Zhongshan K mate General Electronics BTH132 Bluetooth Stereo Headset User Manual BTH132 User s Manual
Zhongshan K-mate General Electronics Co., Ltd Bluetooth Stereo Headset BTH132 User s Manual
User manual
BTH132 Bluetooth stereo headset User’s manual Contents Brief introduction…………...…………………………..…....1 Before use……………………………………………………..1 1. Overview…………………………………………………...……1 2. Charging for headset..……………………………………………2 Getting started……..…………………………………………3 1. Turning on/off the headset…………....……………………......3 2. Wearing the headset.......................................................................3 3. Pairing/connecting…….……..............................……………..….4 1) Pairing headset with Bluetooth cell phone via Bluetooth……..….4 2) Pairing headset with a Bluetooth transmitter via Bluetooth……5 3) Pairing headset with multi devices via Bluetooth ….............…....5 4. Battery display..............................................................................6 5. Making a call with the headset………………………………...….6 6. Playing music………………………………………………….....9 7. LED indicator…………………………………………………....9 8. Factory Reset………………………………………………..….10 Care and maintenance……………………………..………..10 FAQs……………………………………...…………………..11 Specification……………………………...………………..…11 Welcome to use this Bluetooth stereo headset, BTH132. Please read this user’s manual carefully before use. Brief introduction BTH132 is Bluetooth stereo headset suits for sports. With two battery for long working. You can use it to enjoy wireless music and make a call at the same time. Before use 1. Overview 1 Adjustable stabilizer Cable management Microphone Multi-functions button volume up/next track Charging jack volume down/last track Four different size eartips LED indicator 2. Charging for headset When the headset is low power, the headset emits “Battery low” once every 2 minutes and the red Led flashes instead of blue LED. Please recharge the battery of the headset. The way of charging as following: Using USB cable 1. Turn on the cover of charging jack, and plug the USB charging cable 2. Plug another side of cable to the USB port of PC Red light on: Charging Red light off: Finish charging 3. It will takes about 1.9 hours to finish charging Remarks: 1) The battery is recyclable. 2) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire or the like. Getting started 1. Turning on/off the headset Functions Operation Prompt tone Turning on Press and hold button about Power on 3 seconds until blue LED flashes Turning off Press and hold button Power off about 3 seconds until red LED flashes Remark: In order to save power, the headset will turn off automatically if no devices can be connected for long time. 2. Wearing the headset a. Choose the suitable size eartips according to your ear and wear as following shown: b. Wearing headset as below picture to fix headset on ear. c. The ear-hook can be bending adjust in multi-angle to get suitable wearing effect. Do not put the ear-hook in half or it will be damaged. d. The cable management can be use to buckle long line so that wearing headset more steady. e. You can also fix the headset as a necklace with the cable management. It is convenient and beautiful. 3. Pairing/connecting 1) Pairing headset with Bluetooth cell phone via Bluetooth Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone user’s manual for further information. The general pairing procedures are as follows: 1) Keep your headset turned off and within 1 meter of phone ; about 5 seconds until the red and blue LED flash 2) Press and hold alternately, the headset enter into paring mode and emits “pairing” 3) Activate your cell phone’s Bluetooth function and search for Bluetooth devices within range, select “BTH132” from the list of devices shown 4) After successful connecting, blue LED of headset flashes twice every 4 seconds and emits “Your headset is connected” Remarks: Pairing mode will last 2 minutes, the headset will back to standby mode if the pairing failure. If the pairing is not successful, turn off the headset and repeat the steps as above. After successful pairing, the headset will connect to the last connected device automatically. When the headset is in standby mode and not connect with device, short press any button of headset, it will try to connect to last connected device. If disconnect from the device,the headset will emits”Your headset is disconnected”. When the headset is out of effective range and not connected with device, the headset emits “Out of range”, it will automatically connected after back to effective arrange in 5 minutes. If overtime, short press any button, it will connected again. 2) Pairing the headset with a Bluetooth transmitter via Bluetooth You can connect the headset to a Bluetooth transmitter to enjoy music wirelessly. Hereby take BTT005 (Bluetooth transmitter, not included in accessories) for example. The pairing steps are as follows: 1) Keep your headset and transmitter within 1 meter when pairing; 2) Make the headset enter pairing mode (Please refer to “How to enter pairing mode); 3) Turn on the Bluetooth transmitter and make it enter paring mode. It will search for Bluetooth devices automatically; 4) After successful pairing and connecting, blue LED of the headset flashes twice every 4 seconds and emits “du” tone. Remarks: If pairing still fails after several tries, please refer to the Bluetooth transmitter’s user’s manual for further information. 3)Pairing headset with multi devices via Bluetooth The headset can connect with two Bluetooth cell phones at the same time. The general pairing procedures are as follows: 1) Pairing the headset with device one 2) Turn on the headset and make it enter pairing mode again, and pairing it with device two 3) Operate device one to connect with headset. The headset has already connected with two devices in this moment . Restart the headset, it will also connected with two devices automatically. Remarks: and button under standby mode(not connected Turn on: long press device), and release it until you hear “Enable multipoint” and button under standby mode(not connected Turn off: long press device), and release it until you hear “Disable multipoint” To improve the stabilization of headset, we suggest you turn off the multi-pair function when you only connect with one cell phone. 4. Battery display When the headset connected with IOS device, it will display the battery of the headset on the device. When the headset is in low battery, power symbol show red, it emits you to charge for your headset. Full battery Low battery 5. Making a call with the headset 1) Basic operation Functions Status of headset Cancel a call Calling Answer a call Incoming ringing Operation Short press once Short press once call Prompt tone Call terminated Answer Reject a call End a call Incoming call ringing During a call Volume up During a call Volume down During a call Transfer conversation to mobile phone Transfer conversation to headset Microphone mute Cancel mute During a call Long press about 2 seconds During a call Long press about 2 seconds During a call Long press about 2 seconds Long press about 2 seconds Voice dial Long press about 2 seconds Short press once Short press button Short press button During a call (microphone mute) Connected device) Reject Call terminated No prompt tone No prompt tone Transfer audio Transfer audio Mute on Mute off Short press button Voice dial and simultaneously Redial the Connected Double click Last number last number device) button redial Warning: Excessive pressure from earphones and headphones can cause hearing loss. Note: To get the best calling effect make your microphone closer to your mouth. When the volume is adjusted to max or min, you will hear one prompt tone. When the headset under microphone mute mode, you will hear two tone “DuDu” continuously every 10 seconds. When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone. You can switch the call to the headset by using the conversation switch button or through operating on the mobile phone. Please refer to your mobile phone user manual for further information. 2) Three-ways call operation Functions Status of headsets Answer new call and There are second end current call incoming call Answer new call and There are second retain current call incoming call Switch calls Keep conversation End current call and switch retain call Keep conversation Operation Short press once Double click button Double click button Short press once 3) Connect with two cell phones Functions Status of headset End phone call #1 During phone call #1, and answer phone phone 2 has incoming call #2 call Retain phone call #1 During phone call #1, and answer phone phone 2 has incoming call #2 call Switch call During call, one of phone call is retained End current call, During call, one of back to retain phone phone call is retained call 6. Playing music Functions Volume up Volume down Last song Next song Pause play Status of the headset Playing music Playing music Playing music Playing music Playing music Pausing Operation Short press Double button once click Double click button Short press once Operation Short press button Short press button Long press button Long press button Short press once Short press once Notes: When the volume is adjusted to max, you will hear “ maximum volume”. When the volume is adjusted to min , you will hear prompt tone “Du” If you want to remote control last/next song, pause/play, it needs your Bluetooth mobile phone or Bluetooth transmitter paired with the headset to support AVRCP profile, please refer to the user’s manual of your mobile phone or Bluetooth transmitter for further information. 7. LED indicator LED indicator Red and blue LED flashes alternately Blue LED flashes once every 2 seconds Blue LED flashes twice every 4 seconds Red LED flashes instead of blue LED 10 Status of headset Pairing mode Not connected to device Connected to device Low battery 8. Factory Reset button about 3 seconds and release it In the status of charging, long press until the red and blue LED flashes simultaneously, you will hear 2 prompt tone “reset paired device list” Remarks: After factory reset, the paired list of headset will be deleted. After turn it on again, the headset will enter pairing mode automatically, and you need to re-pair and connect with Bluetooth devices. Care and maintenance Read the following recommendations carefully before using BTH132. Following these you will be able to enjoy this product for many years. Please note that the cord management clips are optional accessory for better wearing. Keep it dry and don’t put it in the dump place to avoid the product’s internal circuit being affected. Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts. Don’t expose the product to cold areas. It may damage the internal circuit board. Don’t try to disassemble the product as it may get damaged if you are not professional. Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged. Don’t use intensive chemical products or detergent to clean the product. Don’t scratch the surface with sharp things. Don’t use this product during strenuous exercise. It may get damaged by sweat. In case the product doesn’t function properly, send it to the store you bought it. The staff will help you to solve the problem 11 FAQs 1.What does it mean when red LED flashes instead of blue LED? Battery is low power, need to be recharged. 2.Why is the red LED off when charging? a) Please make sure the charging device connect with headset well; b) The battery may dry up. Please charge the battery for 30 minutes, and then the red LED will be ON. 3. Why can’t I hear the sound on the headset? c) Make sure the headset has been switched on; d) Make sure the volume is not too low or muted; e) Make sure the headset connects with the mobile phone correctly; f) Make sure the distance between the headset and the cell phone is in the available Bluetooth range. 4. Why can’t I hear the sound clearly on the headset? a) Make sure the mobile phone is in the strong signal area; b) Make sure the headset is in the available range of this product. 5. Why the pause/play, last/next song not function when playing music? Make sure your Bluetooth device supports AVRCP (Audio/Video Remote Control profile) Specifications Bluetooth version Bluetooth profiles Operating distance Headset music time Headset talk time Standby time Headset charging time Charging input Weight Measure Bluetooth V4.1 HFP, HSP, A2DP and AVRCP 10 meters Up to 14 hours UP to 15 hours About 500 hours About 1.9 hours DC 5.0V /500mA About 15 g Remote control:42.55*8.66*7.84mm Headset:28.84*17.04*21.23mm 12 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Administrator Create Date : 2017:09:15 16:43:10+08:00 Modify Date : 2017:09:15 16:43:10+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : Microsoft Word - BTH132 User's Manual Creator : Administrator Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:42253ab7-188a-4cd8-bace-3eb20731326f Instance ID : uuid:5b29f84e-ba5d-4814-85b5-1d846a039490 Page Count : 15EXIF Metadata provided by EXIF.tools