FANGTEC XHT-08X Bluetooth Module User Manual Features
FANGTEC CORP. Bluetooth Module Features
FANGTEC >
User Manual
Bluetooth Module Specification Features Bluetooth V4.0 Class2 (also compliant Bluetooth 2.1+EDR) Fully qualified Bluetooth v4.0 specification system Support for Bluetooth v3.0 only available with CSR8510A04 Dual-mode Bluetooth /Bluetooth low energy Draft Bluetooth low energy HID boot mode support Full-speed Bluetooth operation with full piconet and scatternet support Integrated balun No external regulators required for USB supply operation Full- speed USB 2.0 interface Green (RoHS compliant and no antimony or halogenated flame retardants) Design optimised for low-cost PCB manufacture OS supported: windows 7, vista, XP Plug and play Bluetooth low energy Support Heart rate belt, Find me , Proximity , Generic Attribute Profile Bluetooth 2.1+EDR Support A2DP, AVRCP, DUN-GW, HSP , HFP A2DP AVTCP, FTP, OPP, Audio-GW, FAX, BPP and etc. Dual-mode Bluetooth low energy radio USB dongle Full speed USB 2.0 interface Bluetooth end product Bluetooth low energy Support Heart rate belt, Find me , Proximity , Generic Attribute Profile Bluetooth 2.1+EDR Support A2DP, AVRCP, DUN-GW, HSP , HFP A2DP AVTCP, FTP, OPP, Audio-GW, FAX, BPP and tec. RoHS compliant BQB, CE, CE and FCC General Description BlueCore CSR8510 A06 WLSCP is a product from CSR's Connectivity Centre. It is a single-chip radio and baseband IC for Bluetooth 2.4 GHz systems including EDR to 3 Mbps. Dedicated signal and baseband processing is included for full Bluetooth operation. CSR designed CSR8510 WLCSP to reduce PCB area and the number of external components , including no requirement for an external balun. This ensures that production costs are minimised. Applications PC notebooks , netbooks and desktops TV set-top boxes USB Bluetooth dongles Bluetooth designs requiring the USB interface and an HCI interface Bluetooth low energy Device Details *Bluetooth low energy Dual-mode Bluetooth low energy radio Support for Bluetooth basic rate/EDR and low energy connections 3 Bluetooth low energy connections at the same time as basic rate A2DP *Bluetooth Radio Integrated balun (50Ω impedance in TX and RX modes) No external trimming is required in production Bluetooth v4.0 specification compliant *Bluetooth Transmitter 9.5dBm RF transmit power with level control from on-chip 6-bit DAC over a dynamic range>30dB Class 1,Class 2 and Class 3 support without need for external PA or TX/RX switch *Bluetooth Receiver Receive sensitivity of -91 dBm for basic rate Integrated channel filters Digital demodulator for improved sensitivity and co-channel rejection Real-time digitised RSSI available on HCI interface Fast AGC for enhanced dynamic range Channel classification for AFH *Bluetooth Stack CSR's Bluetooth Protocol Stack runs on the on-chip MCU: Support for Bluetooth v4.0 specification features : Master and slave operation Including encryption Software stack in firmware includes : GAP L2CAP Security Manager Attribute protocol Attribute profile Bluetooth low energy profile support *Physical Interfaces Full-speed (12Mbps) USB 2.0 interface General Specification: Bluetooth Specification Standard Bluetooth V4.0 Profiles Bluetooth low energy Dual-mode Bluetooth Frequency Band 2.402G-2.480G Sensitivity -90dBm@.01%BER RF TX Power 0.68dBm for BR/EDR; -0.82dBm for BLE Power Supply Voltage Working Current Standby Current (Connected ) 5V DC(MAX5.75V) Depends on profiles, 22mA typical 0.4uA Operating Environment Temperature -20℃ to +70℃ Humidity 10%-90% Non- Condensing FCC Statements (OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module. For 15 B (§15.107 and if applicable §15.109) compliance, the host manufacturer is required to show compliance with 15 while the module is installed and operating. Furthermore the module should be transmitting and the evaluation should confirm that the module's intentional emissions (15C) are compliant (fundamental / out-of-band). Finally the integrator has to apply the appropriate equipment authorization (e.g. Verification) for the new host device per definition in §15.101. Integrator is reminded to assure that these installation instructions will not be made available to the end-user of the final host device. The final host device, into which this RF Module is integrated" has to be labeled with an auxiliary label stating the FCC ID of the RF Module, such as "Contains FCC ID: 2AOQ8-XHT-08X "This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation." "Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment." the Integrator will be responsible to satisfy SAR/ RF Exposure requirements, when the module integrated into the host device. Module statement The single-modular transmitter is a self-contained, physically delineated, component for which compliance can be demonstrated independent of the host operating conditions, and which complies with all eight requirements of § 15.212(a)(1) as summarized below. 1) The radio elements have the radio frequency circuitry shielded. 2) The module has buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal. 3) The module contains power supply regulation on the module. 4) The module contains a permanently attached antenna. 5) The module demonstrates compliance in a stand-alone configuration. 6) The module is labeled with its permanently affixed FCC ID label. 7) The module complies with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. 8) The module complies with RF exposure requirements. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 5 Language : zh-CN Tagged PDF : Yes Title : Features Author : 成工 Creator : Microsoft® Office Word 2007 Create Date : 2018:01:26 15:08:09+08:00 Modify Date : 2018:01:26 15:08:09+08:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools