APRO MEDIA INV-26W LCD TV User Manual
APRO MEDIA CO., LTD LCD TV Users Manual
User Manual
ENGLISH Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Safety Instructions ◎ Reorient or relocate the receiving antenna. ◎ Increase the separation between the equipment and receiver. ◎ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ◎ Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC rules. Notes & Descriptions To reduce the risk of fire, electrical shock and other injuries, keep these safety precautions in mind when installing, using and maintaining your TV. Warning : If you manipulate against the notice, it may cause serious injury or death to user. Caution : If you manipulate against the notice, it may cause slight injury to user or appliance. EN 2 26” / 32” WIDE TFT-LCD TV ENGLISH Warning Disconnect the power cable and signal cable connected to the product in case of thunder or lightning. Warning When moving it, do not apply any forces on the set. Do not attempt to touch its power cord with wet hands. Do not attempt to disassemble, repair or change the product. If any electric pin is wet or dusty, remove the moisture or dust first Whenever you need to repair, adjust or check it, refer servicing to before use. qualified service personnel. It is recommended to pull out the power cord unless you use it for a Do not directly spray water or rub it with inflammable substances long time. (thinner or benzene) when cleaning it. Damaged power cord, plug or unfitted outlet may be very dangerous. Do not wet or penetrate water over/into the set. Do not install the set close to any heating sources. When cleaning the LCD surface, disconnect the power and use a piece of smooth cloth against any scratches on it. Never use wet cloth. Do not place heavy articles on it or step on the product. Caution The product should be installed on a clean and dry place. Make sure to pull out the power cord when cleaning or removing the product. When you detect any smog, unusual noise or smell, just disconnect the electric power and refer servicing to qualified service personnel. Ventilation should be always open and the set should be installed in a well-ventilated and wide enough place (a minimum distance away from a wall 10cm or more). Do not place any bowl with water, beverage, can or other liquid products on it. Do not install the set in a place directly exposed to sunlight. Do not use or place any combustible sprayer or inflammable substances close to the product. Do not arrange the power cord close to any heating devices/sources. Install the outdoor antenna for the set far away from high voltage cables. EN 2 26” / 32” WIDE TFT-LCD TV ENGLISH Available Temperature & Humidity Operating Temperature 0~40˚C Storage Temperature -10~50˚C Operating Humidity 10~80% RH Storage Humidity 10~90% RH Precautions for Image Ghost Watching TV in a still image for an excessive time may seriously harm the LCD panel. Note that any troubles from the reckless use are not guaranteed and please be cautious of the use. 1. Digital broadcast is delivered in wide screen standard (16:9) DTV, so if the existing broadcasting program made in general screen size (4:3) is on the TV, both For dot defect [dead pixel] of LCD ; sides may not be completely displayed. TFT-LCD produced by using high-end semiconductor technology with precision of 99.9% above is used for this TV. However the pixels of R.G.B. & White color seem to be right sometimes or some of black pixels could be seen on the LCD. This is not from bad quality or functional problem and you can use it without any Any different brightness, in case limits to left/right sides are fixed, may leave image ghost of the limits on the LCD penal, if you watch it for a long time. problem. Precautions when used as a PC monitor ; Since the LCD TV is not designed for a PC monitor, it may not support very high resolutions that are supported in a PC. When you use it for the purpose, refer to the supportable resolution levels as follows. When used as a PC monitor : Optimal resolution is XGA (1,024 X 768) @60Hz This TV has RGB & DVI input connector and its optimal resolution (RGB / DVI) is 1,024 768 @ 60Hz. If you connect DVI connector, you can enjoy better image quality. 2. When you watch panorama broadcasting in a general display, it may show the central image with up/down parts removed. Any different brightness, in case limits to top/bottom sides are fixed, may leave image ghost of the limits on the LCD penal, if you watch it for a long time. When used as a DTV : 720p Input If you set 720p resolution for your Set-Top BOX output, you can enjoy better quality image & sound with the TV, because applied LCD panel is WXGA (1,366 768) resolution product. 3. Watching the screen in a still image for a long time may leave image ghost on the LCD panel. EN 4 26” / 32” WIDE TFT-LCD TV ENGLISH Contents CHAPTER 3. CHAPTER 1. Before Use 1-1. Accessories 10 1-2. Panels 11 1-3. Remote Control 14 1-4. MENU Configuration 16 1-5. Inserting the Batteries in the Remote Control 18 CHAPTER 4. Connection (PAL/SECAM) 3-1. Connecting Power 30 3-2. Connecting TV Antenna 30 3-3. Connecting PC 31 3-4. Connecting PC DVI 31 3-5. Connecting DVI (AV equipment) 32 3-6. Connecting DTV / DVD 33 3-7. Connecting SCART (Full) 34 3-8. Connecting SCART (Half) 35 3-9. Connecting Headphone (speaker) Output 36 3-10. Connecting VIDEO Output 37 Using TV Menus 4-1. Watching TV CHAPTER 2. Connection (NTSC) 40 4-2. Auto On/Off Timer 43 4-3. Change TV Channel Mode 45 2-1. Connecting Power 20 4-4. Channel Search 46 2-2. Connecting TV Antenna 20 4-5. Add/Remove Channel 47 2-3. Connecting PC 21 4-6. Channel Swap 48 2-4. Connecting PC DVI 21 4-7. V-chip Funetion 49 2-5. Connecting DVI (AV equipment) 22 4-8. Caption 51 2-6. Connecting DTV 23 4-9. Password 52 2-7. Connecting DVD 24 4-10. DTV Field 53 2-8. Connecting VIDEO / S-VHS Input 25 4-11. AVC Control 54 2-9. Connecting Headphone (speaker) Output 26 4-12. PC / DTV Mode 55 2-10. Connecting VIDEO Output 27 4-13. Stereo 56 3-14. Bilingual (Multi-Language Broadcasting) 56 EN 6 26” / 32” WIDE TFT-LCD TV ENGLISH Contents CHAPTER 1 Before use CHAPTER 5. Using Menus of Picture, Sound and Others CHAPTER 6. 5-1. Setting Display Mode 58 5-2. Setting Scale Mode 60 5-3. Setting Picture Mode 61 5-4. Setting Simultaneous Picture Mode 64 5-5. Setting Screen MENU by Simultaneous Picture 67 5-6. Setting Sound 70 5-7. Setting Others 72 Accessories 1-2. Panels 1-3. Remote Control 1-4. MENU Configuration 1-5. Inserting the Batteries in the Remote Control Using PC MENU 6-1. Auto Adjustment CHAPTER 7. 1-1. 76 6-2. Setting PC Scale Mode 78 6-3. Setting Phase/Frequency 79 6-4. Setting Position/Size 80 Services & Others 7-1. Troubleshooting 84 7-2. Concerning Services 86 EN 8 26” / 32” WIDE TFT-LCD TV ENGLISH 1-1. 1-2. Accessories Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer. User’s Manual Panels Front Panels AAA-type battery( 2) Power Cord Power Load MENU Channel Button Speaker Sound Cont. Remote Control Sensor MENU SET / Exit MENU AUTO button searches automatically TV channels if set as TV, and it adjusts automatically Remote Control EN 10 26” / 32” WIDE TFT-LCD TV for PC mode. 11 ENGLISH Rear Panels (NTSC) Rear Panels (PAL/SECAM) Power Input PC Input (Upgrade) Video/Audio Output PC Input (RGB) DVD Input (Pb Y Pr L R) DTV Input (Pb Y Pr L R) Video/Audio Iutput, S-VHS Input PC Sound Input/Head Phone Output PC Input (DVI) TV Antenna Input EN 12 26” / 32” WIDE TFT-LCD TV Power Input PC Input (RGB) SCART (FULL/HALF) DTV Input (Pb Y Pr L R) PC Input (DVI) PC Sound Input/Head Phone Output PC Input (Upgrade) TV Antenna Input 13 ENGLISH 1-3. Remote Control Functions by remote control buttons Button Function Button Function POWER Power On/Off MUTE Sound off Temporarily VIDEO Composite Video Input S-VHS S-Video Input DVD DVD Input (Y PbPr) TV TV Input RGB PC Input DVI DVI Input (Optional) COMP DTV Component Input DTV (TV2) PIP TV Input (Optional) / DTV Input (If DTV Tuner is built in) TV & Input Source Selection Button NORMAL Select Normal Display PIP PIP display Channel Selection Button SPLIT Split (PBP) TV SCAN 16 Channels Multi Scan Display Selection Button 0~9 Numeric Buttons Display Mode & Audio Control Button PRE Previous Channel ENT Input selected channels MENU Control Button LIGHT Control background Light PICTURE Control Picture Mode Channel & Volume Control Button SOUND Control Sound SCALE Control Picture Scale TV Functions & Teletext Menu Button FREEZE Pause ON SCREEN Display screen status PIP Function and Setting Button MENU Enter Main/Sub MENU EXIT Exit Main/Sub MENU CH UP / DOWN Move TV channels / Move MENU up and down VOL + / - Control Volume / MENU settings CAPTION Turn On/Off Caption MEM Add/Remove a TV CH TUNE Not Available SWAP Switch TV channels CATV TV Mode Zoom ON Zooming On/Off IN Zoom in OUT Zoom out AUTO TV : Channel search / PC : Auto Adjustment SURROUND Surround effect BILINGUAL Select Multilanguage broadcasting system EPG Electronic Program Guide STEREO STEREO/MONO SLEEP Sleep TImer setting (Option for DTV) WAKE UP Wake-Up Timer setting SET UP Other setting PIP SOURCE PIP input signal change PIP VIDEO Switch Main/PIP screen PIP AUDIO Switch Main/PIP sound PIP POSITION Change PIP position PIP SIZE Control PIP size PIP CH UP / DOWN Change PIP TV Channel The remote control provided is available up to 7m from the optical receive part within Left/Right 15 degrees. EN 14 26” / 32” WIDE TFT-LCD TV 15 ENGLISH 1-4. MENU Configuration Most functions of the TV set can be controlled by MENU and selection buttons on the 2. Press it again to move to sub menu of a selected main menu. 1) Press MENU button to display main menu. remote control, so learning how to operate them would be convenient for you. 2) Press it again to move to sub menu of a selected main menu. 1. Menu Configuration 3) Press Sub Menu Main Menu EXIT to return from sub menu to main menu or from main menu to menu removal. 4) To move among menus, use CH button. 5) To change a selected menu setting, use VOL button. Settings EN 16 26” / 32” WIDE TFT-LCD TV 17 ENGLISH 1-5. Inserting the Batteries in the Remote Control CHAPTER 2 1) Remove the cover of the remote control. 2) Check the polarity of batteries and insert them in right directions. 3) Replace the cover. Connection (NTSC) 4) Available batteries : 2 DC 1.5V AAA-type batteries Since incorrect insertion of batteries may cause breakage, leakage or injuries, check the polarities before the insertion. Separate and collect used batteries for the protection of environment. Do not use alkaline and manganese batteries together. 2-1. Connecting Power 2-2. Connecting TV Antenna 2-3. Connecting PC 2-4. Connecting PC DVI 2-5. Connecting DV (AV equipment) 2-6. Connecting DTV 2-7. Connecting DVD 2-8. Connecting VIDEO / S-VHS Input 2-9. Connecting Headphone (speaker) Output 2-10. Connecting VIDEO Output EN 18 26” / 32” WIDE TFT-LCD TV 19 ENGLISH 2-1. 2-3. Connecting Power Connecting PC 1. The product automatically adjusts voltage. PC In case 110V is used, connect 110V plug before use. 2. Power Cable should be firmly connected to an outlet or TV Power input in order not to be pulled out or shake. 2-2. Connecting TV Antenna 1. When round cable (75Ω coaxial cable) is used, copper part of the cable should not be 1. Connect D-Sub Cable to D-Sub port on the TV and PC. bent. 2. Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC Audio Input Port of the TV (stereo jack). TV Wall-outlet TV antenna 2-4. RF cable Connecting RF cable Connecting PC DVI copper wire Antenna converter Connecting feeder cable feeder cable PC TV Wall-outlet Cautions 1. When an outdoor antenna is used, it is recommended for a skilled technician to install it. 2. It may be helpful to better display to purchase additional installing amplifier if there is any problem with weak radio wave. 1. Connect DVI Cable (not included) to DVI port of the TV and PC. 2. Connect Audio Cable (not included) to Audio port of PC (stereo jack) and TV (stereo jack). 3. It is recommended to use D-type DVI cable. EN 20 26” / 32” WIDE TFT-LCD TV 21 ENGLISH 2-5. Connecting DVI (AV equipment) DVD 2-6. Connecting DTV Set-top Set-top Pb Pr Pb Pr L AUDIO R Audio Output / Video Output 1. Connect a DVI cable (Option) to DVI connector of TV, DVD, or Set-top Box. 2. Connect an audio cable (Option) between an audio connector of DVD player, Set-top Box and PC audio connector of TV. 3. When using DVI connector of AV equipment, you have to connect audio cable to PC 1. Connect Component Cable (not included) to DTV Connection ports of TV (Pb Y Pr) and DTV Receiver. 2. Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV Receiver. 3. Cables should be connected to ports of same colors. audio input connector of TV. Otherwise, it doesn't work! 4. You have to use only DVI cable of D-type. EN 22 26” / 32” WIDE TFT-LCD TV 23 ENGLISH 2-7. 2-8. Connecting DVD Connecting VIDEO / S-VHS Input DVD Player Pb Pr Pb Pr L Audio R Video & DVD Player Video S-VHS Output S-VHS Pb Pr Audio Output / Video Output S-VHS Video 1. Connect Component Cable (not included) to Component ports of TV and DVD player. 2. Connect Audio Cable (not included) to Audio ports (L/R) of TV and DVD player. 3. Cables should be connected to ports of same colors. 1. Connect Video/Audio Cable (not included) and S-VHS Cable to Video port of TV and camcorder, game machines, VCR, DVD player or Set-Top box. 2. Cables should be connected to ports of same colors. 3. Audio signals of S-VHS should be used with external audio signal cables. 4. S-VHS signal secures better quality than composite video signal. EN 24 26” / 32” WIDE TFT-LCD TV 25 ENGLISH 2-9. Connecting Headphone (speaker) Output 2-10. Connecting VIDEO Output Video & DVD Player Video Audio Intput/Video Input/S-VHS Intput 1. Connect Headphone (not included) to the Headphone output port of the TV. 2. Even in case of using headphone, internal speakers built in the TV still works and if you press MUTE button, the speakers stop working. 3. If possible, use the headphones of which impedance is 8Ω. Other headphones may 1. When recording TV program or using the video/audio of the TV for other AV device (VCR and etc), connect it to AUX Output terminal of the TV and Input Port of the device. 2. Cables should be connected to terminals of same colors. 3. External Output Signal outputs TV broadcasting signals of the main display. output too weakly or strongly. 4. In case of connecting to speakers, connect speakers with amps. If connected with speakers without amps, it may sound weakly. 5. To adjust the headphone volume level select SOUND in the configuration menu and move to “Headphone Volume”. EN 26 26” / 32” WIDE TFT-LCD TV 27 ENGLISH CHAPTER 3 Connection (PAL/SECAM) 3-1. Connecting Power 3-2. Connecting TV Antenna 3-3. Connecting PC 3-4. Connecting PC DVI 3-5. Connecting DV (AV equipment) 3-6. Connecting DTV / DVD 3-7. Connecting SCART (Full) 3-8. Connecting SCART (Half) 3-9. Connecting Headphone (speaker) Output 3-10. Connecting VIDEO Output EN 28 26” / 32” WIDE TFT-LCD TV 29 ENGLISH 3-1. 3-3. Connecting Power Connecting PC 1. The product automatically adjusts voltage. PC In case 110V is used, connect 110V plug before use. 2. Power Cable should be firmly connected to an outlet or TV Power input in order not to be pulled out or shake. 3-2. Connecting TV Antenna 1. When round cable (75Ω coaxial cable) is used, copper part of the cable should not be 1. Connect D-Sub Cable to D-Sub port on the TV and PC. bent. 2. Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC Audio Input Port of the TV (stereo jack). TV Wall-outlet TV antenna 3-4. RF cable Connecting RF cable Connecting PC DVI copper wire Antenna converter Connecting feeder cable feeder cable PC TV Wall-outlet Cautions 1. When an outdoor antenna is used, it is recommended for a skilled technician to install it. 2. It may be helpful to better display to purchase additional installing amplifier if there is any problem with weak radio wave. 1. Connect DVI Cable (not included) to DVI port of the TV and PC. 2. Connect Audio Cable (not included) to Audio port of PC (stereo jack) and TV (stereo jack). 3. It is recommended to use D-type DVI cable. EN 30 26” / 32” WIDE TFT-LCD TV 31 ENGLISH 3-5. Connecting DVI (AV equipment) DVD 3-6. Connecting DTV / DVD Set-top Set-top Pb Pr Pb Pr L AUDIO R Audio Output / Video Output 1. Connect a DVI cable (Option) to DVI connector of TV, DVD, or Set-top Box. 2. Connect an audio cable (Option) between an audio connector of DVD player, Set-top Box and PC audio connector of TV. 3. When using DVI connector of AV equipment, you have to connect audio cable to PC 1. Connect Component Cable (not included) to DTV / DVD Connection ports of TV (Pb Y Pr) and DTV / DVD Receiver. 2. Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV / DVD Receiver. 3. Cables should be connected to ports of same colors. audio input connector of TV. Otherwise, it doesn't work! 4. You have to use only DVI cable of D-type. EN 32 26” / 32” WIDE TFT-LCD TV 33 ENGLISH 3-7. 3-8. Connecting SCART(Full) Connecting SCART(Half) Set-top SCART DVD Video & DVD Player SCART Audio Output / Video Output 1. Connect SCART Cable (not included) to SCART port of TV and DVD player, VCR, SetTop box or camcorder. EN 34 26” / 32” WIDE TFT-LCD TV 1. Connect SCART Cable (not included) to SCART port of TV and DVD player, VCR, SetTop box or camcorder. 35 ENGLISH 3-9. Connecting Headphone (speaker) Output 3-10. Connecting VIDEO Output Video & DVD Player Pb Pr 1. Connect Headphone (not included) to the Headphone output port of the TV. 2. Even in case of using headphone, internal speakers built in the TV still works and if you press MUTE button, the speakers stop working. 3. If possible, use the headphones of which impedance is 8Ω. Other headphones may Pb Pr L AUDIO R 1. When recording TV program or using the video/audio of the TV for other AV device (VCR and etc), connect it to AUX Output terminal of the TV and Input Port of the device. 2. Cables should be connected to terminals of same colors. 3. External Output Signal outputs TV broadcasting signals of the main display. output too weakly or strongly. 4. In case of connecting to speakers, connect speakers with amps. If connected with speakers without amps, it may sound weakly. 5. To adjust the headphone volume level select SOUND in the configuration menu and move to “Headphone Volume”. EN 36 26” / 32” WIDE TFT-LCD TV 37 ENGLISH CHAPTER 4 Using TV Menus EN 38 26” / 32” WIDE TFT-LCD TV 4-1. Watching TV 4-2. Auto On/Off Timer 4-3. Change TV Channel Mode 4-4. Channel Search 4-5. Add/Remove Channel 4-6. Channel Swap 4-7. V-chip Funetion 4-8. Caption 4-9. Password 4-10. DTV Field 4-11. AVC Control 4-12. PC / DTV Mode 4-13. Stereo 4-14. Bilingual (Multi-Language Broadcasting) 39 ENGLISH 4-1. 3. Channel Selection Watching TV 1) Press CH button on the remote control to change channels. 2) Press numeric buttons to go to a channel directly. 1. Precautions in the initial installation 3) Press CH buttons ( ) on the TV set to increase or decrease TV channels. 1) Check whether TV antenna cable is properly connected. 2) After checking whether the voltage is 100V or 220V, supply the electric power and connect the adaptor to the TV. At the moment, TV is in standby. 2. Turning on TV Channel button on the remote control Channel button on the TV set 1) Turn on the Power button directly on the set or by remote control. 2) Each pressing the button turns on or off the set. 4. Volume Control 1) Increase/decrease volume by pressing VOL button on the remote control. 2) Press VOL button ( Power Button on Remote Control ) on the TV set to control the volume. Power Button on the TV Set Volume Button on the remote control EN 40 26” / 32” WIDE TFT-LCD TV Volume Button on the TV Set 41 ENGLISH 4-2. 5. Mute 1) Press MUTE Auto On/Off Timer button on the remote control to sound off temporarily and “MUTE” is displayed. 2) Press it again to turn the sound back on or press volume buttons. MUTE button on the remote control You may set the TV to turn on or off in a certain time period. 1. Setting Wake-Up Timer - Press WAKE UP button on the remote control. 6. Move to Previous Channel 1) Every time pressing the PRE button on the remote control, it moves to a previous channel. - Set the time to turn on the TV automatically by using volume button on the remote control. - Wake-up timer can be set from Off to 12 hours. Previous Channel Button - Once the setting is complete, press WAKE UP button again or EXIT button. - Also, it can be set in OSD menu if OSD button is used. 7. Checking the present broadcasting information 1) Press ON SCREEN button on the remote control to display the information on the screen. 2) Press ON SCREEN button again removes the information or leaving it clears the information in 5 seconds. Broadcasting Info Button In case of TV Signal, it displays channel info while it shows mode info in case of PC signal. EN 42 26” / 32” WIDE TFT-LCD TV 43 ENGLISH 2. Setting Sleep Timer 4-3. Change TV Channel Mode - Press SLEEP button on the remote control. Please set your broadcast type between Air and Cable. If its mode is set as Air, some Cable broadcasts are not able to watch. - Set the sleep timer by using volume button on the remote control. - Sleep Timer can be set from Off to 180 minutes. - Once the setting is complete, press SLEEP button again or EXIT button. - Press CATV button on the remote control. - Also, it can be set in OSD menu if OSD button is used. - Set the CH Mode between Air & Cable by using VOL button on the remote control. - Once the setting is complete, press CATV button or EXIT button. - Also, it can be set in OSD menu if OSD button is used. EN 44 26” / 32” WIDE TFT-LCD TV 45 ENGLISH 4-4. Channel Search 4-5. Add/Remove Channel When using the TV first after purchase, reconnecting it due to power failure or other You may add or remove a channel as your need. reasons, channels should be searched and registered again. - Move to a channel to add or remove by pressing numeric buttons or CH button. Since Channel Search function searches channels currently broadcasted, you should - Press MEM button on the remote control. execute it when most channels are broadcasted. - Press AUTO button on the remote control. - In case of adding a channel by using Volume button on the remote control, move to Add or Remove. - Once you move to START by using Volume button on the remote control, it starts channel search. - Once the setting is complete, press MEM button again or EXIT button. - Also, it can be set in OSD menu if OSD button is used. - To stop channel search, repress AUTO button on the remoter control. - If you stop it during channel search, it stores the currently searched channels only. - Also, it can be set in OSD menu if OSD button is used. EN 46 26” / 32” WIDE TFT-LCD TV 47 ENGLISH 4-6. Channel Swap 4-7. V-Chip Funetion In case of channels frequently watch, you can switch it to other channel numbers and It makes MPAA rating of TV broadcast and other media. store them. It works only with V-Chip function broadcast and media. - Move to a channel to change. It can be controlled by using the remote control only. - Press SWAP button on the remote control. - Press SETUP button on the remote control. - Move to V-Chip menu by using CH button on the remote control. - Change a channel number to switch by using Volume button on the remote control. - Once the setting is complete, press SWAP button again or EXIT button. - Also, it can be set in OSD menu if OSD button is used. - Press MENU button and enter Password. - Press ENT or MENU button on the remote control. - Set V-Chip function by using EN 48 26” / 32” WIDE TFT-LCD TV VOL button on the remote control. 49 ENGLISH - Move to TV Guideline or MPAA Rating by using CH button on the remote control. 4-8. Caption This function works only Caption broadcast or other CC marked video tape and DVD title. Set the function in the SETUP menu. Caption can be set only by using the remote control. 1. Caption On / Off - Move to the position which you want to make channel blocking and press button for setting. - Press it again for cancellation. MENU - Press CAPTION button on the remote control when it is broadcasted. - Press CAPTION button for coming out from setting. 2. Set Caption - Press SETUP button. - Move to Closed Caption menu by using CH button. - Set Caption broadcast type by using VOL button on the remote control. - Press EXIT button for coming out from setting. - Press EXIT button for coming out from setting. EN 50 26” / 32” WIDE TFT-LCD TV 51 ENGLISH 4-9. Password 4-10. DTV Field When using Contents Blocking function, you can set password and please keep the Depending on a DTV receiver, a signal is not identical with standard signal. It may cause password private. unclear display and if you change DTV Field value, it will be recovered to the normal Default password is <0000>. picture (it can be set only by the remote control). Please change default password to new one after installing TV. - Press SET UP button. - Press SET UP button on the remote control. - Move to password menu by using CH button on the remote control - Press MENU button to go into DTV Field Setting Menus. - Set Not Invert/Invert with Volume button. - Initially, ‘Not Invert’ is defaulted and you may change it to ‘Invert’ if the - Press MENU button on the remote control for entering Password setting menu. display is not normal. - When setting password first after purchase, press <0000> on the remote control and press ENT or MENU on the remote control after entering new password for changing. - Once the setting is complete, press the EXIT button. - Press new password and EN 52 26” / 32” WIDE TFT-LCD TV ENT or MENU again for confirmation it. 53 ENGLISH 4-11. AVC Control 4-12. PC / DTV Mode AVC (Automatic Volume Correction) Control : This option is properly control Use this function when you use DVI connector for DTV / PC input signal. its sound volume level if there is different volume level from same sound When you use PC / DTV signal, please set its proper mode as PC / DTV, because PC & source. DTV input signal is different. - Press SET UP button on the remote control. - Press SET UP button on the remote control. - Move to AVC Control menu by using CH button. - Move to PC / DTV Mode menu by using CH button. - Select AVC control menu by pressing MENU button. - Select PC / DTV Mode by pressing MENU button. - Change its ON/OFF setting by using VOL button. - Set its PC / DTV mode by using VOL button. - Once the setting is complete, press the EXIT button. - Once the setting is complete, press the EXIT button. NOTICE If the screen size is not properly set on the display, please check whether you changed its mode before input signal changed please check its input mode whether it is properly set as PC or DTV. EN 54 26” / 32” WIDE TFT-LCD TV 55 ENGLISH 4-13. Stereo CHAPTER 5 If you use the TV in an area with weak or bad reception, there may cause sound noise or other problem when selecting a channel. In this case, cancel the STEREO setting. It can be canceled only by the remote control. - Press STEREO button on the remote control to cancel stereo and Using Menus of Picture, Sound and Others returning to Mono. - Press STEREO button in Mono returns to Stereo. - If Stereo is off, it is always set as Mono even though a channel is 5-1. Setting Display Mode 5-2. Setting Scale Mode 5-3. Setting Picture Mode 5-4. Using Simultaneous Picture Mode 5-5. Setting Screen MENU by Simultaneous Picture 5-6. Setting Sound 5-7. Setting Others changed. 4-14. Bilingual (Multi-Language Broadcasting) In case of multi-language broadcasting, it can be converted if you wish to listen to other language except main language. Multilanguage broadcasting can be set only by the remote control. - Every time pressing BILINGUAL button on the remote control, the language display is changed in good order of main language language sub main + sub languages (dual language). (Main - Sub - Dual) EN 56 26” / 32” WIDE TFT-LCD TV 57 ENGLISH 5-1. Setting Display Mode 4) SPLIT FULL : Repressing SPLIT button in Split display, shows main screen and sub screen in split full screen. You may view other video screen while watching TV. - Press NORMAL , PIP , SPLIT or TV SCAN button. 1) NORMAL : Show a selected main screen in full size. 5) TV SCAN : Show 16 channels searched and stored in the TV set in 16 pictures in order on the screen. At the moment, TV SCAN can be operated only by the remote control. 2) PIP : Show main screen and sub screen in full size and small size together. - Also, it can be set in OSD menu if OSD button is used. - OSD Menu is different depending on Display Type [Screen Layout]. 3) SPLIT : Show main screen and sub screen by horizontally shared. You can control Main screen’s (left side screen) size and Sub screen’s size is controlled inverse ratio of main screen. EN 58 26” / 32” WIDE TFT-LCD TV 59 ENGLISH 5-2. 5-3. Setting Scale Mode Setting Picture Mode You can set the screen’s suitable image scale of TV or Video input signals and view them By setting a picture mode suitable for broadcasting/video signals, you may enjoy better accordingly. quality picture. - Press SCALE button on the remote control. - Press PICTURE button on the remote control. - Control the scale (s) in desirable size (s) by using Volume button on the remote control. - Set a picture mode by using Volume button on the remote control. 1) FULL : Show a screen in the full LCD Penal. 1) Standard : Standard picture mode. 2) 16:9 : Show a screen in 16:9 wide screen size. 2) Soft : It displays a picture softly as a whole and is better for watching a film or TV 3) 4:3 : Show a screen in 4:3 screen size for general broadcasting. series. 4) CAPTION : Show a screen suitable for Caption Broadcasting. 3) Dynamic : The mode is suitable for watching sports, which changes pictures fast. 5) SMART VIEW : Show a screen in a proportion suitable for grand image. 4) User : It is a picture mode customized by a user. In PIP or SPLIT screen, it can be set in types of AUTO, 16:9, 4:3. For more information, - Also, it can be set in OSD menu if OSD button is used. see to 4-4 Setting Simultaneous Picture Mode. - Once the setting is complete, press PICTURE button or EXIT button on the remote control. - Also, it can be set in OSD menu if OSD button is used. - OSD Menu is different depending on Display Type [Screen Layout]. EN 60 26” / 32” WIDE TFT-LCD TV 61 ENGLISH 1. Setting USER Mode 2. Setting Room Light You can set each picture mode according to your taste. If you set USER mode as your You can adjust the entire TV brightness according to lightning status. taste, it is stored as USER Mode standard. - Press LIGHT button on the remote control. - Press MENU button on the remote control and move to PICTURE of main menu by using CH button on the remote control. - Press MENU button on the remote control and move to the sub menu for changing values by using CH / VOL buttons. - Adjust values by using Volume button on the remote control. - Once the setting is complete, press LIGHT or EXIT button on the remote control. 1) Brightness : Adjust screen brightness. 2) Contrast : Adjust screen contrast. 3) Color : Adjust screen color. 4) Tint : Adjust screen tint. 5) Sharpness : Adjust screen sharpness. 6) Room Light : Adjust the brightness of TV screen according to background brightness. EN 62 26” / 32” WIDE TFT-LCD TV 63 ENGLISH 5-4. Setting Simultaneous Picture Mode 3. Changing Sub Screen Size It adjusts sub screen size. While watching TV on main screen, you can enjoy other video picture on the sub screen. Simultaneous Picture means PIP and/or SPLIT Picture display. - Press SIZE button on the remote control. - Adjust sub screen size by Volume button on the remote control. - Different menus are displayed depending on PIP Picture or SPLIT Picture. 1. Changing a channel of Simultaneous Picture - Press CH button on the remote control. - It changes a TV channel if the sub screen shows TV. - On PIP Picture, sub screen size can be adjusted from 1/16 to 1/4 of the full size. 2. Changing input signal of Sub-Screen - Press SOURCE button on the remote control. - Every time pressing SOURCE button, it changes input signal of sub screen. - Available input signals of sub screen are as follows; SUB PC PC RGB DVI PC RGB PC DVI TV MAINRGB COMP TV VIDEO S-VHS (DTV) DVD accordingly. VIDEO S-VHS COMP (DTV) DVD EN 64 26” / 32” WIDE TFT-LCD TV - On SPLIT Picture, main screen size is adjusted while sub screen size is adjusted - On SPLIT Picture, the left screen always shows main screen. 65 ENGLISH 5-5. 4. Changing Sub Screen Position Setting Screen MENU by Simultaneous Picture Adjust a sub screen’s position on PIP Picture. Depending on Layout in OSD Menu, sub menus of SCREEN are changed. - Press POSITION button on the remote control. - Move PIP picture to a desirable position by using CH / VOL button on the remote control. 1. SCREEN MENU in NORMAL Picture - It works only in NORMAL Picture. - Select SCREEN menu by pressing MENU button on the remote control (MENU MENU). - The position is set as USER setting of OSD menu. - Once the setting is complete, press POSITION or EXIT button on the remote control. 5. Switching Main/Sub Screen It switches main/sub screens. In case of switching main/sub screens, audio is changed accordingly. The left screen always shows main screen. 1) Layout : Set Picture mode [Display Mode]. 6. Switching Audio of Main/Sub Screen 2) Image Scale : Select an image scale (FULL, 16:9, 4:3, Caption, Smart View) It switches audio of main/sub screen. - Once the setting is complete, press EXIT button to exit it. In case of switching audio of main/sub screen, it switches audio only, not screens. EN 66 26” / 32” WIDE TFT-LCD TV 67 ENGLISH 2. Screen Menu on PIP Picture 3. SCREEN Menu in SPLIT Picture - It works only on PIP Picture. - It works only on SPLIT Picture. - Select SCREEN menu by pressing MENU button on the remote control. - Select SCREEN menu by pressing MENU button on the remote control. 1) Layout : Set a display layout. 1) Layout : Set a display layout 2) Image Scale : Select an image scale of main screen. 2) Split Size : Adjust a size of Split main screen. Sub screen size is adjusted by main (FULL, 16:9, 4:3, Caption, Smart View) 3) PIP Position : Adjust the position of PIP (L-Top, L-Bottom, R-Top, R-Bottom, USER) 4) PIP Position X / Y : In case of PIP Position menu is set as USER, it sets X/Y position of PIP. screen size. 3) SPLIT Scale : Adjust an image scale of SPLIT Picture. - Auto : Adjust PIP scale by automatically determining input signals. - 16:9 : It fixes PIP sub screen scale to 16:9. - 4:3 : It fixes PIP sub screen scale to 4:3. 5) PIP Size : Adjust PIP size. It can be adjusted from 1/16 to 1/4 of full screen. 6) PIP Scale : Adjust image scales of PIP. - Auto : Adjust PIP scale by automatically determining input signals. - 16:9 : It fixes PIP scale to 16:9. - 4:3 : It fixes PIP scale to 4:3. EN 68 26” / 32” WIDE TFT-LCD TV 69 ENGLISH 5-6. Setting Sound 2. USER Mode Setting USER mode can be set only in OSD menu. You can set sound suitable for TV broadcasting or Video. - Press MENU button to go into main menu. - Move to SOUND menu by using CH button. 1. Mode Setting - Press MENU button to move to the Sub Menu. - Adjust sound in a desirable frequency bandwidth by using VOL - Press SOUND button on the remote control to display SOUND mode setting. / CH button on the remote control. 3. SURROUND Setting - Set the menu settings by using Volume button on the remote control. Surround mode can be set only by the remote control. 1) Standard : Standard sound mode. - Press SURROUND button on the remote control. 2) Music : Music broadcasting mode. - Set ON/OFF by using Volume button on the remote control. 3) Movie : Cinema broadcasting mode. 4) News : News broadcasting mode. 5) User : User’s customization mode. Also, it can be set in OSD menu if OSD button is used. - Once the setting is complete, press SURROUND or EXIT button on the remote control. Balance : Control Left/Right speaker balance. Headphone Volume : Control headphone volume. EN 70 26” / 32” WIDE TFT-LCD TV 71 ENGLISH 5-7. Setting Others 2. Setting OSD Menu Language Change a language to display OSD. Press MENU button on the remote control to move to Main Menu. Move to OPTION menu by using CH button on the remote control Press MENU button to move to the Main menu. Change the settings by using VOL / CH button on the remote control. 3. Factory Reset 1. Menu Timeout Setting Reset all the OSD control settings back to the factory setting status. It can be adjusted to display OSD Menu between 5 ~ 60 seconds. EN 72 26” / 32” WIDE TFT-LCD TV 73 ENGLISH 4. Version It shows the product version. CHAPTER 6 Using PC MENU EN 74 26” / 32” WIDE TFT-LCD TV 6-1. Auto Adjustment 6-2. Setting PC Scale Mode 6-3. Setting Phase / Frequency 6-4. Setting Position / Size 75 ENGLISH 6-1. Auto Adjustment In case of using it as a PC monitor, it is automatically set. When the set is connected to a PC, the MODE should be set as PC RGB Mode. - Press AUTO button on the remote control to automatically set the product’s screen status. The Standard Signal Modes for PC Monitor Resolution (H*V) 640 480 800 600 1024 768 1280 720 1280 768 RGB DVI - Move to START by using Volume button on the remote control to start Auto Adjustment. When it is used as a PC monitor; The Standard Signal Modes for PC Monitor Optimal Resolution: 1024 x 768 @ 60Hz Max. Resolution: 1024 x 768 @ 85Hz. Resolution - It may not normally display picture in any resolution out of the optimal resolution range. - When you use it as a PC monitor, it requires to be set the Standard Signal Mode for PC Monitor before use. - Even though it is automatically adjusted, it may not normally display picture depending on signals from a PC and in this case, it is recommended to execute Auto Adjustment for several times. Also, it can be set in OSD menu if OSD button is used. (H V) Vertical Frequency Horizontal Frequency Clock Frequency Polarity (kHz) (Hz) (MHz) (Vert./Hor.) 640 480 31.469 59.94 25.175 -/- 640 480 37.861 72.809 31.5 -/- 640 480 37.5 75 31.5 -/- 720 400 31.469 70.087 28.322 -/+ 800 600 37.879 60.317 40 +/+ 800 600 48.077 72.188 50 +/+ 800 600 46.875 75 49.5 +/+ 1024 768 48.363 60.069 65 -/- 1024 768 1024 768 (Optimal) 1280 720 56.476 70.069 75 -/- 60.023 75.029 78.75 +/+ 44.955 59.94 74.086 -/+ When you use it as a PC monitor, depending on signals of a PC, it may not display picture normally even though it is set for standard mode resolution. EN 76 26” / 32” WIDE TFT-LCD TV 77 ENGLISH 6-2. Setting PC Scale Mode When being used as a PC Monitor, the scale can be adjusted. 6-3. Setting Phase / Frequency In case it is not optimally set even though automatically adjusting it, use PHASE function. PC Monitor Scale works only when PC signal is connected and input signals are selected - Press MENU button on the remote control. in RGB mode. - Move to PC menu by using CH button. - Press SCALE button on the remote control. - Move to PHASE menu by pressing MENU button. - Adjust settings by controlling Volume button. - Once the setting is complete, press EXIT button. - Select a desirable scale by using Volume button. - Once the setting is complete, press EXIT button. 1. 1:1 : Display the resolution as 1:1. 2. Fill All : Display picture in the full screen regardless of the resolution. 3. Aspect Ratio : Display the resolution in 4:3 aspect ratio. Also, it can be set in OSD menu if OSD button is used. EN 78 26” / 32” WIDE TFT-LCD TV 79 ENGLISH 6-4. Setting Position / Size (1) Setting Vertical/Horizontal Size - Press MENU button on the remote control. - Move to PC Menu by using CH button. Adjust the position and size of the PC Monitor. - Move to H / V Size Menu by using MENU button. - Adjust settings by controlling VOL button. 1. Setting Vertical/Horizontal Position - Once the setting is complete, press EXIT button. - Press MENU button on the remote control. - Move to PC Menu by using CH button. - Move to H / V Position Menu by using MENU button. - Adjust settings by controlling VOL button. - Once the setting is complete, press EXIT button. EN 80 26” / 32” WIDE TFT-LCD TV 81 ENGLISH CHAPTER 7 Service & Others EN 82 26” / 32” WIDE TFT-LCD TV 7-1. Troubleshooting 7-2. Concerning Services 83 ENGLISH 7-1. Troubleshooting 2. PC Monitor-related Troubles Before contacting service to service personnel, please check the followings first. No image on the monitor If you still have the same symptoms even after taking the following actions, contact your Check whether the D-Sub cable is firmly connected to the TV and a PC. local dealer or qualified service personnel. Check whether a graphic card is correctly inserted into the slot. Check whether the Power of a PC and the TV is on. 1. TV-related Troubles Check whether a graphic card or mode is set appropriately on a PC. Referring to the Standard Signal Mode for PC Monitor in the previous chapter, change Unclear display or noisy sound graphic mode. Check whether TV antenna is correctly connected. Check whether D-Sub cable pins are not inserted or bent. Broadcasting may not be good in an area with bad reception or far away from a station/network. No Power Check whether the power cord is normally inserted and reconnect it. No image Pull out the power cord from wall outlet and reconnect it in 10~20 minutes. Check whether you connect the power cord properly. And press the POWER button. LED Lamp turns off in red and it shows no image Black background only Check whether the graphic cable is connected to theTV and a PC. Check whether the mode is set as PC monitor or Video/S-VHS Input, not TV mode. Check whether a computer is in power-saving mode and attempt to operate keyboard and mouse. Strips and shaking display It may be interrupted by neighboring radio waves (please check any wireless phone, Unstable or unfocused image or trembling hair drier, electric drilling machine and etc) Check whether the D-Sub cable is connected to the TV and a PC. Execute fine tuning for manual adjustment. If a PC’s display mode is changed, the screen needs readjusting, so you need to use Auto Adjustment or Picture Adjustment. Can’t catch a specific channel Check whether the TV and your graphic card are compatible each other and whether it Check whether Channel Setting is normally set. is set as an appropriate refresh rate. If letters look distorted, change the refresh rate to Try to rotate an antenna’s direction. 60Hz. Picture plays without sound Abnormal image scale Try to press MUTE button. By using vertical/horizontal position in Picture Adjustment Menus, adjust the position. Volume up by using Volume button. Try to execute Auto Adjustment function. EN 84 26” / 32” WIDE TFT-LCD TV 85 ENGLISH 7-2. Concerning Services We guarantee free of charge After-sales service for a full year if any troubles are found when you are using our product. However, any natural disasters or careless use cause the trouble, it may cost even within a valid warranty period. Responsibility of Chargeable After Sales Service (Customer’s Charge) In one of the following cases, it may cost even in the valid warranty period. 1. In case of any troubles resulting from inserting of foreign substances (water, beverage, coffee and etc) 2. Dropping or applying force cause a trouble to damage on the product or induce malfunction. 3. Appearance damage or transformation by use of organic solutions such as thinner, benzene and etc. 4. When it gets troubled due to your disassemble. 5. When other parts/consumption accessories (including adaptor) that are not supplied by the company may directly cause any troubles. 6. Supplying wrong voltage may cause a trouble 7. Any personnel not from qualified service personnel repairs or modifies the product, resulting in troubles. 8. Natural disasters (lightning, fire, flood, gas, damage from sea wind, earthquake and etc) directly cause troubles 9. Violation against the directions in the manual cause any troubles 10. Customer’s mishandling cause a trouble 11. In case the date of purchase may be vague, the valid warranty period is counted after 2 months since the product is manufactured. EN 86 26” / 32” WIDE TFT-LCD TV 87
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2005:05:27 10:32:17Z Modify Date : 2005:06:03 14:50:31+09:00 Page Count : 45 Has XFA : No Creation Date : 2005:05:27 10:32:17Z Producer : Acrobat Distiller 4.0 for Macintosh Author : µðÀÚÀÎ³Ý Mod Date : 2005:06:03 14:50:31+09:00 Metadata Date : 2005:06:03 14:50:31+09:00 Creator : µðÀÚÀÎ³Ý Title : #À̳ëºä32/26¿µ2EXIF Metadata provided by EXIF.tools