WINIA Electronics 7NFCML700C TFT LCD Monitor User Manual L700C Users Manual
Dongbu Daewoo Electronics Corporation TFT LCD Monitor L700C Users Manual
USer Manual
USER’S GUIDE TFT LCD-MONITOR Model No : L700C http://www.dwe.co.kr FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or TV technician for help. CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CANADIAN NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS CANADIEN Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. WICHTIGE INFORMATIONEN Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät in Betrieb nehmen! Lesen Sie sich außerdem die Bedienungsanleitung komplett und sorgfältig durch, da nur in diesem Fall eine problemlose Inbetriebnahme erwartet werden kann. Achten Sie darauf, daß das Gerät nur in eine 230V Schuko-Steckdose eingesteckt wird. Die Steckdose sollte jederzeit frei zugänglich sein um bei einem evtl. auftretenden Notfall das Gerät schnell vom Netz zu trennen. Achten Sie desweiteren darauf, daß die Netzanschlußleitung nicht mechanisch beansprucht oder sonstwie beschädigt wird. Offnen Sie das Gerät niemals! Im Inneren befinden sich Teile mit gefährlicher Spannung. Bevor Sie das Gerät reinigen, ziehen Sie bitte den Netzstecker aus der Steckdose. Säubern Sie dann das Gerät mit einem feuchten (keinesfalls tropfnassen) Lappen. Stellen Sie das Gerät an einem ergonomisch günstigen Ort auf und sorgen Sie dafür, daß der Monitor mit nach ISO 9241 -3, -7, -8 geprüfter Peripherie betrieben wird, da nur unter diesen Umständen ein optimaler ergonomischer Betrieb des Gerätes sichergestellt ist. Falls Sie dennoch Fragen haben, auf die die Bedienungsanleitung keine hinreichende Antwort geben kann, so kontaktieren Sie bitte den nächsten Fachhändler. Maschinenlärminformationsverordnung 3. GSGV, 18.01 1991: Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A) oder wenigergemäß ISO 7779. Emission Characteristics Tested by SEMKO A sample of this type has been tested and has shown compliance with theguidelines in the swedish document TCO 99. DECLARATION OF CONFORMITY This product is also designed for IT power system with phase to phase voltage of 230V. We, Manufacturer / Importer DAEWOO ELECTRONICS CO., Ltd 541, 5-Ga, Namdaemoon-Ro, Jung-Gu Seoul, Korea declare under our sole responsibility that the product, TFT LCD monitor L700C to which this declaration relates is in conformity with the following standard(s) or other normative document(s) Safety : EN60950/1992/A1:1993/A2:1993 A3:1995/A4:1997 EMC : EN 55022/8.1994/A1:1995/A2:1997 EN 55024/1998 EN 61000 -3-2,3/1995 following the provisions of 89/336 EEC-EMC Directive and the provisions of 73/23 EEC-Low Voltage Directive. Handed over by : Jong K. Choi, Director. Display Business Division. Nov , 2001 Seoul Signature : J.K.Choi Director. Display Business Division. DAEWOO ELECTRONICS CO., LTD. The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an ENERGY STAR® Partner, Daewoo Electronics Co., Ltd. has determined that this product meets the Energy Star® guidelines for energy efficiency. The appliance is not intended for use by young children or infirm persons without supervision ; Young children should be supervised to ensure that they do not play with the appliance. CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 Connecting the 15 Pin Signal Cable and Power Cord ......... 3 Operation & Adjustment ...................................................... 4 Specifications ......................................................................... 10 Factory Preset Timings ......................................................... 12 Changing the Stand ............................................................... 13 Troubleshooting ..................................................................... 15 Appendix Description for D-sub Connector INTRODUCTION This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s guide carefully before installing your monitor, then keep it near your monitor for quick reference. First, please check that the contents of the box corresponds with the following checklist : TFT LCD monitor Power cord 15 pin signal cable User’s guide Warranty card (Optional) If any item is missing or damaged, please contact your dealer. Please keep the box and packing materials so that you may properly store or transport your monitor. English - 1 SETUP PRODUCT FEATURES CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD The monitor is designed for use in a small work area or for those who need more work space on the desk. 1. Turn off the computer and monitor. The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. 2. Connect the 15 pin signal cable to the output port of the video card in your computer and monitor. The monitor supports a safe working environment in strict compliance with the TCO 99 standard for low emissions . The monitor complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility. Advanced microcircuitry makes setup and configuration fast and effortless. 3. Tighten the screws of the 15 pin signal cable. 4. Plug the power cord into the AC receptacle located on the back of the monitor. 5. Plug the other end of the power cord into the AC outlet. The monitor features Advanced Color Controls for fine-tuning to meet your own personal tastes or application requirements. Use the on-screen controls to adjust the color temperature, RGB gain value for the best possible screen color and intensity. Press the menu button and activate the Self-Diagnosis menu to determine whether your monitor is functioning normally, not receiving a signal or is receiving a signal that is out of scanning range. Activate the higher refresh rates of the monitor to stabilize the screen and eliminate the annoying flicker that contributes to eye-strain and headaches. The “borderless” full-screen display capability works under all graphic modes and provides a larger viewing area than conventional monitors, giving you a better picture with more workspace. AC POWER The monitor supports the optimal display performance with 1280x1024 at 60Hz. 15 pin signal cable Power Cord English - 2 English - 3 OPERATION & ADJUSTMENT CONTROL PANEL KEY PROCESS 1 POWER 2 POWER Indicator MENU shows both normal operation and power management status with power indicator light. swithes the monitor on and off. 1280X1024 80K UT L TY 75 UT L TY OSD OSD SELECT UT L TY EXIT SELECT SHARPNESS EXIT SHARPNESS EXIT (*) OSD OFF moves cursor to the right or low window in the OSD window and increases the value of any selected function. (*) moves cursor to the left or high window in the OSD window and decreases value of any selected function. HOT KEY AUTO AU TO TRACK I NG 5 SELECT 6 MENU moves from top menu to sub menu in the OSD window and opens the function window for the selected icon. turns the OSD window on. BRIGHTNESS 8 AUTO ( * ) 7 EXIT turns the OSD (On-Screen Display) window off and moves from sub menu to top menu in the OSD window. When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. launches the AUTO TRACKING function directly. When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly. : decreases brightness : increases brightness ( * ) : Hot Key English - 4 English - 5 ADJUSTMENT PROCEDURE OSD FUNCTIONS ICON CONTROL FUNCTION No Is the H.Size proper? Adjust the CLOCK control. LANGUAGE Select language for OSD (6 languages). CLOCK Adjust the width (horizontal size) of the screen image. CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen. AUTO TRACKING Adjust the horizontal & vertical picture image quality and size. Yes Is the noise displayed on the screen? Perform the AUTO POSITION. No Yes Perform the AUTO TRACKING. Choose different preset color temperatures Is the noise displayed on the screen yet? COLOR or set your own customized color TEMPERATURE parameters. No RED CONTROL Adjust the red color. GREEN CONTROL Adjust the green color. BLUE CONTROL Adjust the blue color. H. CENTER & Adjust the position of the display horizontally (left or right) and vertically (up or down). Yes Adjust the CLOCK FINE until the screen is cleared. Yes Is the noise displayed on the screen yet? No End V. CENTER OSD English - 6 SHARPNESS Adjust the display image quality (if the screen proceed to scaling up). OSD POSITION Adjust the OSD position horizontally (left or right) and vertically (up or down). English - 7 SELF DIAGNOSIS ICON CONTROL FUNCTION OSD TIME OUT Adjust the display OSD Menu. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. AUTO POSITION Choose automatically the proper horizontal position and vertical position & size of the screen image. CONTRAST Adjust the contrast of image, the difference between light and dark areas on the screen. If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is No Signal, Out of range or None support . No Signal screen is displayed when the DSub signal connector is not connected or the status of the monitor is on DPMS mode. Out of Range screen is displayed when the applied frequency is under or over normal range. Normal range (Non-interlaced mode only) H : 30 - 80 KHz V : 56 - 77 Hz None support screen is displayed when the applied frequency is under or over factory preset timings. English - 8 English - 9 SPECIFICATIONS Panel Synchronization Video Bandwidth Max Resolution Colors Display Area PC Input Signal AV Input Signal (Option) Size Pixel Pitch Viewing Angle Contrast Ratio Brightness Color Filter Horizontal Vertical Sync Video Video Audio TV Receiving Signal TV Tuner (Option) External Speaker Max. Output (Option) Plug and Play Power Source Power Consumption Dimension-W x H x D 17-inch (43.2 cm) diagonal 0.264 x 0.264 mm 75°(Right/Left) 70°(up), 70°(down) 400:1 contrast ratio (typ) 250cd/m2 brightness (typ) RGB vertical stripe 30 - 80 KHz 56 - 77 Hz 135 MHz 1280 x 1024 a 75Hz 8 bit (16.7M Colors) 337.9mm x 270.3mm H/V separate (TTL) 15 pin mini D-sub(Analog RGB) DVI-D(Option) CVBS(RCA), S-Video(Mini-DIN) RCA Left+Right Input Stereo Mini Jack Input & Output NTSC, PAL Weight-net/gross Power Saving Tilt Range Operating Temperature 6.2/7.6 Kg(13.6/16.7 lbs) EPA, VESA DPMS, Nutek Compliant 5° forward, 30° backward 10 ~ 40°C /50 ~ 104°F The specification can be changed without any prior notice to improve the quality of the product. The LCD panel may have some defective pixels (e.g. slightly light or dark) due to a characteristic of the LCD panel. But there is no defect in your LCD product itself. 6W(Left 3W+Right 3W) VESA DDC Compatible 100-240 Vac, 50/60 Hz (Free Voltage) 40 W 420 x 398 x 194 mm (with stand) 420 x 360 x 68 mm (without stand) English - 10 English - 11 FACTORY PRESET TIMINGS CHANGING THE STAND REMOVING THE STAND VESA MODES Mode VGA Resolution (dots X lines) 640 X 480 a 60Hz H.Freq (KHz) V.Freq (Hz) Remark 31.5 60 Non-interlaced VGA 640 X 480 a 72Hz 37.9 72 Non-interlaced VGA 640 X 480 a 75Hz 37.5 75 Non-interlaced SVGA 800 X 600 a 56Hz 800 X 600 a 60Hz 35.2 56 Non-interlaced 37.9 60 Non-interlaced 48.1 72 Non-interlaced SVGA 800 X 600 a 72Hz 800 X 600 a 75Hz 46.9 75 Non-interlaced XGA 1024 X 768 a 60Hz 48.4 60 Non-interlaced XGA 56.5 70 Non-interlaced 60.0 75 Non-interlaced SXGA 1024 X 768 a 70Hz 1024 X 768 a 75Hz 1280 X 1024 a 60Hz 64.0 60 Non-interlaced SXGA 1280 X 1024 a 75Hz 80.0 75 Non-interlaced SXGA 1152 X 864 a 75Hz 1280 X 960 a 60Hz 67.5 75 Non-interlaced 60.0 60 Non-interlaced SVGA SVGA XGA SXGA IBM MODES EGA Resolution (dots X lines) 640 X 350 a 70Hz DOS 720 X 400 a 70Hz Mode H.Freq (KHz) V.Freq (Hz) 1. Remove 4 screws. 2. Remove the stand REMOVING THE COVER Remark 31.5 70 Non-interlaced 31.3 70 Non-interlaced MAC MODES Mode VGA SVGA SXGA Resolution (dots X lines) 640 X 480 a 67Hz 832 X 624 a 75Hz 1152 X 870 a 75Hz H.Freq (KHz) V.Freq (Hz) Remark 35.0 67 Non-interlaced 49.7 75 Non-interlaced 68.7 75 Non-interlaced THE OTHERS Mode SXGA Resolution (dots X lines) 1280 X 1024 a 70Hz H.Freq (KHz) V.Freq (Hz) 74.4 70 Remark Non-interlaced Remove the Cover. The LCD Monitor has only Non-interlanced modes without flicker. English - 12 English - 13 TROBLESHOOTING ATTACHING THE MONITOR WITH THE ARM-STAND(OPTION) Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card. Tighten 4 screws. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. Use the VESA approved arm-stand. (100x100 mm hole spacing) POWER LED is not Check if power switch is in the on position. lit. Check if the power cord is correctly connected. Image is unstable. Check if the signal cable is suitable to the video card. Image is not centered, too small or too large. Adjust Clock or H&V Center to get the proper image. Picture bounces or a Keep the devices that may cause electrical interference away from the monitor. wave pattern is present in the See the FCC information at the front cover of the picture. manual. Picture is blurred. English - 14 Adjust Contrast and Brightness. English - 15 APPENDIX DESCRIPTION FOR D-SUB CONNECTOR Pin Signal 10 11 12 13 14 15 Red Green Blue GND GND GND-Red GND-Green GND-Blue +5Vdc GND-H.Sync GND-V.Sync Bi-directional Data(SDA) Horizontal Sync Vertical Sync(VCLK) Data Clock(SCL) 10 15 * GND=Ground S/N:9978631900
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:03:05 19:10:24-08:00 Modify Date : 2002:03:05 19:10:24-08:00 Page Count : 12 Creation Date : 2002:03:06 03:10:24Z Mod Date : 2002:03:06 03:10:24Z Producer : Acrobat Distiller 5.0 (Windows) Author : Administrator Metadata Date : 2002:03:06 03:10:24Z Creator : Administrator Title : L700C Users Manual.pdfEXIF Metadata provided by EXIF.tools