WINIA Electronics 7NFCML520B LCD Monitor User Manual L520B
Dongbu Daewoo Electronics Corporation LCD Monitor L520B
Users Manual for L520B LCD Monitor
USER’S GUIDE TFT LCD-MONITOR Model No : L520B http://www.dwe.co.kr FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or TV technician for help. CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CANADIAN NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS CANADIEN Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. WICHTIGE INFORMATIONEN Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät in Betrieb nehmen! Lesen Sie sich außerdem die Bedienungsanleitung komplett und sorgfältig durch, da nur in diesem Fall eine problemlose Inbetriebnahme erwartet werden kann. Achten Sie darauf, daß das Gerät nur in eine 230V Schuko-Steckdose eingesteckt wird. Die Steckdose sollte jederzeit frei zugänglich sein um bei einem evtl. auftretenden Notfall das Gerät schnell vom Netz zu trennen. Achten Sie desweiteren darauf, daß die Netzanschlußleitung nicht mechanisch beansprucht oder sonstwie beschädigt wird. Offnen Sie das Gerät niemals! Im Inneren befinden sich Teile mit gefährlicher Spannung. Bevor Sie das Gerät reinigen, ziehen Sie bitte den Netzstecker aus der Steckdose. Säubern Sie dann das Gerät mit einem feuchten (keinesfalls tropfnassen) Lappen. Stellen Sie das Gerät an einem ergonomisch günstigen Ort auf und sorgen Sie dafür, daß der Monitor mit nach ISO 9241 -3, -7, -8 geprüfter Peripherie betrieben wird, da nur unter diesen Umständen ein optimaler ergonomischer Betrieb des Gerätes sichergestellt ist. Falls Sie dennoch Fragen haben, auf die die Bedienungsanleitung keine hinreichende Antwort geben kann, so kontaktieren Sie bitte den nächsten Fachhändler. Maschinenlärminformationsverordnung 3. GSGV, 18.01 1991: Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A) oder wenigergemäß ISO 7779. Emission Characteristics Tested by SEMKO A sample of this type has been tested and has shown compliance with theguidelines in the swedish document TCO 99. DECLARATION OF CONFORMITY This product is also designed for IT power system with phase to phase voltage of 230V. We, Manufacturer / Importer DAEWOO ELECTRONICS CO., Ltd 541, 5-Ga, Namdaemoon-Ro, Jung-Gu Seoul, Korea declare under our sole responsibility that the product, TFT LCD monitor L520B to which this declaration relates is in conformity with the following standard(s) or other normative document(s) Safety : EN60950/1992/A1:1993/A2:1993 A3:1995/A4:1997 EMC : EN 55022/8.1994/A1:1995/A2:1997 EN 55024/1998 EN 61000 -3-2,3/1995 following the provisions of 89/336 EEC-EMC Directive and the provisions of 73/23 EEC-Low Voltage Directive. Handed over by : Jong K. Choi, Director. Display Business Division. Nov , 2001 Seoul Signature : J.K.Choi Director. Display Business Division. DAEWOO ELECTRONICS CO., LTD. The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an ENERGY STAR® Partner, Daewoo Electronics Co., Ltd. has determined that this product meets the Energy Star® guidelines for energy efficiency. The appliance is not intended for use by young children or infirm persons without supervision ; Young children should be supervised to ensure that they do not play with the appliance. CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 Installing the Stand .............................................................. 3 Connecting the 15 Pin Signal Cable and Power Cord ......... 4 Operation & Adjustment ...................................................... 5 Specifications ......................................................................... 11 Factory Preset Timings ......................................................... 12 Changing the Stand ............................................................... 13 Troubleshooting ..................................................................... 15 Appendix Description for D-sub Connector INTRODUCTION This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s guide carefully before installing your monitor, then keep it near your monitor for quick reference. First, please check that the contents of the box corresponds with the following checklist : TFT LCD monitor Power cord 15 pin signal cable User’s guide Warranty card (Optional) If any item is missing or damaged, please contact your dealer. Please keep the box and packing materials so that you may properly store or transport your monitor. English - 1 SETUP PRODUCT FEATURES INSTALLING THE STAND The monitor is designed for use in a small work area or for those who need more work space on the desk. Unfolding the stand The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. The monitor supports a safe working environment in strict compliance with the TCO 99 standard for low emissions . The monitor complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility. Advanced microcircuitry makes setup and configuration fast and effortless. The monitor features Advanced Color Controls for fine-tuning to meet your own personal tastes or application requirements. Use the on-screen controls to adjust the color temperature, RGB gain value for the best possible screen color and intensity. Press the menu button and activate the Self-Diagnosis menu to determine whether your monitor is functioning normally, not receiving a signal or is receiving a signal that is out of scanning range. Folding the stand Activate the higher refresh rates of the monitor to stabilize the screen and eliminate the annoying flicker that contributes to eye-strain and headaches. The “borderless” full-screen display capability works under all graphic modes and provides a larger viewing area than conventional monitors, giving you a better picture with more workspace. The monitor supports the optimal display performance with 1024x768 at 75Hz. Fold the stand with pressing this lever. English - 2 English - 3 OPERATION & ADJUSTMENT CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD 1. Turn off the computer and monitor. CONTROL PANEL 1 POWER 2 POWER Indicator shows both normal operation and power management status with power indicator light. swithes the monitor on and off. 2. Connect the 15 pin signal cable to the output port of the video card in your computer and monitor. 3. Tighten the screws of the 15 pin signal cable. 4. Plug the power cord into the AC receptacle located on the back of the monitor. 5. Plug the other end of the power cord into the AC outlet. (*) moves cursor to the right or low window in the OSD window and increases the value of any selected function. 5 MENU (*) moves cursor to the left or high window in the OSD window and decreases value of any selected function. 6 EXIT turns the OSD window on and moves from top menu to sub menu in the OSD window. turns the OSD (On-Screen Display) window off and moves from sub menu to top menu in the OSD window. AC POWER 7 AUTO ( * ) 15 pin signal cable Power Cord English - 4 launches the AUTO TRACKING function directly. English - 5 ( * ) : Hot Key ADJUSTMENT PROCEDURE KEY PROCESS MENU 1024X768 60K UT L TY 75 UT L TY OSD MENU UT L TY EXIT Adjust the CLOCK control. OSD MENU SHARPNESS No Is the H.Size proper? EXIT Yes Is the noise displayed on the screen? SHARPNESS Perform the AUTO POSITION. No Yes EXIT Perform the AUTO TRACKING. OSD OFF Is the noise displayed on the screen yet? HOT KEY No AUTO AUTO TRACKING When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. Yes Adjust the CLOCK FINE until the screen is cleared. Yes BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly. : decreases brightness : increases brightness English - 6 Is the noise displayed on the screen yet? No End English - 7 OSD FUNCTIONS ICON CONTROL FUNCTION ICON CONTROL FUNCTION LANGUAGE Select language for OSD (6 languages). OSD TIME OUT Adjust the display OSD Menu. CLOCK Adjust the width (horizontal size) of the screen image. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen. AUTO POSITION Choose automatically the proper horizontal position and vertical position & size of the screen image. CONTRAST Adjust the contrast of image, the difference between light and dark areas on the screen. Adjust the horizontal & vertical picture image quality and size. AUTO TRACKING Choose different preset color temperatures COLOR or set your own customized color TEMPERATURE parameters. RED CONTROL Adjust the red color. GREEN CONTROL Adjust the green color. BLUE CONTROL Adjust the blue color. H. CENTER & Adjust the position of the display horizontally (left or right) and vertically (up or down). V. CENTER OSD SHARPNESS Adjust the display image quality (if the screen proceed to scaling up). OSD POSITION Adjust the OSD position horizontally (left or right) and vertically (up or down). English - 8 English - 9 SPECIFICATIONS SELF DIAGNOSIS Panel If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is “No Signal”, “Out of range” or “Check Cable”. “No Signal” screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode. “Out of Range” screen is displayed when the applied frequency is under or over normal range. Normal range (Non-interlaced mode only) H : 30 - 62 KHz V : 50 - 75 Hz “Check Cable” screen is displayed when the D-Sub signal connector is not connected. Synchronization Size Pixel Pitch Viewing Angle Contrast Ratio Brightness Color Filter Horizontal Vertical Video Bandwidth Max Resolution(Optimal) Colors Display Area PC Input Signal Sync Video AV Input Signal (Option) Video Audio TV Receiving Signal TV Tuner (Option) External Speaker Max. Output (Option) Plug and Play Power Source Power Consumption Dimension-W x H x D Weight-net/gross Power Saving Tilt Range Operating Temperature English - 10 15-inch (38 cm) diagonal 0.297 x 0.297 mm 60°(Right/Left) 40°(up), 60°(down) 350:1 contrast ratio (typ) 250cd/m2 brightness (typ) RGB vertical stripe 30 - 62 KHz 50 - 75 Hz 80 MHz 1024 x 768 a 75Hz 6 bit (16.7M Colors) 304.1mm x 228.1mm H/V separate (TTL) 15 pin mini D-sub (Analog RGB) DVI-D(Option) CVBS(RCA), S-Video(Mini-DIN) RCA Left+Right Input Stereo Mini Jack Input & Output NTSC, PAL 6W (Left 3W+Right 3W) VESA DDC Compatible 100-240 Vac, 50/60 Hz (Free Voltage) 26 W 370 x 352 x 205 mm (with stand) 370 x 312 x 60 mm (without stand) 4.2/5.5 Kg (9.2/12.1 lbs) EPA, VESA DPMS, Nutek Compliant 5° forward, 30° backward 10 ~ 40°C /50 ~ 104°F English - 11 FACTORY PRESET TIMINGS CHANGING THE STAND REMOVING THE STAND VESA MODES Mode VGA Resolution (dots X lines) 640 X 480 a 60Hz H.Freq (KHz) V.Freq (Hz) Remark 31.5 60 Non-interlaced 37.9 72 Non-interlaced VGA 640 X 480 a 72Hz 640 X 480 a 75Hz 37.5 75 Non-interlaced SVGA 800 X 600 a 56Hz 35.2 56 Non-interlaced SVGA 800 X 600 a 60Hz 37.9 60 Non-interlaced SVGA 800 X 600 a 72Hz 48.1 72 Non-interlaced SVGA 800 X 600 a 75Hz 46.9 75 Non-interlaced XGA 1024 X 768 a 60Hz 48.4 60 Non-interlaced XGA 1024 X 768 a 70Hz 56.5 70 Non-interlaced XGA 1024 X 768 a 75Hz 60.0 75 Non-interlaced VGA 1. Remove 2 screws. 2. Remove the Stand Rear. IBM MODES EGA Resolution (dots X lines) 640 X 350 a 70Hz DOS 720 X 400 a 70Hz Mode H.Freq (KHz) V.Freq (Hz) Remark 31.5 70 Non-interlaced 31.3 70 Non-interlaced MAC MODES VGA Resolution (dots X lines) 640 X 480 a 67Hz SVGA 832 X 624 a 75Hz Mode H.Freq (KHz) V.Freq (Hz) 3. Remove 2 screws. 4. Remove the Stand Base. Remark 35.0 67 Non-interlaced 49.7 75 Non-interlaced The LCD Monitor has only Non-interlanced modes without flicker. The specification can be changed without any prior notice to improve the quality of the product. The LCD panel may have some defective pixels (e.g. slightly light or dark) due to a characteristic of the LCD panel. But there is no defect in your LCD product itself. English - 12 English - 13 TROBLESHOOTING REMOVING THE COVER Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Remove the Cover. Check if the signal cable is correctly connected to the video card. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. ATTACHING THE MONITOR WITH THE ARM-STAND(OPTION) Tighten 4 screws. POWER LED is not Check if power switch is in the on position. lit. Check if the power cord is correctly connected. Image is unstable. Check if the signal cable is suitable to the video card. Image is not centered, too small or too large. Adjust Clock or H&V Center to get the proper image. Picture bounces or a Keep the devices that may cause electrical interference away from the monitor. wave pattern is present in the See the FCC information at the front cover of the picture. manual. Picture is blurred. Adjust Contrast and Brightness. Use the VESA approved arm-stand. (75x75 mm hole spacing) English - 14 English - 15 APPENDIX DESCRIPTION FOR D-SUB CONNECTOR Pin Signal 10 11 12 13 14 15 Red Green Blue GND GND GND-Red GND-Green GND-Blue +5Vdc GND-H.Sync GND-V.Sync Bi-directional Data(SDA) Horizontal Sync Vertical Sync(VCLK) Data Clock(SCL) 10 15 * GND=Ground S/N:9978632100
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:02:19 17:22:54-08:00 Modify Date : 2002:02:19 17:22:54-08:00 Page Count : 12 Creation Date : 2002:02:20 01:22:54Z Mod Date : 2002:02:20 01:22:54Z Producer : Acrobat Distiller 5.0 (Windows) Author : Administrator Metadata Date : 2002:02:20 01:22:54Z Creator : Administrator Title : L520B User Manual.pdfEXIF Metadata provided by EXIF.tools