Wonde Proud Technology WPSPT10 Tracker User Manual
Wonde Proud Technology Co., Ltd. Tracker Users Manual
Users Manual
WondeX SPT 10 Hardware Quick Installation Guide Version: 1.03 Date: 12/24/2008 WONDE PROUD TECHNOLOGY. General Notes: All materials contained on this documentation is protected by the copyright law and may not be reproduced, transmitted, published or broadcasted without the prior obtaining authorization of Wonde Proud Technology. The documentation is provided for testing, evaluation, integration and product information purpose and it may contain deficiencies or inadequacies information of products. This product is not intended for use in life support appliance, devices or systems where a malfunction of the product can reasonably be expected to result personal injury. Wonde Proud or its supplier will not be liable for any consequential, direct, indirect, incidental, punitive or other damages including without limitation, damages for loss of business profits, business interruption, loss of business information or other pecuniary loss that arising out the use of or inability to use the documentation or product, even if Wonde Proud has been advised of the possibility of such damages. The customers using or reselling the product in such application do so at their own risk and agree to full indemnify Wonde Proud for any damages resulting from illegal use or resale. Subject to change without notice at any time. Copyright Reproduction, dissemination, edition of this document, or utilization of the content and communication format as well as giving to other without authorization are prohibited. Offenders will be held liable for payment of damages. Copyright ©Wonde Proud Technology 2007. All right are reserved. Copyright © Wonde Proud Technology. 2007. All rights are reserved. 2 of 7 WONDE PROUD TECHNOLOGY. Table of Content 1. Safety Instruction: ............................................................................................................................4 2. Introduction of Hardware:................................................................................................................4 3. Insert the SIM Card:.........................................................................................................................4 4. Insert the Backup Battery.................................................................................................................5 5. Connect “USB” Cable......................................................................................................................5 6. LED Indicators:................................................................................................................................6 7. About Wonde Proud Technology: ....................................................................................................7 Copyright © Wonde Proud Technology. 2007. All rights are reserved. 3 of 7 WONDE PROUD TECHNOLOGY. 1. Safety Instruction: Please read below safety instruction carefully before use this device. This device complies with Part 22, 24 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Introduction of Hardware: Mini USB Connector Power Switch SOS Button 3. Insert the SIM Card: Please follow the steps below to insert the SIM Card correctly. a. Unscrew the back cover of device and pull out the lid. b. Uplift the battery (if the battery is connected to the device) c. Unlock the SIM card slot by sliding the holder toward the “OPEN” direction. d. Place the SIM card into the SIM card holder. e. Lock the SIM card slot by sliding the holder toward the “LOCK” direction. f. Then, put back the battery and screw the back cover of the device. Please ensure the SIM card is well placed in the holder and well contacted; otherwise, the device might not detect the SIM card successfully. Copyright © Wonde Proud Technology. 2007. All rights are reserved. 4 of 7 WONDE PROUD TECHNOLOGY. 4. Insert the Backup Battery Please follow the steps below to insert the backup battery correctly. a. Unscrew the back cover of device and pull out the lid. b. Connect the metal side of the battery to socket in the corner and place the battery well. c. Then, put the cover of the device back and screw it well. 5. Connect “USB” Cable USB Cable can be used for the unit configuration or connected to the PC/Car Charger to charge. Notes: 1. Please fully charge the device before further usage after receiving the device. 2. While connecting to the PC to configure the device, please ensure the power button is switched to “on” status. Otherwise, the PC will not recognize the device. Copyright © Wonde Proud Technology. 2007. All rights are reserved. 5 of 7 WONDE PROUD TECHNOLOGY. 6. LED Indicators: - From the Top to the Bottom: GPS, Power, GSM Indicators GPS (Blue) Power (Red) GSM (Green) Status Blinking Behavior power saving Off GPS error 150ms on/150ms off GPS positioning 50ms on/ 450ms off GPS fixed 50ms on/ 2 seconds off power saving 50ms on/ 6 seconds off charging 1 second on/1 second off charging completed On low battery 50ms on/ 450 ms off normal 50ms on/ 2 seconds off power saving Off PIN code error/lock 150ms on/ 150ms off NO SIM Off GPRS connecting 50ms on/ 200ms off/ 50ms on/ 1700ms off normal 50ms on/ 2 seconds off GSM Searching 50ms on/ 450ms off * USB connecting: GPS LED (Blue)/Power LED (Red)/GSM LED (Green): Sequence ON/OFF * As the device is fully charged, the Power LED (Red) will be always in ‘on’ status. Copyright © Wonde Proud Technology. 2007. All rights are reserved. 6 of 7 WONDE PROUD TECHNOLOGY. 7. About Wonde Proud Technology: WondeX SPT10 device is manufactured by Wonde Proud Technology. Wonde Proud Technology provides advanced solution for GPS related solutions including the various GPS components, Automatic Vehicle Location (AVL) device (data logger & real time tracking devices). Please contact us at the phone and fax number list below or visit our website for further product information. Wonde Proud Technology Web site: Tel: Fax: Address: http://www.wondeproud.com +886-2-26968498 +886-2-26968499 4F., No.100,Sec.1,Shin Tai Wu Rd, Sijhih city, Taipei county 22102, Taiwan. R.O.C Copyright © Wonde Proud Technology. 2007. All rights are reserved. 7 of 7 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The highest SAR value for the device as reported to the FCC when worn on the body is 0.549 W/kg for PCS Body SAR. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. This device complies with Part 22, 24 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2009:01:19 11:59:35+08:00 Create Date : 2008:12:24 10:59:54+08:00 Metadata Date : 2009:01:19 11:59:35+08:00 Format : application/pdf Title : Microsoft Word - SPT10 Hardware Installation Guide103 .doc Creator : user Document ID : uuid:a2d45202-319f-482b-90ef-949d4a8ab6b6 Instance ID : uuid:7e75b632-e054-4691-8812-b59ed4e79059 Page Count : 8 Author : userEXIF Metadata provided by EXIF.tools