3M 300cf 300cf, Type 29800 User Manual To The 10470027 Bf23 4667 Be4d 3f4872ec4f1b

User Manual: 3M 300cf to the manual

Open the PDF directly: View PDF .
Page Count: 41

3M Packaging Systems Division

3M Center, Building 220-8W-01

St. Paul, MN 55144-1000

Serial No.

For reference, record machine serial number here.

Printed in U.S.A.

"3M-Matic" is a Trademark of 3M,

St. Paul, MN 55144-1000

Type 29800

For Use With 3M-Matic™:

100a Type 29600, 120a Type 19700,

120a3 Type 19700, 120ab Type 19700,

200a Type 39600, 700a Type 39600,

800a Type 39600, 800a3 Type 39600,

800ab Type 39600 Case Sealers

Note: The 300cf is not compatible with the Low

Tape Sensor Kit or outboard tape roll mounting

Read "Important Safeguards",

pages 3 and 4, BEFORE

INSTALLING OR

OPERATING THIS

EQUIPMENT.

Important Safety

Information

Instructions and Parts List

300cf

Case Former

3M-Matic™

Replacement Parts and Service Information

3M Packaging Systems Division

3M Center, Building 220-8W-01

St. Paul, MN 55144-1000

To Our Customers:

This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you

ordered. It has been set up and tested in the factory with "Scotch" brand

tapes. If technical assistance or replacement parts are needed, call or Fax

the appropriate number listed below.

Replacement Parts

Order parts by part number, part description and quantity required. Also

include machine name, number and type. A parts order form is provided at

the back of this manual.

3M/Tape Dispenser Parts

241 Venture Drive 1-800/344 9883

Amery, WI 54001-1325 FAX# 715/268 8153

Technical Assistance

3M-Matic™ Helpline – 1-800/328 1390. Please provide the customer support

coordinator with the machine number, machine type/model and serial number.

If you have a technical question that does not require an immediate response,

you may Fax it to 715/381 0248.

Minimum billing on parts orders will be $25.00. Replacement part prices available on request.

Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information.

$10.00 restocking charge per invoice on returned parts.

"3M-Matic", "AccuGlide" and “Scotch” are trademarks

of 3M, St. Paul, Minnesota 55144-1000

Printed in U.S.A.

Replacement Parts And Service Information

To Our Customers:

This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you

ordered. It has been set up and tested in the factory with "Scotch" brand

tapes. If any problems occur when operating this equipment, and you

desire a service call, or phone consultation, call, write or Fax the

appropriate number listed below.

SERVICE AND PARTS AVAILABLE DIRECT FROM:

Order parts by part number, part description and quantity required. Also include

machine name, number and type.

1-800/328 1390

"3M-Matic", "AccuGlide" and “Scotch” are trademarks

of 3M, St. Paul, Minnesota 55144-1000

Printed in U.S.A.

3M Packaging Systems Division

3M Center, Building 220-8W-01

St. Paul, MN 55144-1000

Instruction Manual

300cf Case Former

Type 29800

Table of Contents Page

Intended Use..................................................................................................................................... 1

Equipment Warranty and Limited Remedy ....................................................................................... 2

Contents............................................................................................................................................ 2

Important Safeguards ....................................................................................................................... 3 - 4

Specifications ............................................................................................................................. 5 - 6

Air Power Requirements .................................................................................. 5

Box Board ......................................................................................................... 5

Box Weight and Size Capacities ...................................................................... 5

Operating Conditions........................................................................................ 5

Machine Dimensions ........................................................................................ 6

Installation and Set-Up ..................................................................................................................... 7 - 9

Receiving and Handling ................................................................................... 7

Machine Set-Up ................................................................................................ 7 - 9

Operation .......................................................................................................................................... 11 - 14

Manual/Automatic Mode................................................................................... 12

Emergency Stop Button ................................................................................... 13

Reset Button ..................................................................................................... 13

Box Centering Guides ...................................................................................... 13

Box Ejector ....................................................................................................... 13

Manual Operating Procedure ........................................................................... 13

Automatic Operating Procedure ....................................................................... 14

Maintenance ..................................................................................................................................... 15

Cleaning of the Machine................................................................................... 15

Lubrication ........................................................................................................ 15

Pneumatic Diagram .......................................................................................................................... 16 - 17

Parts and Service Information .......................................................................................................... 19

Replacement Parts Illustrations and Parts List................................................................................. 21 - 37

Intended Use

The 3M-MaticTM 300cf Case Former has been designed and tested for use with the following 3M-Matic™ case

sealers:100a, 120a, 120a3, 120ab, 200a, 700a, 800a, 800a3 and 800ab. A regular slotted carton is placed on

the center rail of the case former and the bottom side flaps are automatically closed by the machine. A pneumatic

device pushes the carton into the case sealer for bottom sealing of the carton.

3M-MaticTM 300cf Case Former, Model 29800 (Shown installed with 800a Case Sealer).

Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR

PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR

USAGE OF TRADE:

3M warrants that its 3M-Matic™ 300cf Case Former, Type 29800 will be free from defects for ninety (90) days

after delivery. If any part is proved to be defective within the warranty period, then the exclusive remedy and

3M’s and seller’s sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part

is returned immediately to 3M’s factory or an authorized service station designated by 3M. A part will be

presumed to have become defective after the warranty period unless the part is received or 3M is notified of the

problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part

within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price. 3M shall

have no obligation to provide or pay for the labor required to install the repaired or replacement part. 3M shall

have no obligation to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any

accidental cause other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning,

improper operating environment, improper utilities or operator error.

Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential

damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.

The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a

written agreement signed by authorized officers of 3M and seller.

"3M-Matic" is a trademark of 3M, St. Paul, MN 55144-1000

(1) 300cf Case Former, Type 29800

(1) Tool/Spare Parts Kit, P/N 78-8111-1356-8

(1) Instruction and Parts Manual

Contents – 300cf Case Former

Important – In the event the following safety

labels are damaged or destroyed, they must

be replaced to ensure operator safety. A

label kit, part number 78-8119-6942-3 is

available as a stock item or individual labels

can be ordered. See Parts Illustration/List,

pages 36 and 37.

Important Safeguards

This safety alert symbol identifies

important safety messages in this

manual. READ AND UNDERSTAND THEM

BEFORE INSTALLING OR OPERATING

THIS EQUIPMENT.

The "Warning – Air Pressure" label, shown in

Figure 1-1, is attached next to the return stroke air

pressure regulator. The regulator is located behind

the pneumatic compartment cover and is factory

adjusted. No operator adjustment is required.

Figure 1-1 – Air Pressure Warning Label

The "Re-Set" label, shown in Figure 1-3, is

attached to the top of the adjustable carton ejector

next to the "Reset"push-button. The "Reset" push-

button must be pushed to restore air supply after

stopping machine with E-Stop switch.

Figure 1-2 – Emergency Stop Label

The "Emergency Stop" label, shown in Figure 1-2,

is attached to the top of the adjustable carton ejector

assembly around the E-Stop push-button. The label

reminds operators and casual personnel of the

function of this switch.

Figure 1-3 – Reset Label

Important Safeguards (Continued)

The "Operation Mode" label, shown in Figure 1-6 is

attached on the left side of the machine frame below

the Manual/Automatic switch. The label indicates

the correct position of the switch for manual or

automatic operation.

The "Ram Adjust" and "Box Ejector" labels,

shown in Figure 1-7 are attached to the top of the

adjustable carton ejector. The labels remind

operators of the function of the push-button switch

and the adjustment detent knob.

Figure 1-46– Operation Mode Label

Figure 1-7 – Ram Adjust and Box Ejector Labels

Figure 1-4 – Safety Instructions Label

Figure 1-5 – Air On/Off Label

The "Air Pressure – On/Off" label, shown in

Figure 1-5, is attached on the left side of the

machine frame above the On/Off valve. The label

reminds operators of the location of the pneumatic

On/Off valve,

The "Safety Instructions label, shown in

Figure 1-4, is attached on the left side of the

machine frame. The label provides convenient

safeguard instructions for the operator and service

personnel.

IMPORTANT SAFEGUARD

Specifications

Air Power Requirements

517 kPa minimum gauge pressure, 6.0 m3/h @ 21°C, 101 kPa maximum at maximum cycle rate [75 PSIG

minimum gauge pressure, 3.5 SCFM maximum at maximum random cycle rate]. A pressure regulator-filter is

included. For best operation set pressure regulator to 90 PSIG.

Box Board

125 to 275 P.S.I. bursting test, single wall B, or C flute.

Boxes should be well scored for proper performance.

Box Weight and Size Capacities

A. Box weight, filled – 2.3 kg [5 lbs] minimum to 37 kg [80 lbs] maximum.

B . Sizes: Minimum Maximum

Length 205 mm [8.0 inch] 600 mm [23.5 inch]

Width 205 mm [8.0 inch] 545 mm [21.5 inch]

Height 100 mm [4.0 inch] limited by case sealer

Note: The box size capacities for the 300cf may be limited by the capacity of the case sealer in some

instances.

Operating Conditions

Use in dry, relatively clean environments at 5° to 40° C [40° to 105° F] with clean dry boxes.

Note –Machine should not be washed down or subjected to conditions causing moisture condensation on

components.

(Specifications continued on next page.)

Specifications (Continued)

Machine Dimensions

A1H12H22L13,5 L24,5 W1 W2

Minimum

mm 120 610 685 1375 1385 615 765

[Inches] [4.81] [24.0] [27.0] [54.1] [54.6] [24.3] [30.2]

Maximum

mm 120 775 850 1705 1715 615 765

[Inches] [4.81] [30.5] [33.5] [67.1] [67.6] [24.3] [30.2]

1 Casters are optional

2 Includes the height of a plastic foot which is removed if casters are used.

3 L1 is 300cf Case Former connected to 120a, 120a3

4 L2 is 300cf Case Former connected to 100a, 200a, 700a, 800a, 800a3

5 Add 30 mm to these dimensions when connecting to a 120ab or 800ab

Weight – Approximate 86 kg [190 pounds] crated (approximate)

Approximate 75 kg [165 pounds] uncrated (approximate)

Receiving And Handling

For future reference, record machine serial number

on front cover of this manual in the space provided.

The following instructions are presented in the order

recommended for setting up and installing the

case former, as well as for learning the operating

functions and adjustments. Following them step by

step will result in your understanding of the machine

and an installation in your production line that best

utilizes the many features built into the case former.

Refer to Figure 3-1 to identify the various

components of the case former.

After the machine has been uncrated, examine the

case former for damage that might have occurred

during transit. If damage is evident, file a damage

claim immediately with the transportation company

and also notify your 3M Representative.

Figure 2-1 – Bed Height Adjustment

Installation and Set-Up

Machine Set-Up

Important – Read "Warnings", on page 12,

before attempting to set up the case former

for operation.

Note – A tool kit consisting of metric open end

and hex socket wrenches is provided with the

machine. These tools should be adequate to set

up the machine, however, other tools supplied by

the customer will be required for machine

maintenance.

1. Follow "Unpacking Instructions" label attached

to corrugated packing cover.

Use appropriate material handling equipment to

remove the machine from the pallet and move it

into position.

Whenever the machine is lifted with a fork truck,

insure that the forks span completely across the

machine frame and do not contact any

mechanism under the machine frame.

Refer to Figure 2-1 and adjust the bed height as

follows:

(a) Block up the machine frame to allow

adequate leg adjustment.

(b) Loosen, but do not remove, two M8 x 16

mm socket screws in one leg. Adjust

the leg length for the desired bed height.

Retighten the two screws to secure the

leg. Adjust all four legs equally.

3. Install case former in production line.

Refer to Figure 2-2 for installation set up. Case

former bed must be level and equal or slightly

higher than case sealer bed height.

Install mounting brackets as shown in

Figure 2-2.

2. Adjust machine bed height.

The case former is equipped with four adjustable

legs that are located at the corners of the frame.

The legs can be adjusted to obtain different

conveyor bed heights from 610 mm [24.0 inch]

minimum to 775 mm [30.5 inch] maximum.

CAUTION – Machine weighs

approximately 85 kg ]190 lbs]

uncrated.

Installation and Set-Up (Continued)

Figure 2-2 – Mounting Bracket Installation

Installation and Set-Up (Continued)

4. Pneumatic Connection

The case former requires a 5.2 bar gauge

pressure [75 PSIG], 6.0 m3/h @ 21°C, 1.01 bar

[3.5 SCFM] compressed air supply.

The customer supplied air supply hose should

be connected to the barbed fitting on the On/Off

valve and clamped tightly with the hose clamp

provided. See Figure 2-3. Shut the air valve off

and connect the air line. Turn the On/Off valve

On (SUP), to energize the pneumatic

components.

If another type of connector is desired, the

barbed fitting and/or elbow can be removed and

replaced with the desired connector. The air

On/Off valve inlet is 1/4-18 standard pipe

threads.

5. Side Guide Extensions

Under certain circumstances, the centering

guides may interfere with the side guides on the

100a, 200a or 700a case sealers. If this occurs,

the case sealer side guides can be removed and

centering guide extensions can be installed on

the 300cf Case Former. The side guide

extensions are included with the 300cf. Install

guides as shown in Figure 2-4.

6. After completing the "Installation and Set-Up"

procedure, continue through "Operation" to be

sure case former is properly set-up to run boxes.

Figure 2-3 – Pneumatic Connections

Figure 2-4 – Side Guide Extensions

THIS PAGE IS BLANK

Operation

Figure 3-1 – 300cf Case Former Components

IMPORTANT – Before operating the case former, read the "Important Safeguards", pages 3-4 and

"Warnings" on page 12 as well as all of the "Operation" instructions.

Refer to Figure 3-1 to acquaint yourself with the various components and controls of the case former.

Operation (Continued)

Figure 3-2 – Adjustable Carton Ejector

WARNINGS

1. Turn air supply off before performing any adjustments or maintenance on the machine.

2. Turn air supply off when machine is not in use.

3. The case former contains flap folders and sliding components that operate in rapid succes-

sion. Keep hands out of this area when machine is in operation.

4. Failure to comply with these warnings could result in severe personal injury and/or equip-

ment damage.

Manual/Automatic Mode

The operator can control the box movement from the

case former to the case sealer by the manual/

automatic mode switch located on the left side of the

frame. Figure 3-1.

In the manual mode, (for top and bottom taping) the

operator must press the ejector button (Figure 3-2)

to cause the ejector to move the box forward into the

case sealer.

In the automatic mode, (for bottom taping only) the

box is moved forward by the ejector without operator

assistance.

Operation (Continued)

Emergency Stop Button

The E-Stop button can be pushed at any time to

stop machine operation and bleed air from the

pneumatic system.

Reset Button

When case former is stopped with E-Stop, the Reset

Button must be pushed to restore air supply to the

machine.

Box Centering Guide

The four knobs for locking the centering guides in

position are located at the front and rear of the

machine. Center the box in the machine with the

centering guides and tighten the knobs to lock

guides in place.

Box Ejector

The ejector and air cylinder are located on the top

center rail of the case former as shown in Figure 3-2.

The ejector is adjustable along the rail in 25 mm

[1 inch] increments to accommodate box lengths

from 205 mm [8 inch] minimum to 600 [23-1/2 inch]

maximum.

Manual Operating Procedure

(Top and Bottom Taping)

Refer to Figures 3-2 and 3-3

1. Turn case former air valve "On" (SUP).

2. Turn Manual/Auto valve to "Man".

3. Hold the empty box over the center rail. Fold

the front bottom flap on the rail and rear bottom

flap on the carton ejector.

4. Move box forward (toward case sealer) until

both side bottom flaps contact the bottom flap

actuator plates. The two bed plates will then

rotate up and fold the side box flaps up.

Figure 3-3 – Box Placement

5. Fill the box with product.

6. Close box top flaps, front and rear and then side

flaps.

7. While holding top flaps down, press "Eject"

button to move box into case sealer. Hold top

flaps down until box moves into case sealer.

The ejector will return to the rest position and

the bed plates will return to full open position

ready for the next box.

Operation (Continued)

Automatic Operating Procedure

(Bottom Taping Only)

1. Raise case sealer upper taping head to

maximum height (if applicable).

2. Turn case former air valve "On" (SUP).

3. Turn Manual/Auto valve to "Auto".

4. Place open box with front and back bottom flaps

folded in, onto the case former center rail.

5. Move box forward (toward case sealer) until

both side bottom flaps contact the bottom flap

actuator plates. The two bed plates will then

rotate up and fold the side box flaps up.

The box ejector will automatically push the box

into the case sealer and then return to the rest

position ready for the next box.

Maintenance

Note – Never attempt to remove dirt from

machine by blowing it off with compressed air.

This can cause dirt to be blown into critical

machine components and cause premature wear.

Never wash down or subject machine to

conditions causing moisture condensation as

serious equipment damage could result.

Regular slotted containers produce a great deal of

dust and paper chips when processed or handled in

equipment. If this dust is allowed to build-up on

machine components, it can cause component wear.

The dust build-up can best be removed from the

machine by a shop vacuum. Depending on the

number and type of boxes used in the case former,

this cleaning should be done approximately once per

month. If the boxes are dirty, or if the environment in

which the machine operates is dusty, cleaning on a

more frequent basis may be necessary. Excessive

dirt build-up that cannot be removed by vacuuming

should be wiped off with a damp cloth.

Cleaning of the Machine

Note – Wipe off excess oil and grease. It will

attract dust which can cause premature equip-

ment wear and jamming.

Lubrication

The Lubrication Chart shown in Figure 4-1 illustrates

the frame points which should be lubricated every

250 hours of operation. Lubricate the rotating and

pivoting points noted by the arrows with SAE #30

non-detergent oil.

WARNING – Disconnect air

supply to the machine before

beginning any maintenance, Failure to

do so could result in personnel injury

or damage to the machine.

Figure 4-1 – Lubrication Chart

Description (Parts Drawing Reference/Item Number) Lubricant Instructions

Chain (Ref. No. 5422-9 & 5422-10) 2 Lightly coat chain

Sliding Block – Ejector Guide (Ref. No. 5424-13) 1 Lightly coat guide slots

Sliding Block – L/H (Ref. No. 5424-14) 1 Lightly coat guide slots

Sliding – Flap Folder (Ref. No. 5424-27) 1 Lightly coat guide slots

Lubricant 1. White Moly Grease With Liquilon, Plate Master #177L

2. NLGI Grade 2 Multi-purpose Film Forming With Liquilon, Polymere #400

Pneumatic Diagram

On/Off Valve: SMC EVHS2500

Filter-Regulator: SMC EAW2000

Shuttle Valves: SMC EVZA5220

Roller Valves: Telemecanique PXC-M52

Flow Controls 1 and 2: Legris 7665-56-11

Pressure Regulator 2: SMC EAR111

Manual-Auto Select Valve: Telemecanique PXB-B1011BA2

Flow Control Valves

3 and 4: Legris 7665-56-14

Sensor Valves: Legris PWS-P

Bottom Side Flap

Cylinders: SMC C65B32-125C-Y2-*

Ejector Cylinder: SMC C65B40-500C-Y37-*

OR Valve: Telemecanique PLK-A11

Box Ejector Valve: Telemecanique PXB-B191

Figure 5-1 – Pneumatic Diagram

THIS PAGE IS BLANK

Parts and Service Information

Labels

In the event that any labels are damaged or destroyed, they must be replaced to ensure operator safety. A

label kit, part number 78-8119-6942-3 is available as a stock item. It contains all the safety labels used on the

300cf Case Former or separate labels can be ordered from the parts list, page 37.

Replacement Parts Ordering Information and Service

Refer to the first page of this instruction manual "Replacement Parts and Service Information".

THIS PAGE IS BLANK

Replacement Parts Illustrations and Parts List

300cf Case Former, Type 29800

Frame Assemblies

1. Refer to first illustration, Frame Assemblies, for the figure number that identifies a specific portion of the

machine.

2. Refer to the Figure or Figures to determine the individual parts required and the parts reference number.

3. The replacement parts list that follows each illustration, includes the part number and part description for the

parts in that illustration.

Note – The complete description has been included for standard fasteners and some commercially

available components. This has been done to allow obtaining these standard parts locally, should the

customer elect to do so.

4. Order parts by part number, part description and quantity required. Also include machine name, number and

type.

5. Refer to first page of this instruction manual for parts ordering address and/or fax number.

IMPORTANT – Not all the parts listed are normally stocked items. Some parts or assemblies

shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm

item availability.

THIS PAGE IS BLANK

Frame Assemblies

300cf Case Former

Figure 5420

300cf Case Former

Figure 5420

Ref. No. 3M Part No. Description

5420-1 78-8119-6529-8 Conveyor – Bed, W/English Language Label

5420-2 78-8100-0914-8 Leg Assembly

5420-3 78-8100-0915-5 Leg – Outer

5420-4 78-8100-0916-3 Leg – Inner

5420-5 78-8060-8480-8 Pad – Foot

5420-6 78-8055-0867-4 Screw – Hex Hd – M8 x 30

5420-7 78-8017-9318-9 Washer – Plain, 8 mm

5420-8 78-8017-9313-0 Nut – Self-Locking, M8

5420-9 78-8052-6677-8 Clamp – Inner

5420-10 78-8052-6676-0 Clamp – Outer

5420-11 26-1003-7963-0 Screw – Soc Hd, M8 x 16

5420-12 78-8100-0917-1 Label – Leg

5420-13 26-1003-7964-8 Screw – Soc Hd Hex Soc Dr, M8 x 20

5420-14 78-8100-0918-9 Reinforcement

5420-15 26-1003-7943-2 Screw – Soc Hd, M4 x 12

5420-16 78-8005-5740-3 Washer – Plain, 4 mm

5420-17 78-8010-7416-8 Nut – Hex, M4

5420-18 78-8114-4982-2 Plate – Reinforcement

5420-19 78-8010-7169-3 Screw – Hex Hd, M6 x 12

5420-21 78-8100-0920-5 Cover – Front

5420-22 78-8032-0375-7 Screw – Hex Hd, M6 x 16

5420-23 78-8042-2919-9 Washer – Triple, M6

5420-24 78-8100-0922-1 Support

5420-25 78-8100-0921-3 Cover

5420-26 26-1003-7957-2 Screw – Soc Hd Hex Hd, M6 x 16

5420-27 78-8100-0923-9 Grommet

5420-28 78-8094-6489-0 Snap Bushing – SB 1250-15

5420-29 78-8114-4703-2 End Cap – /25 x 1.2

5420-30 78-8094-6177-1 Cap

5420-31 78-8076-4535-9 Bracket

5420-32 78-8094-6305-8 Plate – Gauge

5420-33 78-8060-8087-1 Screw – M5 x 10

5420-34 78-8098-9076-3 Caster Assembly

5420-35 26-1009-9096-4 Caster – Dual Locking

5420-36 26-1009-9094-9 Washer – Spring Helical, M12

5420-37 26-1009-9095-6 Nut – M12

5420-40 78-8100-0926-2 Bracket – R/H, 100a, 200a, 700a, 800a

5420-41 78-8100-0927-0 Bracket – L/H, 100a, 200a, 700a, 800a

5420-42 78-8100-0924-7 Bracket – R/H

5420-43 78-8100-0925-4 Bracket – L/H

5420-44 26-1003-5842-8 Screw – Hex Hd, M8 x 20

Figure 5421

300cf Case Former

Figure 5421

Ref. No. 3M Part No. Description

5421-1 78-8114-4983-0 Support – Valve, R/H

5421-2 78-8114-4984-8 Support – Valve, L/H

5421-3 78-8032-0375-7 Screw – Hex Hd – M6 x 16

5421-4 26-1000-0010-3 Washer – Flat, M6

5421-5 78-8094-6081-5 Hinge

5421-6 78-8100-0930-4 Support – Cam

5421-7 78-8114-4985-5 Cam – Flap, R/H

5421-8 78-8114-4986-3 Cam – Flap, L/H

5421-9 78-8100-0933-8 Actuator – Valve, R/H

5421-10 78-8094-6083-1 Lever – Actuator

5421-11 26-1005-5316-8 Screw – Flat Hd Hex Dr, M5 x 16

5421-12 78-8052-6600-0 Spacer

5421-13 78-8070-1269-1 Bumper

5421-14 78-8010-7417-6 Nut – Hex, M5

5421-15 78-8094-6084-9 Limit Switch PXC-M521

5421-16 26-1003-7946-5 Screw – Soc Hd, M4 x 25

5421-17 78-8005-5740-3 Washer – Plain, M4

5421-18 78-8010-7416-8 Nut – Hex, M4

5421-19 78-8055-0786-6 Support – Shaft Right

5421-20 78-8055-0782-5 Support – Shaft Left

5421-21 26-1003-5833-7 Screw – Hex Hd, 6 x 30

5421-25 78-8114-4674-5 Support – Long

5421-26 78-8114-4675-2 Support – Short

5421-27 26-1003-7951-5 Screw – Soc Hd Hex Soc, M5 x 20

5421-30 78-8055-0783-3 Washer – D18/30 x 7

5421-31 78-8055-0781-7 Ring Nut

5421-32 78-8055-0787-4 Washer – D14 /30 x 5

5421-33 78-8055-0790-8 Shaft – Cylinder Support

5421-34 78-8052-6566-3 Washer – Friction

5421-35 26-1003-6918-5 Nut – Hex Flange, M10

5421-36 78-8094-6087-2 Cylinder – C65 B332-125C-Y2

5421-37 78-8057-5748-7 Mount – Cylinder Rod End

5421-38 78-8016-5855-6 E-Ring – 10 mm

5421-39 78-8055-0785-8 Lever – Cylinder, Right

5421-40 78-8055-0784-1 Lever – Cylinder, Left

5421-41 78-8017-9301-5 Screw – Hex Hd, M8 x 25

5421-42 26-1003-7976-2 Screw – Hex Hd, M10 x 35

5421-43 26-1005-6893-5 Elbow – 90°

5421-44 26-1005-6895-0 Elbow – 90°

5421-45 78-8094-6078-1 Sensor – 78180410

5421-46 78-8114-4987-1 Spring – Cam

5421-47 78-8119-8701-1 Flap Folder Assembly – R/H

5421-48 78-8119-8702-9 Flap Folder Assembly – L/H

5421-49 78-8119-8703-7 Plate – Flap Folder, R/H

5421-50 78-8119-8704-5 Plate – Flap Folder, L/H

5421-51 26-1001-9843-6 Screw – Flat Soc Hd, M6 x 16

5421-52 78-8100-0936-1 Arm

Figure 5422

300cf Case Former

Figure 5422

Ref. No. 3M Part No. Description

5422-1 78-8100-0938-7 Lever – Front

5422-2 78-8055-0808-8 Sprocket

5422-3 78-8010-7165-1 Screw – Flat Hd Soc, M5 x 25

5422-4 78-8005-5741-1 Washer – Flat, M5

5422-5 78-8055-0807-0 Shoulder Bolt

5422-6 78-8055-0806-2 Spacer – D16/30 x 35

5422-7 78-8052-6566-3 Washer – Friction

5422-8 26-1003-6918-5 Nut – Hex Flange, M10

5422-9 78-8100-0939-5 Chain – 3/8 Inch Pitch, 28 Pitch

5422-10 78-8054-8777-0 Chain – 3/8 Inch, 41 Pitch Long

5422-11 78-8054-8786-1 Chain Connector

5422-12 78-8054-8788-7 Chain Connector

5422-13 78-8054-8785-3 Rod – Threaded Right/Left

5422-14 78-8010-7418-4 Nut – Hex, M6

5422-15 78-8054-8784-6 Block – Chain

5422-16 78-8054-8787-9 Chain Link

5422-17 78-8056-3945-3 E-Ring – M4

5422-18 78-8060-7520-2 Screw – M3 x 20

5422-19 78-8059-5517-2 Nut – Self-Locking, M3

5422-20 78-8060-7519-4 Screw – M3 x 25

5422-21 78-8054-8783-8 Washer – Special

5422-22 78-8055-0800-5 Plate – 5 x 15 x 70

5422-23 78-8059-5526-3 Screw – Soc Hd Hex Soc Dr – M6 x 15

5422-24 78-8054-8779-6 End Cap

5422-25 78-8100-0940-3 Hexagon – Threaded

5422-26 78-8060-8452-7 Washer – M10

5422-27 78-8100-0941-1 Washer – Nylon

5422-28 78-8070-1549-6 Knob – VTR-B-M10

Figure 5423

300cf Case Former

Figure 5423

Ref. No. 3M Part No. Description

5423-1 78-8100-0942-9 Lever – Rear, R/H

5423-2 78-8100-0943-7 Lever – Rear, L/H

5423-3 78-8094-6057-5 Shaft – Lever

5423-4 78-8052-6566-3 Washer – Friction

5423-5 26-1003-6918-5 Nut – Plastic Insert Hex, M10

5423-6 78-8054-8577-4 Washer – Special

5423-7 26-1001-9843-6 Screw – Flat Soc Hd, M6 x 16

5423-8 78-8055-0798-1 Guide – Centering

5423-9 78-8055-0800-5 Plate – 5 x 15 x 70

5423-10 78-8059-5526-3 Screw – Soc Hd Hex Soc Dr, M6 x 15

5423-11 78-8054-8779-6 End – Cap

5423-12 78-8114-4678-6 Screw – Hex Hd, M10 x 50

5423-13 78-8114-4679-4 Spacer

5423-14 78-8114-4680-2 Guide Adjustment

5423-15 26-1003-7957-2 Screw – Soc Hd Hex Hd, M6 x 16

5423-16 26-1000-0010-3 Washer – Flat, M6

5423-17 78-8100-0941-1 Washer – Nylon

5423-18 78-8060-8452-7 Washer – M10

5423-19 78-8070-1549-6 Knob – VTR-B-M10

5423-20 78-8100-0969-2 Extension Assembly – Side Guide

5423-21 78-8100-0971-8 Extension – Inner

5423-22 78-8100-0970-0 Extension – Outer

5423-23 78-8100-0972-6 Plate

5423-24 78-8023-2334-1 Screw – Soc Hd Hex Soc, M6 x 25

Figure 5424

300cf Case Former

Figure 5424

Ref. No. 3M Part No. Description

5424-1 78-8094-6089-8 Bracket

5424-2 78-8032-0375-7 Screw – Hex Hd, M6 x 16

5424-3 78-8042-2919-9 Washer – Triple, M6

5424-4 78-8114-4681-0 Box Holder

5424-5 26-1000-0010-3 Washer – Flat, M6

5424-6 78-8010-7418-4 Nut – Hex, M6

5424-7 78-8114-4988-9 Support – Cylinder

5424-8 78-8010-7210-5 Screw – Soc Hd Hex Soc, M6 x 20

5424-9 78-8100-0947-8 Plate

5424-10 78-8032-0382-3 Screw – Soc Hex Hd, M5 x 16

5424-11 78-8005-5741-1 Washer – Flat, M5

5424-12 78-8100-0948-6 Cylinder – C65B40-500C

5424-13 78-8055-0768-4 Sliding Block – Ejector Guide

5424-14 78-8114-4682-8 Sliding Block – L/H

5424-15 25-1003-7951-5 Screw – Soc Hd Hex Soc, M5 x 20

5424-16 26-1005-6859-6 Nut – Self-Locking, M5

5424-17 78-8060-8454-3 Union – 1/2 Inch

5424-18 78-8060-8455-0 Sheath – /18 (1 MT)

5424-19 78-8114-4683-6 Flap Folder – Cylinder

5424-20 78-8119-8682-3 Bracket – Cylinder

5424-21 78-8060-7933-7 Guide

5424-22 78-8060-8179-6 Screw – Flat Hd Hex, M6 x 20

5424-23 26-1003-6916-9 Nut – Locking Plastic Insert, M6

5424-25 78-8100-0783-7 Washer – Special, /12

5424-26 78-8091-0775-4 Nut – M12 x 1.25

5424-27 78-8114-4684-4 Sliding – Flap Folder

5424-28 78-8100-0952-8 Screw – Soc Hd Hex Hd, M5 x 14

5424-29 78-8100-0953-6 Latch

5424-30 78-8094-6096-3 Sleeve – Latch

5424-31 78-8055-0775-9 Jack – Ejector

5424-32 78-8094-6097-1 Spring

5424-33 78-8055-0772-6 Spacer – D8/15 x 8

5424-34 78-8100-0954-4 Knob

5424-35 78-8017-9096-1 Nut – Special, M18 x 1

5424-36 78-8091-0510-5 Regulator – Speed

5424-37 78-8094-6078-1 Sensor – 78180410

5424-38 78-8060-7690-3 Cap – B-1/8 Inch

5424-44 26-1002-5820-6 Screw – Hex Hd, M5 x 16

5424-45 78-8114-4686-9 Bumper

5424-46 78-8114-4687-7 Slide

5424-47 78-8094-6079-9 Union – Y, Male

5424-48 78-8057-5735-4 Fitting – Reducer

5424-49 78-8055-0640-5 Spacer – Collar

5424-50 78-8119-6870-6 Cover – Support, W/English

5424-51 78-8114-4990-5 Push Button Assembly – Parker

5424-52 78-8114-4991-3 Union

5424-53 78-8114-4992-1 Bumper

5424-54 78-8119-8683-1 Bushing – Cylinder

5424-55 78-8094-6451-0 Valve – Selector, Parker

5424-56 78-8119-8684-9 Valve – W/Support, PXB-B1011

5424-57 78-8119-8685-6 Button – Pulse, ZB2-BA6

5424-58 78-8119-8686-4 Valve – Single, PXB-B1921

5424-59 78-8119-8687-2 E-Stop

Figure 5425

300cf Case Former

Figure 5425

Ref. No. 3M Part No. Description

5425-1 78-8100-0956-9 Filter Regulator/Assembly

5425-2 26-1014-4558-8 Filter – Regulator, W/Metal Bowl

5425-3 78-8100-0957-7 Valve – EVHS 2500-F02-X116

5425-4 78-8100-0958-5 Block

5425-5 78-8060-7900-6 Union – RA 022, 1/4 Inch - 1/4 Inch

5425-6 26-1005-6897-6 Hose Connector – RA 030 9 1/4 Inch

5425-7 26-1005-6890-1 Muffler

5425-8 78-8055-0756-9 Union

5425-9 78-8076-4891-6 Union – Straight KQHH-O1S

5425-10 78-8032-0382-3 Screw – Soc Hd, Hex Soc, M5 x 16

5425-11 78-8028-8214-8 Washer

5425-12 78-8091-0430-6 Clamp – /14-24

5425-13 78-8054-8838-0 Gauge – Air

5425-14 78-8076-4672-0 Union – Straight, Female

5425-15 78-8094-6071-6 Valve – PXB-B2011BD2

5425-16 78-8100-0959-3 Valve Assembly

5425-17 78-8119-8705-2 Manifold

5425-18 78-8094-6074-0 Valve – EVZA 5220

5425-19 78-8076-4886-6 Muffler – 1/4 Inch

5425-20 78-8094-6075-7 Union – Straight

5425-21 78-8119-8706-0 Union

5425-22 26-1003-7947-3 Screw – Soc Hd Hex Soc, M4 x 35

5425-23 78-8005-5740-3 Washer – Plain, 4 mm

5425-24 78-8057-5732-1 Fitting – Elbow

5425-25 26-1005-6893-5 Elbow – 90 Degree

5425-26 78-8094-6077-3 Regulator – Flow, 77080610

5425-27 78-8094-6076-5 Union – Y

5425-28 78-8114-4688-5 Valve Assembly – EVZA 5220

5425-29 26-1005-5909-0 ELbow

5425-30 26-1005-6910-7 Union – Straight

5425-31 78-8076-4537-5 Screw – Soc Hd, Hex Hd, M3 x 25

5425-32 78-8076-4538-3 Washer – Flat, M3

5425-33 78-8114-4690-1 Nut – M3

5425-34 78-8076-4675-3 Regulator – 0.5-7 BAR

5425-36 78-8114-4673-7 Bracket

5425-37 26-1003-7957-2 Screw – Soc Hd Hex Hd, M6 x 16

5425-38 26-1000-0010-3 Washer – Flat, M6

5425-39 78-8094-6451-0 Valve – Selector, PLK-A11

5425-40 78-8076-4664-7 Union – Female

5425-41 78-8094-6079-9 Union – Y, Female

5425-42 78-8057-6170-3 Tee – Tubing, 6 mm

5425-43 78-8057-5735-4 Fitting – Reducer

5425-44 78-8060-8033-5 Tubing – 5M Skein, D4/3

5425-45 78-8060-8034-3 Tubing – 5M Skein, D6/4

5425-46 78-8076-4911-2 Tubing – DX6, 5 MT

120af-if Infeed Conveyor

Safety and Information Labels

A label kit, part number 78-8113-6932-7 is available as a stock item. It contains all the safety and information

labels used on the coder conveyor, or labels can be ordered separately from the following list.

Ref. No. 3M Part No. Description Qty.

1 78-8062-4266-1 Label – Product 2

2 78-8070-1329-3 Label – Warning, Hazardous Voltage 1

3 78-8068-3859-1 Label – Service and Spares 1

4 78-8060-8481-6 Label – Leg 4

120af-if Safety and Information Labels

3M 300cf 300cf, Type 29800 User Manual To The 10470027 Bf23 4667 Be4d 3f4872ec4f1b

Navigation menu

Versions of this User Manual:

Views

Navigation