Remote Technologies RTI0300 Remote Control Transmitter User Manual T3 Operation Guide for Websit
Remote Technologies Inc Remote Control Transmitter T3 Operation Guide for Websit
Contents
- 1. Manual
- 2. Users Manual
Manual
![](/img.php?id=563899&img=bg1.png)
IR-PRO
Professional Infrared Code Capture System
T3
Universal System Controller
T3
Operation Guide
v1.0
i
FEDERAL COMMUNICATIONS COMMISSION NOTICE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC ID: MMURTI0300
CAN: 3166-RTI0300
![](/img.php?id=563899&img=bg3.png)
T3 Universal System Controller
ii
BATTERY DISPOSAL
For environmental reasons, your T3 universal system
controller uses “environmentally sound” Lithium-ion
rechargeable batteries. These batteries do not contain
any poisonous heavy metals that can damage the
environment.
In the interest of recycling, please do not dispose of these batteries
in the household waste at the end of their useful life. Instead,
dispose of them at an appropriate collection site.
SAFETY SUGGESTIONS
Read Instructions. Read all safety and operating instructions
before operating the unit.
Heat. Keep the unit away from heat sources such as radiators,
heat registers, stoves, etc., including amplifiers that produce heat.
Power Sources. Connect the docking station only to the power
supply that was included with the unit. Recharge the battery only
with the docking station that was included with the unit.
Power Cord Protection. Route power supply cords so that they
are not likely to be walked on or pinched by items placed on or
against them, paying particular attention to the cords at power
receptacles and at the point at which they exit from the unit.
Nonuse Periods. Unplug the power supply from the outlet when
the unit is to be left unused for a long period.
Water and Moisture. Do not use the unit near water—for
example, near a sink, in a wet basement, near a swimming pool,
near an open window, etc.
Object and Liquid Entry. Do not allow objects to fall or liquids to
be spilled into the enclosure through openings.
Cleaning. The unit should be cleaned only as recommended in the
operating guide.
Li-ion
iii
Servicing. Do not attempt any service beyond that described in
the operating guide. Refer all other service needs to qualified
service personnel.
Damage Requiring Service. The unit should be serviced by
qualified service personnel when:
• The power supply cord or the plug has been damaged.
• Objects have fallen or liquid has been spilled into the unit.
• The unit does not appear to operate normally or exhibits a
marked change in performance.
LIMITED WARRANTY
Remote Technologies Incorporated warrants its products for a
period of one (1) year from the date of purchase from Remote
Technologies Incorporated or an authorized Remote Technologies
Incorporated distributor.
This warranty may be enforced by the original purchaser and
subsequent owners during the warranty period, so long as the
original dated sales receipt or other proof of warranty coverage is
presented when warranty service is required.
Except as specified below, this warranty covers all defects in
material and workmanship in this product. The following are not
covered by the warranty:
Damage resulting from:
1. Accident, misuse, abuse, or neglect.
2. Failure to follow instructions contained in this Guide.
3. Repair or attempted repair by anyone other than Remote
Technologies Incorporated.
4. Causes other than product defects, including lack of skill,
competence or experience of user.
5. Shipment of this product (claims must be made to carrier).
6. Being altered or which the serial number has been defaced,
modified or removed.
![](/img.php?id=563899&img=bg5.png)
T3 Universal System Controller
iv
Remote Technologies Incorporated is not liable for any damages
caused by its products or for its failure of its products to perform,
including any lost profits, lost savings, incidental damages, or
consequential damages.
Remote Technologies Incorporated is not liable for damages based
upon inconvenience, loss of use of the product, loss of time,
interrupted operation, commercial loss, any claim made by a third
party or made by you for a third party.
Remote Technologies Incorporated’s liability for any defective
product is limited to repair or replacement of the product, at our
option.
If your T3 needs service, please contact Remote Technologies
Incorporated by telephone, fax or e-mail for return information.
Please do not return products to RTI without return
authorization.
DISCLAIMER
All rights are reserved. No part of this document may be
photocopied, reproduced, or translated without the prior written
notice of Remote Technologies Incorporated.
The information contained in this document is subject to change
without notice. Remote Technologies Incorporated shall not be
liable for errors or omissions contained herein or for consequential
damages in connection with the furnishing, performance, or use of
this guide.
Microsoft and Windows are registered trademarks of Microsoft
Corporation. Other brands and their products are trademarks or
registered trademarks of their respective holders.
T3, It’s Under Control, TheaterTouch, and the RTI logo are
trademarks of Remote Technologies Incorporated.
v
Contents
Federal Communications Commission Notice ---------------------- i
Battery Disposal ----------------------------------------------------------- ii
Safety Suggestions -------------------------------------------------------- ii
Limited Warranty -------------------------------------------------------- iii
Disclaimer-------------------------------------------------------------------iv
Contents------------------------------------------------------------------------ v
Chapter 1. Welcome----------------------------------------------------------1
Compatibility Note---------------------------------------------------------1
Unpacking and Inspection -----------------------------------------------2
Product Contents -----------------------------------------------------------2
Software Requirements ---------------------------------------------------2
Chapter 2. Introduction -----------------------------------------------------3
Features-----------------------------------------------------------------------3
Important Notes ------------------------------------------------------------4
Cleaning ----------------------------------------------------------------------5
Battery and Docking Station ---------------------------------------------5
Getting Started --------------------------------------------------------------7
Remote Reference ----------------------------------------------------------8
Docking Station Reference --------------------------------------------- 10
Chapter 3. Operation------------------------------------------------------- 11
The Touchscreen Display----------------------------------------------- 11
The Control Panel Page ------------------------------------------------- 12
Backlight Level--------------------------------------------------------- 13
Time Out ---------------------------------------------------------------- 15
Tilt Switch--------------------------------------------------------------- 16
![](/img.php?id=563899&img=bg7.png)
T3 Universal System Controller
vi
Battery ------------------------------------------------------------------- 17
Sound -------------------------------------------------------------------- 18
Calibrate Touchscreen------------------------------------------------ 19
Programming The T3---------------------------------------------------- 20
Chapter 4. Troubleshooting---------------------------------------------- 21
Display is Dim, Blank or Unreadable-------------------------------- 21
USB Communication Problems --------------------------------------- 21
IR Code Problems -------------------------------------------------------- 22
Chapter 5. Service and Support----------------------------------------- 23
Updates and New Products-------------------------------------------- 23
Contacting Remote Technologies Incorporated ------------------- 23
RTI Technical Support -------------------------------------------------- 23
Specifications---------------------------------------------------------------- 25
1
Chapter 1. Welcome
Thank you for purchasing the T3 universal system controller. The
T3 combines the power and flexibility of a graphic LCD
touchscreen with an ergonomic design that permits effortless one-
handed operation. This design overcomes the need for a
compromise between form and function. Sleek and perfectly
balanced, the T3 is infinitely flexible and expandable.
The T3 takes complete control of the home theater, replacing all
other remotes. It features an intuitive, easy to read color LCD that
can display custom buttons, text, graphics, symbols, and icons. In
addition to the backlit display, 16 “Hard” keypad buttons allow
easy access to frequently used functions.
Programming is easy and convenient thanks to the Windows®
based TheaterTouch Designer™ software. Because RTI’s remote
control products are sold only through professional
installers/programmers, and never directly to consumers, it is our
philosophy to not incorporate programming capability directly
into our products. Instead, we are committed to providing our
dealers with the hardware and software tools that allow them to
create re-usable programming databases and templates in the
most efficient and reliable way possible.
The T3 is capable of both infrared and radio frequency output.
Optional RF receivers are available for transmission through walls
and cabinets. The RF receivers connect to an RTI control system
for the ultimate in control reliability and flexibility. RTI control
systems provide many advanced features such as IR routing, local
macro execution, power sensing, and RS-232 control.
COMPATIBILITY NOTE
The T3 and TheaterTouch Designer software are compatible with
infrared (IR) commands with carrier frequencies between 15KhZ
and 460KhZ, as well as those commands that do not use a carrier.
This covers virtually all of the remotes that exist to date.
![](/img.php?id=563899&img=bg9.png)
T3 Universal System Controller
2
UNPACKING AND INSPECTION
After unpacking your new T3 universal system controller, save all
of the packing materials in case you ever have to ship the unit.
Thoroughly inspect the T3 and packing materials for signs of
damage. Report any damage to the carrier immediately. Report
any equipment malfunctions to Remote Technologies
Incorporated or an authorized Remote Technologies Incorporated
distributor.
PRODUCT CONTENTS
Contents within the box include the following items:
One (1) T3 universal system controller
One (1) Docking station.
One (1) Universal power supply for docking station
One (1) Operation guide.
SOFTWARE REQUIREMENTS
The recommended minimum system requirements needed to run
the TheaterTouch Designer software are as follows:
Windows 98SE®, Windows ME®, Windows 2000®, Windows
XP® or later version.
A free USB port.
At least 64 Megabytes of RAM.
At least 100 Megabytes of free disk storage.
Screen resolution of 800x600 with 16-bit color.
A mouse is required.
Optional printer for printing reports.
3
Chapter 2. Introduction
FEATURES
The T3 provides superior quality and reliability as well as these
specific features:
A replacement for all of the remote controls in a home
theater. The T3 can reproduce all of the commands of almost
any other infrared remote control.
A programmable graphic display. The T3 uses powerful
Windows® based software that makes it easy to place
buttons, text, graphics, symbols and icons anywhere on the
display.
A full color, high-contrast TFT LCD with bright white
backlight. The display’s transflective screen makes it easy to
read in any lighting condition – even in sunlight.
A reliable, high-resolution resistive touchpanel.
16 backlit “hard” keypad buttons that allow easy access to
frequently used functions.
A light-weight, low-profile Lithium Ion rechargeable battery
pack. The T3 can run continuously for several hours between
charges. Because the remote is normally used only a few
minutes per session, the unit typically will run for a week or
more between charges. A built-in low battery indicator
warns you when it’s time to recharge the battery.
A macro function. This feature allows the T3 to perform a
series of commands by pressing a single button. For
example, you can create a macro called “Movie” that turns
on the TV, sets the correct input, turns on the DVD player,
dims the lights, and starts playing a movie.
![](/img.php?id=563899&img=bgb.png)
T3 Universal System Controller
4
Both infrared (IR) and radio frequency (RF) output options.
You can even use both options on the same unit.
A built in motion sensor can automatically turn the unit on
when it is picked up.
A USB port for communication with the TheaterTouch
Designer programming software.
Non-volatile flash memory. The T3 will not lose any
programmed data when the battery is removed.
One-year parts and labor warranty
Available only to system integration professionals.
IMPORTANT NOTES
Please read these important notes about the T3:
The T3 should be placed in an area where it is around
normal room temperature (between 60°F to 90°F). If the
temperature is too hot, the display appears dim. If the
temperature is too cold, the display appears dark and may
respond slowly.
Do not use sharp objects on the touchscreen. It is designed to
operate with a touch of your finger.
Do not let the T3 get wet. It should not be handled with wet
hands or placed in an area where it could get wet.
Do not subject the T3 to smoke, dust, or vibrations. The
display may be damaged from excessive shock or vibration.
Only use the power supply that is provided with the T3.
Using the wrong type of power supply may result in
damage to the battery or electronic components.
![](/img.php?id=563899&img=bgc.png)
Introduction
5
Do not disassemble the unit. Service of the T3 should be
performed by authorized personnel only.
CLEANING
Occasional cleaning may be required, depending on use. It is
recommended that you create a “Clean” button somewhere on the
Home page of the T3. This button should link to a page that does
not contain commands or macros that could be inadvertently
executed while cleaning the unit. The “Clean” page could contain
a text message or graphic of your choosing such as:
To clean your T3, lightly dampen a lint-free cloth with a glass
cleaner or mild detergent, and wipe the touchscreen, keypad and
outer surfaces.
BATTERY AND DOCKING STATION
The T3 uses a Lithium-Ion rechargeable battery. This battery does
not exhibit any type of “Memory Effect” from being charged too
![](/img.php?id=563899&img=bgd.png)
T3 Universal System Controller
6
often. Since the T3 can safely be charged after each use, a docking
station is included for convenience. If left out of the docking
station, the T3 will remain in sleep mode for 1 – 2 months before
shutting down. At that point the battery must be recharged.
The T3 Docking Station can be placed on a flat surface such as a
shelf or table, or it can be mounted to a wall using the mounting
holes on the back of the unit.
If the T3 battery capacity is reduced to approximately 25 percent,
a low battery icon will appear in the top center of the display:
The low battery icon will change color to red if the battery
capacity becomes critically low:
At this point the T3 must be placed into the docking station to
recharge the battery.
The docking station LED illuminates to indicate a charge in
progress. The LED will turn off when the battery in the unit is
fully charged.
A fully discharged battery will take approximately 2-4 hours to
completely re-charge.
The T3 can remain in the docking station indefinitely without
damage to the battery.
![](/img.php?id=563899&img=bge.png)
Introduction
7
GETTING STARTED
Start by inserting the battery connector into the mating plug on
the T3. Make sure the connector is oriented properly before
attempting to insert it. Next, turn the unit on by sliding the power
switch into the “ON” position (toward the battery).
After power is applied, the T3 will take approximately ten seconds
to load the operating system, the application software, and the
user program. This long delay only occurs from a power-down
state. During normal use the T3 turns-on instantly from its sleep
mode.
The T3 is turned-on by touching any area of the display or any
keypad button. If the tilt sensor is enabled, picking up the unit
will also turn it on.
![](/img.php?id=563899&img=bgf.png)
T3 Universal System Controller
8
REMOTE REFERENCE
Front
Touchscreen
Display
Home Page
Button
Keypad
Buttons
Light Sensor
Page Scroll
Buttons
![](/img.php?id=563899&img=bg10.png)
Introduction
9
Back
Docking Station
Contacts
Lithium-ion
Battery Pack
Power
Switch
USB
Programming
Port
Audio
Speaker
IR Transmission
Window
![](/img.php?id=563899&img=bg11.png)
T3 Universal System Controller
10
DOCKING STATION REFERENCE
Back
Front
Charge Contacts
Charge LED
Power Jack
Wire Guide
Wall Mount
Holes
1-3/8 in.
(
35mm
)
![](/img.php?id=563899&img=bg12.png)
11
Chapter 3. Operation
THE TOUCHSCREEN DISPLAY
The T3 touchscreen display is organized into a series of pages.
Normally each page contains objects (buttons, text, graphics, etc.)
that are related in some way. For instance, they may all display
information necessary for controlling a particular DVD player.
By default, the T3 has one Home page—all other pages are
normally accessed from links on the Home page. In addition, any
page can contain buttons with a link to any other page.
Normally the Home page is used to display the names of the A/V
sources and other devices being controlled. The T3 will support
200 pages including the Home page.
A representation of a programmed Home page is shown below:
By default, pressing the HOME button at any time will return you
to this page. It is possible, however, to program the Home button
to behave differently if desired.
![](/img.php?id=563899&img=bg13.png)
T3 Universal System Controller
12
THE CONTROL PANEL PAGE
The Control Panel page can be displayed by first setting the T3
power switch to the off position, and then pressing and holding
the Home button while sliding the power switch to the on
position.
You can also access the Control Panel page by assigning a
“Control Panel” page link to a button using the TheaterTouch
Designer software.
A representation of the Control Panel page is shown below:
To return to the user program, either press Exit or the Home
button.
![](/img.php?id=563899&img=bg14.png)
Operation
13
BACKLIGHT LEVEL
This button displays a window that allows you to adjust the
backlight brightness and enable/disable the Ambient Light
Sensor.
If the light sensor is disabled, there is only one backlight level to
adjust. Press the left arrow or right arrow buttons to adjust. Press
the OK button when finished.
With the light sensor disabled, the backlight brightness will
always stay at the same level whenever the T3 is turned-on.
![](/img.php?id=563899&img=bg15.png)
T3 Universal System Controller
14
If the light sensor is enabled, there are two backlight levels to
adjust. Press the left arrow or right arrow buttons to adjust. Press
the OK button when finished.
With the light sensor enabled, the backlight brightness will
automatically change between the two levels, depending upon the
ambient lighting conditions.
![](/img.php?id=563899&img=bg16.png)
Operation
15
TIME OUT
This button displays a window that allows you to adjust the
amount of time the unit stays awake after the last button press.
The time is variable from 1 second to 120 seconds (the default is 10
seconds). Press the arrows to the left or right of the Time Out
setting to adjust the time. Press the OK button when finished.
This setting can have a significant effect on the run-time of the T3
between battery charges. During Sleep mode, the T3 uses virtually
no battery power.
![](/img.php?id=563899&img=bg17.png)
T3 Universal System Controller
16
TILT SWITCH
This button displays a window that allows you to adjust the
settings for the built-in tilt sensor. The tilt switch is a motion
detector that turns the remote on when activated.
On means the tilt switch is active and will wake-up the T3 when it
is moved.
Off means the tilt switch is inactive.
Press the OK button when finished.
![](/img.php?id=563899&img=bg18.png)
Operation
17
BATTERY
This button displays a window that allows you to adjust the
relative amount of time that the low battery icon appears on the
display. This setting will determine how much time you have
between the appearance of the low battery warning and the
battery becoming completely depleted. Press the OK button when
finished.
The default warning time is Medium. Depending upon the age of
the battery and your daily usage habits, it may be beneficial to
adjust this time.
![](/img.php?id=563899&img=bg19.png)
T3 Universal System Controller
18
SOUND
This button displays a window that allows you to adjust the
volume of the audible speaker. The speaker sound provides
feedback that a button was pressed. Press the arrows to the left or
right to adjust the volume. Press the OK button when finished.
There are six discrete volume settings. The lowest setting disables
the speaker.
![](/img.php?id=563899&img=bg1a.png)
Operation
19
CALIBRATE TOUCHSCREEN
This button runs a routine that allows you to calibrate the
touchscreen. Since it normally should not be necessary to calibrate
the touchscreen, this routine is included as a precaution only.
Warning: Do not attempt to calibrate the touchscreen with
your fingertip. Proper calibration requires a stylus or other
fine tip. Do not use metal objects such as ball point pens or
screwdrivers that can damage the surface of the
touchscreen.
Press the Calibrate button to continue.
Follow the directions on the display to complete the calibration
process.
![](/img.php?id=563899&img=bg1b.png)
T3 Universal System Controller
20
PROGRAMMING THE T3
The T3 is programmed using RTI’s TheaterTouch Designer software.
RTI dealers can download the software free of charge from:
www.rticorp.com/dealers
A PC running Windows® 98SE or higher with a USB port is
required. The required USB cable is included with the RTI IR-PRO
dealer kit.
21
Chapter 4. Troubleshooting
If you are having problems with your T3, please read these
troubleshooting tips before contacting technical support.
If you continue to have problems, see Chapter 5 for more
information on contacting RTI technical support.
DISPLAY IS DIM, BLANK OR UNREADABLE
Make sure the battery pack connector is attached properly and the
battery is charged.
Try adjusting the backlight level from the Control Panel page
(Refer to Chapter 3 for more details). By nature, the contrast of an
LCD screen changes with temperature, so if the remote is cold the
display will be dark and will return to normal as it warms.
USB COMMUNICATION PROBLEMS
Verify that your PC is running Windows® 98SE or higher.
Verify that the T3 USB driver was installed the first time the T3
was connected to your PC.
Verify that the T3 is present in the Device Manager within the
Windows® Control Panel.
Make sure you are using the programming cable that was
supplied by RTI and that both ends are connected securely.
Make sure the PC detects the presence of the T3. If it doesn’t,
unplug the USB cable, wait for about ten seconds, and plug it in
again.
If the download fails after some data has been transferred, try re-
sending the program.
![](/img.php?id=563899&img=bg1d.png)
T3 Universal System Controller
22
IR CODE PROBLEMS
If you are using an IR repeater system, make sure it is working
correctly with the original OEM remote. If not, you will need to
troubleshoot the IR repeater system.
If you are still having problems, try adjusting the IR code
“Minimum Repeats” value in the TheaterTouch Designer
programming software.
If the IR code is executed inside a macro that contains multiple IR
codes, try inserting a small time delay before the problem code. If
there already is a delay, try increasing it.
23
Chapter 5. Service and Support
UPDATES AND NEW PRODUCTS
For news about the latest updates, new product information and
accessories, please visit our web site at:
www.rticorp.com
CONTACTING REMOTE TECHNOLOGIES INCORPORATED
For general info, you can contact RTI at:
Remote Technologies Incorporated
Tel. (952) 253-3100
Fax (952) 253-3131
info@rticorp.com
www.rticorp.com
RTI TECHNICAL SUPPORT
At RTI, customer service and satisfaction is an utmost priority. If
you are encountering any problems or have a question about your
RTI product, please contact RTI Technical Support for assistance.
RTI provides technical support by telephone, fax or e-mail. For the
highest quality service, please have the following information
ready, or provide it in your fax or e-mail.
Your Name
Company Name
Telephone Number
E-mail Address
Product model and serial number (if applicable)
![](/img.php?id=563899&img=bg1f.png)
T3 Universal System Controller
24
If you are having a problem with hardware, please note the
equipment in your system, a description of the problem, and any
troubleshooting you have already tried.
If you are having a problem with software, please note what
version you have installed, the operating system on your PC, a
description of the problem, and any troubleshooting you have
already tried.
If you are calling about a software or programming question or
problem, please be at you computer when you place your call.
This will considerably speed up the troubleshooting process.
For Technical Support or assistance with your RTI product,
contact RTI at:
(952) 253-3137
support@rticorp.com
www.rticorp.com/support
For questions regarding Service or Repair of your RTI product,
contact RTI at:
(952) 253-3136
service@rticorp.com
www.rticorp.com/service
Please do not return products to RTI without return authorization.
25
Specifications
Power 3.6 VDC, 1300 mAH
Li-Ion Battery Pack
Power Management Automatic On/Off
(tilt switch)
Infrared Control Range 30 Feet (9.1m) @ 60
Degrees
Infrared Frequency Range 15kHz – 460kHz
Radio Frequency Control Range Up to 100 Feet (30.5m)
(with optional receivers)
Radio Frequency Carrier 433MHz
Operating Temperature +32°F to +122°F
(+0°C to +50°C)
Operating Humidity 5% to 95% Non-condensing
Display High-brightness color TFT
¼ VGA (240 x 320 pixels)
Supports 16-bit (65K) color
Touchscreen High-resolution resistive
Display size 3.5 in. (89mm) diagonal
Backlights White LED (Display)
Blue/Amber LED (Keypad)
Nominal Run Time on Full Charge 3½ hours min. continuous
(5 - 7 days average use)
Standby Time on Full Charge 30 Days
![](/img.php?id=563899&img=bg21.png)
T3 Universal System Controller
26
Battery Charge Time 3-4 Hours
Total System Memory 32MBytes Flash
(non-volatile)
Device Capability Total number of devices
limited only by memory
Macro Capability Up to 64 steps per macro
Total number of macros
limited only by memory
Macros allowed on every
button
Communications USB programming port
Dimensions Length: 7.6 in. (193mm)
Width: 3.1 in. (79mm)
Height: 1.1 in. (28mm)
Enclosure High-impact molded ABS
plastic.
Weight 7.4 oz. (210g)
with battery pack
Warranty One Year Parts & Labor
(90 days on battery pack)
All specifications are subject to change without notice.
![](/img.php?id=563899&img=bg22.png)
IR-PRO
Professional Infrared Code Capture System
Remote Technologies Incorporated
7651 Anagram Drive
Eden Prairie, MN 55344
Tel: 952-253-3100
Fax: 952-253-3131
www.rticorp.com
© 2005 Remote Technologies Inc. All rights reserved. Printed in Taiwan.
It’s Under Control ®