Global Sun Technology GL242201-MT Wireless 22Mbps PC card User Manual manual

Global Sun Technology Inc Wireless 22Mbps PC card manual

Manual

1CONTENTS1. PRODUCT GENERAL INFORMATION..……………………………………………..….21.1. Product Description…………………………………………………………………………………….21.2. Product Feature…………………………………………...……………………………………………21.3. Product Application………………………………………………………….……………………………..22. PRODUCT GENERAL………………………………………………………………….….32.1. General Specifications………………………….………………..…………………………..… 32.2. LED Indicator………………………………………………………..…………..….………………32.3. Interface………………………………………………………….…….………………………..…..33. PRODUCT HARDWARE SPECIFICATION……………………….………………….….33.1. RF Specification…………………………………………………….………….….…………………..….33.1.1. General……………………………………………………….………………..………………..33.1.2. Transmitter…………………………………………………….…………..……………………33.1.3. Receiver…………………………………………………………………..……………………43.1.4. Antenna Type………………………………………………….…………..…………………...43.1.5. Typical Operating Range………………………………………….………..…………………43.2. H/W Specification………………………………………………………….…………………………....43.2.1. MAC Controller.…………………………………………………….……..……………………43.2.2. Memory.……………………………………………………………….…..…………………….43.2.3. Power……………………………………………………………………....……………………44. PRODUCT SOFTWARE SPECIFICATION………………………………….……...……44.1. Driver…………………………….……………………………...……………..……………………..…..44.2. Configuration Utility………………..…………………………….………..………………………..….45. PRODUCT COMPLIANCE………………………………………………………….……..56. OPERATING CONDITION……………………………………………………..……..56.1. Drop and Vibration test……………………………….……………………………...……….56.1.1. Anti-Static Voltage……………………………………………………………………..………..56.1.2. Vibration Test………………………………………………………..…………….….………..56.1.3. Package Drop Test……………………………………………………………….…..…………56.2. Operation Environment ……………………………………………………………………...……….…56.2.1. Temperature Range………………………………………………………………….…………5 6.2.2. Reliability Test…………………………………………………….…………….56.2.3. Humidity…….…………………………………………..…………………………………….….57. INSTALLATION AND CONFIGURATION……………………..………………..……..67.1. Installation………….……………………………….……………………………...……….67.2. Configuration……………………………………………………………………………...……….…6
2WLAN PC Card1. Product General Information1.1. Product DescriptionGL242201, the wireless Ethernet adapter for Card bus- compliantnotebook PCs, is fully compatible with IEEE 802.11b standardand supporting higher data rate to 22Mbps. Using DirectSequence spread spectrum technology for immunity frominterference, it will automatically fallback to lower data rate in theenvironment of interference.22Mbps data rate is designed by the Packet Binary Convolution Code (PBCC) modulation technique. The softwaresupports Windows OS such as Win98, Win2000, WinME and WinXP. The PC card for your laptop is designed with anintegrated diversity antenna which would increase the receiving and transmitting sensitivity.1.2. Product Feature● IEEE 802.11b Direct Sequence high rate compatible.● Based on DSSS Technology and support the modulation of PBCC mode● High-Speed wireless connection up to 22Mbps data rate, and supports 11/5.5/2/1 Mbps 802.11b standard● Advanced Power Management supports power saving mode for battery device● Auto fallback data rate in the environment of interference● 64/128/256 Bits WEP Encryption function● High through-put supports multi-media data bandwidth requirement● Built-in PCB patch diversity antenna or external antenna support.● Supports Card Bus interface1.3. Product Application● Wireless Networking in Enterprise, SOHO and Home environment● Wireless Networking Access in Hot Spot area such as Airport, Hotel, School, Convention center, Coffee shop, …etc.● Mobile media through wireless LAN● Mobile networking for notebook PC, and Mobile devices● Wireless access to devices such as Printer, Scanner, WebCAM, … etc.● Build system in Ad-Hoc for Host-Client appliance or Infrastructure mode for multi-access
3 2. PRODUCT GENERAL2.1. General SpecificationsStandards: IEEE802.11b CompliantPC Card standard Ver 7.0Data Rate: 22Mbps / 11Mbps / 5.5 Mbps / 2Mbps / 1 Mbps auto fallbackSecurity: 64/128/256 bit Wired Equivalent Privacy (WEP)Dimension: 128 x 54 x 5.0 mm (Non-detachable card)2.2. LED IndicatorsPower/Status Unlighted: Power OffRed color LED steady On: Power onRF TX/RX Unlighted: no activityGreen color LED blinking: TX/RX activity2.3. InterfaceCARD BUS PC Card standard Ver 7.03. PRODUCT HARDWARE SPECIFICATIONS3.1. RF Specification3.1.1 GeneralEmission Type Direct Sequence Spread Spectrum (DSSS)RF Frequency 2400MHz – 2497 MHz – Japan Band2400MHz – 2472MHz – North America 2400MHz – 2483.5MHz – Europe2446.5MHz – 2483.5MHz – FranceOperating Channel 11 Channels (US, Canada)13 Channels (Europe)14 Channels (Japan)Radio Chipset: MaximMedia Access Protocol CSMA/CA (Collision Avoidance) with ACK3.1.2 TransmitterRF Output Power 13.6 dBmFrequency Stability Within + 25 ppmData modulation type BPSK / QPSK / CCK / PBCCData modulation speed 22/11/5.5/2/1 Mbps with auto fallback
43.1.3 ReceiverSensitivity -80 dBm (Typically @25+5)3.1.4 Antenna TypeAntenna Type Built in diversity patch antennaAntenna Gain 2 dBi max.3.1.5. Typical Operation Range 22Mbps 100M11Mbps 150M5.5Mbps 250M2Mbps 300M1Mbps 350M3.2 Hardware Specification3.2.1 MAC controllerTI ACX1003.2.2 Memory8Kbit EEPROM3.2.3 PowerPower Voltage 3.3 or 5 Volt + 5%Power Consumption 650 mA by TX (Max)350mA by RX4. PRODUCT SOFTWARE SPECIFICATION4.1. DriverNDIS4.0 LAN driver for Win98 NDIS5.0 LAN driver for Win2000, Win ME NDIS5.1 LAN driver for Win XP4.2. Configuration UtilityConfiguration Utility software program for Win98, Win2000, WinME and WinXP.Configurable Parameters DescriptionNetworking Type Infrastructure / Ad-HocChannel Channel number setting (14 channels available)ESSID ESSID settingRx Rate Current Receiving data rateTX Rate Current Transmitting rateWEP Disable, 64 bit, 128 bit and 256 bit
5Link Quality Receiving AP link quality on infrastructure networking modeSignal Strength Receiving AP signal strength on infrastructure networking mode5. REGULATION COMPLIANCECompliant withFCC Part 15 Class B and CETSI EN 300 328-2 and ETSI EN 301 489-1, -17, EN60950, CE-MarkTelec (Japan, Customized)WiFi Compliant6. Environmental Requirement6.1. Drop and Vibration6.1.1. Anti-Static VoltageStatic voltage tests by 4 kV in card frame should not cause system fail 6.1.2. Vibration TestThe vibration test is under the frequency and amplitude 10-25 Hz 1mm in vertical and horizontal direction by 30minutes that should not cause any damage on product.6.1.3. Package Drop TestDropping the package from the height of 50cm for each of the six(6) faces onto the hard-wood floor should not causeany damage on product.6.2. Operation Environment6.2.1. Temperature RangeOperating: -0 - +55 (Except RF output power and sensitivity)Storage: -20 - +706.2.2. Reliability TestOne cycle of reliability test is keeping at -30 by 2 hours, switching temperature up to +60 within one hour , andtesting at +60 by 2 hours, and switching temperature to -30 within one hour. Three cycle should be tested andwithout any product fail.6.2.3. HumidityOperating: 0% to 70%
6Storage 0% to 95% Non-condensing7. INSTALLATION AND CONFIGURATION7.1. Installation1. Start the computer2. Insert the PC CARD to the slot of computer3. Run ”E:\ Wlan PC Card\Utility\Setup.exe”. Windows will automatically start Installshield Wizard and then insert the PCCARD into the slot of the computer.4. Select “PC Card/PCI Card”5. Click “Install “ Button.6. Click “Next” button.7. Click “Finish” button to restart computer.7.2. Configuration1. Please insert your Wireless Card into PCMCIA slot.2. Click “ ” icon in the right hand corner of the screen.3. The Utility configuration link information page should appear on your monitor. It will show you the Wireless card status.
7 4.Click the “Configuration”. The Configuration page will appear. Enter your wireless network’s SSID, select the BSS Type,suggest you use default “Infrastructure”, Then click “Apply”.5. Click the “Security”. From the security setting screen, you can set the WiredEquivalent Privacy (WEP) encryption by checking the “Data Encryption”. Then change the“Key Format” to “ASC II”. It is easier than using the “HEX” format. Enter a set ofrandom combination of number and alphabet in the “Network Key” frame. Then click“Apply”. Follow the appearing dialogue to adjust the length of the entering “Network Key”based on the “Key Length”. Then click “Apply” until no dialogue appears.
8If you have an access point and enable the security function, please follow the access point“Network Key”.6.Click “SiteSurvey”. Select one of SSID from “Available Network” Block. Then click “Connect” button to enter Profilepage.7. You can set all parameters or click “OK” to back to previous page. If you click “OK” directly, then you finish the connectaction.
98.Click “About”. It will show you Software Version of this Wireless Lan PC Card.Notice : Our company reserves the right to change specifications detailed in this document at any timewithout notice, and assumes no responsibility for any errors within this document.
10Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if t not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by during the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:¾ Reorient or relocate the receiving antenna.¾ Increase the separation between the equipment and receiver.¾ Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.¾ Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Printed in Taiwan

Navigation menu