u blox EMMYW165 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 User Manual NEO 7

u-blox AG WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 NEO 7

EMMY-W1_User_Manual

Download:
Mirror Download [FCC.gov]
Document ID	3172302
Application ID	/KNldCNPyNvVf5F61rMFHA==
Document Description	EMMY-W1_User_Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	160.33kB (2004066 bits)
Date Submitted	2016-10-24 00:00:00
Date Available	2016-10-25 00:00:00
Creation Date	2016-07-18 12:14:12
Producing Software	MicrosoftÂ® Word 2013
Document Lastmod	2016-07-18 12:14:12
Document Title	NEO-7
Document Creator	MicrosoftÂ® Word 2013
Document Author:	Error! No text of specified style in document.

EMMY-W1 series
Host-based multiradio modules with WiFi, Bluetooth and NFC
User Manual
Abstract
This technical data sheet describes the EMMY-W1 series modules
with Wi-Fi 802.11ac, Bluetooth v4.2 (Bluetooth® Smart Ready) and
Near-Field Communication (NFC) designed for both simultaneous
and independent operations. These modules include an integrated
MAC/baseband processor and RF front-end components and can
connect to a host processor through SDIO 3.0 or high-speed UART
interfaces. A PCM interface is available for Bluetooth audio
applications. These modules are offered in both professional and
automotive grades.
www.u-blox.com
UBX-16015271 - R03
EMMY-W1 series - User Manual
Document Information
Title
EMMY-W1 series
Subtitle
Host-based multiradio modules with Wi-Fi, Bluetooth and NFC
Document type
User Manual
Document number
UBX-16015271
Revision and date
R03
Document status
Product Information
05-July-2016
Document status explanation
Objective Specification
Document contains target values. Revised and supplementary data will be published later.
Advance Information
Document contains data based on early testing. Revised and supplementary data will be published later.
Early Production Information
Document contains data from product verification. Revised and supplementary data may be published later.
Production Information
Document contains the final product specification.
This document applies to the following products:
Product name
Type number
ROM/FLASH version
PCN / IN reference
EMMY-W161
EMMY-W161-00B-00
EMMY-W161-00B
N/A
EMMY-W161-A
EMMY-W161-00A-00
EMMY-W161-00A
N/A
EMMY-W163
EMMY-W163-00B-00
EMMY-W163-00B
N/A
EMMY-W163-A
EMMY-W163-00A-00
EMMY-W163-00A
N/A
EMMY-W165
EMMY-W165-00B-00
EMMY-W165-00B
N/A
EMMY-W165-A
EMMY-W165-00A-00
EMMY-W165-00A
N/A
u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in
whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or
any part thereof without the express permission of u-blox is strictly prohibited.
The information contained herein is provided “as is” and u-blox assumes no liability for the use of the information. No warranty, either
express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose
of the information. This document may be revised by u-blox at any time. For most recent documents, visit www.u-blox.com.
Copyright © 2016, u-blox AG.
u-blox® is a registered trademark of u-blox Holding AG in the EU and other countries. ARM® is the registered trademark of ARM Limited in
the EU and other countries.
UBX-16015271 - R03
Product Information
Page 2 of 46
EMMY-W1 series - User Manual
Contents
Contents.............................................................................................................................. 3
Functional description.................................................................................................. 5
1.1
Overview .............................................................................................................................................. 5
1.2
1.3
Applications .......................................................................................................................................... 5
Product features ................................................................................................................................... 6
1.4
Block diagrams ..................................................................................................................................... 6
1.5
1.6
Product description ............................................................................................................................... 7
Supported features ............................................................................................................................... 8
1.6.1
Wi-Fi features ................................................................................................................................ 8
1.6.2
1.6.3
Bluetooth features ......................................................................................................................... 8
NFC features ................................................................................................................................. 8
1.6.4
General product features ............................................................................................................... 8
1.6.5
Compliance ................................................................................................................................... 9
1.7
Additional reserved MAC addresses ...................................................................................................... 9
Interfaces .................................................................................................................... 10
2.1
2.2
Operation mode configuration ........................................................................................................... 10
SDIO interface .................................................................................................................................... 10
2.2.1
Default speed and High speed modes ......................................................................................... 10
2.2.2
2.2.3
SDR12, SDR25, SDR50 Modes (up to 100 MHz) (1.8 V) ............................................................... 11
SDR104 Mode (208 MHz) (1.8 V) ................................................................................................ 12
2.2.4
DDR50 Mode (50 MHz) (1.8 V) .................................................................................................... 13
2.3
2.4
High Speed UART interface ................................................................................................................. 14
PCM interface ..................................................................................................................................... 15
2.4.1
2.5
PCM interface specifications ........................................................................................................ 15
GPIO interface .................................................................................................................................... 16
Pin Definition .............................................................................................................. 18
3.1
Pin description .................................................................................................................................... 18
3.2
Reset configuration............................................................................................................................. 19
Electrical specification ................................................................................................ 20
4.1
Absolute maximum ratings ................................................................................................................. 20
4.2
4.3
Operating conditions .......................................................................................................................... 20
Digital pin ratings ............................................................................................................................... 21
4.4
Wi-Fi power consumption ................................................................................................................... 21
4.5
4.6
Bluetooth power consumption ........................................................................................................... 22
NFC power consumption .................................................................................................................... 22
4.7
Radio specifications ............................................................................................................................ 23
4.7.1
4.7.2
Wi-Fi ........................................................................................................................................... 23
Bluetooth .................................................................................................................................... 28
UBX-16015271 - R03
Product Information
Contents
Page 3 of 46
EMMY-W1 series - User Manual
4.7.3
4.7.4
LTE co-existence .......................................................................................................................... 28
Near field communication ........................................................................................................... 28
Host drivers and firmware ......................................................................................... 30
5.1
5.2
General principle ................................................................................................................................ 30
Supported operating systems .............................................................................................................. 30
5.2.1
Linux ........................................................................................................................................... 30
Mechanical specifications .......................................................................................... 31
Qualification and approvals ...................................................................................... 32
7.1
Approvals ........................................................................................................................................... 32
7.1.1
European Union regulatory compliance ....................................................................................... 32
7.1.2
FCC compliance .......................................................................................................................... 33
7.1.3
IC compliance.............................................................................................................................. 34
7.2
Approved antennas ............................................................................................................................ 35
7.2.1
Bluetooth antenna ...................................................................................................................... 36
7.2.2
NFC antenna ............................................................................................................................... 36
7.3
FCC and IC IDs (planned) .................................................................................................................... 36
7.4
Certification in other countries ........................................................................................................... 36
Product handling ........................................................................................................ 37
8.1
Packaging ........................................................................................................................................... 37
8.1.1
Reels ........................................................................................................................................... 37
8.1.2
Tapes .......................................................................................................................................... 37
8.2
Shipment, storage and handling ......................................................................................................... 37
8.2.1
Moisture sensitivity levels ............................................................................................................. 37
8.2.2
8.2.3
Mounting process and soldering recommendations ..................................................................... 38
ESD handling precautions ............................................................................................................ 39
Labeling and ordering information........................................................................... 40
9.1
9.2
Product labeling.................................................................................................................................. 40
Explanation of codes........................................................................................................................... 41
9.3
Ordering codes ................................................................................................................................... 41
Appendix .......................................................................................................................... 42
A Glossary ...................................................................................................................... 42
Related documents........................................................................................................... 44
Revision history ................................................................................................................ 45
Contact .............................................................................................................................. 46
UBX-16015271 - R03
Product Information
Contents
Page 4 of 46
EMMY-W1 series - User Manual
1 Functional description
1.1 Overview
The EMMY-W1 series provides a complete short range transceiver solution that can easily be integrated into
automotive and industrial applications. The modules are designed for both simultaneous and independent
operation of the following technologies:
 IEEE 802.11a/b/g/n/ac payload data rates for Wi-Fi
 Dual-mode Bluetooth v4.2
 NFC
The EMMY-W1 series is a surface-mount device (SMD) component and can be used as a Wi-Fi micro-access point
supporting up to 10 clients. A coexistence feature on chip level improves parallel use of Bluetooth and Wi-Fi
communication. For highest throughput and performance, a module variant with separated Wi-Fi and Bluetooth
antenna pin is also available.
The modules include an integrated MAC/baseband processor and RF front-end components and can connect to
a host processor through SDIO 3.0 and high-speed UART interfaces. The EMMY-W1 series are offered in
automotive and professional grades (see 9.3 Ordering codes and 1.4 Block diagrams). The automotive grade
variant includes an automotive-qualified (AEC-Q100) chipset. A host driver for Linux 3.x is available free of
charge. The modules are radio type approved for Europe (ETSI R&TTE), US (FCC CFR 47 part 15 unlicensed
modular transmitter approval) and Canada (IC RSS). Regulatory approvals for using this module in Japan, South
Korea, China, Taiwan and Australia will follow.
1.2 Applications
Automotive applications
 High definition (HD) video streaming (headrest displays, rear-view camera) and in-car gaming
 Rapid sync-n-go applications and fast content download to the vehicle
 Hands-free equipment (Bluetooth)
 Personalized adjustment of comfort functions through NFC
Industrial applications




Manufacturing floor automation, wireless control terminals and point-to-point backhaul
Outdoor content distribution
Mobile video streaming
Robust wireless connectivity in a broad range of industrial applications
Approvals are pending
UBX-16015271 - R03
Product Information
Functional description
Page 5 of 46
EMMY-W1 series - User Manual
1.3 Product features
Power supply: 3.0-3.6 V
Solder pins
Micro Access Point
AES hardware support
RF parameters in OTP memory
MAC addresses in OTP memory
•
•
•
v4.2 H 18 dBm 2p
•
•
•
•
•
•
•
•
•
v4.2 H 18 dBm 1p
•
•
•
•
•
•
•
•
•
•
v4.2 H 18 dBm 1p
EMMY-W163
•
•
a/b/g/n/ac
•
EMMY-W165
•
•
a/b/g/n/ac
•
Bluetooth profiles
a/b/g/n/ac
Bluetooth qualification
•
Automotive
SDIO 3.0
•
•
Professional
High-speed UART
•
Antenna type
•
NFC
•
Wi-Fi IEEE 802.11 version
•
Wi-Fi 5 GHz channels 36-165
•
Wi-Fi 2.4 GHz channels 1-13
LTE filter
Max output power at antenna pin
Grade
•
EMMY-W161
H = HCI
Features
Power Connectors
Standard
Interfaces
Radio
PCM (Bluetooth audio)
Model
1p = One pin for combined external antenna for Bluetooth and Wi-Fi
2p = Two pins for separate external antennas for Bluetooth and Wi-Fi
Table 1: EMMY-W1 series main features summary
1.4 Block diagrams
The block diagrams of the EMMY-W1 series are provided in this section.
EMMY-W161 / EMMY-W165
5GHz BPF &
DIPLEXER
5GHz WLAN TX/RX
SDIO
VIO1
UART
VIO2
WLAN &
BT ANT
2.4GHz WLAN TX
2.4GHz WLAN/BT RX
PCM
VIO2
BT LTE
COEX
VIO2
GPIOs
VIO2
MAC/BB/RADIO
2.4GHz
BPF
SP3T
BT TX
BT LED
NFC
COIL
WLAN
LED
PDn
37.4 MHz
Crystal
3.3V
DC/DC
3.3V
VIO1
1.8V
1.1V
VIO2
GND
Figure 1: EMMY-W161/EMMY-W165 block diagram - Single antenna variant
UBX-16015271 - R03
Product Information
Functional description
Page 6 of 46
EMMY-W1 series - User Manual
In EMMY-W161, the band pass filter (2.4 GHz BPF) is a BAW filter that enables co-existence with
LTE. For the variant EMMY-W165, the band pass filter provides no co-existence protection against
a co-located LTE transmitter.
EMMY-W163
5GHz BPF &
DIPLEXER
5GHz WLAN TX/RX
SDIO
VIO1
UART
VIO2
2.4GHz WLAN TX
2.4GHz WLAN RX
PCM
VIO2
BT LTE
COEX
VIO2
GPIOs
VIO2
WLAN
ANT
MAC/BB/RADIO
BT RX/TX
2.4GHz
BPF
SP3T
2.4GHz
BPF
BT
ANT
BT LED
NFC
COIL
WLAN
LED
37.4 MHz
Crystal
PDn
3.3V
DC/DC
3.3V
VIO1
1.8V
1.1V
VIO2
GND
Figure 2: EMMY-W163 block diagram - Dual-antenna variant
In EMMY-W163, the bandpass filters (2.4 GHz BPF) are ceramic bandpass filters. An LTE co-existence
variant is not available in the dual-antenna configuration.
1.5 Product description
Model
Description
EMMY-W161
Professional grade module with 1 combined antenna pin for Wi-Fi and Bluetooth and integrated LTE filter
EMMY-W163
EMMY-W165
Professional grade module with 2 separate antenna pins for Wi-Fi and Bluetooth (no LTE filter)
Professional grade module with 1 combined antenna pin for Wi-Fi and Bluetooth (no LTE filter)
EMMY-W161-A
EMMY-W163-A
Automotive grade module with 1 combined antenna pin for Wi-Fi and Bluetooth and integrated LTE filter
Automotive grade module with 2 separate antenna pins for Wi-Fi and Bluetooth (no LTE filter)
EMMY-W165-A
Automotive grade module with 1 combined antenna pin for Wi-Fi and Bluetooth (no LTE filter)
The EMMY-W161 is recommended for applications that have co-located Wi-Fi, Bluetooth and LTE
antennas and require co-existence of these wireless technologies. This module provides a dedicated BAW
bandpass filter instead of the ceramic bandpass filter. This filter rejects the adjacent LTE bands B40, B7,
B41 and B38. The integrated BAW filter is available only for the single-antenna configuration
(EMMY-W161). The module pinout, operating conditions, and electrical characteristics are identical for all
product variants. Differences in the RF parameters are explained in the Radio specifications section.
UBX-16015271 - R03
Product Information
Functional description
Page 7 of 46
EMMY-W1 series - User Manual
1.6 Supported features
1.6.1 Wi-Fi features








Wi-Fi standards: IEEE 802.11a/b/g/n/ac/d/e/h/i/k /r/v /w
Simultaneous client and access point operation (up to 10 clients supported)
Support of Wi-Fi direct mode
IEEE 802.11ac 1x1 antenna configuration
IEEE 802.11 PHY data rates up to 433 Mbps
64- and 128-bit AES hardware encryption engine
WAPI encryption is supported by hardware
SDIO 3.0 host interface for Wi-Fi
1.6.2 Bluetooth features



Bluetooth v4.2 with Bluetooth Low Energy and Classic Bluetooth v2.1+EDR over SDIO or high-speed
UART interface
PCM interface for audio
MWS/LTE coexistence serial transport interface for connecting an external and co-located LTE device
1.6.3 NFC features












NCI 1.0 support according to NFC Forum specification
NFC support through SDIO or UART
Full protocol support for ISO 14443A/B, ISO 15693 , ISO 18092, NFCIP-2, NFC forum, EMV contactless
targets with data rates up to 848 Kbps
Deep Sleep
Proprietary Low-Power Target Detection mode to reduce standby current consumption
On-Host card emulation: supported in NFC A, B, F and V technologies
Off-Host card emulation with UICCs and Embedded SEs (availability is package dependent):
o ETSI TS 102 613: SWP/CLT ISO14443 Type A (Mifare) and ISO18093 212/424 kbps passive
mode (FeliCa).
o ETSI TS 102 622: SWP/HCI ISO14443A/B and ISO18092 212/424 kbps passive mode
o DCLB
Compliant with EMVCo book D (Contactless Communication Protocol)
Reader/Writer, card emulation, and Peer-to-peer (P2P) modes
Programmable carrier detection level for card emulation mode
Programmable field detection level for RF anti-collision when operating as reader or active target
UART host interface support (shared with Bluetooth when operating)
1.6.4 General product features






Driver support for Linux
Low-power and sleep modes for Bluetooth and Wi-Fi core
Coexistence arbitration for Wi-Fi/Bluetooth/LE/NFC/LTE operation
Small footprint (19.8 mm x 13.8 mm), LGA package
Product variant with integrated LTE co-location filter available
Automotive qualification tests (climatic, mechanical, and operating life tests) according ISO 16750-4
planned
Supported by hardware but not supported by firmware currently.
Available on request
For ISO 15693 VICC mode, the maximum supported 10-90% rise/fall times for receiving 10% ASK modulation is 1.18 μs.
UBX-16015271 - R03
Product Information
Functional description
Page 8 of 46
EMMY-W1 series - User Manual
1.6.5 Compliance


RoHS compliant
Radio type approvals for Europe, USA, Canada, Japan, Korea, Taiwan, China and Australia
1.7 Additional reserved MAC addresses
The EMMY-W1 module series has four unique consecutive MAC addresses reserved for each module, from
which the first two addresses are already stored in the configuration during production. The first address is used
for the Bluetooth communication while the second address is configured for Wi-Fi communication. The Data
Matrix Code on the label includes the Bluetooth MAC address (see section 9). The remaining two MAC
addresses are not used in the manufacturing configuration, but are reserved for usage with the module.
MAC address
Assignment
Last two bits of MAC address
Example
Module1, address 1
Bluetooth
0b00
D4:CA:6E:44:00:04
Module1, address 2
Wi-Fi
0b01
D4:CA:6E:44:00:05
Module1, address 3
(free for use)
0b10
D4:CA:6E:44:00:06
Module1, address 4
(free for use)
0b11
D4:CA:6E:44:00:07
Module2, address 1
Bluetooth
0b00
D4:CA:6E:44:00:08
Module2, address 2
Wi-Fi
0b01
D4:CA:6E:44:00:09
Module2, address 3
(free for use)
0b10
D4:CA:6E:44:00:0A
Module2, address 4
(free for use)
0b11
D4:CA:6E:44:00:0B
Table 2: MAC address assignment
Approvals are pending.
UBX-16015271 - R03
Product Information
Functional description
Page 9 of 46
EMMY-W1 series - User Manual
2 Interfaces
2.1
Operation mode configuration
EMMY-W1 series module uses the GPIO_3 and GPIO_2 pins as host interface configuration input to set the
desired operation mode following a reset. The definitions of these pins are changed to their usual functions after
reset. When you need to configure the pins for a certain module operation mode, you need to provide a 100 kΩ
pull down resistor to the ground. No external circuitry is required to set a configuration pin to high logical level.
External reset is not needed for proper operation due to internal power-up reset logic though it can be used by
the host controller through the PDn pin (active low) in case of an abnormal module behavior.
After reset, GPIO_3 and GPIO_2 pins can be used as open drain outputs (depending on firmware/driver version)
for Bluetooth and Wi-Fi activity LED indicators, but simultaneous usage of an LED connected to 3.3 V power line
and a pull-down resistor is not allowed (LED acts as a strong pull-up circuitry). Do not connect LED if you need
the pull-down resistors.
Depending on the firmware or driver used, you can use either one or both host interface operation modes:
GPIO_3
GPIO_2
Wi-Fi
Bluetooth/NFC
Number of SDIO functions
SDIO
UART
1 (Wi-Fi)
SDIO
SDIO
3 (Wi-Fi, Bluetooth and NFC)
SDIO
SDIO
UART
SDIO
1 (Wi-Fi)
3 (Wi-Fi, Bluetooth and NFC)6
Table 3: Module configuration
2.2
SDIO interface
EMMY-W1 series modules support an SDIO device interface that conforms to the industry standard SDIO 3.0
Full-Speed specification (4-bit SDIO up to 208 MHz) and allows a host controller using the SDIO bus protocol to
access the Wi-Fi and Bluetooth functions. The interface supports 4-bit SDIO transfer mode at the full clock range
of 0 to 208 MHz.
2.2.1 Default speed and High speed modes
Figure 3: SDIO protocol timing diagram- Default speed mode (3.3 V)
Default configuration. It is possible to use connected LEDs to both the pins.
UBX-16015271 - R03
Product Information
Interfaces
Page 10 of 46
EMMY-W1 series - User Manual
Figure 4: SDIO protocol timing diagram – High speed mode (3.3 V)
Symbol
Parameter
Condition
Min.
Typ
Max.
Units
fPP
Clock frequency
Normal
25
MHz
TWL
Clock low time
High speed
Normal
10
50
MHz
ns
High speed
ns
TWH
Clock high time
Normal
High speed
10
ns
ns
TISU
Input setup time
Normal
High speed
ns
ns
TIH
Input hold time
Normal
High speed
ns
ns
TODLY(max)
TODLY(min)
Maximal Output delay time
Minimal Output delay time
Normal
Normal
14
ns
ns
TODLY
Output delay time CL ≤ 40 pF
(1 card)
Output hold time
Normal
14
ns
ns
TOH
High speed
2.5
Table 4: SDIO timing data – Default speed, High speed modes (3.3 V)
2.2.2 SDR12, SDR25, SDR50 Modes (up to 100 MHz) (1.8 V)
Figure 5: SDIO protocol timing diagram – SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8 V)
UBX-16015271 - R03
Product Information
Interfaces
Page 11 of 46
EMMY-W1 series - User Manual
Symbol
Parameter
Condition
Min.
Typ
Max.
Units
fPP
Clock frequency
SDR12/25/50
25
100
MHz
TIS
TIH
Input setup time
Input hold time
SDR12/25/50
SDR12/25/50
0.8
ns
ns
TCLK
Clock time
SDR12/25/50
10
40
ns
TCR, TCF,
Rise time, fall time
TCR, TCF < 2 ns (max) at 100 MHz
CCARD = 10 pF
Output delay time
CL ≤ 30 pF
Output hold time
CL = 15 pF
SDR12/25/50
0.2*TCLK
ns
SDR12/25/50
7.5
ns
ns
TODLY
TOH
SDR12/25/50
1.5
Table 5: SDIO timing data – SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8 V)
2.2.3 SDR104 Mode (208 MHz) (1.8 V)
Figure 6: SDIO protocol timing diagram – SDR104 mode (208 MHz)
Symbol
Parameter
Condition
Min.
Typ
Max.
Units
fPP
TIS
Clock frequency
Input setup time
SDR104
SDR104
1.4
208
MHz
ns
TIH
TCLK
Input hold time
Clock time
SDR104
SDR104
0.8
4.8
ns
ns
TCR, TCF,
Rise time, fall time
TCR, TCF < 0.96 ns (max) at 208 MHz
CCARD = 10 pF
SDR104
0.2*TCLK
ns
TOP
TODW
Card output phase
Output timing of variable data window
SDR104
SDR104
10
ns
ns
2.88
Table 6: SDIO timing data – SDR104 mode (208 MHz)
UBX-16015271 - R03
Product Information
Interfaces
Page 12 of 46
EMMY-W1 series - User Manual
2.2.4 DDR50 Mode (50 MHz) (1.8 V)
Figure 7: SDIO CMD timing diagram – DDR50 mode (50 MHz)
Figure 8: SDIO DAT[3:0] timing diagram – DDR50 mode (50 MHz)
UBX-16015271 - R03
Product Information
Interfaces
Page 13 of 46
EMMY-W1 series - User Manual
Symbol
Parameter
Condition
Min.
Clock time
50 MHz (max) between rising edges
Rise time, fall time
TCR, TCF < 4.00 ns (max) at 50 MHz
CCARD = 10 pF
DDR50
20
Typ
Max.
Units
Clock
TCLK
TCR, TCF,
ns
DDR50
Clock Duty
CMD Input (referenced to clock rising edge)
TIS
Input setup time
CCARD ≤ 10 pF (1 card)
TIH
Input hold time
CCARD ≤ 10 pF (1 card)
0.2*TCLK
ns
55
DDR50
45
DDR50
ns
DDR50
0.8
ns
CMD Output (referenced to clock rising edge)
TODLY
Output delay time during data transfer mode
DDR50
CL ≤ 30 pF (1 card)
TOHLD
Output hold time
DDR50
CL ≥ 15 pF (1 card)
DAT[3:0] Input (referenced to clock rising and falling edges)
TIS2x
Input setup time
DDR50
CCARD ≤ 10 pF (1 card)
TIH2x
Input hold time
DDR50
CCARD ≤ 10 pF (1 card)
DAT[3:0] Output (referenced to clock rising and falling edges)
TODLY2x (max)
Output delay time during data transfer mode
DDR50
CL ≤ 25 pF (1 card)
TODLY2x (min)
Output hold time
DDR50
CL ≥ 15 pF (1 card)
13.7
ns
1.5
ns
ns
0.8
ns
7.0
1.5
ns
ns
Table 7: SDIO timing data – DDR50 mode (50 MHz)
2.3 High Speed UART interface
The EMMY-W1 series modules support a high speed Universal Asynchronous Receiver/Transmitter (UART)
interface in compliance with the industry standard 16550 specification. The main features of the UART interface
are:





FIFO mode permanently selected for transmit and receive operations
2 pins for transmit and receive operations
2 flow control pins
Interrupt triggers for low-power, high throughput operation
High throughput (4 Mbps)
The UART interface operation includes:


Uploading the firmware to the module
Supporting data input/output operation for peripheral devices connected through a standard UART
interface
Baud Rate
1200
38400
460800
1500000
3000000
2400
4800
57600
76800
500000
921600
1843200
2000000
3250000
3692300
9600
19200
115200
230400
1000000
1382400
2100000
2764800
4000000
Table 8: Supported UART Baud rates
UBX-16015271 - R03
Product Information
Interfaces
Page 14 of 46
EMMY-W1 series - User Manual
2.4 PCM interface
The EMMY-W1 series modules support a Pulse Code Modulation (PCM) interface that provides:




Master or slave mode
PCM bit width size of 8 bits or 16 bits
Up to 4 slots with configurable bit width and start positions
Short frame and long frame synchronization
2.4.1 PCM interface specifications
Figure 9: PCM timing specification – Master mode
Symbol
Parameter
Condition
Min.
Typ
Max.
Units
FBCLK
2/2.048
MHz
Duty Cycle BCLK
TBCLK rise/fall
0.4
0.5
0.6
Ns
TDO
15
ns
TDISU
TDIHO
20
15
ns
ns
TBF
15
ns
Table 9: PCM timing specification – Master mode
UBX-16015271 - R03
Product Information
Interfaces
Page 15 of 46
EMMY-W1 series - User Manual
Figure 10: PCM timing specification – Slave mode
Symbol
Parameter
Condition
Min.
Typ
Max.
Units
FBCLK
2/2.048
MHz
Duty Cycle BCLK
TBCLK rise/fall
0.4
0.5
0.6
ns
TDO
30
ns
TDISU
TDIHO
15
10
ns
ns
TBFSU
TBFHO
15
10
ns
ns
Table 10: PCM timing specification – Slave mode
2.5 GPIO interface
The General-Purpose I/O (GPIO) interface is used to implement user defined input and output signals to and from
the 88W8887 chip such as external interrupts and other user-defined I/Os. Main features of the GPIO interface
include:



User-defined GPIO (each I/O configured to either input or output)
Each GPIO independently controlled
Each I/O configurable to output bit from GPIO_OUT
The general functions associated with each GPIO pin is shown in Table 11:
UBX-16015271 - R03
Product Information
Interfaces
Page 16 of 46
EMMY-W1 series - User Manual
GPIOP Pin
10
11
12
13
14
15
16
17
Input
Output
GPIO
Function
General
LEDs
LED output7
Interrupts
Input
Table 11: GPIO Functions – GPIO [17:14], [12:0]
GPIO_12 is not available.
GPIO [2] is used for Wi-Fi activity while GPIO [3] is used for Bluetooth activity.
UBX-16015271 - R03
Product Information
Interfaces
Page 17 of 46
EMMY-W1 series - User Manual
3 Pin Definition
GND
SD_CLK
SD_CMD
SD_D0
SD_D1
SD_D2
SD_D3
GND
GND
3V3
VIO1
VIO2
PDn
GPIO_8
GPIO_9
GPIO_10
GPIO_11
GPIO_3
GPIO_2
GND
NFC_ANT_N
NFC_ANT_P
GND
EMMY-W1
GND
ANT1
GND
GND
GND
GND
ANT2
GND
46
45
44
43
42
41
40
39
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
16
17
18
19
20
21
22
23
GND
GPIO_7
GPIO_6
GPIO_5
GPIO_4
GPIO_17
GPIO_16
GPIO_15
GPIO_14
GPIO_1
GPIO_0
Reserved
Reserved
Reserved
GND
15
14
13
12
11
10
3.1 Pin description
Figure 11: Pin assignment
No
Pin name
Pin type
Supply domain
Description
GND
Ground
Ground
NC
Reserved, do not connect
NC
Reserved, do not connect
NC
Reserved, do not connect
GPIO_0
I/O
VIO2
BT2HOST_WAKEUP (Output)
GPIO_1
I/O
VIO2
WL2HOST_WAKEUP (Output)
GPIO_14
I/O
VIO2
HOST2WL_WAKEUP (Input)
GPIO_15
I/O
VIO2
HOST2BT_WAKEUP (Input)
GPIO_16
I/O
VIO2
UART_LTE_SIN (Input)
10
GPIO_17
I/O
VIO2
UART_LTE_SOUT (Output)
11
GPIO_4
I/O
VIO2
PCM_DIN (Input)
12
GPIO_5
I/O
VIO2
PCM_DOUT (Output)
13
GPIO_6
I/O
VIO2
PCM_CLK (Input if slave, Output if master)
14
GPIO_7
I/O
VIO2
PCM_SYNC (Input if slave, Output if master)
15
GND
Ground
Ground
16
GND
Ground
Ground
17
SD_CLK
VIO1
SDIO Clock input
18
SD_CMD
I/O
VIO1
SDIO Command line
19
SD_D0
I/O
VIO1
SDIO Data line bit [0]
20
SD_D1
I/O
VIO1
SDIO Data line bit [1]
21
SD_D2
I/O
VIO1
SDIO Data line bit [2]
22
SD_D3
I/O
VIO1
SDIO Data line bit [3]
UBX-16015271 - R03
Product Information
Pin Definition
Page 18 of 46
EMMY-W1 series - User Manual
No
Pin name
Pin type
Supply domain
Description
23
GND
Ground
Ground
24
GND
Ground
Ground
25
3V3
Power
3.3V
3.3V Power supply (2.97 V - 3.63 V)
26
VIO1
Power
VIO1
VIO1 Power supply (1.62V - 1.98 V, 2.97 V - 3.63 V)
27
VIO2
Power
VIO2
VIO2 Power supply (1.62V - 1.98 V, 2.97 V - 3.63 V)
28
PDn
Input
Full power down(active low)8
29
GPIO_8
I/O
VIO2
UART_SOUT (Output)
30
GPIO_9
I/O
VIO2
UART_SIN (Input)
31
GPIO_10
I/O
VIO2
UART_CTSn (Input)
32
GPIO_11
I/O
VIO2
UART_RTSn (Output)
33
GPIO_3
I/O
3.3V
LED_OUT_BT (Output) - BT indicator, Configuration pin9
34
GPIO_2
I/O
3.3V
LED_OUT_WLAN (Output) - WLAN indicator, Configuration pin9
35
GND
Ground
Ground
36
NFC_ANT_N
I/O, RF
3.3V
NFC Coil Antenna, negative I/O pin
37
NFC_ANT_P
I/O, RF
3.3V
NFC Coil Antenna, positive I/O pin
38
GND
Ground
Ground
39
GND
Ground
Ground
40
ANT2
I/O, RF
Bluetooth antenna only in case of EMMY-W163 module. Not connected in
case of EMMY-W161 or EMMY-W165 module10
41
GND
Ground
Ground
42
GND
Ground
Ground
43
GND
Ground
Ground
44
GND
Ground
Ground
45
ANT1
I/O, RF
Wi-Fi + Bluetooth antenna in case of single-antenna module. Wi-Fi antenna
only in case of dual-antenna module10
46
GND
Ground
Ground
Exposed pin
Ground
Six Ground/Thermal exposed pins, connect to the ground
Table 12: EMMY-W1 series pin description
3.2 Reset configuration
The EMMY-W1 is reset to its default operating state under the following conditions:



Power-on reset (POR) – Module receives power 3V3 supplies rise (triggers internal POR circuit)
Software/Firmware reset
External pin assertion (PDn) will generate POR.
High input impedance pin for minimizing shutdown current consumption. The pin shall be driven by the host controller or/and connected
via 51 kΩ (or less) pull-up resistor to the 3.3 V supply rail.
Possible to use as an LED output depending on the firmware and driver version. In this case, the module pin acts as an open drain output
and the whole LED circuitry must be supplied from 3.3 V power line. A LED current limiting resistor should be used; maximum sink current to
the ground is 10 mA. These pins can also be used for host interface configuration. See Operation mode configuration section.
10
Pin protected from the static electricity by internal DC feed to the ground.
UBX-16015271 - R03
Product Information
Pin Definition
Page 19 of 46
EMMY-W1 series - User Manual
4 Electrical specification
Stressing the device above one or more of the ratings listed in the Absolute Maximum Rating
section may cause permanent damage. These are stress ratings only. Operating the module at
these or at any conditions other than those specified in the Operating conditions section
(section 4.2) of the specification should be avoided. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Operating condition ranges define those limits within which the functionality of the device is guaranteed.
Where application information is given, it is advisory only and does not form part of the specification.
4.1 Absolute maximum ratings
Symbol
Description
Min.
Typ
Max.
Units
3V3
Power supply voltage 3.3 V
3.3
4.0
VIO1
I/O supply voltage 1.8 V
I/O supply voltage 3.3 V
1.8
3.3
2.2
4.0
VIO2
I/O supply voltage 1.8 V
1.8
2.2
3.3
TSTORAGE
I/O supply voltage 3.3 V
Storage temperature
4.0
+85
ºC
-40
Table 13: Absolute maximum ratings
The product is not protected against overvoltage or reversed voltages. If necessary, voltage
spikes exceeding the power supply voltage specification given in table above must be limited to
values within the specified boundaries by using appropriate protection devices.
4.2 Operating conditions
Symbol
Parameter
Min.
Typ
Max.
Units
3V3
Power supply voltage 3.3 V
2.97
3.3
3.63
VIO1
I/O supply voltage 1.8V/3.3 V
1.62
2.97
1.8
3.3
1.98
3.63
VIO2
I/O supply voltage 1.8V/3.3 V
1.62
2.97
1.8
3.3
1.98
3.63
VDD_NFC
IANT_NFC
NFC antenna input voltage (pins NFC_ANT_P/N)
NFC antenna peak input current (pins NFC_ANT_P/N))
3.6
400
mA
TA
Ambient operating temperature
-40
+85
ºC
Ripple Noise
Peak-to-peak voltage ripple on 3V3, VIO1 or VIO2
supply line. The values have been determined in a
frequency range from 10 KHz to > 2 MHz [3].
20
mV
Table 14: Operating conditions
Parameter
Min.
Max.
Units
Storage temperature
-40
Typ
+85
ºC
Operation temperature
-40
+85
ºC
Table 15: Temperature range
UBX-16015271 - R03
Product Information
Electrical specification
Page 20 of 46
EMMY-W1 series - User Manual
4.3 Digital pin ratings
Symbol
Parameter
Min.
Max.
Units
VIH
VIL
Input high voltage
Input low voltage
0.7*VIO
-0.4
VIO+0.4
0.3*VIO
VHYS
VOH
Input hysteresis
Output high voltage
100
VIO-0.4
mV
VOH
Output low voltage
0.4
Table 16: Digital pin ratings for VIO1 and VIO2 supply domains
4.4 Wi-Fi power consumption
Operation mode:
2.4 GHz Wi-Fi TX/RX with BT and NFC in Deep Sleep mode
Average current, mA11
Peak current, mA12
RX Idle Default
RX 11 Mbps
52
50
64
62
TX 11 Mbps (Normal power mode, 18 dBm)
TX 11 Mbps (Low power mode, 10 dBm)
290
184
420
RX 54 Mbps
TX 54 Mbps (15 dBm)
54
260
68
320
TX 54 Mbps (8 dBm)
RX 11n MCS7 (HT20)
170
65
TX 11n MCS7 (HT20, 15 dBm)
260
TX 11n MCS7 (HT20, 8 dBm)
174
Operation mode:
5 GHz Wi-Fi TX/RX with BT and NFC in Deep Sleep mode
Average current, mA11
Peak current, mA12
RX 54 Mbps
TX 54 Mbps (12 dBm)
67
280
75
320
TX 54 Mbps (8 dBm)
RX MCS7 (HT20)
196
78
TX MCS7 (HT20, 12 dBm)
TX MCS7 (HT20, 8 dBm)
282
202
RX MCS7 (HT40)
TX MCS7 (HT40, 10 dBm)
89
270
TX MCS7 (HT40, 8 dBm)
214
RX MCS7 (VHT80)
TX MCS7 (VHT80, 11 dBm)
112
360
RX MCS8 (VHT20)
TX MCS8 (VHT20, 11 dBm)
82
265
RX MCS8 (VHT40)
TX MCS8 (VHT40, 10 dBm)
105
265
RX MCS8 (VHT80)
114
TX MCS8 (VHT80, 8 dBm)
RX MCS9 (VHT40)
356
104
TX MCS9 (VHT40, 10 dBm)
RX MCS9 (VHT80)
263
120
TX MCS9 (VHT80, 8 dBm)
348
11
12
Supply 3.3V. Wi-Fi client mode. Numbers obtained from IPERF UDP traffic.
Maximum peak current for the worst supply conditions
UBX-16015271 - R03
Product Information
Electrical specification
Page 21 of 46
EMMY-W1 series - User Manual
Operation mode:
Power save modes
Power Down
Average current, mA
0.03
WiFi and BT both in Deepsleep
WiFi DTIM 1 and BT Deepsleep
0.13
1.14
WiFi DTIM 3 and BT Deepsleep
WiFi DTIM 5 and BT Deepsleep
0.47
0.34
Table 17: Wi-Fi power consumption
4.5 Bluetooth power consumption
Bluetooth mode with Wi-Fi and NFC in deep sleep mode
TX @ 0dBm
Deep Sleep Mode
Average current, mA13
0.125
BT idle (Sleep Mode)
Power Down
4.23
0.03
SCO HV3 Peak TX
SCO HV3 Peak RX
18.75
16.50
HV3 SCO mode ACL sniff 0x800
eSCO link, Master (2-EV3), ACL sniff 0x800
7.57
6.57
eSCO link, Master (EV3), ACL sniff 0x800
7.69
ACL (data pump) DH1
ACL (data pump) DH3
11.60
14.60
ACL (data pump) DH5
ACL Link, master sniff mode, interval=1.28s (800)
16.40
0.186
ACL Link, master sniff mode, interval=500ms (320)
SCO HV3 Average TX @ 4 dBm (external antenna)
0.278
7.83
SCO HV3 Average RX @ 4 dBm (external antenna)
Interlaced scan (= P&I scan)
22.00
0.372
Page & Inquiry scan
0.372
Page Scan
Inquiry Scan
0.257
0.257
LE Advertise @ 1.28s interval
Peak LE TX
0.150
18.00
Peak LE RX
LE Link (interval=400=1.28s)
16.00
0.154
LE Link (interval=320=1.00s)
0.155
LE Scan (interval=800=1.28s)
LE Scan (interval=640-1.00s)
0.231
0.262
Table 18: Bluetooth power consumption
4.6 NFC power consumption
Operation Mode
Average current, mA
3V3
TAG Type 1
TAG Type 2
90
95
TAG Type 3
85
TAG Type 4A
100
Table 19: NFC power consumption
13
Supply 3.3V, Average consumption current if not specified otherwise.
UBX-16015271 - R03
Product Information
Electrical specification
Page 22 of 46
EMMY-W1 series - User Manual
4.7 Radio specifications
4.7.1 Wi-Fi
The EMMY-W1 series modules support Wi-Fi standards IEEE 802.11a/b/g/n/ac in 2.4 GHz and 5 GHz radio
bands. In the 2.4 GHz band, the EMMY-W1 supports 802.11b/g/n while in 5 GHz band, it supports
802.11a/n/ac.
Parameter
RF Frequency range
Modulation
Supported data rates
Supported channel
bandwidth
Supported guard interval (GI)
Maximum transmit power
Receiver sensitivity
2.4 GHz
Operation Mode
Specification
802.11b/g/n
2.400 – 2.500 GHz
802.11a/n/ac
5.150 – 5.850 GHz
802.11b
802.11a/g/n/ac
CCK and DSSS
OFDM
802.11b
802.11a/g
1, 2, 5.5, 11 Mbps
6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n
802.11ac
MCS0 - MCS7 (150 Mbps)
MCS0 – MCS9 (433 Mbps)
802.11ac
20, 40, 80 MHz
802.11n
400, 800 ms
802.11ac
802.11b
Short guard interval supported
18 dBm ± 1.5 dB
802.11a/g/n/ac
802.11b
16 dBm ± 1.5 dB
-98 dBm ± 1 dB
1 Mbps
11 Mbps
802.11g
-91 dBm ± 1 dB
-74 dBm ± 1 dB
20 MHz
MCS0
MCS7
-91 dBm ± 1 dB
-73 dBm ± 1 dB
40 MHz
MCS0
MCS7
-89 dBm ± 1 dB
-71 dBm ± 1 dB
802.11a
6 Mbps
-91 dBm ± 1 dB
802.11n
20 MHz
54 Mbps
MCS0
-74 dBm ± 1 dB
-90 dBm ± 1 dB
40 MHz
MCS7
MCS0
-72 dBm ± 1 dB
-88 dBm ± 1 dB
80 MHz
MCS9
MCS0
-63 dBm ± 1 dB
-85 dBm ± 1 dB
MCS9
-60 dBm ± 1 dB
802.11n
5 GHz
-89 dBm ± 1 dB
6 Mbps
54 Mbps
802.11ac
Table 20: Wi-Fi radio specifications
Channel
Frequency, GHz
2.412
Channel
Frequency, GHz
2.437
Channel
11
Frequency, GHz
2.462
2.417
2.422
2.442
2.447
12
13
2.467
2.472
2.427
2.432
10
2.452
2.457
Table 21: 2.4 GHz Band Supported Channels, 20 MHz bandwidth
Channel
Frequency, GHz
Channel
Frequency, GHz
Channel
Frequency, GHz
1-5
2.422
4-8
2.437
7 - 11
2.452
2-6
2.427
5-9
2.442
3-7
2.432
6 - 10
2.447
Table 22: 2.4 GHz band supported channels, 40 MHz bandwidth
UBX-16015271 - R03
Product Information
Electrical specification
Page 23 of 46
EMMY-W1 series - User Manual
Channel
Frequency, GHz
Channel
Frequency, GHz
Channel
Frequency, GHz
36
5.180
100
5.500
144
5.720
40
5.200
104
5.520
149
5.745
44
5.220
108
5.540
153
5.765
48
5.240
112
5.560
157
5.785
52
5.260
116
5.580
161
5.805
56
5.280
132
5.660
165
5.825
60
5.300
136
5.680
64
5.320
140
5.700
Table 23: 5 GHz band supported channels, 20 MHz bandwidth
Channel
Frequency, GHz
Channel
Frequency, GHz
Channel
Frequency, GHz
36 - 40
5.190
100 - 104
5.510
149 - 153
5.755
44 - 48
5.230
108 - 112
5.550
157 - 161
5.795
52 - 56
5.270
132 - 136
5.670
60 - 64
5.310
140 - 144
5.710
Table 24: 5 GHz band supported channels, 40 MHz bandwidth
Channel
Frequency, GHz
Channel
Frequency, GHz
Channel
Frequency, GHz
42
5.210
106
5.530
155
5.775
58
5.290
138
5.690
Table 25: 5 GHz band supported channels, 80 MHz bandwidth
The module is certified to operate as both client and master on channels 1 - 13 (2412 - 2462
MHz), and channel 36 – 48 (5180 – 5240 MHz). On the following channels it is certified to
operate as a client only 52 – 64 (5260 – 5320 MHz), 100 – 116 (5500 – 5580 MHz), 132 – 140 (5660
– 5700 MHz) and 149 – 165 (5745 – 5825 MHz). When the module is set to operate on channels
52 – 64, 100 – 116, 132 – 140 and 149 – 165 it is restricted to only operate using passive scan.
The module is certified to operate with the power tables shown in Table 26 for operation in the
2.4 GHz band and from Table 27 to Table 29 for operation in the 5 GHz band. The specified
values are the maximum permitted output power settings.
UBX-16015271 - R03
Product Information
Electrical specification
Page 24 of 46
EMMY-W1 series - User Manual
Channel
Modulation
1-11
Data rates
Maximum power setting
CCK and DSSS
1, 2, 5.5, 11 Mbps
18 dBm
12
CCK and DSSS
1, 2, 5.5, 11 Mbps
15 dBm
13
CCK and DSSS
1, 2, 5.5, 11 Mbps
13 dBm (EMMY-W161),
12 dBm (EMMY-W163)
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
13 dBm
2-9
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
16 dBm
10
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
15 dBm
11
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
13 dBm
12
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
10 dBm
13
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
9 dBm (EMMY-W161),
8 dBm (EMMY-W163)
1-11
OFDM
20 MHz
48, 54 Mbps
13 dBm
12-13
OFDM
20 MHz
48, 54 Mbps
9 dBm
OFDM
20 MHz
HT20 MCS0-MCS4
13 dBm
OFDM
20 MHz
HT20 MCS0-MCS4
15 dBm
3-10
OFDM
20 MHz
HT20 MCS0-MCS4
16 dBm
11
OFDM
20 MHz
HT20 MCS0-MCS4
12 dBm
12-13
OFDM
20 MHz
HT20 MCS0-MCS4
9 dBm
1-10
OFDM
20 MHz
HT20 MCS5-MCS7
13 dBm
11
OFDM
20 MHz
HT20 MCS5-MCS7
12 dBm
12-13
OFDM
20 MHz
HT20 MCS5-MCS7
9 dBm (EMMY-W161),
8 dBm (EMMY-W163)
3 (2.422 GHz), 4 (2.427 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
11 dBm (EMMY-W161),
10 dBm (EMMY-W163)
5 (2.432 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
13 dBm
6 (2.437 GHz), 7 (2.442 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
14 dBm
8 (2.447 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
13 dBm
9 (2.452 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
10 dBm
3 (2.422 GHz), 4 (2.427 GHz)
OFDM
40 MHz
HT40 MCS5-MCS7
11 dBm
5 (2.432 GHz), 6 (2.437 GHz), OFDM
7 (2.442 GHz), 8 (2.447 GHz)
40 MHz
HT40 MCS5-MCS7
13 dBm
9 (2.452 GHz)
40 MHz
HT40 MCS5-MCS7
11 dBm
OFDM
Channel bandwidth
Table 26: WLAN power table for operation in the 2.4 GHz band
UBX-16015271 - R03
Product Information
Electrical specification
Page 25 of 46
EMMY-W1 series - User Manual
Channel
Modulation
Channel bandwidth
Data rates
Maximum power setting
36, 64
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
13 dBm
40, 44, 48, 52, 56, 60
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
16 dBm
36, 40, 44, 48, 52, 56, 60, 64
OFDM
20 MHz
48, 54 Mbps
13 dBm
36, 64
OFDM
20 MHz
HT20 MCS0-MCS4
13 dBm
40, 44, 48, 52, 56, 60
OFDM
20 MHz
HT20 MCS0-MCS4
16 dBm
36, 40, 44, 48, 52, 56, 60, 64
OFDM
20 MHz
HT20 MCS5-MCS7
13 dBm
36, 64
OFDM
20 MHz
VHT20 MCS0-MCS4
13 dBm
40, 44, 48, 52, 56, 60
OFDM
20 MHz
VHT20 MCS0-MCS4
16 dBm
36, 40, 44, 48, 52, 56, 60, 64
OFDM
20 MHz
VHT20 MCS5-MCS8
13 dBm
38 (5.190 GHz), 62 (5.310 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
12 dBm
46 (5.230 GHz), 54 (5.270 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
16 dBm
38 (5.190 GHz), 46 (5.230 GHz),
54 (5.270 GHz) , 62 (5.310 GHz)
OFDM
40 MHz
HT40 MCS5-MCS7
12 dBm (ELLA-W161),
11 dBm (ELLA-W163)
38 (5.190 GHz), 62 (5.310 GHz)
OFDM
40 MHz
VHT40 MCS0-MCS4
12 dBm
46 (5.230 GHz), 54 (5.270 GHz)
OFDM
40 MHz
VHT40 MCS0-MCS4
16 dBm
38 (5.190 GHz), 46 (5.230 GHz),
54 (5.270 GHz) , 62 (5.310 GHz)
OFDM
40 MHz
VHT40 MCS5-MCS7
12 dBm
38 (5.190 GHz), 46 (5.230 GHz),
54 (5.270 GHz) , 62 (5.310 GHz)
OFDM
40 MHz
VHT40 MCS8-MCS9
10 dBm
42 (5.210 GHz), 58 (5.290 GHz)
OFDM
80 MHz
VHT80 MCS0-MCS9
8 dBm
Table 27: WLAN power table for operation in the 5 GHz U-NII-1 and U-NII-2A bands
Channel
Modulation
Channel bandwidth
Data rates
Maximum power setting
100, 140
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
13 dBm
104-136 (exc. 120-128)
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
16 dBm
100-140 (exc. 120-128)
OFDM
20 MHz
48, 54 Mbps
13 dBm
100, 140
OFDM
20 MHz
HT20 MCS0-MCS4
13 dBm
104-136 (exc. 120-128)
OFDM
20 MHz
HT20 MCS0-MCS4
16 dBm
100-140 (exc. 120-128)
OFDM
20 MHz
HT20 MCS5-MCS7
13 dBm
100
OFDM
20 MHz
VHT20 MCS0-MCS4
13 dBm
104-144 (exc. 120-128)
OFDM
20 MHz
VHT20 MCS0-MCS4
16 dBm
100-144 (exc. 120-128)
OFDM
20 MHz
VHT20 MCS5-MCS8
13 dBm
102 (5.510 GHz), 134 (5.670 GHz) OFDM
40 MHz
HT40 MCS0-MCS4
12 dBm
110 (5.550 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
16 dBm
102 (5.510 GHz), 110 (5.550 GHz) OFDM
134 (5.670 GHz)
40 MHz
HT40 MCS5-MCS7
12 dBm
102 (5.510 GHz)
OFDM
40 MHz
VHT40 MCS0-MCS4
12 dBm
110 (5.550 GHz), 134 (5.670 GHz), OFDM
40 MHz
VHT40 MCS0-MCS4
16 dBm
UBX-16015271 - R03
Product Information
Electrical specification
Page 26 of 46
EMMY-W1 series - User Manual
Channel
Modulation
Channel bandwidth
Data rates
Maximum power setting
102 (5.510 GHz), 110 (5.550 GHz), OFDM
134 (5.670 GHz), 142 (5.710 GHz)
40 MHz
VHT40 MCS5-MCS7
12 dBm
102 (5.510 GHz), 110 (5.550 GHz), OFDM
134 (5.670 GHz), 142 (5.710 GHz)
40 MHz
VHT40 MCS8-MCS9
10 dBm
106 (5.530 GHz)
OFDM
80 MHz
VHT80 MCS0-MCS9
8 dBm
138 (5.690 GHz)
OFDM
80 MHz
VHT80 MCS0-MCS2
16 dBm
138 (5.690 GHz)
OFDM
80 MHz
VHT80 MCS3-MCS4
13 dBm
138 (5.690 GHz)
OFDM
80 MHz
VHT80 MCS5-MCS7
10 dBm
138 (5.690 GHz)
OFDM
80 MHz
VHT80 MCS8-MCS9
8 dBm
142 (5.710 GHz)
Table 28: WLAN power table for operation in the 5 GHz U-NII-2e band
Channel
Modulation
Channel bandwidth
Data rates
Maximum power setting
149, 165
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
14 dBm
153, 157, 161
OFDM
20 MHz
6, 9, 12, 18, 24, 36 Mbps
16 dBm
149-165
OFDM
20 MHz
48, 54 Mbps
13 dBm
149, 165
OFDM
20 MHz
HT20 MCS0-MCS4
13 dBm
153, 157, 161
OFDM
20 MHz
HT20 MCS0-MCS4
16 dBm
149-165
OFDM
20 MHz
HT20 MCS5-MCS7
13 dBm
149
OFDM
20 MHz
VHT20 MCS0-MCS4
13 dBm
153, 157, 161, 165
OFDM
20 MHz
VHT20 MCS0-MCS4
16 dBm
149-165
OFDM
20 MHz
VHT20 MCS5-MCS8
13 dBm
151 (5.755 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
12 dBm
159 (5.795 GHz)
OFDM
40 MHz
HT40 MCS0-MCS4
16 dBm
151 (5.755 GHz), 159 (5.795 GHz) OFDM
40 MHz
HT40 MCS5-MCS7
12 dBm
151 (5.755 GHz), 159 (5.795 GHz) OFDM
40 MHz
VHT40 MCS0-MCS9
12 dBm
155 (5.775 GHz)
80 MHz
VHT80 MCS0-MCS9
8 dBm
OFDM
Table 29: WLAN power table for operation in the 5 GHz U-NII-3 band
UBX-16015271 - R03
Product Information
Electrical specification
Page 27 of 46
EMMY-W1 series - User Manual
4.7.2 Bluetooth
Parameter
Specifications
RF Frequency Range
2.400 – 2.4835 GHz
Supported Modes
Bluetooth v4.2 (including Bluetooth Low Energy and Classic Bluetooth with BR and EDR)
Number of channels
79
Modulation
1 Mbps: GFSK (BR)
2 Mbps: π/4 DQPSK (EDR)
3 Mbps: 8DQPSK (EDR)
Transmit Power
Class 2, Class 1, BR: 10 dBm ± 2 dB, EDR: 8 dBm ± 2 dB14
Receiver Sensitivity
-85 dBm
Table 30: Bluetooth radio specifications
4.7.3 LTE co-existence
Specific influence of BAW filters on the following RF parameters:




Wi-Fi output power
Wi-Fi sensitivity
Bluetooth output power
Bluetooth sensitivity
Characterization of LTE co-existence:



Maximum tolerated input power from LTE interferer
Rejection in LTE bands
Wi-Fi and Bluetooth desensitization in presence of LTE transmission in adjacent bands for given antenna
isolation
BAW decrease influence to LTE as well

The BAW-Filter is included only in the EMMY-W161 module variant.
4.7.4 Near field communication
4.7.4.1
Parameter
Card emulator specifications
Condition
Minimum
Type
Maximum
Units
Input carrier detection level, full-power mode, peak
sinus differential voltage on NFC_ANT_P/N pin
Input ASK modulation index15
300
mVpeak
100
Input data rate (coding depending on standard:
Manchester, Modified, Miller, or NRZ
106
848
Kbps
AC characteristics
VsensPICC
MODPICC
DRPICC
Table 31: NFC card emulator
For typical recommended operating conditions unless otherwise specified.
4.7.4.2
Reader/Writer specifications
Parameter
Condition
Minimum
Type
Maximum
Units
Power amplifier output common mode level
VDDTX/2
DC characteristics
VCMTX_PA
AC characteristics
14
15
For regulatory reasons in Europe only class 2 operations are permitted.
As defined in ISO/IEC 14443-2, for example, [a-b]/[a+b] where a and b are the peak and minimum signal amplitude respectively.
UBX-16015271 - R03
Product Information
Electrical specification
Page 28 of 46
EMMY-W1 series - User Manual
Parameter
Condition
Minimum
Type
Maximum
Units
FTXCARR
Output carrier frequency
13.553
13.56
13.567
MHz
ROUT_ANT
Power amplifier output impedance
50
Ω
MODPCD
Output ASK modulation index15
100
Table 32: NFC Reader/Writer specifications
For typical recommended operating conditions unless otherwise specified.
UBX-16015271 - R03
Product Information
Electrical specification
Page 29 of 46
EMMY-W1 series - User Manual
5 Host drivers and firmware
5.1 General principle
The EMMY-W1 series module does not contain any persistent software. A firmware binary will be downloaded
by the host operating system driver on system start-up.
5.2 Supported operating systems
5.2.1 Linux
Linux device drivers are available from u-blox. Once you sign the Limited Use License Agreement (LULA) with
u-blox, a driver package will be available. This package includes:
•
Dedicated Kernel driver, to bind the Wi-Fi, Bluetooth and NFC block to the kernel. The sources of those
drivers will be provided.
•
•
A dedicated firmware image, which will be uploaded during initialization.
Various configuration tools
•
Laboratory and manufacturing tools
For a detailed description of the driver packages, refer to EMMY-W1 series System Integration Manual [3].
UBX-16015271 - R03
Product Information
Host drivers and firmware
Page 30 of 46
EMMY-W1 series - User Manual
6 Mechanical specifications
Figure 12: Physical dimensions
UBX-16015271 - R03
Product Information
Mechanical specifications
Page 31 of 46
EMMY-W1 series - User Manual
7 Qualification and approvals
7.1 Approvals16
Products marked with this lead-free symbol on the product label comply with the
"Directive 2002/95/EC of the European Parliament and the Council on the Restriction of
Use of certain Hazardous Substances in Electrical and Electronic Equipment" (RoHS).
EMMY-W1 series Wi-Fi modules are RoHS compliant.
7.1.1 European Union regulatory compliance
The EMMY-W1 series module complies with the regulatory standards
Effective use of spectrum:
EN 300 328 V 1.8.1
EN 301 893 V 1.7.1
EMC:
EN 301 489-1/-17
Health and safety:
EN 60950-1:2006 + A11:2009
EN 62311 (WLAN)
EN 62479 (BT)
We declare that the human exposure of these modules is below the SAR limits specified in the EU
recommendations 1999/519/EC.
7.1.1.1 Equipment classes
A multi-radio module is classified as class-1 or class-2 radio equipment depending on the frequency band in
which it can operate. This equipment class is inherited by the end-product that integrates the module, thus it
must be marked accordingly.
Class-1 radio equipment can be placed on the market and put into service without restrictions.
(Article 1 of Commission Decision 2000/299/EC of April 6 2000)
This multi-radio module is defined as class-1 radio equipment when it is restricted to operate in the
following frequency bands:

Bluetooth , ISM band 2400 – 2483.5 MHz

WLAN, ISM band 2400 – 2483.5 MHz
 WLAN, U-NII band-2e 5470 – 5725 MHz
Class-2 radio equipment includes restrictions applied by Member States as indicated in Article 1(2) of the
Commission Decision. This class uses the “Alert Sign” as an equipment class identifier.
Figure 13: Alert sign to identify equipment Class-2
16
These approvals are pending.
UBX-16015271 - R03
Product Information
Qualification and approvals
Page 32 of 46
EMMY-W1 series - User Manual
If an end product allows the multiradio module to operate in the 5150-5350 MHz band (WLAN channel: 36-64),
it is defined as class-2 radio equipment and must be marked accordingly. Class-2 radio equipment must have the
"alert" sign affixed on the equipment, packaging and printed in the user manual.
The EMMY-W1 multiradio module uses harmonized frequency bands thus it is comprised by subclass H01 of
class 2 equipment, for which notification in accordance with article 6(4) of the R&TTE directive is not necessary.
A definition of subclasses of Class 2 equipment can be found in the following link:
http://ec.europa.eu/enterprise/sectors/rtte/files/rtte-subclass2_en.pdf
The table below shows the restrictions when operating WLAN at different bands within the European countries
Band
Channel number
Channel
frequency
[MHz]
Indoor use
allowed
Outdoor use
allowed
Radio
Equipment
Class
ISM
1 – 11
2412 – 2462
Yes
Yes
U-NII 1
36 – 48
5180 – 5240
Yes
No
U-NII 2
52 – 64
5260 – 5320
Yes
No
U-NII 2e
100 – 140
5500 – 5700
Yes
Yes
Table 33: Operating restrictions and radio equipment classification of EMMY-W1 series
Guidance on how the end product is marked in accordance with the R&TTE directive can be
found in the following links:
http://ec.europa.eu/enterprise/sectors/rtte/documents/index_en.htm - h2-5
http://ec.europa.eu/enterprise/sectors/rtte/documents/guidance/index_en.htm
A direct link to the quick guide to the marking requirements can be found here:
http://ec.europa.eu/enterprise/sectors/rtte/files/guidance/guidance_en.pdf
IMPORTANT: The ”CE” marking must be affixed to a visible location on the OEM product in
which this module is installed and has to be labeled in accordance to R&TTE Directive 1999/5/EC.
7.1.2 FCC compliance
The EMMY-W1 series module complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation
Non authorized modification could void authority to use this equipment. The internal / external antenna(s) used
for this module must provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
In accordance with 47 CFR § 15.19, the end product into which this module is integrated shall bear the
following statement in a conspicuous location on the device:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation
UBX-16015271 - R03
Product Information
Qualification and approvals
Page 33 of 46
EMMY-W1 series - User Manual
When the end-product is so small or for such use that it is not practical to place the above statement on it, the
information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or
on the container in which the device is marketed. However, the FCC ID label must be displayed on the device.
If the end-product will be installed in locations where the end-user is not able to see the FCC ID and/or this
statement, the FCC ID and the statement shall also be included in the end-product manual.
The outside of final products containing the EMMY-W1 module must display in a user accessible area a
label referring to the enclosed module. This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: (XYZ)(UPN)” or “Contains FCC ID: (XYZ)(UPN)”, where (XYZ)
represents the FCC “Grantee Code” and (UPN) is the Unique Product Number decided by the grant
17
owner .
7.1.3 IC compliance
The EMMY-W1 series module complies with Industry Canada license-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Any notification to the end user of installation or removal instructions about the integrated radio module
is NOT allowed. Unauthorized modification could void authority to use this equipment.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator and your
body.
This radio transmitter IC: 8595A-EMMYW161, IC: 8595A-EMMYW163 and IC: 8595A-EMMYW165 has been
approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for
that type, are strictly prohibited for use with this device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as
primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars
could cause interference and/or damage to LE-LAN devices.
The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host
device; otherwise, the host device must be labeled to display the Industry Canada certification number for the
module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording
expressing the same meaning, as follows: “Contains transmitter module IC: (CN)-(UPN)”, where (CN) is the
Company Number registered at Industry Canada and (UPN) is the Unique Product Number decided by the grant
owner.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet équipement est conforme aux limites d'exposition de rayonnement d'IC RSS-102 déterminées pour un
environnement non contrôlé. Cet équipement devrait être installé et actionné avec la distance minimum 20 cm
entre le radiateur et votre corps.
Cet émetteur radio, IC: 8595A-EMMYW161, IC: 8595A-EMMYW163 et IC: 8595A-EMMYW165 été approuvé
par Industry Canada pour fonctionner avec les types d’antenne énumérés ci-dessous avec le gain maximum
17
The FCC and IC IDs for the EMMY-W1 series module variants are shown in Table 37. Select the applicable ID.
UBX-16015271 - R03
Product Information
Qualification and approvals
Page 34 of 46
EMMY-W1 series - User Manual
autorisé et l’impédance nécessaire pour chaque type d’antenne indiqué. Les types d’antenne ne figurant pas
dans cette liste et ayant un gain supérieur au gain maximum indiqué pour ce type-là sont strictement interdits
d’utilisation avec cet appareil.
Le dispositif de fonctionnement dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur
pour réduire le risque d'interférences nuisibles à la co-canal systèmes mobiles par satellite
Opération dans la bande 5600-5650 MHz n'est pas autorisée au Canada. Haute puissance radars sont
désignés comme utilisateurs principaux (c.-àutilisateurs prioritaires) des bandes 5250-5350 MHz et 56505850 MHz et que ces radars pourraient causer des interférences et / ou des dommages à dispositifs LANEL.
L’étiquette d’homologation d’Industrie Canada d’un module donné doit être posée sur l’appareil hôte à un
endroit bien en vue en tout temps. En l’absence d’étiquette, l’appareil hôte doit porter une étiquette sur laquelle
figure le numéro d’homologation du module d’Industrie Canada, précédé des mots « Contient un module
d’émission », ou du mot « Contient », ou d’une formulation similaire allant dans le même sens et qui va comme
suit : « Contient le module d’émission IC: (CN)-(UPN) », où (CN) représente le numéro de compagnie, attribué
par Industrie Canada et (UPN) représente le numéro de produit unique attribué par le requérant.
The approval of the variant EMMY-W165 with the IC: 8595A-EMMYW165 is still in progress and
expected to be finished soon.
The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from
all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. See
Table 34 for list of approved antennas.
The approval type for all the EMMY-W1 series variants is a limited modular approval. Due to Industry
Canada Modular Approval Requirements (Source: RSP-100 Issue 10), any application which includes the
module must be approved by the module manufacturer (u-blox). The application manufacturer must
provide design data for the review procedure.
7.2 Approved antennas
For Bluetooth and Wi-Fi operation in the 2.4 GHz band and Wi-Fi operation in the 5 GHz band, the module has
been tested and approved for use with the antenna listed in Table 34.
Manufacturer
Part Number
Antenna type
Peak gain [dBi]
2.4 GHz band
5 GHz band
Antenova
A10194
SMD chip antenna 10x10x0.9 [mm] [4]
1.8
4.1
Linx
ANT-DB1-RAF-RPS
Dual-band dipole antenna [5]
2.5
4.6
Taoglas
GW.40.2153
Dual-band dipole antenna [6]
3.74
2.5
Taoglas
GW.59.3153
Dual-band dipole antenna [7]
2.37
2.93
Walsin
RFDPA870900SBLB8G1
Dual-band dipole antenna [8]
Linx
ANT-2.4-CW-RCT-RP
Single-band dipole antenna [9]
2.2
N/A
Delock
88395
Dual-band dipole antenna [10]
1.5
2.1
Table 34: List of approved dual-band antennas
The module can be integrated with other antennas which the OEM installer must authorize with respective
regulatory agencies and after approval of the module manufacturer.
UBX-16015271 - R03
Product Information
Qualification and approvals
Page 35 of 46
EMMY-W1 series - User Manual
7.2.1 Bluetooth antenna
The following antennas are designated for Bluetooth transmission on EMMY-W163:
Manufacturer
Part Number
Antenna type
Peak gain [dBi]
2.4 GHz band
Johanson
Technology
2450AT45A100
SMD chip antenna 10x10x0.9 [mm] [11]
2.2
Taoglas
GW.26.0151
Single-band monopole antenna [12]
0.0
Linx
ANT-2.4-CW-RH
Single-band monopole antenna [13]
-0.9
Table 35: List of approved single-band antennas
7.2.2 NFC antenna
The following antennas are designated to be used for Near Field Communication (NFC) on EMMY-W161,
EMMY-W163 and EMMY-W165:
Manufacturer
Part Number
Antenna type
u-blox
EMMY_NFC_ANT
External PCB antenna with connector
Table 36: List of approved NFC antenna
7.3 FCC and IC IDs (planned)
Product name
FCC ID
IC ID
EMMY-W161
XPYEMMYW161
8595A-EMMYW161
EMMY-W161-A
XPYEMMYW161
8595A-EMMYW161
EMMY-W163
XPYEMMYW163
8595A-EMMYW163
EMMY-W163-A
XPYEMMYW163
8595A-EMMYW163
EMMY-W165
XPYEMMYW165
8595A-EMMYW165
EMMY-W165-A
XPYEMMYW165
8595A-EMMYW165
Table 37: FCC and IC IDs for different models of EMMY-W1 series
7.4 Certification in other countries
Regulatory approvals for using the EMMY-W1 series module in Japan, South Korea, China, Taiwan and Australia
are pending.
UBX-16015271 - R03
Product Information
Qualification and approvals
Page 36 of 46
EMMY-W1 series - User Manual
8 Product handling
8.1 Packaging
The EMMY-W1 series modules are delivered as hermetically sealed tape and reels, to enable efficient production,
production lot set-up and tear-down. For more information about packaging, see the u-blox Package
Information Guide [1].
8.1.1 Reels
The EMMY-W1 series modules are deliverable in quantities of 500 pieces on a reel. The EMMY-W1 series
modules are shipped on reel Type A as described in the u-blox Package Information Guide [1].
8.1.2 Tapes
The dimensions of the tapes are specified in Figure 14.
Figure 14: EMMY-W1 Tape dimensions
8.2 Shipment, storage and handling
For more information regarding shipment, storage and handling see the u-blox Package Information Guide [1].
8.2.1 Moisture sensitivity levels
The EMMY-W1 series modules are rated at moisture sensitivity level 3. See moisture sensitive warning label on
each shipping bag for detailed information. After opening the dry pack, modules must be mounted within 168
hours in factory conditions of maximum 30°C/60%RH or must be stored at less than 10%RH. Modules require
baking if the humidity indicator card shows more than 10% when read at 23±5°C or if the conditions
mentioned above are not met. Please refer to J-STD-033B standard for bake procedure. }
UBX-16015271 - R03
Product Information
Product handling
Page 37 of 46
EMMY-W1 series - User Manual
8.2.2 Mounting process and soldering recommendations
The EMMY-W1 series module is a surface mount module supplied on a 4-layer FR4-type PCB with gold plated
connection pins and produced in a lead-free process with a lead-free soldering paste. The wrap page of the PCB
is max. 0,75% according to IPC-A-610E. The thickness of solder resist on the host PCB top side and the
EMMY-W1 bottom side must be considered for the soldering process.
This module is compatible with industrial reflow profile for RoHS/Pb-free solders, Sn96.5/Ag3.0/Cu0.5 solder is a
right choice. Use of "No Clean" soldering paste is strongly recommended, cleaning the populated modules is
strongly discouraged - residuals under the module cannot be easily removed with any cleaning process. Cleaning
with water can lead to capillary effects where water is absorbed into the gap between the host board and
module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between
neighboring pins.
Only a single reflow soldering process is permitted for host boards with the EMMY-W1 series modules.
The reflow profile used is dependent on the thermal mass of the entire populated PCB, heat transfer efficiency
of the oven and particular type of solder paste used. Since the profile used is process and layout dependent, the
optimum profile should be studied case by case. Recommendations below should be taken as a starting point
guide. In case of basic information necessity, please refer to J-STD-020C standard. }
Profile feature
Sn-Pb eutectic
(Sn63/Pb37)
RoHS/Pb-free
(Sn96.5/Ag3.0/Cu0.5)
Ramp up rate (TSMAX to TP)
3 °C/sec max
3 °C/sec max
Minimum soak temperature (TSMIN)
100 °C
150 °C
Maximum soak temperature (TSMAX)
150 °C
200 °C
Soak time (ts)
60 - 120 sec
60 - 180 sec
Liquidus temperature (TL)
183 °C
217 °C
Time above TL (tL)
60 - 150 sec
60 - 150 sec
Peak temperature (TP)
215 – 225 °C
235 – 245 °C
Time within +0 / -5°C of actual TP (tp)
10 - 30 sec
20 - 40 sec
Ramp down rate
6 °C/sec max
6 °C/sec max
Time from 25°C to TP
6 min max
8 min max
Table 38: Recommended reflow profile
The lowest value of TP and slower ramp down rate (2 – 3 °C/sec) is preferred.
Figure 15: Reflow profile
UBX-16015271 - R03
Product Information
Product handling
Page 38 of 46
EMMY-W1 series - User Manual
8.2.3 ESD handling precautions
EMMY-W1 series modules are Electrostatic Sensitive Devices (ESD). Observe precautions for
handling! Failure to observe these precautions can result in severe damage to the Wi-Fi receiver!
Wi-Fi transceivers are Electrostatic Sensitive Devices (ESD) and require special precautions when handling.
Particular care must be exercised when handling patch antennas, due to the risk of electrostatic charges. In
addition to standard ESD safety practices, the following measures should be taken into account whenever
handling the receiver:

Unless there is a galvanic coupling between the
local GND (i.e. the work table) and the PCB GND,
then the first point of contact when handling the
PCB must always be between the local GND and
PCB GND.

Before mounting an antenna patch, connect
ground of the device

When handling the RF pin, do not come into
contact with any charged capacitors and be
careful when contacting materials that can
develop charges (e.g. patch antenna ~10 pF, coax
cable ~50-80 pF/m, soldering iron, …)

To prevent electrostatic discharge through the RF
input, do not touch any exposed antenna area. If
there is any risk that such exposed antenna area is
touched in non ESD protected work area,
implement proper ESD protection measures in the
design.

When soldering RF connectors and patch
antennas to the receiver’s RF pin, make sure to
use an ESD safe soldering iron (tip).
UBX-16015271 - R03
Product Information
Product handling
Page 39 of 46
EMMY-W1 series - User Manual
9 Labeling and ordering information
9.1 Product labeling
The labels of EMMY-W1 series include important product information as described in this section. The data
matrix code for automotive and professional grade variants of EMMY-W1 series includes a serial number.
Figure 16 illustrates the sample label of the automotive grade (professional grade is similar and differs with
respect to product version (1) as mentioned in Table 39) of the EMMY-W1 series and includes: the u-blox logo,
product name (model), type number, FCC and IC certification number and date of unit production encoded
YY/WW (year/week).
Figure 16: EMMY-W1 series – Professional grade sample label
A detailed description of the label components are listed in Table 39. The first three digits of the serial number
represent the Bluetooth MAC address.
Reference
Description
Text “MODEL:” followed by product type number, omitting the second dash and smaller font used for the product
version identifier (“xxB-yy” for professional and “xxA-yy” for automotive grade).
Date of production encoded YY/WW (year/week)
FCC/IC ID which the module has been listed with
Data Matrix with unique serial number of 15 alphanumeric symbols.
The 3 first symbols represent the unique module type no:
631: EMMY-W161-00A-00,
632: EMMY-W163-00A-00,
700: EMMY-W163-00B-00,
701: EMMY-W161-00B-00,
756: EMMY-W165-00A-00,
???: EMMY-W165-00B-00,
, the next 8 symbols represent the unique hexadecimal Bluetooth MAC address (see section 1.7 for more information
about MAC addresses) of the module AABBCCDDEE, and the last 4 symbols represent the hardware and firmware
version encoded HHFF.
u-blox logo, the red dot in the logo is also marking pin no 1
Table 39 EMMY-W1 series label description
UBX-16015271 - R03
Product Information
Labeling and ordering information
Page 40 of 46
EMMY-W1 series - User Manual
9.2 Explanation of codes
Two different product code formats are used. The Product Name is used in documentation such as this data
sheet and identifies all u-blox products, independent of packaging and quality grade. The Ordering Code
includes options and quality, while the Type Number includes the hardware and firmware versions. Table 40
below details these three different formats:
Format
Structure
Product Name
PPPP-TGVV
Ordering Code
PPPP-TGVV-TTQ
Type Number
PPPP-TGVV-TTQ-XX
Table 40: Product code formats
Table 41 explains the parts of the product code.
Code
Meaning
Example
PPPP
Form factor
EMMY
TG
Platform
T – Dominant technology, For example, W: Wi-Fi, B: Bluetooth
G - Generation
W1
VV
Variant based on the same platform; range [00…99]
61
TT
Major Product Version
00
Quality grade
A: Automotive
B: Professional
C: Standard
XX
Minor product version (not relevant for certification)
00
Table 41: Part identification code
9.3 Ordering codes
Ordering Code
Product name
Product
EMMY-W161-00B
EMMY-W161
EMMY-W161 professional grade module
EMMY-W161-00A
EMMY-W161-A
EMMY-W161 automotive grade module
EMMY-W163-00B
EMMY-W163
EMMY-W163 professional grade module
EMMY-W163-00A
EMMY-W163-A
EMMY-W163 automotive grade module
EMMY-W165-00B
EMMY-W165
EMMY-W165 professional grade module
EMMY-W165-00A
EMMY-W165-A
EMMY-W165 automotive grade module
EVK-EMMY-W161-A
EVK-EMMY-W161
Evaluation kit for EMMY-W161 and EMMY-W161-A
EVK-EMMY-W163-A
EVK-EMMY-W163
Evaluation kit for EMMY-W163 and EMMY-W163-A
Table 42: Product ordering codes
Product changes affecting form, fit or function are documented by u-blox. For a list of Product Change
Notifications (PCNs) see our website.
UBX-16015271 - R03
Product Information
Labeling and ordering information
Page 41 of 46
EMMY-W1 series - User Manual
Appendix
A Glossary
Name
Definition
ACL
Access control list
AES
Advanced Encryption Standard
BPF
Band-Pass Filter
BT
Bluetooth
BAW
Bulk Acoustic Wave
CPU
Central Processing Unit
DTIM
Delivery traffic indication message
DC
Direct Current
DDR
Double Data Rate
ESD
Electrostatic Sensitive Devices
EMV
Europay, MasterCard and Visa
FCC
Federal Communications Commission
FIFO
First In, First Out
GI
Guard interval
GND
Ground
GPIO
General-purpose input/output
HD
High Definition
HCI
Host Controller Interface
IC
Industry Canada
IMDS
International Material Data System
IMEI
International Mobile Station Equipment Identity
LED
Light-emitting diode
LTE
Long Term Evolution
LE
Low Energy
MAC
Medium Access Control
MWS
Mobile Wireless Standards
MCS
Modulation Coding Scheme
MSL
Moisture sensitivity level
NFC
Near-Field Communication
NFCIP
NFC Interface and Protocol
OEM
Original equipment manufacturer
P2P
Peer-to-peer
PCB
Printed Circuit Board
PCN
Product Change Notification
PCM
Pulse-code modulation
R&TTE
Radio and telecommunications terminal equipment
RF
Radio Frequency
RSS
Radio Standards Specification
RH
Relative humidity
RoHS
Restriction of Hazardous Substances
SDIO
Secure Digital Input Output
UBX-16015271 - R03
Product Information
Appendix
Page 42 of 46
EMMY-W1 series - User Manual
Name
Definition
SDR
Secure Digital Rate
SMD
Surface-mount Device
SCO
Synchronous Connection-Oriented
UART
Universal Asynchronous Receiver/Transmitter
Table 43: Explanation of abbreviations and terms used
UBX-16015271 - R03
Product Information
Appendix
Page 43 of 46
EMMY-W1 series - User Manual
Related documents
[1]
u-blox Package Information Guide, document number UBX-14001652
[2]
Driver Software Application Note for ELLA-W1 series and EMMY-W1 series, document number
UBX-15012542
[3]
EMMY-W1 series System Integration Manual, document number UBX-15024929
[4]
Mixtus A10194 Product Specification, Antenova-M2M, http://www.antenovam2m.com/documents/download/40c67cf2e7a4c7b8cd0f7faed7f6d2ca4fe1886d597d5, October 2015
[5]
ANT-DB1-RAF-xxx Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-db1raf-xxx.pdf, October 2015
Specification. Part No.: GW.40.2153, taoglas, https://fccid.io/pdf.php?id=2415249, December 2015
[6]
[7]
Specification. Part No.: GW.59.3153, taoglas,
http://www.taoglas.com/images/product_images/original_images/GW.59.3153- 2.4GHz-5.8GHz Band
Mount Dipole Antenna 080910.pdf, October 2015
[8]
2015 RF Devices and High Frequency Inductors Product catalog,
http://www.passivecomponent.com/document/HF_Devices/2013RF_Catalogue.pdf, December 2015
ANT-2.4-CW-RCT-xx Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant2.4-cw-rct-xx.pdf, October 2015
[9]
[10]
Delock WLAN 802.11 ac/a/b/g/n Antenna RP-SMA 2 dBi Omnidirectional Joint, 2015-11-26
http://www.delock.com/produkt/88395/pdf.html?sprache=en, November 2015
[11]
2.45 GHz High Gain SMD Chip Antenna P/N 2450AT45A100, Johanson Technology,
http://www.johansontechnology.com/datasheets/antennas/2450AT45A100.pdf, October 2015
2.4 GHz Miniature Screw mount Monopole Antenna, taoglas,
http://www.taoglas.com/images/product_images/original_images/GW.26.0112 2.4GHz Band
Monopole SMA%28M%29RA.pdf, December 2015
ANT-2.4-CW-RH Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-2.4-cwrh-xxx.pdf, December 2015
[12]
[13]
For regular updates to u-blox documentation and to receive product change notifications, register on our
homepage (http://www.u-blox.ch/).
UBX-16015271 - R03
Product Information
Related documents
Page 44 of 46
EMMY-W1 series - User Manual
Revision history
Revision
Date
Name
Status / Comments
R01
23-June-2016
Daniel Dietterle
Draft
R02
01-July-2016
Daniel Dietterle
Document release after review
R03
05-July-2016
Daniel Dietterle
Corrected maximum output power for EMMY-W163 in Table 26 and Table 27
UBX-16015271 - R03
Product Information
Revision history
Page 45 of 46
EMMY-W1 series - User Manual
Contact
For complete contact information visit us at www.u-blox.com
u-blox Offices
North, Central and South America
u-blox America, Inc.
Phone:
+1 703 483 3180
E-mail:
info_us@u-blox.com
Regional Office West Coast:
Phone:
+1 408 573 3640
E-mail:
info_us@u-blox.com
Headquarters
Europe, Middle East, Africa
u-blox AG
Phone:
+41 44 722 74 44
E-mail:
info@u-blox.com
Support: support@u-blox.com
Technical Support:
Phone:
E-mail:
+1 703 483 3185
support@u-blox.com
Asia, Australia, Pacific
u-blox Singapore Pte. Ltd.
Phone:
+65 6734 3811
E-mail:
info_ap@u-blox.com
Support: support_ap@u-blox.com
Regional Office Australia:
Phone:
+61 2 8448 2016
E-mail:
info_anz@u-blox.com
Support: support_ap@u-blox.com
Regional Office China (Beijing):
Phone:
E-mail:
Support:
+86 10 68 133 545
info_cn@u-blox.com
support_cn@u-blox.com
Regional Office China (Shenzhen):
Phone:
+86 755 8627 1083
E-mail:
info_cn@u-blox.com
Support: support_cn@u-blox.com
Regional Office India:
Phone:
+91 959 1302 450
E-mail:
info_in@u-blox.com
Support: support_in@u-blox.com
Regional Office Japan:
Phone:
+81 3 5775 3850
E-mail:
info_jp@u-blox.com
Support: support_jp@u-blox.com
Regional Office Korea:
Phone:
E-mail:
Support:
+82 2 542 0861
info_kr@u-blox.com
support_kr@u-blox.com
Regional Office Taiwan:
Phone:
+886 2 2657 1090
E-mail:
info_tw@u-blox.com
Support: support_tw@u-blox.com
UBX-16015271 - R03
Product Information
Contact
Page 46 of 46

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 46
Language                        : de-DE
Tagged PDF                      : Yes
Title                           : NEO-7
Author                          : Error! No text of specified style in document.
Subject                         : Data Sheet
Creator                         : Microsoft® Word 2013
Create Date                     : 2016:07:18 12:14:12+02:00
Modify Date                     : 2016:07:18 12:14:12+02:00
Producer                        : Microsoft® Word 2013

EXIF Metadata provided by EXIF.tools

u blox EMMYW165 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 User Manual NEO 7

u-blox AG WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 NEO 7

Contents

EMMY-W1_User_Manual

FCC ID Filing: XPYEMMYW165

Navigation menu

Namespaces

Views

Navigation