Netgear orporated WAG311 Netgear 802.11 a/g Wireless PCI Adapter User Manual FullManual
Netgear Incorporated Netgear 802.11 a/g Wireless PCI Adapter FullManual
Contents
- 1. Users Manual Revised
- 2. DoC
Users Manual Revised
![](/img.php?id=352059&img=bg1.png)
M-10148-01
Version v1.0
June 2003
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Installation Guide for the
NETGEAR 54 Mbps
Wireless PCI Adapter
WAG311
![](/img.php?id=352059&img=bg2.png)
ii
Technical Support
Please refer to the support information card that shipped with your product. By registering your
product at www.netgear.com/register, we can provide you with faster expert technical support and
timely notices of product and software upgrades.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support
information card.
E-mail: support@netgear.com
Web site: www.netgear.com
This manual is written for the WAG311 Wireless PCI Adapter according to these specifications.:
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
©2003 NETGEAR, Inc. NETGEAR, the NETGEAR logo, The Gear Guy and Everybody's Connecting are
trademarks or registered trademarks of NETGEAR, Inc. in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
Table 0-1. Manual Specifications
Product Version NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Firmware Version Number ?
Manual Part Number M-10148-01
Manual Publication Date June 2003, Full Manual
Note: Product updates are available on the NETGEAR, Inc. web site at http://
www.netgear.com/support/main.asp. Documentation updates are available on the
NETGEAR, Inc. web site at http://www.netgear.com/docs.
![](/img.php?id=352059&img=bg3.png)
Beta
iii
other countries. Other brand and product names are trademarks or registered trademarks of their respective
holders. Information is subject to change without notice. All rights reserved.
Certificate of the Manufacturer/Importer
It is hereby certified that the Model WG311 Wireless PCI Adapter has been suppressed in accordance with the
conditions set out in the BMPT- AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example,
test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
VCCI Statement
This equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used
near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas
only. Any product changes or modifications will invalidate all applicable regulatory certifications and
approvals
FCC Guidelines for Human Exposure
In order to comply with RF exposure limits established in the ANSI C95.1 standards, the user is advised to maintain a
distance of at least 1 inch (2.5 cm) from the antenna of this device while it is in use.
FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Statement
NETGEAR 54 Mbps Wireless PCI Adapter WAG311
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
FCC ID: PY3WAG311
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environments
only.
![](/img.php?id=352059&img=bg4.png)
Beta
iv
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required
to correct the interference at his own expense.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Export Restrictions
This product or software contains encryption code which may not be exported or transferred from the US or
Canada without an approved US Department of Commerce export license.
Europe - EU Declaration of Conformity
This device complies with the essential requirements and other relevant provisions of the European R&TTE Directive
1999/5/EC. Compliance to essential test suites is met per standards:
R&TTE Harmonized Standard Description
LVD specification
EN 60950
EN 60950,ed. (1992), incl A1(1993), A2(1993), A3(1995) and
A4(1997)
Safety of information technology equipment, including electrical
business equipment.
Meets R&TTE directive art. 3.1.a of essential requirements on
protection of the health and safety of the user.
FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.This device may not cause harmful interference
2.This device must accept any interference received, including interference that may cause undesired operation.
![](/img.php?id=352059&img=bg5.png)
Beta
v
Canadian Department of Communications Radio Interference
Regulations
This digital apparatus (Model WAG311 Wireless PCI Adapter) does not exceed the Class B limits for radio-noise
emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Canada ID: 4054A-WAG311
ETSI EMC specification
ETSI EN 301 489-1 V1.2.1
(2000-08)
ETSI EN 301 489-17 V1.1.1
(2000-09)
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services;
Part 1: Common technical requirements
Part 17: Specific conditions for Wideband data and HIPERLAN
equipment
Meets R&TTE directive art. 3.1.b of essential requirements on
protection with respect to Electro Magnetic Compatibility.
ETSI RF specification
ETSI EN 300 328
Part 1 V1.2.2 (2000-07)
ETSI EN 300 328
Part 2 V1.1.1 (2000-07)
Electromagnetic compatibility and Radio spectrum Matters
(ERM); Wideband Transmission systems; data transmission
equipment operating in the 2,4 GHz ISM band and using spread
spectrum modulation techniques;
Part 1: Technical characteristics and test conditions
Part 2: Harmonized EN covering essential requirements
under article 3.2 of the R&TTE Directive
Meets R&TTE directive art. 3.2.a on effective use of spectrum so
as to avoid harmful interference.
0560!This device is a 2.4 GHz low power RF
device intended for home and office use in
EU and EFTA member states. In some EU /
EFTA member states some restrictions may
apply. Please contact local spectrum
management authorities for further details
before putting this device into operation.
![](/img.php?id=352059&img=bg6.png)
Beta
vi
Contents vii
Contents
Chapter 1
Introduction
About the NETGEAR 54 Mbps Wireless PCI Adapter WG311 .......................................1-1
Key Features and Related NETGEAR Products ............................................................1-1
What’s in the Box? ..........................................................................................................1-2
A Road Map for ‘How to Get There From Here’ .............................................................1-2
Chapter 2
Basic Setup
What You Will Need Before You Begin ...........................................................................2-1
Verify System Requirements ....................................................................................2-1
Observe Location and Range Guidelines ................................................................2-2
Two Basic Operating Modes ...........................................................................................2-2
WG311 Default Wireless Configuration Settings ............................................................2-3
Basic Installation Instructions .........................................................................................2-4
For Windows XP Users Installing a WG311 .............................................................2-4
For Windows 2000 & 98/Me Users Installing a WG311 ...........................................2-8
WG311 Wireless Connection Indicators .......................................................................2-12
Interpreting System Tray Icon Colors .....................................................................2-12
Basic Troubleshooting Tips ...........................................................................................2-13
About Page ...................................................................................................................2-14
Chapter 3
Configuration
Understanding the Configuration Options ......................................................................3-1
Using Configuration Profiles ...........................................................................................3-1
Networks Page .........................................................................................................3-2
Connect to an Access Point in Infrastructure Mode .................................................3-3
How to Configure an Infrastructure Mode Profile .....................................................3-3
Connecting to Another PC in Ad-Hoc Mode ...................................................................3-5
How to Configure an Ad-Hoc Mode Profile ..............................................................3-5
How to Start a Computer-to-Computer (Ad-Hoc) Network .......................................3-7
Enabling Wireless Security Features ..............................................................................3-8
viii Contents
Identifying the Wireless Network Name (SSID) and WEP Security Settings ...........3-9
How to Configure WEP Encryption Security ..........................................................3-10
Statistics Page ........................................................................................................3-12
Advanced Settings Page ........................................................................................3-13
Appendix A
Technical Specifications
Appendix B
Wireless Networking Basics
Wireless Networking Overview ...................................................................................... B-1
Infrastructure Mode ................................................................................................. B-1
Ad-Hoc Mode (Peer-to-Peer Workgroup) ................................................................ B-2
Network Name: Extended Service Set Identification (ESSID) ................................ B-2
Authentication and WEP ................................................................................................ B-2
802.11 Authentication .............................................................................................. B-3
Open System Authentication ................................................................................... B-3
Shared Key Authentication ...................................................................................... B-4
Overview of WEP Parameters ................................................................................ B-5
Key Size .................................................................................................................. B-6
WEP Configuration Options .................................................................................... B-6
Wireless Channels ......................................................................................................... B-7
Appendix C
Preparing Your PCs for Network Access
Preparing Your Computers for TCP/IP Networking ....................................................... C-1
Configuring Windows 98 and Me for TCP/IP Networking .............................................. C-1
Install or Verify Windows Networking Components ................................................. C-1
Enabling DHCP to Automatically Configure TCP/IP Settings in Windows 98 and Me C-3
Selecting the Internet Access Method ..................................................................... C-5
Verifying TCP/IP Properties .................................................................................... C-5
Configuring Windows 2000 or XP for TCP/IP Networking ............................................. C-6
Install or Verify Windows Networking Components ................................................. C-6
DHCP Configuration of TCP/IP in Windows XP or 2000 ......................................... C-7
DHCP Configuration of TCP/IP in Windows XP ..................................................... C-7
DHCP Configuration of TCP/IP in Windows 2000 .................................................. C-9
Verifying TCP/IP Properties for Windows XP or 2000 ........................................... C-11
xContents
![](/img.php?id=352059&img=bgb.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Introduction 1-1
Chapter 1
Introduction
This chapter introduces the features, package contents, and appearance of the NETGEAR® 54
Mbps WAG311 Wireless PCI Adapter.
About the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
The NETGEAR 54 Mbps Wireless PCI Adapter WAG311 gives you flexibility to install the PC in
the most convenient location available. The WAG311 frees you from traditional Ethernet wiring
that is limited by cabling requirements.
Its auto-sensing capability allows high packet transfer up to 54 Mbps (up to 108 Mbps in 802.11a
Turbo Mode) for maximum throughput or dynamic range shifting to lower speeds due to distance
or operating limitations in an environment with a lot of electromagnetic interference.
The WAG311 Wireless PCI Adapter provides reliable, standards-based 802.11a/g/bb Wireless
Local Area Network (WLAN) connectivity that is protected with industry-standard security. In
addition, it offers the faster speeds of the soon-to-be ratified 802.11g standard. The WAG311
works with Windows 98, Me, 2000, and XP operating systems.
802.11a and 802.11b/g Wireless Networking
The WAG311 Wireless PCI Adapter provides continuous, high-speed up to 54 Mbps access
between your wireless devices.
• 802.11a Standards-based wireless networking at up to 54 Mbps.
• 802.11g wireless networking at up to 54 Mbps, which will conform to the 802.11g standard
when ratified.
• 802.11b Standards-based wireless networking at up to 11 Mbps.
• 64-bit and 128-bit WEP encryption security.
• WEP keys can be generated manually or by passphrase.
• Wireless access can be restricted by MAC address.
![](/img.php?id=352059&img=bgc.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
1-2 Introduction
Key Features and Related NETGEAR Products
The WAG311 Wireless PCI Adapter provides the following features:
• Reliable IEEE 802.11b standards-based wireless technology.
• Supports roaming between access points when configured in Infrastructure mode.
• 54 Mbps high speed data transfer. Wireless nodes negotiate to operate in the optimal data
transfer rate. In a noisy environment or when the distance between the wireless nodes is far,
the wireless nodes automatically fall back to operate at lower transfer rates.
• High level of data encryption using128-bit Shared Key WEP data encryption method. Lower
level of data encryption or no data encryption is available to simplify your network setup or to
improve the data transfer rate.
The following NETGEAR products can be configured to communicate with the WAG311 Wireless
PCI Adapter:
• WG602 54 Mbps Wireless Access Point
• WGR614 54 Mbps Cable/DSL Wireless Router
• WGR511 54 Mbps Wireless PC Card
• MA111 802.11b Wireless USB Adapter
• ME103 802.11b ProSafe Wireless Access Point
• MA311 802.11b Wireless PCI Adapter
• MR814 802.11b Wireless Cable/DSL Routers
• MA521 802.11b Wireless Compact Flash Card
What’s in the Box?
The product package should contain the following items:
• NETGEAR 54 Mbps Wireless PCI Adapter WAG311
• Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
•NETGEAR 54 Mbps Wireless PCI Adapter WAG311 Resource CD (SW-10012-01), including:
— Configuration Utility Software
— Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WG311
• Warranty card
• Support information card
![](/img.php?id=352059&img=bgd.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Introduction 1-3
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
A Road Map for ‘How to Get There From Here’
The introduction and adoption of any new technology can be a difficult process. Wireless
technology has removed one of the barriers to networking—running wires. It allows more people
to try networking, while at the same time exposes them to the inherent complexity of networking.
General networking concepts, set up, and maintenance can be difficult to understand. In addition,
wireless technology adds issues such as range, interference, signal quality, and security to the
picture.
To help overcome potential barriers to successfully using wireless networks, the table below
identifies how to accomplish such things as connecting to a wireless network, assuring appropriate
security measures are taken, browsing the Internet through your wireless connection, exchanging
files with other computers and using printers in the combined wireless and wired network.
Table 1-1. A Road Map for How to Get There From Here
If I Want To ... ? What Do I Do? What’s Needed? How Do I?
Connect to a
wireless
network
1. Identify the
wireless
network name
(SSID) and, if
used, the
wireless
security
settings.
2. Set up the
NETGEAR 54
Mbps Wireless
PCI Adapter
WAG311 with
the settings
from step 1.
1. A wireless network
2. A desktop PC within the
operating range of the wireless
network. For guidelines about
the range of 802.11b/g
wireless networks, please see
“Observe Location and Range
Guidelines” on page 2-2.
To set up the WAG311, see
Chapter 2, “Basic Setup” and
follow the instructions provided.
To learn about wireless
networking technology, see
Appendix B, “Wireless
Networking Basics” for a general
introduction.
![](/img.php?id=352059&img=bge.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
1-4 Introduction
Protect my
wireless
connection from
snooping,
hacking, or
information
theft.
1. Assure that the
wireless
network has
security
features
enabled.
2. Configure my
WAG311 with
the security
settings of the
wireless
network.
3. Use Windows
security
features.
1. A wireless network with
authentication and WEP
encryption enabled.
2. Wireless networking
equipment that supports WEP
encryption, such as the
WAG311 and all NETGEAR
wireless networking products.
To learn about wireless
networking security, see
“Authentication and WEP Data
Encryption” on page B-2.
To use WEP security features,
please see “Enabling Wireless
Security Features” on page 3-8
and configure your WAG311
accordingly.
Note: Secure Internet sites such as banks and online merchants use encryption security built into browsers
like Internet Explorer and Netscape. Any wireless networking security features you might implement are in
addition to those already in place on secure Internet sites.
Connect to the
Internet over my
wireless
network.
1. Activate my
wireless link
and verify my
network
connection.
2. Open an
Internet
browser such
as Internet
Explorer or
Netscape
Navigator.
1. An active Internet connection
like those from cable or DSL
service providers.
2. A wireless network connected
to the cable or DSL Internet
service through a cable/DSL
router as illustrated in
“Connect to an Access Point in
Infrastructure Mode” on
page 3-3.
3. TCP/IP Internet networking
software installed and
configured on my PC
according to the requirements
of the Internet service provider
4. A browser like Internet
Explorer or Netscape
Navigator.
To configure your WAG311 in
Infrastructure Mode, see “Basic
Installation Instructions” on
page 2-4, and locate the section
for your version of Windows.
For assistance with configuring
the TCP/IP Internet software on
a PC, see “Preparing Your
Computers for TCP/IP
Networking” on page C-1 or refer
to the PC Networking Tutorial on
the NETGEAR 54 Mbps
Wireless PCI Adapter WAG311
Resource CD (SW-10012-01)
and the Help information
provided in the Windows system
you are using.
.
Table 1-1. A Road Map for How to Get There From Here
If I Want To ... ? What Do I Do? What’s Needed? How Do I?
![](/img.php?id=352059&img=bgf.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Introduction 1-5
Exchange files
between a
wirelessly
connected
notebook
computer and
other
computers in a
my combined
wireless and
wired
network.
1. Use the
Windows
Network
Neighborhood
feature to
browse for
computers in
the combined
wireless and
wired network.
2. Browse the
hard drive of
the target
computer in
the network in
order to locate
the directory or
files you want
to work with.
3. Use the
Windows
Explorer copy
and paste
functions to
exchange files
between the
computers.
1. The desktop computer I am
using to connect to the
wireless network needs to be
configured with the Windows
Client and File and Print
Sharing.
2. The desktop computer I am
using to connect to the
wireless network needs to be
configured with the same
Windows Workgroup or
Domain settings as the other
Windows computers in the
combined wireless and wired
network.
3. Any Windows networking
security access rights such as
login user name/ password
that have been assigned in the
Windows network or for
sharing particular files must be
provided when Windows
prompts for such information.
4. If so-called Windows ‘peer’
Workgroup networking is being
used, the drive, file system
directory, or file need to be
enabled for sharing.
For assistance with Windows
networking software, see
Appendix C, “Preparing Your
PCs for Network Access” for
configuration scenarios or refer
to the Help system included with
your version of Windows.
Windows Domain settings are
usually managed by corporate
computer support groups.
Windows Workgroup settings
are commonly managed by
individuals who want to set up
small networks in their homes, or
small offices.
For assistance with setting up
Windows networking, refer to the
PC Networking Tutorial on the
NETGEAR 54 Mbps Wireless
PCI Adapter WAG311 Resource
CD (SW-10012-01) and the Help
information provided in the
Windows system you are using.
Table 1-1. A Road Map for How to Get There From Here
If I Want To ... ? What Do I Do? What’s Needed? How Do I?
![](/img.php?id=352059&img=bg10.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
1-6 Introduction
Use printers in
a combined
wireless and
wired
network.
1. Use the
Windows
Printers and
Fax features to
locate
available
printers in the
combined
wireless and
wired network.
2. Use the
Windows Add
a Printer
wizard to add
access to a
network printer
from the PC
you are using
to wirelessly
connect to the
network.
3. From the File
menu of an
application
such as
Microsoft
Word, use the
Print Setup
feature to
direct your
print output to
the printer in
the network.
1. The desktop computer I am
using to connect to the
wireless network needs to be
configured with the Windows
Client and File and Print
Sharing.
2. The desktop computer I am
using to connect to the
wireless network needs to be
configured with the same
Windows Workgroup or
Domain settings as the other
Windows computers in the
combined wireless and wired
network.
3. Any Windows networking
security access rights such as
login user name/ password
that have been assigned in the
Windows network must be
provided when Windows
prompts for such information.
4. If so-called Windows ‘peer’
networking is being used, the
printer needs to be enabled for
sharing.
Windows Domain settings are
usually managed by corporate
computer support groups.
Windows Workgroup settings
are commonly managed by
individuals who want to set up
small networks in their homes, or
small offices.
For assistance with setting up
Windows networking, refer to the
PC Networking Tutorial on the
NETGEAR 54 Mbps Wireless
PCI Adapter WAG311 Resource
CD (SW-10012-01) and the Help
information provided in the
Windows system you are using.
For assistance with setting up
printers in Windows, refer to the
Help and Support information
that comes with the version of
the Windows operating systems
you are using.
Table 1-1. A Road Map for How to Get There From Here
If I Want To ... ? What Do I Do? What’s Needed? How Do I?
![](/img.php?id=352059&img=bg11.png)
Basic Setup 2-1
Chapter 2
Basic Setup
This section describes how to install your NETGEAR 54 Mbps Wireless PCI Adapter WAG311
and set up basic wireless connectivity on your Wireless Local Area Network (WLAN). Advanced
wireless network configuration is covered in Chapter 3, “Configuration” in this manual.
What You Will Need Before You Begin
You need to verify that your computer meets the minimum system requirements and identify the
wireless network configuration settings of the WLAN where you will connect before you can
configure your wireless PCI adapter and connect.
Verify System Requirements
Before installing the NETGEAR 54 Mbps Wireless PCI Adapter WAG311, please make sure that
these minimum requirements have been met:
• Pentium® III class computer with an available PCI slot
•CD-ROM drive
• 20 Mbytes of free hard disk space
• Some versions of Windows may ask for the original Windows operating system installation
files to complete the installation of the WAG311 driver software
Note: Indoors, computers can easily connect to 802.11 wireless networks at distances of
several hundred feet. Because walls do not always block wireless signals, others from
outside your immediate area could access your network. It is important to take
appropriate steps to secure your network from unauthorized access. The NETGEAR 54
Mbps Wireless PCI Adapter WAG311 provides highly effective security features which
are covered in “Enabling Wireless Security Features” on page 3-8. Deploy the security
features appropriate to your needs.
![](/img.php?id=352059&img=bg12.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-2 Basic Setup
Observe Location and Range Guidelines
Computers can connect over 802.11g wireless networks indoors at a range which varies
significantly based on the physical location of the computer with the NETGEAR 54 Mbps
Wireless PCI Adapter WAG311. For best results, avoid potential sources of interference, such as:
• Large metal surfaces
•Microwaves
• 2.4 GHz Cordless phones
In general, 802.11g wireless devices can communicate through walls. However, if the walls are
constructed with concrete, or have metal, or metal mesh, the 802.11g effective range will decrease
if such materials are between the devices.
Note: The 802.11a standard operates at a higher frequency and should be less susceptible to
interference with cordless phones. This higher 802.11a frequency may not offer as much range of
coverage as the lower frequency 802.11b/g in a indoor environment with lots of obstructions.
Two Basic Operating Modes
The WAG311 Wireless PCI Adapter, like all 802.11a/b/g adapters, can operate in the following
two basic modes:
•Infrastructure Mode: An 802.11 networking framework in which devices and computers
communicate with each other by first going through an access point (AP). For example, this
mode is used when computers in a house connect to an AP that is attached to a router which
lets multiple computers share a single Cable or DSL broadband Internet connection.
•Ad-Hoc Mode: An 802.11 networking framework in which devices or computers
communicate directly with each other, without the use of an access point. For example,
Ad-Hoc Mode is used when two Windows computers are configured with file and print
sharing enabled and you want to exchange files directly between them.
Both of these configuration options are available with the WAG311 Wireless PCI Adapter.
Infrastructure configuration procedures for basic network connectivity are covered below.
Advanced infrastructure configuration procedures and ad-hoc configuration are covered in
Chapter 3, “Configuration” of this manual.
![](/img.php?id=352059&img=bg13.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-3
WAG311 Default Wireless Configuration Settings
If this is a new wireless network installation, use the factory default settings to set up the network
and verify wireless connectivity. If this is an addition to an existing wireless network, you will
need to identify the wireless configuration and security parameters already defined.
Your NETGEAR 54 Mbps Wireless PCI Adapter WAG311 factory default basic settings are:
• Network Name Service Set Identification (SSID): ANY — a special name which indicates the
first available network will be used
Note: In order for the WAG311 Wireless PCI Adapter to communicate with a wireless access
point or wireless adapter, all devices must be configured with the same wireless network name
(SSID).
• Network Mode (Infrastructure or Ad-Hoc): Infrastructure
• Data security WEP encryption: Disabled
The section below provides instructions for setting up the NETGEAR 54 Mbps Wireless PCI
Adapter WAG311 for basic wireless connectivity to an access point. The procedures provide
step-by-step installation instructions for Windows PCs. Use the procedure that corresponds to the
version of Windows you are using.
![](/img.php?id=352059&img=bg14.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-4 Basic Setup
Basic Installation Instructions
Use the procedure below that corresponds to the version of Windows you are using.
For Windows XP Users Installing a WAG311
Install the WAG311 software.
a. Power on your computer, let the
operating system boot up completely,
and log in as needed.
b. Insert the NETGEAR 54 Mbps Wireless
PCI Adapter WAG311 Resource CD
(SW-10012-01) into your CD-ROM
drive. The CD main page shown at the
right will load.
c. Click the “Install Driver & Utility” link.
d. Follow the InstallShield Wizard steps,
and click Finish when done to restart
your computer.
WAG311 Resource CD
Note: If this page does not automatically appear,
browse the root of the CD and double-click on
autorun.exe to display this page.
Found New Hardware Wizard
Note: If a Windows XP Certification warning appears,
click Continue Anyway to proceed.
![](/img.php?id=352059&img=bg15.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-5
Install the NETGEAR 54 Mbps Wireless
PCI Adapter WAG311.
a. Shut down the PC and remove the power
cord. Hold the PCI Adapter with the
NETGEAR logo facing up and insert it
into an available PCI slot.
Connect the antenna to the adapter and
position the antenna to the up position.
Reconnect the power cord and reboot the
computer.
b. The Found New Hardware Wizard
displays. Click Next and follow the
prompts to proceed.
Click Continue Anyway if you are
prompted with a Windows XP Logo
testing message.
c. After the installation completes, click
Finish to close the wizard.
You should see the WAG311 system tray
icon on the lower right portion of the
Windows task bar.
Windows XP will display a Wireless
Network Connection message.
Add New Hardware Wizard
WAG311 System Tray Icon
Windows XP Network Connection Alert
![](/img.php?id=352059&img=bg16.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-6 Basic Setup
Configure your WAG311.
a. Right-click on the network icon in the
Windows XP system tray to open the
network options menu.
b. Click on the View Available Wireless
Networks menu item.
c. If there is more than one wireless
network in your vicinity, select the one
to which you will connect.
d. Click on the “Allow me to connect to the
selected wireless network even though
this is not secure” check box.
e. Click Connect.
Windows XP Network Connection Alert
Note: This procedure assumes your wireless network
is not using WEP security. If your wireless network
uses WEP, set up your WAG311 accordingly. To view
WEP settings help, click the Advanced button and
click the “Learn about...” link on the Windows XP Local
Area Connection Wireless Networks Properties tab
page.
Right-click here to display this menu.
![](/img.php?id=352059&img=bg17.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-7
Verify wireless connectivity to your network.
a. Open the WAG311 utility by clicking on the icon in the Windows system tray.
b. Verify that your connection information matches your wireless network.
c. Verify connectivity to the Internet or network resources.
Note: If you are unable to connect, see “Basic Troubleshooting Tips” on page 2-13.
Note: When the Windows XP
wireless configuration utility is
enabled (the default), only these two
tab pages appear.
To use the full NETGEAR utility, see
“Understanding the Configuration
Options” on page 3-1.
![](/img.php?id=352059&img=bg18.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-8 Basic Setup
For Windows 2000 & 98/Me Users Installing a WAG311
Install the WAG311 software.
Note: Windows 2000 may require you to be
logged on with administrator rights.
a. Power on your computer, let the
operating system boot up completely,
and log in as needed.
b. Insert the Resource CD for the WAG311
into your CD-ROM drive. The CD main
page shown at the right will load.
c. Click the “Install Driver & Utility” link.
d. Follow the InstallShield Wizard steps,
and click Finish when done to restart
your computer.
WAG311 Resource CD
InstallShield Wizard
![](/img.php?id=352059&img=bg19.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-9
Install the NETGEAR 54 Mbps Wireless
PCI Adapter WAG311.
a. Shut down the PC and remove the power
cord. Insert the WAG311 Wireless PCI
Adapter with the NETGEAR logo facing
up into an available PCI slot.
b. Reconnect the power cord and reboot the
computer. After a short delay, the Found
New Hardware Wizard displays.
c. Click Next and follow the prompts to
proceed. After the installation
completes, click Finish to close the
wizard.
You should see the WAG311 system tray
icon on the lower right portion of the
Windows task bar.
Add New Hardware Wizard
Note: If Windows displays a Digital Signature Not
Found warning, click Yes to continue.
WAG311 System Tray Icon
![](/img.php?id=352059&img=bg1a.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-10 Basic Setup
Configure your WAG311 and save the
Profile.
a. Open the WAG311 Smart Wireless
Settings Utility by clicking on the icon in
the Windows system tray. The utility
opens to the Settings page.
b. Change the Network Name SSID to
match your network.
Tip: As an alternative to typing in the
SSID, you can use the Network tab to
view the available wireless networks.
Double-click on the desired network.
c. Click the Apply button to activate the
connection.
d. Enter a name for your profile and click
the Save Profile button to store the
current settings.
Note: This procedure assumes you are
connecting to a wireless network which is not
using WEP security. If your network includes
WEP settings, enter the security information
in the Security section. For help with these
steps, see “Enabling Wireless Security
Features” on page 3-8.
WAG311 system tray icon
WAG311 Configuration Utility
Note: The NETGEAR default settings are
Infrastructure mode, with ANY for the wireless
network name SSID, and WEP disabled.
Click here to open the configuration utility.
![](/img.php?id=352059&img=bg1b.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-11
Verify wireless connectivity to your network.
a. Verify that your connection information matches your wireless network.
b. Verify connectivity to the Internet or network resources.
Note: If you are unable to connect, see “Basic Troubleshooting Tips” on page 2-13.
Note: You can use the Networks
tab to verify the availability of
wireless networks and their SSIDs.
For more information, see
“Understanding the Configuration
Options” on page 3-1.
![](/img.php?id=352059&img=bg1c.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-12 Basic Setup
WAG311 Wireless Connection Indicators
The NETGEAR 54 Mbps Wireless PCI Adapter WAG311 SysTray icon, which is on the System
Tray portion of the taskbar in the Microsoft Windows desktop, is an indicator that gives you
feedback on the status of your wireless connection. The color of the SysTray icon indicates the
status of the connection.
Interpreting System Tray Icon Colors
The System Tray (SysTray) resides on one end of the taskbar in the Microsoft Windows desktop.
Color Condition Description
Red The wireless PCI Adapter
has no connection to any
other wireless node.
The wireless PCI Adapter is not able to link to any
other wireless node or the link is lost. Check your
configuration or try moving to a location where the
wireless signal quality is better.
Yellow The wireless PCI Adapter
has a connection with
another wireless node.
The wireless link is weak. You may deed to move to a
better spot, such as closer to the wireless access point.
Also, look for possible interference such as a 2.4 GHz
cordless phone or large metal surface.
Green The wireless PCI Adapter
has a connection with
another wireless node.
The wireless PCI Adapter has established good
communication with an access point and the signal
quality is strong.
![](/img.php?id=352059&img=bg1d.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-13
Basic Troubleshooting Tips
If you have problems connecting to your wireless network, try the tips below.
Also, for problems with accessing network resources, the Windows software might not be installed
and configured properly on your computers. Please refer to Appendix C, “Preparing Your PCs for
Network Access” of the Reference Manual on the NETGEAR 54 Mbps Wireless PCI Adapter
WAG311 Resource CD (SW-10012-01).
Symptom Cause Solution
I can connect to
an access point,
but I cannot
connect to other
computers on
the network or
the Internet.
This could be a
physical layer
problem or a
network
configuration
problem.
Check to make sure that the access point is physically
connected to the Ethernet network.
Make sure that the IP addresses and the Windows
networking parameters are all configured correctly.
Restart the cable or DSL modem, router, access point,
and notebook PC.
![](/img.php?id=352059&img=bg1e.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-14 Basic Setup
About Page
The About page displays important information about the NETGEAR 54 Mbps Wireless PCI
Adapter WAG311.
Figure 2-1: About page
The About page shows the following information:
•Regional Domain: This is the region setting for the wireless adapter. The approved channels
for this region are automatically scanned. Governments regulate the channels used for wireless
transmission. Operating the wireless adapter in a different region may violate local laws.
•Driver Version: The wireless adapter driver version.
•Driver Date: The wireless adapter driver release date.
![](/img.php?id=352059&img=bg1f.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Basic Setup 2-15
•MAC Address: The MAC address of this adapter. The Media Access Control address is a
unique 48-bit hardware address assigned to every network interface card. Some wireless
networks will restrict access based on a list of known MAC addresses. If you are
communicating with such a network, you would have to provide the address shown here to the
network administrator before you would be allowed to connect. Restricting access by MAC
address adds an obstacle against unwanted access to your network. However, unless you use
data encryption security, the data broadcast over the wireless link is fully exposed.
•IP Address: The IP address assigned to this adapter.
•Configuration Utility Software: The version and release date of this utility.
![](/img.php?id=352059&img=bg20.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2-16 Basic Setup
![](/img.php?id=352059&img=bg21.png)
Configuration 3-1
Chapter 3
Configuration
This section describes how to configure your NETGEAR 54 Mbps Wireless PCI Adapter
WAG311 for wireless connectivity on your Wireless Local Area Network (WLAN) and use the
data security encryption features.
Understanding the Configuration Options
The WAG311 configuration utility provides a complete and easy to use set of tools to:
• Configure wireless settings.
• Monitor wireless network connections.
• Save your settings in configuration profiles.
The section below introduces these capabilities of the configuration utility.
Using Configuration Profiles
The WAG311 configuration utility uses profiles to store all the configuration settings for a
particular wireless network. You can store multiple profiles and recall the one which matches
the network you want to join.
Note: The instructions in this section refer to the NETGEAR WAG311 configuration
utility. Windows XP users must first disable the Windows XP configuration utility.
Open the network connections from the system tray icon, click the Properties button,
click the Wireless Networks tab and then clear the “Use Windows to configure my
wireless network settings” check box.
![](/img.php?id=352059&img=bg22.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-2 Configuration
For example, if you use your PC to connect to a wireless network in an office and a wireless
network in your home, you can create a profile for each wireless network. Then, you can easily
load the profile that has all the configuration settings you need to join the network you are using at
the time.
There are two types of wireless network connections you can configure:
•Infrastructure Mode — uses the 802.11 infrastructure mode.
•Ad-Hoc Mode — uses the 802.11 ad-hoc mode
For more information on 802.11 wireless network modes, see “Wireless Networking Overview”
on page B-1 of this manual.
Networks Page
The Networks page shows the available networks at your location.
Figure 3-1: Networks tab page
The Networks page displays the following fields:
![](/img.php?id=352059&img=bg23.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Configuration 3-3
•Wireless Network Name (SSID): Wireless Network Name (SSID) is the name assigned to a
wireless network. This is the same as the SSID or ESSID configuration parameter. Note that,
as a security measure, some wireless access points do not broadcast their SSID. In such cases,
the SSID field will be blank even though the rest of the information will still be displayed.
•Channel: The channel determines which operating frequency will be used.
•Security: Identifies if the wireless network requires WEP security settings.
•Signal: Identifies the signal strength of the communications.
•MAC Address: Identifies the hardware address (MAC Address) of the wireless device
broadcasting this information.
•Mode: Identifies the type of wireless network — Access Point (Infrastructure) or
Computer-to-computer (Ad-Hoc).
To connect to a network:
1. Click Scan to view the available networks.
2. Click on the column header to sort for better viewing if you have many networks.
3. Double-click to connect to the SSID.
4. The highlighted SSID is the one currently connected.
Connect to an Access Point in Infrastructure Mode
This section provides instructions for configuring the NETGEAR 54 Mbps Wireless PCI Adapter
WAG311 to connect to a wireless access point.
How to Configure an Infrastructure Mode Profile
Follow the instructions below to configure an infrastructure mode profile for connecting to an
access point.
1. Run the WAG311 Configuration Utility.
a. Open the configuration utility by clicking on the WAG311 icon in the Windows
system tray.
![](/img.php?id=352059&img=bg24.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-4 Configuration
b. Click on the Settings tab to display the view shown below.
Figure 3-2: Settings tab page
2. Configure the wireless Network settings.
a. In the Network Type section, be sure that Infrastructure is selected.
b. Enter the SSID. This is also called the Wireless Network Name.
Note: You will not get a wireless network connection unless the network SSID matches
exactly what is configured in the access point.
Tip: You can click the Networks tab to view a list of the available wireless networks and
their SSIDs at your location.
3. Save your settings in a Profile.
a. Type a descriptive name for the Profile in the “Profiles” name field.
b. Click Save Profile. All the configuration settings are saved in this profile.
c. Click Apply.
d. Click Close to exit the configuration utility or Cancel to return to the previous settings.
![](/img.php?id=352059&img=bg25.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Configuration 3-5
4. Verify wireless connectivity to your network.
Verify connectivity by using a browser such as Netscape or Internet Explorer to connect to the
Internet, or check for file and printer access on your network.
You can check the status bar in the configuration utility for the current connection status.
Note: If you cannot connect, see the “Basic Troubleshooting Tips” on page 2-13. Also, if you
have problems accessing network resources, the Windows Client and File and Print Sharing
software might not be installed and configured properly on your computers. Please refer to
“Preparing Your Computers for TCP/IP Networking” on page C-1.
Connecting to Another PC in Ad-Hoc Mode
The computer-to-computer setting of the WAG311 uses Ad-Hoc mode. Ad-Hoc mode is an 802.11
networking framework in which devices or computers communicate directly with each other,
without the use of an access point. For example, this mode is used when two Windows computers
are configured with file and print sharing enabled and you want to exchange files directly between
them.
How to Configure an Ad-Hoc Mode Profile
Note: Ad-Hoc mode will not work using DHCP settings. Ad-Hoc mode requires either static IP
addresses (such as 192.168.0.1) or other appropriate Windows networking configuration
parameters such as adding IPX protocol support. For instructions on setting up static IP addresses
or IPX protocol settings on a Windows PC, refer to the PC Networking Tutorial included on the
NETGEAR 54 Mbps Wireless PCI Adapter WAG311 Resource CD (SW-10012-01).
Follow the instructions below to configure an Ad-Hoc mode profile.
1. Run the WAG311 Configuration Utility.
a. Open the configuration utility by clicking on the WAG311 icon in the Windows
system tray.
![](/img.php?id=352059&img=bg26.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-6 Configuration
Figure 3-3: Settings tab page
b. Click the Settings tab to display the view shown above.
c. Select Ad-Hoc in the Network Type section.
d. Enter the SSID for the Ad-Hoc network.
e. Click Apply.
2. Save your settings in a Profile.
a. Type a descriptive name for the Profile Name.
b. Click Save Profile. All the configuration settings are saved in this profile.
c. Click Apply.
d. Click Close to exit the configuration utility.
3. Configure the PC network settings.
a. Configure each PC with either a static IP address or with the IPX protocol.
Note: For instructions on configuring static IP addresses or the IPX protocol, refer to the
networking tutorial on your NETGEAR 54 Mbps Wireless PCI Adapter WAG311 Resource
CD (SW-10012-01).
b. Restart the PCs.
4. Verify wireless connectivity between your peer devices.
Verify connectivity by using the Ping program:
a. On the Windows taskbar click the Start button, and then click Run.
![](/img.php?id=352059&img=bg27.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Configuration 3-7
b. Assuming the target PC is configured with 192.168.0.1 as its IP address, type ping -t
192.168.0.1 and then click OK.
c. This will cause a continuous ping to be sent to the device with the 192.168.0.1 static IP
address. The ping response should change to “reply.”
At this point the connection is established.
You may need to reboot in certain Windows operating systems such as Windows 98.
Note: If you cannot connect, see “Basic Troubleshooting Tips” on page 2-13. Also, if you
have problems accessing network resources, the Windows Client and File and Print Sharing
software might not be installed and configured properly on your computers. Please refer to
“Preparing Your Computers for TCP/IP Networking” on page C-1.
How to Start a Computer-to-Computer (Ad-Hoc) Network
Note: Ad-Hoc wireless networks require static IP address configurations. For more information on
configuring TCP/IP settings, please see the PC Networking Tutorial included on the NETGEAR 54
Mbps Wireless PCI Adapter WAG311 Resource CD (SW-10012-01).
1. Fill in the Network Name (SSID).
2. Select the Computer-to-Computer (Ad-Hoc) network type.
3. Click Initiate Ad-Hoc. The Ad-Hoc Setting dialog box will appear, as shown below.
![](/img.php?id=352059&img=bg28.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-8 Configuration
Figure 3-4: Ad-Hoc Setting page
4. In the Start Ad-Hoc field, choose the wireless standard (802.11b or 802.11g) for your Ad-Hoc
computer-to-computer network.
5. In the Channel field, Automatic should work. If you notice interference problems with another
nearby wireless device, select a channel that is not being used by any other wireless networks
near your wireless adapter. Use the Networks tab page to identify the channels in use in your
area.
6. Click OK.
Note: The channel number differs depending on the country. The connection speed automatically
defaults to the highest speed.
Enabling Wireless Security Features
You can strengthen the security of your wireless connection by enabling Wired Equivalent Privacy
(WEP) encryption of the wireless data communications. For more information on 802.11 wireless
security, see “Authentication and WEP Data Encryption” on page B-2.
In addition to the WAG311 wireless security features, you should also configure appropriate LAN
network security features such as requiring a user name and password to access the shared
resources in your network.
The procedures below identify how to configure the WEP encryption settings of your NETGEAR
54 Mbps Wireless PCI Adapter WAG311.
![](/img.php?id=352059&img=bg29.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Configuration 3-9
Before You Change the SSID and WEP Settings
Take the following steps. For a new wireless network, print or copy this form and fill in the
configuration parameters. For an existing wireless network, the person who set up or is responsible
for the network will be able to provide this information. .
•Network Name (SSID): The Network Nameidentifies the wireless local area network.
ANY is the default for the WAG311. You may customize it by using up to 32
alphanumeric characters. Write your customized SSID on the line below.
Note: The SSID in the wireless PCI adapter is what you the wireless network uses. All
wireless nodes in the same network must be configured with the same SSID.
802.11a SSID: ______________________________
802.11b/g SSID: ______________________________
• Authentication
The two bands can use different authentication settings. “Shared Key” is more security.
802.11a SSID, circle one: Open System or Shared Key
802.11b/g SSID, circle one: Open System or Shared Key
Note: If you select shared key, the other devices in the network will not connect unless
they are set to Shared Key as well.
• WEP Encryption
802.11a and 802.11b/g differ in their use of WEP encryption keys. See “Security
Configuration” on page 2-21 for a description of these differences.
802.11a WEP Encryption Keys
Key 1: ___________________________________ Circle Key Size: 64 or 128 or 152 bits
Key 2: ___________________________________ Circle Key Size: 64 or 128 or 152 bits
Key 3: ___________________________________ Circle Key Size: 64 or 128 or 152 bits
Key 4: ___________________________________ Circle Key Size: 64 or 128 or 152 bits
802.11b/g WEP Encryption Keys
For all four 802.11bg keys, choose the Key Size. Circle one: 64 or 128 bits
Key 1: ___________________________________
Key 2: ___________________________________
Key 3: ___________________________________
Key 4: ___________________________________
![](/img.php?id=352059&img=bg2a.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-10 Configuration
How to Configure WEP Encryption Security
Following the steps below to configure WEP Encryption Security.
1. Run the WAG311 Configuration Utility.
a. Open the configuration utility by clicking on the WAG311 icon in the Windows
system tray.
Figure 3-5: Settings tab page
b. Click on the Settings tab to display the view shown above.
2. Configure the Security settings.
a. Select the Use WEP Encryption check box.
b. Enter the SSID. This is also called the Wireless Network Name.
Note: You will not get a wireless network connection unless the network SSID matches
exactly what is configured in the access point.
![](/img.php?id=352059&img=bg2b.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Configuration 3-11
Tip: You can click the Networks tab to view a list of the available wireless networks and
their SSIDs at your location.
3. Save your settings in a Profile.
a. Type a descriptive name for the Profile name.
b. Click Save Profile. All the configuration settings are saved in this profile.
c. Click Apply.
d. Click Close to exit the configuration utility.
4. Select the WEP encryption strength you will use.
The choices are:
• 64-bit WEP data encryption
• 128-bit WEP data encryption
Note: Larger encryption keys require more processing and may slow the communications
response times.
5. Select Create with Passphrase and enter the passphrase. The configuration utility will
automatically generate the WEP keys.
Note: The characters are case sensitive. Be sure to use the same passphrase for all the wireless
devices in the network.
If the passphrase method is not available in the other devices, you must manually enter the
keys to match exactly what is in the access point and other 802.11b/g wireless devices.
6. The Default Key setting must match what is set in the access point and the other 802.11
wireless devices.
7. Click Apply for the changes to take effect.
![](/img.php?id=352059&img=bg2c.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-12 Configuration
Statistics Page
The Statistics page provides real time and historical trend information on the data traffic and
performance of your wireless adapter.
Figure 3-6: Statistics tab page
•Transmit/Receive Performance (%): A real time graph identifying the Total, Receive, and
Transmit utilization as a percentage the total possible.
•Total/Receive/Transmit Graph: Identifies the trend of transmit/receive data communications
over time.
•Transmit Statistics: Identifies Transmit megabits per second (Mbps), transmit packets per
second (Tx Packets/s), total transmitted packets, and transmit errors.
•Receive Statistics: Identifies Receive megabits per second (Mbps), receive packets per second
(Rx Packets/s), total received packets, and received errors.
![](/img.php?id=352059&img=bg2d.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Configuration 3-13
Advanced Settings Page
Generally, Advanced settings should not require adjustment. Except for the power saving setting,
changing any of the settings incorrectly on this page could cause your wireless connection to fail.
Figure 3-7: Advanced Settings page
•Power Saving: Select On if you are using a notebook computer running on battery power.
•Preamble: A long transmit preamble may provide a more reliable connection or slightly
longer range. A short transmit preamble might give slightly better performance.
•Transmit Power: Lowering the output power level lets you reduce the chance of interference
with other nearby access points but reduces the range of your adapter.
•Wireless Mode: Select the wireless protocols you will use. Depending on your wireless
adapter, you can choose some or all of the available 802.11 wireless protocols. Note that, if the
wireless network you are communicating with uses the 802.11a Turbo mode, you must include
that in your selection.
•Fragmentation Threshold: This is the maximum packet size used for fragmentation. Packets
larger than the size programmed in this field will be fragmented. The Fragment Threshold
value must be larger than the RTS Threshold value.
![](/img.php?id=352059&img=bg2e.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
3-14 Configuration
•RTS/CTS Threshold: The packet size that is used to determine whether it should use the
CSMA/CD (Carrier Sense Multiple Access with Collision Detection) mechanism or the
CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) mechanism for packet
transmission. CSMA/CD is slightly more efficient.
![](/img.php?id=352059&img=bg2f.png)
Technical Specifications A-1
Appendix A
Technical Specifications
This appendix provides technical specifications for the NETGEAR 54 Mbps Wireless PCI Adapter
WA G 3 11 .
Antennae 2 Integrated internal diversity antennae
Radio Data Rate 1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, and 54 Mbps (Auto Rate Sensing)
Frequency 2.4GHz to 2.5GHz CCK and OFDM Modulation)
Emissions FCC, CE, TELEC
Bus interface PCI
Provided drivers Microsoft Windows 98, 2000, Me, XP
Weight 40 g
LED Power, Activity
Operating Environment Operating temperature: 0 to 55 degrees C, 32 to 131 degrees F
Encryption 40-bit (also called 64-bit) and 128-bit WEP data encryption
![](/img.php?id=352059&img=bg30.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
A-2 Technical Specifications
![](/img.php?id=352059&img=bg31.png)
Wireless Networking Basics B-1
Appendix B
Wireless Networking Basics
This chapter provides an overview of Wireless networking.
Wireless Networking Overview
The WAG311 Wireless PCI Adapter conforms to the Institute of Electrical and Electronics
Engineers (IEEE) 802.11b standard for wireless LANs (WLANs) and a product update will bring
the WAG311 into conformance to the 802.11g standard when it is ratified. On an 802.11b or g
wireless link, data is encoded using direct-sequence spread-spectrum (DSSS) technology and is
transmitted in the unlicensed radio spectrum at 2.5GHz. The maximum data rate for the 802.11b
wireless link is 11 Mbps, but it will automatically back down from 11 Mbps to 5.5, 2, and 1 Mbps
when the radio signal is weak or when interference is detected. The 802.11g auto rate sensing rates
are 1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, and 54 Mbps. Likewise, the 802.11a wireless link offers a
maximum data rate of 54 Mbps, but will automatically back down to rates 48, 36, 24, 18, 12, 9,
and 6 Mbps.
The 802.11 standard is also called Wireless Ethernet or Wi-Fi by the Wireless Ethernet
Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standard group promoting
interoperability among 802.11 devices. The 802.11 standard offers two methods for configuring a
wireless network - ad hoc and infrastructure.
Infrastructure Mode
With a wireless Access Point, you can operate the wireless LAN in the infrastructure mode. This
mode provides wireless connectivity to multiple wireless network devices within a fixed range or
area of coverage, interacting with wireless nodes via an antenna.
In the infrastructure mode, the wireless access point converts airwave data into wired Ethernet
data, acting as a bridge between the wired LAN and wireless clients. Connecting multiple Access
Points via a wired Ethernet backbone can further extend the wireless network coverage. As a
mobile computing device moves out of the range of one access point, it moves into the range of
another. As a result, wireless clients can freely roam from one Access Point domain to another and
still maintain seamless network connection.
![](/img.php?id=352059&img=bg32.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
B-2 Wireless Networking Basics
Ad Hoc Mode (Peer-to-Peer Workgroup)
In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed
points to the network - each node can generally communicate with any other node. There is no
Access Point involved in this configuration. This mode enables you to quickly set up a small
wireless workgroup and allows workgroup members to exchange data or share printers as
supported by Microsoft networking in the various Windows operating systems. Some vendors also
refer to ad hoc networking as peer-to-peer group networking.
In this configuration, network packets are directly sent and received by the intended transmitting
and receiving stations. As long as the stations are within range of one another, this is the easiest
and least expensive way to set up a wireless network.
Network Name: Extended Service Set Identification (ESSID)
The Extended Service Set Identification (ESSID) is one of two types of Service Set Identification
(SSID). In an ad hoc wireless network with no access points, the Basic Service Set Identification
(BSSID) is used. In an infrastructure wireless network that includes an access point, the ESSID is
used, but may still be referred to as SSID.
An SSID is a thirty-two character (maximum) alphanumeric key identifying the name of the
wireless local area network. Some vendors refer to the SSID as network name. For the wireless
devices in a network to communicate with each other, all devices must be configured with the
same SSID.
The ESSID is usually broadcast in the air from an access point. The wireless station sometimes can
be configured with the ESSID ANY. This means the wireless station will try to associate with
whichever access point has the stronger radio frequency (RF) signal, providing that both the access
point and wireless station use Open System authentication.
Authentication and WEP Data Encryption
The absence of a physical connection between nodes makes the wireless links vulnerable to
eavesdropping and information theft. To provide a certain level of security, the IEEE 802.11
standard has defined these two types of authentication methods:
•Open System. With Open System authentication, a wireless PC can join any network and
receive any messages that are not encrypted.
![](/img.php?id=352059&img=bg33.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Wireless Networking Basics B-3
•Shared Key. With Shared Key authentication, only those PCs that possess the correct
authentication key can join the network. By default, IEEE 802.11 wireless devices operate in
an Open System network.
Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured
to operate in Shared Key authentication mode.
802.11 Authentication
The 802.11 standard defines several services that govern how two 802.11 devices communicate.
The following events must occur before an 802.11 Station can communicate with an Ethernet
network through an access point such as the one built in to the WAG311:
1. Turn on the wireless station.
2. The station listens for messages from any access points that are in range.
3. The station finds a message from an access point that has a matching SSID.
4. The station sends an authentication request to the access point.
5. The access point authenticates the station.
6. The station sends an association request to the access point.
7. The access point associates with the station.
8. The station can now communicate with the Ethernet network through the access point.
An access point must authenticate a station before the station can associate with the access point or
communicate with the network. The IEEE 802.11 standard defines two types of authentication:
Open System and Shared Key.
• Open System Authentication allows any device to join the network, assuming that the device
SSID matches the access point SSID. Alternatively, the device can use the “ANY” SSID
option to associate with any available Access Point within range, regardless of its SSID.
• Shared Key Authentication requires that the station and the access point have the same WEP
Key to authenticate. These two authentication procedures are described below.
Open System Authentication
The following steps occur when two devices use Open System Authentication:
1. The station sends an authentication request to the access point.
![](/img.php?id=352059&img=bg34.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
B-4 Wireless Networking Basics
2. The access point authenticates the station.
3. The station associates with the access point and joins the network.
This process is illustrated in below.
Figure B-1: Open system authentication
Shared Key Authentication
The following steps occur when two devices use Shared Key Authentication:
1. The station sends an authentication request to the access point.
2. The access point sends challenge text to the station.
3. The station uses its configured 64-bit or 128-bit default key to encrypt the challenge text, and
sends the encrypted text to the access point.
4. The access point decrypts the encrypted text using its configured WEP Key that corresponds
to the station’s default key. The access point compares the decrypted text with the original
challenge text. If the decrypted text matches the original challenge text, then the access point
and the station share the same WEP Key and the access point authenticates the station.
5. The station connects to the network.
If the decrypted text does not match the original challenge text (i.e., the access point and station do
not share the same WEP Key), then the access point will refuse to authenticate the station and the
station will be unable to communicate with either the 802.11 network or Ethernet network.
This process is illustrated in below.
INTERNET LOCAL
ACT
12345678
LNK
LNK/ACT
100
Cable/DSL ProSafeWirelessVPN Security Firewall
MODEL FVM318
PWR TEST
WLAN
Enable
Access Point (AP)
1) Authentication request sent to AP
2) AP authenticates
3) Client connects to network
Open System
Authentication Steps
Cable or
DLS modem
Client
attempting
to connect
![](/img.php?id=352059&img=bg35.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Wireless Networking Basics B-5
Figure B-2: Shared key authentication
Overview of WEP Parameters
Before enabling WEP on an 802.11 network, you must first consider what type of encryption you
require and the key size you want to use. Typically, there are three WEP Encryption options
available for 802.11 products:
1. Do Not Use WEP: The 802.11 network does not encrypt data. For authentication purposes, the
network uses Open System Authentication.
2. Use WEP for Encryption: A transmitting 802.11 device encrypts the data portion of every
packet it sends using a configured WEP Key. The receiving device decrypts the data using the
same WEP Key. For authentication purposes, the network uses Open System Authentication.
3. Use WEP for Authentication and Encryption: A transmitting 802.11 device encrypts the data
portion of every packet it sends using a configured WEP Key. The receiving device decrypts the
data using the same WEP Key. For authentication purposes, the wireless network uses Shared Key
Authentication.
Note: Some 802.11 access points also support Use WEP for Authentication Only (Shared Key
Authentication without data encryption).
INTERNET LOCAL
ACT
12345678
LNK
LNK/ACT
100
Cable/DSL ProSafeWirelessVPN Security Firewall
MODEL FVM318
PWR TEST
WLAN
Enable
Access Point1) Authentication
request sent to AP
2) AP sends challenge text
3) Client encrypts
challenge text and
sends it back to AP
4) AP decrypts, and if correct,
authenticates client
5) Client connects to network
Shared Key
Authentication Steps
Cable or
DLS modem
Client
attempting
to connect
![](/img.php?id=352059&img=bg36.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
B-6 Wireless Networking Basics
Key Size
The IEEE 802.11 standard supports two types of WEP encryption: 40-bit and 128-bit.
The 64-bit WEP data encryption method, allows for a five-character (40-bit) input. Additionally,
24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. (The 24
factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all
data transmitted via the wireless interface. Some vendors refer to the 64-bit WEP data encryption
as 40-bit WEP data encryption since the user-configurable portion of the encryption key is 40 bits
wide.
The 128-bit WEP data encryption method consists of 104 user-configurable bits. Similar to the
forty-bit WEP data encryption method, the remaining 24 bits are factory set and not user
configurable. Some vendors allow passphrases to be entered instead of the cryptic hexadecimal
characters to ease encryption key entry.
128-bit encryption is stronger than 40-bit encryption, but 128-bit encryption may not be available
outside of the United States due to U.S. export regulations.
In NETGEAR’s 802.11a solutions, there are three shared key methods implemented: the standards
based 40-bit and 128-bit WEP data encryption; and an extended 152-bit WEP data encryption.
When configured for 40-bit encryption, 802.11 products typically support up to four WEP Keys.
Each 40-bit WEP Key is expressed as 5 sets of two hexadecimal digits (0-9 and A-F). For
example, “12 34 56 78 90” is a 40-bit WEP Key.
When configured for 128-bit encryption, 802.11 products typically support four WEP Keys but
some manufacturers support only one 128-bit key. The 128-bit WEP Key is expressed as 13 sets of
two hexadecimal digits (0-9 and A-F). For example, “12 34 56 78 90 AB CD EF 12 34 56 78 90”
is a 128-bit WEP Key.
Table B-1: Encryption Key Sizes
Note: Typically, 802.11 access points can store up to four 128-bit WEP Keys but some 802.11
client adapters can only store one. Therefore, make sure that your 802.11 access and client
adapters configurations match.
Encryption Key Size # of Hexadecimal Digits Example of Hexadecimal Key Content
64-bit (24+40) 10 4C72F08AE1
128-bit (24+104) 26 4C72F08AE19D57A3FF6B260037
152-bit (24+128) 32 4C72F08AE19D57A3FF6B26003715DAC2
![](/img.php?id=352059&img=bg37.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Wireless Networking Basics B-7
WEP Configuration Options
The WEP settings must match on all 802.11 devices that are within the same wireless network as
identified by the SSID. In general, if your mobile clients will roam between access points, then all
of the 802.11 access points and all of the 802.11 client adapters on the network must have the same
WEP settings.
Note: Whatever keys you enter for an AP, you must also enter the same keys for the client adapter
in the same order. In other words, WEP key 1 on the AP must match WEP key 1 on the client
adapter, WEP key 2 on the AP must match WEP key 2 on the client adapter, etc.
Note: The AP and the client adapters can have different default WEP Keys as long as the keys are
in the same order. In other words, the AP can use WEP key 2 as its default key to transmit while a
client adapter can use WEP key 3 as its default key to transmit. The two devices will communicate
as long as the AP’s WEP key 2 is the same as the client’s WEP key 2 and the AP’s WEP key 3 is
the same as the client’s WEP key 3.
Wireless Channels
The wireless frequencies used by 802.11a and 802.11b/g networks are different. These channel
frequency options are discussed below.
802.11b/g Wireless Channels
IEEE 802.11b/g wireless nodes communicate with each other using radio frequency signals in the
ISM (Industrial, Scientific, and Medical) band between 2.4 GHz and 2.5 GHz. Neighboring
channels are 5 MHz apart. However, due to spread spectrum effect of the signals, a node sending
signals using a particular channel will utilize frequency spectrum 12.5 MHz above and below the
center channel frequency. As a result, two separate wireless networks using neighboring channels
(for example, channel 1 and channel 2) in the same general vicinity will interfere with each other.
Applying two channels that allow the maximum channel separation will decrease the amount of
channel cross-talk, and provide a noticeable performance increase over networks with minimal
channel separation.
![](/img.php?id=352059&img=bg38.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
B-8 Wireless Networking Basics
The radio frequency channels used in 802.11b/g networks are listed in Table D-2:
Note: The available channels supported by the wireless products in various countries are different.
For example, Channels 1 to 11 are supported in the U.S. and Canada, and Channels 1 to 13 are
supported in Europe and Australia.
The preferred channel separation between the channels in neighboring wireless networks is 25
MHz (5 channels). This means that you can apply up to three different channels within your
wireless network. There are only 11 usable wireless channels in the United States. It is
recommended that you start using channel 1 and grow to use channel 6, and 11 when necessary, as
these three channels do not overlap.
802.11a Legal Power Output and Wireless Channels
IEEE 802.11a utilizes 300 MHz of bandwidth in the 5 GHz Unlicensed National Information
Infrastructure (U-NII) band. Though the lower 200 MHz is physically contiguous, the FCC has
divided the total 300 MHz into three distinct domains, each with a different legal maximum power
output. Below is a table of summary for different regulatory domains.
Table B-2: 802.11b/g Radio Frequency Channels
Channel Center Frequency Frequency Spread
1 2412 MHz 2399.5 MHz - 2424.5 MHz
2 2417 MHz 2404.5 MHz - 2429.5 MHz
3 2422 MHz 2409.5 MHz - 2434.5 MHz
4 2427 MHz 2414.5 MHz - 2439.5 MHz
5 2432 MHz 2419.5 MHz - 2444.5 MHz
6 2437 MHz 2424.5 MHz - 2449.5 MHz
7 2442 MHz 2429.5 MHz - 2454.5 MHz
8 2447 MHz 2434.5 MHz - 2459.5 MHz
9 2452 MHz 2439.5 MHz - 2464.5 MHz
10 2457 MHz 2444.5 MHz - 2469.5 MHz
11 2462 MHz 2449.5 MHz - 2474.5 MHz
12 2467 MHz 2454.5 MHz - 2479.5 MHz
13 2472 MHz 2459.5 MHz - 2484.5 MHz
![](/img.php?id=352059&img=bg39.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Wireless Networking Basics B-9
Table B-3: 802.11a Radio Frequency Channels
Note: Please check your local Authority for updated information on the available frequency and
maximum power output.
IEEE 802.11a uses Orthogonal Frequency Division Multiplexing (OFDM), a new encoding
scheme that offers certain benefits over a spread spectrum in channel availability and data rate.
The 802.11a uses OFDM to define a total of 8 non-overlapping 200 MHz channels across the 2
lower bands; each of these is divided into 52 sub carriers and each carrier is approximately 300
KHz wide.
Figure B-3: IEEE 802.11a Channel Allocations
The WAG311 user can use thirteen channels in non-turbo mode.
Table B-4: 802.11a Turbo Mode Off Radio Frequency Channels
U-NII Band Low Middle High
Frequency (GHz) 5.15 – 5.25 5.25 – 5.35 5.725 – 5.825
Max. Power Output 50 mW for US
200 mW for
Canada, Europe,
and Australia
250 mW for US
200 mW for Europe and Australia
1 W for Canada
1 W for US and Australia
4 W for Canada
25 mW for Europe
Turbo Mode OFF
![](/img.php?id=352059&img=bg3a.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
B-10 Wireless Networking Basics
The WAG311 user can use five channels in turbo mode.
The available channels supported by the wireless products in various countries are different.
Channel Frequency
36
40
44
48
52
56
60
64
149 5.745 GHz
153 5.765 GHz
157 5.785 GHz
161 5.805 GHz
165 5.825 GHz
Turbo Mode ON
Channel Frequency
42 5.21 GHz
50 5.25 GHz
58 5.29 GHz
152 5.76 GHz
160 5.8 GHz
![](/img.php?id=352059&img=bg3b.png)
Preparing Your PCs for Network Access C-1
Appendix C
Preparing Your PCs for Network Access
This appendix describes how to prepare your PCs to connect to the Internet through the
NETGEAR 54 Mbps Wireless PCI Adapter WAG311.
For adding file and print sharing to your network, please consult the Windows help information
included with the version of Windows installed on each computer on your network.
Preparing Your Computers for TCP/IP Networking
Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/
Internet Protocol). Each computer on your network must have TCP/IP installed and selected as its
networking protocol. If a Network Interface Card (NIC) is already installed in your PC, then TCP/
IP is probably already installed as well.
Most operating systems include the software components you need for networking with TCP/IP.
Windows 95 or later includes the software components for establishing a TCP/IP network.
In your TCP/IP network, each PC and the wireless access point must be assigned a unique IP
addresses. Each PC must also have certain other TCP/IP configuration information such as a
subnet mask (netmask), a domain name server (DNS) address, and a default gateway address. In
most cases, you should install TCP/IP so that the PC obtains its specific network configuration
information automatically from a DHCP server during startup.
Configuring Windows 98 and Me for TCP/IP Networking
As part of the PC preparation process, you may need to install and configure
TCP/IP on your PC. Before starting, locate your Windows CD; you may need to insert it during the
TCP/IP installation process.
Install or Verify Windows Networking Components
To install or verify the necessary components for IP networking:
![](/img.php?id=352059&img=bg3c.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
C-2 Preparing Your PCs for Network Access
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network icon.
The Network window opens, which displays a list of installed components:
You must have an Ethernet adapter or an WAG311, the TCP/IP protocol, and the Client for
Microsoft Networks.
If you need to add TCP/IP:
a. Click the Add button.
b. Select Protocol, and then click Add.
c. Select Microsoft.
d. Select TCP/IP, and then click OK.
If you need to add the Client for Microsoft Networks:
a. Click the Add button.
b. Select Client, and then click Add.
c. Select Microsoft.
Note: It is not necessary to remove any other network components shown in the
Network window in order to install the adapter, TCP/IP, or Client for Microsoft
Networks.
![](/img.php?id=352059&img=bg3d.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Preparing Your PCs for Network Access C-3
d. Select Client for Microsoft Networks, and then click OK.
If you need to add File and Print Sharing for Microsoft Networks:
a. Click the Add button.
b. Select Client, and then click Add.
c. Select Microsoft.
d. Select File and Print Sharing for Microsoft Networks, and then click OK.
3. Restart your PC for the changes to take effect.
Enabling DHCP to Automatically Configure TCP/IP Settings
After the TCP/IP protocol components are installed, each PC must be assigned specific
information about itself and resources that are available on its network. The simplest way to
configure this information is to allow the PC to obtain the information from a DHCP server in the
network.
You will find there are many similarities in the procedures for different Windows systems
when using DHCP to configure TCP/IP.
The following steps will walk you through the configuration process for each of these
versions of Windows.
Locate your Network Neighborhood icon.
• If the Network Neighborhood icon is on the Windows desktop, position your
mouse pointer over it and right-click your mouse button.
• If the icon is not on the desktop,
• Click Start on the task bar located at the bottom left of the window.
• Choose Settings, and then Control Panel.
• Locate the Network Neighborhood icon and click on it. This will open
the Network panel as shown below.
![](/img.php?id=352059&img=bg3e.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
C-4 Preparing Your PCs for Network Access
Verify the following settings as shown:
• Client for Microsoft Network exists
• Ethernet adapter is present
• TCP/IP is present
•Primary Network Logon is set to
Windows logon
Click on the Properties button. The
following TCP/IP Properties window will
display.
![](/img.php?id=352059&img=bg3f.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Preparing Your PCs for Network Access C-5
Selecting the Internet Access Method
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Internet Options icon.
3. Select “I want to set up my Internet connection manually” or “I want to connect through a
Local Area Network” and click Next.
4. Select “I want to connect through a Local Area Network” and click Next.
5. Uncheck all boxes in the LAN Internet Configuration screen and click Next.
6. Proceed to the end of the Wizard.
Verifying TCP/IP Properties
After your PC is configured and has rebooted, you can check the TCP/IP configuration using the
utility winipcfg.exe:
1. On the Windows taskbar, click the Start button, and then click Run.
By default, the IP Address tab is open on
this window.
• Verify the following:
Obtain an IP address automatically is
selected. If not selected, click in the
radio button to the left of it to select it.
This setting is required to enable the
DHCP server to automatically assign an
IP address.
• Click OK to continue.
Restart the PC.
Repeat these steps for each PC with this
version of Windows on your network.
![](/img.php?id=352059&img=bg40.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
C-6 Preparing Your PCs for Network Access
2. Type winipcfg, and then click OK.
The IP Configuration window opens, which lists (among other things), your IP address, subnet
mask, and default gateway.
3. From the drop-down box, select your Ethernet adapter.
The window is updated to show your settings, which should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends for connecting through a
router or gateway:
• The IP address is between 192.168.0.2 and 192.168.0.254
• The subnet mask is 255.255.255.0
• The default gateway is 192.168.0.1
Configuring Windows 2000 or XP for TCP/IP Networking
As part of the PC preparation process, you may need to install and configure
TCP/IP on each networked PC. Before starting, locate your Windows CD; you may need to insert
it during the TCP/IP installation process.
Install or Verify Windows Networking Components
To install or verify the necessary components for IP networking:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dial-up Connections icon.
3. If an Ethernet adapter is present in your PC, you should see an entry for Local Area
Connection. Double-click that entry.
4. Select Properties.
5. Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If
not, select Install and add them.
6. Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address
automatically is selected.
7. Click OK and close all Network and Dial-up Connections windows.
8. Then, restart your PC.
![](/img.php?id=352059&img=bg41.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Preparing Your PCs for Network Access C-7
DHCP Configuration of TCP/IP in Windows XP or 2000
You will find there are many similarities in the procedures for different Windows systems when
using DHCP to configure TCP/IP.
The following steps will walk you through the configuration process for each of these versions of
Windows.
DHCP Configuration of TCP/IP in Windows XP
Locate your Network Neighborhood icon.
• Select Control Panel from the Windows XP Start Menu.
• Select the Network Connections icon on the Control Panel. This will take you to the next
step.
Now the Network Connection window
displays.
The Connections List that shows all the
network connections set up on the PC,
located to the right of the window.
• Right-click on the Connection with the
wireless icon and choose Status.
![](/img.php?id=352059&img=bg42.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
C-8 Preparing Your PCs for Network Access
Now you should be at the Local Area
Network Connection Status window. This
box displays the connection status,
duration, speed, and activity statistics.
Administrator logon access rights are
needed to use this window.
• Click the Properties button to view
details about the connection.
The TCP/IP details are presented on the
Support tab page.
• Select Internet Protocol, and click
Properties to view the configuration
information.
![](/img.php?id=352059&img=bg43.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Preparing Your PCs for Network Access C-9
DHCP Configuration of TCP/IP in Windows 2000
After you install a network card, TCP/IP for Windows 2000 is configured and set to DHCP
without your having to configure it. However, if there are problems, following the steps below to
configure TCP/IP with DHCP for Windows 2000.
Verify that Obtain an IP address
automatically radio button is selected and
that the Obtain DNS server address
automatically radio button is selected.
• Click the OK button.
This completes the DHCP configuration in
Windows XP.
Repeat these steps for each PC with this
version of Windows on your network.
Click on the My Network Places icon on the Windows desktop. This will bring up a window
called Network and Dial-up Connections.
• Right click on Local Area Connection and select Properties.
![](/img.php?id=352059&img=bg44.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
C-10 Preparing Your PCs for Network Access
The Local Area Connection Properties
dialog box appears. Verify that you have
the correct Ethernet card selected in the
Connect using: box and that the following
two items are displayed and selected in the
box of “Components checked are used by
this connection:”
• Client for Microsoft Networks and
• Internet Protocol (TCP/IP)
Click OK.
With Internet Protocol (TCP/IP) selected,
click on Properties to open the Internet
Protocol (TCP/IP) Properties dialogue
box. Verify that
•Obtain an IP address
automatically is selected.
•Obtain DNS server address
automatically is selected.
Click OK to return to Local Area
Connection Properties. Click OK again to
complete the configuration process.
Restart the PC. Repeat these steps for each
PC with this version of Windows on your
network.
![](/img.php?id=352059&img=bg45.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Preparing Your PCs for Network Access C-11
Verifying TCP/IP Properties for Windows XP or 2000
To check your PC’s TCP/IP configuration:
1. On the Windows taskbar, click the Start button, and then click Run.
The Run window opens.
2. Type cmd and then click OK.
A command window opens
3. Type ipconfig /all
Your IP Configuration information will be listed, and should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends for connecting through a
router or gateway:
• The IP address is between 192.168.0.2 and 192.168.0.254
• The subnet mask is 255.255.255.0
• The default gateway is 192.168.0.1
4. Type exit
![](/img.php?id=352059&img=bg46.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
C-12 Preparing Your PCs for Network Access
![](/img.php?id=352059&img=bg47.png)
Glossary 1
Glossary
List of Glossary Terms
Use the list below to find definitions for technical terms used in this manual.
10BASE-T
IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.
100BASE-Tx
IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.
802.11a
IEEE specification for wireless networking at 54 Mbps operating in unlicensed radio bands over 5GHz.
802.11b
IEEE specification for wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS)
technology and operating in the unlicensed radio spectrum at 2.4GHz.
802.11g
A soon to be ratified IEEE specification for wireless networking at 54 Mbps using direct-sequence
spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz. 802.11g is
backwards compatible with 802.11b.
ADSL
Short for asymmetric digital subscriber line, a technology that allows data to be sent over existing copper
telephone lines at data rates of from 1.5 to 9 Mbps when receiving data (known as the downstream rate) and
from 16 to 640 Kbps when sending data (known as the upstream rate).
ADSL requires a special ADSL modem. ADSL is growing in popularity as more areas around the world
gain access.
DHCP
An Ethernet protocol specifying how a centralized DHCP server can assign network configuration
information to multiple DHCP clients. The assigned information includes IP addresses, DNS addresses, and
gateway (router) addresses.
DNS
Short for Domain Name System (or Service), an Internet service that translates domain names into IP
addresses.
![](/img.php?id=352059&img=bg48.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
2Glossary
Because domain names are alphabetic, they're easier to remember. The Internet however, is really based on
IP addresses. Every time you use a domain name, therefore, a DNS service must translate the name into the
corresponding IP address. For example, the domain name www.example.com might translate to
198.105.232.4. The DNS system is, in fact, its own network. If one DNS server doesn't know how to
translate a particular domain name, it asks another one, and so on, until the correct IP address is returned.
Domain Name
A descriptive name for an address or group of addresses on the Internet. Domain names are of the form of a
registered entity name plus one of a number of predefined top level suffixes such as .com, .edu, .uk, etc. For
example, in the address mail.NETGEAR.com, mail is a server name and NETGEAR.com is the domain.
DSL
Short for digital subscriber line, but is commonly used in reference to the asymmetric version of this
technology (ADSL) that allows data to be sent over existing copper telephone lines at data rates of from 1.5
to 9 Mbps when receiving data (known as the downstream rate) and from 16 to 640 Kbps when sending data
(known as the upstream rate).
ADSL requires a special ADSL modem. ADSL is growing in popularity as more areas around the world
gain access.
Dynamic Host Configuration Protocol
DHCP. An Ethernet protocol specifying how a centralized DHCP server can assign network configuration
information to multiple DHCP clients. The assigned information includes IP addresses, DNS addresses, and
gateway (router) addresses.
ESSID
The Extended Service Set Identification (ESSID) is a thirty-two character (maximum) alphanumeric key
identifying the wireless local area network.
Gateway
A local device, usually a router, that connects hosts on a local network to other networks.
IETF
Internet Engineering Task Force. Working groups of the IETF propose standard protocols and procedures for
the Internet, which are published as RFCs (Request for Comment) at www.ietf.org.
An open international community of network designers, operators, vendors, and researchers concerned with
the evolution of the Internet architecture and the smooth operation of the Internet.
IP
Internet Protocol is the main internetworking protocol used in the Internet. Used in conjunction with the
Transfer Control Protocol (TCP) to form TCP/IP.
IP Address
A four-byte number uniquely defining each host on the Internet, usually written in dotted-decimal notation
with periods separating the bytes (for example, 134.177.244.57).
![](/img.php?id=352059&img=bg49.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Glossary 3
Ranges of addresses are assigned by Internic, an organization formed for this purpose.
IPX
Short for Internetwork Packet Exchange, a networking protocol used by the Novell NetWare operating
systems.
Like UDP/IP, IPX is a datagram protocol used for connectionless communications. Higher-level protocols,
such as SPX and NCP, are used for additional error recovery services.
ISP
Internet service provider.
Internet Protocol
The main internetworking protocol used in the Internet. Used in conjunction with the Transfer Control
Protocol (TCP) to form TCP/IP.
LAN
A communications network serving users within a limited area, such as one floor of a building.
local area network
LAN. A communications network serving users within a limited area, such as one floor of a building.
A LAN typically connects multiple personal computers and shared network devices such as storage and
printers. Although many technologies exist to implement a LAN, Ethernet is the most common for
connecting personal computers.
MAC address
The Media Access Control address is a unique 48-bit hardware address assigned to every network interface
card. Usually written in the form 01:23:45:67:89:ab.
Mbps
Megabits per second.
NetBIOS
The Network Basic Input Output System is an application programming interface (API) for sharing services
and information on local-area networks (LANs).
Provides for communication between stations of a network where each station is given a name. These names
are alphanumeric names, up to 16 characters in length.
Network Address Translation
NAT. A technique by which several hosts share a single IP address for access to the Internet.
NIC
Network Interface Card. An adapter in a computer which provides connectivity to a network.
![](/img.php?id=352059&img=bg4a.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
4Glossary
packet
A block of information sent over a network. A packet typically contains a source and destination network
address, some protocol and length information, a block of data, and a checksum.
router
A device that forwards data between networks. An IP router forwards data based on IP source and
destination addresses.
Routing Information Protocol
RIP. A protocol in which routers periodically exchange information with one another so that they can
determine minimum distance paths between sources and destinations.
SSID
A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless
local area network. For the wireless devices in a network to communicate with each other, all devices must
be configured with the same SSID.
This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the
wireless Access Point and to the wireless network name. See also Wireless Network Name and ESSID.
Subnet Mask
A mask used to determine what subnet an IP address belongs to. Subnetting enables a network administrator
to further divide an IP address into two or more subnets.
TCP/IP
The main internetworking protocols used in the Internet. The Internet Protocol (IP) used in conjunction with
the Transfer Control Protocol (TCP) form TCP/IP.
WAN
A long distance link used to extend or connect remotely located local area networks. The Internet is a large
WAN.
WEB Proxy Server
A Web proxy server is a specialized HTTP server that allows clients access to the Internet from behind a
firewall.
The proxy server listens for requests from clients within the firewall and forwards these requests to remote
Internet servers outside the firewall. The proxy server reads responses from the external servers and then
sends them to internal client clients.
WEP
Wired Equivalent Privacy is a data encryption protocol for 802.11b wireless networks.
All wireless nodes and access points on the network are configured with a 64-bit or 128-bit Shared Key for
data encryption.
![](/img.php?id=352059&img=bg4b.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
Glossary 5
wide area network
WAN. A long distance link used to extend or connect remotely located local area networks. The Internet is a
large WAN.
Wi-Fi
A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility
Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among
802.11b devices.
Windows Internet Naming Service
WINS. Windows Internet Naming Service is a server process for resolving Windows-based computer names
to IP addresses.
If a remote network contains a WINS server, your Windows PCs can gather information from that WINS
server about its local hosts. This allows your PCs to browse that remote network using the Windows
Network Neighborhood feature.
WINS
WINS. Windows Internet Naming Service is a server process for resolving Windows-based computer names
to IP addresses.
Wireless Network Name (SSID)
Wireless Network Name (SSID) is the name assigned to a wireless network. This is the same as the SSID or
ESSID configuration parameter.
![](/img.php?id=352059&img=bg4c.png)
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WAG311
6Glossary
![](/img.php?id=352059&img=bg4d.png)
Index 1
Numerics
802.11b 1
A
ad-hoc mode 2
B
BSSID 2
E
ESSID 2
F
features 1
I
infrastructure mode 2
IP networking
for Windows 1, 6
O
Open System authentication 2
S
Shared Key authentication 2
SSID 3, 2
T
TCP/IP properties
verifying for Windows 5
W
WEP 3, 8, 2
Wi-Fi 1
Windows, configuring for IP routing 1, 6
winipcfg utility 5
Wired Equivalent Privacy. See WEP
Wireless Ethernet 1
wireless network name 3
Index