Home › AOS-CX 10.06.0140 Release Notes for 8400 Switches

AOS-CX 10.06.0140 Release Notes for 8400 Switches

File info: application/pdf · 34 pages · 305.34KB

AOS-CX, 10.06.0140, Release, Notes, for, 8400, Switches

AOS-CX10.06ReleaseNotes|6 Versionnumber Releasedate Remarks 10.06.0130 2021-06-10 Released,fullysupported,andpostedontheweb. 10.06.0120 2021-04-29 Released ...

Original Document

If the viewer doesn’t load, open the PDF directly.

Extracted Text

AOS-CX 10.06.0140 Release Notes
8400 Switch Series
Published: August 2021 Edition: 1

Copyright Information � Copyright 2021 Hewlett Packard Enterprise Development LP. Open Source Code This product includes code licensed under the GNU General Public License, the GNU Lesser General Public License, and/or certain other open source licenses. A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to: Hewlett Packard Enterprise Company 6280 America Center Drive San Jose, CA 95002 USA
Notices
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein. Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise website.
Acknowledgments
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
|2

Chapter 1 AOS-CX 10.06 Release Notes
AOS-CX 10.06 Release Notes
Description
This release note covers software versions for the AOS-CX 10.06 branch of the software.
If you run the show version command on the switch, the version number will display XL.10.06.xxxx, where xxxx is the minor version number.
AOS-CX is a new, modern, fully programmable operating system built using a database-centric design that ensures higher availability and dynamic software process changes for reduced downtime. In addition to robust hardware reliability, the AOS-CX operating system includes additional software elements not available with traditional systems, including the features included in the Features section of this release note. Version 10.06.0001 is the initial build of major version 10.06 software. Product series supported by this software: n Aruba 8400 Switch Series
Important Information
Aruba switches covered by this release note use eMMC or SSD storage. This is non-volatile memory for persistent storage of config, files, databases, scripts, and so forth. Aruba recommends updating to version 10.05.0060 or 10.06.0100 or later (including this release) to implement significant improvements to memory usage and prolong the life of the switch.
To avoid damage to your equipment, do not interrupt power to the switch during a software update.
10.03 is the minimum required software version prior to upgrading to 10.06. If your device is using a version of software prior to 10.03, you must first upgrade to a version of 10.03 before upgrading to 10.06. Check release notes for the software version you will upgrade to for instructions on performing the upgrade to 10.03.
If using the Web UI, you should clear the browser cache after upgrading to this version of software before logging into the switch using a Web UI session. This will ensure the Web UI session downloads the latest changes.

AOS-CX 10.06.0140 Release Notes | for 8400 Switches

3

If a switch has RPVST enabled and the native VLAN ID configured for a trunk interface is not the default VLAN ID 1, and the native VLAN ID is also used as the management VLAN, the switch may not be accessible over the trunk interface after upgrading from any 10.04.00xx version of software to 10.06.xxxx. To fix the issue after an upgrade, log into the switch using the OOBM interface or serial port console and configure the following:
switch# configure switch(config)# spanning-tree rpvst-mstp-interconnect-vlan <VLAN_ID>
where <VLAN_ID> is the native VLAN ID configured on the trunk interface. If there are multiple trunk interfaces configured on the switch, each with a different VLAN ID, contact the Aruba Support Team.
When upgrading from software versions before 10.05.0001, if the switch is configured with an entry in a classmap or an Access List that matches AH or ESP traffic, the policy will fail to apply, as these options are no longer permitted. Remove such entries from the configuration prior to upgrading to 10.06.0140 or remove the respective entries from ACLs or Class that failed to apply after the upgrade to 10.06.0140.
When upgrading from a version of software prior to version 10.05.0001, if the switch is configured with IGMP or MLD snooping options such as "forward", "fastleave", "forced-fastleave", or "blocked" at the VLAN context, after upgrading to this software version, you will need to reconfigure these options for each interface from the interface configuration context. Example config before 10.05.0001:
vlan 2 ip igmp snooping forward 1/1/1 ip igmp snooping blocked 1/1/2 ip igmp snooping force-fastleave 1/1/3 ip igmp snooping fastleave 1/1/4
Example config to be added after upgrade to this software version:
interface 1/1/1 ip igmp snooping forward vlan 2
interface 1/1/2 ip igmp snooping blocked van 2
interface 1/1/3 ip igmp snooping forced-fastleave vlan 2
interface 1/1/4 ip igmp snooping fastleave vlan 2
AOS-CX 10.06 Release Notes | 4

To restore a previous configuration when downgrading to a previous version of software, follow these steps:
1. Use the show checkpoint command to see the saved checkpoints and ensure that you have a checkpoint that is an exact match of the target software version (see the Image Version column in the output of the command, for example, XL.10.06.0100). This checkpoint can be the startup-config-backup automatically created during the initial upgrade or any other manually created checkpoint for the target software version.
2. Copy the backup checkpoint into the startup-config.
3. Boot the switch to the target version (lower version), making sure to select no when prompted to save the current configuration.

Industry and Government Certifications
Refer to the Approved Product Lists sites for the Common Criteria, FIPS 140-2 and DoDIN APL to obtain the product certification details. Products should be used as evaluated and defined in the respective configuration guides.
n Common Criteria: https://www.niap-ccevs.org/Product/ n FIPS 140-2: https://csrc.nist.gov/Projects/Cryptographic-Module-Validation-Program/Validated-
Modules/Search n DoDIN APL: https://aplits.disa.mil/processAPList.action
License Written Offer
This product includes code licensed under the GNU General Public License, the GNU Lesser General Public License, and/or certain other open-source licenses. A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:
Hewlett Packard Enterprise Company Attn: General Counsel 6280 America Center Drive San Jose, CA 95002 U.S.A.

Please specify the product and version for which you are requesting source code. You may also request a copy of this source code free of charge at: https://hpe.com/software/opensource