Precyse Technologies SA91004005 Badge Tag V2 SA91/004005 User Manual Badge Tag V2 915MHz
Precyse Technologies Inc Badge Tag V2 SA91/004005 Badge Tag V2 915MHz
User Manual
Precyse Technologies 100 Ashford Center North Suite 360 Atlanta, GA 30338 Document No.:20121023-1 Revision: 1.2 Badge Tag V2 915MHz User Manual Release Date: 013/230/12 Prepared by: Yossi Nurok Distribution (Check all appropriate): [ ] Precyse Only [ ] Project Team Only [ ] Customer and Supplier Precyse Technologies, Inc. Date: 21 March 2013 Page 1 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Revision Record Rev. 1.0 1.1 1.2 Effective Date 23/01/13 10/03/13 21/03/13 Description Badge Tag V2 user manual initial release Correction for Frequency range 905-917.14MHz. Tag wearing instruction on p.7 Reference documents Doc # Description Precyse Technologies, Ltd.. Date: 21 March 2013 Page 2 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 TABLE OF CONTENTS Section/Title Page Introduction ...................................................................................................... 4 Regulatory Information/disclaimers .................................................................. 4 Product description .......................................................................................... 6 Badge Tag: ................................................................................................... 6 Technical Parameters ...................................................................................... 6 Models: ......................................................................................................... 6 Performance: ................................................................................................ 6 Communication: ............................................................................................ 6 Electrical: ...................................................................................................... 6 Environmental: .............................................................................................. 7 System test configuration ................................................................................. 7 SAT ............................................................................................................... 7 Tag wearing ..................................................................................................... 7 Theory of operation .......................................................................................... 8 iLocate system block diagram .......................................................................... 8 Precyse Technologies, Ltd.. Date: 21 March 2013 Page 3 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Introduction This document provides you with technical support information, and sources for additional product information. Regulatory Information/disclaimers Installation and use of this Wireless Radio device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The Manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, of the substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This document is confidential and proprietary. No part of this document may be reproduced, stored, or transmitted in any form or by any means without prior written permission from Precyse technologies Inc. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation." Precyse Technologies, Ltd.. Date: 21 March 2013 Page 4 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 The FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician. FCC Warning Modifications not expressly approved by the manufacturer could void the user authority to operate the equipment under FCC Rules. Precyse Technologies, Ltd.. Date: 21 March 2013 Page 5 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Product description Badge Tag: The SA Tag is used to track assets in real time. It is based on an RF transceiver and a microcontroller. It uses the Precyse N3 proprietary protocol which provides a 2 way, half duplex communication with the base station. The unit is powered by a 3 AA battery. Technical Parameters Models: E3-HuTag-AGPS Part number: SA91/004005 Performance: Read range: up to 1km. (Within line of sight) Write range: up to 1km. (Within line of sight) Read rate: 250Kbps. Write rate: 250Kbps. Communication: Frequency: 905-917.14MHz ISM within license free band Modulation: 2-FSK Channel bandwidth: 800KHz Number of channels: 16 ERP: Up to 17dBm, digitally controlled Communication protocol: N3. Transmission: Event base and on demand External interfaces: 1. 6 user buttons: 1-screen light, 2-find immediate location, 3-distress, 4-respond, 5-cancell message, 6-not used. The buttons are not used to increase transmission power in any way. 2. Buzzer 3. GPS receiver. Internal sensors: Motion, temperature sensors. Electrical: Power supply: 3.6Vdc. Precyse Technologies, Ltd.. Date: 21 March 2013 Page 6 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Environmental: Size: 57mm (L) x 17mm (W) x 105mm (H) Operating temperature: -20°C to +75°C Humidity: 90% non-condensing Weight: 145gr. (5 ounces) System test configuration SAT The unit tested was configured with all hardware options present. Since the unit, under its normal operation, does not transmit data periodically, for emissions measurements, the SAT was programmed with special test software to transmit packets continuously at 17dBm output power, duty cycle (67.7%) with power amplifier enabled for FCC test requirement only. Normal operation duty cycle, assuming worst case, one event per second is less than 0.5% (5mSec transmit time per 1 second). Tag wearing Badge Tag V2 should be worn on the waist belt with crocodile clip as shown in picture below. Precyse Technologies, Ltd.. Date: 21 March 2013 Page 7 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Theory of operation The SAT method of communication is synchronized event based reporting, the SAT spends most of its time in low power sleep mode. Event could be GPS location, motion start and stop, PBC found and which one. When an event happens, the SAT sends a report to the base station. In order to avoid packet collisions and associated detection methods, the system uses a synchronous protocol, that is, An SAT can transmit data only after receiving a synchronization signal from the base station. iLocate system block diagram PC Ethernet PBS PBC2 PBC1 TAG (SAT) Attached to assets PBC3 Precyse Technologies, Ltd.. Date: 21 March 2013 Page 8 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Unit definitions: Base station, referred to as PBS: A radio device that transmits data to and from the tag (SAT) to a personal computer (PC), also provides synchronization signal. The unit is powered by a DC power supply. Beacon, referred to as PBC: A radio device that defines a location. Location detection can be realized through one or more PBCs. The unit is powered by a DC power supply. Tag (SAT): A radio device that is used to track and monitor assets. It communicates with the PBS and can detect the PBC signals. Precyse Technologies, Ltd.. Date: 21 March 2013 Page 9 of 9
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 9 Language : en-US Tagged PDF : Yes Title : Badge Tag V2 915MHz Author : Yossi Nurok Subject : User Manual Creator : Microsoft® Word 2010 Create Date : 2013:03:21 13:33:11+02:00 Modify Date : 2013:03:21 13:33:11+02:00 Producer : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools