Netgear orporated 14200276 N750 Wireless Dual Band Gigabit Router User Manual Statement
Netgear Incorporated N750 Wireless Dual Band Gigabit Router Statement
Contents
- 1. User Manual (Statement).pdf
- 2. User Manual.pdf
User Manual (Statement).pdf
![](/img.php?id=2459824&img=bg1.png)
Notification of Compliance
Regulatory Compliance Information
This document includes user requirements for operating NETGEAR products in accordance with national laws
including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the
applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable
national regulatory authority.
The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country.
Therefore, all options described in this document may not be available in your version of the product.
This document applies to both Class A and Class B devices:
Class A devices are intended to be used in a commercial or industrial environment. They are not intended
to be used in a residential home or be available for general public use.
Class B devices are intended to be used in a residential setting, and may also be used in commercial and
industrial applications. Examples of Class B devices are telephones, personal computers, and residential
data gateways.
Fuses should only be installed by service personnel.
NETGEAR recommends the use of 26 AWG or larger gauge phone line cords.
Europe – EU Declaration of Conformity
This section applies to products bearing the CE or CE! mark:
Products bearing the CE or CE! mark comply with the following EU directives:
EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
Ecodesign Directive 2009/125/EC
RoHS Directive 2011/65/EU
If the product has telecommunications functionality, it also complies with the requirement of the following EU
directive:
R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards that are noted in the EU
Declaration of Conformity. The EU CE Declaration of Conformity may be found at
http://support.netgear.com/app/answers/detail/a_id/11621/.
Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be
aware that outdoor installations require special attention and will only be handled by trained and qualified installation
personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when
external antennas, power and grounding must be installed for use. Particular attention has to be given allowed
operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if
this product requires the special considerations for outdoor installations. For detailed iformation concerning
installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ )
![](/img.php?id=2459824&img=bg2.png)
The following paragraphs apply to WN2500RP:
This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU
member states, EFTA states, and Switzerland.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to
use the device for setting up outdoor radio links and/or for applying public access to telecommunications and/or
network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may
be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should
contact the national spectrum authority in France.
Warning
NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference
in which case the user may be required to take adequate measures.
FCC Requirements for Operation in the United States
Information in this section applies to products bearing the FCC mark (or statement):
FCC Information to User
This NETGEAR product does not contain any user serviceable components and is to be used with approved
antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and
approvals.
The following statement applies to these products:
C6300
GS608v4
WN370
D6000
HMNC100
WN1000v4
D6010
JNR1010v2
WN2500RP
D3600
JR6150
WN3000RPv2
D3610
JWNR2000v5
WN3500RP
D6200V2
JWNR2010v5
WNA1000Mv2
EX2700
R6050
WNDR3400v3
EX6100
R6200v3
WNDR3700v5
EX6200
R6220
WNR2010
FS205v2
R7500
WNR2020
FS605v4
R8000
WNR614
GS205v2
STS7000
WNR618
GS208v2
VEGN2200
GS305
VMB3000
GS308v2
VMC3010
GS605v5
VMC3030
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
● WNDR4300v2
FCC Guidelines for Human Exposure
The NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The
equipment should be installed and operated with minimum distance of 20cm between the radiator and your body.
The following statement applies to this product:
C6300XB3
This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device
should be installed and operated with minimum distance of 25cm between the radiator and your body.
The following statement applies to this product:
R8000
This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device
should be installed and operated with minimum distance of 30cm between the radiator and your body.
FCC Declaration of Conformity
We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this
product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:
The device may not cause harmful interference, and
The device must accept any interference received, including interference that may cause undesired
operation.
FCC Radio Frequency Interference Warnings & Instructions
The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following methods:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure and SAR Statements
The information in this section applies to products that transmit data or communicate wirelessly.
SAR Statement
The information in this section applies to NETGEAR wireless products that are intended to be operated close to
human body.
NETGEAR products that are intended to be operated close to the human body are tested for body-worn Specific
Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg.
The FCC has established detailed SAR requirements and NETGEAR products meet these requirements.
NETGEAR products comply with ANSI/IEEE C95.1-1999 and are tested in accordance with the measurement
methods and procedures specified in OET Bulletin 65 Supplement C.
NETGEAR products that are installed in USB ports demonstrate SAR compliance using a typical laptop computer
with a USB port. Other applications, such as handheld computers or similar devices, have not been verified and might
not compliance with related RF exposure rule and such use is prohibited.
RF Exposure Information
NETGEAR products have been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the
requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio
frequency devices. NETGEAR products meet the applicable government requirements for exposure to radio
frequency waves. To see the test results reporting the highest SAR level measured for this device, visit
http://www.netgear.com/about/regulatory/declarations-conformity/
Radiation exposure: NETGEAR products comply with radiation exposure limits set forth for an uncontrolled
environment and meet radio frequency (RF) exposure guidelines for wireless routers. NETGEAR products should be
installed and operated keeping the product 20cm or more away from a person’s body. For devices that are battery
powered and may be operated closer than 20cm to you, refer to the NETGEAR website for exposure levels.
NETGEAR USB dongle transmitters are approved for use in typical laptop computers. To comply with FCC RF
exposure requirements, do not use NETGEAR USB dongle transmitters in other devices or certain laptop and tablet
computer configurations where the USB connectors on the host computer are unable to provide or ensure the
necessary operating configurations intended for the device and its users or bystanders to satisfy RF exposure
compliance requirements.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
NETGEAR products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference
received, including interference that may cause undesired operation.
For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not
possible.
The following statement applies to these products:
C6300
JNR1010v2
VMB3000
WNDR3400v3
D6000
JR6150
VMC3010
WNDR3700v5
D6010
JWNR2000v5
VMC3030
WNR1000v4
D3600
JWNR2010v5
WAC120
WNR2010
D3610
R6050
WN370
WNR2020
D6200V2
R6200v3
WN2500RP
WNR614
EX2700
R6220
WN3000RPv2
WNR618
EX6100
R7500
WN3000RPv3
EX6200
R8000
WN3500RP
HMNC100
VEGN2200
WNA1000Mv2
The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
The following statement applies to these products:
● WNDR4300v2
A6210
EX6200
WNA1000Mv2
C6300
HMNC100
WN2500RP
C6300XB3
JR6150
WNDR3400v3
D6000
R6050
WNDR3700v5
D6010
R6200v3
D3600
R6220
D3610
R7500
D6200V2
R8000
EX6100
STS7000
The device operates in 5.15~5.25GHz frequency range. It is restricted in indoor environment only.
The following statements apply to this product:
A6210
WAC120
WNDR3400v3
The device operates in 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range. It is restricted in indoor environment only.
The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by
the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Non-DFS Warning
NETGEAR non-DFS products do not support operation in the 5600-5650MHz band. The firmware on the device
restricts the operation in this frequency band and does not utilize the channels in this band.
NETGEAR non-DFS products will not permit operations on channels 120–132 for 11a and 11n/a, which overlap the
5600–5650MHz band.
The following statements apply to these products:
A6210
HMNC100
R8000
WNDR3400v3
NETGEAR DFS products do not support operation in the 5600-5650MHz band. The firmware on the device restricts
the operation in this frequency band and does not utilize the channels in this band.
NETGEAR DFS products will not permit operations on channels 120–132 for 11a and 11n/a, which overlap the 5600–
5650MHz band.
Country Code Selection Usage (WLAN devices)
The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all
WiFi product marketed in US must fixed to US operation channels only.
TV Tuner (on Selected Models)
The information in this section applies to NETGEAR products incorporating a TV tuner.
Note to CATV System Installer: This reminder is provided to call the CATV system installer’s attention to Section 820-
93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that the
Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as
possible.
● WNDR4300v2
Canadian Department of Communications Radio Interference
Regulations
The information in this section applies to products bearing the statements:.
“This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus
as set out in the Radio Interference Regulations of the Canadian Department of Communications.”
“Cet appareil numérique ne dépasse pas les limites de la classe B pour les émissions radio bruit des
appareils numériques, tel qu'énoncé dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.”
CAN ICES-3 (B)/NMB-3(B)
CAN ICES-3 (A)/NMB-3(A)
Industry Canada
NETGEAR products comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products
must accept any interference received, including interference that may cause undesired operation.
A6210
JR6150
VMB3000
WNDR3700v5
D6000
JWNR2000v5
VMC3010
WNR1000v4
D6010
JWNR2010v5
VMC3030
WNR2010
D3600
R6050
WAC120
WNR2020
D3610
R6200v3
WN3000RPv3
WNR614
EX2700
R6220
WN370
WNR618
HMNC100
R7500
WNA1000Mv2
JNR1010v2
R8000
WNDR3400v3
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
A6210
JR6150
VMB3000
WNDR3700v5
D6000
JWNR2000v5
VMC3010
WNR1000v4
D6010
JWNR2010v5
VMC3030
WNR2010
D3600
R6050
WAC120
WNR2020
D3610
R6200v3
WN3000RPv3
WNR614
EX2700
R6220
WN370
WNR618
HMNC100
R7500
WNA1000Mv2
JNR1010v2
R8000
WNDR3400v3
The following statements apply to this product:
R7500
VMB3000
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is
not more than that necessary for successful communication.
● WNDR4300v2
● WNDR4300v2
![](/img.php?id=2459824&img=bg7.png)
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire
les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés
ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types
d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits
pour l'exploitation de l'émetteur.
Antenna type: Dipole
Antenna gain
The following antenna table applies to VMB3000 product:
The following antenna table applies to R7500 product:
IMPORTANT NOTE: Radiation Exposure Statement
NETGEAR products comply with IC radiation exposure limits set forth for an uncontrolled environment. NETGEAR
products should be installed and operated with minimum distance 20cm between the radiator and your body.
The following statement applies to this product:
R8000
This product complies with IC radiation exposure limits set forth for an uncontrolled environment. NETGEAR
products should be installed and operated with minimum distance 30cm between the radiator and your body.
NETGEAR products comply with the Canada portable RF exposure limit set forth for an uncontrolled environment
and are safe for intended operation as described in its manual. Further RF exposure reduction can be achieved by
keeping the product as far as possible from your body or by setting the device to a lower output power if such a
function is available.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is
not possible.
The following statement applies to these products:
D6000
JNR1010v2
STS7000
WNA1000Mv2
D6010
JR6150
VEGN2200
WNDR3400v3
D3600
JWNR2000v5
VMB3000
WNDR37000v5
D3610
JWNR2010v5
VMC3010
WNR1000v4
D6200V2
R6050
VMC3030
WNR2010
EX2700
R6200v3
WN370
WNR2020
EX6100
R6220
WN2500RP
WNR614
EX6200
R7500
WN3000RPv2
WNR618
HMNC100
R8000
WN3000RPv3
The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with IC multi-transmitter product procedures.
The following statement applies to these products:
A6210
HMNC100
WAC120
D6000
JR6150
WN2500RP
D6010
R6050
WNA1000Mv2
D3600
R6200v3
WNDR3400v3
D3610
R6220
WNDR3700v5
D6200V2
R7500
EX6100
R8000
EX6200
STS7000
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-
channel mobile satellite systems.
DFS warning:
NETGEAR DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-
5600MHz, and 5650-5725MHz:
The following statements apply to this product:
A6210
WNDR4300v2
● WNDR4300v2
the maximum antenna gain permitted for devices in the band 5725 - 5825 MHz shall comply with the e.i.r.p. limits specified
for point-to-point and non point-to-point operation as appropriate.
The following statements apply to this product:
C6300XB3
HMNC100
R8000
STS7000
WAC120
WNDR3400v3
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz to comply with
the EIRP (Equivalent Isotropically Raditaed Power) limit.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN
devices.
The following statement applies to this product:
WAC120
The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the EIRP (Equivalent
Isotropically Raditaed Power) limits specified for point-to-point and non point-to-point operation as appropriate.
SAR warning:
NETGEAR product is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and
had been tested in accordance with the measurement methods and procedures specified in IEEE 1528.
NOTE IMPORTANTE: Déclaration d'exposition aux radiations
Produits NETGEAR sont conformes aux limites IC d'exposition aux rayonnements définies pour un environnement
non contrôlé. Produits NETGEAR doivent être installés et utilisés avec distance minimum de 20cm entre le radiateur
et votre corps.
La déclaration suivante s'applique à ce produit :
R8000
Ce produit est conforme aux limites IC d'exposition aux rayonnements définies pour un environnement non contrôlé.
Produits NETGEAR doivent être installés et utilisés avec un minimum de 30cm entre le radiateur et votre corps.
Produits NETGEAR sont conformes à la limite d'exposition aux RF portable Canada établies pour un environnement
non contrôlé et sont sans danger pour le fonctionnement prévu comme décrit dans le manuel. Poursuite de la
réduction de l'exposition aux RF peut être réalisé en gardant le produit autant que possible de votre corps ou par le
réglage du dispositif à une puissance de sortie inférieure si une telle fonction est disponible
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités.
Sélection d'autres canaux n'est pas possible.
La déclaration suivante s'applique à ces produits:
D6000
JNR1010v2
STS7000
WNA1000Mv2
D6010
JR6150
VEGN2200
WNDR3400v3
D3600
JWNR2000v5
VMB3000
WNDR37000v5
D3610
JWNR2010v5
VMC3010
WNR1000v4
D6200V2
R6050
VMC3030
WNR2010
EX2700
R6200v3
WN370
WNR2020
EX6100
R6220
WN2500RP
WNR614
EX6200
R7500
WN3000RPv2
WNR618
HMNC100
R8000
WN3000RPv3
● WNDAR4300v2
● WNDR4300v2
![](/img.php?id=2459824&img=bga.png)
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre
antenne ou transmetteur.
La déclaration suivante s'applique à ces produits:
A6210
HMNC100
WAC120
D6000
JR6150
WN2500RP
D6010
R6050
WNA1000Mv2
D3600
R6200v3
WNDR3400v3
D3610
R6220
WNDR3700v5
D6200V2
R7500
EX6100
R8000
EX6200
STS7000
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
DFS avertissement:
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-
5600 MHz et 5650-5725 MHz :
Les instructions suivantes s'appliquent à ce produit:
A6210
C6300XB3
HMNC100
R8000
STS7000
WAC120
WNDR3400v3
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se
conformer à la limite de p.i.r.e.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés
utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces
radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
La déclaration suivante s'applique à ce produit;
WAC120
Avertissement SAR:
NETGEAR est le respect de SAR pour la population générale / limites d'exposition incontrôlée de CNR-102 et a été
testé en conformité avec les méthodes et procédures de mesure spécifiées dans la norme IEEE 1528.
Interference Reduction Table
The table below shows the Recommended Minimum Distance between NETGEAR equipment and household
appliances to reduce interference (in feet and meters).
Household Appliance
Recommended Minimum Distance (in feet and meters)
Microwave oven
30 feet / 9 meters
Baby monitor – analog
20 feet / 6 meters
Baby monitor – digital
40 feet / 12 meters
Cordless phone – analog
20 feet / 6 meters
● WNDR4300v2
● WNDR4300v2
![](/img.php?id=2459824&img=bgb.png)
Cordless phone – digital
30 feet / 9 meters
Bluetooth device
20 feet / 6 meters
ZigBee
20 feet / 6 meters
Japan Notices VCCI
This information in this section applies to products bearing the VCCI mark:
Class A ITE
この装置は、クラス A 情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがありま す
。この場合には使用者が適切な対策を講ずるよう要求されることがあります。
Class B ITE
この装置は、クラスB情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この装置
がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。
Japan Wireless Notice
この製品には、認証済みの無線機器を搭載しています。
South Korea Notices
The information in this section applies to products bearing the KCC mark:
알림 : 대한민국으로 배송되는 제품인 경우
Class A :
A급 기기
(업무용 방송통신기자재)
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을
주의하시기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
Class B :
B급 기기
(가정용 방송통신기자재)
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을
목적으로 하며, 모든 지역에서 사용할 수 있습니다.
Taiwan WWAN Wireless Notice
The information in this section applies to products bearing the Taiwan National Communications Commission mark:
This telecom equipment has complied with NCC regulations.
第十二條→經型式認證合格之低功率射頻電機,非經許可,公司,商號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用
,並改善至無干擾時方得繼續使用。
前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療
用電波輻射性電機設備之干擾。
在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備,限於室內使用。
無線資訊傳輸設備忍受合法通信之干擾且不得干擾合法通信;如造成干擾,應立即停用,俟無干擾之虞,
始得繼續使用。
無線資訊傳設備的製造廠商應確保頻率穩定性,如依製造廠商使用手冊上所述正常操作,發射的信號應維
持於操作頻帶中。
不致造成違反低功率電波輻射性電機管理辦法之所有控制、調整及開關之使用方法
對任何可能造成違反管理辦法規定之調整予以警告,或建議由具有發射機維修專長之技術人員執行或由其
直接監督及負責
對任何可能造成違反管理辦法之零件(晶體、半導體等)置換之警告
下列聲明適用於本產品:
R7500
電磁波曝露量MPE標準值1mW/cm2,送測產品實測值為:0.783945 mW/cm2
Thailand Notice
The information in this section applies to products approved by the Thailand National Communications Commission:
.
China Notices
The information in this section applies to products bearing the Chinese Complusory Certification Mark:
![](/img.php?id=2459824&img=bgd.png)
This device complies with the requirements in China for Safety and Quality
此为A级产品,在生活环境该产品可能会造成无线电干扰,在这种情况下可能需
要用户对其干扰采取确实可行的措施。
Australia and New Zealand Notices
The information in this section applies to products bearing the Australia C-Tick and A-Tick Compulsory Marks:
This device equipment complies with the Australian and New Zealand regulatory approvals requirements.
Warning
NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference
in which case the user may be required to take adequate measures.
LITHIUM ION AND LITHIUM METAL BATTERY PACKAGING LABEL
REQUIREMENTS
Due to concerns about products shipping with Li-Ion and Li-Metal batteries, the UN developed guidelines regarding
the proper testing, packaging, and labeling of these devices.
Li-Ion and Li-Metal Batteries
Li-Ion batteries are generally rechargeable, while Li-Metal batteries are generally non-rechargeable. Both types of
batteries have the potential to create a fire hazard if damaged or improperly packaged.
Labeling Requirements for Li-Ion and Li-Metal Batteries
The required labels must be present on the pallets and master carton accompanied by a document such as an airway
bill or other documents that indicates the following (Lithium Battery Guidance Document 2014):
The package contains lithium ion cells or batteries;
The package must be handled with care and that a flammability hazard exists if the package is damaged
Special procedures that should be followed in case the package is damaged
Contact information
To conform to IATA’s Dangerous Good Regulations, different labels apply to different Watt-hour for Li-Ion and
different mass for Li-metal. The calculation for Watt-hours is:
Nominal Voltage x Nominal Capacity (Ah) = Watt-hours
The volts and ampere can be found in the batteries data sheet.
![](/img.php?id=2459824&img=bge.png)
Please see Table below for which proper label to use.
Required Labels for Battery Transportation (UN Manual of Tests and Criteria Part III Subsection 38.3)
Li-Ion Battery Label Requirements
Shipment of Battery
Wh (Watt-hour)
Labels
Limit Battery Weight / Package
Contained in Equipment
(installed in the equipment)
Equal to or Less than 100Wh
Figure 12 or 13
PAX = 5 kg
CAO = 5kg
Alone
Equal to or Less than 100Wh
Figure 12 or 13
Equal to or less than 2.7 Wh=2.5 kg
OR
Greater than 2.7Wh but equal to or
less than 100Wh = 2 batteries
Packed separately with the
Equipment (not installed in the
equipment)
Equal to or Less than 100Wh
Figure 12 or 13
PAX = 5 kg
CAO = 5kg
Li-Metal Battery Label Requirements
Shipment of Battery
Mass of Lithium Metal of the
battery
Labels
Limit Battery Weight / Package
Contained in Equipment
(installed in the equipment)
Equal to or Less than 2g
Figure 12 or 13
PAX = 5 kg
CAO = 5kg
Alone
Equal to or Less than 2g
Figure 12 or 13
Equal to or less than 0.3g=2.5kg
OR
Greater than 0.3g but equal to or
less than 2g = 2 batteries
Packed separately with the
Equipment (not installed in the
equipment)
Equal to or Less than 2g
Figure 12 or 13
PAX = 5 kg
CAO = 5kg
If Li-Ion Battery is more than 100Wh and Li-Metal has a Lithium mass of more than 2g, please consult Environmental
Compliance Engineer for proper label to be used.
Label content requirement for shipping batteries:
![](/img.php?id=2459824&img=bgf.png)
Label content for shipping smaller packages for batteries:
Exemptions for labeling
A lithium ion battery handling label is not required when a package contains not more than 2 batteries contained in
the equipment. Lithium metal batteries contained in the equipment do not need any lithium battery handling label.
Product disposable warning
NETGEAR products must not be disposed of together with domestic waste. NETGEAR products must be disposed of
at a location that is authorized to recycle electrical and electronic appliances. By collecting and recycling waste, you
help save natural resources and make sure that the product is disposed of in an environmentally friendly and healthy
way.
Tuner Cable and Battery Safety Information
Tuner Cable:
This reminder is provided to call the CATV systems installer’s attention to Section 820-93 of the National Electric
Code which provide grounding and , in particular, specify that the Coaxial cable shield shall be connected to the
grounding system of the building, so close to the point of cable entry as practical.
Battery Caution:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Powerline Device Safety Information
Follow these safety guidelines to ensure your own personal safety and to help protect your system from potential
damage:
For national approvals (approval schemes other than CB), relevant national standards for plug, socket-
outlet, and direct plug-in units (for example, US) shall also be consulted while testing and approving such
products according to the national standards.
Check the electrical current for any device plugged into the filtered AC socket. Do not exceed home and
product outlet ratings and electrical requirements.
The socket-outlet shall be installed near the equipment and be easily accessible
Only power cords and allowed to be inserted into the filtered AC socket; no other equipment with a direct
plug-in is allowed. Power cords needs to be a maximum of 1m long and a minimum of 0.75mm² of cross-
sectional area.
Do not plug devices into the Powerline Pass Thru Adapter filtered AC outlet that exceed the product ratings.
The output voltage of the filtered AC outlet is the same as the power outlet that the Powerline Pass Thru
Adapter is plugged into. To help avoid damaging your system, be sure that the attached devices are
electrically rated to operate with the power available in your location.
If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket of the Powerline
Pass Thru Adapter might not perform as well as expected.
DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached power strip.
The device is not intended to be used with home appliances such as air conditioners, power tools, space
heaters, fans hair dryers, ovens, or refrigerators.
Actual data throughput will vary. Network conditions and environmental factors, including volume of network
traffic, building materials and construction, and network overhead, lower actual data throughput rate.
Do not service any product except as explained in your system documentation.
Opening or removing covers that are marked with the triangular symbol with a lightning bolt can expose you
to electrical shock. Only a trained service technician should service components inside these
compartments.
Use the product only with approved equipment.
Allow the products to cool before removing covers or touching internal components.
To help avoid damaging your system, be sure that the voltage selection switch (if provided) on the power
supply is set o match the power available at your location:
o 110 volts (V), 60 hertz (Hz) in most of North and South America and some Far Eastern countries
such as south Korea and Taiwan
o 100, 50 Hz in eastern Japan and 100, 60Hz in western Japan
o 230v, 50Hz in most of Europe, the Middle East, and the Far East
The peripheral power cables are equipped with three-prong plugs to help ensure proper grounding. Do not
use adapter plugs or remove the grounding prong from a cable.
Observe extension cable and power strip ratings. Make sure that the total ampere rating of all products
plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for te
extension cable or power strip.
To help protect your system from sudden, transient increases and decreases in electrical power, use a
surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Rack Mount Safety Instructions
This information applies to the installation of NETGEAR rack mount products
Ambient operating temperature. If the switch is installed in a closed or multiunit rack assembly, the
ambient operating temperature of the rack environment might be greater than the ambient temperature of
the room. Therefore, consider installing the equipment in an environment compatible with the maximum
rated ambient temperature.
![](/img.php?id=2459824&img=bg11.png)
Reduced airflow. Mount the equipment into a rack so that the amount of airflow required for safe operation
is not compromised.
Mechanical loading. Mount the equipment into a rack so that a hazardous condition does not arise due to
uneven mechanical loading.
Circuit overloading. Consider the equipment’s connection to the power supply circuitry and the effect that
any possible overloading of circuits might have on overcurrent protection and power supply wiring. Consider
equipment nameplate ratings when addressing this concern.
Reliable grounding. This product requires reliable grounding to be maintained at all times. To ensure this,
ground the rack itself. Pay particular attention to power supply connections other than the direct connections
to the branch circuit (for example, the use of power strips).
Clearance. Leave enough clearance in front of the rack (about 25 inches) to enable you to open the front
door completely and in the back of the rack (about 30 inches) to allow for sufficient airflow and ease in
servicing.
NETGEAR, Inc., 350 E. Plumeria Avenue, San Jose, CA 95134 USA
July 2014