SMA Solar Technology BTPBG3 BT extension kit for solar inverter User Manual
SMA Solar Technology AG BT extension kit for solar inverter
User Manual english
Communication Interface for SMA Inverters SMA BLUETOOTHÂŽ PIGGY-BACK PLUS Installation Guide BTPB_Ant-eng-IUS111410 | 98-0033010 | Version 1.0 CA US SMA America, LLC Rechtliche Bestimmungen Copyright Š 2011 SMA America, LLC. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photographic, magnetic or otherwise, without the prior written permission of SMA America, LLC. Neither SMA America, LLC nor SMA Solar Technology Canada Inc. makes representations, express or implied, with respect to this documentation or any of the equipment and/or software it may describe, including (with no limitation) any implied warranties of utility, merchantability, or fitness for any particular purpose. All such warranties are expressly disclaimed. Neither SMA America, LLC nor its distributors or dealers nor SMA Solar Technology Canada Inc. nor its distributors or dealers shall be liable for any indirect, incidental, or consequential damages under any circumstances. The exclusion of implied warranties may not apply in all cases under some statutes, and thus the above exclusion may not apply.) Specifications are subject to change without notice. Every attempt has been made to make this document complete, accurate and up-to-date. Readers are cautioned, however, that SMA America, LLC and SMA Solar Technology Canada Inc. reserve the right to make changes without notice and shall not be responsible for any damages, including indirect, incidental or consequential damages, caused by reliance on the material presented, including, but not limited to, omissions, typographical errors, arithmetical errors or listing errors in the content material. All trademarks are recognized even if these are not marked separately. Missing designations do not mean that a product or brand is not a registered trademark. The BluetoothÂŽ word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SMA America, LLC and SMA Solar Technology Canada Inc. is under license. SMA America, LLC 3801 N. Havana Street Denver, CO 80239 U.S.A. SMA Solar Technology Canada Inc. 2425 Matheson Blvd. E, 8th Floor Mississauga, ON L4W 5K5, Canada Installation Guide BTPB_Ant-eng-IUS111410 Wichtige Sicherheitshinweise SMA America, LLC IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This Installation Guide contains important instructions for the communication device SMA Bluetooth PiggyâBack Plus, that must be followed during installation and maintenance of the SMA Bluetooth PiggyâBack Plus. The SMA Bluetooth PiggyâBack Plus is designed and tested according to international safety requirements, but as with all electrical and electronic equipment, certain precautions must be observed when installing and/or operating the SMA Bluetooth PiggyâBack Plus. To reduce the risk of personal injury and to ensure the safe installation and operation of the SMA Bluetooth PiggyâBack Plus, you must carefully read and follow all instructions, cautions and warnings in this Installation Guide. Warnings in this document A warning describes a hazard to equipment or personnel. It calls attention to a procedure or practice, which, if not correctly performed or adhered to, could result in damage to or destruction of part or all of the SMA equipment and/or other equipment connected to the SMA equipment or personal injury. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE is used to address practices not related to personal injury. BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Wichtige Sicherheitshinweise Other symbols in this document In addition to the safety and hazard symbols described on the previous pages, the following symbol is also used in this Installation Guide: Information This symbol accompanies notes that call attention to supplementary information that you must know and use to ensure optimal operation of the system. General warnings General warnings All electrical installations must be done in accordance with the local and National Electrical CodeÂŽ ANSI/NFPA 70 or the Canadian Electrical CodeÂŽ CSA C22.1. This document does not and is not intended to replace any local, state, provincial, federal or national laws, regulation or codes applicable to the installation and use of the SMA Bluetooth PiggyâBack Plus, including without limitation applicable electrical safety codes. All installations must conform with the laws, regulations, codes and standards applicable in the jurisdiction of installation. SMA assumes no responsibility for the compliance or noncompliance with such laws or codes in connection with the installation of the SMA Bluetooth PiggyâBack Plus. The SMA Bluetooth PiggyâBack Plus contains no user-serviceable parts. For all repair and maintenance, always return the unit to an authorized SMA Service Center. Before installing or using the SMA Bluetooth PiggyâBack Plus, read all of the instructions, cautions, and warnings on the SMA Bluetooth PiggyâBack Plus in this Installation Guide. Wiring of the SMA Bluetooth PiggyâBack Plus must be made by qualified personnel only. Installation Guide BTPB_Ant-eng-IUS111410 SMA America, LLC Table of Contents Information on this Manual. . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 2.2 2.3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appropriate Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Target Group Qualification . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of the Bluetooth Piggy-Back . . . . . . . . . . . . . . 11 Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Identifying the Bluetooth Piggy-Back . . . . . . . . . . . . . . . . 13 6.1 6.2 Preparing Bluetooth Communication . . . . . . . . . . . . . . . . 14 Detecting a Free NetID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Setting the NetID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.1 7.2 7.3 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Installation Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Installing the Bluetooth Piggy-Back . . . . . . . . . . . . . . . . . . . . . . 16 Connecting the Antenna to the Bluetooth Piggy-Back. . . . . . . . 18 Establishing Bluetooth Communication . . . . . . . . . . . . . . . 21 Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 10 10.1 10.2 Decommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Removing the Bluetooth Piggy-Back . . . . . . . . . . . . . . . . . . . . . 23 Disposing of the Bluetooth Piggy-Back . . . . . . . . . . . . . . . . . . . 25 11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC 12 12.1 12.2 12.3 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Bluetooth Piggy-Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Antenna Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 13 FCC Compliance Information . . . . . . . . . . . . . . . . . . . . . . 30 14 IC Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . 31 15 Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Installation Guide BTPB_Ant-eng-IUS111410 Information on this Manual SMA America, LLC 1 Information on this Manual Validity This manual is valid for the SMA Bluetooth Piggy-Back Plus, firmware version 02.00.03.R and higher. Target Group This manual is intended for skilled workers. Only qualified personnel are allowed to perform the tasks set forth in this manual (see section 2.2 âTarget Group Qualificationâ (page 9)). Additional Information Additional information is available at www.SMA-America.com: Document title Document type BluetoothÂŽ SMA Bluetooth - SMA Technology in Practice. Wireless SMA BluetoothÂŽ Wireless Technology Technical Information Technical description Nomenclature ⢠In this manual, SMA America Production, LLC and SMA Solar Technology Canada Inc. are hereinafter referred to as SMA. ⢠This manual refers to PV plants and small wind turbine systems collectively as "plants." ⢠In this manual the SMA Bluetooth Piggy-Back Plus is referred to as Bluetooth Piggy-Back. BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Safety 2 Safety 2.1 Appropriate Usage The Bluetooth Piggy-Back is a communication interface und is used to connect the inverter with other SMA Bluetooth-enabled devices. Only skilled workers may install and uninstall the Bluetooth Piggy-Back. The Bluetooth Piggy-Back may only be used with the following inverters: Photovoltaic inverters Wind power inverters Sunny Boy (SB) Windy Boy (WB) SB 3000US WB 3000US SB 3800-US-10 WB 5000US SB 4000US WB 6000US SB 5000US WB 7000US SB 6000US WB 8000US SB 7000US SB 8000US SB 8000TLUS-10 SB 9000TLUS-10 SB 10000TLUS-10 2.2 Target Group Qualification An electrically skilled person has received training and has demonstrated skills and knowledge regarding the functions and operation of the device. An electrically skilled person is trained to deal with the dangers and hazards involved in installing electrical systems. Installation Guide BTPB_Ant-eng-IUS111410 Safety SMA America, LLC 2.3 Safety Instructions DANGER There is a risk of lethal electric shock when touching conductive parts of the inverter. ⢠Prior to performing any work on the inverter, disconnect the inverter on the AC and DC sides (see inverter installation guide). ⢠Only skilled persons may work on the inverter. CAUTION Possible damage to health as a result of the effects of radiation. ⢠Do not stay closer than 8 in. (20 cm) to the inverter with Bluetooth Piggy-Back for any length of time. NOTICE By touching electronic components you can cause damage to or destroy the inverter through electrostatic discharge (ESD). ⢠Ground yourself before touching a component by touching the protective conductor (PE) or a non-coated part of the inverter enclosure. ⢠Avoid coming into contact with components and plug contacts. 10 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Description of the Bluetooth Piggy-Back 3 Description of the Bluetooth Piggy-Back The Bluetooth Piggy-Back allows you to establish a connection via SMA Bluetooth Wireless Technology to other SMA inverters and communication products with SMA Bluetooth (e.g., Sunny Explorer, Sunny Beam with Bluetooth). The Bluetooth Piggy-Back reads inverter data and sends the data to a communication product with SMA Bluetooth Wireless Technology. You can read or configure the inverter data using the communication product. Installation Guide BTPB_Ant-eng-IUS111410 11 Scope of Delivery SMA America, LLC 4 Scope of Delivery Check the scope of supply for completeness and any visible external damage. Please contact your dealer if the scope of supply is not complete or you find any damage. Fig 1: Scope of delivery Item 12 Quantity Designation SMA Bluetooth Piggy-Back Plus: BTPB-G3 Installation guide Label with FCC certification, IC certification and CE mark Antenna Antenna Cable Counter nut for antenna cable Cable tie BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Identifying the Bluetooth Piggy-Back 5 Identifying the Bluetooth Piggy-Back Serial Number, Assembly Name, Production Version You can find the serial number, assembly name and production version of the Bluetooth Piggy-Back on the type label. The type label is located on the front of the Bluetooth Piggy-Back. Firmware version The firmware version of the Bluetooth Piggy-Back is displayed by means of the communication product, e.g., Sunny Explorer or Sunny Beam with Bluetooth (see manual of the communication product). Installation Guide BTPB_Ant-eng-IUS111410 13 Preparing Bluetooth Communication SMA America, LLC 6 Preparing Bluetooth Communication 6.1 Detecting a Free NetID The NetID serves to distinguish PV plants with SMA Bluetooth in close proximity of each another. If another plant with SMA Bluetooth is located within 1.640 t. (500 m) of your plant, you will have to detect a free NetID. This way you will prevent setting a NetID for your plant that is already set for by another plant. If no other plant is located within 1.640 ft. (500 m), you may choose any NetID for your plant. ⢠Detecting a free NetID using the Sunny Explorer software (see Sunny Explorer help). 6.2 Setting the NetID Requirement: ⢠A free Net ID has been detected (see section 6.1). ⢠Use a screwdriver to turn the arrow of the rotary switch to the plant's NetID. Use a screwdriver with a width of 1â8 in. (2.5 mm). 14 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Preparing Bluetooth Communication Functions of the NetIDs NetID Function Bluetooth is switched off. Bluetooth is switched on. (status upon delivery) The device can connect with up to 2 of the following communication products: ⢠Computer with Bluetooth and Sunny Explorer software The device cannot establish a connection with the following devices: ⢠Inverters with integrated SMA Bluetooth ⢠Inverters with SMA Bluetooth Piggy-Back ⢠Sunny Beam with Bluetooth ⢠SMA Bluetooth Repeater ⢠SMA Bluetooth Repeater Outdoor ⢠SMA Power Injector with Bluetooth 2 to 9 and A to F Bluetooth is switched on. The device can connect with all SMA Bluetooth products with the same NetID. Installation Guide BTPB_Ant-eng-IUS111410 15 Mounting SMA America, LLC 7 Mounting 7.1 Installation Site Requirements ⢠Keep a distance of at least 3 ft. (1 m) from devices using the 2.4 GHz frequency band (e.g., WLAN devices, microwave ovens, devices with Bluetooth Wireless Technology). This will prevent reduced connection quality and data transmission speed. 7.2 Installing the Bluetooth Piggy-Back Requirement: ⢠The NetID of the plant has been set on the Bluetooth Piggy-Back (see section 6.2). E-Total 124.4kWh h-Total 2 3 5 7 S2 512h S1 COMBINED + + UNGROUNDED L1 L2 N GROUNDING ELECTRODE CONDUCTOR GROUNDED L1 L2 Fig. 2: Position of the interface socket Item Inverter *) From SB 5000US to SB 10000TLUS-10 as well as WB 5000US to WB 8000US referred to as "Enclosure type A" in the following. From SB 3000US to SB 4000US as well as WB 3000US, referred to as "Enclosure type A" in the following. *) "From [...] to [...]" refers to the list of supported inverters, see section 2.1. 16 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Mounting DANGER Risk of lethal electric shock when opening the inverter. Death or serious injuries. ⢠Disconnect the inverter on the AC and DC side (see inverter installation guide). NOTICE Electrostatic discharge can damage the inverter. ⢠Ground yourself before touching components by touching the protective conductor (PE) or a non-coated part of the inverter enclosure. 1. Disconnect and open the inverter (see inverter installation guide). 2. If another communication interface is installed on the interface socket, remove the installed communication interface (see communication interface manual). 3. Pass the cable tie through the mounting holes of the display assembly. Make sure to pass the cable tie below the display assembly. 4. Plug the Bluetooth Piggy-Back onto the interface socket, aligned to the left. Make sure to leave the two pins on the right side of the lower row of pins free. 5. Fasten the cable tie. Installation Guide BTPB_Ant-eng-IUS111410 17 Mounting SMA America, LLC 6. Cut off the surplus end of the cable tie and remove it from the inverter. 7. Connect the antenna to the Bluetooth Piggy-Back (see section 7.3). 7.3 Connecting the Antenna to the Bluetooth Piggy-Back Requirement: ⢠You have installed the Bluetooth Piggy-Back in the inverter (see section 7.2) 1. Press the left filler plug out of the inverter's enclosure opening. COMBINED 2 3 5 7 UNGROUNDED 2 3 5 7 L1 L2 GROUNDED L1 L2 UNGROUNDED 18 BTPB_Ant-eng-IUS111410 COMBINED 2. Insert the antenna cable with the cable end and the plug through the enclosure opening into the inverter. GROUNDING ELECTRODE CONDUCTOR GROUNDED GROUNDING ELECTRODE CONDUCTOR Installation Guide SMA America, LLC Mounting 3. Attach the counter nut onto the antenna cable with the serrated edges facing towards the inverter enclosure. COMBINED 2 3 5 7 GROUNDING ELECTRODE CONDUCTOR UNGROUNDED L1 GROUNDED L2 4. First tighten the counter nut by hand, then screw it onto the antenna cable's thread with a torque of 80 in-lbs (9 Nm). Spanner size of the torque wrench: 1 in. (25.4 mm). NOTICE The antenna cable can be damaged. ⢠Do not bend the antenna cable. ⢠Keep the antenna cable away from heat-conducting component parts. 5. Install the antenna cable in the inverter: BC E F 01 78 A 2 3 5 7 COMBINED 2 3 5 7 GROUNDING ELECTRODE CONDUCTOR UNGROUNDED L1 GROUNDED L2 BC E F 01 4 56 23 78 A â For inverters with enclosure type B: pass the antenna cable along the lower edge of the inverter enclosure. Pass the antenna cable towards the antenna connection of the Bluetooth Piggy-Back in a loop. 4 56 23 â For inverters with enclosure type A: pass the antenna cable towards the antenna connection of the Bluetooth Piggy-Back. E-Total 124.4kWh h-Total S2 512h S1 + + L1 L2 N Installation Guide BTPB_Ant-eng-IUS111410 19 Mounting SMA America, LLC 6. Screw the antenna cable plug to the antenna connection by hand without tools. 7. Close the inverter (see inverter installation guide). 8. Screw the antenna onto the antenna cable by hand without tools. 9. Attach the label with the FCC and IC certifications and CE mark to the right side of the inverter enclosure, on the right next to the type label. Germany BOY* Made in Germany inverter string SUNNY rman Photovoltaic SB 5000TL-20 550 2100549865 125-440 2 x 15 230 50/60 Hz 4600/5000W 20/22 FCC ID: Contains MAC: 0013A200 *XXX RFR-C11G2 Y in Ge BO Made NY inverter * SUvoNltaic string Photo SB TL-2 5000 65 5498 2100 20 BTPB_Ant-eng-IUS111410 550 440 12515 A 2x 230 0 Hz 50/6 0W /500 4600 Installation Guide SMA America, LLC Establishing Bluetooth Communication 8 Establishing Bluetooth Communication Requirement: ⢠Free NetID has been detected (see section 6.1). ⢠The NetID of the plant has been set on the Bluetooth Piggy-Back (see section 6.2). ⢠You have installed the Bluetooth Piggy-Back in the inverter (see section 7.2). or ⢠The Bluetooth Piggy-Back is pre-installed in the inverter. ⢠The antenna has been connected to the Bluetooth Piggy-Back (see section 7.3). 1. Commission the communication product (e.g., Sunny Explorer, Sunny Beam with Bluetooth; see manual of the communication product). 2. Commission the inverter with Bluetooth Piggy-Back (see inverter installation guide). 3. If the inverter with Bluetooth Piggy-Back has a different password than the plant, change the password of the inverter with Bluetooth Piggy-Back to the plant password using the Sunny Explorer software (see Sunny Explorer help). â The Bluetooth Piggy-Back is establishing a connection to other devices with SMA Bluetooth. You can read or configure the inverter data using the communication product. Installation Guide BTPB_Ant-eng-IUS111410 21 Updating the Firmware SMA America, LLC 9 Updating the Firmware You can update the firmware of the Bluetooth Piggy-Back using the Sunny Explorer software. The Bluetooth Piggy-Back remains in the inverter while the update is being performed. Requirement: ⢠The inverter's feed-in power is at least 50 W. 1. Update firmware using Sunny Explorer (see Sunny Explorer help). 2. Restart Sunny Explorer. 22 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Decommissioning 10 Decommissioning 10.1 Removing the Bluetooth Piggy-Back DANGER Risk of lethal electric shock when opening the inverter. Death or serious injuries. ⢠Disconnect the inverter on the AC and DC side (see inverter installation guide). NOTICE Electrostatic discharge can damage the inverter. ⢠Ground yourself before touching components by touching the protective conductor (PE) or a non-coated part of the inverter enclosure. 1. Unscrew the antenna from the antenna cable. 2. Disconnect and open the inverter (see inverter installation guide). 3. Unscrew the counter nut from the thread of the antenna cable. COMBINED 2 3 5 7 UNGROUNDED Installation Guide GROUNDING ELECTRODE CONDUCTOR GROUNDED L1 L2 BTPB_Ant-eng-IUS111410 23 Decommissioning SMA America, LLC 4. Unscrew the antenna cable plug from the antenna connection of the Bluetooth Piggy-Back. 5. Pull the antenna cable out of the inverter through the enclosure opening. COMBINED 2 3 5 7 UNGROUNDED GROUNDING ELECTRODE CONDUCTOR GROUNDED L1 L2 6. Cut the cable tie and remove it from inverter. 7. Remove the Bluetooth Piggy-Back from the interface socket. 24 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Decommissioning 8. Close the enclosure opening with the filler-plug. COMBINED 2 3 5 7 UNGROUNDED GROUNDING ELECTRODE CONDUCTOR GROUNDED L1 L2 9. Close the inverter (see inverter installation guide). 10. Remove the label with the FCC and IC certifications and the CE mark from the inverter. any Germany BOY* Made in Germany inverter string SUNNY Photovoltaic SB 5000TL-20 550 2100549865 125-440 2 x 15 230 50/60 Hz 4600/5000W 20/22 FCC ID: Contains MAC: 0013A200 *XXX RFR-C11G2 Y in Germ BO Made NY inverter * SUvoNltaic string Photo SB TL-2 5000 65 5498 2100 550 440 12515 A 2x 230 0 Hz /6 50 0W /500 4600 2A 10.2 Disposing of the Bluetooth Piggy-Back ⢠Observe the disposal regulations for electronic waste that apply at the installation site when disposing of the Bluetooth Piggy-Back. ⢠In order to have us dispose of the Bluetooth Piggy-Back, send the Bluetooth Piggy-Back back to SMA at your own cost, labeled "FOR DISPOSAL". Installation Guide BTPB_Ant-eng-IUS111410 25 Troubleshooting SMA America, LLC 11 Troubleshooting Problem Cause The inverter with Bluetooth The inverter with Bluetooth Piggy-Back is not shown by Piggy-Back has not been the communication product. commissioned. The inverter with Bluetooth Piggy-Back is not in feed-in operation. The Bluetooth Piggy-Back has not been installed correctly on the interface socket. NetID "0" is set on the Bluetooth Piggy-Back. NetID "1" is set on the Bluetooth Piggy-Back. 26 BTPB_Ant-eng-IUS111410 Measure ⢠Commission the inverter with Bluetooth Piggy-Back (see inverter installation guide). ⢠Wait until the inverter switches to feed-in operation. ⢠Ensure that the Bluetooth Piggy-Back has been correctly installed on the interface socket (see section7.2). ⢠Set the NetID of the plant on the Bluetooth Piggy-Back (see section 6.2). ⢠Set another NetID on the Bluetooth Piggy-Back. Installation Guide SMA America, LLC Problem The connection between the inverter with the Bluetooth Piggy-Back and the communication product is disturbed. Troubleshooting Cause The distance between the inverter with Bluetooth PiggyBack and the communication product is too large. The Bluetooth radio waves are being weakened by obstacles (e.g., walls, ceilings, doors). The distance between the inverter with Bluetooth PiggyBack and other devices using the 2.4 GHz frequency band is too small. The antenna has not been connected correctly to the Bluetooth Piggy-Back. The Bluetooth Piggy-Back firmware cannot be updated. Installation Guide The inverter's feed-in power is less than 50 W. Measure ⢠Decrease the distance between the inverter with Bluetooth Piggy-Back and the communication product. ⢠If required, use an SMA Bluetooth Repeater to cover the dead zones. ⢠Position the communication product in such a manner as to prevent obstacles from disturbing the Bluetooth radio waves. ⢠If required, use an SMA Bluetooth Repeater to cover the dead zones. ⢠Make sure that the requirements for the installation site of the inverter with Bluetooth Piggy-Back are met (see section 7.1). ⢠Ensure that the antenna is screwed onto the antenna cable correctly (see section 7.3). ⢠Ensure that the antenna cable plug is correctly screwed onto the antenna connection of the Bluetooth Piggy-Back (see section 7.3). ⢠Only update the firmware if the feed-in power is at least 50 W. BTPB_Ant-eng-IUS111410 27 Technical Data SMA America, LLC 12 Technical Data 12.1 Bluetooth Piggy-Back Mechanical Data Width x length Weight 2 in. x 31â8 in. x (50 mm x 81 mm) 21â8 oz (60 g) Communication Communication interface Maximum free-field communication range when installed, if inverter lid is closed and antenna is connected Bluetooth 328 ft. (100 m) Connections Number of 10-pin socket connectors Number of 14-pin socket connectors Number of 1-pin reverse polarity sub-miniature A-socket Ambient Conditions Ambient temperature Relative humidity*) Maximum height**) Degree of protection when installed *) **) 28 â 40 °F ⌠+185 °F ( â 40 °C ⌠+85 °C) 5 % ⌠95 % 9.84 ft. (3.00 m) NEMA 3 R Non-condensing Above mean sea level BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC Technical Data 12.2 Antenna Mechanical Data Diameter x length Weight 13 â32 in. x 51â8 in. (10 mm x 130 mm) â16 oz (12 g) Ambient Conditions Ambient temperature Relative humidity Maximum height Degree of protection â 40 °F ⌠+185 °F ( â 40 °C ⌠+85 °C) 5 % ⌠95 % 9.84 ft. (3.00 m) NEMA 3 R Connections Number of 1-pin reverse polarity sub-miniature A-socket 12.3 Antenna Cable Mechanical Data Diameter x length Weight 1â in. x 161â2 in. (5 mm x 420 mm) 15â oz (51 g) 18 Ambient Conditions Ambient temperature Relative humidity Maximum height â 40 °C ⌠+85 °C 5 % ⌠95 % 9.84 ft. (3.00 m) Connections Number of 1-pin reverse polarity sub-miniature A-socket Number of 1-pin reverse polarity sub-miniature A panel jack Installation Guide BTPB_Ant-eng-IUS111410 29 FCC Compliance Information SMA America, LLC 13 FCC Compliance Information The SMA communication device Bluetooth Piggy-Back Plus contains FCC ID: SVFâBTPBG3. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A & B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the separation between the equipment and the receiver. ⢠Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. ⢠The user is cautioned that changes or modifications not expressly approved by SMA America, Inc. could void the userâs authority to operate this equipment. RF-exposure Statement The SMA Bluetooth Piggy-Back Plus contains a modular transmitter. Thus it must have a separation of at least 8 in. (20 cm) between the antenna and the body of the user or nearby persons, excluding hands, wrists, feet, and ankles. 30 BTPB_Ant-eng-IUS111410 Installation Guide SMA America, LLC IC Compliance Information 14 IC Compliance Information The SMA communication device Bluetooth Piggy-Back Plus contains IC: 9440AâBTPBG3. This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation Guide BTPB_Ant-eng-IUS111410 31 Contact SMA America, LLC 15 Contact If you have technical problems concerning our products, contact the SMA Serviceline. We require the following information in order to provide you with the necessary assistance: ⢠Inverter type ⢠Type and number of modules connected ⢠Way of communication ⢠Sunny Boy failure or warning number ⢠Display of the Sunny Boy SMA Solar Technology America, LLC 6020 West Oaks Blvd, Ste 300 Rocklin, CA 95765 Tel. +1 916 625 0870 Tel. +1 877-MY SMA TECH Tel. +1 877 697 6283 (Toll free, available for USA, Canada and Puerto Rico) Fax +1 916 625 0871 Service@SMA-America.com www.SMA-America.com SMA Solar Technology Canada Inc. 2425 Matheson Blvd E 8th Floor Mississauga, ON L4W 5K5 Canada 32 BTPB_Ant-eng-IUS111410 Installation Guide 4."4PMBS5FDIOPMPHZ XXX4."4PMBSDPN 4.""NFSJDB --$ XXX4.""NFSJDBDPN
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c320 44.293068, Sun Jul 08 2007 18:10:11 Creator Tool : FrameMaker 8.0 Modify Date : 2011:05:31 11:33:30+02:00 Create Date : 2011:05:31 11:30:15Z Metadata Date : 2011:05:31 11:33:30+02:00 Format : application/pdf Title : untitled Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:65ecad4b-79d7-4d00-8e53-4e175ec6a790 Instance ID : uuid:f7236197-9ef0-4f46-8eda-b93ce80c77ae Page Count : 36 Creator : FrameMaker 8.0EXIF Metadata provided by EXIF.tools