Kar Tech MOD164 FHSS Transceiver User Manual User s manual
Kar-Tech, Inc. FHSS Transceiver User s manual
Kar Tech >
User Manual
MOD164 900MHz MODULAR TRANSCEIVER OEM INSTALLATION AND OPERATION MANUAL NOTE: THIS MODULE IS LIMITED TO OEM INSTALLATION ONLY May 27, 2014 HK MOD164 TRANSCEIVER INDEX DESCRIPTION ........................................................................... 2 OPERATION .............................................................................. 2 INSTALLATION ......................................................................... 4 BEFORE APPLYING POWER! ...................................................... 6 TROUBLESHOOTING ................................................................. 6 TRANSCEIVER PICTORIAL ........................................................ 8 SPECIFICATIONS ...................................................................... 8 INSTRUCTION TO THE USER ..................................................... 9 INDUSTRY CANADA STATEMENTS ........................................... 10 MOD164 TRANSCEIVER DESCRIPTION The MOD164 OPERATION frequency The spectrum transceiver module for the 900 transceiver module designed to MHz ISM bands. The transceiver be compatible with US (FCC Part microcontroller includes a CPU, 15.247) GPI/O, hopping is spread and Canadian (RSS- MOD164 is fully radio integrated 210) regulations for license free frequency synthesizer, a power use in the 900 MHz ISM band. amplifier, a modulator and a The MOD164 is designed for receiver unit. The mobile microcontroller serial connected the applications in accordance to Part 2.1091(b). to protection circuits. MOD164 port host is via The data is The MOD164 transceiver is only sent through a serial port to RF integrated into Kar-Tech remote processor and then to RF circuit control products by Kar-Tech, at to the antenna and the data Kar-Tech. There are no user received from antenna is sent to serviceable the serial port and to the host. parts on the MOD164 transceiver. The microcontroller is responsible for the control of the The MOD164 is not designed for entire multiple MOD164 transceiver contains a and antenna should transmit not applications be used simultaneously communication. The to DC regulator which generates a with constant 1.8 VDC for the digital any other transmitter. circuitry. The RF section runs on the 3.3V supply. MOD164 TRANSCEIVER The MOD164 hops on 50 channel frequencies that are selected in pseudo random order. An example of the order is: {48, 25, 17, 20, 41, 37, 36, 10, 15, 44, 30, 5, 8, 28, 6, 42, 33, 1, 23, 49, 16, 3, 19, 29, 21, 43, 31, 9, 18, 27, 22, 45, 13, 2, 32, 11, 14, 46, 12, 24, 4, 7, 38, 47, 35, 40, 50, 34, 39, 26} where Channel 1 is 902.5 MHZ and Channel 50 is 927.00 MHZ. The dwell time of the hopping is 350ms. Each channel is used equally on average. The receivers are matched to the transmitters to use the same hopping channel sequence and they hop synchronization channels with in the transmitter’s signals. MOD164 TRANSCEIVER INSTALLATION 1) Solder wavelength the RPSMA MOD164 compatible 2) Print and attach the label as shown below: 3) Place a label on the outside of the host enclosure in a visible area. On the label, the following: “Contains Module Transmitter FCC MOD164” ID: and Transmitter P4U- “Contains Module IC: 4534A-MOD164” 4) Connect antenna. the appropriate Either ¼ wavelength ANT-916-CW-QW-SMA connector. include or antenna Linx Technology transceiver directly to the host’s ¼ wire, MOD164 TRANSCEIVER Application Requirements: applications. See Part 2.1091 for definitions of A) Power the mobile MOD164 peak voltage, current F) Do with draw not operate MOD164 of without the an antenna. 150mA. G) Documentations: B) Do not remove the shield host’s on the MOD164. the ¼ In User the Manual include the following: C) If you use something other than fixed applications. Transceiver with 3.3VDC nominal and a. That there are no user wave serviceable parts antenna, the unit needs the modules. separate approval. They antenna D) The or antenna the should wire must all persons, not b. The and “Instructions To The User” section. transmit antenna not modules. c. The “Industry Canada simultaneously with any other should remove or install radio be mounted at least 20cm from radio in Statement”. or in d. Include in the manual, FCC “This device is granted multi transmitter product for use in Mobile only procedures. configurations transmitter, except accordance with E) The MOD164 is to which be used installed only in mobile the for in antennas this MOD164 TRANSCEIVER transmitter must be installed to provide a separation distance of at least 20cm from all person and not be colocated with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures.” BEFORE APPLYING POWER! • Check power and ground for proper polarity. • Read the rest of this manual. TROUBLESHOOTING There are no user serviceable parts in the MOD164 Transceiver. Contact your KARTECH representative for further instructions or servicing. PARTS LIST PART NUMBER DESCRIPTION 021641A MOD164 RADIO TRANSCEIVER – WIRE ANTENNA 021642A MOD164 RADIO TRANSCEIVER – RPSMA ANTENNA There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service. The information, specifications, and illustrations in this manual are those in effect at the time of printing. We reserve the right to change specifications or design at any time without notice. MOD164 TRANSCEIVER TRANSCEIVER PICTORIAL SPECIFICATIONS Equipment Class ............................. Part 15 Spread Spectrum Transmitter FCC ID ............................................................................ P4U-MOD164 ICC (Industry Canada Certification) ID ............................. 4534A-MOD164 TRANSCEIVER Power supply ........................................................................... 3.3VDC Operating temperature - Radio....................................... -40°C to +85°C Storage temperature .................................................. -40°C to +100°C RF Frequency ................................................................ 902.5-927 MHz RF Transmit power (EIRP) ......................................................... 100 mW RF Receive Sensitivity ............................................................. -126 dBm MOD164 TRANSCEIVER INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. MOD164 TRANSCEIVER INDUSTRY CANADA STATEMENTS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à l'établissement d'une communication satisfaisante. 10 MOD164 TRANSCEIVER OEM Responsibilities to comply with FCC and Industry Canada Regulations The MOD164 Transceiver has been certified for integration into products only by the OEM integrators under the following conditions: This device is granted for use in Mobile only configurations per Part 2.1091(b) in which the antennas used must be installed to provide a separation distance of at least 20cm from all person and not be colocated with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. As long as the two conditions above are met, further transmitter testing will not be required. However the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed. If the above conditions are not met, then the FCC and Industry Canada authorizations are no longer valid and the FCC ID and IC Certification Number cannot be used on the final product. In these cases the OEM integrator is responsible for re-evaluating the end product and obtaining a separate FCC and Industry Canada authorization. Recertification is also needed for all other operating configurations, including portable configurations with respect to part 2.1093 and different antenna configurations. 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Title : Microsoft Word - User's manual.doc Creator : user-109 Create Date : 2014:05:28 11:28:13-05:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2014:06:05 16:46:04-04:00 Metadata Date : 2014:06:05 16:46:04-04:00 Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:52962e8b-2c42-48fe-9f50-5efba941a288 Instance ID : uuid:5e4415f2-c992-4f6b-9bf9-efa03281986c Page Count : 12 Author : user-109EXIF Metadata provided by EXIF.tools