Kar Tech MCT244 2.4GHz modular transceiver User Manual User s manual
Kar-Tech, Inc. 2.4GHz modular transceiver User s manual
Kar Tech >
User manual
MCT244 2.4GHz MODULAR TRANSCEIVER OEM INSTALLATION AND OPERATION MANUAL NOTE: THIS MODULE IS LIMITED TO OEM INSTALLATION ONLY December 8, 2015 HK MCT244 TRANSCEIVER INDEX DESCRIPTION ........................................................................... 2 OPERATION .............................................................................. 2 INSTALLATION ......................................................................... 3 BEFORE APPLYING POWER! ...................................................... 4 TROUBLESHOOTING ................................................................. 4 INDUSTRY CANADA STATEMENTS ........................................... 10 MCT244 TRANSCEIVER DESCRIPTION amplifier, a modulator and a receiver The MCT244 is a direct sequence spread spectrum transceiver module designed to free use in The transceiver. via The data is microcontroller is responsible for the control of the entire The MCT244 is not designed for antenna not be used The DC regulator which generates a to constant 1.8 VDC for the digital with circuitry. The RF section runs on any other transmitter. the 3.3V supply. OPERATION MCT244 communication. MCT244 transceiver contains a applications simultaneously The MCT244 is Direct Sequence is Spread Spectrum that can use radio one transceiver module for the 2.4 16 channels, is integrated frequency synthesizer, a power where 2.405GHZ Channel 16 is 2.480 GHZ. microcontroller includes a CPU, fully of Channel GHz ISM bands. The transceiver host the serial port and to the host. serviceable parts on the MCT244 GPI/O, the to is received from antenna is sent to Kar-Tech. There are no user The connected port to the antenna and the data control products by Kar-Tech, at transmit serial processor and then to RF circuit integrated into Kar-Tech remote should microcontroller MCT244 sent through a serial port to RF The MCT244 transceiver is only and The protection circuits. the 2.4 GHz ISM band. multiple unit. and MCT244 TRANSCEIVER The receivers are matched to simultaneously with any the transmitters to use the same other channel transmitter, except signals. accordance with INSTALLATION multi transmitter product as the 1) Solder transmitter’s the MCT244 D) The operate as requirement. host’s Application Requirements: current with draw must all persons, not In User the Manual parts the modules. b. The radio should in not “Instructions To The User” section. be c. The “Industry Canada mounted at least 20cm from MCT244 modules. on the MCT244. should not remove or install radio B) Do not remove the shield antenna the Do serviceable They of 150mA. C) The be a. That there are no user Transceiver with 3.3VDC peak to include the following: MCT244 voltage, is E) Documentations: antenna. nominal FCC without an antenna. appropriate the MCT244 applications. 2) Print and attach the label A) Power in installed only in mobile host’s compatible connector. the or procedures. transceiver directly to the 3) Connect antenna Statement”. and d. Include in the manual, transmit “This device is granted MCT244 TRANSCEIVER for use in Mobile only configurations which used the antennas for transmitter in must this be installed to provide a separation distance of at least 20cm from all person and not be colocated with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures.” BEFORE POWER! APPLYING Check power and ground for proper polarity. Read the rest of this manual. parts in the MCT244 Transceiver. Contact TROUBLESHOOTING your representative KAR-TECH for instructions or servicing. There are no user serviceable further MCT244 TRANSCEIVER There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service. PARTS LIST PART NUMBER DESCRIPTION 021531A MCT244 RADIO TRANSCEIVER – WIRE ANTENNA 021532A MCT244 RADIO TRANSCEIVER – RPSMA ANTENNA There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service. The information, specifications, and illustrations in this manual are those in effect at the time of printing. We reserve the right to change specifications or design at any time without notice. TRANSCEIVER PICTORIAL 1.8900 0.0900 0.1000 1.2500 1.1687 MCT244 TRANSCEIVER Pinout Pin Function GND Not Used GND Not Used Not Used NC Pin 10 11 12 Function NC Not Used Not Used NC RXD TXD Pin 13 14 15 16 17 18 Function NC NC NC NC VIN 3.3V GND MCT244 TRANSCEIVER TRANSCEIVER Power supply ........................................................................... 3.3VDC Operating temperature - Radio....................................... -20˚C to +55˚C Storage temperature .................................................. -40˚C to +100˚C RF Frequency ............................................................... 2.405-2.48 GHz Antenna Manufacturer …………………………………………………………….. Kar-Tech, Inc. Antenna Model………………………………………………………………………………….. MCT244 Antenna Gain……………………………………………………………………………………….. 1.1dBi MCT244 TRANSCEIVER INSTRUCTION TO THE USER This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not MCT244 TRANSCEIVER be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: P4U-MCT244 when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product MCT244 TRANSCEIVER INDUSTRY CANADA STATEMENTS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à l'établissement d'une communication satisfaisante. 10 MCT244 TRANSCEIVER OEM Responsibilities to comply with FCC and Industry Canada Regulations This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. IC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Cette modulaire doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et le corps de l'utilisateur. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 4534A-MCT244” when the module is installed inside another device, the user manual of this device must contain below warning statements; 11 MCT244 TRANSCEIVER 1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. 2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Administrator Create Date : 2016:05:13 08:50:51+08:00 Modify Date : 2016:05:13 08:50:51+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : Administrator Title : Microsoft Word - User's manual - 副本.doc Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:6c30eb8c-ba1e-4d88-9433-5ccc6c8cc895 Instance ID : uuid:3d7d17cc-a49d-4453-9ef1-18bc4f53f37b Page Count : 13EXIF Metadata provided by EXIF.tools