KIDZTECH TOYS 8441115-24GTX R/C Sand X-Monster User Manual
KIDZTECH TOYS MANUFACTURING LTD R/C Sand X-Monster
User Manual
NO.: 84411 age 1:14 SCALE PRO. SYSTEM Contents -RC Vehicle (Vehicle) x 1 -RC Transmitter (Transmitter ) x 1 -Instruction Manual x 1 -6.4V Rechargeable Battery Pack x 1 -Charger x 1 -9V Battery x 1 9V 40 6.4V RC Transmitter x 1 Battery Precaution 1. The 6.4V Lithium Rechargeable Battery Pack must be charged before use by utilizing the battery charger which included 2. Do not overcharge the battery pack. Do not charge for more than 6 hours 3. Do not charge the battery pack if it shows leakage, corrosion, or has loose or exposed wires or other damage 4. Do not cover the battery pack with any sort of materials while charging 5. Do not touch the battery pack when it is hot. Wait until the battery pack cools before installing it in the Vehicle and before recharging 6. Do not dispose of the battery in fire 7. Do not dismantle the battery or charger, and do not cut the battery or charger cables 8. The battery pack will be warm after charging, and hot after use in a vehicle 9. The supply terminals are not to be short-circuited 10. Rechargeable batteries are to be removed from the toy before being charged 11. Rechargeable batteries are only to be charged by adult. Battery Installation RC Vehicle x 1 Fig. 2 Vehicle 6.4V 500mAh For Vehicle (Included) ADAPTER (Included) 12. Battery replacement must be only made by adults 13. The transformer (charger) is not a toy 14. Charge only type (500mAh Max.) rechargeable battery packs. Other types of batteries may burst causing injury to persons and damage. This power unit is intended to be correctly orientated in a vertical or floor mount position. This charger is intended to be used for charging 6.4V lithium rechargeable battery pack with capacity 500mAh Max. It cannot be used for charging non-rechargeable batteries. Regular examination of battery charger for any damage to their cord, plug, enclosure and other parts, and that, in the event of such damage, it must not be used with the charger or battery pack charge until such damage has been repaired. Note that the 9V battery is non-rechargeable and is not to be recharged. Only batteries of the same or equivalent type as recommended are to be used. It will need replacement when transmission is poor. 15. Exhausted batteries are to be removed from the product. Charging the Rechargeable Battery Pack for the Vehicle: 1. 2. 3. 4. 5. For Vehicle (Fig. 1 and Fig. 2) 1. Switch OFF the power 2. Unscrew the screw on the battery cover 3. Open the battery cover 4. Install 6.4V battery pack with correct polarities (+/-) as shown inside the battery compartment 5. Close the battery cover 6. Tighten the screw on the battery cover 1 X 9V Battery For Transmitter (Included) Connect the 6.4V lithium rechargeable battery pack to the battery charger Plug the charger into the standard AC socket The charging time for a full charge is about 3 hours When charging is completed, unplug the charger from the AC socket Disconnect the rechargeable battery pack form the battery charger For Transmitter (Fig. 3 and Fig. 4) 1. Switch OFF the power 2. Unscrew the screw on the battery cover 3. Open the battery cover 4. Install 1 new 9V battery with correct polarity (+/-) as shown inside the battery compartment 5. Close the battery cover Fig. 4 6. Tighten the screw on the battery cover Transmitter ON/OFF (At Rear) Battery Compartment Accelerator Trigger Steering Wheel 9V Battery ON/OFF 6.4V LED Battery Indicator Direction Adjustment Fig. 1 Vehicle - Battery Installation Fig. 3 Transmitter - Battery Installation How To Bind 84411 1. Turn on the Vehicle. 2. Keep pulling the trigger of the Transmitter forward then turn the Transmitter on. Do not release the trigger until the binding process completed. 3. The LED light of the Transmitter will keep flashing for the binding process, which is within 8 seconds. Do not turn off any buttons while in progress, otherwise, the process will be terminated. 4. After the wheels of the Vehicle turn left and right and the LED light of the Transmitter stops flashing, the binding process completed for playing. 5. If it cannot complete within 8 seconds, please turn off both Vehicle and Transmitter and re-start the binding process. 6. When the binding process is done, whenever switching the Vehicle and Transmitter on and off, it searches for the code that it memorized, and will only lock on to the Transmitter signal containing that code. 7. Please turn off both Vehicle and Transmitter and re-start all binding process if changing to another 2.4GHz Transmitter for playing. How To Play 3. Use the Accelerator Trigger to drive the Vehicle Forward, Stop and Backward 1. Switch ON the Vehicle and Transmitter. Vehicle 2. Use the Steering Wheel to control the Vehicle turning left or right Turn Left Stop Forward Backward Transmitter Turn Right 4. If the vehicle does not run in straight line, adjust the Direction Adjustment on the Vehicle chassis 5. Play on smooth surface to have the optimum performance 6. Remember to switch OFF the power of the Vehicle and Transmitter after playing 7. The optimum control range is up to 40m outdoor Braking Action Keep driving forward rapidly then switch to backward for the braking action. When the trigger of the Transmitter returns to the center position, push it again for the backward action. Performance Tips 1. 2. 3. 4. Do not drive on grass, dirt, sand, dusts, carpet or go through water Do not drive in windy or rainy weather Avoid direct impact the Vehicle with obstacles Switch OFF the power when not in use to prevent damage of Vehicle and Transmitter due to leakage of electrolyte from batteries 5. Remove all batteries from the Vehicle and Transmitter when not in use for long period 6. Keep fingers, hair and loose clothing away from wheels 7. The operating range can be affected by a variety of factors a) Low Voltage of batteries in Transmitter or Vehicle b) Interference from other items that emit radio frequency signals 8. Outdoor usage is recommended in order to get optimum control range 9. Recommend to play the vehicle on a clean and smooth surface 10. Clean the battery compartment to make sure it is free from dust to prevent poor contact of batteries Cautions 1. Do not attempt to disassemble the Vehicle or Transmitter 2. Make sure the batteries are installed with correct polarities (+/-) as shown inside the battery compartment 3. Remove the package and take out all accessories before giving the Vehicle and Transmitter to child to play The packaging and instruction manual contain important information. Please keep them for future reference. Warning! Choking Hazard. Not suitable for children under the age of 3 years due to small parts. We reserve the right to improve/amend specifications and colors without notice. FCC label compliance statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the userâs authority to operate the equipment. RSS-310 Compliance Statement: This device complies with Industry Canada Licence-exempt RSS-310. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Declaration of Conformity The product is in conformity with the requirement of EU Directive 1999/5/EC Environmental notes: The whole product also does not belong to household waste at the end of the product life. You can return it at collection points for the recycling of electronic and electronical instruments The symbol on the item, instruction manual, hangtag or packing is showing this clearly. Materials should be recycled according to their respective markings. Recycling of old devices or other re-use of materials contained therein represents an important contribution to environmental protection. Please ask at your local community for the correct collection point. Disposal of batteries Batteries should not be disposed of in the household waste. As the consumer you are legally obliged to return batteries containing harmful substances and all other used batteries. You can hand in your old batteries at public collection points in your area or wherever batteries are sold. You will find these chemical abbreviations along with a crossed-out refuse bin on batteries containing harmful substances: Pb=Battery contains lead Cd=Battery contains cadmium Hg=Battery contains mercury Conforms to the safety requirements of ASTM F963 KIDZTECH TOYS MANUFACTURING LTD. Room 1201,12/F, Inter-Continental Plaza, 94 Granville Road, TST East, Hong Kong. Tel: (852) 27218868 info@kidztech.net Made in China http://www.kidztech.net
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Format : application/pdf Title : KT84411 2.4G KT84411 Sand X Monster_IM_20150511_A01 Creator Tool : Adobe Illustrator CS6 (Macintosh) Create Date : 2015:05:13 16:22:23+08:00 Modify Date : 2015:05:13 16:22:23+08:00 Metadata Date : 2015:05:13 16:22:23+08:00 Thumbnail Width : 256 Thumbnail Height : 200 Thumbnail Format : JPEG Thumbnail Image : (Binary data 22200 bytes, use -b option to extract) Document ID : xmp.did:15BB39001B206811822AA868423187AC Instance ID : uuid:4953007b-2b82-664f-b4aa-89dd6afd6e84 Rendition Class : proof:pdf Original Document ID : uuid:819A97389468E2118C6ACD37CA1DCDB5 Derived From Instance ID : uuid:121cfae7-b4bc-4546-afe7-0723ec248015 Derived From Document ID : xmp.did:0780117407206811822A82C4E2CF4DB1 Derived From Original Document ID: uuid:819A97389468E2118C6ACD37CA1DCDB5 Derived From Rendition Class : default History Action : saved, saved History Instance ID : xmp.iid:21AB06EFC08AE2119828FA54C2019313, xmp.iid:15BB39001B206811822AA868423187AC History When : 2013:03:12 14:52+08:00, 2015:05:13 16:22:10+08:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CS6 (Macintosh) History Changed : /, / Manifest Link Form : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference Manifest Reference File Path : /Users/tonylam/Desktop/Yellow Job/Kidztech version/TopMaxx/KT84411 Sand X Monster_IM/Links/Sand X Monster_Grey.psd, /Users/tonylam/Desktop/Yellow Job/Kidztech version/TopMaxx/KT84411 Sand X Monster_IM/Links/2.4G-RC-01_Grey.psd, /Users/tonylam/Desktop/Yellow Job/Kidztech version/TopMaxx/KT84171 GT Racer:Porshe911 1-12_IM/Links/Sand X monster-Link-03.psd, /Users/tonylam/Desktop/Yellow Job/Kidztech version/TopMaxx/KT84411 Sand X Monster_IM/Links/Sand X Monster_Grey02.psd Startup Profile : Print N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 20.999993 Max Page Size H : 29.700013 Max Page Size Unit : Centimeters Font Name : 321impact, ArialMT, Arial-Black, ArialNarrow, ArialNarrow-Bold, Bauer, ContinuumBold, ContinuumMedium, Impact, Impacted, MyriadPro-BoldCond Font Family : 321impact, Arial, Arial Black, Arial Narrow, Arial Narrow, Bauer, Continuum Bold, Continuum Medium, Impact, Impacted, Myriad Pro Font Face : Regular, Regular, Regular, Regular, Bold, Regular, Regular, Regular, Regular, Regular, Bold Condensed Font Type : TrueType, Open Type, Open Type, Open Type, Open Type, TrueType, TrueType, TrueType, Open Type, TrueType, Open Type Font Version : Version 1.00 March 8, 2007, initial release, Version 5.06, Version 5.00.1x, Version 2.38.1x, Version 2.38.1x, 31-01-00, Macromedia Fontographer 4.1 5/6/96, Macromedia Fontographer 4.1 5/6/96, Version 5.00, Version 2.20, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28 Font Composite : False, False, False, False, False, False, False, False, False, False, False Font File Name : 321impact.ttf, Arial.ttf, Arial Black.ttf, Arial Narrow.ttf, Arial Narrow Bold.ttf, BAUERG_.TTF, CONTB.TTF, CONTM.TTF, impact.ttf, IMPACTED.TTF, MyriadPro-BoldCond.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Cyan : 60.000004 Swatch Groups Colorants Magenta : 10.000002 Swatch Groups Colorants Yellow : 5.000001 Swatch Groups Colorants Black : 0.000000 Swatch Groups Group Name : Grayscale Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: K=100 Swatch Groups Colorants Mode : GRAY Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Gray : 255 Producer : Adobe PDF library 10.01 Page Count : 2 Creator : Adobe Illustrator CS6 (Macintosh)EXIF Metadata provided by EXIF.tools