Dongguan Newmen Electronics Technology MS225OR Lenovo Wireless Mouse User Manual manual
Dongguan Newmen Electronics Technology Co.,LTD Lenovo Wireless Mouse manual
manual
MS-225OR 210*148MM User Manual Description of keys and DPI adjusting Left key Right key Scrolling wheel Package contents Wireless Optical Mouse USB receiver 2 AAA alkaline batteries User manual Installing the battery (Diagram 1) ON/OFF switch Battery cover Low-voltage alarming function When battery has been used for some time and discover the LED light in "DPI-adjusting key" blinks automatically, which reminds you that battery's voltage is becoming low, suggested you replace the battery with new one. Position for storing receiver (Diagram 1) (Diagram 2) Whenever new batteries are installed, make sure that they are fresh 1.5V AAA batteries. A)Remove the battery cover. B) Insert two AAA batteries into the battery compartment, make sure to properly orient the positive (+) and negative (-) ends as specified by the marks in the battery compartment. Replace the battery cover and make sure it is locked. C)Switch on the mouse, the LED in bottom of mouse will blink. Installing the receiver (Diagram 2) The codes of receiver and mouse were successfully connected in factory. User can directly use the complete set of products, no worry about the code connecting. A)Insert receiver into USB port of PC, the computer system will automatically detect it and prepare it for full operation. B)The mouse may use then. If the user wrongly operates, please redo the above operating procedures. "ON/OFF" switch (Diagram 1) Without using the mouse, user may turn off it by "ON/OFF" switch for saving battery power. System requirements Windows 2000/XP/Vista/7 Specifications and functions 1. USB nano receiver can be stored inside battery compartment 2. 2.4GHz, operating distance up to 8 meters 3. Power ON/OFF function 4. Low-voltage alarming function 5. Resolution: 1200DPI adjustable (1) 15.21 statement changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the userâs authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of FCC RF Rules. Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Canada Statement This Device complies with RSS-210 of the IC Rules; Operation is subject to the following two conditions: (1). This device may not cause interference and (2). This device must accept any interference received,, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Create Date : 2010:08:26 09:36:57Z Creator Tool : CorelDRAW Version 9.397 Modify Date : 2010:09:07 11:03:22+08:00 Metadata Date : 2010:09:07 11:03:22+08:00 Format : application/pdf Creator : * Title : MS-132 168 146 150 152 148 158BT˵Ã÷Êé-ÐÂ.cdr Producer : Corel PDF Engine Version 9.397 Document ID : uuid:d66afacd-0f6e-4d74-8f6d-03928033d8dd Instance ID : uuid:d651f338-84e5-4262-9f77-3a28e03fddb9 Has XFA : No Page Count : 2 Author : *EXIF Metadata provided by EXIF.tools