WINIA Electronics 7NFCMC907D Monitor User Manual for Color Display Monitor
Dongbu Daewoo Electronics Corporation Monitor Users Manual for Color Display Monitor
Users Manual for Color Display Monitor
USER’S GUIDE COLOR MONITOR Model No : 907D/907DF http://www.dwe.co.kr FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or TV technician for help. CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CANADIAN NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS CANADIEN Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. WICHTIGE INFORMATIONEN Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät in Betrieb nehmen! Lesen Sie außerdem die Bedienungsanleitung komplett und sorgfältig durch, da nur in diesem Fall eine problemlose Inbetriebnahme erwartet werden kann. Achten Sie darauf, daß das Gerät nur in eine 230V Steckdose eingesteckt wird. Die Steckdose sollte jederzeit frei zugänglich sein um bei einem evtl. auftretenden Notfall das Gerät schnell vom Netz zu trennen. Achten Sie desweiteren darauf, daß die Netzanschlußleitung nicht mechanisch beansprucht oder sonstwie beschädigt wird. Öffnen Sie das Gerät niemals! Im Inneren befinden sich Teile mit gefährlicher Spannung. Bevor Sie das Gerät reinigen, ziehen Sie bitte den Netzstecker aus der Steckdose. Säubern Sie dann das Gerät mit einem feuchten (keinesfalls tropfnassen) Lappen. Stellen Sie das Gerät an einem ergonomisch günstigen Ort auf und sorgen Sie dafür, daß der Monitor mit nach ISO 9241 -3, -7, -8 geprüfter Peripherie betrieben wird, da nur unter diesen Umständen ein optimaler ergonomischer Betrieb des Gerätes sichergestellt ist. Falls Sie dennoch Fragen haben, auf die die Bedienungsanleitung keine hinreichende Antwort geben kann, so kontaktieren Sie bitte den nächsten Fachhändler. Maschinenlärminformationsverordnung 3. GSGV, 18.01 1991: Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A) oder wenigergemäß ISO 7779. Emission Characteristics Tested by SEMKO A sample of this type has been tested and has shown compliance with theguidelines in the swedish document MPRII. DECLARATION OF CONFORMITY This product is also designed for IT power system with phase to phase voltage of 230V. We, Manufacturer / Importer DAEWOO ELECTRONICS CO., Ltd 686, Ahyon-dong, Mapo-gu, Seoul, Korea The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. declare under our sole responsibility that the product, Color Display monitor 907D 907DF to which this declaration relates is in conformity with the following standard(s) or other normative document(s) Safety : EN60950/1992/A1:1993/A2:1993 A3:1995/A4:1997 EMC : EN 55022/8.1994/A1:1995/A2:1997 EN 55024/1998 EN 61000 -3-2,3/1995 following the provisions of 89/336 EEC-EMC Directive and the provisions of 73/23 EEC-Low Voltage Directive. Handed over by : Jong K. Choi, Director. Display Business Division. 2002 Seoul Signature : J.K.Choi Director. Display Business Division. DAEWOO ELECTRONICS CO., LTD. As an ENERGY STAR® Partner, Daewoo Electronics Co., Ltd. has determined that this product meets the Energy Star® guidelines for energy efficiency. The appliance is not intended for use by young children or infirm persons without supervision ; Young children should be supervised to ensure that they do not play with the appliance. CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 Connecting the Signal Cable and Power Cord..................... 3 Operation & Adjustment ...................................................... 4 Specifications ........................................................................... 9 Factory Preset Timings ........................................................... 9 Troubleshooting ..................................................................... 10 INTRODUCTION This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s guide carefully before installing your monitor, then keep it near your monitor for quick reference. First, please check that the contents of the box corresponds with the following checklist : Color monitor Power cord User’s Guide Warranty card (Optional) If any item is missing or damaged, please contact your dealer. Please keep the box and packing materials so that you may properly store or transport your monitor. English - 1 SETUP PRODUCT FEATURES CONNECTING THE SIGNAL CABLE AND POWER CORD The convenient and user-friendly on-screen display allows for easy and accurate adjustments of horizontal and vertical screen size and position, geometry and screen color. The monitor supports a safe working environment in strict compliance with the MPR II standard for low emissions (TCO Optional). The monitor complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility. Advanced microcircuitry makes setup and configuration fast and effortless. The monitor features Advanced Color Controls for fine-tuning to meet your own personal tastes or application requirements. Use the on-screen controls to adjust the color temperature, RGB gain value for the best possible screen color and intensity. 1. Turn off the computer and monitor. 2. Connect the 15 pin D-sub connector to the output port of the video card in your computer. 3. Tighten the screws of the connector. 4. Plug the power cord into the AC receptacle located on the back of the monitor. 5. Plug the other end of the power cord into the AC outlet. Press the menu button and activate the Self-Diagnosis menu to determine whether your monitor is functioning normally, not receiving a signal or is receiving a signal that is out of scanning range. Activate the higher refresh rates of the monitor to stabilize the screen and eliminate the annoying flicker that contributes to eye-strain and headaches. The “borderless” full-screen display capability works under all graphic modes and provides a larger viewing area than conventional monitors, giving you a better picture with more workspace. The monitor 907DF which has applied the DynaFlat CDT offers creating sharper and cleaner images even at the outer most edges of the screen. Signal Cable Power Cord If your power cord is PC-to-Monitor type, plug the other end of the power cord into the AC receptacle in the computer. English - 2 English - 3 OPERATION & ADJUSTMENT KEY PROCESS CONTROL PANEL MENU 1 POWER 2 POWER Indicator shows both normal operation and power management status with power indicator light. swithes the monitor on and off. BRIGHTNESS MENU MENU CONTRAST MENU (*) turns the OSD window on and moves from top menu to sub menu in the OSD window. OSD OFF (*) moves cursor to the left window in the OSD window and decreases value of any selected function. moves cursor to the right window in the OSD window and increases the value of any selected function. 5 MENU MENU • When you choose the icon OSD screen. on the OSD window, you can exit the (*) moves cursor to the high window in the OSD window and increases the value of V.Size or V.Center. HOT KEY BRIGHTNESS CONTRAST ( *) moves cursor to the low window in the OSD window and decreases the value of V.Size or V.Center. ( * ) : Hot Key English - 4 English - 5 OSD FUNCTIONS ICON CONTROL FUNCTION ICON CONTROL FUNCTION LANGUAGE Select language for OSD (5 languages). H MOIRE Adjust the horizontal picture moire cancellation. H. CENTER & Adjust the position of the display horizontally(left or right) and vertically (up or down). V MOIRE Adjust the vertical picture moire cancellation. FOCUS Adjust the focus image. ZOOM Adjust the display width & height at the same time. PINCUSHION Adjust the left and right margins for more convex or more concave margins. V. CENTER COLOR TEMP. Choose different preset color temperatures or set your own customized color parameters. RED GAIN Adjust the red gain. GREEN GAIN Adjust the green gain. BLUE GAIN Adjust the blue gain. TRAPEZOID Adjust the trapezoid of the screen by moving the lines inward or outward. RED BIAS Adjust the red bias. PIN BALANCE Adjust the side balance when the sides of the screen are bowed towards left or right. GREEN BIAS Adjust the green bias. PARALLELO -GRAM Adjust the parallelogram when the screen is leaning left or right. BLUE BIAS Adjust the blue bias. T. PIN CORNER Adjust the pin corner top when the top sides of the screen are bowed. H. SIZE & Adjust the width (horizontal size) and the height (vertical size) of the display. B. PIN CORNER Adjust the pin corner bottom when the bottom sides of the screen are bowed. ROTATION Adjust the rotation when the screen is tilted left or right. V. SIZE H LINEARITY Adjust the horizontal linearity. V LINEARITY Adjust the vertical linearity. English - 6 English - 7 SPECIFICATIONS ICON CONTROL FUNCTION DEGAUSS Degaussing keeps the monitor free from unwanted magnetism that can result in color impurity. STATUS Display horizontal & vertical frequency and polarity. POWER SAVER YES : VESA DPMS operation. NO : NO DPMS operation. RECALL Reset the screen to the Factory Preset Display Settings. TEST PATTERN Display a RGB Color Bar to determine whether the screen color is expressed normally or not. Model Names 907D CDT Size Diagonal visible image area Dot Pitch Synchronization Horizontal Vertical Plug and Play Power Saving Power Source Power Consumption Dimension-W x H x D (set with stand) Weight-unpacked(lbs/Kg) Operating Temperature 907DF 19-inch 19-inch DynaFlat 18-inch 18-inch 0.25 mm 0.24 mm 30 - 95 KHz 50 - 160 Hz VESA DDC Compatible EPA, VESA DPMS, Nutek Compliant 100-240 Vac, 50/60Hz (Free Voltage) 120 W 444 x 459 x 460 mm 444 x 459 x 458 mm 40.8/18.5 45.6/20.7 10 ~ 40°C /50 ~ 104°F The specification can be changed without any prior notice to improve the quality of the product. SELF DIAGNOSIS When the monitor doesn’t display, if you press any key, Self Diagnosis screen is displayed. The Self Diagnosis function checks if the status of the monitor is No Signal or Out of range. No Signal screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode. Out of Range screen is displayed when the applied frequency is under or over normal range. Normal range H : 30 - 95 KHz V : 50 - 160 Hz English - 8 FACTORY PRESET TIMINGS Mode Resolution (dots X lines) VGA 480 H.Freq (KHz) V.Freq(Hz) Remark 640 X 480 31.5 60 Non-interlaced VGA 400 720 X 400 31.3 70 Non-interlaced VESA 43K 640 X 480 43.3 85 Non-interlaced VESA SVGA 85 800 X 600 53.7 85 Non-interlaced VESA 60K 1024 X 768 60.0 75 Non-interlaced VESA 1024/85 1024 X 768 68.7 85 Non-interlaced VESA 1280/75 1280 X 1024 80.0 75 Non-interlaced VESA 1280/85 1280 X 1024 91.1 85 Non-interlaced English - 9 TROUBLESHOOTING Symptom No picture. Check Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. POWER LED is not Check if power switch is in the on position. lit. Check if the power cord is correctly connected. Image is unstable. Check if the signal cable is suitable to the video card. Image is not centered, too small or too large. Adjust H&V Size or H&V Center to get the proper image. Picture bounces or a Keep the devices that may cause electrical wave pattern is interference away from the monitor. present in the picture. See the FCC information at the front cover of the manual. Color looks blotchy. Operate Degauss once. Picture is blurred. Adjust Contrast and Brightness. Operate Degauss once. Edges of available area on the screen are not straight. Adjust Geometry Control (Pincushion, Trapezoid..). English - 10 S/N : 9978633100
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:04:02 10:54:46 Producer : Acrobat Distiller 4.0 for Macintosh Modify Date : 2002:06:04 11:19:21+09:00 Page Count : 9EXIF Metadata provided by EXIF.tools