883
1398
2175
3467
4359
5505
6935
8753
11044
3/4
264
420
670
1061
1651
2632
3309
4178
5264
6644
8383
230
1
226
359
573
908
1413
2252
2831
3575
4504
5685
7173
1-1/2
197
314
501
793
1234
1968
2474
3124
3936
4968
6268
TWO WIRE CABLE, 60 Hz (Service Entrance to Motor Maximum Length in Feet)
Motor Rating
Volts
HP
14
115
1/2
115
1/2
466
3/4
342
230
1
241
1-1/2
199
AWG Copper Wire Size
12
10
8
6
4
3
2
1
0
00
183
293
463
721
1150
1445
1825
2299
2902
3662
742
1183
1874
2915
4648
5843
7379
9295
11733
14803
545
869
1376
2141
3413
4291
5419
6826
8617
10871
383
611
968
1506
2400
3018
3811
4801
6060
7646
317
505
801
1246
1986
2496
3153
3972
5013
6325
10
M9109WS
4" Submersible pumps
The Rustler
ORDERING INFORMATION
GPM Motor Type HP
Stg.
1/2
11
1/2
11
2-Wire
3/4
15
1
19
5
1/2
11
1/2
11
3-Wire
3/4
15
1
19
1/2
9
1/2
9
2-Wire
3/4
12
1
15
1-1/2
20
8
1/2
9
1/2
9
3-Wire
3/4
12
1
15
1-1/2
20
1/2
7
1/2
7
2-Wire
3/4
9
1
11
1-1/2
16
12
1/2
7
1/2
7
3-Wire
3/4
9
1
11
1-1/2
16
3/4
6
2-Wire
1
8
1-1/2
11
20
3/4
6
3-Wire
1
8
1-1/2
11
*Length and weight are approximate.
Assembled Pump
Pump End Pentek® Motor Control Box
Length Weight Catalog Length Catalog PH Volt Catalog Number Inches* Pounds* Number Inches* Number
Catalog Number
1
115 2NFL51-5-P4
24-3/4
33
N55R 15-1/4 P42B0005A1
1
2NFL52-5-P4
24-3/4
33
N55R 15-1/4 P42B0005A2
1
230 2NFL72-5-P4
28-3/4
35
N75R
18 P42B0007A2
1
2NFL102-5-P4 32-1/2
1
115 3NFL51-5-P4
24-3/4
42
N105R 20-3/4 P42B0010A2
30
N55R 15-1/4 P43B0005A1
SMC-IR0511
1
3NFL52-5-P4
24-3/4
30
N55R 15-1/4 P43B0005A2
SMC-CR0521
1
230 3NFL72-5-P4
28-3/4
34
N75R
18 P43B0007A2
SMC-CR0721
1
3NFL102-5-P4 32-1/2
39
N105R 20-3/4 P43B0010A2
SMC-CR1021
1
115 2NFL51-8-P4
24-1/2
31
N58R
15 P42B0005A1
1
2NFL52-8-P4
24-1/2
31
N58R
15 P42B0005A2
1
2NFL72-8-P4
27-3/4
230
1
2NFL102-8-P4 31-1/2
35
N78R
17 P42B0007A2
40
N108R 19-3/4 P42B0010A2
1
2NFL152-8-P4 38-3/4
49
N158R 23-1/2 P42B0015A2
1
115 3NFL51-8-P4
24-1/2
29
N158R 15 P43B0005A1
SMC-IR0511
1
3NFL52-8-P4
24-1/2
29
N58R
15 P43B0005A2
SMC-CR0521
1
3NFL72-8-P4
27-3/4
230
1
3NFL102-8-P4 31-1/2
33
N78R
17 P43B0007A2
SMC-CR0721
37
N108R 19-3/4 P43B0010A2
SMC-CR1021
1
3NFL152-8-P4
37
39
N158R 23-1/2 P43B0015A2
SMC-CR1521
1
115 2NFL51-12-P4 23-1/4
29
N512R 13-3/4 P42B0005A1
1
2NFL52-12-P4 23-1/4
29
N512R 13-3/4 P42B0005A2
1
2NFL72-12-P4 26-1/4
230
1
2NFL102-12-P4 29
34
N712R 15-1/2 P42B0007A2
38
N1012R 17-1/4 P42B0010A2
1
2NFL152-12-P4 36-3/4
45
N1512R 21-1/2 P42B0015A2
1
115 3NFL51-12-P4 23-1/4
28
N512R 13-3/4 P43B0005A1
SMC-IR0511
1
3NFL52-13-P4 23-1/4
28
N512R 13-3/4 P43B0005A2
SMC-CR0521
1
3NFL72-12-P4 26-1/4
230
1
3NFL102-12-P4 29
33
N712R 15-1/2 P43B0007A2
SMC-CR0721
36
N1012R 17-1/2 P43B0010A2
SMC-CR1021
1
3NFL152-12-P4 35
43
N1512R 21-1/2 P43B0015A2
SMC-CR1521
1
2NFL72-20-P4 25-1/2
31
N720R 13-3/4 P42B0007A2
1
2NFL102-20-P4 27-1/2
36
N1020R 15-3/4 P42B0010A2
1
2NFL152-20-P4 34-1/4
230
1
3NFL72-20-P4 25-1/2
43
N1520R 19 P42B0015A2
31
N720R 13-3/4 P43B0007A2
SMC-CR0721
1
3NFL102-20-P4 27-1/2
35
N1020R 15-3/4 P43B0010A2
SMC-CR1021
1
3NFL152-20-P4 32-1/2
41
N1520R 19 P43B0015A2
SMC-CR1521
11
M9109WS
Total head in meters
4" Submersible pumps
The Rustler
Total head in feet
PUMP PERFORMANCE 5 GPM
Capacity liters per minute
0
5
10 15 20 25 30 35
700
1 HP
200
600
500 3/4 HP
150
400 1/2 HP
100 300
200 50
100
0
0
2
4
6
8
10
Capacity gallons per minute
PUMP PERFORMANCE 12 GPM
0 700
Capacity liters per minute
25
50
600
1-1/2 HP
500
400
1 HP
3/4 HP
300
1/2 HP
200
100
0
4
8
12
16
Capacity gallons per minute
75 200
150
100
50
0 20
Total head in feet
Total head in meters Total head in feet
Total head in meters Total head in feet
PUMP PERFORMANCE 8 GPM
0 700
600
Capacity liters per minute
10
20
30
40
1-1/2 HP
500
1 HP
400
3/4 HP
300
1/2 HP
50 200 150 100
200 50
100
0
0
2
4
6
8
10
12
14
Capacity gallons per minute
PUMP PERFORMANCE 20 GPM
Capacity liters per minute
0
20
40
60
80
100
400
120
1-1/2 HP
350
100
300
1 HP
80 250
3/4 HP
200
60
150 40
100
20 50
0
0
5
10
15
20
25
30
Capacity gallons per minute
Total head in meters
12
M9109WS
4" Submersible pumps
The Rustler
PUMP PERFORMANCE
HP
2-Wire Cat. No.
5 GALLONS PERMINUTE
3-Wire Cat. No.
1/2
2NFL51-5-P4* 2NFL52-5-P4
3NFL51-5-P4* 3NFL52-5-P4
3/4 2NFL72-5-P4
3NFL72-5-P4
1 2NFL102-5-P4 3NFL102-5-P4
8 GALLONS PERMINUTE
1/2
2NFL51-8-P4* 2NFL52-8-P4
3NFL51-8-P4* 3NFL52-8-P4
3/4 2NFL72-8-P4
3NFL72-8-P4
1 2NFL102-8-P4 3NFL102-8-P4
1-1/2 2NFL152-8-P4 3NFL152-8-P4
12 GALLONS PERMINUTE
1/2
2NFL51-12-P4* 2NFL52-12-P4
3NFL51-12-P4* 3NFL52-12-P4
3/4 2NFL72-12-P4 3NFL72-12-P4
1 2NFL102-12-P4 3NFL102-12-P4
1-1/2 2NFL152-12-P4 3NFL152-12-P4 20 GALLONS PERMINUTE 3/4 2NFL72-20-P4 3NFL72-20-P4
1 2NFL102-20-P4 3NFL102-20-P4
1-1/2 2NFL152-20-P4 3NFL152-20-P4
Tank
Pumping Depth in Feet
Pres. 20 40 60 80 100 120 140 160 180 200 250 300 350 400
20/40 30/50 40/60
20/40 30/50 40/60
20/40 30/50 40/60
6.6 6.2 5.8 5.3 3.7 6.5 6.2 5.7 5.2 4.6 6.5 6.3 5.6 5.2 4.6 3.9
6.1 5.3 4.2 6.6 5.7 4.8 3.5 6.7 6.5 6.2 5.3 4.3
6.5 5.9 5.3 6.3 5.6 4.9 6.6 6.0 5.3 4.6
20/40 30/50 40/60
20/40 30/50 40/60
20/40 30/50 40/60
20/40 30/50 40/60
11.0 10.3 9.5 8.5 7.5 6.0 10.8 10.1 9.3 8.3 7.2 5.8 10.8 10.1 9.3 8.3 7.1 5.7
11.2 10.7 10.2 9.6 9.0 6.8 11.1 10.6 10.0 9.5 8.8 8.0 5.5 11.1 10.6 10.0 9.5 8.8 8.0 7.1
11.0 10.6 9.3 7.9 5.8 10.9 10.5 10.0 8.7 7.0 4.7 10.9 10.5 10.0 9.5 8.1 6.2
11.1 10.4 9.5 8.4 10.7 10.0 9.0 7.7 10.5 9.6 8.5 7.3
20/40
15.0 13.5 12.0 10.3 8.0
30/50
14.5 13.0 11.5 9.8 7.2
40/60 14.5 13.0 11.5 9.8
20/40 30/50 40/60
15.7 14.7 13.7 12.6 11.2 9.8 8.0 15.5 14.5 13.4 12.2 10.9 9.4 7.5 15.5 14.5 13.4 12.2 10.9 9.4 7.5
20/40 30/50 40/60
15.5 14.7 13.7 12.7 11.9 8.7 15.3 14.5 13.5 12.6 11.6 10.5 15.3 14.5 13.5 12.6 11.6 10.5 9.2
20/40 30/50 40/60
15.6 14.2 12.6 10.8 8.5 15.4 14.9 13.4 11.7 9.7 15.4 14.9 14.3 12.8 11.0 8.8
20/40 23.5 22.0 20.0 17.0 30/50 21.5 19.5 16.0 40/60 19.5 16.0
20/40
24.5 23.0 22.0 20.5 18.0 15.5
30/50 24.0 23.0 21.5 20.0 17.5 14.5
40/60 23.0 21.5 20.0 17.5 14.5
20/40 30/50 40/60
24.5 23.5 22.5 21.5 20.5 19.0 17.0 24.5 23.5 22.5 21.5 20.0 18.5 16.5 14.5 24.5 23.5 22.5 21.5 20.0 18.5 16.5 14.5 12.5
450 500
4.4 3.3 3.9 2.5 3.4
7.2 5.5 6.3 4.6 5.7
All pumps wired for 230 volt operation. Values based on 1" minimum diameter pipe. *These 1/2 HP pumps are available with 115 Volt motors.
13
M9109WS
4" Submersible pumps
S Series
The S Series 4" submersibles have been a successful entry in the Myers® well pump line for many years and have a history of tremendous reliability. The all stainless steel construction is ideal for extreme water conditions and easily resists harmful corrosion. The S Series subs are also available with high-performance Pentek® motors for the very best in efficiency and trouble-free operation.
APPLICATIONS
n Water systems... residential, industrial, commercial, multiple housing and farm clean water use
SPECIFICATIONS
Straps 300 Series Stainless Steel
Discharge 300 Series Stainless Steel
Discharge Bearing Rubber
Impellers 300 Series Stainless Steel
Diffusers 300 Series Stainless Steel
Suction Caps 300 Series Stainless Steel
Shaft and Coupling 300 Series Stainless Steel
Intake 300 Series Stainless Steel
Intake Screen 300 Series Stainless Steel Stainless Steel
Cable Guard 300 Series Stainless Steel Stainless Steel
Check Valve 300 Series Stainless Steel
Fasteners 300 Series Stainless Steel Stainless Steel
FEATURES
Smooth and Quiet Precisioncrafted, 4" submersible well pumps for quieter operation.
Stainless Steel Everywhere Shell, impellers, discharge bowl, shaft and coupling, wear ring and suction screen.
Tough in Any Situation Stainless steel impellers stand tough against sand and grit nothing but the best.
All Powerful Features applicationmatched Pentek motors for just the right mix of performance and efficiency.
No Slip-ups Built-in hook assembly keeps pump safe from slip.
14
M9110WS
4" Submersible pumps
S Series
ORDERING INFORMATION
Motor
GPM
Type
2-Wire
5 3-Wire
2-Wire
10 3-Wire
2-Wire
16 3-Wire
HP
1/2 3/4 1 1-1/2 1/2 3/4 1 1-1/2 2 3 1/2 1/2 3/4 1 1-1/2 1/2 1/2 3/4 1 1-1/2 2 3 5 1/2 1/2 3/4 1 1-1/2 1/2 1/2 3/4 1 1-1/2 2 3 5
Assembled Pump
Volt Catalog Number
Length Inches*
2S52-5-P4 230 2S72-5-P4
2S102-5-P4 2S152-5-P4
26-3/8 31-1/2 36-1/4 45-1/8
3S52-5-P4 3S72-5-P4 3S102-5-P4 230 3S152-5-P4
22-3/8 31-1/2 36-1/4 43-1/8
115 2S51-10-P4 2S52-10-P4 2S72-10-P4
230 2S102-10-P4 2S152-10-P4
115 3S51-10-P4 3S52-10-P4 3S72-10-P4 3S102-10-P4
230 3S152-10-P4
23 23 26-1/2 30-1/2 39 23 23 26-1/2 30-1/2 37
115 2S51-16-P4 2S52-16-P4 2S72-16-P4
230 2S102-16-P4 2S152-16-P4
115 3S51-16-P4 3S52-16-P4 3S72-16-P4 3S102-16-P4
230 3S152-16-P4
21-3/4 21-3/4 23-1/4 28-3/8 33-1/8 21-3/4 21-3/4 23-1/4 28-3/8 31-1/8
*Length and weight are approximate.
DISCHARGESIZES: · The 5, 10 and 16 gallon SST pumps have 1-1/4" discharge · The 25, 40 and 75 gallon SST pumps have 2" discharge
Weight Pounds*
29 33 38 48 29 33 38 48
25 25 29 33 43 25 25 29 33 43
23 23 27 31 42 23 23 27 31 42
Pump End
Catalog Number
Length Inches*
S5-5 S7-5 S10-5 S15-5
16-7/8 21
24-1/4 29-5/8
S5-5 S7-5 S10-5 S15-5 S20-5 S30-5
16-7/8 21
24-1/4 29-5/8 40-3/4 50-1/8
S5-10 S5-10 S7-10 S10-10 S15-10
13-1/2 13-1/2
16 18-1/2 23-1/2
S5-10 S5-10 S7-10 S10-10 S15-10 S20-10 S30-10 S50-10
13-1/2 13-1/2
16 18-1/2 23-1/2 30-3/8 36-1/4 48-1/8
S5-16 S5-16
12-1/2 12-1/4
S7-16
12-3/4
S10-16
16-3/8
S15-16
17-5/8
S5-16 S5-16 S7-16 S10-16 S15-16 S20-16 S30-16 S50-16
12-1/4 12-1/4 13-3/4 16-3/8 17-5/8
21 26 39-7/8
Pentek® Motor Catalog Number
P42B0005A2 P42B0007A2 P42B0010A2 P42B0015A2 P43B0005A2 P43B0007A2 P43B0010A2 P43B0015A2 P43B0020A2 P43B0030A2 P42B0005A1 P42B0005A2 P42B0007A2 P42B0010A2 P42B0015A2 P43B0005A1 P43B0005A2 P43B0007A2 P43B0010A2 P43B0015A2 P43B0020A2 P43B0030A2 P43B0050A2 P42B0005A1 P42B0005A2 P42B0007A2 P42B0010A2 P42B0015A2 P43B0005A1 P43B0005A2 P43B0007A2 P43B0010A2 P43B0015A2 P43B0020A2 P43B0030A2 P43B0050A2
Control Box Catalog Number
SMC-CR0521 SMC-CR0721 SMC-CR1021 SMC-CR1521 SMC-CR2021 SMC-CR3021
SMC-CR0511 SMC-CR0521 SMC-CR0721 SMC-CR1021 SMC-CR1521 SMC-CR2021 SMC-CR3021 SMC-CR5021
SMC-CR0511 SMC-CR0521 SMC-CR0721 SMC-CR1021 SMC-CR1521 SMC-CR2021 SMC-CR3021 SMC-CR5021
15
M9110WS
4" Submersible pumps
S Series
ORDERING INFORMATION
Motor
GPM
Type
2-Wire
25 3-Wire
2-Wire
40 3-Wire
75
3-Wire
HP 1/2 3/4 1 1-1/2 1/2 3/4 1 1-1/2 2 3 5 7-1/2 1 1-1/2 1 1-1/2 2 3 5 7-1/2 10 2 3 5 7-1/2 10
Assembled Pump
Volt Catalog Number 2S52-25-P4 2S72-25-P4
230 2S102-25-P4 2S152-25-P4 3S52-25-P4 3S72-25-P4 3S102-25-P4 3S152-25-P4
230
Length Inches*
18-7/8 20-3/4 23-7/8
29 18-1/8 20-3/4 23-7/8
27
2S102-40-P4 230
2S152-40-P4 3S102-40-P4 3S152-40-P4
230
24-7/8 31-3/4 24-7/8 29-3/4
*Length and weight are approximate.
DISCHARGESIZES: · The 5, 10 and 16 gallon SST pumps have 1-1/4" discharge · The 25, 40 and 75 gallon SST pumps have 2" discharge
Weight Pounds*
25 27 31 39 25 27 31 39
32 42 32 42
Pump End
Catalog Number S5-25 S7-25 S10-25 S15-25 S5-25 S7-25 S10-25 S15-25 S20-25 S30-25 S50-25 S75-25 S10-40 S15-40 S10-40 S15-40 S20-40 S30-40 S50-40 S75-40 S100-40 S20-75 S30-75 S50-75 S75-75 S100-75
Length Inches* 8-5/8 10-1/4 11-7/8 13-1/2 8-5/8 10-1/4 11-7/8 13-1/2 15-1/4 18-1/2 27-5/8 42-3/4 12-7/8 16-1/4 12-7/8 16-1/4 19-1/2 22-7/8 32-3/4 49-3/8 57-5/8 19-1/4 28-7/8 43-1/4 62-1/2 86-1/2
Pentek® Motor
Catalog Number P42B0005A2 P42B0007A2 P42B0010A2 P42B0015A2 P43B0005A2 P43B0007A2 P43B0010A2 P43B0015A2 P43B0020A2 P43B0030A2 P43B0050A2 P43B0075A3 P42B0010A2 P42B0015A2 P43B0010A2 P43B0015A2 P43B0020A2 P43B0030A2 P43B0050A2 P43B0075A3 P43B0100A4 P43B0020A2 P43B0030A2 P43B0050A2 P43B0075A3 P43B0100A4
Control Box Catalog Number
SMC-CR0521 SMC-CR0721 SMC-CR1021 SMC-CR1521 SMC-CR2021 SMC-CR3021 SMC-CR5021
SMC-CR1021 SMC-CR1521 SMC-CR2021 SMC-CR3021 SMC-CR5021
SMC-CR2021 SMC-CR3021 SMC-CR5021
16
M9110WS
Total head in meters
4" Submersible pumps
S Series
Total head in feet
PUMP PERFORMANCE 5 GPM
Capacity liters per minute
0
5
10 15 20 25 30 35
1400
3 HP
400
1200
1000
2 HP
300
800
1-1/2 HP 600 1 HP
200
3/4 HP
400 1/2 HP
100
200
0
0
2
4
6
8
10
Capacity gallons per minute
PUMP PERFORMANCE 16 GPM
0 1200
Capacity liters per minute
20
40
60
80
5 HP
1000
800
3 HP
600
2 HP
1-1/2 HP
400
1 HP 3/4 HP 200 1/2 HP
0
5
10
15
20
Capacity gallons per minute
350 300 250 200 150 100 50 0 25
Total head in meters Total head in feet
Total head in meters Total head in feet
PUMP PERFORMANCE 10 GPM
0 1400 1200 1000
Capacity liters per minute
10
20
30
40
5 HP
3 HP
800
2 HP
600 1-1/2 HP
1 HP 400 3/4 HP
1/2 HP
200
50 400 300 200 100
0
0
2
4
6
8
10
12
14
Capacity gallons per minute
PUMP PERFORMANCE 25 GPM
Capacity liters per minute
0
25 50 75 100 125 150 175
1200 350
1000
7-1/2 HP
300
800
5 HP
600
3 HP
400
2 HP
1-1/2 HP
1 HP
200
3/4 HP
1/2 HP
0
10
20
30
40
Capacity gallons per minute
250 200 150 100 50 0 50
Total head in feet
Total head in meters
17
M9110WS
Total head in feet Total head in meters
Total head in feet Total head in meters
4" Submersible pumps
S Series
PUMP PERFORMANCE 40 GPM
0 1000
Capacity liters per minute
50
100
150
200
300
10 HP
800
7-1/2 HP
600
5 HP
400
3 HP
200
2 HP
1-1/2 HP
1 HP
0
10
20
30
40
50
Capacity gallons per minute
250 200 150 100 50 0 60
OUTLINE DIMENSIONS
PUMP PERFORMANCE 75 GPM
Capacity liters per minute
0
50 100 150 200 250 300 350
600 175
10 HP
500
150
400
7-1/2 HP
125
100
300
5 HP
75
200
3 HP
50
100 2 HP
25
0
0
20
40
60
80
100
Capacity gallons per minute
Discharge
3-7/8"
Length
Suction Overall
Staging
DISCHARGE
GPM NPT
5 1-1/4
10 1-1/4
16 1-1/4
25
2
40
2
75
2
Motor 18
Dimensions (in inches) are for estimating purposes only.
M9110WS
4" Submersible pumps
S Series
PUMP PERFORMANCE
2-Wire HP Cat. No.
3-Wire Cat. No.
Pump Tank End Pres. Only 0
Pumping Depth in Feet 20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950
5 GALLONS PERMINUTE
1/2 2S52-5-P4 3S525-P4
S5-5
6.5 6.0 5.8 5.3 4.8 4.5 3.8 3.0
3/4 2S72-5-P4 3S72-5-P4 1 2S102-5-P4 3S102-5-P4
S7-5 30
S10-5
6.5 6.3 6.0 5.8 4.8 4.0 3.0 6.5 5.8 5.3 4.5 3.8 3.0
1-1/2 2S152-5-P4 3S152-5-P4
S15-5
6.3 5.8 5.3 4.5 4.0 3.3
1/2 2S52-5-P4 3S525-P4
S5-5
6.5 6.0 5.8 5.3 4.8 4.5 3.8 3.0
3/4 2S72-5-P4 3S72-5-P4 1 2S102-5-P4 3S102-5-P4
S7-5 40
S10-5
6.5 6.3 6.0 5.8 5.3 4.5 3.5 6.5 6.2 5.5 4.9 4.3 3.3
1-1/2 2S152-5-P4 3S152-5-P4 10 GALLONS PERMINUTE 1/2 2S52-10-P4 3S52-10-P4
S15-5 S5-10
13.0 12.0 11.0 9.5 8.0 6.5
6.5 6.0 5.5 5.0 4.4 3.6 3.0
3/4 2S72-10-P4 3S72-10-P4
S7-10
30
1 2S102-10-P4 3S102-10-P4
S10-10
13.2 12.3 11.5 11.0 10.7 9.5 8.5 6.7 13.3 12.6 12.0 11.4 10.3 8.0 6.0
1-1/2 2S152-10-P4 3S152-10-P4
S15-10
12.6 12.1 11.5 10.5 8.8 7.0
1/2 2S52-10-P4 3S52-10-P4
S5-10
13.0 12.1 11.1 9.5 8.0 6.0
3/4 2S72-10-P4 3S72-10-P4
S7-10
40
1 2S102-10-P4 3S102-10-P4
S10-10
13.0 12.0 11.2 10.6 9.5 8.5 7.0 12.7 12.0 11.1 10.3 9.3 7.2
1-1/2 2S152-10-P4 3S152-10-P4 16 GALLONS PERMINUTE 1/2 2S52-16-P4 3S52-16-P4
S15-10 S5-16 20.5 18.5 16.5 12.0
13.0 12.2 11.2 9.8 8.3 6.2
3/4 2S72-16-P4 3S72-16-P4
S7-16
30
1 2S102-16-P4 3S102-16-P4
S10-16
20.0 18.0 15.0 11.5 20.5 18.5 17.0 15.5 13.5 11.0
1-1/2 2S152-16-P4 3S152-16-P4
S15-16
20.0 18.8 17.0 14.0
1/2 2S52-16-P4 3S52-16-P4
S5-16 18.5 16.0 12.0
3/4 2S72-16-P4 3S72-16-P4
S7-16
40
1 2S102-16-P4 3S102-16-P4
S10-16
20.0 18.0 15.5 12.0 20.5 19.0 17.0 16.0 14.0 11.0
1-1/2 2S152-16-P4 3S152-16-P4
S15-16
20.0 19.0 17.5 16.3 12.0
19
M9110WS
4" Submersible pumps
S Series
PUMP PERFORMANCE
2-Wire HP Cat. No.
3-Wire Cat. No.
Pump
Pumping Depth in Feet
Tank End Pres. Only 0 20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900
25 GALLONS PERMINUTE
1/2 2S52-25-P4 3S52-25-P4
S5-25 15.0
3/4 2S72-25-P4 3S72-25-P4
S7-25 28.0 24.0 17.0
30
1 2S102-25-P4 3S102-25-P4
S10-25
33.0 30.0 27.0 22.5 17.0
1-1/2 2S152-25-P4 3S152-25-P4
S15-25
32.0 30.0 28.0 23.0 20.0 14.5
1/2 2S52-25-P4 3S52-25-P4
S5-25
3/4 2S72-25-P4 3S72-25-P4
S7-25 24.0 18.0
40
1 2S102-25-P4 3S102-25-P4
S10-25
30.5 27.5 23.0 16.0
1-1/2 2S152-25-P4 3S152-25-P4 40 GALLONS PERMINUTE 1 2S102-40-P4 3S102-40-P4 1-1/2 2S152-40-P4 3S152-40-P4
S15-25
30.5 28.0 24.5 19.5 14.0
S10-40 30.0
30
S15-40
48.0 36.0 17.0
1 2S102-40-P4 3S102-40-P4
S10-40
40
1-1/2 2S152-40-P4 3S152-40-P4
S15-40 47.0 35.0 16.0
20
M9110WS
4" Submersible pumps
The Ranger
The Ranger Series 4" high-flow submersible pumps are perfect for applications requiring a large volume of water. Stainless steel components and high-density composite resin impellers provide exceptional resistance to corrosion in harsh water conditions. The high-torque motor and superior pump hydraulics are carefully matched to handle virtually any job.
APPLICATIONS
n Water systems... irrigation, industrial, commercial, multiple housing and farm clean water use
SPECIFICATIONS
Shell 300 Series Stainless Steel
Discharge 300 Series Stainless Steel
Discharge Bearing Buna-N
Impellers Engineered Composite
Diffusers Engineered Composite
Suction Caps Engineered Composite
Shaft and Coupling 300 Series Stainless Steel
Intake 300 Series Stainless Steel
Intake Screen 300 Series Stainless Steel
Cable Guard 300 Series Stainless Steel
Fasteners 300 Series Stainless Steel
FEATURES
Turn Up the Volume High-flow capacities to 100 GPM make the Ranger 4" sub the easy choice for the really big jobs. More Stainless Steel Shell, discharge and suction bowl, shaft and coupling, lead guard and suction screen. Staged for Toughness Specially designed, high-density thermo-plastic impellers resist the corrosive wear from harsh water conditions. High-powered Performance Features a high-torque, heavy-duty motor for the most demanding applications.
21
M9111WS
4" Submersible pumps
The Ranger
ORDERING INFORMATION PUMP
Assembled Pump
Catalog
Length
Weight
GPM
HP
Stages Number
Inches* Pounds*
1
7
SS10-25
18
12
1-1/2
9
SS15-25
21
14
2
11
SS20-25
24
15
25
3
15
SS30-25
30
19
5
25
SS50-25
48
27
7-1/2
37
SS75-25
67
55
1
4
SS10-35
15
10
1-1/2
6
SS15-35
18
12
2
8
SS20-35
22
14
35
3
11
SS30-35
28
17
5
18
SS50-35
43
24
7-1/2
28
SS75-35
62
52
10
37
SS100-35
75
63
1-1/2
6
SS15-50
21
14
2
7
SS20-50
23
15
3
10
SS30-50
31
19
50
5
16
SS50-50
48
27
7-1/2
25
SS75-50
70
59
10
32
SS100-50
84
68
2
6
SS20-80
29
16
3
9
SS30-80
39
20
80
5
14
SS50-80
59
45
7-1/2
22
SS75-80
66
59
10
27
SS100-80
100
69
OUTLINE DIMENSIONS
Pump Length
MOTOR / CONTROL BOX
No. of HP Wires Volts PH
2 1
3 2 1-1/2 3
23
33
53
7-1/2 3 10 3
230 1 230 1 460 3 230 1 230 1 230 3 460 3 230 1 230 3 460 3 230 1 230 3 460 3 230 1 230 3 460 3 230 3 460 3 460 3
Pentek®Motor
Catalog Number
Length
Pentek
Weight Control Box
Inches* Pounds* Catalog Number
P42B0010A2 12 P43B0010A2 12 P43B0010A4 12 P42B0015A2 15 P43B0015A2 14 P43B0015A3 13 P43B0015A4 12 P43B0020A2 15 P43B0020A3 14 P43B0020A4 14 P43B0030A2 24 P43B0030A3 21 P43B0030A4 15 P43B0050A2 30 P43B0050A3 24 P43B0050A4 22 P43B0075A3 30 P43B0075A4 28 P43B0100A4 31
22 22 SMC-CR1021 23 30 27 SMC-CR1521 23 23 29 SMC-CR2021 27 27 49 SMC-CR3021 40 32 66 SMC-CR5021 50 55 66 70 78
*Length and weight are approximate.
P3u.7m8"p Width
22
M9111WS
Total head in meters
4" Submersible pumps
The Ranger
Total head in feet
PUMP PERFORMANCE 25 GPM
Capacity liters per minute
0
25 50 75 100 125 150 175
1200 350
1000
7-1/2 HP
300
800
5 HP
600
3 HP
400
2 HP 1-1/2 HP
200
1 HP
0
10
20
30
40
Capacity gallons per minute
250 200 150 100 50 0 50
PUMP PERFORMANCE 50 GPM
Capacity liters per minute
0
50
100
150
200
250
1000
10 HP
800
7-1/2 HP
600
5 HP
400
3 HP 2 HP
200
1-1/2 HP
300 300 250 200 150 100 50
0
0
10 20 30 40 50 60 70 80
Capacity gallons per minute
Total head in meters Total head in feet
Total head in meters Total head in feet
PUMP PERFORMANCE 35 GPM
Capacity liters per minute
0
50
100
150
200
1200
10 HP
350
1000
300
800
7-1/2 HP
250
200 600
5 HP
150
400
3 HP
100
2 HP
200
1-1/2 HP
1 HP
50
0
0
10
20
30
40
50
60
Capacity gallons per minute
PUMP PERFORMANCE 80 GPM
0 700 600 500 400 300
Capacity liters per minute
50 100 150 200 250 300 350 400 450
200
10 HP
7-1/2 HP
150
5 HP
100
200
3 HP
2 HP
50
100
0
0
20
40
60
80
100
120
Capacity gallons per minute
Total head in feet
Total head in meters
23
M9111WS
4" Submersible pumps
The Ranger
PUMP PERFORMANCE
HP
Catalog
Tank
Pumping Depth in Feet
Number Pressure 0 20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850
25 GALLONS PERMINUTE
1 SS10-25
20/40 30/50
35 31 27 22 18 11 30 28 22 17 12
1-1/2 SS15-25
20/40 30/50
33 30 27 23 20 15 36 33 30 27 23 20 15
2 SS20-25
20/40 30/50
36 33 31 28 25 21 17 36 33 31 27 24 20 16
3 SS30-25
20/40 30/50
33 30 25 18 36 34 32 30 28 22 15
5 SS50-25
20/40 30/50
37 34 31 28 25 22 18 13 36 33 30 27 24 21 16
7-1/2 SS75-25
20/40 30/50
34 32 30 28 26 23 19 16 37 36 34 32 29 27 24 22 18 15
35 GALLONS PERMINUTE
1 SS10-35
20/40 30/50
1-1/2 SS15-35
20/40 30/50
2 SS20-35
20/40 30/50
3 SS30-35
20/40 30/50
5 SS50-35
20/40 30/50
7-1/2 SS75-35
20/40 30/50
10
SS100-35
20/40 30/50
37 25 25
49 43 35 28 42 34 26 15
50 46 41 35 27 50 46 40 33 26 16
49 46 42 38 33 27 49 45 42 37 33 26 21 15
49 47 45 39 32 23 49 47 45 43 36 28 18
50 47 44 40 36 32 27 49 46 43 38 34 30 24 16
51 49 48 46 43 40 38 35 32 29 25 49 48 47 45 42 39 37 34 30 27 23
50 GALLONS PERMINUTE
1-1/2 SS15-50
20/40 30/50
65 56 46 37 55 45 34 20
2 SS20-50
20/40 30/50
63 56 47 40 30 64 55 47 40 29
3 SS30-50
20/40 30/50
64 60 55 50 44 36 64 60 55 49 44 35 29
5 SS50-50
20/40 30/50
67 64 61 57 54 51 41 30 66 64 60 57 54 50 46 36 23
7-1/2 SS75-50
20/40 30/50
67 65 60 55 49 43 35 67 65 63 58 53 46 40 32
10
SS100-50
20/40 30/50
68 65 61 58 53 48 44 39 33 67 63 59 56 51 46 42 37 30
80 GALLONS PERMINUTE
2 SS20-80
20/40 30/50
75 56 40 58 40
3 SS30-80
20/40 30/50
93 81 72 60 50 81 71 60 48 37
5 SS50-80
20/40 30/50
94 87 80 72 63 57 49 40 100 94 88 80 72 62 58 50 40
7-1/2 SS75-80
20/40 30/50
100 96 91 87 82 77 72 60 45 100 96 90 87 82 78 72 67 52 39
10
SS100-80
20/40 30/50
97 95 93 89 84 72 68 58 95 93 90 86 81 70 65 55
24
M9111WS
Submersible motors and motor controls
PENTEK® XE Series 4" Submersible Motors
Built with the latest design, manufacturing and testing technology, the Pentek XE Series 4" submersible high-thrust motors feature laserwelded 304L stainless steel construction, higher thrust capacities and higher efficiencies. The Pentek XE Series submersible motors incorporate "encapsulated, epoxy stator design," and professional-grade Class F insulation provides longer life in harsh environments. Each motor is 100% factory pressure and run tested to support our quality standards.
APPLICATIONS
n Water systems... for residential, industrial, commercial, multiple housing and farm clean water use.
SPECIFICATIONS
End Bell 304 Stainless Steel
Shell 304 Stainless Steel
Motor Shaft 17-4 Precipitation Hardened Stainless Steel
Insulation Class F, 311°F (155°C)
Max. Water Temp 86°F (30°C)
Fasteners 304 Stainless Steel
Sand Boot Nitrile
Cable Field-serviceable, Controlled Compression Design, UL and CSA Approved
Cable Length 48"
Diaphragm EPDM
Thrust Bearings Kingsbury-type, pivot shoe, carbon graphite mating ring
Thrust Load Capacity 700 lbs.
FEATURES
700# Rated Kingsbury Thrust Bearing Design Large high-performance bearings are standard on all HPs allowing for higher thrust loads, providing many years of trouble-free service under severe-duty operation.
2-Wire Permanent Split Capacitor Design insures quiet operation and improved operating efficiency.
3-Wire Motors Operate with Pentek SMC and other single-phase motor controls.
All Stainless Steel Exterior
Professional-Grade Class F-Compliant Motor Insulation Allows for longer service life.
UL, CSA Approved and 100% Factory Pressure and Run Tested
Equipped withSurge Arrestor
Automatic Thermal Protection on 1/2 1 HP Models
LPIRGOHTTENCITNIGON
25
M9112WS
Submersible motors and motor controls
PENTEK® XE Series 4" Submersible Motors
ORDERING INFORMATION
Rating
Service HP kW Volts Hz Factor
Catalog Number
Full Load Amps
PSC 2 Wire 1/2 0.37 3/4 0.55 1 0.75 1-1/2 1.1
CSIR 3 Wire 1/2 0.37 3/4 0.55 1 0.75 CSCR 3 Wire 1/2 0.37 3/4 0.55 1 0.75 1-1/2 1.1 2 1.5 3 2.2 5 3.7 3 Phase
HP kW 1/2 0.37
3/4 0.55
1 0.75
1-1/2 1.1
2 1.5
3 2.2
5 3.7
7-1/2 5.6
10 7.5
115 230 230 60 230 230
115
230 230
60
230
230 60
Rating
Volts Hz
200
230 60
460
200
230 60
460
200
230 60
460
200
230 460
60
575
200
230 460
60
575
200
230 460
60
575
200
230 460
60
575
200
230 460
60
575
460 60
1.6 1.6 1.5 1.4 1.3
1.6 1.6 1.5 1.4
1.6 1.5 1.4 1.3 1.25 1.15 1.15
Service Factor
1.6
1.5
1.4
1.3
1.25
1.15
1.15
1.15
1.15
P42B0005A1 P42B0005A2 P42B0007A2 P42B0010A2 P42B0015A2
P43B0005A1 P43B0005A2 P43B0007A2 P43B0010A2
P43B0005A2 P43B0007A2 P43B0010A2 P43B0015A2 P43B0020A2 P43B0030A2 P43B0050A2
Catalog Number P43B0005A8 P43B0005A3 P43B0005A4 P43B0007A8 P43B0007A3 P43B0007A4 P43B0010A8 P43B0010A3 P43B0010A4 P43B0015A8 P43B0015A3 P43B0015A4 P43B0015A5 P43B0020A8 P43B0020A3 P43B0020A4 P43B0020A5 P43B0030A8 P43B0030A3 P43B0030A4 P43B0030A5 P43B0050A8 P43B0050A3 P43B0050A4 P43B0050A5 P43B0075A8 P43B0075A3 P43B0075A4 P43B0075A5 P43B0100A4
7.4 3.7 5.0 7.9 9.2
11.0 5.5 7.2 8.4
4.1 5.1 6.1 9.7 9.9 14.3 24
Full Load Amps 2.9 2.4 1.3 3.8 3.3 1.7 4.6 4.0 2.2 6.3 5.2 2.8
2 7.5 6.5 3.3 2.7 10.9 9.2 4.8 3.7 18.3 15.7 7.6 7.0 27.0 24.0 12.2 9.1 15.6
Max. Load (SF Load)
Amps
9.5 4.7 6.4 9.1 11.0
12.6 6.3 8.3 9.7
4.9 6.3 7.2 11.1 12.2 16.5 27
Max. Load (SF Load)
Amps 3.4 2.9 1.5 4.5 3.9 2.0 5.5 4.7 2.5 7.2 6.1 3.2 2.4 8.8 7.6 3.8 3.3 12.0 10.1 5.3 4.1 20.2 17.5 8.5 7.6 30.0 26.4 13.5 10.0 17.2
Locked Rotor Amps
Winding
Main
Start
Resistance Resistance
Thrust Rating
Length
Weight
In. mm Lb. Kg
36.4
1.3-1.8
19.5
4.5-5.2
24.8
3.0-4.8
21.7
4.2-5.2
42.0
1.9-2.3
11.0 279 19.2 8.7
11.0 279 19.2 8.7
700
12.4 314 22.7 10.3
13.3 337 24.5 11.1
14.9 378 28.9 13.1
49.6
0.9-1.6
5.7-7.0
10.0 253 18.9 8.6
22.3 32.0
4.2-4.9 2.6-3.6
17.4-18.7 11.8-13.0
700
9.7 246 18.1 8.2 10.8 275 21.4 9.7
41.2
2.2-3.2
11.3-12.3
11.7 297 23.1 10.5
22.3 32.0 41.2 47.8 49.4 76.4 101.0
4.2-4.9 2.6-3.6 2.2-3.2 1.6-2.3 1.6-2.2 1.1-1.4 0.62-0.76
17.4-18.7 11.8-13.0 11.3-12.3 7.9-8.7 10.8-12.0 2.0-2.5 1.36-1.66
9.7 246 18.1 8.2
700
10.8 275 21.4 9.7 11.7 297 23.1 10.5
13.6 345 27.4 12.4
900
15.1 383 31.0 14.1 18.3 466 40.0 18.1
1500 27.7 703 70.0 31.8
Line to Line Resistance Ohms
4.1-5.2 5.72-7.2 23.6-26.1 2.6-3.0 3.3-4.3 14.4-16.2 3.4-3.9 4.1-5.1 17.8-18.8 1.9-2.5 2.8-3.4 12.3-13.1 19.8-20.6 1.4-2.0 1.8-2.4 8.00-8.67 9.4-9.7 0.9-1.3 1.3-1.7 5.9-6.5 9.4-9.7 0.4-0.8 0.85-1.25 3.58-4.00 3.6-4.2 0.5-0.6 0.55-0.85 1.9-2.3 3.6-4.2 1.8-2.2
Locked Rotor Amps
22 17.3
9 32.0 27 14 29.0 26.1 13.0 40.0 32.4 16.3 11.5 51.0 44.0 23.0 21.4 71.0 58.9 30.0 21.4 113.0 93.0 48.0 55.0 165.0 140.0 87.0 55.0 110.0
Thrust Rating 700 900 1500
Length
In. mm
10.0 254 10.0 254 10.0 254 10.8 274 10.8 274 10.8 274 11.7 297 11.7 297 11.7 297 11.7 297 11.7 297 11.7 297 11.7 297 13.8 351 13.8 351 13.8 351 15.3 389 15.3 389 15.3 389 15.3 389 15.3 389 21.7 551 21.7 551 21.7 551 27.7 703 27.7 703 27.7 703 27.7 703 27.7 703 30.7 780
Weight
Lb. Kg
18.9 8.6 18.9 8.6 18.9 8.6 21.4 9.7 21.4 9.7 21.4 9.7 23.1 10.5 23.1 10.5 23.1 10.5 23.1 10.5 23.1 10.5 23.1 10.5 23.1 10.5 27.4 12.4 27.4 12.4 27.4 12.4 32 14.5 32 14.5 32 14.5 32 14.5 32 14.5 55 24.9 55 24.9 55 24.9 70 31.8 70 31.8 70 31.8 70 31.8 70 31.8 78 35.4
NOTE: Amp ratings on 3-wire motors reflect use with CSIR controls. A CSCR control is recommended for lower values.
26
M9112WS
Submersible motors and motor controls
PENTEK® XE Series 4" Submersible Motors
OUTLINE DIMENSIONS
LEADLENGTH
Catalog Number # of Wire
Type
XESERIESREPLACEMENTMOTORLEADS
P18-1485K
2 Wire
XLPE
P18-1486K
3 Wire
XLPE
P18-1651K
2 Wire
XLPE
P18-1652K
3 Wire
XLPE
Length Gauge
48"
14 Ga
48"
14 Ga
100"
14 Ga
100"
14 Ga
Dimensions (in inches) are for estimating purposes only.
27
M9112WS
Submersible motors and motor controls
Cable Selection
Two different cable sizes can be used. The example below is for reference. Depending on the installation, any number of combinations may be used, as long as the total percentage length of the two cables used does not exceed 100%. This is to ensure that adequate voltage will be supplied to the motor.
Example: 1 HP, 230 Volt, 3W, 1 PHMotor
In a replacement installation, the well already has 210 feet of buried #12 cable between the service entrance and the well head. The question is:What size cable is required in the well with a 1 HP, 230 Volt, 1 PH, 3W motor setting at 310 feet? 1. According to the table, #12 cable is large enough for the 1 HP
motor so the percent of the maximum allowable cable used by the 210-foot run is 210 ÷ 359 = 58.5%, since 359 feet is the total allowable. 2. With 58.5% of the total allowable cable already used between the service entrance and the well head, only 41.5% is left for the well. Therefore, the 310 feet needed in the well can only utilize 41.5% of the total feet allowed in the table. 3. From the table, 41.5% of the 573 feet for #10 cable equals only 238 feet, so a larger size is needed. For #8, 41.5% of 908 feet = 377 feet. As a result, #8 can be used for the 310 feet in the well.
CAUTION Use of wire size smaller than listed will void warranty.
MOTOR LEAD LENGTHS PENTEK® 2-WIRE MOTORS
60 Hz Motor Rating
60C and 75C Insulation AWG Copper Wire Size
Volts
HP
14
12
10
8
6
4
3
2
1
1/0
2/0
3/0
4/0
115
1/2
115
183
293
463
721 1150 1445 1825 2299 2902 3662 4623
5824
1/2
466
742 1183 1874 2915 4648 5843 7379 9295 11733
3/4
342
545
869 1376 2141 3413 4291 5419 6826 8617 10871
230
1
241
383
611
968 1506 2400 3018 3811 4801 6060 7646 9652
1-1/2 199
317
505
801 1246 1986 2496 3153 3972 5013 6325 7985
MOTOR LEAD LENGTHS PENTEK 3-WIRE PSC MOTORS
CSIR Control Boxes
60 Hz Motor Rating
60C and 75C Insulation AWG Copper Wire Size
Volts
HP
14
12
10
8
6
4
3
2
1
1/0
2/0
3/0
4/0
115
1/2
87
138
221
349
544
867 1090 1376 1734 2188 2761 3485
4391
1/2
348
553
883 1398 2175 3467 4359 5505 6935 8753
230
3/4
264
420
670 1061 1651 2632 3309 4178 5264 6644 8383
1
226
359
573
908 1413 2252 2831 3575 4504 5685 7173
CSCR Control Boxes
60 Hz Motor Rating
60C and 75C Insulation AWG Copper Wire Size
Volts 230
HP
14
12
10
8
6
4
3
2
1
1/0
2/0
3/0
4/0
1/2
447
711 1135 1797 2796 4458 5604 7078 8916 11254
3/4
348
553
883 1398 2175 3467 4359 5505 6935 8753 11044
1
304
484
772 1223 1903 3034 3814 4817 6068 7659 9663
1-1/2 197
314
501
793 1234 1968 2474 3124 3936 4968 6268
2
180
286
456
722 1123 1790 2251 2843 3581 4520 5703
3
133
211
337
534
830 1324 1664 2102 2648 3342 4217 5323
5
206
326
507
809 1017 1284 1618 2042 2577 3253
All lengths in feet. NOTE: Based on service factor amps, 30C ambient and 5% voltage drop.
(1) This table is based on copper wire. If aluminum wire is used it must be two sizes larger. Example: When the table calls for #12 copper wire you would use #10 aluminum wire.
(2) Cables #14 to #0000 are AWG sizes.
28
M10269WS
Submersible motors and motor controls
Cable Selection
MOTOR LEAD LENGTHS PENTEK® 3-PHASE MOTORS
60 Hz Motor Rating
60C AND 75C Insulation AWG Copper Wire Size
Volts
HP
14
12
10
8
6
4
3
2
1
1/0
2/0
3/0
0.5
657
1045 1667 2641 4109
3/4
423
674
1074 1702 2648
1
346
551
879
1392 2166 3454 4342
1.5
265
421
672
1064 1655 2638 3317
200
2
217
344
549
870
1354 2158 2714 3427 4317 5449
3
159
253
403
638
993
1583 1990 2513 3166 3996
5
94
150
239
379
590
940
1182 1493 1881 2374
2995
3781
7.5
64
101
161
255
397
633
796
1005 1266 1598
2017
2546
0.5
756
1202 1917 3037 4725 7532 9469
0.75
562
894
1426 2258 3513 5601 7041 8892
1
466
742
1183 1874 2915 4648 5843 7379
1.5
359
571
912
1444 2246 3581 4502 5685 7162 9040
230
2
288
459
732
1159 1803 2874 3613 4563 5748 7256
9155
3
217
345
551
872
1357 2163 2719 3434 4326 5460
6889
8696
5
318
503
783
1248 1569 1982 2496 3151
3976
5019
7.5
334
519
827
1040 1314 1655 2089
2635
3327
0.5
2922 4648 7414
0.75 2191 3486 5560 8806
1
1753 2789 4448 7045
1.5
1370 2179 3475 5504
460
2
1153 1835 2926 4635 7212
3
827
1315 2098 3323 5171
5
516
820
1308 2072 3224 5140
7.5
325
516
824
1305 2030 3236 4068 5138 6472
10
255
405
647
1024 1593 2540 3193 4033 5080
1.5
2283 3631 5792
2
1660 2641 4212 6671
575
3
1336 2126 3390 5370
5
721
1147 1829 2897 4507
7.5
548
871
1390 2202 3426
All lengths in feet. NOTE: Based on service factor amps, 30C ambient and 5% voltage drop.
(1) This table is based on copper wire. If aluminum wire is used it must be two sizes larger. Example: When the table calls for #12 copper wire you would use #10 aluminum wire.
(2) The portion of the total cable that is between the service entrance and a 3-phase motor starter should not exceed 25% of the total maximum length to assure reliable starter operation.
(3) Cables #14 to #0000 are AWG sizes.
4/0
4764 3207
10956 6323 4192
29
M10269WS
Submersible motors and motor controls
Submersible Motor Controls
Pentek® offers a full range of 1/2 - 15 HP models that are interchangeable with existing motor controls for Capacitor Start/Induction Run (CSIR) and Capacitor Start/Capacitor Run (CSCR) applications. Pentek is the professional choice in harsh and high temperature installations.
APPLICATIONS
n Water systems... for residential, commercial, multiple housing and farm uses, where a submersible 3-wire motor is used. A features
Enclosure: Rugged NEMA 3R enclosure Suitable for indoor/outdoor use. NEW HardBondTM Finish 5-times more corrosion-resistant. Multiple-size Electrical Knockouts
Internals: High-load Voltage Relay Heavy-duty Contacts External Access to Overload Reset CSCR Heavy-duty Terminal Connectors Suitable for up to #4 AWG wire. Industry Standard Wiring Connections Easy-to-read wiring diagrams. Agency Approvals UL 778 and CUL Recognized (60 Hz)
C B
30
M9114WS
Submersible motors and motor controls
Submersible Motor Controls
ORDERING INFORMATION
60 Hz
HP
kW
PH
Volts
Catalog Number
CSIR Capacitor Start/Induction Run
1/2
0.37
1
1/2
0.37
1
3/4
0.55
1
115
SMC-IR0511 (-6pk)*
230
SMC-IR0521 (-6pk)*
230
SMC-IR0721 (-6pk)*
1
0.75
1
230
SMC-IR1021 (-6pk)*
CSCR Capacitor Start/Capacitor Run
1/2
0.37
1
3/4
0.55
1
1
0.75
1
1-1/2
1.1
1
2
1.5
1
3
2.2
1
5
3.7
1
7-1/2
5.5
1
10
7.5
1
230
SMC-CR0521 (-6pk)*
230
SMC-CR0721 (-6pk)*
230
SMC-CR1021 (-6pk)*
230
SMC-CR1521
230
SMC-CR2021
230
SMC-CR3021
230
SMC-CR5021
230
SMC-CR7521
230
SMC-CR10021
CSCR PLUS Capacitor Start/Capacitor Run PLUS Magnetic Contactor
2
1.5
1
230
SMC-CRP2021
3
2.2
1
230
SMC-CRP3021
5
3.7
1
230
SMC-CRP5021
7-1/2
5.5
1
230
SMC-CRP7521
10
7.5
1
230
SMC-CRP10021
15
11
1
230
SMC-CRP15021
50 Hz Catalog Number
SMC5-CR0521 SMC5-CR0721 SMC5-CR1021 SMC5-CR1521 SMC5-CR2021 SMC5-CR3021 SMC5-CR5021
SMC5-CRP2021 SMC5-CRP3021 SMC5-CRP5021
Weight
Lbs
Kg
4
1.8
4
1.8
4
1.8
4
1.8
5
2.3
5
2.3
5
2.3
7
3.2
7
3.2
7
3.2
8
3.6
12
5.4
14
6.4
7
3.2
8
3.6
12
5.4
14
6.4
15
6.8
17
7.7
Enclosure Size
A A A A
A A A B B B B C C
B B C C C C
*Submersible Motor Controls are available in single and six packs. Include the suffix "-6pk" after the catalog number if 6 packs are required.
OUTLINE DIMENSIONS
10.25
1.50
6.25
7.75
5.50
5.50
SIZE A
2.70
1.20
5.50
SIZE B
1.13 1.13 1.18
Dimensions (in inches) are for estimating purposes only.
31
16.25 14.50
5.50
1.88 8.50 16.25
14.50
5.50
2.00
5.50
7.75
2.00
SIZE C
7.75
M9114WS
Submersible motors and motor controls
Single-Phase Pump Protection
Pentek® offers a full range of 1/3 - 15 HP single-phase protectors for residential, commercial, multiple housing and farm water systems applications where a 4" submersible, 2- and 3-wire motor is used and for aboveground pressure-boost applications.
APPLICATIONS Pentek offers 5 models for your application needs based on HP and Motor Type: SPP-111P, SPP-111-3RLP, SPP-231P, SPP-233P and SPP-235P.
FEATURES Protects Pumps From dry well, overcurrent (jammed impeller), flow restriction (dead head), overvoltage, undervoltage, rapid cycling.
ORDERING INFORMATION
Catalog Number Enclosure Type 1-Phase Line Voltage Load Range Frequency Operating Points
Overload (% of Cal. Point) Overvoltage Reset Point Undervoltage Reset Point Trip Delay (Overload) Trip Delay (Dry Well) Optional Trip Delay Restart Delay Time Over/Under Voltage Delay All Other Faults (Dry Well REC. Timer) Output Contact Rating (SPST) Power Consumption (max.) Weight w/o Enclosure Weight w/Enclosure Enclosure Size
115 VOLTMODELS
SPP-111P
SPP-111-3RLP
Insider
NEMA 3R
115VAC
115VAC
1/3 - 1/2 HP
1/3 - 1 HP
50 - 60Hz
50 - 60Hz
125% 132VAC 95VAC 10 sec. 2 sec. 4 sec.
125% 132VAC 95VAC 10 sec. 2 sec. 4 sec.
5 Sec. 2 - 225 min.
1 HP 5 amps 10 oz.
2.2" x 2.8"
5 Sec. 2 - 225 min.
1 HP 5 amps
1.6 lbs. 6" x 6" x 4"
SPP-231P Insider 230VAC
1/2 - 1 HP 50 - 60Hz
230 VOLTMODELS SPP-233P NEMA 3R 230VAC 1/2 - 3 HP 50 - 60Hz
SPP-235P NEMA 3R 230VAC 5 - 15 HP 50 - 60Hz
125% 265VAC 190VAC 10 sec. 2 sec. 4 sec.
125% 265VAC 190VAC 5 sec. 2 sec. 4 sec.
125% 265VAC 190VAC 5 sec. 2 sec. 4 sec.
5 Sec. 2 - 225 min. 1 HP (17 amps max.)
5 amps 10 oz.
2.2" x 2.8"
5 Sec. 2 - 225 min. 3 HP (17 amps max.)
5 amps 14 oz. 1.6 lbs. 6" x 6" x 4"
5 Sec. 2 - 225 min. 480VA @ 240VAC
5 amps 14 oz. 1.6 lbs. 6" x 6" x 4"
32
M9115WS
Submersible motors and motor controls
SPP-111P and SPP-231P Single-Phase PumpProtection
For 1/3 - 1 HP applications, the SPP-111P and SPP-231P Insider fits within 1/3 - 1 HP 115V and 230V CSIR control boxes. It's a "current monitor" designed to protect single-phase pumps. A simple adjustment allows the Insider to be calibrated to your specific pumping applications, reducing the possibility of false or nuisance tripping. Its unique microprocessor constantly monitors the incoming power for fluctuations in voltage and current. If loss of suction or other abnormality is detected, the Insider deactivates its output relay and directly disconnects the pump motor. Then it begins its user-selectable "Restart Delay/Dry Well Recovery" timer. When the timer counts zero or power is removed and reapplied, the SPP-231P Insider reactivates its output relay and turns the pump back on.
The Pentek® Informer Remote Handheld Diagnostic Tool (sold separately) communicates directly with ALL Pentek Pump Protectors and instantly displays 16 parameters including calibration points, running points and last fault.
APPLICATIONS
n Water systems... for residential, commercial, multiple housing, farm and turf irrigation uses, where a 4" submersible 3-wire motor is used.
FEATURES
Restart Delay Can be set up to 225 minutes or placed in manual reset mode.
Calibration Can be calibrated to specific pump/motor combinations and various conditions.
Infrared Communication Coupled with the Pentek Informer makes diagnostics simple.
Fits in Existing 3-wire Motor Control Boxes
SPP-231P installed
ORDERING INFORMATION
HP
Phase
Volts
1/3 - 1/2
1
115
1/3 - 1
1
230
Frequency
50 - 60Hz 50 - 60Hz
Catalog Number
SPP-111P SPP-231P
WEIGHT
LBS.
KG
1
0.45
1
0.45
Carton Size
4.4" x 4.4" x 6.8" 4.4" x 4.4" x 6.8"
33
M9116WS
Submersible motors and motor controls
SPP-111-3RLP, SPP-233P and SPP-235P PumpProtection
For 1/2 - 15 HPapplications the SPP-111-3RLP, SPP-233P and SPP-235P single-phase protectors include a unique microcontrollerbased voltage and current-sensing circuit that constantly monitors the incoming power for fluctuations including over-current and undercurrent. When an abnormality, such as loss of suction, is detected, the control deactivates its output relay and directly disconnects the pump motor. The SPP then begins its user-selectable restart delay (dry-well recovery) timer. When the timer counts to zero or power is removed and reapplied, the SPP reactivates its output relay and turns the pump back on. An infrared LED communicates directly with a handheld diagnostic tool called the Informer (sold separately see page 60). The Informer displays 15 parameters including calibration point, trip point, running points, and last fault. The SPPs are all mounted in a NEMA 3R enclosure.
APPLICATIONS n Water systems... for residential,
commercial, multiple housing and farm uses, where a 4" 2 or 3-wire submersible motor or above-ground motor is used.
SPP-233P
FEATURES
Protects Pumps from dry well overvoltage, flow restriction (dead head), undervoltage, overcurrent (jammed impeller).
ORDERINGINFORMATION
HP 1/2 - 1 1/2 - 1-1/2 1/2 - 3 5 and 7-1/2
10 15
Phase 1 1 1 1 1 1
Volts 115 230 230 230 230 230
*Current transformer included.
Frequency 50 - 60Hz 50 - 60Hz 50 - 60Hz 50 - 60Hz 50 - 60Hz 50 - 60Hz
Catalog Number
SPP-111-3RLP SPP-233P-1.5 SPP-233P SPP-235P-75* SPP-235P-100* SPP-235P-150*
WEIGHT
LBS.
KG
1.6
0.7
1.6
0.7
1.6
0.7
2
0.9
2
0.9
2
0.9
Carton Size 7.25" x 7" x 5.25" 7.25" x 7" x 5.25" 7.25" x 7" x 5.25" 7.25" x 7" x 5.25" 7.25" x 7" x 5.25" 7.25" x 7" x 5.25"
34
M9117WS
Submersible motors and motor controls
The Informer Pump Protection
APPLICATIONS
n The Pentek® Informer... a remote handheld diagnostic tool designed for use with Pentek single-phase submersible pump protectors (SPP-111P, 231P, 233P and 235P) equipped with infrared LED transmitters.
SPECIFICATIONS
n Displayed Parameters Diagnostic information received and displayed in real-time: Voltage, Current, Power, Dry Well.
n Overload Trip Points
n Calibration Voltage
n Last Fault
n Highest/Lowest Voltage Since Last Calibration
FEATURES
Infrared Receiver The Pentek Informer uses an infrared receiver to access data sent from the SPP, allowing remote troubleshooting of the system.
Infrared LED Each Pentek SPP is equipped with an infrared LED that transmits information from the device. The Informer must be aimed at the SPP as shown in the figure to the left. As soon as power is applied, the Informer begins receiving both past and present information and displays it on the LCD.
Status Light The green COMM STATUS light indicates when the Informer is receiving data from the SPP. If communication is lost, the Informer will hold the last values it received.
45° Range, 1-10'
ORDERINGINFORMATION
Catalog Number
SPP-Informer
WEIGHT
LBS.
KG
1
0.45
Carton Size 4.375" x 3.375" x 6.75"
35
M9118WS
Submersible motors and motor controls
PENTEK INTELLIDRIVETM
The Pentek Intellidrive Water Pressure Control Center is an "Intelligent Variable Frequency Drive" that directs changes in submersible pump motor speed, responding to fluctuations in household demand. It maintains constant water pressure, regardless of how many people or appliances are using water at the same time. Homeowners with water pressure problems experience weak showers, unclean dishes, dry lawns and more.
APPLICATIONS n Residential water systems, landscape
irrigation, water transfer.
Specifications Enclosure Dimensions: Width: 9.72" Height: 19" Depth: 6.93" Carton Dimensions: 10.4" width, 22.3" height, 9.4" depth Shipping Weight: 22 pounds Ambient Temperature Range: -20°C (-4°F) to 50°C (122°F) Ambient Humidity Range: 95% non-condensing Includes: Variable Frequency Drive Transducer: 1/4" thread size, 18 NPT type Transducer Cable: 10' length standard
FEATURES
3 Models Meet all Your Needs 1-HP, 2-HP & 5-HP Capabilities
2-Wire, 3-Wire & 3-Phase in same unit
3-Phase Output (60 Hz/80 Hz)**
Pump and Motoer Last Longer "Soft Start/Coast to Stop" minimizes mechanical stress.
Constant pressure eliminates frequent on/off "pressure cycling".
Advanced Control System Needed for installation, system monitoring and troubleshooting.
Easy touchpad operation.
Ground Detection Detects and displays when there is a grounding problem.
Shuts down system until problem is corrected.
60Hz operation is recommended as the industry standard. Intermittent 80Hz operation is an acceptable option. ** Ongoing 80Hz operation may reduce the life of the pump and motor.
ordering information
Model Number
PID10
PID20
PID50
Motor Type 2-WIRE* 1-PHASE 3-WIRE* 1-PHASE 3-PHASE 2-WIRE* 1-PHASE 3-WIRE* 1-PHASE 3-PHASE 2-WIRE* 1-PHASE 3-WIRE* 1-PHASE 3-PHASE
Hp Range
0.51 HP
0.51.5 HP 0.52 HP 0.51.5 HP 0.5 2 HP 0.5 5 HP
Input Voltage
190V 265V
Maximum Output Amps
9.5A 7.5A 5A 11A 13.5A 8.5A 11A 13.5A 18A
Enclosure Type
NEMA 3R outdoor
36
p8176ws
Submersible motors and motor controls
PENTEK INTELLIDRIVETM
Keyhole Mount For fast and easy installation
LCD Information Center Displays installation, status and fault information in easy-to-understand language instead of codes
Ground Detection Message Center shows if there is a grounding problem Multiple Accessory Inputs Additional inputs allow use of multiple drive accessories at the same time
Best-In-Class EMI/RFI Filter Superior noise and interference protection, including AM radio signals
Spacious Wiring Area For fast and easy installation
Programmable Input/ Output Relays Provide application flexibility
Easy-Access Conduit Openings Align with appropriate terminals for straight-in accessibility. F its 1/2", 3/4" or 1-1/4"
37
Electronic Pressure Transducer More accurate and reliable than mechanical pressure switch, with piezo resistive technology designed to resist water hammer
Temperature- Sensitive Intelligent Fan Operates when needed for quiet operation
SD Card Slot For easy software updates when provided by manufacturer
Spring Terminals For secure connections and easy installation without special tools
Removable Terminal Blocks For easy wiring of motor and power supply field replaceable
OUTLINE DIMENSIONS
9.72"
6.93"
19"
Dimensions (in inches) are for estimating purposes only.
p8176ws
Submersible motors and motor controls
PENTEK INTELLIKITTM
The Pentek Intellidrive Constant Pressure Controller automatically adjusts motor speeds to meet changes in water demand. Instantaneous feedback from an electronic pressure transducer instructs the drive to change the submersible well pump motor speed to maintain constant pressure throughout the system.
n Pre-Specified and Packaged Constant Pressure Systems for Residential Well Water
n Maintain constant water pressure for submersible well pump systems, similar to municipal water systems
Kit contains:
n Pentek® Submersible Motor
n Myers® Submersible Pump
n Pentek Intellidrive Variable Frequency Drive
I
2
3
I Pentek Submersible Motor n Built with the latest design, manufacturing and testing technology nEncapsulated stainless steel design and professional-grade insulation provide longer life in harsh environments n 100% factory pressure- and run-tested
2 Myers Submersible Pump n Submersible pumps deliver efficient and dependable performance even in rough, aggressive water n One of the few manufacturers of both pumps and pressurized water storage tanks, now sold in over 100 countries
3 Pentek Intellidrive Variable Frequency Drive n Maintains constant pressure output regardless of fluctuating demand n Extends life of pump and motor n Utilizes a smaller pressure tank for a space-saving solution
38
M10371WS
Submersible motors and motor controls
PENTEK INTELLIKITTM
ORDERING INFORMATION
60Hz NEMA 3 Kits
Order Number
Flow Series
Shut-Off Head At Rated Flow
at Max Runout
HP
TDH (ft)
TDH (ft) Flow (GPM) TDH (ft)
Pump
M5PIK10-60
5
1HP
610
M5PIK15-60
5
1.5HP
865
M8PIK10-60
8
1HP
495
M8PIK15-60
8
1.5HP
650
M8PIK20-60
8
2HP
795
M12PIK10-60
12
1HP
390
M12PIK15-60
12
1.5HP
575
M12PIK20-60
12
2HP
630
M12PIK30-60
12
3HP
890
M20PIK10-60
20
1HP
280
M20PIK15-60
20
1.5HP
375
M20PIK20-60
20
2.0HP
470
M20PIK30-60
20
3.0HP
600
M25PIK15-60
25
1.5 HP
270
M25PIK20-60
25
2.0HP
310
M25PIK30-60
25
3.0HP
445
M35PIK15-60
35
1.5HP
175
M35PIK20-60
35
2.0HP
210
M35PIK30-60
35
3.0HP
305
M50PIK15-60
50
1.5HP
170
M50PIK20-60
50
2.0HP
205
M50PIK30-60
50
3.0HP
295
495
8
200
ST10-5PLUS
670
8
295
ST15-5PLUS
375
11
240
ST10-8PLUS
495
11
315
ST15-8 PLUS
590
11
390
ST20-8 PLUS
275
15
205
ST10-12PLUS
385
15
300
ST15-12 PLUS
450
15
330
ST20-12 PLUS
610
15
460
ST30-12 PLUS
175
25
100
ST10-20PLUS
245
25
150
ST15-20 PLUS
298
25
190
ST20-20 PLUS
390
25
220
ST30-20 PLUS
170
25
105
ST15-25 PLUS
210
35
170
SS20-25
310
35
220
SS30-25
105
50
75
SS15-35
190
50
115
SS20-35
205
50
150
SS30-35
100
65
80
SS15-50
125
65
90
SS20-50
175
65
110
SS30-50
80Hz NEMA 3 Kits
M8PIK15-80
8
M8PIK20-80
8
M8PIK30-80
8
M12PIK15-80
12
M12PIK20-80
12
M12PIK30-80
12
M20PIK15-80
20
M20PIK20-80
20
M20PIK30-80
20
M25PIK20-80
25
M25PIK30-80
25
M35PIK20-80
35
M35PIK30-80
35
M50PIK30-80
50
M80PIK30-80
80
1.5HP 2HP 3HP 1.5HP 2HP 3HP 1.5HP 2.0HP 3.0HP 2.0 HP 3.0 HP 2.0HP 3.0HP 3.0HP 3.0HP
650 795 1090 575 630 890 375 470 600 318 435 210 305 295 205
495
11
315
ST7-8 PLUS
590
11
390
ST10-8 PLUS
800
11
530
ST15-8 PLUS
385
15
300
ST7-12 PLUS
450
15
330
ST10-12 PLUS
610
15
460
ST15-12 PLUS
245
25
150
ST7-20 PLUS
298
25
190
ST10-20 PLUS
390
25
220
ST15-20 PLUS
226
25
185
ST10-25 PLUS
316
25
220
ST15-25 PLUS
190
50
115
SS10-35
205
50
150
SS15-35
175
65
110
SS15-50
100
100
55
SS20-80
Note: 80Hz Kits utilize an undersized liquid end running at higher speed to match pump performance of the curve equivalent to the driving motor. Maximum life expectancy of the liquid end is obtained using 60Hz solutions.
Drive
PID10 PID20 PID10 PID20 PID20 PID10 PID20 PID20 PID50 PID10 PID20 PID20 PID50 PID20 PID20 PID50 PID20 PID20 PID50 PID20 PID20 PID50
Motor
P43B0010A3-C P43B0015A3-C P43B0010A3-C P43B0015A3-C P43B0020A3-C P43B0010A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0010A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C
PID20 PID20 PID50 PID20 PID20 PID50 PID20 PID20 PID50 PID20 PID50 PID20 PID50 PID50 PID50
P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0015A3-C P43B0020A3-C P43B0030A3-C P43B0020A3-C P43B0030A3-C P43B0020A3-C P43B0030A3-C P43B0030A3-C P43B0030A3-C
39
M10371WS
Submersible motors and motor controls
PENTEK® Pump Controllers PPC3 and PPC5
Pentek Pump Controllers provide innovative pumping solutions for maximizing pump functionality, optimizing pump system design and reducing operating energy costs. Pentek PPCs can be used on all centrifugal motor-driven pumps including close-coupled motor drive, frame mount, submersible and line shaft turbine pumps, in a wide range of applications.
APPLICATIONS n Turf irrigation, water transfer,
light commercial water systems and agricultural.
SPECIFICATIONS HP Ratings PPC3: 1 - 30; PPC5: 1/2 - 200 Voltage PPC3: 230, 460; PPC5: 230, 460, 575 Frequency 50/60 Hz Floating Choke PPC5 only Harmonic Signature PPC3: Good; PPC5: Best Number of Relays PPC3: 1; PPC5: 3 (ext. to 6 available) Digital Inputs PPC3: 5; PPC5: 6 Multiple Pump Capable PPC5 only Mod. Bus PPC5 only Enclosure Type PPC3: NEMA 1; PPC5: NEMA 1, 12
NOTE: The output current (or amps) of the PPC must be greater than or equal to the maximum rated motor current.
PPC5 (NEMA 12)
PPC5 (NEMA 1)
PPC3 (NEMA 1)
FEATURES
PPC Controller: Variable Speed Control Meets requirements of process control with constant pressure at variable flow conditions or constant flow at variable pressure conditions.
Reduced Energy Costs Calculate energy savings online using BEC2 software at www.bec2.net.
Pump Protection From loss of prime, dead head and blocked suction.
Motor Protection From ground fault, short circuit, phase loss and imbalance, overload, undervoltage and overvoltage.
System Protection (PPC5 only) From harmonics, featuring an input choke that exceeds the performance of a fixed 5% impedance line reactor.
Phase Conversion The PPC5 will convert 1-phase power into 3-phase power, allowing the use of a 3-phase motor; the PPC3 is available in both 1and 3-phase models.
Pentek Assistant: Auto-Restart Functionality Re-starts pump after power loss.
Easily Configured for Constant Flow Applications By adjusting 2 additional menu parameters.
Multiple System Setpoints or Operating Condition Includes two independent process control setpoints to allow operation under a second process.
Time Function Supports 4 daily and weekly Start/Stop/Boost times.
40
M10372WS
Submersible motors and motor controls
PENTEK® Pump Controllers
ORDERING INFORMATION
PPC3 200-240 Volt 1-Phase IN, 3-Phase Out
Output Amps
Enclosure Size Mounting
4.7
R1
WALL
6.7
R1
WALL
7.5
R2
WALL
9.8
R2
WALL
PPC3 200-240 Volt 3-Phase IN, 3-Phase Out
4.7
R1
WALL
6.7
R1
WALL
7.5
R1
WALL
9.8
R2
WALL
17.6
R2
WALL
24.4
R3
WALL
31.0
R4
WALL
46.2
R4
WALL
PPC3 380-480 Volt 3-Phase IN, 3-Phase Out
2.4
R1
WALL
3.3
R1
WALL
4.1
R1
WALL
5.6
R1
WALL
8.8
R1
WALL
12.5
R3
WALL
15.6
R3
WALL
23.1
R3
WALL
31.0
R4
WALL
38.0
R4
WALL
44.0
R4
WALL
Model Number NEMA 1
PPC3-1-4A7-1 PPC3-1-6A7-1 PPC3-1-7A5-1 PPC3-1-9A8-1
PPC3-2-4A7-1 PPC3-2-6A7-1 PPC3-2-7A5-1 PPC3-2-9A8-1 PPC3-2-17A6-1 PPC3-2-24A4-1 PPC3-2-31A0-1 PPC3-2-46A2-1
PPC3-4-2A4-1 PPC3-4-3A3-1 PPC3-4-4A1-1 PPC3-4-5A6-1 PPC3-4-8A8-1 PPC3-4-12A5-1 PPC3-4-15A6-1 PPC3-4-23A1-1 PPC3-4-31A0-1 PPC3-4-38A0-1 PPC3-4-44A0-1
NOTE: The output current (or amps) of the PPC must be greater than or equal to the maximum rated motor current.
*Specifications are based on a 3-phase supply voltage, 208 volt or 230 volt. For operation on 1-phase input power, de-rate the drive output current by 50%. Drive output is always 3-phase voltage.
ORDERING INFORMATION
PPC5 208-240 Volt 3-Phase IN, 3-Phase Out*
Output Amps
4.6 6.6 7.5 11.8 16.7 24.2 30.8 46.2 59.4 74.8 88 114 143 178 221 248
Enclosure Size R1 R1 R1 R1 R1 R2 R2 R3 R3 R4 R4 R4 R6 R6 R6 R6
Mounting
WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL
Model Number NEMA 1
PPC5-2-4A6-1 PPC5-2-6A6-1 PPC5-2-7A5-1 PPC5-2-11A-1 PPC5-2-16A-1 PPC5-2-24A-1 PPC5-2-30A-1 PPC5-2-46A-1 PPC5-2-59A-1 PPC5-2-74A-1 PPC5-2-88A-1 PPC5-2-114A-1 PPC5-2-143A-1 PPC5-2-178A-1 PPC5-2-221A-1 PPC5-2-248A-1
PPC5 400-480 Volt 3-Phase IN, 3-Phase Out
3.3
R1
4.1
R1
6.9
R1
8.8
R1
11.9
R1
15.4
R2
23
R2
31
R3
38
R3
44
R4
59
R4
72
R4
77
R5
96
R5
124
R6
157
R6
180
R6
196
R7
245
R7
WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL WALL Wall Wall Wall Floor Floor
PPC5-4-3A3-1 PPC5-4-4A1-1 PPC5-4-6A9-1 PPC5-4-8A8-1 PPC5-4-11A-1 PPC5-4-15A-1 PPC5-4-23A-1 PPC5-4-31A-1 PPC5-4-38A-1 PPC5-4-44A-1 PPC5-4-59A-1 PPC5-4-72A-1 PPC5-4-77A-1 PPC5-4-96A-1 PPC5-4-124A-1 PPC5-4-157A-1 PPC5-4-180A-1 PPC5-4-196A-1 PPC5-4-245A-1
PPC5 500-600 Volt 3-Phase IN, 3-Phase Out
2.7
R1
WALL
PPC5-5-2A7-1
3.9
R1
WALL
PPC5-5-3A9-1
6.1
R1
WALL
PPC5-5-6A1-1
9
R1
WALL
PPC5-5-9A0-1
11
R1
WALL
PPC5-5-11A-1
17
R2
WALL
PPC5-5-17A-1
22
R2
WALL
PPC5-5-22A-1
27
R3
WALL
PPC5-5-27A-1
32
R3
WALL
PPC5-5-32A-1
41
R4
WALL
PPC5-5-41A-1
52
R4
WALL
PPC5-5-52A-1
62
R4
WALL
PPC5-5-62A-1
77
R5
WALL
PPC5-5-77A-1
99
R6
WALL
PPC5-5-99A-1
Model Number NEMA 12
PPC5-2-4A6-12 PPC5-2-6A6-12 PPC5-2-7A5-12 PPC5-2-11A-12 PPC5-2-16A-12 PPC5-2-24A-12 PPC5-2-30A-12 PPC5-2-46A-12 PPC5-2-59A-12 PPC5-2-74A-12 PPC5-2-88A-12 PPC5-2-114A-12
-- -- -- --
PPC5-4-3A3-12 PPC5-4-4A1-12 PPC5-4-6A9-12 PPC5-4-8A8-12 PPC5-4-11A-12 PPC5-4-15A-12 PPC5-4-23A-12 PPC5-4-31A-12 PPC5-4-38A-12 PPC5-4-44A-12 PPC5-4-59A-12 PPC5-4-72A-12 PPC5-4-77A-12 PPC5-4-96A-12
-- -- -- -- --
PPC5-5-2A7-12 PPC5-5-3A9-12 PPC5-5-6A1-12 PPC5-5-9A0-12 PPC5-5-11A-12 PPC5-5-17A-12 PPC5-5-22A-12 PPC5-5-27A-12 PPC5-5-32A-12 PPC5-5-41A-12 PPC5-5-52A-12 PPC5-5-62A-12 PPC5-5-77A-12 PPC5-5-99A-12
41
M10372WS
Submersible motors and motor controls
6" Hitachi® Submersible Motor
Hitachi Motors are designed for long service life and years of dependable operation. Innovative design and robust characteristics make this the perfect motor for your pumping applications. Combined with exceptional insulation and a patented epoxy fill resin, these motors exceed NEMA requirements for high water temperature by 18°F (-7.7°C). Designed with internal lubrication and cooling blend of water, antifreeze, and an antirust mixture, Hitachi submersible motors are unique in providing the industry with innovative and robust design features that will extend the serviceable life of your installation.
APPLICATIONS
n High-thrust water well applications.
SPECIFICATIONS
Motor Sleeve Stainless steel construction
Castings Baked epoxycoated gray iron
Fasteners Stainless steel
Shaft NEMA splined stainless steel
Flange NEMA standard type
Rotor Double epoxy-coated
Thrust Bearings Kingsburytype 420 stainless steel
Mechanical Seal Nitrile rubber (NBR), grease packed
Diaphragm Nitrile rubber
Sand Cap Polyurethane
Sand Slinger Stainless steel
Lead Wire (or Cable) Doubleinsulated, heat and water-resistant, 167°F/75°C, 600V
FEATURES
Higher Efficiencies and Lower Current Consumption For reduced energy costs. Corrosion-Resistant Design For long life. High-Capacity Kingsbury-type Bearings For dependable performance. Low-Profile NEMA Design For ease of installation. Replaceable Plug-in Motor Lead For ease of maintenance. Dual Voltage Type For application versatility (5 HP 30 HP 3-Phase Motors).
VFD-Compatible
Hitachi Control Box Type 1 NEMA
Enclosure In-Panel Circuit
Breaker Magnetic Contactor Terminal Blocks for External Controls UL Recognized
Hitachi® is a registered trademark of Hitachi Industrial Equipment Systems Co., Ltd.
42
M10373WS
Submersible motors and motor controls
6" Hitachi® Submersible Motor
ORDERING INFORMATION
Hp Kw Volts Ph 6" Diameter 60 Hz 5 3.7 200 3
5 3.7 230 1
5 3.7 230 3 5 3.7 460 3 7.5 5.5 200 3
7.5 5.5 230 1
7.5 5.5 230 3 7.5 5.5 460 3 10 7.5 200 3
10 7.5 230 1
10 7.5 230 3 10 7.5 460 3 15 11 200 3
15 11 230 1
15 11 230 3 15 11 460 3 20 15 200 3 20 15 230 3 20 15 460 3 25 18.5 200 3 25 18.5 230 3 25 18.5 460 3 30 22 200 3 30 22 230 3 30 22 460 3 40 30 460 3 8" Diameter 60 Hz 50 37 460 3 60 45 460 3
Service Factor
Catalog Number
Rated Service
Winding
Input Factor Input Resistance
Amps Amps
(ohms)
1.15
6HIT2-5-8 17.5
1.15
6HIT2-5-1
24
1.15
6HIT2-5-2
15
1.15
6HIT2-5-4
7.5
1.15
6HIT2-7-8 25.4
1.15
6HIT2-7-1
36
1.15
6HIT2-7-2
22
1.15
6HIT2-7-4
11
1.15
6HIT2-10-8 33.3
1.15
6HIT2-10-1 50
1.15
6HIT2-10-2 29
1.15
6HIT2-10-4 14.5
1.15
6HIT2-15-8 47.4
1.15
6HIT2-15-1 72
1.15
6HIT2-15-2 42
1.15
6HIT2-15-4 21
1.15
6HIT2-20-8 61.2
1.15
6HIT2-20-2 54
1.15
6HIT2-20-4 27
1.15
6HIT2-25-8 77.3
1.15
6HIT2-25-2 68
1.15
6HIT2-25-4 34
1.15
6HIT2-30-8 91.8
1.15
6HIT2-30-2 82
1.15
6HIT2-30-4 41
1.15
6HIT2-40-4 56
1.15 86HIT2-50-4* 65 1.15 86HIT2-60-4* 80
19.5
R-Y, B-Y, R-B,
27.5
2.172, 0.512,
2.627
17
0.806
8.5
3.05
28.5
R-Y, B-Y, R-B,
41
1.401, 0.400,
1.774
26
0.651
13
2.43
37.2
R-Y, B-Y, R-B,
58
1.052, 0.316,
1.310
33
0.448
16.5
1.619
53.5
R-Y, B-Y, R-B,
85
0.678, 0.230,
0.850
46
0.312
23
1.074
69.5
60
0.258
30
0.861
87.5
76
0.21
38
0.666
104
94
0.166
47
0.554
61
0.358
73
0.331
90
0.278
Thrust Capacity
Length (L)
In. mm
Diameter (D)
In. mm
Weight Lbs. Kg
3,500
3,500
3,500 3,500 3,500
3,500
3,500 3,500 3,500
3,500
3,500 3,500 3,500
3,500
3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 3,500 5,000
5,000 5,000
22.95" 582.9 5.5" 139.7 95 43.0
26.97" 685.0 5.5" 139.7 110 49.9
22.95" 582.9 5.5" 139.7 95 43.0 22.95" 582.9 5.5" 139.7 95 43.0 24.80" 629.9 5.5" 139.7 99 43.0
29.92" 760.0 5.5" 139.7 128 58.1
24.80" 629.9 5.5" 139.7 99 43.0 24.80" 629.9 5.5" 139.7 99 43.0 26.97" 685.0 5.5" 139.7 110 49.9
29.92" 760.0 5.5" 139.7 128 58.1
26.97" 685.0 5.5" 139.7 110 49.9 26.97" 685.0 5.5" 139.7 110 49.9 29.92" 760.0 5.5" 139.7 128 58.1
33.46" 849.9 5.5" 139.7 148 67.1
29.92" 760.0 5.5" 139.7 128 58.1 29.92" 760.0 5.5" 139.7 128 58.1 31.5" 800.1 5.5" 139.7 137 62.1 31.5" 800.1 5.5" 139.7 137 62.1 31.5" 800.1 5.5" 139.7 137 62.1 36.22" 920.0 5.5" 139.7 161 73.0 36.22" 920.0 5.5" 139.7 161 73.0 36.22" 920.0 5.5" 139.7 161 73.0 38.19" 970.0 5.5" 139.7 176 79.8 39.19" 970.0 5.5" 139.7 176 79.8 38.19" 970.0 5.5" 139.7 176 79.8 40.55" 1,030.0 5.5" 139.7 187 84.8
45.28" 1,150.0 7.52" 191.0 353 160.1 48.03" 1,220.0 7.52" 191.0 408 185.1
NOTE: 6" motors are 3450 rpm, 60 Hz, 1.15 SF. See pages 105-108 for Cable Selection Guides. *8" motor with 6" pump connection
OUTLINE DIMENSIONS
Shaft Extension 2.87" (72.9 mm)
L
For lengths, refer to Ordering Information tables.
Dimensions are for estimating purposes only.
Single phase motors require a control box.
ordering information
hp Kw volts ph
catalog number
Hitachi Control Box
5
3.7
230
1
HIT-5CBD
7.5 5.5
230
1
HIT-7.5CBD
10 7.5
230
1
HIT-10CBD
15
11
230
1
HIT-15CBD
D
43
M10373WS
Submersible motors and motor controls
6" PENTEK® Submersible Motor
Pentek® motors are designed for long service life and years of dependable operation. Innovative design and robust characteristics make this the perfect motor for your pumping applications.
Combining internal lubrication, a cooling blend of water, glycol, and propylene, and superior materials, Pentek submersible motors provide the industry with innovative and advanced design features that will extend the serviceable life of your installation.
Applications High-thrust water well applications.
SPECIFICATIONS Motor sleeve, fasteners 304 stainless steel Castings cast iron - epoxy electrodisposition coating Shaft NEMA splined, 431 stainless steel Thrust bearings Kingsbury-type disc carbon (resin impregnated) pad - 420 stainless steel Mechanical seal silicon carbide Diaphragm, sand slinger nitrile rubber
Features
Exceptional insulation / temperature rating exceeds NEMA requirements for high water temperature by 18°F (10°C).
Higher efficiencies and lower current consumption for reduced energy costs
High-capacity Kingsbury-type bearings for dependable performance
Superior materials / corrosionresistant design for extended life
Sand slinger protection / siliconcarbide mechanical seal / pressure-equalizing diaphragm advanced design features for superior performance, reliability, and quality
VFD-compatible
44
S10862ws
Submersible motors and motor controls
6" PENTEK® Submersible Motor
ORDERING INFORMATION
Motor
PENTEK
Type Phase Note Model # HP KW
6PM2-5-2 5 4
6PM2-7-2 7-1/2 6
6PM2-10-2 10 8 Motors are 60 Hz 6PM2-15-2 15 11 only
6MP2-20-2 20 15
Service Factor 1.00 Service Factor 1.15
Eff. P.F.
Eff. P.F.
HZ VOLTS AMPS % % AMPS % %
15 .2 75 83 16.4 77 85
21.2 79 85 23.2 79 86
30.8 77 81 33.0 78 83
60 230 43.2 78 84 47.0 78 86
57.4 79 85 63.0 79 87
Locked Rotor Amps 102.1
146.4
187.6
281.8
394.5
Winding
Length
Thrust KVA Insulation Resistance
Load Code Class (ohm) RPM in mm
K 1763
J
0.7873 3460 22.7 577 0.5389 3460 24.9 632
J
0.3964 3440 29.2 741.5
J
0.2782 3450 31.8 807.5
3485 J
0.2101 3450 35.1 892.5
Weight
lbs kg 90 41 102 46 116 53 121 55 147 67
6" Three
6PM2-25-2 25 19
69 81 86 76.0 80 88 480.2
J
6PM2-30-2 30 22
76.6 84 88 85.0 84 89 614.2
K
50 380 8.9 75 87
45.6
6PM2-5-4 5 4
K
60 460 10.6 75 83 8.2 77 85 51.1
1763
50 380 12.5 79 87
66.8
6PM2-7-4 7-1/2 6
J
60 460 15.4 79 85 11.6 79 86 73.2
50 380 17.8 78 85
85.6
6PM2-10-4 10 8
60 460 15.4 77 81 16.5 78 83 93.8
J F
0.1605 3450 38.0 964.5 165 75
0.1445 3500 41.8 1,060.5 190 86
2820
2.9674
22.7 577 90 41
3460
2820
1.9828
24.9 632 102 46
3460
2800
1.4648
29.2 741.5 116 53
3440
50 380 25.6 77 87
127
6PM2-15-4 15 11
J
60 460 21.6 78 84 23.5 78 86 140.9
Motors are
dual rated 50 Hz &
6PM2-20-4
20
50 380 15
60 460
34 28.5
78 89 79 85
31.5
79 87
170.2 197.3
3485
J
60 Hz
50 380 41 79 89
219
6MP2-25-4 25 19
J
60 460 34.5 81 86 38.0 80 88 240.1
50 380 46 83 90
276.8
6PM2-30-4 30 22
K
60 460 38 84 88 42.5 84 89 307.1
2810
0.9916
31.8 807.5 131 55
3450
2810
0.7192
35.1 892.5 147 67
3450
2820
0.5640
38.0 964.5 165 75
3450
2880
0.5036
41.8 1060.5 190 86
3500
50 380 62.5 83 90
393.1
6PM2-40-4 40 30
K
60 460 52.7 84 88 58.0 84 89 439.7
6182
50 380 77.6 83 90
449.8
6PM2-50-4 50 37
K
60 460 64.3 85 87 70.8 85 89 500.5
2860
0.3958
47.1 1197 209 95
3490
2840
.3295
49.9 1267 292 132
3480
See pages 109-110 for Cable Selection Guides.
OUTLINE DIMENSIONS
Nominal diameter Effective diameter Shaft extension length
6"/152.4 mm 5.43"/138 mm 2.87" / 73 mm
L
For lengths, refer to Ordering Information tables. Dimensions are for estimating purposes only.
45
S10862ws
Jet Pumps
MPN Series Shallow Well
MPN Series Shallow Well Jet Pumps are corrosion- and abrasion-resistant and are ideal for wells with pumping levels of 25' or less.
Self-priming after the pump housing is initially filled with water.
Capacities to 18 GPM at 30 PSI. Available in 1/2, 3/4 and 1 HP models. Supplied with the industry standard 30-50 pressure switch setting.
APPLICATIONS n Water systems... booster pump,
marine, mist sprayers poultry, fountains and water features
SPECIFICATIONS Body and Seal Plate Fiberglassreinforced thermoplastic Impeller Engineered composite Base 10-gauge steel Nozzle, Venturi, Diffuser Engineered composite
FEATURES
Quality Construction Fiberglassreinforced thermoplastic body provides total corrosion resistance and high resistance to abrasion
Built-in Jet Shallow-well jet has corrosion-resistant engineered composite nozzle and venturi
Impeller Precision- molded for perfect balance... ultra-smooth for highest performance and efficiency
Precision Molded Diffuser Engineered composite diffuser allows pump to prime faster, handle more air
Heavy-duty Motor Stainless steel shaft and dual heavy-duty ball bearings
Heavy-duty Ball Bearings Shielded, permanently lubricated bearings, extensively tested to ensure extended life and smooth, quiet operation
Dual Voltage Capability 1/2, 3/4 and 1 HP models have dual voltage motors and are shipped at the 230 Volt setting
Professional Quality Pre-set 30-50 PSI Allows for cut-in pressure adjustments
New Nozzle Clean-out Easy plug removal and access for ease of service
New Drain Plug Bottom-mounted for easy draining and winterization
ORDERING INFORMATION
Catalog
Number
HP
MPNC
1/2
MPND
3/4
MPNE
1
Description Base Mounted Pump Base Mounted Pump Base Mounted Pump
Pipe Tapping Sizes
Suct.
Disch.
1-1/4"
1"
1-1/4"
1"
1-1/4"
1"
Motor Voltage
115/230 115/230 115/230
Approx. Wt. Lbs. / Kg.
21 / 9.5 24 / 11 26 / 12
46
M9123WS
Jet Pumps
MPN Series Shallow Well
OUTLINE DIMENSIONS
[143.0] ø5.63
"L"
1" NPT
[167.6] 6.60
[104.8] 4.13
[50.7] 2.00
[38.1] 1.50
[185.9] 7.32
[247.9] 9.76
[227.6] 8.96
1-1/4'' NPT
[44.5] 1.75
60.6 2.38
1/4"NPT PLUG
[254.0] 10.00
[214.0] 8.43
[98.4] 3.87
[62.0] 2.44
[34.9] 1.38
[124.0] 4.88
[69.9] 2.75
[22.4] .88
[10.2] .40
[50.8] 2.00
[142.7] 5.62
"A"
PUMP PERFORMANCE
[12.7] ø.50
Capacity liters per minute
0 10 20 30 40 50 60 70 80 90
200
60
3/4 HP
1/2 HP
150 100
50 0
1 HP
25'
15'
25' 15'
5'
25'
15' 5'
5'
5
10
15
20
Capacity gallons per minute
50 40 30 20 10 0 25
Cat. No. MPNC MPND MPNE
L (in / cm) 19.4 / 49.3 20.1 / 51.2 20.6 / 52.4
A (in / cm) 17.9 / 45.5 18.7 / 47.4 19.2 / 48.7
Dimensions (in inches) are for estimating purposes only.
Capacity in Gallons / Liters Per Minute
Catalog Number
Total Discharge Pressure PSI / Bar
Suction
Shut-Off
HP Lift Ft / M 30 / 2.1 40 / 2.8 50 / 3.5 PSI / Bar
5 / 1.5 8.5 / 32.2 7.4 / 28.0 5.2 / 19.7
10 / 3.0 7.1 / 26.9 6.4 / 24.2 5.1 / 19.3 MPNC 1/2 15 / 4.6 6.5 / 24.6 6.1 / 23.1 4.5 / 17.0 77 / 5.30
20 / 6.1 5.4 / 20.4 5.1 / 19.3 4.1 / 15.5 25 / 7.6 4.1 / 15.5 4.0 / 15.1 3.4 / 12.9
5 / 1.5 12.1 / 45.8 10.7 / 40.5 8.5 / 32.2
10 / 3.0 10.7 / 40.5 10.2 / 38.6 8.4 / 31.8
MPND 3/4 15 / 4.6 9.0 / 34.1 8.5 / 32.2 8.1 / 30.7 78 / 5.37
20 / 6.1 7.6 / 28.8 7.3 / 27.6 7.1 / 26.9
25 / 7.6 5.3 / 20.1 5.7 / 21.6 5.1 / 19.3
5 / 1.5 18.0 / 68.1 16.8 / 63.6 13.5 / 51.1 10 / 3.0 17.1 / 64.7 16.1 / 60.9 13.4 / 50.7
MPNE
1
15 / 4.6 14.9 / 56.4 14.4 / 54.5 13.0 / 49.2 67 / 4.62
20 / 6.1 12.6 / 47.7 12.2 / 46.2 12.0 / 45.4
25 / 7.6 8.8 / 33.3 8.5 / 32.2 8.1 / 30.7
Pumps will operate at all depths shown, with pressure switch set at 30-50 PSI. Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Pumps installed with a conventional tank require a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
47
M9123WS
Total head in feet Total head in meters
Jet Pumps
Quick Draw Shallow Well
Myers® Quick Draw Jet Pumps prime quickly, deliver strong performance, and feature a moisture and insect proof motor for optimum reliable service. These pumps feature a large capacity top suction case and internal priming plate for quick and reliable priming. The motor provides dependable long life to all critical bearings with electrical connections enclosed and protected from potential moisture and insect problems. The 1/2, 3/4 and 1 HP pumps are quick to deliver water for home, farm, commercial and industrial water systems. For more details, contact your local distributor or the Myers sales office at 888-987-8677.
APPLICATIONS n Water systems... home, farm,
commercial and industrial
SPECIFICATIONS
n Improved shallow well design
n Cast iron construction
n Corrosion resistant impellers
n 1/2, 3/4 and 1 HP models
n Maximum pressures to 65 PSI
n Flows to 27 GPM
FEATURES Quick and Easy Priming: n Faster priming
n Large capacity, top suction case
n Internal priming plate
n Separate priming plug on case
Long Life Motor: n 115/230 volt with dual
voltage selector switch
n Prevents moisture, insect or dirt damage to critical electrical components
n Provides clean, dry environment to electrical components for maximum motor life
n Permanently lubricated double-ball bearings
n Strong capacitor starting torque
n Non-overloading, continuous duty rating
n Internal thermal overload protection
Strong Pump Performance: n Maximum pressures to 65 psi
n Flow capabilities to 26 gpm
n 1-1/4" suction, 1" discharge on all models
Heavy Duty Pump Case and Motor Bracket: n High tensile strength cast iron
Easy Serviceability: n Convenient back pullout design
n Nozzle clean-out and priming fitting
Mechanical Shaft Seal: n Precision lapped and polished carbon/
ceramic faces, buna elastomers, and stainless steel components
Direct Mount Pressure Switch: n Pre-set at 30/50 psi setting
Corrosion Resistant Design: n Engineered reinforced
thermoplastic impeller
n Thermoset diffuser with stainless steel wear ring
48
M9126WS
Jet Pumps
Quick Draw Shallow Well
ORDERING INFORMATION
Pump Catalog No.
QD50S
QD75S
QD100S
Discharge
HP
Pressure (Lbs.)
0'
20
12.5
30
11
1/2
40
9
50
6.5
20
20
30
19
3/4
40
16
50
9.5
20
26.5
30
25
1
40
20
50
12.5
OUTLINE DIMENSIONS
9.57
3.94
1-1/4" NPT
Suction
Capacity in U.S. Gallons Suction Lift
5'
10'
15'
11.5
10.5
9
10
9.5
8
8
7.5
6
5.5
5
4
18
16.5
15
17
15.5
14
14.5
12
11
8.5
7.5
6.5
24
22
19
23
21
18
18.5
16
13
11
9.5
7
B 1" NPT Discharge
A 5.90
Total head in feet Total head in meters
PUMPPERFORMANCE
Capacity liters per minute
0
20
40
60
80
100
150
45
3/4 HP Shallow Well 1/2 HP Shallow Well
40
125
100
1 HP Shallow Well
35 30 25
75
20
50
15
10 25
5
0
0
5
10
15
20
25
30
Capacity gallons per minute
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
160
50
49
140
45
Shut-Off
20'
25'
Pressure
7.5
6
6.5
5
65 psi
4.5
3
3
2
13
10
12
9
65 psi
9
8
4.5
3.5
16
13
15
11
62 psi
10.5
7
5
Cat. No. A QD50S 7.97 QD75S 8.50 QD100S 8.50
B 16.89 17.86 17.86
Dimensions (in inches) are for estimating purposes only.
M9126WS
Jet Pumps
MPL Series Convertible
Durability and corrosion resistance are built into every MPL Series Pump, due to the rugged fiberglass reinforced thermoplastic pump construc-tion. The engineered composite components are lightweight yet extremely resistant to sand and abrasive wear. The non-corrosive design and exceptional strength assure years of trouble-free operation.
APPLICATIONS
n Water systems and sprinkling... for homes, farms and cottages
SPECIFICATIONS Pump Body and Seal Plate Dura-Glas®
Impeller Engineered composite
Nozzle Engineered composite
Venturi Engineered composite
O-Ring Buna-N
Clamp Stainless Steel
Shaft Stainless Steel
Diffuser Engineered composite with brass wear ring
Shallow Well Jet Sold separately
Pressure Switch Pre-Set 30-50 PSI
Suction Ports Suction-over-drive
FEATURES
Superior Rustproof Construction Pump body is Dura-Glas® fiberglass reinforced thermoplastic lightweight, rustproof and exceptionally strong. All components in contact with water are resistant to the corrosive and abrasive forces found in the most aggressive water conditions.
Precision Diffuser Multi-port, reinforced engineered composite design primes faster and handles more air
Precision Molded Impeller Precision molded impeller gives perfect balance and ultra-smoothness for highest performance and efficiency
Pressure Regulator and Gauge Performance-proven, simple, built-in pressure regulator is adjustable for best performance on all deep well installations. Pressure gauge included.
Shaft Seal Stainless steel heat sink provides maximum cooling of the mechanical shaft seal
Heavy-duty Motor Dustproof canopy completely encloses electrical components and provides dust, dirt and insect protection. Ventilating air cannot contaminate vital switching components. Permanently lubricated, heavy-duty ball bearings ensure smooth, quiet operation and extended motor life.
Easy Serviceability MPL pumps are disassembled by removing the stainless steel clamp. Piping does not have to be disturbed. Seal replacement takes only a few minutes. "Control room" motor design makes all components easily accessible.
ORDERING INFORMATION
Catalog Number
MPLC MPLD MPLE MPLF
HP 1/2 3/4 1 1-1/2
Suct. 1-1/4" 1-1/4" 1-1/4" 1-1/4"
Pipe Tapping Sizes Drive 1" 1" 1" 1"
A Jet Package should be ordered with every MPL Series pump.
Disch. 1" 1" 1" 1"
50
Motor Voltage
115/230 115/230 115/230 115/230
Approx. Wt. Lbs. 27 28 30 36
M9127WS
Jet Pumps
MPL Series Convertible
OUTLINE DIMENSIONS
1 NPT DISCHARGE
40 60
psi
20
80
100
1-1/2
1-1/8
1-1/2 12 MAX
5-13/16 3-15/16
SUCTION 1-1/4 NPT
Shallow Well Jet 6-29/32
4-3/4 DIA.
DRIVE 1 NPT
3-1/16
1/4 NPT
(ordered separately)
1/2 DIA. 5-5/8
7-13/16
11-7/16
A
Dimensions (in inches) are for estimating purposes only.
1-3/8
2-3/4
3-1/4
6-1/2
B
5
Cat. No. MPLC MPLD MPLE MPLF
HP 1/2 3/4 1 1-1/2
A 14-7/8 15-5/8 16-1/8 17-1/8
B 5-1/8 5-1/8 5-1/8 5-7/16
PUMPPERFORMANCE Shallow Well
Capacity in Gallons Per Minute
Catalog Number MPLC
MPLD
MPLE
MPLF
Shallow Well Press Switch Dynamic Suct.
HP
Jet No.
Setting
Lift Ft.
20
5'
9.5
10'
8.2
1/2
PKG 1-21N
30-50
15'
7.2
20'
5.7
25'
4.3
5'
16.2
10'
14.2
3/4
PKG 1-22N
30-50
15'
12.2
20'
9.7
25'
7.2
5'
21.3
10'
18.8
1
PKG 1-23N
30-50
15'
16.0
20'
12.8
25'
8.5
5'
26.3
10'
23.7
1-1/2
PKG 1-24N
30-50
15'
20.3
20'
16.2
25'
11.5
Discharge Pressure PSI
30
40
50
9.2
9.0
5.8
8.0
7.8
5.2
6.8
6.8
4.5
5.7
5.7
3.8
4.3
4.3
3.2
15.8
15.3
8.7
14.0
13.8
7.2
12.0
11.8
5.3
9.7
9.2
3.7
6.8
6.8
21.0
20.7
13.2
18.7
18.3
11.1
15.8
15.7
8.9
12.7
12.3
5.7
8.5
8.5
26.2
26.2
21.3
23.3
23.2
19.2
20.2
20.0
16.3
16.0
15.8
11.2
11.3
11.3
Shut-Off
60
PSI
3.0
72
2.3
70
1.8
68
66
62
1.3
62
60
58
55
52
4.2
62
1.7
60
58
55
52
7.7
64
3.5
62
60
57
54
Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Pumps installed with a conventional tank require a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
51
M9127WS
JET PUMPS
Jet Pumps
MPL Series Convertible
PUMPPERFORMANCE Deep Well
Capacity in Gallons Per Minute
Catalog
Uses Uses
Pumping Depth in Feet
Number HP Jet No. Venturi Nozzle 20'
30'
40'
50'
60'
70'
80'
90'
100' 110' 120'
4" DOUBLE PIPE 40 PSI
MPLC
4SD J32P-24 J34P-41 1/2
10SD N32P-6B J34P-44
4.5
3.5
2.3
1.3
9.5
7.0
4.5
2.0
MPLD
3/4
4SD J32P-24 J34P-41
6.5
5.1
4.0
3.0
1.8
0.8
MPLE
1
4SD J32P-24 J34P-41
8.4
7.3
6.2
5.0
4.1
2.9
2.0
1.1
MPLF 1-1/2 11SD N32P68B J34P-44
11.5
9.4
8.0
6.5
5.3
3.8
2.5
1.1
2" SINGLE PIPE 40 PSI
13AP J32P-26 J34P-44 5.8
3.8
1.0
MPLC
1/2 10AP J32P-24 J34P-44 4.3
3.0
1.6
8AP J32P-18 J34P-42 3.8
3.3
2.6
2.0
1.5
14AP J32P-32 J34P-45 9..2
6.7
4.3
MPLD
3/4 10AP J32P-24 J34P-44 6.2
4.8
3.7
2.3
1.2
8AP J32P-18 J34P-42 4.1
3.7
3.1
2.6
2.1
1.6
1.2
0.8
15AP J32P-33 J34P-41 12.3
9.2
5.7
MPLE
1
9AP J32P-29 J34P-44 10.6
7.4
4.7
2.2
8AP J32P-18 J34P-42 5.0
4.7
4.2
3.8
3.3
2.7
2.3
1.8
1.3
16AP J32P-38 J34P-45 15.3 11.8
8.5
5.2
MPLF 1-1/2 9AP J32P-29 J34P-44
12.3
9.3
6.4
4.0
8AP J32P-18 J34P-42
5.7
5.0
4.6
4.2
3.7
3.3
2.8
2.4
1.8
1.3
3" SINGLE PIPE 40 PSI
25CP J32P-26 J34P-44 5.8
4.0
2.1
MPLC
1/2
19CP J32P-24 J34P-41
4.5
3.5
2.3
1.3
11CP J32P-32 J34P-45 9.5
7.0
4.5
2.0
MPLD
3/4
19CP J32P-24 J34P-41
6.5
5.1
4.0
3.0
1.8
0.8
26CP J32P-33 J34P-41 13.0
9.8
6.0
MPLE
1
17Cp J32P-29 J34P-44
11.5
8.0
5.2
2.6
19CP J32P-24 J34P-41
8.4
7.3
6.2
5.0
4.1
2.9
2.0
1.1
10CP J32P-38 J34P-45 16.6 13.3
9.5
6.0
MPLF 1-1/2
15CP J32P-22 J34P-43
8.6
7.9
6.9
6.2
5.4
4.4
3.2
2.2
1.5
0.9
Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Pumps installed with a conventional tank require a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
52
M9127WS
Jet Pumps
HR Series Convertible
Myers® HR Series jet pumps provide reliable service for many residential homes and farms, as well as commercial and industrial applications.
APPLICATIONS n Supply water systems and
sprinkling systems for homes, farms and industry
SPECIFICATIONS n Cast iron pump case
n Dual compartment, 115/230 Volt double-ball bearing motor with voltage selector switch
nPriming screen
n Diffuser with stainless steel wear ring
n Square D pressure switch
FEATURES
Quality Construction Durable machined heavy-duty construction pump body provides long product life
Impellers Precision molded impellers and diffuser provide smooth, balanced performance and efficiency
Pressure Switch High quality proven pressure switch with adjustable on/off pressure settings. 20 PSI differential.
Motor Heavy-duty motor with double ball bearing design and voltage selection device
Shaft Seal Mechanical shaft seal with ceramic face and stainless steel construction for long seal life
ORDERING INFORMATION Shallow Well
Catalog Number
HR50S
Discharge Pressure
HP
in Lbs.
20
1/2
30 40
50
Capacity in U.S. Gallons per Minute Suction Lift in Feet
5
15
20
11.5
9
6
11.5
9
6
10.5
7.5
5
5.5
3.5
2
Shut-Off PSI
70
ORDERING INFORMATION Deep Well
Pressure
Average
Jet Package Cat. Number
Catalog
Switch
Regulator
Packer for
Number
HP
Setting
Setting
Cast Iron
Bronze
2" Well
HR50D
1 / 2
20/40 30/50
22
DW50-1
DW50
P50
22
DW50-1
DW50
P50
Capacity in U.S. Gallons per Minute Distance to Low Water Level in Feet
30
40
50
60
70
80
10
8
7
5.5 4.5 3.5
9.5 7.5 6.5
5
4
3.5
53
M9129WS
Jet Pumps
HR Series Convertible
OUTLINE DIMENSIONS
9.66
Shallow
Well
8.31
E
ENRoI.
26220A
AL eS
IN USA
Oh i o
NSoE.RdI
MA DE
As hl a nd,
2
s
My e r ENC.
MODEL / MODEL E
F. E. CSA
R
17.25
4.38
2.13
8.31
4.38
MODEL / MODEL E
R
F. E. CSA
SE No .
RI d
My e r ENC.
eA LS ENRoI .
s
As hl a nd,
2
MA DE
Oh i o
IN USA
26220A
E
5.72 9.66
24358D
Deep Well
14.50
Dimensions (in inches) are for estimating purposes only.
PUMP PERFORMANCE
0 160
Capacity liters per minute
10
20
30
40
50
140
120 100
1/2 HP Shallow Well
80
60
40
20
0
2
4
6
8
10 12 14
Capacity gallons per minute
60 50 45 40 35 30 25 20 15 10 5 0
16
Total head in meters
Repair Parts Kit for HR Series
Kit
Includes
PK50 Shaft seal, impeller, diffuser, gasket, O-ring, venturi, and nozzle
54
M9129WS
Total head in feet
Jet Pumps
HJ Series Convertible
Myers® HJ Series is one of the most popular pump series in the market today. The HJ Series is known for its superior performance and dependability in home, farm, business and industrial applications around the world.
APPLICATIONS
n Supply water systems and sprinkling systems for homes, farms, businesses and industry
SPECIFICATIONS
n Heavy duty cast iron case and motor bracket
n Dual compartment, 115/230 volt double-ball bearing motor with voltage selector switch
n Dual adjustment pressure switch. Includes priming tee on shallow well models and pressure regulator on deep well models
nPriming screen
n Stainless steel impeller wear ring
FEATURES
Quality Construction Durable machined heavy-duty construction pump body provides long product life
Impellers Precision molded impellers and diffuser provide smooth, balanced performance and efficiency
Pressure Switch High quality proven pressure switch with adjustable on/off pressure settings. 20 PSI differential
Motor Heavy-duty motor with double ball bearing design and voltage selection device
Shaft Seal Mechanical shaft seal with ceramic face and stainless steel construction for long seal life
55
M9130WS
Jet Pumps
HJ Series Convertible
ORDERING INFORMATION Shallow Well
Catalog Number HJ50S*
HJ75S*
HJ100S*
Discharge Pressure
HP
in Lbs.
20
1/2
30 40
50
20
3/4
30 40
50
20
1
30 40
50
Capacity in U.S. Gallons per Minute Suction Lift in Feet
5
15
20
14.5
11.5
6
14.5
11.5
6
10
8
5
5.5
3.5
2
23.5
17.5
10.5
23.5
17.5
10.5
19.5
16.5
10.5
12.5
9
5
27.5
21
13
27.5
21
13
25.5
21
13
19
15.5
12
*For brass impeller add "-1" to Catalog Number, i.e.: HJ50D-1
Shut-Off PSI 65
69
67
ORDERING INFORMATION Deep Well
Catalog Number
Pressure Average Switch Regulator
Jet Package Cat. Number Packer for
Capacity in U.S. Gallons per Minute Distance to Low Water Level in Feet
HP Setting Setting Cast Iron Bronze 2" Well 30 40 50 60 70 80 90 100 110 120
20/40
HJ50D*
1/2
30/50
22
DW50-I DW50
22
DW50-I DW50
P50
10.5 9.5 8
6
5
4
2.5
P50
9
8
7
5.5 4.5 3.5
20/40
HJ75D*
3/4
30/50
26
DW75-I DW75
26
DW75-I DW75
P75
16.5 13.5 10
8
7
6
4
3
1
P75
15.5 12 10.5 7.5 6
5
3
2
HJ100D*
1
20/40 30/50
34
DW100-I DW100
P100
18 15.5 12.5 10
9
8
5.5 4.5 2.5 1
34
DW100-I DW100
P100
18 15 12 10
9
7.5 5
4
2
1
*For brass impeller add "-1" to Catalog Number, i.e.: HJ50D-1
Total head in feet Total head in meters
PUMP PERFORMANCE
0 160 140 120 100
80 60
Capacity liters per minute
25
50
75
100
50
1/2 HP3/4S1HhaPHllPowShSahllaolwlowWeWllell
40 30
Well
20
40 10
20
0
0
5
10
15
20
25
30
Capacity gallons per minute
56
Repair Parts Kits
Model
Kit
HJ50D PK50
HJ75D PK75
HJ100D PK100
Includes
Shaft seal, impeller, diffuser, gasket, O-ring, venturi, and nozzle
M9130WS
Jet Pumps
HJ Series Convertible
OUTLINE DIMENSIONS
16.47
HJ50 Shallow Well
8.28
7.75
HJ75 and HJ100 Shallow Well
19.41
10.24
9.67
5.30 10.22
8.72 6.01
Dimensions (in inches) are for estimating purposes only.
57
M9130WS
Jet Pumps
HJ Series Convertible
OUTLINE DIMENSIONS
HJ50 Deep Well
13.72
5.53
9.67
7.75
HJ75 and HJ100 Deep Well
15.33
5.30 10.17
8.72
4.50 2.16
Dimensions (in inches) are for estimating purposes only.
58
M9130WS
Jet Pumps
HC and HCM Series
Myers® convertible jet pumps provide all the water and pressure needed for today's family living needs. High quality materials and simplified construction combine for excellent performance in shallow and deep wells. The same twin ejector is used for both types of well service.
APPLICATIONS
n Water systems and sprinkling... for homes, farms and industry
SPECIFICATIONS
M otor 2-Compartment 115/230 Volt
Rotary Seal Stainless Steel/ Buna N
Impeller Brass
Motor Bracket Cast iron
Discharge Diffuser Cast iron
Second Stage Diffuser (HCM's) Cast iron
Diffuser Housing Cast iron
Motor Shaft Stainless Steel
Pressure Switch Square D dual adjustment
FEATURES
Heavy Duty Cast Iron Case Construction
Primes Easily Under maximum shallow well conditions
Brass Impeller Balanced for smooth operation
Fast Connect Flanges Eliminates threading and fitting at pipe end
Stream-flo Design Provides optimum hydraulic performance
Durable Cast Iron Pressure Regulator Included
P ressure Switch and Pressure Gauge Included
ORDERING INFORMATION
Catalog Number
HC50 HC50
HCM HCM50 HCM100
HCM150
Pressure Packer Type Twin Type Foot Valve Size Motor Capacitor Shipping Wt.
Switch Inner Pipe Size Drop Pipe - Twin Type
Type Built-in Pump Unit
Discharge Setting for 2" Well
Size
Only
Overload Protection Only
3/4"
20-40
3/4"
30-50
1"
40-60
1"
40-60
1"
1-1/4"x 1"
1-1/4"
115/230 volt
54
1"
1-1/4" x 1"
1-1/4"
115/230 volt
57
1"
1-1/4" x 1-1/4"
1-1/4"
115/230 volt
78
1"
1-1/4" x 1-1/4"
1-1/4"
115/230 volt
85
Shipping Weight Jet Packages for
4" Well
2" Well
Bronze Cast Iron
5
4
4
5
4
4
5
4
4
5
4
4
59
M9131WS
Jet Pumps
HC and HCM Series
PUMP PERFORMANCE HC50 Shallow Well
Catalog Number
5 Foot Suction Lift
Discharge Pressure, PSI Jet
Package 20
30
40
50
60
HP Cat. No.
HC50
1/2
SW50 13.5 13 11.5 10 6.6
15 Foot Suction Lift
Discharge Pressure, PSI
20 30 40 50 60 Capacity in U.S. Gallons per Minute
10
10 9.3
8
4.6
20 Foot Suction Lift Discharge Pressure, PSI 20 30 40 50 60
5.5 5.5 5.5
5
2
PUMP PERFORMANCE HC50 Deep Well
Catalog Number
Jet Package Cat. No.
Twin Type
Packer
Max. Average
HP
Amps Regulator
4" Min. Well
115/230 V Setting Cast Iron Bronze
2" Well
HC50
1/2
10.6 / 5.3 22 PSI DW50-I DW-50
P50
Vertical Distance in Feet from Pump to Low Water Level 30 40 50 60 70 80 90 100 110
Capacity in U.S. Gallons per Minute
12 11 9.8 8.3 6.5 4.5 2.3
PUMP PERFORMANCE HCM Shallow Well
5 Foot Suction Lift
15 Foot Suction Lift
20 Foot Suction Lift
Catalog Number
Discharge Pressure, PSI
Discharge Pressure, PSI
Discharge Pressure, PSI
Jet
Package 30 40 50 60 70 80 30 40 50 60 70 80 30 40 50 60 70 80
HP Cat. No.
Capacity in U.S. Gallons per Minute
HCM50
1/2
SW50 10.5 10 9.5 9 4
8 8 7.5 7 3.5
6.5 6.5 5.5 5.5 2
HCM100
1
SW100 19 19 16.5 16 13 10 13 13 13 12 10 8 8 8 8 8 8 6.5
HCM150 1-1/2 SW150 22.5 22.5 22.5 20 20 13 17 17 16.5 16 14 11 9.3 9.3 9.3 9.3 8.8 8.3
PUMP PERFORMANCE HCM Deep Well
Catalog Number
Jet Package Cat. No.
Max. Average Amps Regulator
Twin Type 4" Min. Well
HP 115/230 V Setting Cast Iron Bronze
Packer 2" Well
HCM50 HCM100 HCM150
1/2 1 1-1/2
10.6 / 5.3 17.0 / 8.5 19.8 / 9.9
22 PSI 34 PSI 40 PSI
DW50-I DW100-I DW150-I
DW50 DW100 DW150
P50 P100 P150
Vertical Distance in Feet from Pump to Low Water Level 30 40 50 60 70 80 90 100 110 120 130 140 150
Capacity in U.S. Gallons per Minute
11.5 9.5 8 6.5 6.5 4 3 2 1 15 13.3 12 10.6 9.3 8 6.6 5.3 4 2.6 2 17.5 16 14.5 12.8 11.6 9.5 8 7 6 5 4 3 2
60
M9131WS
Total head in meters
Jet Pumps
HC and HCM Series
Total head in feet
HCM50 1/2 HP HC50 1/2 HP
PUMP PERFORMANCE
0 200 175 150 125 100
75 50 25
0
Capacity liters per minute
1000
2000
3000
4000
5000
60
50
40
30
20
15'
10'
5'
10
5
10
15
20
Capacity gallons per minute
0 25
0 200 175 150 125 100
75 50 25
0
Capacity liters per minute
1000
2000
3000
4000
5000
60
50
HCM100 1 HP
40
30
15'
10'
5'
20
10
5
10
15
20
Capacity gallons per minute
0 25
Total head in meters Total head in feet
Total head in meters Total head in feet
0 200 175 150 125 100
75 50 25
0
Capacity liters per minute
1000
2000
3000
4000
5000
60
50
40
30
15' 10'
5'
20
10
5
10
15
20
Capacity gallons per minute
0 25
0 200 175 150 125 100
75 50 25
0
Capacity liters per minute
1000
2000
3000
4000
5000
60
HCM
150
50
1-1/2 HP
40
30
15'
10'
5'
20
10
5
10
15
20
Capacity gallons per minute
0 25
Total head in feet
Total head in meters
61
M9131WS
Jet Pumps
HC and HCM Series
OUTLINE DIMENSIONS
HC50 AND HCM50
9.28
19.67
8.85 4.04 2.04
HCM100 AND HCM150
10.56
3 4
19.86
9.30
4.50 2.50
Dimensions (in inches) are for estimating purposes only.
62
M9131WS
tanks
PRO-SOURCE® Fibrewound Pressure
PSC-119-35
PSC-60-20
PSC-80-23
PSC-85-25
PSC-48-14
PSC-40-12
PSC-30-9
PSC-20-6 PSC-14-4
Built Tough...for Quality Every Pro-Source® Composite tank utilizes a durable, FDA approved air cell which is resistant to chlorine and will not promote taste or odor problems associated with iron bacteria that may be present in the water supply.
Built Tough...for Durability Each tank is wrapped with more than three miles of overlapping, continuous fiberglass strands, sealed with high-grade epoxy resin, then oven-cured. Tough composite construction means longer lasting tanks that will not rust, corrode, dent or scratch.
Built Tough...for Easy Installation and Service
Not only is composite construction tougher, it's also more lightweight...as little as half the weight of steel tanks. Installation is faster, easier and can be handled by one person. Repairable with the tank installed.
Tested and certified by WQA to NSF/ANSI Std. 61 Section 8 and ORDO92 for "lead free" compliance.
ORDERING INFORMATION
Catalog Number
PSC-14-4 PSC-20-6 PSC-30-9 PSC-40-12 PSC-48-14 PSC-60-20 PSC-80-23 PSC-85-25 PSC-119-35
Tank Capacity Gal./Liter
14.5 / 55 19.8 / 75 29.5 / 112 40.3 / 153 47.1 / 178 60 / 227 79.6 / 301 86.7 / 328 119.7 / 453
Tank Diameter Inch / cm
16 / 41 16 / 41 16 / 41 16 / 41 21 / 53 24 / 61 21 / 53 24 / 61 24 / 61
Tank Height Inch / cm
28.2 / 71.6 34.1 / 86.6 46.3 / 117.6 59.0 / 149.9 43.6 / 110.7 44.4 / 112.8 65.5 / 166.4 57.2 / 145.3 75.4 191.5
Discharge Tapping Inch / cm
1 / 2.5 1 / 2.5 1 / 2.5 1 / 2.5 1.25 / 3.1 1.25 / 3.1 1.25 / 3.1 1.25 / 3.1 1.25 / 3.1
Water Yield Per Pump Cycle Pressure Switch Setting
20-40 Gal./Liter
4.9 / 18.7 6.7 / 25.5 10.0 / 38.1 13.7 / 52.0 16.0 / 60.5 20.4 / 77.2 27.1 / 102.3 29.5 / 111.5 40.7 / 154
30-50 Gal./Liter
4.4 / 16.5 5.9 / 22.5 8.9 / 33.5 12.1 / 45.8 14.1 / 53.5 18.0 / 68.1 23.8 / 90.4 26.0 / 98.5 35.9 / 135.9
40-60 Gal./Liter
3.8 / 14.3 5.1 / 19.5 7.7 / 29.1 10.5 / 39.8 12.2 / 46.3 15.6 / 59.0 20.7 / 78.3 22.5 / 85.3 31.1 / 117.8
Maximum Operating Pressure = 125 PSI, PSC - 80-23 has a maximum operations pressure of 100 PSI.
Maximum Internal Water Temperature: 120°F (49°C). Maximum Ambient Air Temperature: 120°F (49°C) Distance from base to center line of connection is 2-1/4" (5.7 cm)*. *1-3/4" (4.4 cm) for 16" diameter tanks
Allow 12" (30.5 cm) for service clearance.
Certified to ANSI/NSF 61, Drinking Water System Components
63
M9132WS
tanks
PRO-SOURCE® Fibrewound Pressure
Applications
n U se wherever pressurized tanks are needed in water systems applications.
SPECIFICATIONS Inner Liner: One-piece high-density polyethylene Outer Shell: Fiberglass-wound, ovencured, and epoxy resin sealed Exclusive Air Cell: Heavy gauged PEU, meets Water Quality Association standards Base: Rotatable base with quick connect Service Connection: Stainless steel, 300 grade
FEATURES
Durable Composite Construction: A rugged one-piece molded inner liner of premium high-density polyethylene.
n Miles of continuous overlapping fiberglass strands, sealed with oven-cured epoxy, make the outer shell impervious to rust, dents and ultra-violet rays (no paint to scratch and touch up).
Air Cell: Seamless, durable PEU air cell is full replaceable and constructed of heavygauge engineered polymer. Meets Water Quality Assocation standards.
Tank Base: Rigid molded ABS is the sturdiest composite base on the market. Corrosion- and impact-resistant.
Replaceable Air Cell: Generous and accessible air cell opening facilitates easy removal and re-installation of replacement air cell (with the professional contractor in mind).
Stainless Steel Service Connection: 300 grade, the professional's choice
TANK SIZING RULE:
Size tank for one gallon of drawdown for each gallon per minute at pump capacity.
Example: For a 1 HP, 20 GPM unit pumping 20 gallons per minute on a 30-50 pressure switch setting, the properly sized Pro-Source composite tank is a PSC-80-23, which has a 23.8 gallon drawdown.
64
M9132WS
tanks
PRO-SOURCE® Fibrewound Pressure
OPERATING CYCLE
1.Pro-Source® Composite tank is nearly empty: air cell is fully expanded
2. Water is pumped into tank: air in cell is compressed
3. Pump-up cycle is complete: air is now compressed to "cut off" setting of pressure switch
4. W ater is drawn from tank: pressure in air cell provides water as needed, until tank is empty and cycle repeats
Air
Air
Air
Air
Air
Air Air
Air
Air
Air
Air
Air Air
Air
Air
Air
Water
Water
Water
Water
Water
Water
Water
Water
Fig. 2A
Fig. 2FBig. 2A
Fig.F2igC. 2B Fig. 2A Fig. F2iDg. 2C Fig. 2B Fig.F2iAg. 2D Fig. 2C Fig. 2B
Fig. 2D Fig. 2C
Fig. 2D
CHART A
2775 0297
2775 0297
2775 0297
2775 0297
Tank Selection Chart
SYSTEM PRESSURE SWITCH SETTING PSI
Pump GPM
20-40
30-50 Runtimes
40-60
1 Minute
2 Minute
1 Minute
2 Minute
1 Minute
2 Minute
5
PSC-20-6
PSC-30-9
PSC-20-6
PSC-40-12
PSC-20-6
PSC-40-12
7.5
PSC-30-9
PSC-48-14
PSC-30-9
PSC-60-20
PSC-30-9
PSC-60-20
12.5
PSC-40-12
PSC-80-23
PSC-48-14
PSC-85-25
PSC-60-20
PSC-119-35
15
PSC-48-14
PSC-119-35
PSC-60-20
PSC-119-35
PSC-60-20
PSC-119-35
20
PSC-60-20
PSC-119-35
PSC-80-23
PSC-80-23 (2)
PSC-80-23
PSC-80-23 (2)
30
PSC-85-25
PSC-85-25 (2)
PSC-119-35
PSC-119-35 (2)
PSC-119-35
PSC-119-35 (2)
50
PSC-80-23 (2)
PSC-119-35 (3)
PSC-85-25 (2)
PSC-119-35 (3)
PSC-119-35 (2)
PSC-119-35 (3)
Note: Drawdown will be affected by operating temperature of the system, accuracy of the pressure switch and gauge, the actual precharge pressure, and rate of fill.
CHART B
Drawdown Volume Multiplier* (Approximate)
Pump Off
Pressure
PSI
10
20
20
0.26
PUMP START PRESSURE PSI
30
40
50
60
70
80
30
0.41
0.22
40
0.37
0.18
50
0.46
0.31
0.15
60
0.40
0.27
0.13
70
0.47
0.35
0.24
0.12
80
0.42
0.32
0.21
0.11
90
0.48
0.38
0.29
0.19
0.10
100
0.44
0.35
0.26
0.17
*Utilize this chart if proper selection cannot be made using tank selection chart. Drawdown based on Boyle's Law.
Procedure:
1. Identify drawdown multiplier relating to specific application.
2. Insert multiplier (X) into the following formula: Pump GPM x Min Runtime = Minimum Tank
Multiplier (X)
Capacity Required
3. Refer to "Ordering Information" Table Max. Capacity Gals.
65
M9132WS
tanks
PRO-SOURCE® Fibrewound Pressure
Contact and sideport contact
Built Tough... for Quality Professional grade composite construction means longer lasting tanks that will not rust, corrode, dent or scratch.
Built Tough... for Durability Each tank is wrapped with more than three miles of over-lapping, continuous fiberglass strands, sealed with high grade epoxy resin, then oven cured.
Built Tough... for Easy Installation Composite construction is lightweight... as little as half the weight of steel tanks. Installation is faster, easier and can be handled by one person.
APPLICATIONS
n Residential Water Systems Industrial,Commercial and Agricultural
SPECIFICATIONS
Inner Liner: One-piece high-density polyethylene
Outer Shell: Fiberglass-wound and epoxy resin sealed
Upper and Lower Flanges: Reinforced polypropylene
Base: One-piece ABS
Service Connections: Reinforced polypropylene
FCT Series Contact Tanks
SP Series SidePort Contact Tanks
SP26
SP35
FCT-40
FCT-80
FCT-120
Tested and certified by WQA to NSF/ANSI Std. 61 Section 8 and ORDO92 for "lead free" compliance.
SP9
SP18
FEATURES
Durable Composite Construction: A rugged one-piece molded inner liner of premium high-density polyethylene. Miles of continuous overlapping fiberglass strands, sealed with oven-cured epoxy, make the outer shell impervious to rust, dents and ultra-violet rays (no paint to scratch and touch up).
Tank Base: Rigid ABS is the sturdiest composite base on the market. Corrosionand impact-resistant. Base rotates 360° for ease-of-service hook-up.
Composite Service Connection: Threaded for ease of installation.
ORDERING INFORMATION
FCT SERIES CONTACT TANKS
Catalog Number
Maximum Capacity Gal./Liter
Maximum Operating Pressure PSI/kPa/Bar
FCT-40
40/151
75/500/5.0
FCT-80
80/303
75/500/5.0
FCT-120
120/454
75/500/5.0
Diameter Inch/cm
16/41 21/53 24/61
Overall Height Inch/cm
57.25/145
62.75/159
73.25/186
Height Inlet/ Outlet to Floor
Inch/cm
Top System Connection
Bottom System Connection
1.5/3.8 2/5.1 2/5.1
1-1/4" Socket 1-1/4" Socket 1-1/4" Socket
1-1/4" Socket 1-1/4" Socket 1-1/4" Socket
Maximum external operating temperature 120ºF (49ºC). Maximum internal operating temperature 100ºF (38ºC). Minimum operating temperature 40ºF (4ºC).
Assembly Weight Lbs./kg
28/12.7
43/19.5
63/28.6
Tested and certified by WQA to NSF/ANSI Std. 61 Section 8 and ORDO92 for "lead free" compliance. In order to provide the best products possible, specifications are subject to change.
66
M9135WS
tanks
PRO-SOURCE® Fibrewound Pressure
ORDERING INFORMATION
SP Series SidePort Contact Tanks
Catalog Number
Maximum Capacity Gal./Liter
SP-7
30/114
SP-9
40/151
SP-9SQ
47/178
SP-18
80/303
SP-26
120/454
SP-35
205/776
SP-50
264/999
Drawdown 30-50 Setting Gallons/Liters
7/26 9/34 9/34 18/67 26/98 35/132 50/189
Diameter Inch/cm
16/41 16/41 21/53 21/53 24/61 36/91 36/91
Overall Height Inch/cm 43.75/111 56.5/144 41.25/105 62/157 72.5/184 73/185 82/208
Height Inlet/Outlet Height Sideport to
to Floor
Floor
Unit Ship Weight
Inch/cm
Inch/cm
Lbs./kg
1.5/3.8
14/35.6
26/11.8
1.5/3.8
15.5/39.4
35/15.9
2/5.1
16.9/42.9
48/21.8
2/5.1
18.3/46.5
67/30.5
2/5.1
20.2/51.3
97/44.1
7/17.8
31.5/80.0
290/131.8
7/17.8
31.5/80.0
300/136.4
Maximum Operating Pressure = 100 PSI 1-1/4" System connections sidewall. Customer-supplied air control valve. Bottom, dual port 1-1/4" PVC.
U238-5 Air Volume Controls
(Jet pump type)
E238-2 Air Volume Control (Submersible type)
67
M9135WS
tanks
PRO-SOURCE® Plus Premium Steel Pressurized
APPLICATIONS Residential Water Systems Industrial, Commercial and Agricultural
SPECIFICATIONS Shell: Heavy-gauge steel Base: High-impact composite, ABS Finish: Electrostatically applied, baked-on polyester paint Water Cell: One-piece seamless PVC, made from FDA listed material Flange: 304SS Service Connection: NPT threads, integral to flange Air Valve: Nickel-plated brass, threaded for ease of service
PSP32
PSP119 PSP62
PSP85
PSP35
PSP19T
PSP19S
PSP50
Stainless Steel Service Connection "The Professional's Choice" Metal Air Valve Assembly "Field-Serviceable" 125 PSI Maximum Operating Pressure Four Sizes: PSP50, PSP62, PSP85 and PSP119
In order to provide the best products possible, specifications are subject to change.
ORDERING INFORMATION
Catalog Number
Maximum Capacity Gal./Liter
VERTICAL MODELS
PSP19S-T02
19/72
PSP19T-T02
19/72
PSP32-T03
32/121
PSP35-T05
35/133
PSP50-T50
50/189
PSP62-T51
62/235
PSP85-T52
85/322
PSP119-TR50 119/450
Diameter* Inch/cm
20/51 16/40.6 16/40.6 20/51 24/61 24/61 24/61 24/61
Height* Inch/cm
21/53.3 27.5/70 43/109 33/84 32.5/83 39.5/100 51/130 68/173
Precharge Connection PSI/kPa Size Female
20-40
Drawdown In Gallons/Liters
30-50
40-60
40/276 40/276 40/276 40/276 40/276 40/276 40/276 40/276
1" NPT 1" NPT 1" NPT 1" NPT 1-1/4" NPT 1-1/4" NPT 1-1/4" NPT 1-1/4" NPT
6.9/26.1 6.9/26.1 11.6/43.9 12.7/48.1 18.3/69.3 21.4/81.0 30/113.6 41.3/156.3
5.8/21.9 5.8/21.9 9.8/37.1 10.7/40.5 15.5/58.7 18.3/69.3 26/98.4 35.4/134.0
5.0/18.9 5.0/18.9 8.5/32.2 9.3/35.2 13.4/50.7 16.0/60.6 22.0/83.3 31.0/117.3
Weight Lbs./kg
Maximum Operating
PSI
49/22.2
100
44/20.0
100
60/27.2
100
70/31.8
100
88/39.9
125
116/52.6
125
128/58.1
125
140/63.5
125
*Subject to change without notice. Maximum Liquid Temperature:120°F (49°C) Maximum External (Ambient) Temperature:125°F (52°C)
68
M9133WS
tanks
PRO-SOURCE® Plus Premium Steel Pressurized
fEATURES
Service Connection: 304 stainless steel.
Air Valve: Nickel-plated brass.
Maximum Operating Pressure: 100 PSI on 16" and 20" tanks; 125 PSI on 24" tanks. (models; PSP50, PSP62, PSP85, PSP119)
Heavy-Gauge Metal Construction: n Sturdy "welded wrapper and head
design." Built to last.
Polyester Paint Finish: Electrostatically powder-painted, then oven-baked for a smooth high-gloss, appliance-quality finish. Resists corrosion.
Elongated, Seamless Water Cell: n Controlled 2-dimensional cell expansion.
n Rugged, seamless "water cell" prevents the most common cause of tank failure "waterlogging."
n Water never touches the steel tank material.
n Translucent bag material facilitates manufacturing quality control inspection.
NEW Stainless Service Connection: n Corrosion-resistant.
n Stainless steel the professional's choice.
Integral Standpipe: Promotes complete flushing of the water entering/exiting the tank.
Nitrogen-Rich Precharge: Decreases air permeation three to four times over straight air precharge.
40 PSI Precharge: Ready for use with 40/60 pressure range systems. Enables installer to reduce pressure depending on pressure switch setting.
Sturdy Base: Tested-tough composite construction.
Tank Sizing Rule:
Size tank for one gallon of drawdown for each gallon per minute at pump capacity.
Example: For a 1 HP, 20 GPM unit pumping 20 gallons per minute on a 30-50 pressure switch setting, the properly sized Pro-Source® PLUS tank is a PSP85-T52 which has a 26 gallon drawdown.
CHART A
Tank Selection Chart
Pump GPM
SYSTEM PRESSURE SWITCH SETTING PSI
20-40
30-50
40-60
Runtimes
1 Minute 2 Minute 1 Minute 2 Minute 1 Minute 2 Minute
5
PSP19T PSP32 PSP19T PSP35 PSP19T PSP50
7.5
PSP32 PSP50 PSP32 PSP50 PSP32 PSP62
10
PSP32 PSP62 PSP35 PSP85 PSP50 PSP85
12.5 PSP35 PSP85 PSP50 PSP85 PSP50 PSP119
15
PSP50 PSP85 PSP50 PSP119 PSP62 PSP119
20
PSP62 PSP119 PSP85 PSP85 (2) PSP85 PSP85 (2)
30
PSP85 PSP85 (2) PSP119 PSP119 (2) PSP119 PSP119 (2)
50
PSP62 +
PSP85
PSP119 (2) + PSP62
PSP85 (2)
PSP119 (3)
PSP119 (2)
PSP119 (4)
Note: Drawdown will be affected by operating temperature of the system, accuracy of the pressure switch and gauge, the actual precharge pressure, and rate of fill. Pumps installed with a Pro-source® PLUS tank require a relief valve equal to the tank's maximum operating pressure. Relief valve must be capable of relieving entire flow of pump at relief pressure.
CHART B
Drawdown Volume Multiplier* (Approx.)
Pump Off
PUMP START PRESSURE PSI
Pressure
PSI
10 20 30 40 50 60 70 80
20
0.26
30
0.41 0.22
40
0.37 0.18
50
0.46 0.31 0.15
60
0.40 0.27 0.13
70
0.47 0.35 0.24 0.12
80
0.42 0.32 0.21 0.11
90
0.48 0.38 0.29 0.19 0.10
100
0.44 0.35 0.26 0.17
*Utilize this chart if proper selection cannot be made using Chart A. Drawdown based on Boyle's Law.
Procedure: 1. Identify drawdown multiplier relating to specific application.
2. Insert multiplier (X) into the following formula:
Pump GPM x Min Runtime =
Minimum Tank
Multiplier (X)
Capacity Required
Example:
An example of a 20 GPM pump with a minimum runtime of 1 minute, installed on a 50-70 PSIG system pressure range:
20 GPM x 1 minute
83.3 minimum U.S. gal.
= .24 (factor) from Chart B
tank capacity required
Referring to "Ordering Information" chart, the model PSP85-T52 has the closest U.S. gallon capacity that is greater or equal to the minimum volume requirement of 83.3 U.S. gallons.
69
M9133WS
tanks
PRO-SOURCE® Plus Premium Steel Pressurized
OPERATING CYCLE
1. S eparator is completely empty: A new cycle is ready to begin. Simple, positive action produces maximum drawdown on every cycle.
2. W ater begins to enter the tank: Air is compressed around the water separator as it fills with water.
3. P ump-up cycle completed: Air is now compressed to the cut-off setting of pressure switch.
4. Water is being drawn from the tank: Compressed air in the tank forces water out of the separator.
OUTLINE DIMENSIONS
A
E D
Catalog Number
Discharge
NPT
A
B
C
D
E
F
PSP19T-T02
1"
16.1 15.5 2.0 27.8
3.9
PSP19S-T02
1"
20.1 15.5 2.0 21.5
2.3
PSP32-T02
1"
16.1 15.5 2.0 43.0
2.3
PSP35-T05
1"
20.1 15.5 2.0 33.0
2.3
PSP50-T50
1-1/4"
24.1 22.7 2.5 33.2
5.5
PSP62-T51
1-1/4"
24.1 22.7 2.5 40.1
5.5
PSP85-T52
1-1/4"
24.1 22.7 2.5 51.5
5.5
PSP119-TR50
1-1/4"
24.1 22.7 2.5 68.6
5.5
Dimensions (in inches) are for estimating purposes only.
C F B
70
M9133WS
tanks
PRO-SOURCE® Plus Steel Pressurized
APPLICATIONS Use wherever pressurized tanks are needed in water systems applications.
SPECIFICATIONS Shell: Heavy-gauge steel Base: High-impact composite, ABS Finish: Electrostatically applied, baked-on polyester paint Water Cell: One-piece seamless PVC, made from FDA listed material Flange: Reinforced polypropylene Service Connection: Reinforced polypropylene integral to flange Air Valve: Rubber stem/brass body Schrader valve assembly UV Valve Cover: High-density polyethylene
PS119 PS62
PS32 PS50
PS85
PS6 PS35
PS19T
PS19S
PS5
PS19H
PS6H
PS2
ORDERING INFORMATION
Catalog Number
Maximum Capacity Gal/Liter
Diameter* Inch/cm
Height Inch/cm
Length Precharge Inch/cm PSI/kPa
Connection Size
Female
VERTICAL MODELS
PS6-S02
6.0/22.7
12/30.5
16.1/40.9
40/276
3/4" NPT
PS19S-T02
19/72
20/40.6
21/53.3
40/276
1" NPT
PS19T-T02
19/72
16/40.6
27.5/70
40/276
1" NPT
PS32-T03
32/122
20/51
43/109
40/276
1" NPT
PS35-T05
35/133
16/40.6
33/84
40/276
1" NPT
PS50-T50
50/189
20/51
32.5/83
40/276
1-1/4" NPT
PS62-T51
62/235
24/61
39.5/100
40/276
1-1/4" NPT
PS85-T52
85/322
24/61
51/130
40/276
1-1/4" NPT
PS119-TR50 119/450
24/61
68/173
40/276
1-1/4" NPT
IN-LINE VERTICAL MODELS
PS2-S01
2.0/7.6
8.4/21.3
12.6/32.0
20/137.8 3/4" NPTM
PS5-S02
5.0/18.9
10.6/26.9 16.2/41.1
30/206.8 3/4" NPTM
HORIZONTAL MODELS
PS6H-S05
6.0/22.7
12/30.5
13.8/35.0 16/40.6
40/276
3/4" NPT
PS19H-S00
19/72
16/40.6
17.5/44.5 28/71.1
40/276
1" NPT
*Subject to change without notice.
Maximum Operating Pressure = 100 PSI
Maximum Liquid Temperature: 120°F (49°C) Maximum External (Ambient) Temperature: 125°F (52°C)
Drawdown in Gallons/Liter
20-40
30-50
40-60
2.2/8.3 6.9/26.1 6.9/26.1 11.6/43.9 12.7/48.1 18.3/69.3 21.4/81.0 30/113.6 41.3/156.3
1.8/6.8 5.8/21.9 5.8/21.9 9.8/37.1 10.7/40.5 15.5/58.7 18.3/69.3 26/98.4 35.4/134.0
1.6/6.0 5.0/18.9 5.0/18.9 8.5/32.2 9.3/35.2 13.4/50.7 16.0/60.6 22/83.3 31.0/117.3
0.7/2.65 2.2/8.3
0.6 /2.2 1.8/6.8
NA 1.8/6.8
2.2/8.3 6.9/26.1
1.8/6.8 5.8/21.9
1.6/6.0 5.0/18.9
Weight lbs/kg
18/8.2 45/20.4 40/18.1 56/25.4 66/29.9 84/38.1 112/50.8 124/56.2 140/63.5
12.6/5.7 16.2/7.3
22/10 40/18
71
M9134WS
tanks
PRO-SOURCE® Plus Steel Pressurized
FEATURES
Heavy-Gauge Metal Construction: Sturdy "welded wrapper and head design." Built to last.
Polyester Paint Finish: Electrostatically powder-painted, then oven-baked for a smooth high-gloss, appliance-quality finish. Resists corrosion.
Elongated, Seamless Water Cell: n Controlled 2-dimensional cell expansion.
n Rugged, seamless "water cell" prevents the most common cause of tank failure "waterlogging."
n Water never touches the steel tank material.
n Translucent bag material facilitates manufacturing quality control inspection.
Composite Sealing Flange: nCorrosion-resistant.
n Integral O-ring groove better traps the water cell's sealing ring.
n Reinforcing ribs strengthen and maintain a flat smooth sealing surface.
Integral Standpipe: Keeps the water cell standing erect, promoting complete flushing of the water entering/exiting the tank.
Nitrogen-Rich Precharge: Decreases air permeation three to four times over straight air precharge.
40 PSI Precharge: Ready for use with 40/60 pressure range systems. Enables installer to reduce pressure depending on pressure switch setting.
Sturdy Base: Tested-tough composite construction.
Tank Sizing Rule
Size tank for one gallon of drawdown for each gallon per minute at pump capacity.
Example: For a 1 HP, 20 GPM unit pumping 20 gallons per minute on a 30-50 pressure switch setting, the properly sized Pro-Source® tank is a PS85-T52 which has a 26 gallon drawdown.
CHART A
Tank Selection Chart
Pump GPM
SYSTEM PRESSURE SWITCH SETTING PSI
20-40
30-50
40-60
Runtimes
1 Minute 2 Minute 1 Minute 2 Minute 1 Minute 2 Minute
5
PS19T PS32 PS19T PS35 PS19T PS50
7.5
PS32
PS50
PS32
PS50
PS32
PS62
10
PS32
PS62
PS35
PS85
PS50
PS85
12.5 PS35
PS85
PS50
PS85
PS50 PS119
15
PS50
PS85
PS50 PS119 PS62 PS119
20
PS62 PS119 PS85 PS85 (2) PS85 PS85 (2)
PS119
30
PS85 PS85 (2) PS119
+
PS119 PS119 (2)
PS85
30
PS119
PS119
+
PS119 PS119 (2)
PS85
PS62
PS85 PS119 (3)
50
+
PS85 (3) PS85 (2) PS119 (3)
+
+
PS85
PS119 PS50
Note: Drawdown will be affected by operating temperature of the system, accuracy of the pressure switch and gauge, the actual precharge pressure, and rate of fill. Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
CHART B
Drawdown Volume Multiplier* (Approx.)
Pump Off
PUMP START PRESSURE PSI
Pressure
PSI
10 20 30 40 50 60 70 80
20
0.26
30
0.41 0.22
40
0.37 0.18
50
0.46 0.31 0.15
60
0.40 0.27 0.13
70
0.47 0.35 0.24 0.12
80
0.42 0.32 0.21 0.11
90
0.48 0.38 0.29 0.19 0.10
100
0.44 0.35 0.26 0.17
*Utilize this chart if proper selection cannot be made using Chart A. Drawdown based on Boyle's Law.
Procedure: 1. Identify drawdown multiplier relating to specific application.
2. Insert multiplier (X) into the following formula:
Pump GPM x Min Runtime =
Minimum Tank
Multiplier (X)
Capacity Required
Example:
An example of a 20 GPM pump with a minimum runtime of 1 minute, installed on a 50-70 PSIG system pressure range:
20 GPM x 1 minute
83.3 minimum U.S. gal.
.24 (factor) from Chart B = tank capacity required
Referring to "Ordering Information" chart, the model PS85-T52 has the closest U.S. gallon capacity that is greater or equal to the minimum volume requirement of 83.3 U.S. gallons.
72
M9134WS
tanks
PRO-SOURCE® Plus Steel Pressurized
OPERATING CYCLE
1. S eparator is completely empty: 2. Water begins to enter the tank: Air
A new cycle is ready to begin.
is compressed around the water
Simple, positive action produces
separator as it fills with water.
maximum drawdown on every cycle.
3. Pump-up cycle completed: Air is now compressed to the cut-off setting of pressure switch.
ACCESSORIES
4. Water is being drawn from the tank: Compressed air in the tank forces water out of the separator.
PKG 198 Universal Jet Pump to Tank Bracket
PKG 111, PKG 112 or PKG 207 Jet Pump-to-Tank Mounting Pkg.
Ordering Information
PKG 198 - Jet Pump Mounting Bracket PKG 111 - Pump-to-Tank Fitting Package for composite jet pumps PKG 112 - Pump-to-Tank Fitting Package for cast iron series jet pumps with composite fittings PKG 207 - Pump-to-Tank Fitting Package for cast iron series jet pumps with galvanized fittings
MULTIPLE TANK INSTALLATIONS
Pro-Source® tanks can be connected together to increase the supply of usable water (drawdown). Two tanks of the same size will double the supply and three tanks will triple the supply. See Figures No. 1 and 2 for the typical installations of this kind.
TANKS
TANKS
FROM WELL
PRESSURE SWITCH
Figure 1
TO SERVICE PIPING
LSTA-CON3
FROM WELL
PRESSURE SWITCH
Figure 2
73
LSTA-CON4
TO SERVICE PIPING
M9134WS
B
tanks
PRO-SOURCE® Plus Steel Pressurized
OUTLINE DIMENSIONS
B
16" CONFIGURATION
30 E
16" CONFIGURATION
30° E
F
12" CONFIGURATION A
D A
C D
IN-LINE VERTICAL MODELS
Catalog Number Discharge NPT
A
VERTICAL MODELS
PS6-S02
3/4"
12.0
PS19T-T02
1"
16.1
PS32-T03
1"
16.1
PS19S-T02
1"
20.1
PS35-T05
1"
20.1
PS50-T50
1-1/4"
24.1
PS62-T51
1-1/4"
24.1
PS85-T52
1-1/4"
24.1
PS119-TR50
1-1/4"
24.1
IN-LINE VERTICAL MODELS
PS2-S01
3/4"
18.4
PS5-S02
3/4"
10.6
HORIZONTAL MODELS
PS6H
3/4"
12.1
PS19H
1"
16.2
Dimensions (in inches) are for estimating purposes only.
B
C
15.5
2.0
15.5
2.0
15.5
2.0
15.5
2.0
22.7
2.5
22.7
2.5
22.7
2.5
22.7
2.5
16.9
6.9
26.6
8.7
74
F 12" CONFIGURATION
D A
A
C
E D
F B
D
C
E
16.1
27.8
43.0
21.5
33.0
33.2
40.1
51.5
68.6
12.6
16.2
10.0
13.3
12.5
17.5
F
3.9 2.3 2.3 2.3 5.5 5.5 5.5 5.5
6.1 13.8
M9134WS
tanks
PRO-SOURCE® Plus Steel Pressurized
SEQUENCE OF OPERATION
WATER CELL IS COMPLETELY EMPTY: A new cycle is ready to begin. Simple, positive action produces maximum drawdown on every cycle.
WATER BEGINS TO ENTER THE TANK: Air is compressed around the water cell as it fills with water.
PUMP-UP CYCLE COMPLETED: Air is now compressed to the cut-off setting of pressure switch.
WATER IS BEING DRAWN FROM THE TANK: Compressed air in the tank forces water out of the water cell.
75
M9134WS
tanks
PRO-SOURCE® Plus Steel Pressurized Steel EpoxyLined
Air-over-water tanks
The Pro-Source® EpoxyLined Tank is an excellent corrosionresistant tank available in a variety of sizes for use in water systems applications, as a retention tank or holding tank. This tank utilizes an electrostatic paint process, resulting in superior rust protection.
APPLICATIONS
n For use as a standard water tank, retention tank or holding tank.
SPECIFICATIONS
Shell Heavy gauge steel
Skirt Heavy gauge steel
Interior Coating Epoxy
Fittings Machined steel
Finish Baked-on polyester paint
FEATURES Quality Construction The precision press fit head and wrapper minimize the possibility of large gaps between components. This manufacturing process reduces the possibility of corrosion and seam leaks.
Heavy Gauge Steel Sturdy construction is emphasized, with heavier gauge steel than most tanks. This minimizes the possibility of dents from mishandling, and rust-through.
Uniform Epoxy Coating The insides of the tanks are electrostatically powder-coated and then are oven baked to ensure proper adhesion and consistent coverage. This paint process offers superior corrosion resistance over traditional wet paints.
Appliance-like Exterior Finish A polyester paint is also electrostatically adhered to the outer surface and then baked on for a high-gloss appearance.
Flush Mount Fittings Designed to solve one of the toughest corrosion problems, these fittings eliminate flanges and sharp angles that make paint adherence difficult.
Standard Top Mount Fitting Facilitates use as a retention tank, or for hard-to-fit areas. This fitting can also be used for an optional jet mount package.
Sturdy Base Bases for horizontal models are constructed of heavy gauge steel, with slots for ventilation to avoid condensation problems.
ORDERING INFORMATION
Catalog Number
AW30H AW42 AW42T AW85 AW120
Capacity U.S. Gal.
30 42 42 85 120
Style
Horizontal Vertical Vertical Vertical Vertical
Tank Diameter
16" 20" 16" 24" 24"
Tank Height
17-1/2" 36-5/8" 53-1/2"
51" 68"
Tank Length
36-1/2" N/A N/A N/A N/A
Approx. Wt. Lbs.
55 67 65 94 120
Max. Oper. Press. (PSI)
75 75 75 75 75
In order to provide the best products possible, specifications are subject to change.
76
M10374WS
H
C
tanks
PRO-SOURCE® Plus Steel PressurizBed Steel EpoxyLined
A
G
VERTICAL OUTLINE DIMENSIONS
HORIZONTAL OUTLINE DIMENSIONS
A
D
F
E
1-1/4 NPT
B
C
L
H
C
H
B
A
G
Dimensions (in inches) are for estimating purposes only.
Dimensions (in inches) are for estimating purposes only.
DIMENSIONAL DATA A
Vertical EpoxyLined Tanks
Catalog Number
AW42
Gallons 4E2
D Dia. 20
AW42T AW85
42
16
B
85
24
AW120
120
24
Horizontal EpoxyLined Tanks
Catalog
Number
Gallons
Dia.
AW30H
30
16
H Ht. 36-5/8 53-1/2
C
L51 68
A Dist. 8-1/2
8 12 12
FA Size 1-1/4 1-1/4 1-1/4 1-1/4
Dimensions in Inches
B Dist.
B Size
19-1/2
1-1/4
28
1-1/4
26-1/8
1-1/4
35
1-1/4
C Dist. 27-3/4
45 40-7/8 58-1/8
C Size 1/4 1/4 1/4 1/4
G Dist. 8-1/2
8 9-1/2 9-1/2
G Size 1-1/4 1-1/4 1-1/4 1-1/4
Dimensions in Inches
H
Length
Ht.
A
B
C
36-1/2
17-1/2
13-3/4
4-3/4
22
Outlet Size
E
F
3/4
1/4
Horizontal tanks include pump mounting bracket as standard.
Note: All pumps installed with a Pro-Source® tank require a 75 PSI relief valve. Relief valve must be capable of relieving entire pump flow at relief pressure.
TANK PERFORMANCE
Catalog Number
AW30H AW42 AW42T AW85 AW120
Capacity U.S. Gal.
30 42 42 85 120
Drawdown in Gallons
20-40
5.2 6.7 6.9 14.3 19.9
30-50
4.4 5.8 5.9 12.3 17.1
40-60
3.9 5.0 5.2 10.7 14.9
U238-5 Air Volume Controls
(Jet pump type)
E238-2 Air Volume Control (Submersible type)
77
M10374WS
centrifugal pumps
Quick Prime Self-Priming
The Quick Prime self-priming centrifugal pump is designed for demanding jobs where a lot of water is required over a long period of time. For lawn and garden sprinkling, car washing, or other big cleaning and maintenance jobs, it's built for one purpose only continuous high performance service. Not for use with corrosive chemicals or flammable liquids.
APPLICATIONS
n Water systems... lawn and gardening sprinkling, car washing, or other big cleaning and maintenance jobs
SPECIFICATIONS n High tensile gray iron pump case
and motor bracket n Square rubber sealing rings n Proven thermoset diffuser n Engineered composite impeller n Carbon/ceramic shaft seal
FEATURES
Ruggedly Built To meet the demands for long, hard continuous service without over-working or overloading the motor.
Manufactured To precise performance specifications.
Impellers Corrosion resistant for long life.
Simply Design Powerful, efficient operation and easy servicing.
Proper Impeller Alignment For smooth, quiet running.
Unique Diffuser Design For quick automatic prime. No additional water needed for repriming after installation.
Common Brackets Cases and gaskets on all sizes... simplified parts selection.
ORDERING INFORMATION
Catalog Number
1 Phase
3 Phase
QP7
QP7-3
QP10
QP10-3
QP15
QP15-3
QP20
QP20-3
QP30
QP30-3
HP
3/4 1 1-1/2 2 3
Pipe Sizes
Suct.
Disch.
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
Maximum Total Shut-Off Hd.
Feet
PSI
105
45.5
108
47
111
48
116
50
121
52
1 and 3 Ø Approx. Wt. Lbs.
58 61 68 74 87
78
M9136WS
centrifugal pumps
Quick Prime Self-Priming
1-1/2 NPT
OUTLINE DIMENSIONS
PUMP PERFORMANCE
1-1/2 NPT
Catalog Number 1 Phase 3 Phase HP
Disch. Pressure
PSI
Capacity in GPM for Discharge Pressure and Total SuctionLift
Indicated
10 Ft. 15 Ft. 20 Ft. 25 Ft.
20
40.75 38.1 36.1 33.2
25
35.75 33.5 30.9 27.5
5-3/4 A
Cat. No. A
QP7 16.75
QP10 16.75
QP15 18.625
5-3/4 A
QP20 18.625 QP30 21.625
QP7 QP7-3 3/4
30
30.75 27.25 23.1
18
35
21.5 15.1
8.5
40
6.5
20
51.2 48.9 46.4 39.25
25
46.2 43.5 40.6 37.4
QP10 QP10-3 1
30
40.5 37.5 33.6 29.2
35
33
27.6 20.6
10
40
19
5
20
71.6 69.4 63.4 50.25
1-1/2 NPT
25
QP15 QP15-3 1-1/2
30
66.5 62.5 58.75 50.25
59.5
55
50.5
45
35
50.5 43.6
37
24.9
9-7/8
1-1/2 NPT
40
36.8 25.9
20
78.9 76.6 70.5 55.5
25
74.6 71.5
67
55.5
7-27/32
R
QP20 QP20-3 2
30
68.5 63.5 58.4
53
35
58.5 52.9
47
40
9-7/8 5-1/4 9-1/2
7-27/32
Dimensions (in inches) are for estimating purposes only.
PUMP PERFORMANCE
Capacity liters per minute
0
100
200
300
400
40
47.5 40.5 32.5
20
93
91
82
64
25
92.9
91
82
64
R
30
89.8 85.5 78.6
64
QP30 QP30-3 3
35
81
73.3 65.6
57
5-1/4
40
67.9 59.1 48.5 37.5
45
47.9
30
9-1/2 NOTE: S ingle phase units are dual voltage (115/230 volt) 2 and
3 HP are 230 volt only.
NOTE: All units are loaded within the motor service factor and are rated for continuous operation.
Total head in feet Total head in meters
120
36
100 80
3/4 HP
1-1/2 1 HP
H2PH3 PHP
25'
25'
25'
25'
25'
20'
20'
32 28 24
20'
20'
15' 15'
20
60
15'
20'
16
15'
40
15' 10'
12
10'
8 20
4
0 0 10 20 30 40 50 60 70 80 90 100 110
Capacity gallons per minute
79
M9136WS
centrifugal pumps
Quick Prime Self-Priming
Myers® powerful high head 5 HP self-priming pump delivers strong dependable performance for the most demanding jobs. The heavy duty 84JM motor, brass impeller, and large capacity rugged cast iron pump end deliver reliable and continuous high performance service.
APPLICATIONS
n Industrial/commercial applications requiring large flow rates... sprinkler systems; irrigation; booster service; water transfer, circulation and supply; dewatering, fire protection
SPECIFICATIONS
n High tensile cast iron pump case and motor bracket
n Brass impeller
n Ceramic/glass composite diffuser with stainless steel wear ring
FEATURES
Powerful Performance Maximum head of 178 feet (77 psi) and flow capabilities to 135 gpm
Heavy Duty Motor Full frame 184JM design, extra large, double-ball bearings, non-overloading, continuous duty rating, strong capacitor start, single or three phase options
Brass Impellers Precision machines and balanced for smooth, quiet operation
Quick Priming Large case for maximum water retention to insure quick and easy priming, true self-priming design with top suction inlet retains water in case and maintains the prime, exclusive diffuser plate with stainless steel impeller wear ring for fast priming
Mechanical Shaft Seal Precision lapped and polished carbon/ceramic faces, Buna elastomers, and stainless steel metal components, top suction pump design prevents the seal from running dry
Easy Serviceability Convenient back pull-out design
ORDERING INFORMATION
Catalog Number
Pipe Sizes
Suct.
Disch.
QP50B
2-1/2"
2"
QP50B-3
2-1/2"
2"
Motor Voltage
230 207/230/460
Phase 1 3
Max. Amps 29.0
13.4/13.2/6.6
NOTE: T his table is based on copper wire. If aluminum wire is used it must be two sizes larger. Example: When the table calls for #12 copper wire you would use #10 aluminum wire.
Approx. Wt. Lbs.
58 61
80
M9137WS
centrifugal pumps
Quick Prime Self-Priming
OUTLINE DIMENSIONS 24 3-25/32
1 9-53/64
14-15/16 6-1/2
3-1/4 .25 R Slots
2" NPT Discharge 2-1/2" NPT Suction 12-7/64
5-13/16
9-3/8
1/4" NPT Drain Plug
1-1/8" Conduit Hole
11-5/8 14-5/16
5-7/8
Dimensions (in inches) are for estimating purposes only.
PUMP PERFORMANCE
0 180 160 140 120 100
80 60 40 20
0
Capacity liters per minute
100
200
300
400
500
50
25
20
5 HP
40
15
30 10
5
20
10
20
40
60
80 100 120
Capacity gallons per minute
0 140
PUMP PERFORMANCE
Total Suct.
Discharge Pressure (GPM)
Max.
Pipe Size
in Feet 10 psi 20 psi 30 psi 40 psi 50 psi Pressure (psi) Suct. Disch.
0
126 120 104
77
5
125 123 113 107 98
75
10
110 108 107 103 88
72
2-1/2 2
15
91 90 88 84 80
70
20
67 65 63 62 40
63
CABLESELECTION
Motor Rating
Voltage Phase 14 12
230
1
207
3
230
3
130
460
3 330 530
Copper Wire Size 10 8 6 4 2 0
150 250 400 625 1000 160 250 400 640 1020 1630 210 340 540 850 1360 2160 850 1350 2150 3422 5440 8650
This table is based on copper wire.If aluminum wire is used it must be two sizes larger. Example: When the table call for #12 copper wire you would use #10 aluminum wire.
Total head in feet Total head in meters
81
M9137WS
centrifugal pumps
QP Series Field Assembly Kits
These kits provide many quality features and capabilities to meet a wide range of application with 1 - 5 HP, heads to 180 Feet and capacities to 135 GPM.
ORDERING INFORMATION
Catalog Number
HP
QP10KIT QP15KIT
1 1-1/2
QP20KIT
2
QP30KIT
3
QP50KIT
5
Impeller Composite
Brass
82
M9138WS
centrifugal pumps
PQP Series
Quick priming PQP Series Pumps feature lightweight construction in a self-priming design. These models offer a stronger pump body with reinforcement ribs and also a new 2" suction that is designed for the professional pump contractor.
APPLICATIONS n Turf sprinkling and water transfer...
for residential and light commercial
SPECIFICATIONS Pump Body Fiberglass-reinforced engineered composite
Base High-impact composite
Seal Plate Fiberglass-reinforced engineered composite
Impeller Polycarbonate
Diffuser Polycarbonate
Shaft Stainless steel
Clamp Stainless steel
FEATURES
n 1, 1-1/2, 2 and 2-1/2 HP
n Single Phase 115/230V dual voltage, 60 Hz; ODP
n Fiberglass-reinforced Polypropylene Pump Body and Seal Plate Lightweight, corrosion-resistant and exceptionally strong
n Drain Port Provided for easy winterization
n Corrosion-resistant Composite Pump Base
n Easy Serviceable Back Pullout Design
n 2-Compartment, Square Flange Motor, Thermal Overload Protected
n Rapid Priming Once pump body is filled with water
ORDERING INFORMATION
Catalog Number PQP10 PQP15 PQP20 PQP25
HP 1 1-1/2 2 2-1/2
Pipe Tapping Sizes
Suction
Discharge
1-1/2" 1-1/2"
2" 2"
1-1/2" 1-1/2"
2" 2"
Motor Voltage 115/230 115/230 230 230
Approx. Wt. Lbs. 38 41 52 54
83
M9140WS
centrifugal pumps
PQP Series
OUTLINE DIMENSIONS
A E
1/2 NPT Pipe Plug
Suction
F Discharge
D C
1/4 NPT Drain
Dimensions (in inches) are for estimating purposes only.
Cat. No. A
C
D
E
F
PQP10 17.58 9.71 11.82 2.52 10.18
PQP15 18.46 9.71 11.82 2.52 10.18
PQP20 20.0 8.88 12.38 3.81 11.18
PQP25 20.5 8.88 12.38 3.81 11.18
PUMP PERFORMANCE Capacity in Gallons Per Minute
PQP10
PQP15
PQP20
PQP25
Disch. Press.
PSI
Distance Above Water 5' 10' 15' 20' 25' 5' 10' 15' 20' 25' 5' 10' 15' 20' 25' 5' 10' 15' 20' 25'
Capacity Gallons per Minute
10
53 52 50 48 46 67 66 64 61 59 70 69 67 64 62 90 88 86 82 80
20
45 42 39 37 35 59 56 54 50 47 61 59 56 53 50 79 76 72 70 65
30
35 31 27 24 18 48 44 40 37 32 50 48 44 41 37 66 62 57 55 50
40
17 10
31 26 20 10
36 33 25 23 19 50 45 42 37 32
50
16 9
30 23 20
Total head in feet Total head in meters
PUMP PERFORMANCE
0 150
Capacity liters per minute
50 100 150 200 250 300 350
40 125
100
30
75
2-1/2 HP
20
50
2 HP 1-1/2 HP
1 HP
10 25
0
0
20
40
60
80
100
Capacity gallons per minute
84
M9140WS
centrifugal pumps
CT Series-Crusader
Crusader centrifugal pumps are designed to meet your toughest pumping requirements. Rugged cast iron construction can be coupled with either a corrosion resistant composite, or a lead-free brass impeller. Versatile design features allow Crusader pumps to be installed with either a vertical or horizontal discharge. The CT Series is ideal for irrigation, air conditioning, cooling tower and booster applications.
APPLICATIONS
n Booster service, irrigation, circulating, cooling towers, air conditioning, liquid transfer, sprinkling systems, general industrial service, OEM equipment
SPECIFICATIONS
Seal Plate Heavy-duty cast iron
W ear Ring Impeller Reinforced composite with stainless steel
Standard Casing Heavy-duty cast iron
Mechanical Seal Carbon ceramic faces
FEATURES n 1/2 to 2-1/2 HP models n High Head Capabilities to 140 Feet n Flow Capacities to 95 GPM n Double Ball-bearing Motor n Continuous-duty Rated n Single Phase (115/230V) n Three Phase (208/230/460V)
n Choice of Impellers Composite impeller rated to 140°F, Brass impeller rated to 212°F
n Maximum Working Pressure of 125 PSI
n Choice of Complete Unit or Pump End Assembly
ORDERING INFORMATION
Catalog Number
Composite Impeller
Brass Impeller
115-230 Volt
208/230/460 Volt
1 Phase 3 Phase 1 Phase
3 Phase
CT05 CT053
CT05B
CT05B3
CT07 CT073
CT07B
CT07B3
CT10 CT103
CT10B
CT10B3
CT15 CT153
CT15B
CT15B3
CT20 CT203
CT20B
CT20B3
CT25 CT253
CT25B
CT25B3
Capacity in U.S Gallons per Minute Total Head in Feet
HP WT (lb/kg) 50 60
70
80
90 100 110
1/2
39/18 23 18
12
3/4
42/19 35 29
23
15
1
43/20 44 39
34
27
1-1/2
54/25
51
46
42
36
28
2 2-1/2
66/30 74/34
62
54
45
35
70
63
57
48
41
Pipe Size
Suction Discharge
1-1/4" 1-1/4" 1-1/4" 1-1/4" 1-1/2"
2"
1" 1" 1" 1" 1-1/4" 1-1/2"
85
M9141WS
centrifugal pumps
CT Series-Crusader
OUTLINE DIMENSIONS
A
F
Discharge
Suction E
D C
7/16 Dia. (4) Holes
2.00
B
HP
A
B
C
D
E
F
1/2
13.88
5.5
4.38
7.25
9.0
8.0
3/4
14.63
5.5
4.38
7.25
9.0
8.0
1
15.13
5.5
4.38
7.25
9.0
8.0
Dimensions (in inches) are for estimating purposes only.
PUMP PERFORMANCE
0 150
Capacity liters per minute
50 100 150 200 250 300 350
125
2-1/2 HP
40
2 HP
100
30
Total head in feet Total head in meters
1-1/2 HP
1
HP 3/4
HP 1/2
75 20
50
10 25
HP
0
0
20
40
60
80
100
Capacity gallons per minute
Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Pumps with a conventional tank require a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
2.50
2.50
3.50
HP
A
B
C
D
E
F
1-1/2 15.125 5.5
4.8
7.25
9.0
8.0
2
16.50 6.25
4.5
7.5
9.5
8.88
2-1/2 16.50 6.25
4.5
7.5
9.5
8.88
Discharge Pressure
Dynamic Suction Lift
Feet HP PSI Head 5'
10'
15'
20'
25'
10
23.1
--
34
32
29
26
1/2
20
46.2
25
21
18
15
11
30
69.3
10
--
--
--
--
10
23.1
--
--
42
39
37
3/4
20
46.2
35
32
30
28
26
30
69.3
24
22
19
15
10
20
46.2
48
46
45
43
40
1
30
69.3
38
35
31
28
25
40
92.4
23
20
15
--
--
20
46.2
62
60
58
55
52
1-1/2 30
69.3
50
48
44
40
37
40
92.4
37
32
29
22
--
20
46.2
71
68
66
62
60
30
69.3
60
57
52
59
45
2
40
92.4
45
40
36
31
24
50 115.5 22
15
--
--
--
20
46.2
81
79
76
74
71
30
69.3
69
67
63
60
56
2-1/2
40
92.4
56
51
47
44
38
50 115.5 33
30
22
15
--
86
M9141WS
centrifugal pumps
Centri-Thrift
The Myers® Centri-Thrift centrifugal pumps are designed for continuous service under demanding conditions. Centri-Thrift pumps have earned a reputation for reliability.
APPLICATIONS
n Booster service, irrigation, cooling towers, air conditioning, liquid transfer, sprinkling systems, general industrial service, refrigeration, cold and hot water circulation, laundry equipment, building services, spray equipment
SPECIFICATIONS Impeller Bronze Shaft Seal Ceramic seat, carbon washer, stainless steel springs, brass metal parts Volute Case High tensile gray iron Bracket High tensile gray iron
FEATURES n 2 to 7-1/2 HP Models n High Head Capabilities to 140 Feet
n Flow Capacities to 240 GPM
n Available with 1-1/4", 1-1/2" and 2" Discharge Sizes
n Close-coupled or Belt-driven
n Choice of Complete Unit or Pump End Assembly
ORDERING INFORMATION
Catalog Number 125M 150M
200M
HP
2 2 3 3 2 2 3 3 5 5 3 3 5 5 7-1/2
Pipe Tapping Sizes
Suction
Discharge
1-1/2" 1-1/2" 1-1/2" 1-1/2"
2" 2" 2" 2" 2" 2" 2-1/2" 2-1/2" 2-1/2" 2-1/2" 2-1/2"
1-1/4" 1-1/4" 1-1/4" 1-1/4" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2"
2" 2" 2" 2" 2"
Phase
1 3 1 3 1 3 1 3 1 3 1 3 1 3 3
Approx. Wt. Lbs.
78 78 80 80 80 80 81 81 173 173 83 83 175 175 156
87
M9142WS
centrifugal pumps
Centri-Thrift
OUTLINEDIMENSIONS
DISCHARGE
J
SUCTION
D
F
E
C
B
A (APPROX.)
K-(2) SLOTS
G
G
H
125M-150M-200M Series 2 and 3 HP
DISCHARGE
SUCTION
D F
E
C
B
A (APPROX.)
G
G
J
H
K-(4) HOLES
Dimensions (in inches) are for estimating purposes only.
150M-200M Series 5 and 7-1/2 HP
Catalog Number
125M
150M
200M
HP
2 2 3 3 2 2 3 3 5 5 3 3 5 5 7-1/2
Phase
1 3 1 3 1 3 1 3 1 3 1 3 1 3 3
A
18-5/8 18-1/16 19-15/16 18-11/16 18-15/16 18-3/8 20-1/4
19 21-13/16 19-15/16 20-3/4 19-1/2 22-5/16 21-7/16 22-1/16
B
3-13/16 3-13/16 3-13/16 3-13/16 4-1/8 4-1/8 4-1/8 4-1/8 11-11/16 11-11/16 4-5/8 4-5/8 12-13/16 12-13/16 12-13/16
C
1-13/16 1-13/16 1-13/16 1-13/16 1-13/16 1-13/16 1-13/16 1-13/16 5-1/2 4-1/2 1-13/16 1-13/16 5-1/2 4-1/2 5-1/2
D
9-3/4 7-3/4 9-3/4 7-3/4 9-3/4 7-3/4 9-3/4 7-3/4 9-3/16 9-3/16 9-3/4 7-3/4 9-3/16 9-3/16 9-3/16
E
4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2
F
9-3/16 9-3/16 9-3/16 9-3/16 9-3/4 9-3/4 9-3/4 9-3/4 9-3/4 9-3/4 9-7/16 9-7/16 9-7/16 9-7/16 9-7/16
G
2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 3-3/4 3-3/4 2-1/2 2-1/2 3-3/4 3-3/4 3-3/4
H
3-5/16 3-5/16 3-5/16 3-5/16 3-5/16 3-5/16 3-5/16 3-5/16 4-1/2 4-1/2 3-5/16 3-5/16 4-1/2 4-1/2 4-1/2
J
8-1/4 8-1/4 8-1/4 8-1/4 8-7/16 8-7/16 8-7/16 8-7/16 8-1/2
7 9-3/16 9-3/16 8-1/2
7 7
K
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 13/32 13/32 1/2 1/2 13/32 13/32 13/32
88
M9142WS
Total head in feet Total head in meters
Total head in feet Total head in meters
centrifugal pumps
Centri-Thrift
PUMP PERFORMANCE 125M
Capacity liters per minute
0
50 100 150 200 250 300 350
150
125
3 HP 5-13/16" Imp.
40
100
1-12/2HHPP55-3-1/8/1"6I"mImp.p.
30
75
20
50
10 25
0
0
20
40
60
80
100
Capacity gallons per minute
PUMP PERFORMANCE 150M
0 150
Capacity liters per minute
100 200 300 400 500 600 700
125 100
75 50
2 HP3H4P-5/855"-1HI/mP8"p.I5m-1p5./16" Imp.
40 30 20
10 25
0
0
40
80
120
160
200
Capacity gallons per minute
PUMP PERFORMANCE 125B
0 150
125
100
Capacity liters per minute
50 100 150 200 250 300 350
3400 RPM
3100 RPM 2800 RPM
5-13/16" Imp.
40
30
75 20
50
1750 RPM
10 25
0
0
20
40
60
80
100
Capacity gallons per minute
PUMP PERFORMANCE 150B
0 150 125 100
75
Capacity liters per minute
100 200 300 400 500 600 700
5-15/16" Imp.
3450 RPM
40
26002R9P00MRPM
30 20
50
1750 RPM
10
25
0
0
40
80
120
160
200
Capacity gallons per minute
Total head in feet Total head in meters
Total head in feet Total head in meters
89
M9142WS
centrifugal pumps
Centri-Thrift
PUMP PERFORMANCE 200M
0 150 125 100
75 50 25
Capacity liters per minute
200
400
600
800
1000
3
HP
7-1/2 HP 5-3/4"
5 HP 5-1/8" Imp. 4-7/16" Imp.
Imp.
40 30 20
10
0
0
40
80 120 160 200 240 280
Capacity gallons per minute
PUMP PERFORMANCE 200B
0 150 125 100
75 50 25
Capacity liters per minute
200
400
600
800
1000
5-3/4" Imp.
3450 RPM
40
3000 RPM
30
2550 RPM
20
1750 RPM
10
0
0
40
80 120 160 200 240 280
Capacity gallons per minute
Total head in feet Total head in meters
Total head in feet Total head in meters
90
M9142WS
Booster pumps
MPB Series Serviceable High Pressure Booster
The MPB Booster Pumps are the most durable booster pump available. The proven SignaSealTM floating impeller design minimizes thrust loads allowing for continuous operation without damage to motor bearings, mechanical seal or pump hydraulic components.
APPLICATIONS
n Car wash, filtration and reverse osmosis, residential, commercial or agricultural pressure washing, booster and spray systems, HVAC, general purpose pumping.
Specifications Max. Inlet Pressure 80 PSI Max. Working Pressure 315 PSI Maximum Limits Prolonged use with liquids above 140° F is not recommended. Discharge MPB Series: cast iron Motor Adapter and Base MPB Series: cast iron Shell 300 series stainless steel Impeller Acetal Diffuser Polycarbonate Shaft 300 series stainless steel O-Rings Buna-N Mechanical Seal Carbon/ceramic, Buna-N
FEATURES
Pump and Motor Shaft Stainless steel for maximum corrosion resistance; one-piece threaded shaft for positive impeller drive.
Peak Performance at Every Stage Staging system uses independent floating impellers for superior sand handling.
Balanced Rotor Die cast under high pressures for uniform performance and greater efficiency; dynamically balanced.
Acetal Impellers Precision-molded for perfect balance... ultra-smooth for highest performance and efficiency.
Precision Molded Diffusers Superior
performance with high resistance to corrosion and abrasion.
Heavy-duty Ball Bearings Shielded, permanently lubricated bearings, extensively tested to ensure extended life and smooth, quiet operation.
Myers: The Proven Leader The industry leader in booster pumps offers solutions in a broad range of commercial and OEM applications.
In order to provide the best products possible, specifications are subject to change.
91
M9143WS
Booster pumps
MPB Series Serviceable High Pressure Booster
ORDERINGINFORMATION
Catalog
Number
GPM
7MPB50
7MPB75
7
7MPB100
10MPB50
10MPB75
10MPB100
10
10MPB150
10MPB200
20MPB100
20MPB150 20
20MPB200
20MPB300
30MPB100
30MPB150 30
30MPB200
30MPB300
HP
1/2 3/4 1 1/2 3/4 1 1-1/2 2 1 1-1/2 2 3 1 1-1/2 2 3
Phase
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Stages
9 12 16 6 8 10 14 16 7 9 11 15 5 6 7 11
*Length and weight are approximate. NOTE: ODP motor is standard, for TEFC motors, contact Customer Service.
Pipe Tapping Sizes
Inlet
Outlet
3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 1" 1" 1" 1" 1-1/4" 1-1/4" 1-1/4" 1-1/4"
3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 1" 1" 1" 1" 1-1/4" 1-1/4" 1-1/4" 1-1/4"
Motor Voltage
115/230 115/230 115/230 115/230 115/230 115/230 115/230 115/230 115/230 115/230 115/230 208-230 115/230 115/230 115/230 208-230
Shipping* Wt. (lbs.)
48 48 51 45 46 50 58 63 49 57 62 59 47 54 57 59
ORDERING INFORMATION ACCESSORIES
Pkg. No.
Description
SUCTION
83
Suction hose 3/4" 150 PSI hose, 6 ft. section with two (2) female hose fittings
85
Two (2) garden hose/NPT adapters 3/4" NPT male to 3/4" garden hose male
96
Vacuum relief valve 1/2" NPT
Approx. Wt. Lbs.
3 3 2
150 PSI RATED* DISCHARGE
84
Discharge hose 3/4" 150 PSI hose, 25 ft. section with male and female garden hose fittings
10
86
High pressure pistol grip nozzle with three (3) nozzles (No. 56, 50 and 49)
2
315 PSI RATED* DISCHARGE
162
25' of 1" ID hose with 3/4" male and female hose fittings 315 PSI rating
15
194
High pressure pistol grip nozzle with three (3) nozzles (No. 56, 50 and 49) rated for 500 PSI
2
*To select proper discharge accessories for your pump, add incoming pressure to pump output pressure, to determine total discharge pressure. Example: Incoming pressure 20 PSI + pump output pressure (HP7C at 0 GPM, 300')
87 PSI = Total 150 PSI at discharge = 150 PSI rated discharge accessories
92
M9143WS
PSI Total head in feet Total head in meters
PSI Total head in feet Total head in meters
Booster pumps
MPB Series Serviceable High Pressure Booster
PUMP PERFORMANCE 7 GPM
0 600 250
Capacity liters per minute
10
20
30
40
50 175
500
150
200
7MPB100 - 1 HP
400 150
300
100
7MPB75 7MPB50
-
3/4 1/2
HP HP
125 100 75
200
50
50 100 25
0
0
0
2
4
6
8
10
12
14
Capacity gallons per minute
PUMP PERFORMANCE 20 GPM
0 600 250
500 200
400 150
300
100 200
50 100
Capacity liters per minute
25
50
75
100
175
20MPB300 - 3 HP
150 125
2200MMPPBB11502000M--1P1-B1H2/2P00H-P2 HP
100 75
50
25
0
0
0
5
10
15
20
25
30
Capacity gallons per minute
PUMP PERFORMANCE 10 GPM
Capacity liters per minute
0
10
20
30
40
50
300
700
600 250
500 200
400 150
300
100 200
50
100
1100MMPPBB11501000M--1P1-B1H2/20P0H-P2 HP 10M10PMBP5B07-51-/23/H4 PHP
60 200 150 100 50
0
0
0
2
4
6
8 10 12 14 16
Capacity gallons per minute
PUMP PERFORMANCE 30 GPM
Capacity liters per minute
0
25 50 75 100 125 150 175
175
400
125
150
350
30MPB300 3 HP
100
300 125
250
30MPB200 2 HP
75
100
30MPB150 1-1/2 HP
200
30MPB100 1 HP
75
50
150
50 100
25
25
50
0
0
0
10
20
30
40
50
Capacity gallons per minute
PSI Total head in feet Total head in meters
PSI Total head in feet Total head in meters
93
M9143WS
Booster pumps
MPB Series Serviceable High Pressure Booster
OUTLINE DIMENSIONS
Catalog
Dimensions in inches
Number
HP
A
B
C
D
7MPB50
1/2
24.60
10.38
15.76
6.88
7MPB75
3/4
27.22
10.38
18.39
7.47
7MPB100
1
32.23
11.88
21.89
8.88
10MPB50 1/2
23.19
11.60
13.13
8.63
10MPB75 3/4
25.31
11.97
14.88
9.00
10MPB100 1
28.12
13.03
16.63
10.06
10MPB150 1-1/2
32.07
13.47
20.14
10.50
10MPB200 2
34.13
13.78
21.89
10.81
20MPB100 1
26.02
11.88
15.68
8.88
20MPB150 1-1/2
29.84
13.47
17.91
10.50
20MPB200 2
32.38
13.78
20.14
10.81
20MPB300 3
36.80
14.05
24.47
11.12
30MPB100 1
25.08
11.88
14.92
8.69
30MPB150 1-1/2
27.26
12.63
16.35
9.44
30MPB200 2
28.49
12.42
17.79
9.47
30MPB300 3
35.86
14.05
23.53
11.12
94
M9143WS
UTILITY PUMPS
MSP Swimming Pool Pumps
Myers® quality line of MSP swimming pool pumps deliver long-lasting reliability for residential pool application. These pumps are constructed with corrosion-resistant materials for extended life.Myers incorporates one of the largest strainer baskets available, a see-through lid with UV light stabilizers, and dual voltage motors available in 3/4, 1 and 1-1/2 HP sizes.
APPLICATIONS
n Residential pool
SPECIFICATIONS
Pump Case Polypropylene
Basket Lid Polypropylene
Impeller Polycarbonate/polyester
Fasteners 304 Stainless Steel
Base Polypropylene
Seal Plate Polypropylene
Strainer Polypropylene
FEATURES
Constructed for Long Life n Seal design puts direct contact
between ceramic and heat sink, and in the pumping fluid
n All positive-sealing O-ring gaskets no cork gaskets
n Base supports motor, pump and strainer
n Three motor sizes meet wide range of pool capacities
Easy to Operate n Drain plugs removable by hand
n See-through lid removes easily, has UV stabilizers to protect from sunlight damage
n Strainer has larger basket than similar designs for more capacity
n 1-1/2" x 2" bushings provided
ORDERING INFORMATION
Catalog Number MSP7 MSP10 MSP15
Required Pump Size 3/4 HP 1 HP 1-1/2 HP
Pool Capacity Up to 22,000 gal. 22,000 - 29,000 gal. 29,000 - 38,000 gal.
95
M9139WS
UTILITY PUMPS
MSP Swimming Pool Pumps
OUTLINEDIMENSIONS
8.75
2" NPT
A 2" NPT
15.375 9.75
Total head in feet Total head in meters
Dimensions (in inches) are for estimating purposes only.
PUMP PERFORMANCE
Capacity liters per minute
0
100
200
300
80
70
1-1/2 HP
60
1 HP
50
400 24 20 16
3/4 HP
40
12
30 8
20
4 10
0 0 10 20 30 40 50 60 70 80 90 110
Capacity gallons per minute
96
Cat. No. A MSP7 23.9 MSP10 23.9 MSP15 24.5
12.25 5.5
M9139WS
UTILITY PUMPS
PRO-SOURCE® Composite Engine-Driven Self-Priming Pump
Lightweight, corrosion resistant, engineered composite pump construction make this enginedriven pump extremely versatile for applications where electrical power is not available.
Powered by a powerful 6-1/2 HP, PowerPro 4-cycle gasoline engine, rated for continuous-duty, equipped with professional-grade features like an automatic low-oil safety cut, manual throttle, choke and shut-off controls.
Securely mounted within a rugged steel framed rollcage, reinforced with steel cross-members, coated for corrosion resistance, equipped with noise dampening, non-slip rubber feet. Suction lift capability of 25 feet.
APPLICATIONS
n Water Transfer and Supply Sprinkler Turf Irrigation; Dewatering; Fire Protection; Agriculture, Light Commercial and Marine
SPECIFICATIONS
Body Reinforced corrosion resistant Thermoplastic
Impeller Polymer
Diffuser Reinforced corrosion resistant Thermoplastic
Seals Viton mechanical
O-rings Viton
Check Valve Viton
Roll Cage Coated steel frame with cross member and stay-in-place (no-slip) rubber feet
Engine 6-1/2 HP
Dimensions 21"H x 17"D x 21"L
Fasteners 300 Grade stainless steel
FEATURES n Rugged Light-Weight Design n Corrosion Resistant Composite
Pump Construction
accessories
Suction Hose Kit Built-in 2" NPTFswivel fitting and 2" NPTMfitting for easy hookup; coil-reinforced wall prevents collapse; includes aluminum suction screen to prevent debris from reaching pump
n Chemical Resistant Viton Seals, O-rings with Stainless Steel Fasteners
n Built-in Check Valve
Discharge Hose Kit Built-in 2" NPTF swivel fitting and 2" NPTM fitting for easy hookup; collapsible for easy roll-up and storage; reinforced wall adds durability
ORDERING INFORMATION
Catalog
Number
HP
Description
EDP55RV
5-1/2 Engine-driven pump w/roll cage
Pipe Tapping Sizes Suction Discharge 2" NPT 2" NPT
ACCESSORIES
Catalog Number FP2735 FP2731
Description 2" x 15' Suction Hose Kit 2" x 25' Discharge Hose Kit
Approx. Wt. Lbs./Kg. 46/20.9
Approx. Wt. Lbs./Kg. 15/6.8 6/2.7
FP2735 Suction Hose Kit
FP2731 Discharge Hose Kit
In order to provide the best products possible, specifications are subject to change. .
97
M10375WS
Total head in feet Total head in meters
UTILITY PUMPS
PRO-SOURCE® Composite Engine-Driven Self-Priming Pump
PUMP PERFORMANCE
0 140 120 100
80 60 40 20
0
Capacity liters per minute
100
200
300
400
500
40
EDP55RV
35
30
25
20
15
10
5
0
20
40
60
80
100
120
140
Capacity gallons per minute
OUTLINE DIMENSIONS
[527] 20.8
[278.0] 11.0
[156] 6.1 [70] 2.8
[527] 20.8
[156] 6.1
[413] 16.3
[165] 6.5
[60.0] 2.4
[156] 6.1
[52] 2.0
Dimensions (in inches) are for estimating purposes only.
98
M10375WS
UTILITY PUMPS
Utility Transfer Pump
MES106
The MES106 pumping system solves water transfer needs by removing water from waterbeds, aquariums, non-draining sinks and water standing on basement floors. Pump constructed of proven materials promotes long pump life. Compact design provides easy hookup, application use and storage when not in use.
APPLICATIONS n Ideal for transferring water,
filling tanks and draining shallow flooded areas
SPECIFICATIONS C apacities 5 GPM, 18.9 LPM Shut-off Head 10', 3.1 m Weight 4 lbs. Liquids Handling Drain water Intermittent Liquid Temp. 104°F, 40°C Motor Air-cooled brush motor Electrical Data 115V, 2A, 1Ø, 60Hz Discharge Standard garden hose Housing Cast aluminum Impeller Buna-N Wear Ring 304 Stainless Steel Power Cord 6'
FEATURES n Up to 5 GPM with 10' Head n Connects to Standard Garden Hose n 115VAC with 6' Power Cord n Removes Standing Water
Down to 1/8" Depth n Weighs Only 4 Pounds n Built-in Carrying Handle
n Includes 6' Suction Hose and Floor Drainer
n To Operate, Just Attach a Standard Hose to Pump Discharge and Plug into Any 115V Outlet
n Air-cooled, High-torque, Non-submersible Motor with Overload Protection
ORDERING INFORMATION
Catalog Number
Volts
Hz
MES106
115
60
GPM
Approx. Wt. Lbs.
5
4
99
M9147WS
ACCESSORIES
PressureSwitches
ORDERING INFORMATION
ELECTRICCONTROLSWITCHES
Cat. No. PS10D4 PS10D5 PS10D6 PS20D4 PS20D5
Part No. 15760A000K 15760A001K 15760A002K 15761A000K 15761A001
Factory Pressure Setting
20-40
30-50
40-60
20-40
30-50
Cut-Off
Minimum
Pressure Differential Cut-Off
(Range) Pressure Pressure
Manufacturer's Rating Max. Motor HP
1 PH AC
3 PH AC
DC
Pipe Connection
115V 230V 230V 460V 575V 115/575V NPTF
20-65
10-30
1-1/2 HP 2 HP
3 HP
1/4 HP
1/4"
20-80
10-31
2 HP
3 HP
5 HP
5 HP
5 HP 1/2 HP
1/4"
ELECTRICCONTROLSWITCHES WITHLOWPRESSURECUT-OFF
PS10D4C 19180A000K 20-40
20-65
10-30
10*
1 HP
1 HP
1 HP
PS10D5C 19180A001K 30-50
20-65
10-30
20
1 HP
1 HP
1 HP
PS10D6C 19180A002K 40-60
20-65
10-30
30
1 HP
1 HP
1 HP
1/4 HP
1/4"
1/4 HP
1/4"
1/4 HP
1/4"
All switches are 2-pole.
Code Explanation for Pressure Switch Catalog Numbers
Pressure Switch
Square D
PS stands for Pressure Switch
PS 10 D 4
The number following stands for maximum HP to be used on The next letter stands for the switch manufacturer
1 HP max. motor
20-40 PSI switch setting
The next number stands for the highest pressure of the factory set switch setting
ValvesandRegulators
ORDERING INFORMATION
PRESSURERELIEFVALVES
Catalog No.
Pipe Size
GPM Maximum Minimum Setting Lbs./Sq. In. Regular Setting Lbs./Sq. In. Maximum Setting Lbs./Sq. In. Ship Wt. Lbs.
06430B011K
3/4"
17
25
75
90
1-1/4
EJECTOPRESSUREREGULATORS
Catalog Number
Pipe Size In.
Used On
15495B000K
3/4"
15496B000K
1"
13980A001K
1"
HC33, HC50, HCM50, HCM75 HC75, HC100, HCM100, HCM150, HJA75D, HJA100D, HJ75D, HJ100D
HJA33D, HJA50D, HJ50D, HR50D
AUTOMATICAIRVOLUMECONTROL Deep Well
Vents excess air from tank on all systems which charge tank with air on each operating cycle. Set to prevent air below 30 lbs. tank pressure but adjustable 15 to 40 lbs. Used on deep well ejectors, deep well reciprocating and submersible systems.
Catalog Number 05857A002K
Gauge Taping 1/4"
Tank Connection 1-1/4"
Max. Operating Pressure 65 lbs.
Ship Wt. Oz. 6
100
M9146WS
ACCESSORIES
ValvesandRegulators
ORDERING INFORMATION
AUTOMATICAIRCHARGINGCONTROL
Charges air on each operating cycle. Air is not handed through pump. Copper tube and fitting not included with control for replacement but required in installation. Not recommended for reciprocating pumps.
Catalog Number
NPT
Description
13809A000K 14446A000K
3/8"
82 gallon tanks and smaller
3/8"
Packaged control with tube fittings
AIRVALVES Used with reciprocating, jet and submersible pumps to admit air into system.
Catalog Number
NPT
Used With
05000A000
1/8"
05000A010
1/4"
Water systems Air guard tanks
CHECKVALVES - Vertical or Horizontal
Catalog Number
Part Number
CVA-75 CAP-10 CAP-12 CAP-15 CAPD-20 CAPD-40
26370A001 26370A002K 26370A003K 26370A004K 24429A017 23799A010K
Description
3/4" No-Lead Brass Check Valve 1" No-Lead Brass Check Valve 1-1/4" No-Lead Brass Check Valve 1-1/2" No-Lead Brass Check Valve 2" No-Lead Brass Check Valve 4" No-Lead Brass Check Valve
Pipe Size
3/4" 1" 1-1/4" 1-1/2" 2" 4"
Can Be Used in Pipe Size 1-1/4" 2" 2" 3" 3-1/2" 6"
Ship Wt. Lbs.
1 1-1/4 1-3/4 2-1/4
5 25
VERTICALFOOTVALVES
FVP-75
26369A001K
FVP-10
26369A002K
FVP-12 FVP-15
26369A003K 26369A004
FVP-20
26369A005K
3/4" No-Lead Brass Check Valve 1" No-Lead Brass Check Valve 1-1/4" No-Lead Brass Check Valve 1-1/2" No-Lead Brass Check Valve 2" No-Lead Brass Check Valve
3/4" 1" 1-1/4" 1-1/2" 2"
3/4" 1" 1-1/4" 3" 3-1/2"
3/4 1 1-1/4 2 3
EXTERNALSUBMERSIBLEPUMPCHECKVALVES
Catalog Number
Part Number
CAP-14
24429A012
CAP-16
24429A013K
CAPD-20
24429A017
Description 1" F x 1-1/4" No-Lead Check Valve 1-1/4" F x 1-1/4" No-Lead Check Valve 2" F x 2" M Ductile Iron Check Valve
Ship Wt. Lbs. 2 2
3-1/2
101
M9146WS
ACCESSORIES
WellAdapters, Seals
ORDERING INFORMATION
UNIVERSALWELLADAPTERS For all packer installations. Designed for over-the-well installations with vertical pumps and concentric piping installations with horizontal pumps.
Catalog Number
Part Number
Well Size
Number of Bolts
Drop Pipe
UA2-20
19251C010
2"t
2
1"
UA2-20A
19251C011
2"
2
1-1/4"
90° TYPEWELLADAPTERS
For offset packer installations with horizontal pumps and concentric piping installations with vertical pumps.
Delivery Pipe 1-1/4" 1-1/4"
Pressure Pipe 1-1/4" 1-1/4"
Horizontal Adapter
18021C000K
2"
HA2-20
19253C010
2"
HA2-20A
19253C011
2"
*
1"
1-1/4"
1-1/4"
2
1"
1-1/4"
1-1/4"
2
1-1/4"
1-1/4"
1-1/4"
*No bolts holes inlet and outlet openings are threaded
OPENCENTERCUPLEATHERS
Catalog Number
O.D.
05099A012K
1-13/16"
05099A015K
2"
05099A017K
2-1/2"
05099A019K
3"
SOLIDCENTERCUPLEATHERS
05064A019K
1-5/16"
05064A023K
1-1/2"
Diameter of Hole 1-1/8" 1-5/16" 1-11/16" 1-15/16"
9/16" 9/16"
WATER PRESSURE GAUGE Catalog No. 05003A001K
Description 100 PSI Pressure Gauge
Connection 1/4" NPT 1/4" Bottom Mount
Case Construction Face Diameter Ship Wt. Oz.
Plastic
2"
4
102
M9146WS
GENERAL INFORMATION
Pipe Friction Loss Charts 1/2"-1-1/4" I.D.
Loss of Head in Feet Due to Friction Per 100 Feet of Pipe
1/2"
3/4"
1"
1-1/4"
Flow Velocity Plastic Steel Copper Flow Velocity Plastic Steel Copper Flow Velocity U.S. Gal. Plastic C=140 C=100 C=130 U.S. Gal. Plastic C=140 C=100 C=130 U.S. Gal. Plastic
Min. ft/sec ID .622" ID .622" ID .625" Min. ft/sec ID .824" ID .824" ID .822" Min. ft/sec
Plastic C=140
ID 1.049"
Steel C=100
ID 1.049"
Copper C=130
ID 1.062"
Flow U.S. Gal.
Min.
Velocity Plastic ft/sec
Plastic C=140
ID 1.380"
Steel Copper
C=100 C=130
ID
ID
1.380" 1.368"
0.5 0.5 0.314 0.582 0.35 1.5 0.9 0.61 1.13 0.7 2 0.74 0.322 0.595 0.345 4 0.9 0 .304 0.564 0.364
1 1.1 1.14 2.1 1.26 2 1.2 1.04 1.93 1.21 3 1.1 0.68 1.26 0.732 5 1.1 0.46 0.853 0.545
1.5 1.6 2.38 4.44 2.67 2.5 1.5 1.57 2.91 1.82 4 1.5 1.15 2.14 1.24 6 1.3 0.649 1.2 0.765
2 2.1 4.1 7.57 4.56 3 1.8 2.21 4.08 2.56 5 1.9 1.75 3.42 1.88 7 1.5 0.86 1.59 1.02
2.5 2.6 6.15 11.4 6.88 3.5 2.1 2.93 5.42 3.4 6 2.2 2.45 4.54 2.63 8 1.7 1.1 2.04 1.31
3 3.2 8.65 16 9.66 4 2.4 3.74 6.94 4.36 8 3.0 4.16 7.73 4.5 10 2.1 1.67 3.08 1.98
3.5 3.7 11.5 21.3 12.9 4.5 2.7 4.66 8.63 5.4 10 3.7 6.31 11.7 6.77 12 2.6 2.33 4.31 2.75
4 4.2 14.8 27.3 16.4 5 3.0 5.66 10.5 6.57 12 4.5 8.85 16.4 9.47 14 3.0 3.1 5.73 3.64
4.5 4.8 18.3 33.9 20.4 6 3.6 7.95 14.7 9.22 14 5.2 11.8 21.8 12.6 16 3.4 3.96 7.34 4.68
5 5.3 22.2 41.2 24.8 7 4.2 10.6 19.6 12.2 16 5.9 15.1 27.9 16.2 18 3.9 4.93 9.13 5.81
5.5 5.8 26.6 49.2 29.5 8 4.8 13.5 25 15.7 18 6.7 18.7 34.7 20.1 20 4.3 6 11.1 7.1
6
6.3 31.2 57.8 34.8 9
5.4 16.8 31.1 19.5 20 7.4 22.8 42.1 24.4 25 5.4 9.06 16.8 10.7
6.5 6.9 36.2 67 40.2 10 6.0 20.4 37.8 23.7 22 8.2 27.1 50.2 28.8 30 6.4 12.7 23.5 15 NOTE:Recommended velocity is
7 7.4 41.5 76.8 46.1 11 6.6 24.4 45.1 28.2 24 8.9 31.9 59 5 F3P4S (feet3p5er sec7o.n5d) wi1th6.a9 31.2 20
7.5 7.9 47.2 87.3 52.5 12 7.2 28.6 53 33.2 26 9.7 36.9 68.4 ma3x9i.m7 um o4f07 FPS8. .6 21.6 40 25.6
8 8.4 53 98.3 59.4 13 7.8 33.2 61.5 38.5 28 10.4 42.5 78.5 45.5 50 10.7 32.6 60.4 38.7
8.5 9.0 59.5 110 66 14 8.4 38 70.5 44.2 30 11.1 48.1 89.2 51.6 60 12.9 45.6 84.7 54.1
9 9.5 66 122 73.5 16 9.6 48.6 90.2 56.6 35 13.0 64.3 119 68.7 70 15.0 61.5 114 72.2
9.5 10.0 73 135 81 18 10.8 60.5 112 70.4 40 14.8 82 152 88 80 17.2 77.9 144 92.4
10 10.6 80.5 149 89.4 20 12.0 73.5 136 83.5 45 16.7 102 189 109 90 19.3 96.6 179 115
NOTE: Recommended velocity is 5 FPS (feet per second) with a maximum of 7 FPS.
Friction Losses Through Fittings in Terms of Equivalent Lengths of Pipe
Type Fitting and Application
Pipe and Fitting Material (Note 1)
1/2
Equivalent Length of Pipe Nominal Size Fitting and Pipe
3/4
1
1-1/4
1-1/2
2
Threaded Adapter Plastic or Copper to
Thread
Copper Plastic
1
1
1
1
1
1
3
3
3
3
3
3
Steel
2
3
3
4
4
5
90° Standard Elbow
Copper
2
3
3
4
4
5
Plastic
4
5
6
7
8
9
Insert Coupling
Plastic
3
3
3
3
3
3
Steel
4
5
6
8
9
11
Standard Tee
Copper
4
5
6
8
9
11
Plastic
7
8
9
12
13
17
Gate Valve
Note (2)
2
3
4
5
6
7
2-1/2 1 3 6 6 10 3 14 14 20 8
Note (1) Loss Figures are based on equivalent lengths of indicated pipe material. Note (2) Loss Figures for screwed valves are based on equivalent lengths of steel pipe.
103
GENERAL INFORMATION
Pipe Friction Loss Charts 1-1/2"-2-1/2" I.D.
Loss of Head in Feet Due to Friction Per 100 Feet of Pipe
1-1/2"
2"
Flow U.S. Gal.
Min.
Velocity Plastic ft/sec
Plastic C=140 ID 1.61"
Steel C=100 ID 1.61"
Copper C=130 ID 1.60"
Flow U.S. Gal.
Min.
Velocity Plastic ft/sec
Plastic Steel C=140 C=100 ID 2.067" ID 2.067"
4
0.6
0.144 0.267 0.165
10
1.0
0.233 0.431
6
0.9
0.305 0.565 0.358
15
1.4
0.495 0.916
8
1.3
0.52 0.962 0.611
20
1.9
0.839 1.55
10
1.6
0.785 1.45 0.923
25
2.4
1.27
2.35
12
1.9
1.1
2.04
1.29
30
2.9
1.78
3.29
14
2.2
1.46
2.71
1.71
35
3.3
2.36
4.37
16
2.5
1.87
3.47
2.2
40
3.8
3.03
5.6
18
2.8
2.33
4.31
2.75
45
4.3
3.76
6.96
20
3.2
2.83
5.24
3.31
50
4.8
4.57
8.46
25
3.9
4.26
7.9
5
55
5.3
5.46
10.1
30
4.7
6
11.1
7
60
5.7
6.44
11.9
35
5.5
7.94
14.7
9.35
70
6.7
8.53
15.8
40
6.3
10.2
18.9
12
80
7.6
10.9
20.2
45
7.1
12.63 23.4
14.9
90
8.6
13.6
25.1
50
7.9
15.4
28.5
18.1
100
9.6
16.5
30.5
55
8.7
18.35
34
21.5
110
10.5
19.7
36.4
60
9.5
21.6
40
25.3
120
11.5
23.1
42.7
65
10.2
25.1
46.4
29
130
12.4
26.8
49.6
70
11.0
28.7
53.2
33.8
140
13.4
30.6
56.9
75
11.8
32.6
60.4
38
150
14.3
35
64.7
80
12.6
36.8
68.1
43.1
160
15.3
39.3
72.8
85
13.4
41.2
76.2
47.6
170
16.3
44
81.4
90
14.2
45.7
84.7
53.6
180
17.2
48.9
90.5
95
15.0
50.5
93.6
58.8
190
18.2
54
100
100
15.8
56.6
103
65.1
200
19.1
59.4
110
Copper C=130 ID 2.062" 0.268 0.569 0.962 1.45 2.03 2.71 3.47 4.31 5.24 6.22 7.34 9.78 12.5 15.6 18.9 22.5 26.6 30.7 35.2 40.1 45.1 50.5 56.1
62 68
Flow U.S. Gal.
Min. 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 220 240 260 280 300
2-1/2"
Velocity Plastic ft/sec
Plastic Steel Copper C=140 C=100 C=130 ID 2.469" ID 2.469" ID 2.50"
1.3
0.353 0.654 0.375
2.0
0.75
1.39 0.792
2.7
1.27
2.36 1.35
3.4
1.92
3.56 2.04
4.0
2.69
4.99 2.86
4.7
3.58
6.64 3.82
5.4
4.59
8.5 4.88
6.0
5.72
10.6 6.06
6.7
6.9
12.8 7.37
7.4
8.25
15.3
8.8
8.0
9.71
18
10.3
8.7
11.3
20.9
12
9.4
12.9
23.9 13.7
10.1
14.7
27.3 15.6
10.7
16.6
30.7 17.6
11.4
18.5
34.3 19.7
12.1
20.6
38.1 21.9
12.7
22.7
42.1 24.2
13.4
25
46.3 26.6
14.7
29.8
55.3 31.8
16.1
35.8
66.4 37.4
17.4
41.6
75.3 43.3
18.8
46.6
86.3 49.4
20.1
52.9
98.1 56.8
NOTE: Recommended velocity is 5 FPS (feet per second) with a maximum of 7 FPS.
Note (1) Loss Figures are based on equivalent lengths of indicated pipe material Note (2) Loss Figures for screwed valves based on equivalent lengths of steel pipe.
104
GENERAL INFORMATION
Cable Selection Guide Hitachi® 6"-8" Submersible Motors
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
60° C
MOTOR
FUSE
AWG
MCM
VOLTS /
Dual
HZ HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE 5 4 45
25 149 237 378 598 931 1484 1865 2356 2967 3746 4726 5966 7516 8873
8 6 60 35
- - 247 391 609 970 1220 1540 1940 2449 3090 3901 4914 5802 6965 8142 9308
10 8 80 45
- - - 308 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125
230 V 15 11 125 70 60 Hz 20 15 150 90
- - - 221 344 548 689 871 1097 1384 1746 2205 2778 3279 3937 4602 5261 6546 - - - - 264 420 528 667 841 1061 1339 1690 2130 2514 3018 3528 4034 5019
25 19 200 100 - - - - - 332 417 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 225 125 - - - - - - 337 426 537 677 855 1079 1359 1605 1926 2252 2575 3203
40* 30 300 175 - - - - - - - 328 413 522 659 831 1047 1236 1484 1735 1984 2468
5 4 20 10 595 947 1511 2393 3723 5935 7461 9422
8 6 30 15 389 619 988 1564 2434 3880 4878 6161 7761 9797
10 8 40 20 307 488 778 1233 1918 3057 3844 4854 6115 7719 9738
15 11 60 30
- 350 558 884 1376 2193 2757 3482 4387 5537 6986 8819
20 15 80 45
- - 428 678 1055 1682 2114 2670 3363 4245 5356 6761 8518
25 19 100 50
- - - 535 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 110 60
- - - 433 673 1073 1349 1704 2147 2710 3419 4316 5437 6419 7706 9008
40 30 150 80
460 V 60 Hz
40*
30
150
80
50 37 175 100
- - - - 519 827 1040 1313 1654 2088 2634 3325 4189 4946 5937 6940 7935 9873 - - - - 502 801 1007 1271 1601 2022 2550 3220 4056 4789 5749 6720 7683 9559 - - - - - 639 803 1014 1277 1612 2034 2568 3235 3819 4585 5359 6127 7623
50* 37 175 100 - - - - - 691 869 1097 1382 1745 2201 2779 3501 4133 4961 5799 6631 8250
60 45 225 125 - - - - - - 675 852 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407
60* 45 225 125 - - - - - - 705 890 1121 1415 1785 2254 2839 3352 4024 4704 5378 6691
75 55 250 150 - - - - - - - 735 926 1168 1474 1861 2344 2768 3323 3884 4441 5525
100 75 350 200 - - - - - - - - - 878 1108 1399 1762 2081 2498 2920 3338 4153
125 93 450 250 - - - - - - - - - - 893 1127 1420 1676 2012 2352 2689 3346
150 111 500 275 - - - - - - - - - - - - 1162 1371 1646 1924 2200 2737
Lengths only meet the US National Electrical Code ampacity requirements for individual conductors rated 60° C in free air or water, NOT in
magnetic enclosures, conduit or direct buried. Refer to NEC Table 310.15(B)(17) for more information.
* = motors are 8" diameter
105
GENERAL INFORMATION
Cable Selection Guide Hitachi® 6"-8" Submersible Motors
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
75° C
MOTOR
FUSE
AWG
MCM
VOLTS /
Dual
HZ HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 4 45 25 149 237 378 598 931 1484 1865 2356 2967 3746 4726 5966 7516 8873
8 6 60 35
- 155 247 391 609 970 1220 1540 1940 2449 3090 3901 4914 5802 6965 8142 9308
10 8 80 45
230 V 15 11 125 70 60 Hz 20 15 150 90
- - 195 308 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125 - - - 221 344 548 689 871 1097 1384 1746 2205 2778 3279 3937 4602 5261 6546 - - - - 264 420 528 667 841 1061 1339 1690 2130 2514 3018 3528 4034 5019
25 19 200 100 - - - - 208 332 417 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 225 125 - - - - - 268 337 426 537 677 855 1079 1359 1605 1926 2252 2575 3203
40* 30 300 175 - - - - - - - 328 413 522 659 831 1047 1236 1484 1735 1984 2468
5 4 20 10 595 947 1511 2393 3723 5935 7461 9422
8 6 30 15 389 619 988 1564 2434 3880 4878 6161 7761 9797
10 8 40 20 307 488 778 1233 1918 3057 3844 4854 6115 7719 9738
15 11 60 30 220 350 558 884 1376 2193 2757 3482 4387 5537 6986 8819
20 15 80 45
- - 428 678 1055 1682 2114 2670 3363 4245 5356 6761 8518
25 19 100 50
- - 338 535 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 110 60
- - - 433 673 1073 1349 1704 2147 2710 3419 4316 5437 6419 7706 9008
40 30 150 80
460 V 60 Hz
40*
30
150
80
50 37 175 100
- - - - 519 827 1040 1313 1654 2088 2634 3325 4189 4946 5937 6940 7935 9873 - - - - 502 801 1007 1271 1601 2022 2550 3220 4056 4789 5749 6720 7683 9559 - - - - - 639 803 1014 1277 1612 2034 2568 3235 3819 4585 5359 6127 7623
50* 37 175 100 - - - - 433 691 869 1097 1382 1745 2201 2779 3501 4133 4961 5799 6631 8250
60 45 225 125 - - - - - 537 675 852 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407
60* 45 225 125 - - - - - 561 705 890 1121 1415 1785 2254 2839 3352 4024 4704 5378 6691
75 55 250 150 - - - - - - 582 735 926 1168 1474 1861 2344 2768 3323 3884 4441 5525
100 75 350 200 - - - - - - - - 696 878 1108 1399 1762 2081 2498 2920 3338 4153
125 93 450 250 - - - - - - - - - 708 893 1127 1420 1676 2012 2352 2689 3346
150 111 500 275 - - - - - - - - - - - 922 1162 1371 1646 1924 2200 2737
Lengths only meet the US National Electrical Code ampacity requirements for individual conductors rated 75° C in free air or water, NOT in
magnetic enclosures, conduit or direct buried. Refer to NEC Table 310.15(B)(17) for more information.
* = motors are 8" diameter
106
GENERAL INFORMATION
Cable Selection Guide Hitachi® 6"-8" Submersible Motors
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
60° C
MOTOR
FUSE
AWG
MCM
Dual VOLTS HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 4 45 25
- - 378 598 931 1484 1865 2356 2967 3746 4726 5966 7516 8873
8 6 60 35
- - - 391 609 970 1220 1540 1940 2449 3090 3901 4914 5802 6965 8142 9308
10 8 80 45
- - - - 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125
230 V 15 11 125 70 60 Hz 20 15 150 90
- - - - - 548 689 871 1097 1384 1746 2205 2778 3279 3937 4602 5261 6546 - - - - - - 528 667 841 1061 1339 1690 2130 2514 3018 3528 4034 5019
25 19 200 100 - - - - - - - 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 225 125 - - - - - - - - - 677 855 1079 1359 1605 1926 2252 2575 3203
40* 30 300 175 - - - - - - - - - - - 831 1047 1236 1484 1735 1984 2468
5 4 20 10 595 947 1511 2393 3723 5935 7461 9422
8 6 30 15
- 619 988 1564 2434 3880 4878 6161 7761 9797
10 8 40 20
- - 778 1233 1918 3057 3844 4854 6115 7719 9738
15 11 60 30
- - 558 884 1376 2193 2757 3482 4387 5537 6986 8819
20 15 80 45
- - - 678 1055 1682 2114 2670 3363 4245 5356 6761 8518
25 19 100 50
- - - - 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 110 60
- - - - - 1073 1349 1704 2147 2710 3419 4316 5437 6419 7706 9008
40 30 150 80
460 V 60 Hz
40* 30
150
80
50 37 175 100
- - - - - - 1040 1313 1654 2088 2634 3325 4189 4946 5937 6940 7935 9873 - - - - - - 1007 1271 1601 2022 2550 3220 4056 4789 5749 6720 7683 9559 - - - - - - - - 1277 1612 2034 2568 3235 3819 4585 5359 6127 7623
50* 37 175 100 - - - - - - - 1097 1382 1745 2201 2779 3501 4133 4961 5799 6631 8250
60 45 225 125 - - - - - - - - - 1355 1709 2158 2719 3210 3853 4504 5149 6407
60* 45 225 125 - - - - - - - - - 1415 1785 2254 2839 3352 4024 4704 5378 6691
75 55 250 150 - - - - - - - - - - 1474 1861 2344 2768 3323 3884 4441 5525
100 75 350 200 - - - - - - - - - - - - 1762 2081 2498 2920 3338 4153
125 93 450 250 - - - - - - - - - - - - - - 2012 2352 2689 3346
150 111 500 275 - - - - - - - - - - - - - - - - 2200 2737
Lengths meet the US National Electrical Code ampacity requirements for either individual conductors or jacketed rated 60° C cable and can
be in conduit or direct buried. Flat molded and web/ribbon cable are considered jacketed cable. Refer to NEC Table 310.15(B)(16) for more
information.
* = motors are 8" diameter
107
GENERAL INFORMATION
Cable Selection Guide Hitachi® 6"-8" Submersible Motors
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
75° C
MOTOR
FUSE
AWG
MCM
Dual VOLTS HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 4 45 25
- 237 378 598 931 1484 1865 2356 2967 3746 4726 5966 7516 8873
8 6 60 35
- - 247 391 609 970 1220 1540 1940 2449 3090 3901 4914 5802 6965 8142 9308
10 8 80 45
- - - 308 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125
230 V 15 11 125 70 60 Hz 20 15 150 90
- - - - 344 548 689 871 1097 1384 1746 2205 2778 3279 3937 4602 5261 6546 - - - - - 420 528 667 841 1061 1339 1690 2130 2514 3018 3528 4034 5019
25 19 200 100 - - - - - - 417 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 225 125 - - - - - - - - 537 677 855 1079 1359 1605 1926 2252 2575 3203
40* 30 300 175 - - - - - - - - - - 659 831 1047 1236 1484 1735 1984 2468
5 4 20 10 595 947 1511 2393 3723 5935 7461 9422
8 6 30 15 389 619 988 1564 2434 3880 4878 6161 7761 9797
10 8 40 20
- 488 778 1233 1918 3057 3844 4854 6115 7719 9738
15 11 60 30
- - 558 884 1376 2193 2757 3482 4387 5537 6986 8819
20 15 80 45
- - - 678 1055 1682 2114 2670 3363 4245 5356 6761 8518
25 19 100 50
- - - 535 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 110 60
- - - - 673 1073 1349 1704 2147 2710 3419 4316 5437 6419 7706 9008
40 30 150 80
460 V 60 Hz
40*
30
150
80
50 37 175 100
- - - - - 827 1040 1313 1654 2088 2634 3325 4189 4946 5937 6940 7935 9873 - - - - - 801 1007 1271 1601 2022 2550 3220 4056 4789 5749 6720 7683 9559 - - - - - - 803 1014 1277 1612 2034 2568 3235 3819 4585 5359 6127 7623
50* 37 175 100 - - - - - - 869 1097 1382 1745 2201 2779 3501 4133 4961 5799 6631 8250
60 45 225 125 - - - - - - - - 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407
60* 45 225 125 - - - - - - - 890 1121 1415 1785 2254 2839 3352 4024 4704 5378 6691
75 55 250 150 - - - - - - - - - 1168 1474 1861 2344 2768 3323 3884 4441 5525
100 75 350 200 - - - - - - - - - - - 1399 1762 2081 2498 2920 3338 4153
125 93 450 250 - - - - - - - - - - - - 1420 1676 2012 2352 2689 3346
150 111 500 275 - - - - - - - - - - - - - - 1646 1924 2200 2737
Lengths meet the US National Electrical Code ampacity requirements for either individual conductors or jacketed rated 75° C cable and can
be in conduit or direct buried. Flat molded and web/ribbon cable are considered jacketed cable. Refer to NEC Table 310.15(B)(16) for more
information.
* = motors are 8" diameter
108
GENERAL INFORMATION
Cable Selection Guide Pentek® 6" Submersible Motors
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
60° C
MOTOR
FUSE
AWG
MCM
VOLTS /
Dual
HZ HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 3.7 45 25 154 245 391 620 965 1538 1933 2442 3076 3883 4899 6184 7791 9198
7.5 5.5 60 40
- 174 277 438 682 1087 1367 1726 2174 2745 3463 4372 5508 6502 7806 9124
230 V 60 Hz
10 7.5 90 15 11 125
50 80
20 15 175 110
- - - 308 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125 - - - 216 337 537 675 852 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407 - - - - 251 400 503 636 801 1011 1275 1610 2028 2394 2874 3360 3842 4780
25 18.5 225 125 - - - - - 332 417 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 250 125 - - - - - - 373 471 593 749 945 1193 1503 1775 2130 2490 2847 3543
5 3.7 20 10 617 982 1566 2480 3859 6152 7734 9767
7.5 5.5 30 20 436 694 1107 1753 2728 4349 5467 6904 8698
460 V 10 7.5 45 25 307 488 778 1233 1918 3057 3844 4854 6115 7719 9738
60 Hz 15 11 70
40
- 343 546 865 1347 2147 2699 3408 4293 5419 6837 8631
or 380 V
20 15
90
50
- - 408 646 1005 1601 2013 2543 3203 4043 5101 6439 8113 9578
50 Hz 25 18.5 110 60
- - - 535 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 125 70
- - - 479 745 1187 1492 1884 2374 2997 3781 4773 6013 7099 8522 9961
40 30 150 100 - - - - 546 870 1093 1381 1740 2196 2770 3497 4406 5202 6244 7299 8345
Lengths only meet the US National Electrical Code ampacity requirements for individual conductors rated 60° C in free air or water, NOT in magnetic enclosures, conduit or direct buried. Refer to NEC Table 310.15(B)(17) for more information.
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
75° C
MOTOR
FUSE
AWG
MCM
VOLTS /
Dual
HZ HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 3.7 45 25
- 245 391 620 965 1538 1933 2442 3076 3883 4899 6184 7791 9198
7.5 5.5 60 40
- - 277 438 682 1087 1367 1726 2174 2745 3463 4372 5508 6502 7806 9124
10 7.5 90 50
230 V 60 Hz
15
11 125
80
20 15 175 110
- - - 308 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125 - - - - 337 537 675 852 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407 - - - - - 400 503 636 801 1011 1275 1610 2028 2394 2874 3360 3842 4780
25 18.5 225 125 - - - - - - 417 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 250 125 - - - - - - - 471 593 749 945 1193 1503 1775 2130 2490 2847 3543
5 3.7 20 10 617 982 1566 2480 3859 6152 7734 9767
7.5 5.5 30 20 436 694 1107 1753 2728 4349 5467 6904 8698
460 V 10 7.5 45
25
- 488 778 1233 1918 3057 3844 4854 6115 7719 9738
60 Hz or
380 V
15 11 20 15
70 90
40 50
50 Hz 25 18.5 110 60
- - 546 865 1347 2147 2699 3408 4293 5419 6837 8631 - - - 646 1005 1601 2013 2543 3203 4043 5101 6439 8113 9578 - - - 535 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 125 70
- - - - 745 1187 1492 1884 2374 2997 3781 4773 6013 7099 8522 9961
40 30 150 100 - - - - - 870 1093 1381 1740 2196 2770 3497 4406 5202 6244 7299 8345
Lengths only meet the US National Electrical Code ampacity requirements for individual conductors rated 75° C in free air or water, NOT in
magnetic enclosures, conduit or direct buried. Refer to NEC Table 310.15(B)(17) for more information.
109
GENERAL INFORMATION
Cable Selection Guide Pentek® 6" Submersible Motors
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
60° C
MOTOR
FUSE
AWG
MCM
Dual VOLTS HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 3.7 45 25
- - 391 620 965 1538 1933 2442 3076 3883 4899 6184 7791 9198
7.5 5.5 60 40
- - 277 438 682 1087 1367 1726 2174 2745 3463 4372 5508 6502 7806 9124
230 V 60 Hz
10 7.5 90 15 11 125
50 80
20 15 175 110
- - - - 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125 - - - - - 537 675 852 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407 - - - - - - 503 636 801 1011 1275 1610 2028 2394 2874 3360 3842 4780
25 18.5 225 125 - - - - - - - 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 250 125 - - - - - - - - 593 749 945 1193 1503 1775 2130 2490 2847 3543
5 3.7 20 10 617 982 1566 2480 3859 6152 7734 9767
7.5 5.5 30 20 436 694 1107 1753 2728 4349 5467 6904 8698
460 V 10 7.5 45 25
60 Hz or
380 V
15 11 20 15
70 90
40 50
- - 778 1233 1918 3057 3844 4854 6115 7719 9738 - - 546 865 1347 2147 2699 3408 4293 5419 6837 8631 - - - 646 1005 1601 2013 2543 3203 4043 5101 6439 8113 9578
50 Hz 25 18.5 110 60
- - - - 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 125 70
- - - - 745 1187 1492 1884 2374 2997 3781 4773 6013 7099 8522 9961
40 30 150 100 - - - - - - 1093 1381 1740 2196 2770 3497 4406 5202 6244 7299 8345
Lengths meet the US National Electrical Code ampacity requirements for either individual conductors or jacketed rated 60° C cable and can be in conduit or direct buried. Flat molded and web/ribbon cable are considered jacketed cable. Refer to NEC Table 310.15(B)(16) for more information.
* = motors are 8" diameter
CABLE SELECTION
COPPER CABLE SIZE - From Control Box to Motor (in feet)
75° C
MOTOR
FUSE
AWG
MCM
Dual VOLTS HP KW STD Element 14 12 10 8 6 4 3 2 1 0 00 000 0000 250 300 350 400 500
THREE PHASE
5 3.7 45 25
- 245 391 620 965 1538 1933 2442 3076 3883 4899 6184 7791 9198
7.5 5.5 60 40
- - 277 438 682 1087 1367 1726 2174 2745 3463 4372 5508 6502 7806 9124
10 7.5 90 50
230 V 60 Hz
15
11 125
80
20 15 175 110
- - - 308 479 764 961 1213 1529 1930 2434 3073 3872 4571 5488 6415 7334 9125 - - - - 337 537 675 852 1073 1355 1709 2158 2719 3210 3853 4504 5149 6407 - - - - - 400 503 636 801 1011 1275 1610 2028 2394 2874 3360 3842 4780
25 18.5 225 125 - - - - - - 417 527 664 838 1057 1334 1681 1985 2383 2785 3184 3962
30 22 250 125 - - - - - - - 471 593 749 945 1193 1503 1775 2130 2490 2847 3543
5 3.7 20 10 617 982 1566 2480 3859 6152 7734 9767
7.5 5.5 30 20 436 694 1107 1753 2728 4349 5467 6904 8698
460 V 10 7.5 45
25
60 Hz or
380 V
15 11 20 15
70 90
40 50
- 488 778 1233 1918 3057 3844 4854 6115 7719 9738 - - 546 865 1347 2147 2699 3408 4293 5419 6837 8631 - - - 646 1005 1601 2013 2543 3203 4043 5101 6439 8113 9578
50 H 25 18.5 110 60
- - - 535 833 1328 1669 2108 2655 3351 4228 5338 6725 7939 9531
30 22 125 70
- - - - 745 1187 1492 1884 2374 2997 3781 4773 6013 7099 8522 9961
40 30 150 100 - - - - - 870 1093 1381 1740 2196 2770 3497 4406 5202 6244 7299 8345
Lengths meet the US National Electrical Code ampacity requirements for either individual conductors or jacketed rated 75° C cable and can
be in conduit or direct buried. Flat molded and web/ribbon cable are considered jacketed cable. Refer to NEC Table 310.15(B)(16) for more
information.
110
NOTES 111
NOTES 112
Limited Warranty
Myers® warrants to the original consumer purchaser ("Purchaser" or "You") of the products listed below, that they will be free from defects in material and workmanship for the Warranty Period shown below.
Product Water Systems Products -- jet pumps, small centrifugal pumps, submersible pumps and related accessories Pro-SourceTM Composite Tanks
Pro-Source Steel Pressure Tanks
Pro-Source Epoxy-Lined Tanks
Sump/Sewage/Effluent Products
Warranty Period Whichever occurs first: 12 months from date of original installation, or 18 months from date of manufacture 5 years from date of original installation
5 years from date of original installation
3 years from date of original installation
24 months from date of original installation
Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence, misapplication, improper installation, or improper maintenance. Without limiting the foregoing, operating a three phase motor with single phase power through a phase converter will void the warranty. Note also that three phase motors must be protected by three-leg, ambient compensated, extra-quick trip overload relays of the recommended size or the warranty is void.
Your only remedy, and Myers's only duty, is that Myers repair or replace defective products (at Myer's choice). You must pay all labor and shipping charges associated with this warranty and must request warranty service through the installing dealer as soon as a problem is discovered. No request for service will be accepted if received after the Warranty Period has expired. This warranty is not transferable.
MYERS SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION EXPRESSLY PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of an implied warranty, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may also have other rights which vary from state to state.
This warranty supersedes and replaces all previous warranty publications.
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.FEMYERS.COM PH: 888-987-8677 ORDERS FAX: 800-426-9446 Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
© 2013 Pentair Ltd. All Rights Reserved.
M9107WS (07/16/13)