Crestron Electronics GLWRSDIMHSW Zigbee Load Controller User Manual ZUMMESH JBOX IG 7863B Preliminary 1 CS
Crestron Electronics Inc Zigbee Load Controller ZUMMESH JBOX IG 7863B Preliminary 1 CS
User manual
Pre ZUMMESH-JBOX Zūm™ J-Box Load Controller Installation Guide Description The Crestron® junction box-mounted zone controllers deliver intelligent lighting control with essential features for energy efficiency. Available for 20 A switching, 5 A or 16 A 0-10 V dimming, and 20 A plug load control, each ZUMMESH-JBOX model wirelessly connects to Zūm daylight sensors, occupancy sensors, vacancy sensors, keypads, and dimmers (all sold separately) over the Zūm mesh network, providing intelligent lighting control based on the amount of natural light and the presence of people in a space. The Zūm J-Box Zone Controllers offer a powerful lighting control solution for every space within the Zūm network. A basic single-room Zūm system consists of Zūm mesh devices, i.e., dimmers, switches, keypads, and sensors. The Zūm mesh devices in the room communicate directly with each other without the need for a centralized gateway or processor. To monitor or control the room from a centralized Crestron control system, use the ZUMMESH-NETBRIDGE. NOTE: The ZUMMESH-NETBRIDGE requires a J-box device to provide power. SPECIFICATION DETAILS Power Requirements Line Power 100-277 Vac, 50/60 Hz Idle State Power Consumption 1W Expansion Port SKUs ZUMMESH-JBOX-16A-LV / ZUMMESH-JBOX-5A-LV 16 A at 100-277 Vac, 50/60 Hz (20 A, de-rated to 80%) 5 A at 100-277 Vac, 50/60 Hz 0-10V Output 60 mA Sink or Source DIM Load Type LED driver (4-wire), Fluorescent, Incandescent, MLV, ELV Functionality Controlled by keypads, occupancy or vacancy, and daylight sensors. Expansion Port Allows connection of Zūm Network Bridge or Relay Contact Closure Module ZUMMESH-JBOX-20A-SW Switched output 20 A high in-rush (de-rated to 80%), zero cross switching Switch Load Types 0-10 V LED driver, Fluorescent ballast (4-wire), 60 mA max current sink or source Functionality: Controlled by keypads and occupancy or vacancy sensors Expansion Port: Allows connection of Zūm Network Bridge or Relay Contact Closure Module ZUMMESH-JBOX-20A-PLUG Switched output 20 A high in-rush, zero cross switching for control of receptacles Functionality Controlled by occupancy or vacancy sensors to energize receptacles when the room is occupied. Note that the output defaults to energized state after a power cycle. Expansion Port Allows connection of Zūm Network Bridge or Relay Contact Closure Module ZUMMESH-JBOX-PSU Functionality Provides power for Zūm Network Bridge when other J-box devices are not available. Expansion Port Allows connection of Zūm Network Bridge or Relay Contact Closure Module Enclosure Housing Plastic, white, UL® standard 5VA rated Mounting Mounts in a 4˝ x 4˝ junction box via 1/2 in conduit knockout; Rated for mounting in plenum spaces, UL standard 2043 Environmental Temperature 32° to 104 °F (0° to 40 °C) Humidity 10% to 90% RH (noncondensing) Dimensions Height 3.25 in (83 mm) Width 4.17 in (106 mm) Depth Weight 100-277 Vac power from breaker Installation WARNING: To avoid fire, shock, or death, turn off the power at the circuit breaker or fuse and test that the power is off before wiring! Switched Output For quick network setup, use the Zūm app on a smartphone or tablet. Visit the product page on the Crestron website (www.crestron.com) for additional information. Use a QR reader application on your mobile device to scan the QR image. lim Expansion port allows connection of an accessory such as a Zūm Network Bridge (ZUMMESH-NETBRIDGE) or HVAC Contact Closure Module (ZUM-CCO) ZUMMESH-JBOX-20A-PLUG Wiring Additional Resources 1.31 in (33 mm) 0.4 lbs (7 oz) Neutral (white) Hot (black) NOTES: Observe the following points: • Install and use this product in accordance with appropriate electrical codes and regulations. • A licensed electrician should install this product. To install a switch or dimmer, do the following: 1. Turn the power off at the circuit breaker. 3. Mount the J-box device to the J-box. 2. Wire the device as shown in the following diagrams. ZUMMESH-JBOX-5A-LV, ZUMMESH-JBOX-16A-LV, and ZUMMESH-JBOX-20A-SW Wiring ina ry 100-277 Vac power from breaker Neutral (white) Hot (black) 15 or 20 A receptacle Neutral (white) Switched output (red) Hot (black) to unswitched receptacles ZUMMESH-JBOX-PSU Wiring To 0-10 V Controlled load Neutral (white) Switched output (red) 0-10 V dim + (purple) 0-10 V dim - (gray) 100-277 Vac power from breaker Neutral (white) Hot (black) NOTE: The 0–10 V dim - and 0–10 V dim + wires are not present on the ZUMMESH-JBOX-20A-SW. Test the Loads Press the TEST button to toggle the connected loads. Press and hold the TEST button to cycle dim the connected loads (dimmer models only). Pre Step 1b – Expanding an Existing Single-Room Zūm System Basic Room Setup A basic single-room Zūm system consists of Zūm mesh devices, i.e., dimmers, switches, keypads, and sensors. The Zūm mesh devices in the room communicate directly with each other without the need for a centralized gateway or processor. To set up a new single-room Zūm system, do the following: Step 1a: Create a new single-room Zūm system. Step 2: Add Zūm mesh devices to the room. Step 3: Finish creating the single-room Zūm system. To modify an existing Zūm system, do the following: Step 1b: Place the system in Joining mode. Step 2: Add Zūm mesh devices to the room. Step 3: Finish creating the single-room Zūm system. To allow other devices to join the room, place the single-room Zūm system into Joining mode. Joining mode can be enabled from any ac-powered device or battery keypad that is already part of the room. Perform a factory reset when the device is removed from the network or to remove the configuration settings. The device must also be factory reset if the device is being moved to a different system. Expand a Single-Room Zūm System Using a Keypad To enter Joining mode, press and hold both the top and bottom buttons for 5 seconds, wait for the LED to light, and then tap the top button once, and then the bottom button once. To factory reset the device, press and hold the TEST and SETUP button for 10 seconds. Release the button when the LED lights. The LEDs and output will turn on. 5s Step 1a – Creating a Single-Room Zūm System To create a new single-room Zūm system, first form a new room. NOTE: The device that is used to create the room is automatically added to the room. The device does not need to be added to the room. NOTE: A room can be created only from an ac-powered device. SETUP TEST lim Adding Zūm mesh devices to a room is quick and easy. Add devices to the room when the room is in Joining mode. Joining mode is automatically enabled after a single-room Zūm system is started (see Step 1a). Joining mode can also be enabled manually (see Step 1b). The LEDs on all ac-powered devices in the system blink when the system is in Joining mode. 2s or 10s NOTE: A Zūm mesh device can belong to only one room. NOTE: The Zūm mesh device used to create the room is already part of the network. It does not need to be added to the network. To add a J-box dimmer or switch to the room, press the SETUP button 3 times, and then press and hold the SETUP button for 2 seconds. If the device is not factory fresh, hold the button for 10 seconds. Release the button when the LED lights. The LED blinks slowly to indicate that it is part of the room and that the room is still in Joining Mode. SETUP TEST SETUP TEST 2s or 10s 2s or 10s Step 3 - Finishing the Single-Room Zūm System Press any button on a device that has already joined the network to end the setup process (e.g., the top button of a keypad or the SETUP button of a J-box device that is blinking its LED). SETUP TEST This product is Listed to applicable UL® Standards and requirements tested by Underwriters Laboratories Inc. Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses TEST 10s 100-277 Vac power from breaker Neutral (white) Hot (black) TEST Pressing any button on a device that is part of the network takes the system out of joining mode. Joining mode ends automatically after 4 minutes. and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The Zūm Network Bridge enables Zūm device setup from a mobile app and integrates a stand-alone Zūm lighting control system with the Zūm hub (not supplied) for a centrally managed, enterprise-wide lighting control system. The network bridge can be installed to any J-box device. 1. Using a flat-head screwdriver, remove the cover on the J-box device. 2. Ensure that the connector on the network bridge is aligned with the expansion port on the J-box, and then insert the network bridge into the J-box device. The network bridge snaps into place. SETUP SETUP Step 2 - Adding Zūm Mesh Devices to the Room Start a Single-Room System with a J-Box Device Press the SETUP button 5 times, and then press and hold the SETUP button for 2 seconds. If the device is not factory fresh, hold the button for 10 seconds. Release the button when the LED lights. The LED illuminates for 3 seconds and then slowly flashes to indicate that the room is in Joining mode and that other devices can join the room. NOTE: New-in-box devices do not need to be factory reset before joining a system. Expand a Single-Room Zūm System Using a J-box Device To enter Joining mode, tap the SETUP button 2 times, and then tap the TEST button. NOTE: This can be performed on only one device in the room. Start a New Single-Room System with a Keypad, Dimmer, or Switch Press the bottom button 5 times, and then press and hold the bottom button for 2 seconds. If the device is not factory fresh, hold the button for 10 seconds. Release the button when the LED lights. The LED illuminates for 3 seconds and then slowly flashes to indicate that the room is in Joining mode and that other devices can join the room. Install Network Bridge Factory Reset ina ry This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Industry Canada (IC) Compliance Statement The product warranty can be found at www.crestron.com/warranty. CAN ICES-3(B)/NMB-3(B) The specific patents that cover Crestron products are listed at patents.crestron.com. Certain Crestron products contain open source software. For specific information, please visit If necessary, the network bridge can be easily removed. To remove the network bridge, do the following: 1. Between the J-box and the J-box device, press the side of the network bridge with your thumb away from the J-box. 2. While pressing on the side of the network bridge, slightly lift the network bridge up and out of the J-box device. The network bridge should easily remove from the J-box device. www.crestron.com/opensource. Crestron, the Crestron logo,and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. This document was written by the Technical Publications department at Crestron. ©2017 Crestron Electronics, Inc. Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Installation Guide - DOC. 7863B (2048125) 11.17 Specifications subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2017:11:03 15:44:19-04:00 Creator : Adobe Illustrator CC 2015.3 (Windows) Creator Version : 21.0.2 Modify Date : 2017:11:03 15:48:09-04:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Format : application/pdf Title : ZUMMESH-JBOX_IG_7863B_Preliminary_1_CS Metadata Date : 2017:11:03 15:48:09-04:00 Creator Tool : Adobe Illustrator CC 2015.3 (Windows) Thumbnail Width : 256 Thumbnail Height : 192 Thumbnail Format : JPEG Thumbnail Image : (Binary data 10124 bytes, use -b option to extract) Instance ID : uuid:916151fc-80f6-4de3-b55e-efddec4ed5f1 Document ID : xmp.did:8e753a86-292c-104a-b31b-888e14f03b41 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : uuid:4197ff52-608f-4167-8888-c17dae685b04 Derived From Document ID : xmp.did:5b483447-38ed-9949-bccb-38362fdfb5e5 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:5D2E25593251E111B01C938CD82A7350, xmp.iid:8e753a86-292c-104a-b31b-888e14f03b41 History When : 2012:02:06 21:20:48-05:00, 2017:11:03 15:44:11-04:00 History Software Agent : Adobe Illustrator CS5.1, Adobe Illustrator CC 2015.3 (Windows) History Changed : /, / Manifest Link Form : EmbedByReference Manifest Reference File Path : C:\Users\csantimauro\Documents\Chris S\Tasks\ZUMMESH-JBOX_IG_7863B\DOCS\barcode.png Manifest Reference Document ID : 0 Manifest Reference Instance ID : 0 Ingredients File Path : C:\Users\csantimauro\Documents\Chris S\Tasks\ZUMMESH-JBOX_IG_7863B\DOCS\barcode.png Ingredients Document ID : 0 Ingredients Instance ID : 0 Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 17.000000 Max Page Size H : 11.000000 Max Page Size Unit : Inches Font Name : Arial-ItalicMT, Arial-BoldMT, Arial-BoldItalicMT, ArialMT, HelveticaNeueLTStd-Md, HelveticaNeueLTStd-BdCn, HelveticaNeueLTStd-LtIt, HelveticaNeueLTStd-Bd, HelveticaNeueLTStd-Roman, HelveticaNeueLTStd-Hv, MyriadPro-Regular, TimesNewRomanPSMT Font Family : Arial, Arial, Arial, Arial, Helvetica Neue LT Std, Helvetica Neue LT Std, Helvetica Neue LT Std, Helvetica Neue LT Std, Helvetica Neue LT Std, Helvetica Neue LT Std, Myriad Pro, Times New Roman Font Face : Italic, Bold, Bold Italic, Regular, 65 Medium, 77 Bold Condensed, 46 Light Italic, 75 Bold, 55 Roman, 85 Heavy, Regular, Regular Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type Font Version : Version 6.90, Version 5.08, Version 6.90, Version 5.22, Version 2.035;PS 002.000;hotconv 1.0.51;makeotf.lib2.0.18671, Version 2.035;PS 002.000;hotconv 1.0.51;makeotf.lib2.0.18671, Version 2.035;PS 002.000;hotconv 1.0.51;makeotf.lib2.0.18671, Version 2.035;PS 002.000;hotconv 1.0.51;makeotf.lib2.0.18671, Version 1.047;PS 001.103;Core 1.0.38;makeotf.lib1.6.5960, Version 2.035;PS 002.000;hotconv 1.0.51;makeotf.lib2.0.18671, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 5.22 Font Composite : False, False, False, False, False, False, False, False, False, False, False, False Font File Name : ariali.ttf, arialbd_0.ttf, arialbi.ttf, arial_2.ttf, HelveticaNeueLTStd-Md_2.otf, HelveticaNeueLTStd-BdCn_4.otf, HelveticaNeueLTStd-LtIt_3.otf, HelveticaNeueLTStd-Bd_5.otf, HelveticaNeueLTStd-Roman_2.otf, HelveticaNeueLTStd-Hv_2.otf, MyriadPro-Regular_1.otf, times_1.ttf Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group, Grays, Brights Swatch Group Type : 0, 0, 0 Swatch Colorant Swatch Name : White, Black, CMYK Red, CMYK Yellow, CMYK Green, CMYK Cyan, CMYK Blue, CMYK Magenta, C=15 M=100 Y=90 K=10, C=0 M=90 Y=85 K=0, C=0 M=80 Y=95 K=0, C=0 M=50 Y=100 K=0, C=0 M=35 Y=85 K=0, C=5 M=0 Y=90 K=0, C=20 M=0 Y=100 K=0, C=50 M=0 Y=100 K=0, C=75 M=0 Y=100 K=0, C=85 M=10 Y=100 K=10, C=90 M=30 Y=95 K=30, C=75 M=0 Y=75 K=0, C=80 M=10 Y=45 K=0, C=70 M=15 Y=0 K=0, C=85 M=50 Y=0 K=0, C=100 M=95 Y=5 K=0, C=100 M=100 Y=25 K=25, C=75 M=100 Y=0 K=0, C=50 M=100 Y=0 K=0, C=35 M=100 Y=35 K=10, C=10 M=100 Y=50 K=0, C=0 M=95 Y=20 K=0, C=25 M=25 Y=40 K=0, C=40 M=45 Y=50 K=5, C=50 M=50 Y=60 K=25, C=55 M=60 Y=65 K=40, C=25 M=40 Y=65 K=0, C=30 M=50 Y=75 K=10, C=35 M=60 Y=80 K=25, C=40 M=65 Y=90 K=35, C=40 M=70 Y=100 K=50, C=50 M=70 Y=80 K=70, C=0 M=0 Y=0 K=100, C=0 M=0 Y=0 K=90, C=0 M=0 Y=0 K=80, C=0 M=0 Y=0 K=70, C=0 M=0 Y=0 K=60, C=0 M=0 Y=0 K=50, C=0 M=0 Y=0 K=40, C=0 M=0 Y=0 K=30, C=0 M=0 Y=0 K=20, C=0 M=0 Y=0 K=10, C=0 M=0 Y=0 K=5, C=0 M=100 Y=100 K=0, C=0 M=75 Y=100 K=0, C=0 M=10 Y=95 K=0, C=85 M=10 Y=100 K=0, C=100 M=90 Y=0 K=0, C=60 M=90 Y=0 K=0 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Cyan : 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 15.000000, 0.000000, 0.000000, 0.000000, 0.000000, 5.000000, 20.000000, 50.000000, 75.000000, 85.000000, 90.000000, 75.000000, 80.000000, 70.000000, 85.000000, 100.000000, 100.000000, 75.000000, 50.000000, 35.000000, 10.000000, 0.000000, 25.000000, 40.000000, 50.000000, 55.000000, 25.000000, 30.000000, 35.000000, 40.000000, 40.000000, 50.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 85.000000, 100.000000, 60.000000 Swatch Colorant Magenta : 0.000000, 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 90.000000, 80.000000, 50.000000, 35.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000000, 30.000000, 0.000000, 10.000000, 15.000000, 50.000000, 95.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 95.000000, 25.000000, 45.000000, 50.000000, 60.000000, 40.000000, 50.000000, 60.000000, 65.000000, 70.000000, 70.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 75.000000, 10.000000, 10.000000, 90.000000, 90.000000 Swatch Colorant Yellow : 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 0.000000, 0.000000, 90.000000, 85.000000, 95.000000, 100.000000, 85.000000, 90.000000, 100.000000, 100.000000, 100.000000, 100.000000, 95.000000, 75.000000, 45.000000, 0.000000, 0.000000, 5.000000, 25.000000, 0.000000, 0.000000, 35.000000, 50.000000, 20.000000, 40.000000, 50.000000, 60.000000, 65.000000, 65.000000, 75.000000, 80.000000, 90.000000, 100.000000, 80.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 95.000000, 100.000000, 0.000000, 0.003100 Swatch Colorant Black : 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000000, 30.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 0.000000, 0.000000, 10.000000, 0.000000, 0.000000, 0.000000, 5.000000, 25.000000, 40.000000, 0.000000, 10.000000, 25.000000, 35.000000, 50.000000, 70.000000, 100.000000, 89.999400, 79.998800, 69.999700, 59.999100, 50.000000, 39.999400, 29.998800, 19.999700, 9.999100, 4.998800, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.003100 Producer : Adobe PDF library 15.00 Page Layout : SinglePage Page Count : 2EXIF Metadata provided by EXIF.tools