CHUANGXIANG TOYS FACTORY CXMODEL023A 2.4 GHZ 4 CHANNEL RC FOR QUADCOPTER User Manual
CHUANGXIANG TOYS FACTORY 2.4 GHZ 4 CHANNEL RC FOR QUADCOPTER Users Manual
Users Manual
AGES 14+ INSTRUCTIQN 1.INTRODUCTION This quadcopter is an easy-to-fly,fu|| featured remote control model that can hover,flip.thrown and fly in all directions with different sensitivitiesplease read this manual carefully before operating this producl 2.SPARE PARTS AND DETAILED VIEW PART NAME PART NAME Protective cover Upper canopy Receiver board Underneath canopy Li-po battery Tapping screw 3. TRANSMITTER Introduction of transmitter ‘ Mobile holder Forward trimmer One key landing , Speed One key Takeoff Fllps { - Forward, backward and left/ Throttle/steenng roystrck , ‘ nght srde fly rocker Power switch backward trimmer Unlock] Return emergency slop Headless mode Right trimmer Left tnmmer Take out the cover Install 3xAM battery Retum the cover according to the correct polarities 4.LI-PO BATTERY CHARGING 4.1 equipped with a 3.7V Li-Po battery. The USB charger will light up when it’s connected to a power source The light turns all while charging the quadecpter. The red light on the USB socket will turn on when it’s full charged. You can conned the USB charger to any USB outlet Including wall and car USE adapters. Fully charging your helicopter takes about 40 mInutas. Always make sure to turn cit ma quadoopter while charging. 4.2 Safety Precautions 4 t » The battery shall not exposed to a circumstances 01 high temperature. such as open fire or electric heating device. Or it may cause fire or damage to the battery. » The battery shall be charged with the charger attached in package. - The battery shall not be dismantled. - Never charge batteries unattended. 5.READY TO FLY 5.1 Turn on your quadcopter.put it on the Horizontal position. Horizontal position TIPS: When matching signalJteep the quadcopter on horizontal position for taster matching and starting a stable flight. 5.2 Press the power switch to turn on the transmitter. 5.3 Frequency Matching Turn on both the controller and the aircraft. before matching. the indicators flash 5|°W|Y. Push the throttte up and down, after matching, the indicators keep on lighting instead of flashing. 54 press Unlock button, then push the throttle or press a key departure, aircraft will fly Into the air. 6.CONTROL METHOD Push the direction lever up or down ,the quadcopter flies forward or backward. Emergency stop: long press 1 second to stop (he aircrafl, 7.FLIPS Enter the flip mode, flashing, buzzer sound 1 second 1, press ihe flip mode key again Io exlt flip pattern. 7.1 Left side flip Push right throttle 10 Ian Aha quadeoplar can perform 360‘ in Isfl directlons. 7.2 Right side flip Push right throttle to right ,the quadooptar can perform 360° in right directions 7.3 Fowvard flip Push fight throttle to up the quadcopler can pertorm 360' forward directions. 7.4 Backward flip Push right throws to down .the quadoopter can perform 360° backward direcfions. 5m, 8.SPEED SWITCH The Nee-Drone ieaiures 3 speed modes. Lew speed is at 4036. Medium Is ai 70‘/-. and High Is at 100V» Choose «he speed based on flight experience and level at oormeri. Punch the ihrome button in to change the speed mode The remote comm! indicate! will beep ence ier low speed. iwice for medium. and three limes for high. 9.FINE-TUNING OPERATION 9.1 Sideward fly trimmer When the quadcopier keeps flying to left! right side. you can correct it by pressing the Fine-tuning bulton right / lend When the quadcepier keeps flying lorward I backward. you can correct It by presslng fine-tuning buiton right / Iefl. 9.3 Fine-tuning resetting To set the trim buttons back to deiault. push the throttle to the lower Iefl corner and the direction slick to the lower right comer at the same time and hold for three seconds. You'll hear a beep and this will reset the drone, Correctlon 10. TROUBLE SHOOTING 10.1 Transmitter and the quadcopter does not bind. Solution: Make sure the quadoopter is fully charged. Make sure to tum off the quadeopter while charging. 10.2 Quadcopter is not stable. Gyroscope is not working well. Solution: Make sure the quadoopter is fully charged. Re—bind the transmitter and the quadoopter by turning them off and on again. Make sure the quadoopter is in horizontal position on a stable flat surface. 10.3 Quadcopter does not flip. Solution Push down the left stick. 10.4 Quadcopter is shaking with noise. Solution: Check It the motors. canopy, and propellers are all properly positioned. 10.5 Quadcopter does not take off. Solutions: Check ifell the propellers are property Installed. Propellers marked as 'A" should be placed on motors marked as “A" and vice versa. Check it the canopy is loose and blocking propellers. 10.6 when the fuselage impacts may lead to increased oondmon, the body should be placed stationary, remote control rod broke ofi "A" recalibrating the gyroscopes 11. REPLACEMENT OF THE FAN BLADE Importance: leplacelhecoflespondng finblade,"yourgplaoethe wrmgfanbladeJtmzyM bemofled lWhenfiyln AtvefanbtadeA matesm hmsedirecnm. rid the tan blade 8 rotates in ant-clockwise fireman 001 Receiver 002 Main 003 Battery 004 Motor A/B board Blades “$31. 005 Campy 006 Protective 007 Transmitter cover Notice: please keep away person ,High-rise buildings,High-voltage wire and so on ,a|so avoid flying under wind rain ,thunder and bad weather .the quadcopter is made up by many Precision electronic components and mechanical parts. so prevent Moisture or water vapor into the body's internal. In order to avoid mechanical, electronic components failure caused an accident. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: ( 1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 11 Language : zh-CN Tagged PDF : Yes Author : 微软用户 Creator : Microsoft® Word 2010 Create Date : 2018:02:03 15:39:51+08:00 Modify Date : 2018:02:03 15:39:51+08:00 Producer : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools