3M Cogent ACD100P-CB Philips card reader User Manual Mini Gate ACD100P CB

3M Cogent, Inc. Philips card reader Mini Gate ACD100P CB

User Manual

EthernetRS485PowerWiegandRelayType No Name Color12345678910111213141718192021222324252627YellowOrangeBlackBrownPurpleBlackWhiteGreenYellow&GreenBlackBlueGrayBlackRedBlueGreenWhiteYellow7 PIN_Female_ConnectorRelay 12V+Relay-GND(Relay GND)Wiegand_In_D1/LED_InputWiegand_In_D0GND(Wiegand GND)Wiegand_Out_D1Wiegand_Out_D0P_GND(Safety GND)GND(RS485 GND)RS485+RS485-GND(Power GND)Power_In(12V)RX-RX+TX-TX+UART For GPRS Module13 4 8 9 14 15 20l ：l ：l Memory：128 MB DDR/ 128MB Flashl Expansion Memory：Micro SD(2GB for default configuration)l LCD Display：1.8" TFT Color LCDl LED Indicator： Multi-color × 3l Keypad：3 X 5 keypadl Audio：Beepl PC Port：USB2.0l Built-in Relay Control: 1l Power supply：12V DC/1.5A l Current：450mA @ 12Vl Operating Temperature：0 ~ 45˚ Cl Storage Temperature：0 ~ 45˚ Cl Fingerprint Sensor：Cogent CSD100, 500dpi Optical Sensor, (FBI Certified)l Matching Speed：1:1 ≤1.2s，1:N ≤2s (N≤5000)l FRR：1%l FAR：0.001%l Matching Security Grade：Lower, Middle, High (Configurable)l Acceptable Fingerprint Rotation：+/-15 degree (Default)Model ACD100P-CBProcessor SAM9G45@400MHz, ProcessorLCDLED Key PadUSB PortReset BottonSpeaker Fingerprint SensorContactless Card Area( Part is for RF Reading Area)Keypad Card L spanner 11List Quantity1114+21111Mini-Gate biometric access controlFixing board A (plastic)Fixing board B (plastic)Screw （PM4X5）Screw（PWM3X5）DC12V Power ConnectorRJ45 Network Port ConnectorMini-Gate User ManualPower Adapter（DC 12V/1.5A）Introduction for Function and Technical DataMini-Gate User ManualAddress : 10/F，Tinwe Industrial Park Phase 2, Liufang Road No.6, Area No.67, Baoan District, ShenZhenTel ：+ 86 - 755 - 86013579 Fax：+ 86 - 755 - 86013575Step 1 Step 2Step 1: Step 2: Step 3: Screw stainless steel plate according to the 4 holes marked on the drawing,choose right size of screws by different wallsInsert installing device aimed to stainless steel plate.Fasten this screw on the bottom.Step 3Step 1: Cassette（86*86）Step 2: Screw fixing board to cassette, choose the right size of screws by different cassettes.Step 3: Cover the fixing board.Step 4: Screw stainless steel plate to fixing board, then install device on the stainless steel plate.Option 1 : On wall directlyStep 1 Step 2 Step 3 Step 4Option 2 : The cassette (86x86) on wallDevice Installation Guide2Screw（FM 2X6）
Module and Function GuideTime SettingLightness SettingNetwork SettingOK Add Administrator模式选择Fingerprint + Card + PIN ModeFingerprint ModeFingerprint + Card ModeCard + PIN ModeFor identify, select this mode.fingerprint + card For identify, select this mode.card + pin For fingerprint identify, select this mode. For identify, select this mode.fingerprint + card + pin Administrator Settingand User SettingMode SettingOK OK OK OK Standard Mode Advanced ModeDelete UserAdd UserDeleteAdministratorNote: Factory Default: Administrator user ID:"1"; Pin #:"1". This will be invalid after new admin setup."User setting" should be changed to "admin setting"网络设置OK OKOK OKOK OKOK OK
FCCStatements changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for Remark: 1 USB port is used to firmware upgrade purpose, without loading. 2 This device is installed on the wall. And the all the ports are in the wall. People can’t touch. 3 CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

Navigation menu