HON HAI PRECISION IND MICA2 WIFI 11A/N MODULE User Manual MIC A2 2011 08 10
HON HAI Precision Ind. Co., Ltd. WIFI 11A/N MODULE MIC A2 2011 08 10
Contents
- 1. User Manual
- 2. EN_manual
User Manual
MIC-A2 WIFI Module User Manual Rev. 0.01 Confidential Reviewers Review Dates Department Name Plan Results Director of Engineering Hardware Engineering Confidential Table of Contents 1. INTRODUCTION .................................................................................................................................................. 4 1.1 SCOPE .............................................................................................................................................................. 4 1.2 FUNCTION ........................................................................................................................................................ 4 2. PRODUCT SPECIFICATION ............................................................................................................................... 5 2.1 ELECTRICAL SPECIFICATION ................................................................................................................................ 5 3. MECHANICAL DRAWING .................................................................................................................................. 6 4. REGULATORY INFORMATION ........................................................................................................................ 7 Confidential 1. Introduction Project Name: 802.11n WIFI module This documentation describes the product specification of the 802.11n WIFI module, it is a confidential document of FOXCONN. 1.1 Scope The MIC-A2 802.11n WIFI module provides wireless modem functionality utilizing OFDM technology. The objective of this use manual is to verify the functionality of the MIC-A2 802.11n WIFI module RF/Digital electronic design against the design specifications. This revision includes results taken at various temperatures (0℃,25℃,65 ℃) and VDD voltages (3.1V,3.3V,5.25V), VDDIO Voltage (2.7V,2.8V,2.9V). Included are statements of test purpose, test methodologies, test modes and parameters, environmental conditions, applicable specifications, and typical reference design performance. The major specifications and documents are listed below and upon to update in the following new revisions. ● 802.11n: IEEE P802.11n/D2.07-Mar 2006 Paragraph 20.3.20.1 This device is operated in 5180~5240MHz (indoor only) and 5745~5825MHz. 1.2 Function Support IEEE 802.11n specified functions 1x1 single stream with antenna diversity SDIO V2.0 interface support Confidential 2. Product Specification 2.1 Electrical Specification Absolute Maximum Ratings These specifications indicate levels where permanent damage to the device can occur. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended can adversely affect long-term reliability of the device. Confidential 3. Mechanical Drawing Confidential 4. Regulatory Information USA-Federal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Labeling Hon Hai Precision 802.11n WIFI module MIC-A2 labeled as below. FCC ID: MCLMICA2 The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: MCLMICA2” shall be placed on the outside of final host system. Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device. Labeling Hon Hai Precision 802.11n WIFI module MIC-A2 labeled as below. IC :2878D-MICA2 The proposed with IC No. label format is to be placed on the module. If IC No. is not visible when the module is installed into the system, “Contains IC :2878D-MICA2” shall be placed on the outside of final host Confidential system. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. Caution: Exposure to Radio Frequency Radiation. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Confidential
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : 21598 Create Date : 2011:08:30 16:25:26+09:00 Modify Date : 2011:08:30 16:25:26+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.3.3 (Windows) Format : application/pdf Title : Microsoft Word - MIC-A2_User Manual_2011.08.10.doc Creator : 21598 Document ID : uuid:35f38d32-8075-462c-878b-53909a4a35eb Instance ID : uuid:ed457a7a-6850-4f97-b5b6-f2a4433b5037 Page Count : 8EXIF Metadata provided by EXIF.tools