ELITEGROUP COMPUTER SYSTEMS TABC8TA1 Wireless Motherboard User Manual

ELITEGROUP COMPUTER SYSTEMS CO., LTD Wireless Motherboard Users Manual

Contents

Users Manual

TA80TA1
Motherboard Guide
1
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for
help.
CAUTION:
Any changes or modifications not expressly approved by the
grantee of this device could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20 cm
2
from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and
installers must be provide with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure
compliance.
End Product Labeling
This transmitter module is authorized only for use in device where
the antenna may be installed such that 20cm may be maintained
between the antenna and users. The final end product must be
labeled in a visible area with the following: "Contains FCC ID:
WL6-TABC8TA1”
Information for the OEMs and Integrators
The following statement must be included with all versions of this
document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other
restrictions.
This radio transmitter FCC ID: WL6-TABC8TA1 has been approved
by FCC to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for
each antenna type indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.
Antenna List
No.
Manufacturer
Part No.
Antenna
Type
Peak Gain
1 JEM 13H130-
JV8070
PCB
Antenna
2.85 dBi for 2.4GHz
2 WGT 13H130-
JV8050
PCB
Antenna
1.77 dBi for 2.4GHz
Note: The antenna connector is I-PEX type.
3
Motherboard layout
Main components
No.
Name No.
Name
A Charger IC D WiFi/BT IC
B CPU+PMIC+DDR+
EMMC+CODEC
E Rear facing
camera
C
GPS IC F Microphone
4
System connectors
No.
Name No.
Name
1 Battery Connector 5 Speaker Connectors
2 LCD Connector 6 Side Key FPC
Connector
3 GPS Antenna
Connector 7 TP Connector
4 WiFi Antenna
Connector
I/O Ports
5
No.
Name No.
Name
1 Ultrastick Connector 4 T-Flash Connector
2 Micro USB Connector
5 Mini HDMI port
3 Audio Jack
6
Features
Processor
IntelBayTrail-TZ3735E
Quad core
Base 1.33 GHz, Burst to
1.83GHz, 2MB L2 Cache
Memory DDR3L-RS 1333, 1 x 32-bits
1GB (Default) / 2GB (Optional)
Graphics Intel HD Graphics (Gen 7 gfx)
Max resolution upto1280x800
Storage Single eMMC v4.5.1
Default 16 GB
Wireless
Wi-Fi 802.11 b/g/n
Bluetooth 3.0 w/o high speed
supported
Display MIPI interface
Support 10-point multi-touch
Cameras
Control
FrontCamera:2.0M
Rear Camera:5.0M
Antenna 802.11b/g,n, BT: 2.4GHz; GPS
7
Input/Output
1 x MicroUSB 2.0, OTG port
(Type A/B)
1 x Mic/head phone jack combo
(American type)
1 x Micro HDMI 1.4
1 x Micro SD card slot (Support
128M-32G TF Card)
1 x Analog MIC
Speaker & Mic
Build-in Speaker x 2
Internal Analog MIC x 1

Navigation menu