Fulcrum ML22 WIRELESS REMOTE CONTROL LED FastTrack Light User Manual WRCFastTrack InstructionsV2 ZH
Fulcrum Products, Inc. WIRELESS REMOTE CONTROL LED FastTrack Light WRCFastTrack InstructionsV2 ZH
Fulcrum >
Users Manual
279*29OMM Wireless Remote control FastTrack Light barriers (Walls. clothing. shelvmg. etc.) and so does not require line of sight operation as is the case with Operating Instructions 0 . o \ ' mounting hucklt ' Wish to remove lullrfy saver door = . battery cover our D - . o 0/ I- ow mum; Battery Installation & Replacement 1) Open the two battery cover doors and remove them 2) install 3 AA batteries in each compartment. matting certain to match the polarity as shown on the diagram in the battery compartment 3) Do not mix battery types Use only fresh batteries Alkaline are recommended. 4) Check light operation to confirm that batteries are correctly installed 5) Replace the battery covers Operating the Light You can operate the FastTrack Light one of two ways: manually or by using a Wireless remote control sWitch, purchased separately " Manual Operation 1) Press the power button once to turn the light on. 2) Press again to turn it oft 3) To the dim the light, press and hold the power button until the desired light level is reached and release RC System Compatible Use any combination of up to 20 RC Compatible lights or sWitches to solve your lighting problems. Remote Control Switch Operation’ 1) Press the on symbol I once to turn the lights on. 2) Press the off symbol It once to turn the lights off 3) To dim the lights. press and hold the on symbol I until the desired light level is reached. then release Group Code/ DIP Switches Each light and sWitch comes with 3 DIP sWitches that enable the user to operate 2 or more groups of lights Without interfering With each other These switches come preset from the factory and will not require adiustment unless: 1) You are adding lights to the group. or 2) You are operating 2 or more groups of lights Within 60' of each other The switch pasrtrarrs on the fig/tr should match the sWitch positions on the Adding Lights to Vour Group switoli 1) Remove the battery cover. 2) Use a pointed obiect to gently move the DlP sWitches to match the settings on the switch. Eh Ii! “3 ”ti . 3) Check operation by pressing the sWitch on and off. It) Replace the battery cover. 5) Repeat the process With all of the remaining lights in the group Adding Lights 8: Switches 1) Simply follow the instructions above and arrange the 3 DlP sWitches to match the code of the group to which you are adding lights 2) We do not recommend groups in excess of 20 lights and sWitches (total combined) 5 r r mllmhmlri In".- Installing additional Lights The chiet benefit of using 433Mhz radio frequency control is that it works through most common 'Assnciated Model Relerence - ll 3W1 9-303 Wireless Remote Control LED Lighting System infrared systems.Therefore you can choose a sWitch location that is most convenient for you to operate the system You can locate the lights where they are needed most Without concern for the barriers that might exist This proVides the user With enormous flexibility Lights can be located in different rooms, different closets. or even on different floors of the house it desired We recommend choosmg the desved location for the lights and testing the operation of the system before commencing the actual installation Locate the lights where they are most needed Without regard for physical barriers and test by turning them on and off several times. You may occasionally experience a slight delay in one or more lights This is normal Although We have made every effort to synchronize the operation at these fights, external conditions may cause a slight delay and on rare occasions the lights may not turn on or off If this happens, simplytuin the lights otf and then on again lf it happens repeatedly, there maybe external factors that are disrupting the signal and the location of the light may need to be altered. Once the final location of the lights has been determined. please remove the battery cover and follow steps below to mount the light. Please note: For optimal performance we recommend installing the lights f2“ or more apart from each other Mounting Instructions Determine the location of the lights and sWitch. as noted above. then remove the mounting plate from the sWitch and the battery cover/mounting plate from the light and follow the steps below to mount them Double-sided Tape Mounting: Be certain that surface ot the mounting location is clean and dry. Peel off the protective film and attach the tape to the mounting plate Peel otl the remaining file and press the mounting plate firmly on to the mounting surface. Be aware that the tape may damage painted surfaces when it is removed Screw Mounting , Wood Surfaces: Mount the bracket using two screws Drill a T/fE“ pilot hole. insert the screw and gently tighten it until the mounting plate is secure. Do not over tighten. Screw Mounting — Drywall: Mount the bracket using two screws and anchors Drill S/ffi“ pilot holes. insert drywall anchors and press firmly until they are fully seated into the wall Insert the screws and gently tighten until the mounting plate is secure. Do not over tighten the screws FCC Statement This device complies With Part 15 of the FCC Rules Operation is suoiect to the toiiowing two conditions (1) This device may not cause harmful interference. and (2) this device must accept any interference received. including interlerence that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital dewce. pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and, if not installed and used in accordance With the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference Will not occur in a particular installation lf this equipment does cause harmful interlerence to radio or television reception, Which can be determined by turning the equipment oft and on, the user is encouraged to try to correct the interference by one or more of the foffoWing measures 0 Reorient or relocate the radio or TV antenna - lncrease the separation between the lights and the radio or TV - Consult the dealer or an experienced radio/TV technician for help Limited 2 Year Warranty This product is guaranteed against detect and workmanship tor a period of 2 years trom the date of purchase ft the product fails during normal use. please return it to the place of purchase togetherWith a copy of the sales receipt Alternatively, you may contact us at info@fulcrumproducts com and we Will arrange to have the product replaced or repaired at our discretion. WARMING Modifications to this or other products by anyone other than an authorized repair agent may void that product‘s warranty Specifications , Model it 30037-308 Operating Mode: 433MHz radio frequency control Operating Distance 60‘ LED Type ’ix sMp Lumens 85 fumens Color Temp 4000 Kefvm (warm White) Battery Type M (x6), alkafire recommended Battery Life approx 55760 hou's Battery Standby Life approx f2 monthsactuaf battery f'fewrff vary according to frequency of use Included Items Screws a drywall anchors - Operating instructions CAUTION Do not mix battery types Use only fresh batteries for reliable operation Do not look directly intothc light FULCRUIL lnrrovatiorr nv Dcsierr Fulcrum Products, Inc.- inlo@lulerumproducts.com - 503-274-1227
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Format : application/pdf Title : WRCFastTrack InstructionsV2-ZH Metadata Date : 2016:06:17 09:42:29+08:00 Modify Date : 2016:06:17 09:42:29+08:00 Create Date : 2016:06:17 09:42:28+08:00 Creator Tool : Adobe Illustrator CS6 (Windows) Thumbnail Width : 236 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 26941 bytes, use -b option to extract) Instance ID : uuid:97fba81e-d6a7-4349-bd16-04d9358a031b Document ID : xmp.did:1944741C2A34E611B3E0EABBB71545EC Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:1844741C2A34E611B3E0EABBB71545EC Derived From Document ID : xmp.did:1844741C2A34E611B3E0EABBB71545EC Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:1744741C2A34E611B3E0EABBB71545EC, xmp.iid:1944741C2A34E611B3E0EABBB71545EC History When : 2016:06:17 09:38:53+08:00, 2016:06:17 09:42:25+08:00 History Software Agent : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows) History Changed : /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 304.474438 Max Page Size H : 309.076053 Max Page Size Unit : Millimeters Font Name : AdobeSongStd-Light Font Family : Adobe 宋体 Std Font Face : L Font Type : Open Type Font Version : Version 5.002;PS 5.002;hotconv 1.0.49;makeotf.lib2.0.15106 Font Composite : False Font File Name : AdobeSongStd-Light.otf Plate Names : Black Swatch Groups Group Name : 明亮 Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 60.000002 Swatch Groups Colorants Magenta : 90.000004 Swatch Groups Colorants Yellow : 0.003099 Swatch Groups Colorants Black : 0.003099 Producer : Adobe PDF library 10.01 Page Count : 1 Creator : Adobe Illustrator(R) 16.0 For : Administrator, Bounding Box : -60 -829 733 40 Container Version : 11 Creator Version : 16EXIF Metadata provided by EXIF.tools