Fu Hsing A21 Access Control - Electronic Interconnected Lock User Manual
Taiwan Fu Hsing Industrial Co., Ltd. Access Control - Electronic Interconnected Lock Users Manual
Fu Hsing >
Users Manual
Directory Welcome to TOUCH-BOLT System………………….. Introduction….........…………………………………………................................. System Requirement…………………………………………………………….. Minimum Requirement……………..……………………………………… Recommended Specification……………..……………………………. Supported input/output Device…..…………………………………. Start and Close the Application………………………………………. User Guide……………………………………………………...…......................... Project Management……………….……………………………………. Construction Key……………………………………………………………….. Create a Programming Key…………………………………….. 01 02 Project Management 03 Please refer to the user guide for more details. Project Management Please refer to the user guide for more details. 04 Project Management 05 Please refer to the user guide for more details. Construction Key Please refer to the user guide for more details. 06 Construction Key 07 Please refer to the user guide for more details. DECLARATIONS AND SAFETY STATEMENTS FEDERAL COMMUNICATIONS COMMISSION STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. IC REGULATIONS RÈGLEMENTS D'IC This device complies with Industry Canada licence-exempt RSS-210, RSS-247 standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 08
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2015:11:16 14:51:52+08:00 Metadata Date : 2015:11:16 14:51:53+08:00 Modify Date : 2015:11:16 14:51:53+08:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:9e6d36cb-c8d9-8e4b-812e-e0351e2486c8 Original Document ID : xmp.did:01801174072068118A6DA0B08B8825E6 Document ID : xmp.id:0780117407206811822AC55BEBFD3C06 Rendition Class : proof:pdf History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2015:11:16 14:51:52+08:00 Derived From Instance ID : xmp.iid:0680117407206811822AC55BEBFD3C06 Derived From Document ID : xmp.did:01801174072068118A6DA0B08B8825E6 Derived From Original Document ID: xmp.did:01801174072068118A6DA0B08B8825E6 Derived From Rendition Class : default Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 9 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools