Crestron Electronics CWD7083 Two-Way RF Transceiver Module User Manual Manual CWD7083 Doc7402A 20120514
Crestron Electronics Inc Two-Way RF Transceiver Module Manual CWD7083 Doc7402A 20120514
Manual
Crestron CWD7083 Two-Way RF Transceiver Module Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more if the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help Industry Canada (IC) Notice of Compliance Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Industrie Canada (IC) avis de conformité Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. To satisfy RF exposure requirements, this device and its antenna must operate with a separation distance of at least 20 centimeters from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. The specific patents that cover Crestron products are listed at patents.crestron.com. Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. ©2012 Crestron Electronics, Inc. Crestron CWD7083 Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: CWD7083 ..............................................1 Functions and Features .............................................................................................................. 1 Specifications............................................................................................................................. 2 Physical Description .................................................................................................................. 2 Setup .......................................................................................................................................... 4 Labeling Requirements .............................................................................................................. 4 Documentation ........................................................................................................................... 4 Operations Guide - DOC. 7402A Contents i Crestron CWD7083 Two-Way RF Transceiver Module Two-Way RF Transceiver Module: CWD7083 Functions and Features The CWD7083 (hereafter referred to as “module”) is a two-way radio frequency (RF) module that utilizes the 2.4 GHz frequency band to communicate with other devices. The module operates according to the IEEE 802.15.4 specification and can be configured to minimize the possibility of interference with other devices. The module receives RF signals from one or more Crestron devices and can transmit these signals over the air for further processing (depending on the application). Functional Summary 2.4 GHz frequency band, IEEE 802.15.4 specification Range from 3 feet to 100 ft. Operates on one of sixteen available channels to establish optimal signal quality Operations Guide - DOC. 7402A Two-Way RF Transceiver Module: CWD7083 1 Two-Way RF Transceiver Module Crestron CWD7083 Specifications The table below is a summary of specifications for the CWD7083. Specifications of the CWD7083 SPECIFICATION DETAILS Power Requirements 0.825 Watts (5VDC @ 0.167A) Operating Frequency 2400 MHz to 2483.5 MHz (802.15.4 compliant) Operating Ranges* Minimum Distance 3 ft Maximum Distance Indoors (without repeater device) 100 ft Available Channels 16 (numbered 11 through 26 per 802.15.4) Antenna Chip Dimensions Width: 1.88 in (4.77 cm) Height: 0.82 in (2.08 cm) Depth: 0.10 in (0.25 cm) The location and orientation of the module are important factors in the RF performance. With the unit located outside of any metal enclosures, the antenna is adjusted to achieve the best range. The range is dependent on its placement and the building in which it is used. The construction of the building, obstructions, and RF interference from other devices are factors determining the effective range of the unit. To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within 3-5 feet of each other. Physical Description The module, shown below, consists of various components attached to a printed circuit board. Physical View of CWD7083 2 Two-Way RF Transceiver Module with Integral Antenna: CWD7041 Operations Guide - DOC. 7263A Crestron CWD7083 Two-Way RF Transceiver Module CWD7083 Detail Views Power/I-O – An edge connector provides power to the module as well as serial communications between the module and wired devices. Refer to the following table for pin assignments of the module interface connector. Power/I-O Pinout Signals Pin # Signal Pin # +5v 12-16 GND 17-20 GPIO PWMA 21 GPIO PWMB 22 Reserved GPIO Signal Pin # Signal Reserved 29 Reserved GPIO GND 30 SCLK UART RX 31 MOSI UART TX 32 MISO 23 Reserved GPIO 33 CONFIG1 Reserved GPIO 24 RESET 34 CONFIG2 Reserved GPIO 25 Reserved ADC1 35 Reserved GPIO Reserved GPIO 26 Reserved ADC2 36 GND Reserved GPIO 27 Reserved ADC3 62 GND 10 Reserved GPIO 28 GND 63 +5v 11 GND Operations Guide - DOC. 7402A Two-Way RF Transceiver Module: CWD7083 3 Two-Way RF Transceiver Module Crestron CWD7083 Setup For hardware hookup, refer to the “Power/I-O Pinout Signals” table on the previous page, which shows the connection made to the module. NOTE: To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within 3 to 5 feet of each other. Labeling Requirements If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: EROCWD7083” or “Contains FCC ID: EROCWD7083.” Any similar wording that expresses the same meaning may be used. Documentation The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product. The users manual for OEM integrators must include the following information in a prominent location. “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” 4 Two-Way RF Transceiver Module with Integral Antenna: CWD7041 Operations Guide - DOC. 7263A Crestron CWD7083 Two-Way RF Transceiver Module This page is intentionally left blank. Operations Guide - DOC. 7402A Two-Way RF Transceiver Module: CWD7083 5 Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 7402A 05.12 Specifications subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : glin Create Date : 2012:05:14 10:25:11-04:00 Modify Date : 2012:05:14 10:25:11-04:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : Microsoft Word - Manual_CWD7083_Doc7402A 20120514 Creator : glin Producer : Acrobat Distiller 10.0.1 (Windows) Document ID : uuid:8493b961-ab54-47f5-b69b-02bfeba9e9f7 Instance ID : uuid:5041d861-debd-4b05-9dd3-175a1da6fcd1 Page Count : 10EXIF Metadata provided by EXIF.tools