Northfield Telecommunications d b a Advanced Wireless Communications HD-1000 TWO-WAY RADIO User Manual 1
Northfield Telecommunications, Inc. d/b/a Advanced Wireless Communications TWO-WAY RADIO 1
Users Manual
HD-1000 GENERAL/概述 INTRODUCTION SCOPE OF THIS MANUAL 引言 本手册的范围 This manual is intended for use by experienced technicians familiar with similar types of commercial grade communications equipment. It contains all required service information for the equipment and is current as of the publication date.Changes which may occur after publication are covered by either Service Bulletins or Manual Revisions. These are issued as required. 本手册是提供给熟悉通信专业并且具有维修经验的技术人员 使用的。 它包括了维修该设备所 需要的全部资料和现行公布 的数据。在出版后可能发生变动,如果需要,可以使用《维修 通报》或《手册修订本》进行补充。 ORDERING REPLACEMENT PARTS 替换零件的订购 When ordering replacement parts or equipment information, the full part identification number should be included.This applies to all parts: components, kits, or chassis. If the part number is not known, include the chassis or kit number of which it is a part, and a sufficient description of the required component for proper identification. 当订购替换零件或设备信息时,应注明完整的零件识别号码。 所有的零件均有识别号码:元件、组件或机壳。如果不知道 零件的号码,为了正确地识别,必须注明此元件所属的机壳 或组件的号码,并对元件进行充分的说明。 PERSONAL SAFETY 个人安全 为了个人的安全,请注意下列事项: The following precautions are recommended for personal safety: • DO NOT transmit until all RF connectors are verified secure and any open connectors are properly terminated. • SHUT OFF and DO NOT operate this equipment near electrical blasting caps or in an explosive •This equipment should be serviced by a qualified technician only. • 在没有认真核实所有射频插头之前或有任何一个打开的插头 没有连接到响应端子上的情况下,均不要发射。 • 在电爆管附近或在易燃性气体环境中,必须关掉电源,不要 操作本设备 • 本设备只应该由有资格的技术人员来维修。 SERVICE 维修服务 This radio is designed for easy servicing. Refer to the schematic diagrams, printed circuit board views, and alignment procedures contained within. 为了便于维修本设备,建立了完整的维修服务体系,提供了 包括原理图、印刷线路图和调整步骤在内的资料供参考。 Number of channels RF Power Output 199 0.5W/1W 信道数量 199 射频输出功率 0.5W/1W 910 MODES 模式 USER MODE MODES PC MODE PC模式 用户模式 FUNCTION 模式类型 User mode For normal use. 用户模式 用于普通操作 PC mode Used for communication between the radio and a PC 计算机模式 Used for communication between the radio and a PC 功能 How to enter each mode PROCEDURE MODES User mode PC mode Power ON 模式类型 用户模式 操作步骤 打开电源开关 Receiver commands from PC 计算机模式 从计算机接收命令 PC MODE 计算机模式 Preface 前言 The HD-1000 transceiver can be programmed using a personal computer, A programming interface cable and programming software. The programming software can be used on an IBM PC or compatible. Fig-1 shows the setup of a PC for programming. 通过个人电脑,使用编程电缆和编程软件,对对讲机HD-1000 进行编程设置。图1表示一台IBM计算机的编程设置过程。 Caution: When removing or installing the programming cable,first switch off the radio power. Additionally, be sure to disable the VOX function, if 注意 当拔除或者插入编程电缆首先关闭对讲机电源。另外,确保声 控功能已关闭,如果声控被激活,可能有时会开启连接噪音。 it’s enabled, as it can sometimes activate from connection noise. Connection procedure 1. Connect the HD-1000 to the personal Computer using the interface cable. 连接步骤 1.使用接口电缆将HD-1000与个人电脑连接。 2.当电源开关打开,可以进入用户模式。 2. When the POWER is switched ON, you can enter user mode. Programming software description 编程软件说明 The software allows a user to program the HD-1000 radios via the programming interface cable. 该软件允许用户经由编程接口电缆对HD-1000进行编程设定。 • Programming with IBM PC If data is transferred to the transceiver from a PC with the software, the destination data (basic radio information) for each set can be modified. 使用IBM计算机编程 如果从使用软件的IBM计算机将数据发送到手持机,设定的目的 数据(基本通信参数)均可被修改。 DISASSEMBLY FOR REPAIR/维修时拆卸部分 Separating the case assembly from the chassis 1. Remove the knob 1 and the round nut 2 2. Remove the six screws 3 and 4 3. Expand the right and left sides of the bottom of the case assembly, lift the chassis,and remove it from the case assembly 5. 4. Taking care not to cut the speaker lead 7,open the chassis and case assembly. Separating the chassis from the unit Remove the screws 8 and drop-out line, and lift the first unit off. 从底座上分离外壳 1.取下旋扭 1 和环形螺母 2 2.取下六颗螺钉 3 和 4 3.掀开外壳底部的左右两侧,取下底座,并外壳中取出 5 4.小心不要折断扬声器引线 7 ,拆下底座和外壳。 底座从主板上分离 取下螺钉 8 ,然后取下主板.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2009:05:19 14:13:18+08:00 Metadata Date : 2009:05:19 14:13:44+08:00 Creator Tool : Adobe Illustrator CS2 Format : application/pdf Title : 1 Creator : USER Document ID : uuid:4864606d-f705-4c48-bcd4-2149881a7dc5 Instance ID : uuid:467c343f-547f-45d4-b411-c2137dd9c35f Producer : Adobe Photoshop for Windows Has XFA : No Page Count : 6 Application Record Version : 2 By-line : USER Object Name : 1 X Resolution : 72 Y Resolution : 72 Orientation : Horizontal (normal) Resolution Unit : inches Software : Adobe Photoshop CS Windows Modify Date : 2007:12:06 19:01:55 Artist : USER Color Space : Uncalibrated Exif Image Width : 516 Exif Image Height : 776 Compression : JPEG (old-style) Thumbnail Offset : 318 Thumbnail Length : 0 For : User, - Bounding Box : -31 -33 499 761 Warning : IFD0 pointer references previous IFD0 directory IPTC Digest : 4cae19fc467be10a63fa352107fd34d8 Displayed Units X : inches Displayed Units Y : inches Print Style : Centered Print Position : 0 0 Print Scale : 1 Global Angle : 30 Global Altitude : 30 Copyright Flag : False URL List : Slices Group Name : 4 Num Slices : 1 Pixel Aspect Ratio : 1 Photoshop Thumbnail : (Binary data 4571 bytes, use -b option to extract) Has Real Merged Data : Yes Writer Name : Adobe Photoshop Reader Name : Adobe Photoshop CS Exif Byte Order : Big-endian (Motorola, MM) Creator Version : 12 Container Version : 9 Author : USEREXIF Metadata provided by EXIF.tools