For further information see masterCONFIGURATOR manual. 6.15 deviceCONFIGURATOR. PC (windows) based software application to transfer parameters into ...
Subject to change without notice. Information provided without guarantee. www.tridonic.com 3 Data sheet 09/21-LC562-10 LED Driver INDUSTRY Linear Dimming Specific technical data
LED Driver INDUSTRY Linear Dimming Driver LCI 150W 325-1050mA 300V o4a sl PRE mod (INDUSTRY) premium series non-SELV Product description · Constant current built-in Driver for LED, particularly suitable for industrial applications in moderate environments such as semiconductor factories or logistic warehouses · Dimming range 1 100 % · Adjustable output current between 325 and 1,050 mA · Max. output power 150 W · Suitable for mains voltage peaks (burst/surge) up to 4 kV · Expanded temperature range of -25 ... +50 °C · Nominal life-time up to 100,000 h (at ta 50 °C) · 5-year guarantee Housing properties · White slim metal casing · Type of protection IP20 Interfaces · one4all (DALI-2 DT 6, DSI, switchDIM, corridorFUNCTION) · ready2mainsTM (configuration and dimming via mains) · Terminal blocks: 0° push terminals Functions · Adjustable output current in 1-mA-steps (I-SELECT resistor or eD) · Constant light output function (CLO) · Power-up fading at AC · Intelligent Temperature Guard (overtemperature protection) · Intelligent Voltage Guard (overvoltage and undervoltage shutdown) · Protective features (overtemperature, short-circuit, overload, no-load, input voltage range) · Suitable for emergency lighting acc. to EN 50172 Benefits · Application-oriented operating window for maximum compatibility · Best energy savings due to low stand-by losses · Flexible configuration via DALI, ready2mainsTM and I-SELECT 2 · Reliability proven by life-time up to 100,000 h and 5-year guarantee · High reliability through the selection of exclusive components Typical applications · For linear/area lighting in industry applications · È Standards, page 5 Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 1 LED Driver INDUSTRY Linear Dimming EL Driver LCI 150W 325-1050mA 300V o4a sl PRE mod (INDUSTRY) premium series non-SELV Technical data Rated supply voltage 220 240 V AC voltage range 198 264 V DC voltage range 176 280 V Mains frequency 0 / 50 / 60 Hz Overvoltage protection 320 V AC, 48 h Typ. current (at 230 V, 50 Hz, full load)1 2 681 mA Typ. current (220 V, 0 Hz, full load, 15 % dimming level)2 119 mA Leakage current (at 230 V, 50 Hz, full load)1 2 < 250 µA Max. input power 157.1 W Typ. efficiency (at 230 V / 50 Hz / full load)2 95 % (at 230 V, 50 Hz, full load)1 0.98 Typ. power input on stand-by3 < 0.25 W Typ. input current in no-load operation 78 mA Typ. input power in no-load operation 0.54 W In-rush current (peak / duration) 17.7 A / 162 s THD (at 230 V, 50 Hz, full load)1 < 4 % Starting time (at 230 V, 50 Hz, full load)1 < 0.6 s Starting time (DC mode) < 0.4 s Switchover time (AC/DC)7 < 0.4 s Turn off time (at 230 V, 50 Hz, full load) < 2.4 ms Output current tolerance1 6 ± 3 % Max. output current peak (non-repetitive) output current + 30 % Output LF current ripple (< 120 Hz) Output PstLM Output SVM ± 2 % 1 0.4 Max. output voltage (no-load voltage) 350 V Dimming range 1 100 % Mains surge capability (between L N) 4 kV Mains surge capability (between L/N PE) 4 kV Surge voltage at output side (against PE) 4 kV Type of protection IP20 Life-time up to 100,000 h Dimensions L x W x H 360 x 30 x 28 mm side fixing feature Ø Ordering data Type LCI 150/325-1050/300 o4a sl PRE mod Article number Packaging carton 28002054 10 pc(s). Packaging pallet 550 pc(s). Weight per pc. 0.321 kg Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 2 LED Driver INDUSTRY Linear Dimming Specific technical data Type Output Min. forward Max. forward Max. output Typ. power consumption Typ. current consumption Max. casing Ambient I-SELECT 2 current4 6 voltage voltage power (at 230 V, 50 Hz, full load) (at 230 V, 50 Hz, full load) temperature tc temperature ta max. resistor value5 325 mA 80 V 300 V 97.5 W 101.2 W 447 mA 68 °C -25 ... +50 °C open 400 mA 80 V 300 V 120.0 W 124.3 W 546 mA 68 °C -25 ... +50 °C 12.50 k 450 mA 80 V 300 V 135.0 W 139.7 W 611 mA 68 °C -25 ... +50 °C 11.11 k 500 mA 80 V 300 V 150.0 W 155.1 W 677 mA 68 °C -25 ... +50 °C 10.00 k 550 mA 80 V 273 V 150.0 W 155.2 W 678 mA 70 °C -25 ... +50 °C 9.09 k 600 mA 80 V 250 V 150.0 W 155.4 W 679 mA 70 °C -25 ... +50 °C 8.33 k 650 mA 80 V LCI 150/325-1050/300 o4a sl PRE mod 700 mA 80 V 750 mA 80 V 231 V 214 V 200 V 150.0 W 150.0 W 150.0 W 155.5 W 155.7 W 155.8 W 679 mA 680 mA 681 mA 70 °C 70 °C 70 °C -25 ... +50 °C -25 ... +50 °C -25 ... +50 °C 7.69 k 7.14 k 6.67 k 800 mA 80 V 188 V 150.0 W 156.0 W 682 mA 70 °C -25 ... +50 °C 6.25 k 850 mA 80 V 176 V 150.0 W 156.2 W 683 mA 70 °C -25 ... +50 °C 5.88 k 900 mA 80 V 167 V 150.0 W 156.5 W 684 mA 72 °C -25 ... +50 °C 5.56 k 950 mA 80 V 158 V 150.0 W 156.7 W 684 mA 72 °C -25 ... +50 °C 5.26 k 1,000 mA 80 V 150 V 150.0 W 156.9 W 685 mA 72 °C -25 ... +50 °C 5.00 k 1,050 mA 80 V 143 V 150.0 W 157.1 W 686 mA 72 °C -25 ... +50 °C short circuit (0 ) 1 Valid at 100 % dimming level. 2 Depending on the selected output current. 3 Depending on the DALI traffic at the interface. 4 The table only lists a number of possible operating points but does not cover each single point. The output current can be set within the total value range in 1-mA-steps. 5 Not compatible with I-SELECT (generation 1). Calculated resistor value. 6 Output current is mean value. 7 Valid for immediate change of power supply type otherwise the starting time is valid. Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 3 LED Driver INDUSTRY Linear Dimming I-SELECT 2 PLUG PRE / EXC ACCESSORIES Product description · Ready-for-use resistor to set output current value · Compatible with LED Driver featuring I-SELECT 2 interface; not compatible with I-SELECT (generation 1) · Resistor is base insulated · Resistor power 0.25 W · Current tolerance ± 2 % additional to output current tolerance · Compatible with LED Driver series PRE and EXC xxxx xxxx 7,5 5,5 4,5 13,5 9 Example of calculation for third party resistors · R [k] = 5 V / I_out [mA] x 1000 · E96 resistor value used · Resistor value tolerance 1 %; resistor power 0.1 W; base insulation necessary · When using a resistor value beyond the specified range, the output current will automatically be set to the minimum value (resistor value too big), respectively to the maximum value (resistor value too small) 3,5 Ordering data Type Article Resistor Colour Marking Current number value I-SELECT 2 PLUG 325MA BL 28001109 Blue 0325 mA 325 mA 15.40 k I-SELECT 2 PLUG 350MA BL 28001110 Blue 0350 mA 350 mA 14.30 k I-SELECT 2 PLUG 375MA BL 28001111 Blue 0375 mA 375 mA 13.30 k I-SELECT 2 PLUG 400MA BL 28001112 Blue 0400 mA 400 mA 12.40 k I-SELECT 2 PLUG 425MA BL 28001151 Blue 0425 mA 425 mA 11.80 k I-SELECT 2 PLUG 450MA BL 28001113 Blue 0450 mA 450 mA 11.00 k I-SELECT 2 PLUG 475MA BL 28001252 Blue 0475 mA 475 mA 10.50 k I-SELECT 2 PLUG 500MA BL 28001114 Blue 0500 mA 500 mA 10.00 k I-SELECT 2 PLUG 525MA BL 28001960 Blue 0525 mA 525 mA 9.53 k I-SELECT 2 PLUG 550MA BL 28001115 Blue 0550 mA 550 mA 9.09 k I-SELECT 2 PLUG 600MA BL 28001116 Blue 0600 mA 600 mA 8.25 k I-SELECT 2 PLUG 650MA BL 28001117 Blue 0650 mA 650 mA 7.68 k I-SELECT 2 PLUG 700MA BL 28001118 Blue 0700 mA 700 mA 7.15 k I-SELECT 2 PLUG 750MA BL 28001119 Blue 0750 mA 750 mA 6.65 k I-SELECT 2 PLUG 800MA BL 28001120 Blue 0800 mA 800 mA 6.19 k I-SELECT 2 PLUG 850MA BL 28001121 Blue 0850 mA 850 mA 5.90 k I-SELECT 2 PLUG 900MA BL 28001122 Blue 0900 mA 900 mA 5.62 k I-SELECT 2 PLUG 950MA BL 28001123 Blue 0950 mA 950 mA 5.23 k I-SELECT 2 PLUG 1000MA BL 28001124 Blue 1000 mA 1,000 mA 4.99 k I-SELECT 2 PLUG 1050MA BL 28001125 Blue 1050 mA 1,050 mA 4.75 k I-SELECT 2 PLUG MAX BL 28001099 Blue MAX MAX 0.00 k Packaging Weight bag per pc. 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg 10 pc(s). 0.001 kg Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 4 LED Driver INDUSTRY Linear Dimming 1. Standards EN 55015 EN 60068-2-27 (shock test case: 1,000 shocks in 6 directions with 30 g / 18 ms) EN 60068-2-64 (vibration test case: acc. to table A.1 transport / category 2) EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 62384 EN 61547 EN 62386-101 (DALI-2) EN 62386-102 (DALI-2) EN 62386-207 (DALI-2) According to EN 50172 for use in central battery systems According to EN 60598-2-22 suitable for emergency lighting installations 2. Thermal details and life-time 2.1 Expected life-time Type Output current 325 500 mA LCI 150/325-1050/300 o4a sl PRE mod >500 850 mA >850 1,050 mA ta tc Life-time tc Life-time tc Life-time 40 °C 60 °C >100,000 h 62 °C >100,000 h 63 °C >100,000 h 45 °C 62 °C >100,000 h 66 °C >100,000 h 67 °C >100,000 h 50 °C 68 °C >100,000 h 70 °C 100,000 h 72 °C 80,000 h The LED Driver is designed for a life-time stated above under reference conditions and with a failure probability of less than 10 %. The relation of tc to ta temperature depends also on the luminaire design. If the measured tc temperature is approx. 5 K below tc max., ta temperature should be checked and eventually critical components (e.g. ELCAP) measured. Detailed information on request. 3. Installation / wiring 3.1 Circuit diagram V / / Hz L N DALI/DSI V / / Hz L N LCI / - / PRI SEC ~ o a sl PRE mod ~ LED LED Isel - Isel - (GND) DA/N DA/L 3.2 Wiring type and cross section Solid wire with a cross section of 0.5 1.5 mm². Strip 8 9 mm of insulation from the cables to ensure perfect operation of terminals. LED module/LED Driver/supply wire preparation: 0.5 1.5 mm² 8 9 mm R 3.3 Loose wiring LCI / - / PRI SEC ~ o a sl PRE mod ~ LED LED Isel - Isel - (GND) N DA/N R L DA/L switchDIM V / Hz For wiring in dimming operation with ready2mains refer to the ready2mains Gateway datasheet. Loosen wire through twisting and pulling or using a Ø 1mm release tool Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 5 LED Driver INDUSTRY Linear Dimming 3.4 Wiring guidelines · Run the secondary lines separately from the mains connections and lines to achieve good EMC performance. · The max. secondary cable length is 2 m (4 m circuit), this applies for LED output as well as for I-SELECT 2. · For good EMC performance, keep the LED wiring as short as possible. · Secondary switching is not permitted. · The LED Driver has no inverse-polarity protection on the secondary side. Wrong polarity can damage LED modules with no inverse-polarity protection. · Wrong wiring of the LED Driver can lead to malfunction or irreparable damage. · With mains transients of 4 kV can voltage peaks up to 4 kV occur against PE at the output of the LED Driver. This has to be considered concerning the dielectric strength of the LED module (insulation against PE). · To avoid the damage of the Driver, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.). Make sure that the LED Driver is operated within the given window under all operating conditions. Special attention needs to be paid at dimming and DC emergency operation as the forward voltage of the connected LED modules varies with the dimming level, due to the implemented amplitude dimming technology. Coming below the specified minimum output voltage of the LED Driver may cause the device to shut-down. See chapter "6.11 Light level in DC operation" for more information. 4.2 Efficiency vs load E iciency [ ] 3.5 Hot plug-in Hot plug-in is not supported due to residual output voltage of > 0 V. If a LED load is connected the device has to be restarted before the output will be activated again. This can be done via mains reset or via interface (DALI, DSI, switchDIM, ready2mains). 3.6 Earth connection 4.3 Power factor vs load Load [ ] Power factor The earth connection is conducted as protection earth (PE). The LED Driver can be earthed via earth terminal or metal housing. If the LED Driver will be earthed, protection earth (PE) has to be used. There is no earth connection required for the functionality of the LED Driver. Earth connection is recommended to improve following behaviour: · Electromagnetic interferences (EMI) · LED glowing at stand-by · Transmission of mains transients to the LED output In general it is recommended to earth the LED Driver if the LED module is mounted on earthed luminaire parts respectively heat sinks and thereby representing a high capacity against earth. 3.7 I-SELECT 2 resistors connected via cable For details see: http://www.tridonic.com/com/en/download/technical/LCA_PRE_LC_EXC_ProductManual_en.pdf. 4.4 THD vs load Load [ ] 4. Electrical values 4.1 Operating window THD [ ] Output voltage [V] Output current [mA] Operating window 100 % Operating window dimmed Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. Load [ ] mA mA mA mA 100 % load corresponds to the max. output power (full load) according to the table on page 2. www.tridonic.com 6 LED Driver INDUSTRY Linear Dimming 4.5 Maximum loading of automatic circuit breakers in relation to inrush current Automatic circuit breaker type Installation Ø LCI 150/325-1050/300 o4a sl PRE mod C10 1.5mm2 28 C13 1.5mm2 33 C16 2.5mm2 36 C20 4mm2 41 B10 1.5mm2 17 B13 1.5mm2 20 B16 2.5mm2 22 B20 4mm2 25 Inrush current I max 17.7 A time 162 s This are max. values calculated out of inrush current! Please consider not to exceed the maximum rated continuous current of the circuit breaker. Calculation uses typical values from ABB series S200 as a reference. Actual values may differ due to used circuit breaker types and installation environment. 4.6 Harmonic distortion in the mains supply (at 230 V / 50 Hz and full load) in % LCI 150/325-1050/300 o4a sl PRE mod THD 3. 5. 7. 9. 11. <4 <1 <4 <1 < 1 < 1 4.7 Dimming Dimming range 1% to 100% Digital control with: · DSI signal: 8 bit Manchester Code Speed 1% to 100% in 1.4 s · DALI signal: 16 bit Manchester Code Speed 1% to 100% in 0.2s Programmable parameter: Minimum dimming level Maximum dimming level Default minimum = 1% Programmable range 1% MIN 100% Default maximum = 100% Programmable range 100% MAX 1% Dimming curve is adapted to the eye sensitiveness. Dimming is realized by amplitude dimming. 5.2 Control input ready2mains (L, N) The digital ready2mains protocol is modulated onto the mains signal which is wired to the mains terminal (L and N). 5.3 switchDIM Integrated switchDIM function allows a direct connection of a pushbutton for dimming and switching. Brief push (< 0.6 s) switches LED Driver ON and OFF. The dimm level is saved at power-down and restored at power-up. When the pushbutton is held, LED modules are dimmed. After repush the LED modules are dimmed in the opposite direction. In installations with LED Drivers with different dimming levels or opposite dimming directions (e.g. after a system extension), all LED Drivers can be synchronized to 50% dimming level by a 10 s push. Use of pushbutton with indicator lamp is not permitted. 4Di.m8 mDiinmgmchinargacctheraisraticcsteristics Digital dimming value 255 225 200 DALI 175 DSI 150 125 100 75 50 25 0 0 10 20 30 40 50 60 70 80 90 100 Relative lighting level % Dimming characteristics as seen by the human eye 6. Functions 6.1 Function: adjustable current The output current of the LED Driver can be adjusted in a certain range. For adjustment there are three options available. Option 1: DALI Adjustment is done by masterCONFIGURATOR (see masterCONFIGURATOR documentation). Option 2: I-SELECT 2 By inserting a suitable resistor into the I-SELECT 2 interface, the current value can be adjusted. The relationship between output current and resistor value can be found in the chapter "Accessories I-SELECT 2 Plugs". Please note that the resistor values for I-SELECT 2 are not compatible with I-SELECT (generation 1). Installation of an incorrect resistor may cause irreparable damage to the LED module(s). 5. Interfaces / communication 5.1 Control input (DA/N, DA/L) Digital DALI signal or switchDIM can be wired on the same terminals (DA/N and DA/L). The control input is non-polar for digital control signals (DALI, DSI). The control signal is not SELV. Control cable has to be installed in accordance to the requirements of low voltage installations. Different functions depending on each module. Resistors for the main output current values can be ordered from Tridonic (see accessories). Option 3: ready2mains Adjustment is done by the ready2mains programmer and the corresponding configuration software (see ready2mains documentation). The priority for current adjustment methods is DALI (highest priority), I-SELECT 2, ready2mains (lowest priority). Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 7 LED Driver INDUSTRY Linear Dimming 6.2 ready2mains configuration 6.9 Constant light output (CLO) The ready2mains interface can be used to configure the main parameters of LED Drivers via the mains wiring, such as LED output current, CLO and DC level. These parameters can be adjusted either via ready2mains-capable configuration software or directly via the ready2mains programmer (output current only). 6.3 ready2mains dimming The luminous flux of a LED decreases constantly over the life-time. The CLO function ensures that the emitted luminous flux remains stable. For that purpose the LED current will increase continuously over the LED life-time. In masterCONFIGURATOR it is possible to select a start value (in percent) and an expected life-time. The LED Driver adjusts the current afterwards automatically. ready2mains allows for mains-based group dimming, controlled via the ready2mains protocol and appropriate dimming interfaces. For details on the operation of ready2mains and its components see the relevant technical information. 6.4 Short-circuit behaviour In case of a short-circuit at the LED output the LED output is switched off. After restart of the LED Driver the output will be activated again. The restart can either be done via mains reset or via interface (DALI, DSI, switchDIM, ready2mains). 6.5 No-load operation The LED Driver will not be damaged in no-load operation. The output will be deactivated and is therefore free of voltage. If a LED load is connected the device has to be restarted before the output will be activated again. 6.6 Overload protection 6.10 Power-up/-down fading The power-up/-down function offers the opportunity to modify the on-/off behavior. The time for fading on or off can be adjusted in a range of 0.2 to 16 seconds. According to this value, the device dims either from 0 % up to the power-on level or from the current set dim level down to 0 %. This feature applies while operating via switchDIM, ready2mains and when switching the mains voltage on or off. By factory default no fading time is set (= 0 seconds). 6.11 Light level in DC operation The LED Driver is designed to operate on DC voltage and pulsed DC voltage. For a reliable operation, make sure that also in DC emergency operation the LED Driver is run within the specified conditions as stated in chapter "4.1 operating window". Light output level in DC operation: programmable 1 100 % (EOFi = 0.13). Programming by DALI or ready2mains. In DC operation dimming mode can be activated. If the output voltage range is exceeded the LED Driver turns off the LED output. After restart of the LED Driver the output will be activated again. The restart can either be done via mains reset or via interface (DALI, DSI, switchDIM, ready2mains). 6.7 Overtemperature protection The voltage-dependent input current of Driver incl. LED module is depending on the used load. The voltage-dependent no-load current of Driver (without or defect LED module) is for: AC: < 19 mA DC: < 2 mA The LED Driver is protected against temporary thermal overheating. If the temperature limit is exceeded the output current of the LED module(s) is reduced. The temperature protection is activated above tc max. The activation temperature differs depending on the LED load. On DC operation this function is deactivated to fulfill emergency requirements. 6.8 corridorFUNCTION The corridorFUNCTION can be programmed in two different ways. To program the corridorFUNCTION by means of software a DALI-USB interface is needed in combination with a DALI PS. The software can be the masterCONFIGURATOR. To activate the corridorFUNCTION without using software a voltage of 230V has to be applied for five minutes at the switchDIM connection. The unit will then switch automatically to the corridorFUNCTION. 6.12 Intelligent Voltage Guard Intelligent Voltage Guard is the name of the electronic monitoring of the mains voltage. It immediately shows if the mains voltage rises above certain thresholds. Measures can then be taken quickly to prevent damage to the LED Driver. · If the mains voltage rises above approx. 280Vrms (voltage depends on the LED Driver type), the LED light starts flashing on and off. · To avoid a damage of the LED Driver the mains supply has to be switched off at this signal. Note: If the corridorFUNCTION is wrongly activated in a switchDIM system (for example a switch is used instead of pushbutton), there is the option of installing a pushbutton and deactivating the corridorFUNCTION mode by five short pushes of the button within three seconds. switchDIM and corridorFUNCTION are very simple tools for controlling gears with conventional pushbuttons or motion sensors. To ensure correct operation a sinusoidal mains voltage with a frequency of 50 Hz or 60 Hz is required at the control input. Special attention must be paid to achieving clear zero crossings. Serious mains faults may impair the operation of switchDIM and corridorFUNCTION. Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 8 LED Driver INDUSTRY Linear Dimming 6.13 Software / programming With appropriate software and an interface different functions can be activated and various parameters can be configured in the LED Driver. To do so, a DALI-USB or ready2mains programmer and the software (masterCONFIGURATOR) are required. 6.14 masterCONFIGURATOR From version 2.8: For programming functions (CLO, I-SELECT 2, power-up fading, corridorFUNCTION) and device settings (fade time, ePowerOnLevel, DC level, etc.). For further information see masterCONFIGURATOR manual. 6.15 deviceCONFIGURATOR PC (windows) based software application to transfer parameters into our drivers. Workflow optimised for the use in OEM production line. For further information see deviceCONFIGURATOR manual. 7. Miscellaneous 7.1 Insulation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A, each luminaire should be submitted to an insulation test with 500VDC for 1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The insulation resistance must be at least 2M. As an alternative, IEC 60598-1 Annex Q describes a test of the electrical strength with 1500VAC (or 1.414 x 1500VDC). To avoid damage to the electronic devices this test must not be conducted. 7.2 Conditions of use and storage Humidity: 5% up to max. 85%, not condensed (max. 56 days/year at 85%) Storage temperature: -40°C up to max. +80°C The devices have to be acclimatised to the specified temperature range (ta) before they can be operated. 7.3 Maximum number of switching cycles All LED Driver are tested with 50,000 switching cycles. The actually achieved number of switching cycles is significantly higher. 7.4 Additional information Additional technical information at www.tridonic.com Technical Data Guarantee conditions at www.tridonic.com Services Life-time declarations are informative and represent no warranty claim. No warranty if device was opened. Data sheet 04/20-LC562-8 Subject to change without notice. Information provided without guarantee. www.tridonic.com 9Adobe PDF Library 15.0 Adobe InDesign 15.0 (Windows)