Fujitsu Australia WL0006 LifeBook ST Series Tablet PC's User Manual BroadcomUserManual2

Fujitsu Australia Ltd LifeBook ST Series Tablet PC's BroadcomUserManual2

Contents

Users Manual

FCC ID: QK3-WL0006 IC ID: 337H-WL0006 Report No. M030531_Certification_Albion2 This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMC Technologies Pty Ltd - Report No. M030531_Certification_Albion2 APPENDIX J - User Manual (supplied to end users)
54Mbps 802.11g Wireless LAN Card User’s Manual
Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of the seller. The seller provides this documentation without warranty, term, or condition of any kind. The seller may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. Other product and company names herein may be trademarks of their respective owners.  2002 All rights reserved. Rev: 01 January 2003
I Contents About This Manual............................................................................................................................................V Chapter 1 Introduction.................................................................................................................................... 1 Wireless LAN Basics ....................................................................................................................................... 2 Local Area Network (LAN)......................................................................................................................................................................... 2 Ad-Hoc Mode................................................................................................................................................................................................. 3 Infrastructure Mode ..................................................................................................................................................................................... 4 Roaming.......................................................................................................................................................................................................... 5 Chapter 2 Installing the Wireless LAN Card.................................................................................................... 7 System Requirements...................................................................................................................................... 7 Installing Wireless LAN Driver and Software...................................................................................................... 8 Chapter 3 Using Broadcom Wireless Configuration Utility............................................................................11 Accessing Broadcom Wireless Configuration Utility...........................................................................................12 Notice When Assessing Broadcom Utility under Windows XP...........................................................................................................12 Wireless Networks Tab ...................................................................................................................................15 Connecting to an Existing Wireless Network.........................................................................................................................................15 Configuring a New Wireless Network Connection...............................................................................................................................17
54Mbps 802.11g Wireless LAN Card II Configuring an Existing Wireless Network Connection......................................................................................................................20 Specifying a Network Type to Access......................................................................................................................................................21 Link Status Tab..............................................................................................................................................22 Statistics........................................................................................................................................................25 Site Monitor....................................................................................................................................................26 Advanced Site Monitor...............................................................................................................................................................................29 Diagnostics Tab .............................................................................................................................................32 Information Tab ..............................................................................................................................................35 Chapter 4 Windows XP Wireless Zero Configuration Utility ..........................................................................37 Connecting to an Access Point or Wireless LAN Card ........................................................................................................................37 Viewing Wireless Connection Status.......................................................................................................................................................39 Configuring Your Wireless Properties....................................................................................................................................................40 Chapter 7 Troubleshooting............................................................................................................................47 Radio Interference..........................................................................................................................................47 Card Not Detected..........................................................................................................................................48 Cannot Connect to Another Wireless LAN Card................................................................................................48 Poor Link Quality............................................................................................................................................49 Cannot Connect to Access Point .....................................................................................................................49 Appendix A Limited Warranty........................................................................................................................51 Wireless LAN Hardware..................................................................................................................................51 Wireless LAN Software ...................................................................................................................................52 Appendix B Regulatory Compliance..............................................................................................................53
Contents III FCC Part 15 Declaration of Conformity (DoC) ..................................................................................................53 FCC Rules and Regulations - Part 15 ..............................................................................................................54 FCC Radiation Exposure Statement ................................................................................................................55 Appendix C Setting Up TCP/IP.......................................................................................................................57 For Windows 98/ME .......................................................................................................................................57 For Windows 2000/XP ....................................................................................................................................59 Appendix D Specifications...............................................................................................................................63 Glossary ..........................................................................................................................................................65
54Mbps 802.11g Wireless LAN Card IV List of Figures Figure 1-1 Peer-to-Peer Group (Ad-Hoc Mode).............................................................................................3 Figure 1-2 Infrastructure Mode ...................................................................................................................4 Figure 1-3 Roaming Across Multiple Access Points.......................................................................................5 Figure 3-13 Windows XP Configuration Utility-Connect to Wireless Network.................................................38 Figure 3-14 Windows XP- Connection Status .............................................................................................40 Figure 3-15 Windows XP Connection Properties -General...........................................................................41 Figure 3-16 Windows XP Connection Properties-Wireless Networks............................................................42 Figure 3-17 Windows XP-Add Preferred Networks......................................................................................43 Figure 3-18 Windows XP Configuration Utility-Set up Network to Aceess .....................................................45 Figure 3-19 Windows XP Connection Properties -Authentication..................................................................46
Contents V About This Manual This manual was written for the following types of wireless adapter: • PC Card • PCI Card • Mini PCI Card For brevity, throughout this manual Wireless LAN Card is used to indicate both types. Also, the following terms/abbreviations are used interchangeably: • Access Point – AP • Peer-to-Peer – Ad Hoc • Wireless LAN – WLA N • Ethernet network – LAN – network This User’s Manual contains information on how to install and configure your Wireless LAN Card. From now on, we will guide you through the correct configuration steps to get your device up and run.
54Mbps 802.11g Wireless LAN Card VI
1 Chapter 1 Introduction This Wireless LAN Card is an IEEE 802.11g wireless LAN adapter. 802.11g is the latest in the series of 802.11 specifications for wireless local area networks (WLANs) and provides data transfer of up to 54 Mbps. Since 802.11g operates on the same frequency of 2.4 GHz as 802.11b, so it is backwards compatible with existing Wi-Fi devices! It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operating in 2.4GHz Direct Sequence Spread Spectrum (DSSS) radio transmission, the Wireless LAN Card transfers data at speeds up to 54Mbps. Both Ad-Hoc and Infrastructure mode are supported. For network security concern, 64/128-bit Wired Equivalent Protection (WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any 802.11b/g networks.
54Mbps 802.11g Wireless LAN Card 2 Wireless LAN Basics This section conations some Wireless LAN basics to help you better understand how the product work together to create a wireless network. Local Area Network (LAN) Simply put, a LAN is a network that exists in a relatively limited area. A network is two or more computers connected together sharing files and peripheral devices such as printers. The Wireless LAN Card allows you to interact with other computers without having to run cables normally associated with networks. This lets you move your computer around while staying connected to your network. There are two ways to use the Wireless LAN Card. One way is to connect directly to one or more Wireless LAN Card equipped computers, forming an Ad-Hoc wireless network. The second way is to connect to an Access Point that gives you access to an existing wired LAN, forming an Infrastructure wireless network.
Chapter 1 Introduction 3 Ad-Hoc Mode The Ad-Hoc Group offers peer-to-peer connections between workstations, allowing communication between computers within range that have an 802.11g DSSS compatible PC card installed. A wireless Ad-Hoc network can also access a wired LAN’s TCP/IP service (such as e-mail and the Internet) by using a TCP/IP software router on an Ethernet equipped PowerBook or notebook. Figure 1-1 Ad-Hoc Mode
54Mbps 802.11g Wireless LAN Card 4 Infrastructure Mode The Infrastructure network uses an AP or several APs as a gateway, linking the wireless network to a wired LAN. As a result, portable workstations or desktops on your wireless network have access to all of the features of your wired LAN including e-mail, Internet access, network printers and files server. Figure 1-2 Infrastructure Mode
Chapter 1 Introduction 5 Roaming Multiple Access Points can be installed to extend the wireless service coverage area for seamless wireless access. Within an extended service area, all Access Points and wireless clients must have the same Service Set Identity (SSID). Roaming among different Access Points is controlled automatically to maintain the wireless connectivity at all times. Figure 1-3 Roaming Across Multiple Access Points
7 Chapter 2 Installing the Wireless LAN Card This chapter describes the installation process for the driver and software for the Wireless LAN Card. Proper driver installation is to allow the device to operate on your host computer while the utility software, Broadcom Wireless Configuration Utility, is to help you configure and monitor your Wireless LAN Card. System Requirements To use the Wireless LAN Card, your computer must meet the following minimum requirements: l Pentium-class PC,300MHz or better recommended l 64 MB of RAM, additional memory recommended l Hard disk space at least 30 Mbytes l Windows 98(SE)/Me/2000/XP l UL listed I.T.E. computers
54Mbps 802.11g Wireless LAN Card 8 Installing Wireless LAN Driver and Software Follow these steps to install the Wireless LAN Card driver and software: Caution: Do not connect the Wireless LAN Card device to your computer before installing its driver. If this happens, the Windows PnP function will detect the wireless adapter and issue a dialog box requesting for its driver. Click Cancel to quit the wizard and unplug the Wireless LAN Card. 1. Close all Windows programs that are running. Insert the provided Software Utility CD into your CD-ROM drive. Run setup.exe from the Driver folder of the Software Utility CD. 2. If the wireless adapter is not yet inserted into your computer, click Yes. Otherwise click No to remove the device. Then restart your system and run setup.exe again.
Chapter 2 Installing the Wireless LAN Card 9 3. When the welcome screen pops up, click Next. 4. Upon hardware detection, Windows OS hardware wizard will appear requesting for the driver. Just follow the on-screen instructions to proceed. 5. Click Finish when the following screen appears.
54Mbps 802.11g Wireless LAN Card 10 Now you are done with the installation procedure. The provided Broadcom Wireless Configuration Utility should be launched automatically with its icon appearing on the right side of the taskbar. Proceed to next chapter to configure or fine-tune your Wireless LAN Card settings. Note: If you need to set up the TCP/IP address or the subnet mask, refer to “Appendix C Setting Up TCP/IP” for details.
11 Chapter 3 Using Broadcom Wireless Configuration Utility Once your wireless adapter software is properly installed, the provided Broadcom Wireless Configuration Utility is ready for use. The utility comes with six tabs. The Wireless Networks tab allows to configure your wireless connection. The Link Status tab displays the current link status. The Site Monitor tab allows to monitor available networks. The Diagnostic tab allows to perform diagnostics. The utility information is displayed on the Information tab. The Statistics tab displays the statistics and status information pertaining to your Wireless LAN Card. See the ensuing subsections for instructions to launch the utility and description of each tab. Note: If you are using Windows XP, you can also use the Windows XP-included wireless utility to configure and monitor your wireless network. For more information on using Windows wireless utility, please refer to Windows XP on-line help.
54Mbps 802.11g Wireless LAN Card 12 Accessing Broadcom Wireless Configuration Utility You can access the Broadcom Wireless Configuration Utility by any of the following methods: • Double-click the Broadcom Wireless Utility icon on the system tray and then click Advanced. • Right-click the tray icon and select Open Utility from its context menu. • Under Control Panel, double-click the Broadcom Wireless Utility icon. The Broadcom Wireless Configuration Utility screen pops up with six available tabs: Wireless Network, Link Status, Statistics, Site Monitor, Diagnostics and Information. Please see the appropriate section which describes each tab item. Notice When Assessing Broadcom Utility under Windows XP Aside from using Broadcom Wireless Configuration Utility for wireless network configuration, Windows XP includes a Wireless Network Connection utility to configure your wireless adapter. By default, your wireless adapter is controlled by Windows XP-included wireless utility.
Chapter 3 13 You can choose to configure your wireless network via either the Broadcom Wireless Configuration Utility or Windows XP-included wireless utility. Using Broadcom Wireless Configuration Utility To use Broadcom Wireless Configuration Utility for configuration purpose, you should disable the Windows XP-included wireless utility by these steps: 1. Double-click the Broadcom wireless icon on system tray and click the Wireless Networks tab. Or double-click the Windows wireless icon and then click Advanced (or Properties) > Wireless Networks. 2. On the Wireless Networks tab, uncheck the Use Windows to configure my wireless network settings box and click OK. This will restore the Wireless Networks tab in Broadcom Wireless Configuration Utility. Windows wireless icon Broadcom wireless icon
54Mbps 802.11g Wireless LAN Card 14 Reverting back to Windows XP-included Wireless Utility To revert back to using Windows XP-included wireless utility, double-click the Windows wireless icon (not the Boradcom icon) and then click Advanced (or Properties). Click the Wireless Networks tab and check the Use Windows to configure my wireless network settings box and click OK.
Chapter 3 15 Wireless Networks Tab Wireless Networks tab allows to do the following task: • Connecting to an Existing Wireless Network • Configuring a New Wireless Network Connection • Specifying a Network Type to Access See the appropriate subsection according to your need. Connecting to an Existing Wireless Network To connect to an existing Access Point/Wireless LAN Card, take the following steps: 1. Double-click the Broadcom Wireless Utility icon on the system tray. 2. When the Connect to Wireless Network window pops up, you will see all the wireless networks available in the air. Under Available networks, select the wireless network you want to connect to.
54Mbps 802.11g Wireless LAN Card 16 3. If the target wireless network has been set with WEP key, you must enter the same WEP key in the Network key field. Otherwise, this field is dimmed and you do not need to set up the WEP key. 4. Click Connect, then you will join the target network and this dialog window will disappear. When your wireless connection is established, the connection icon may appear as below:
Chapter 3 17 Configuring a New Wireless Network Connection When you open the Connect to Wireless Network window, a network which does not broadcast its network name will not appear under Available networks. To connect to an existing network but not appear under Available networks, take the following steps: 1. In Connect to Wireless Network window, click Advanced to launch the Broadcom Wireless Configuration Utility window. Then click Add under Preferred networks section.
54Mbps 802.11g Wireless LAN Card 18 2. In the Wireless Network Properties window, configure the settings below: Network name (SSID): Specifies the name of the Wireless LAN group you want to participate in. Network Authentication (Shared mode): Specifies the authentication type. You should use the same setting as the other wireless stations in your target wireless network. Wireless network key (WEP): If a network key is required, do the following: • If the WEP key is automatically provided (for example, the key is stored on the wireless network adapter given to you by your network administrator), check The key is provided for me automatically check box. • If the WEP key is not automatically provided for you, leave The key is provided for me automatically check box blank and then enter the key in the Network key field. When entering the key, the Key format and Key length are changed automatically according to the format and length of the characters you entered. When using Hexadecimal format, only digits 0-9 and letters a-f, A-F are allowed. Make sure to enter the character matching the required key format and length as below: ASCII characters Hexadecimal digits 40 bit 5 alphanumeric characters 10 hexadecimal digits 104 bit 13 alphanumeric characters 26 hexadecimal digits
Chapter 3 19 Key index (advanced): Specifies the key index value. You can specify up to four keys (the key index are 0, 1, 2 and 3). Note: Contact your network administrator if you are unsure about the WEP setting. Ad Hoc/ Infrastructure Network: If the network you are configuring is an Ad Hoc network, check This is a computer-to-computer (ad hoc) network… check box. Otherwise leave it unchecked for Infrastructure network connection. 3. After entering required fields, click OK to exit this window.
54Mbps 802.11g Wireless LAN Card 20 Your newly configured network will be added under Preferred networks. Your wireless adapter will attempt to connect preferred networks in the order in which they appear in the list. You can change the order of preferred network by selecting the network that you want to move and clicking the Move up or Move down button. Note that in the Preferred networks list, an Ad-hoc network can not be moved to a higher position than an Infrastructure network. If you want to connect to Ad Hoc network only, see “Specifying a Network Type to Access” for instructions. Configuring an Existing Wireless Network Connection On the Wireless Networks tab, if your target network appears under the Available networks or Preferred networks list but you cannot connect to it, you may want to review or reconfigure the settings. If this is the case, just select your target network and then click Configure (for Available networks) or Properties (for Preferred networks) to open the properties window. Then configure the settings as needed.
Chapter 3 21 Specifying a Network Type to Access By default, your wireless station will attempt to connect to an Infrastructure network (if available) first. If an Infrastructure network is not available, an Ad Hoc network will then be attempted. However, it is possible that you want connect to certain networks only. In this situation, you can specify the network to access by clicking the Advanced button on the Wireless Networks tab. Then select your preferred access type and click OK. For example, you want to connect to an Ad Hoc network but both Ad Hoc and Infrastructure networks are available. In this case, you can select the Computer-to-computer (ad hoc) networks only option.
54Mbps 802.11g Wireless LAN Card 22 Note that if your preferred network is limited to Access Point or Ad Hoc network, the Preferred networks section on Wireless Networks tab will list only the networks of your preference. If you try to add a new network of non-preferred type, the addition will not appear in the list unless you change the preferred network types. Link Status Tab The Link Status tab contains general information about the connection and activity of your current link. The following table describes the items found on the Link Status screen. Screen Item Description Status Displays whether the card is associated with a network. Network Name (SSID) Displays the name of the wireless network your station is currently connected to. AP’s MAC Address The MAC address of the associated AP. Channel The channel your wireless station is using. WEP Displays whether WEP is disabled or enabled in the current wireless network.
Chapter 3 23 Screen Item Description Speed Displays the current packet transmit rate (Mbps). Channel Displays the channel the station is using. Client IP Address Displays the IP address of your wireless adapter. Network Connection Type Displays if the adapter is connected to an Access Point or Ad Hoc network. Radio State Displays whether the RF Signal is enabled or disabled. Signal Displays the signal strength (dBm). On the right side, signal strength is indicated by graphic. Noise Displays the noise level (dBm). Noise Level reflects the level of radio interference as measured at the Wireless LAN Card.
54Mbps 802.11g Wireless LAN Card 24
Chapter 3 25 Statistics The Statistics tab displays the current and accumulated statistics information pertaining to your Wireless LAN Card. The following transmit and receive statistics are provided: l Packets Sent l Packets received l Packets lost l Total packets sent l Total packets received
54Mbps 802.11g Wireless LAN Card 26 Site Monitor The Site Monitor tab displays the general information of the wireless network available in the air. You can use the Site Monitor feature to display the communications quality of your computer with multiple Access Points in its vicinity. The Site Monitor allows you to conduct a site survey to: l Determine the overall wireless coverage of your wireless network. l Optimize placement of the Access Point(s), to provide seamless connectivity to mobile stations. l Roam throughout the wireless network environment with your station, you will be able to identify areas that may not have adequate coverage, or that suffer from interference by other (wireless) equipment such as microwave ovens. The Visible Networks list will update automatically to display all visible networks. Optionally you can click Freeze to temporarily stop the update of the list. To display only the Ad Hoc network, check the Ad hoc networks only checkbox. For each network, the following information will be displayed: Field Description Network Name (SSID) Displays the name of the wireless network your station is currently connected to.
Chapter 3 27 Field Description Channel The channel your wireless station is using. Signal Strength Displays the signal strength (dBm). WEP Displays WEP whether is disabled/enabled. For a selected network, the following information will be displayed: Field Description Standard The IEEE 802.11 wireless standard. Supported Rates The supported rates of the wireless network.
54Mbps 802.11g Wireless LAN Card 28
Chapter 3 29 Advanced Site Monitor Clicking the Advanced button on the Site Monitor tab brings out the Advanced Site Monitor screen. The screen displays the following information in addition to those appear on the Site Monitor tab: Field Description AP MAC The MAC address for the wireless network interface of the Access Point. Signal Signal level indicates the strength of the wireless signal as received at the Wireless LAN Card. Both dBm value and graphic indicator are displayed. Noise (dBm) Noise Level reflects the level of radio interference as measured at the Wireless LAN Card. Both dBm value and graphic indicator are displayed. SNR (dBm) The Signal-to-Noise Ratio (SNR) is the primary diagnostic counter to diagnose wireless performance. SNR indicates the relative strength of the received Signal Level compared to the Local Noise Level. In most environments, SNR is a good indicator for the quality of the radio link between transmitter and receiver. A higher SNR value
54Mbps 802.11g Wireless LAN Card 30 Field Description means a better quality radio link. Both dBm value and graphic indicator are displayed. Supported Data Rates Displays the data rates supported by the Access Point. You can sort the list of Access Points by clicking the filed you want to use as a criteria. You can also create log files based on the monitor measurements on the Advanced Site Monitor screen. To create a log file, click the Start Log button and specify the path and filename for the log file. Then the system will automatically append log entry to the file at regular intervals until you click the Stop Log button.
Chapter 3 31
54Mbps 802.11g Wireless LAN Card 32 Diagnostics Tab To perform a diagnostics, select the test you want to perform and then click Run and then click OK if prompted. Note that by running diagnostics your network connection will be temporarily interrupted. Connection will be resume after the completion of selected tasks. After the selected tasks are completed, the test result (Passed or Failed) will be displayed. You can select desired task to see detailed test information in the Status section. The diagnostic allows to perform the following test: Test Item Description Control Registers This test verifies the read and write capabilities of the network controller registers by writing various values to the registers and verifying the result. The device driver uses these registers to perform network functions such as sending and receive information. If the test fails, the network adapter may not work properly. SPROM Format Validation This test verifies the content of the SPROM by reading a portion of the SPROM and computing the checksum. The test fails if the computed checksum is different than the checksum stored in the SPROM. Memory Tests This tests verifies that the network controller internal memory is functioning properly. The test writes patterned values to the memory and reading back the results. The test fails if an erroneous
Chapter 3 33 Test Item Description value is read back. The network controller will not function without its internal memory. Interrupt Test This tests verifies that the network controller internal memory is functioning properly. The test writes patterned values to the memory and reading back the results. The test fails if an erroneous value is read back. The network controller will not function without its internal memory. Loopback Test This test verifies that the NDIS driver is able to receive interrupts from the network controller. LED Test This test verifies that your 802.11 wireless networking hardware is functioning correctly. This test is applicable to PC Card only.
54Mbps 802.11g Wireless LAN Card 34
Chapter 3 35 Information Tab The Information tab displays the basic information about the device, including the hardware and software details.
37 Chapter 4 Windows XP Wireless Zero Configuration Utility Windows XP provides built-in Wireless Zero Configuration utility for wireless configuration and monitoring. You can choose to configure your wireless network via either the Wireless Client Manager as described in preceding section, or to use the Windows XP Wireless Zero Configuration utility. This section only provides the essential instructions on using Windows XP wireless utility to get your wireless network established. For more information please refer to Windows XP on-line help. Connecting to an Access Point or Wireless LAN Card To connect to an existing Access Point/Wireless LAN Card, take out the following steps: 1. Right-click the Wireless Connection icon on the system tray and select View Available Wireless Networks from the context menu.
54Mbps 802.11g Wireless LAN Card 38 Note: Depending on whether your wireless network is established, the context menu may come with different items. 2. When the Connect to Wireless Network window pops up, you will see all the Access Points or Wireless LAN Cards that are available in the air. Select the wireless network you want to connect to . Figure 3-4 Windows XP Configuration Utility-Connect to Wireless Network 3. If the target Access Point/Wireless LAN Card has been set with WEP key, you must enter the same WEP key in the Network key field. Otherwise, leave it blank.
Chapter 4 Windows XP Wireless Zero Configuration Utility 39 4. Click Connect, then you will join the target network and this dialog window will disappear. When your wireless connection is established, the connection icon appears as below: Note: If the wireless connection can’t be established, double-click the connection icon and then click Properties. Go to Authentication tab first to make sure that you use the correct authentication type for the Wireless LAN Card. For mo re information, refer to “Authentication” on page 45. Viewing Wireless Connection Status After you successfully connect to the Access Point or Wireless LAN Card, double-click the icon in the system tray again. This will open the Wireless Network Connection Status window where you can see the general data of the Wireless LAN Card, such as Status, Duration, Speed, Signal Strength, etc.
54Mbps 802.11g Wireless LAN Card 40 Figure 3-5 Windows XP- Connection Status Configuring Your Wireless Properties To configure your wireless properties, open the Wireless Network Connection Status window as described above, and then click the Properties button. This will open the Wireless Network Connection Properties window which allows you to configure more detailed items of the Wireless LAN Card. The following describes each tab of the properties window to help you do more settings of the Wireless LAN Card.
Chapter 4 Windows XP Wireless Zero Configuration Utility 41 General This tab allows you to specify the network methods to be used with your Wireless LAN Card. The network policy depends on your wireless network. For TCP/IP protocol, you should configure its properties as instructed by your network administrator. For more information on TCP/IP setting, please refer to “Appendix C Setting Up TCP/IP” on page 57. Figure 3-6 Windows XP Connection Properties -General
54Mbps 802.11g Wireless LAN Card 42 Wireless Networks This tab contains two sections: Available networks and Preferred networks described as below. Under Available networks section, you can also see all the Access Points and Wireless LAN Cards available in the air. Clicking Refresh will update the list of Access Points and Wireless LAN Cards. Figure 3-7 Windows XP Connection Properties-Wireless Networks
Chapter 4 Windows XP Wireless Zero Configuration Utility 43 Under Preferred networks section, you can add any wireless networks that you wish to connect to. To do this, just click Add to add more Access Points or Wireless LAN Cards to the list. After you click the Add button, the Wireless Network Properties window pops up. Type your network name (SSID) and, if needed, the wireless network WEP settings. Once the Access Point or Wireless LAN Card that you want to connect to has been set with WEP key, you must type the same WEP key as the Access Point’s or Wireless LAN Card’s. Figure 3-8 Windows XP-Add Preferred Networks
54Mbps 802.11g Wireless LAN Card 44 After you add several profiles into Preferred networks, you can change the order in which connection attempts to preferred networks are made. Just select the target wireless network and click Move up or Move down to move it to a desired position. To Access Certain Wireless Network Only If you just want to access certain wireless network type, click the Advanced button on the Wireless Networks tab (Figure 3-12) to open the Advanced window. You can choose to connect to the following networks: • Any available network ( access point preferred) • Access point (infrastructure) • Computer-to-computer (Peer-to-Peer Group) The default network type is Any available network ( access point preferred). In this network type, your device will connect to any Access Points or Wireless LAN Cards available in the air but Access Point always demands higher connection attempt priority. Once you finish the advanced setting, your wireless station will then connect to your desired network and the connected network will be listed under Available networks.
Chapter 4 Windows XP Wireless Zero Configuration Utility 45 Figure 3-9 Windows XP Configuration Utility-Set up Network to Aceess Authentication This tab allows you to configure the authentication settings of your Wireless LAN Card. The most important setting for the Wireless LAN Card is to disable Enable network access control using IEEE802.1X to ensure successful connection between the Wireless LAN Cards and Access Points or other Wireless LAN Cards. You must disable this function for any reason. Otherwise, there may be some problems happening during connection. For other settings, we recommend you keep the default settings to minimize the problems during connection.
54Mbps 802.11g Wireless LAN Card 46 Figure 3-10 Windows XP Connection Properties -Authentication Make sure to clear the Enable network access control using IEEE802.1X check box to ensure successful connection.
47 Chapter 7 Troubleshooting Radio Interference You may be able to eliminate any interference by trying the following: • Reseat the Wireless LAN Card. • Increase the distance between the wireless computers and the device causing the radio interference. • Plug the computer equipped with the Wireless LAN Card into an outlet on a different branch circuit from that used by the affecting device. • Consult the dealer or an experienced radio technician for help. • Keep the computer with the Wireless LAN Card away from the microwave oven and large metal objects.
54Mbps 802.11g Wireless LAN Card 48 Card Not Detected If the Wireless LAN Card is not detected by Windows, try the following: • Make sure the Wireless LAN Card is properly inserted in the computer. • For PC Card, make sure the slot in your computer is working. • Contact your dealer for additional testing if there is a hardware problem with the Wireless LAN Card. Cannot Connect to Another Wireless LAN Card If you cannot make a connection to another Wireless LAN Card from your computer, it could be due to one of the following reasons: • Incorrect SSID. Make sure the SSID is the same for all computers that have a Wireless LAN Card. • Changes are not being recognized by your computer. Restart your computer. • If in Ad-Hoc mode, make sure the Log on to Windows NT domain check box is not selected in the Client for Microsoft Networks Properties dialog box in the Network Configuration tab. • Incorrect IP Address or Subnet Mask. Check these settings in the TCP/IP Properties dialog box in the Network Configuration tab.
Chapter 7 Troubleshooting 49 Poor Link Quality If the Link Quality display stays in the Poor range, it could be due to one of the following reasons: • Radio interference. • Distance between Wireless LAN Card and Access Point is too far. Decrease the distance between the Wireless LAN Card and Access Point (or another card). Cannot Connect to Access Point If you cannot make a connection to the Access Point, it could be due to one of the following reasons: • Make sure the Wireless LAN Card and Access Point have no physical connection problems. • Make sure the SSID for the Wireless LAN Card is the same as the Access Point. • Make sure the privacy type is the same as that of Access Point. Also, make sure the Default Key is the same for both computers.
54Mbps 802.11g Wireless LAN Card 50
51 Appendix A Limited Warranty Wireless LAN Hardware The seller warrants to the end user (“Customer”) that this hardware product will be free from defects in workmanship and materials, under normal use and service, for 1 year from the date of purchase from the seller or its authorized reseller. The seller’s sole obligation under this express warranty shall be, at the seller’s option and expense, to repair the defective product or part, deliver to Customer an equivalent product or part to replace the defective item, or if neither of the two foregoing options is reasonably available, The seller may, in its sole discretion, refund to the Customer the purchase price paid for the defective product. All products that are replaced will become the property of the seller. Replacement products may be new or reconditioned.
54Mbps 802.11g Wireless LAN Card 52 Wireless LAN Software The seller warrants to Customer that each software program licensed from it , except as noted below, will perform in substantial conformance to its program specifications, for a period of 1 year from the date of purchase from the seller or its authorized reseller. The seller warrants the media containing software against failure during the warranty period. No updates are provided. The seller’s sole obligation under this express warranty shall be, at the seller’s option and expense, to refund the purchase price paid by Customer for any defective software product, or to replace any defective media with software which substantially conforms to applicable seller published specifications. Customer assumes responsibility for the selection of the appropriate application programs and associated reference materials. The seller makes no warranty or representation that its software products will meet Customer’s requirements or work in combination with any hardware or software applications products provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. For any third party products listed in the seller software product documentation or specifications as being compatible, the seller will make reasonable efforts to provide compatibility, except where the non-compatibility is caused by a defect in the third party’s product or from use of the software product not in accordance with the seller’s published specifications or user manual.
Appendix B Regulatory ComplianceFCC Part 15 Declaration of Conformity (DoC)The following equipment:Product Name: Wireless LAN Cardis herewith confirmed to comply with the requirements of FCC Part 15 rules. The operation is subject to thefollowing two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesiredoperation.
FCC Rules and Regulations - Part 15Warning: This device has been tested and found to comply with the limits for a Class B digital device pursuantto Part 15 of the Federal Communications Commissions Rules and Regulation. These limits are designed toprovide reasonable protection against harmful interference when the equipment is operated in a commercialenvironment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instruction manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try and correct the interference by one or more of the followingmeasures:• Relocate your WLAN equipped laptop computer.• Increase the separation between the WLAN equipped laptop computer and other electronics.• Connect the WLAN equipped laptop computer into an outlet on a circuit different from that of otherelectronics.• Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.The RF transmission power from the antenna conforms to the general public FCC limit of SAR (SpecificAbsorption Rate) 1.6 W/kg. The maximum SAR value measured from this device was 1.05 W/kg.This device must not be co-located or operating in conjunction with any other antenna or transmitter Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and awayfrom windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors issubject to licensing."
WARRANTYUsers are not authorised to modify this product. Any modifications invalidate the Warranty.This equipment may not be modified, altered or changed in any way without signed written permissionfrom Fujitsu. Unauthorised modification will void the equipment authorisation from the FCC andIndustry Canada and the warranty.
54Mbps 802.11g Wireless LAN Card 56
57 Appendix C Setting Up TCP/IP This section contains instructions for configuring the TCP/IP protocol of the Wireless LAN Card. The IP address policy depends on your wireless network. You should configure your TCP/IP protocol as instructed by your network administrator. For Windows 98/ME 1. Double-click the Network icon on the Control Panel. 2. Click the Configuration tab of the Network dialog box. 3. In the network components list, select the TCP/IP protocol of your Wireless LAN Card, e.g., TCP/IP ->Broadcom 802.11g Network Adapter and then click Properties.
54Mbps 802.11g Wireless LAN Card 58 4. On the IP Address tab, choose one of the methods as required: Option A: Click Specify an IP address. In the IP Address box, enter a valid four-component IP address, either a public or private one as required. In the Subnet Mask box, enter a valid four-component IP address. Then select the Gateway tab and enter your gateway information. Option B: Select Obtain an IP address automatically. Then an IP address will be automatically assigned to your computer. 5. Click OK to return to Network dialog box and click OK again to finish configuration. If your TCP/IP properties have been modified, you will be prompted to restart your computer. Click Yes to have new settings take effect.
Appendix C Setting Up TCP/IP 59 For Windows 2000/XP 1. Double-click Network Dial-up Connections (Windows 2000) or Network Connections (Windows XP) on Control Panel. 2. Right-click the Local Area Connection icon corresponding to your wireless adapter (e.g., Broadcom 802.11g Network Adapter) and click Properties.
54Mbps 802.11g Wireless LAN Card 60 3. On the General tab, highlight Internet Protocol (TCP/IP) and then click Properties. Option A: Use fixed IP address. Enable the Use the following IP Address option. Enter the IP address, Subnet Mask and Default gateway. Then click OK. Option B: Use dynamic IP address Select Obtain an IP address automatically. 4. Close the Local Area Connection Properties window. For Windows 2000, if prompted, click Yes to restart your computer.
Appendix C Setting Up TCP/IP 61
63 Appendix D Specifications Host Interfaces Mini PCI Form factor Type III B Chipset Broadcom BCM 4306 & BCM 2050 Operation Voltage 3.3VDC Network Standards IEEE 802.11b (Wi-Fi™) standard and IEEE 802.11g draft standard (54G) Modulation Techniques DBPSK,DQPSK,CCK,16QAM,64QAM Modulation Technology OFDM,DSSS Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Network Architectures Infrastructure and Ad Hoc Operating Frequencies 2.4-2.497 GHz Operating Channels 802.11b: 11 for North America, 14 for Japan, 13 for Europe (ETSI) 802.11g: 13 for North America, 13 for Europe (ETSI), 13 for Japan RF Output Power 15 dBm maximum output power (14 dBm nominal ± 1 dBm over operating temperature Receiver sensitivity (PER <10%) -80dBm @ 6Mbps Antenna Type Hardware diversity support: transmit and receive on Main and Auxiliary antenna connectors.
54Mbps 802.11g Wireless LAN Card 64 connectors. Range 802.11b: 11 Mbps up to 180m LOS, 60m indoors; 1 Mbps up to 570m LOS, 125m indoors 802.11g: 54 Mbps up to 50m LOS, 20m indoors; 18 Mbps up to 150m LOS, 75m indoors Power Consumption Tx peak: 550 ma @ 3.3VDC; Rx peak: 350 ma @ 3.3VDC; Idle: 225mA @ 3.3VDC Security Hardware 64/128-bit WEP engine; WEP weak-key avoidance, TKIP, hardware AES engine supporting CCM and OCB, 802.1x, SSN Delay Tolerance 802.11b: Multipath R.M.S Delay Spread @ 1% FER: 11 Mbps > 250 nsec; 5.5 Mbps > 300 nsec Client Utility Automatic location profile, site monitor, current link status, and diagnostics Software Support Microsoft WHQL certified for Windows XP, 2000, and ME. Linux and VxWorks embedded drivers. LED Indicators WLAN Activity Monitor, WLAN Radio Status Indicators Switch Manual radio on/off disables transmit and receive to comply with aviation in-flight restrictions Temperatures Operates from 0 to 70 ? Storage from -40 to 90 ? Humidity (non-condensing) 5 to 95% Certifications Wi-Fi; FCC part 15C/15.247; ETS 300 328-2; UL; IEC60950; EN 301 489-1,17; prEN50371 ;CE Mark; TELEC
65 Glossary 10BaseT An IEEE standard (802.3) for operating 10 Mbps Ethernet networks (LANs) with twisted pair cabling and a wiring hub. Access Point An internetworking device that seamlessly connects wired and wireless networks. Access Points combined with a distributed system support the creation of multiple radio cells that enable roaming throughout a facility. Ad-Hoc A network composed solely of stations within mutual communication range of each other (no Access Point connected). BSS Basic Service Set. A set of stations controlled by a single coordination function. Channel A medium used to pass protocol data units that can be used simultaneously in the same volume of space by other channels of the same physical layer, with an acceptably low frame error ratio due to mutual interference. Encapsulated An Ethernet address mode that treats the entire Ethernet packet as a whole and places it inside an 802.11 frame along with a new header.
54Mbps 802.11g Wireless LAN Card 66 ESS Extended Service Set. A set of one or more interconnected Basic Service Sets (BSSs) and integrated Local Area Networks (LANs) can be configured as an Extended Service Set. Ethernet The most widely used medium access method, which is defined by the IEEE 802.3 standard. Ethernet is normally a shared media LAN; i.e., all the devices on the network segment share total bandwidth. Ethernet networks operate at 10Mbps using CSMA/CD to run over 10BaseT cables. Gateway A network component that acts as an entrance to another network. IEEE 802.11 The IEEE 802.xx is a set of specifications for LANs from the Institute of Electrical and Electronic Engineers (IEEE). Most wired networks conform to 802.3, the specification for CSMA/CD-based Ethernet networks or 802.5, the specification for token ring networks. 802.11 defines the standard for wireless LANs encompassing three incompatible (non-interoperable) technologies: Frequency Hopping Spread Spectrum (FHSS), Direct Sequence Spread Spectrum (DSSS), and Infrared. IEEE standards ensure interoperability between systems of the same type. Infrastructure A wireless network centered about an Access Point. In this environment, the Access Point not only provides communication with the wired network but also mediates wireless network traffic in the immediate neighborhood. IP Internet Protocol. The standard protocol within TCP/IP that defines the basic unit of information passed across an Internet connection by breaking down data messages into packets, routing and transporting the packets over network connections, then reassembling the packets at their destination. IP corresponds to the network layer in the ISO/OSI model.
Glossary 67 IP Address An IP address is a 32-bit number that identifies each sender or receiver of information sent across the Internet. An IP address has two parts: the identifier of a particular network on the Internet and an identifier of the particular device (which can be a server or a workstation) within that network. ISP Internet Service Provider. An organization that provides access to the Internet. Small ISPs provide service via modem and ISDN while the larger ones also offer private line hookups (T1, fractional T1, etc.). LAN Local Area Network. A communications network that serves users within a defined geographical area. The benefits include the sharing of Internet access, files, and equipment, such as printers and storage devices. Special network cabling (10BaseT) is often used to connect the PCs together. NAT Network Address Translation. The translation of an Internet Protocol address (IP address) used within one network to a different IP address known within another network. One network is designated the internal network and the other is the external. The internal network then appears as one entity to the outside world.
54Mbps 802.11g Wireless LAN Card 68 Radio Frequency RF, Terms: GHz, MHz, Hz —The international unit for measuring frequency is Hertz (Hz), equivalent to the older unit of cycles per second. One megahertz (MHz) is one Million-Hertz. One giga hertz (GHz) is one Billion-Hertz. The standard U.S. electrical power frequency is 60 Hz, the AM broadcast radio frequency band is 0.55–1.6 MHz, the FM broadcast radio frequency band is 88–108 MHz, and wireless 802.11 LANs operate at 2.4GHz. SSID Service Set ID. A group name shared by every member of a wireless network. Only client PCs with the same SSID are allowed to establish a connection. Subnet Mask A value that defines whether your computer communicates only within your LAN or communicates outside of your LAN, where it is routed out to the rest of the Internet. A Subnet Mask that has the same first three components (for example, 255.255.255.0) is the routing pattern for a Class C address. TCP Transmission Control Protocol. The standard transport level protocol that provides the full duplex, stream service on which many applications’ protocols depend. TCP allows a process on one machine to send a stream of data to a process on another. Software implementing TCP usually resides in the operating system and uses the IP to transmit information across the network. WEP Wired Equivalent Privacy. The optional cryptographic confidentiality algorithm specified by 802.11. The algorithm is being used to provide data confidentiality that is subjectively equivalent to the confidentiality of a wired LA N medium that does not employ cryptographic techniques to enhance privacy..

Navigation menu