3e Technologies WLAN-MP1 802.11 a/b/g Modular transmitter User Manual Manual revised

3e Technologies International, Inc. 802.11 a/b/g Modular transmitter Manual revised

Manual revised

Download: 3e Technologies WLAN-MP1 802.11 a/b/g Modular transmitter User Manual Manual revised
Mirror Download [FCC.gov]3e Technologies WLAN-MP1 802.11 a/b/g Modular transmitter User Manual Manual revised
Document ID528982
Application IDwbRbAf6ILgaMz83R9RwsrA==
Document DescriptionManual revised
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize82.48kB (1031045 bits)
Date Submitted2005-04-05 00:00:00
Date Available2005-04-04 00:00:00
Creation Date2005-04-05 13:48:24
Producing SoftwareCorel PDF Engine Version 11.2.0.239
Document Lastmod2005-04-05 13:48:24
Document TitleManual revised
Document CreatorPrint Server 120
Document Author: Les Payne

Swarm mulblnd 1m
IEEE 002.11!!!“ l‘hI-PCI MW
NW wausm-z Umm
Super AIG Dual Band
IEEE 802.11 Wireless MInI-PCI Bus Adapter
NL-5354 MP PLUS Ariesz
User's Manual
Rev 1.1
Phfldfl
summon-land 1511"
EE m.“ mumxrmw
NLmMPHUSM-ZU-rllhm-
wezmchrmpuwm Mnflhnfldflopfld‘fistN
miwhahwwwn-fluwdfivuuwkmincmmmu
whwhnmionhth-ehdon’almm‘mfl
hTMmmwMuthmhdm-mmwhm
MubmmuflWGhmdkT-cbbgsmfidnpwfiuificfimdm
mane: .
hf ' Wmihfiimwmm,mumdmw
“fixwmhmmghwmmweflhd
malamfiliy. sown-airy Mh'afilmm leTegh-lop'awmmh
Wumhbmfladhhmuumidhfiubmtwh
Kmiwmumflhnfiwhfismzuwfllm
muwmtmaamdflonmmaupwbmnwhufl‘w
alum-Mailsimnuhm“mam-Mlmcfmlh-amh
TMIMMMaWJflhnu-Mbyu
msnm mmm
Uyw-alhhdfiufiumamahfisbawflu-dhynfiabufidhfim
Mbywafiofibhflwfit
MMdfl-flmMnMflh-flndwmflynfivmm
WehflimduWCmSoM"uHmfi-DFARS Eur-muommsam
willinfrahhdinfflllolwflaMkpfifivfixdyaflrasnmywfldhh
Twma'unmmmmnmmrmmumm-flw
MuhamflhmflfllLfl-WU (Nor IMJGPAX 51127-l4m. run-him hgfliflk.
YummnmnuuwmuwuNunflduwlwmdmmcbauu-nn
mfidhmhhflnmhmmfiisUmGfih
hTWmMthTMMWmmm-dnhfls
wm=amwwmm Awehmflwnhamw
Whitmdhmnm'fldifivmm
mum‘s
whrmrmwmmnuwmus. nd‘athmlpm
mmumw—hm.
Table of Corn-ms
Chapter 1 Introduction .......................................................................................... 3
Chapter 2 Hardware Spec..
21 Hardware specification ..
Hardnere Configuration
Hardware Installation...
22 NL-5354 MP PLUS Ariesz Technical Description
23 Installation Information...
Chapter 3 Driver Inlorrnafion: ..
Chapter 4 FCC and Regulatory Control Information .
IMPORTANT NOTE:..
Antenna Infon'nafiort .
Appendix A Regulatory
AQOQGNQO’JOIOQ
Midi?
super MG nut and
EE 002.11 “ital-s “MPG AM"
1-5354 NP PLUSWZ use” Wild
Chapter 1 Introduction
The Dual-Band tMreless AIG Mini PCI bus adapter operates seamlessly and
sirmitanewsly in both the 2.4GHz and SGHz lrequency spectrums supporting
the 802.11b (Z4GHz.11Mbps)and the newer, faster 802‘11a(SGHz,
54MbpsltoaMbps turbo mode) and 802,119 (2.4GHz, 54Mhps) wireless
standards. It’s the best way to add wireless capability to your exifling wired
mtwork, or to add bandwidth to your wireless instdlarion.
To protectywr wireless connectivity, the Dual-Bard Wireless MG Mini PCI bus
adapter can encrypt all wireless trarsmissions throum 64112811524)“ WEP data
encryption. Dynam'c Frequency Selection (DFS) pins you network on the
cleanest channel in your location. With the Dual-Bmd Wirelew Mini PCI bus
adapter, you will experience the best wireless connectivity nowadays.
Chapter 2 Hardware Spec
2.1 Hardware specificatlon
S” N6 our and wlllhl lid-PCI Motor-ll.-
535! IIP PLUS m
' Prom Denali-m:
~SGHfl2AGHZDIHhIMMhIPQAflm
-S|perA/G|plotoalotbpo
Dunn:- sun-19, 12, 13' 24, so, 43, 54, 12,985 we
(Amman: we) (Suoer A) M
302119: a. 9.12.1a.2l.se.4s.50,12.se a ton
(Saw 0) M
601111): I,2.55, “W9.-
NMK sum WECA (Wt-Fl 5 tM-FIS WW). lEEEflJZJ I.
lElHOZHI. IEEEOOZHU, IEEENZHD. M
P351 s-.-i l2
Super AIG Dual Band
IEEE 002.11 Wildest Milli-PC! Adam
N L-5354 MP PLUS An'es: Use“ Manual
IEEE 302.11e,v,h,anai standards, IEEEBDZ 1 x
Complfiance FCC Pad 15 Class B / UL= ETSI 300/3281CE
Drivers Wndows 985W EI200NXP
Operational vonage 3.3 V
Seculily IP IEEE802.1X 51190011 for LEA PIPEAP
WPA - WLFi Pmlecfied Access MES. $4125.15}
WEP with shared-key Authentication)
AES (Adece Encryption Secu'fly) Suppm
RF Information
Frequency Band 302.115
- 5.25 - 5.3mm,
. 5,725 - 5325611:
502.1 1 big
. 2,412 - 2,45st“)
. 2.412 - 2,484GHthapan)
. 2,412 - lam-mama» ETSI)
. 2.457 . 2,462(5Hz(Spam)
- 2,457 - 244726H11Fm0e)
Media Accesi Pmtocoi CS MAICA with ACK
Modulation Technology 302.113I9: OFDM (Gt-OAM‘ 16-QAM. OPSK.
spsx)
802.1117 : Dsss (DBPSK DQPsK, CCK)
Receive Sensitivity 802.111
49am (3 6mm. »7 SdBm @ 43mm,
-7DdBm @ 54Mhpa
802119“
433115!“ @ amps. -7 3dBm @ 4mm»,
-7DdBm a; 54mm
302.11b1
Pige4d|2
Super AIG Dual Band
IEEE 802.11 Wireless Milli-PCI Adapter
NL-5354 MP PLUS M952 Users Manual
-93d5m @ 1Mbps, £541an @ HMhps
TransmitommlPower Hymnal) 802.1“):
l7dEm 4.2 @ 5.2mm,»
14115!“ +12 ca 54mm
lsdBm +/.2 @ asMhps
lidBm +l-2 @ 45mm
802,115;
19dBm +l-2dBm a: s . 24mm
was.“ +I-2dBm @ as Mbpa
leBm +I-2dBm Q 36 Mbps 1665!" +I-Zd6m @ 54
Mbvs
502.11»:
leEm ol—dem lot all rules
Physical
Interface Mmi PCI Type III A
Connector 2 x UH. nonfiction
Dinensms (HxWxL) 4.5mm x 595mm 1 50.9mm (0.2in x 2.3in x 2in)
Weighl 15 90153 02.)
Environmental
Temwamre Range cc to SSC (32Fto l3|F)- Operating
40cm 70C(-4OF lo 158F) » $07.99
Humdity (non—condensing) 556 - 95‘3G Typtcal
Hardware Configuration
1. RJ-4S Ethernet connector
Prawdes NV 100 M'bps connectivity to 3 Wired Ethernet LAN.
2. Reset Button
By“ pressing this button for over 3 seconds. the AP will be reset wtth factory default
configumtim
3. Power Supply connector
It IS for counccuug to the power adapter.
Papefid'fl
super Ai‘G Dual Bind
IEEE 802.1 1 V-fiveless Mini-PCl Adapter
NL-5354 MP PLUS Aries! Users Manual
Hardware Ins talla tic n
1. Configure your notebook or PC with Wireless LAN card.
2. For \Vired LAN. connect your PCs’ Ethernet port to any AP's LAN port by an
Ethernet cable.
3. For W'LAN. locate the AP to a proper position
4. Plug the power cord into a power outlet.
2.2 NL-5354 MP PLUS Ariesz Technical Description
The NL-5354 MP PLUS AriesZ card is made by Senao International Co, Ltd
(wwwsenaocom) with datasheet link:
h ww smaocom‘cu ishl oduct’ oduct wuelessOl outdoor 1.35 .7
&mlid=02&m2id=03gproid=000145
It functions as an 8021 13/9 Dual Band Wireless Mini-POI Adapter. It uses the
It includes 2 chips: Atheros AR 5212 Mac controller, and Athe ros AR5112 Dual
band Radioon-a-Chip (RoC).
The NL-5354 MP PLUS Aries2 card has functions which are described below
. Support for IEEE 802.11a, 802.11b, 802.11g
. Universal wireless connectivity for seamless roaming between any
802.11-based network
- Uses digital CMOS technology exclusively, minimizing power consumption
and cost while maximizing reliability
Highly integrated 2-chip set
2.4/5 GHz dual band Radio-on-a-Chip (R00)
Multipretocol MAC / baseband processor that supports the R00
Wireless Multimedia Enhancements Quality of Service support (ODS)
Super AG 7“ mode delivers up to 108 Mbps raw data rate with typical end
user throughput exceeding 60 Mbps
- Hardware encryption for the Wi—Fi Protected Access (WPA) and IEEE
802.11 i security specifications, provides Advanced Encryption Standard
(AES), Temporal Key Integrity Protocol (TKIP) and Wired Equivalent
Privacy (WEP) without performance degradation
. Dynamic Frequency Selection/Transmit Power Control (DPS/11°C) for
international operation
- Support for drafl lEEE 302.115:y hI and i standards
. Enhanced third generation performance, transmission range and reliability
The NL-5354 MP PLUS AriesZ card uses the chipset functions as follows:
Papeeoriz
Super AIG Dual Band ,_,_
IEEE 802.11 Wireless Milli-PCI Adapter
NL-5354 MP PLUS Aries: Users Manual
AR5112 Dual band Radio—on—a-Chip (R00)
All CMOS dual band radio chip
Dynamic IF Dual Conversion architecture provides super—heterodyne
performance at Zero IF prices
Support for IEEE 802,11a, 302.11b, 802.119
Operates from 2.3-2.5 GHz and 525-5850 GHz
Integrated thirdgeneration power amplifier (PA) and low—noise amplifier
(LNA)
External PA and/or LNA can be used for special applications
Eliminates all IF filters and most RF filters; no external voltage—controlled
oscillators (VCOs) or surface acoustic wave (SAW) filters needed
Increased sensitivity and multipath tolerance
Enhanced transmit and receive chains
AR5212 Multiprotocol MAC/baseband processor
.-...
Supports both 2.4 GHz and 5 GHz RoCs
Super AIGWI mode rncludes dynamic 108 Mbps capability, real-time
hardware data compression, dynamic tran smit optimization and
standards—compliant bursting
No external FLASH or RAM memory needed
PCI 2.3 and PC Card 7.1 host interfaces with DMA support
Integrated analogtodigital and digital-toanalog converters
Serial EEPROM, LEDs, GPlOs peripheral interfaces
Low power operational and sleep modes.
2.3 Installation Information
The card has 2 U.FL RF connectors for antenna diversity,
The A2 is for both transmission and receiving, but the A1 is for receiving only
The A1 and A2 support 802,11a, b, g in auto-switch inside the chipset.
Paye7d12
super AlG our and 11mm
IEEE 002.11 wirel as Mini-POI Adapter
NL-5354 MP PLUS Aries2 Users Manual
Chapter 3 Driver Information:
The software driver can be downloaded from the link below:
htt :/Iwww.senao.comlen Iish/ roduc‘ll roduct load was ?htt =1& ord=000
fi
Chapter 4 FCC and Regulatory Control Information
To assure continued compliance (example - use only shielded interface cables
when connecting to computer or peripheral devices), any changes or
modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate this equipment
Radio Frequency Interference Requirements:
This device complies with Part 15 of FCC Rules and Canada RSS-210,
Operation is subject to the following conditions:
1. This devrce may not cause harmful interference,
Pm8d|2
Super MG Dual Band
IEEE 8102.1 1 W'Irel es; MiniPCl Adapter
NL—5354 MP PLUS M652 Users Manual
2. This device must accept any interference received, including
interference that
may cause undesired operation.
3, This transmitter must not be co-Iocated or operated in conjunction with any
other antenna or transmitter.
Interference Statement
This equipment has been tested and found to comply With the limits for a Class B
digital device, pursuant to Pan 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or televrsion reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
We declare that NL-5354 MP Plus Ariesz (Atheros 1 talg Mini PCI Bus Adapter)
is limited in CH1~CH1 1 by specified firmware controlled in the USA.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This devrce complies wrth FCC RF Exposure limits set forth for an uncontrolled
environment, under 47 CFR 2.1093 paragraph (d)(2).
To comply with FCC RF exposure compliance requirements, the antenna used
for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-Iocated or operating in conjunction
with any other antenna or transmitter.
This transmitter mu st not be colocated or operating in conjunction with any other
antenna or transmitter.
This module is restricted to the described / contained herein 3eTI applicationls)
The module is for OEM installation only and cannot be sold to end user directly.
Antenna In formation:
Only the antenna ripe: listed below can be used:
Antenna 1: Bdbi omnidirectional antennas for 802.11a
Papefioftz
Super AIG Dual Band
IEEE 802.11 Wireless Milli—PC! Adapt“
NL-5354 MP PLUS Aries: Users Manual
Antenna 2: Sdbi omni directional antennas for 802.1 1g/b
Antenna 3: 14db| directional antennas for 802A11glb
This module must be labeled with FCC ID.
If the FCC ID is not visible when the module is installed inside another device,
then the outside of device must also display a label referring to the enclosed
module. The exterior label can be “ Contains Transmitter Module FCC
lD:QVT-WLAN-MP1 " or similar wording.
Pagelbaflz
Super AJG Dual Band iix'fl'flfi
[EEE 502.11 Wireless Milli-Pct MEN“
NL-5354 MP FLUS M832 Users Mflfllltl
Appendix A Regulatory Compliance
Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply With the limits for a Class B
digital device, pursuant to Pan 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation. if this
equipment does cause harmful interference to radio or television reception, which
can be determined by tuming the eqmpment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
~ Reorient or relocate the receivrng antenna.
- In crease the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technicran for help.
This devrce complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this devrce must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equrpment.
IMPORTANT NOTE:
Fcc Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled envrronment. This equipment should be installed and operated with
minimum distance 20cm between the radiator 8. your body.
This device is intended only for OEM integrators under the following
conditions:
The antenna must be installed such that 20 cm is maintained between the
antenna and users As long as condition above is met, further transmitter
test will not be required. However, the OEM integrator is still responsrble for testing
their end-product for any additional compliance requirements requrred With this
module installed (forexample, digital device emissions, PC peripheral requirements,
etc).
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations of co—Iocatrion wnh another msrmtter). then the FCC
authonutron Ls no longer considered valid and the FCC ID can not be used on the final
Pagefloffll
NL5354 MP PLUS Aries2 Users Manual
product. In these circumstances. the OEM integrator will be responsible
for re-evaluating
the end product (ineludmg the transrmtter) and obtaining a separate FCC authorization
Super AIS Dual Band 1:37.35;
1555 002.11 mrelesa Mini-PEI Adapter
End Product Labeling
This transmitter module 15 authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users (for example:
Access Point, Router) The final end product must be labeled in a “sible area with the
following: "Contours TX FCC ID: QVT-WLAN-MP1
Manual Information That Must be Included
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the users manual or the end
product which integrate this module The users manual for OEM integrators end
users must include the following information in a prominent location “ IMPORTANT
NOTE: To comply with FCC RF exposure compliance requirements, the antenna
used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be ctr-located or operating in conjunction with
any other antenna or transmitter.
Page 120112

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 12
Create Date                     : 2005:04:05 13:48:24
Modify Date                     : 2005:04:05 13:48:24
Producer                        : Corel PDF Engine Version 11.2.0.239
Author                          : Les  Payne
Creator                         : Print Server 120
Title                           : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: QVT-WLAN-MP1

Navigation menu