4IPNET 140002 11ac Dual Band concurrent Wall-mount AP User Manual 4ipnet EAP760 Handbook EN

Download:
Mirror Download [FCC.gov]
Document ID	2316950
Application ID	tY/yuvvQcMMfS+jH1HykFw==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	81.8kB (1022460 bits)
Date Submitted	2014-07-07 00:00:00
Date Available	2014-07-07 00:00:00
Creation Date	2014-07-04 11:52:45
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2014-07-04 11:52:45
Document Title	Microsoft Word - 4ipnet_EAP760_Handbook_EN.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	felix.fung

Product Handbook
EAP760 V1.00
Enterprise Access Point
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Copyright Notice
This document is protected by USA copyright laws and other laws. Besides, the
document is the property of 4IPNET, INC. You may not copy, reproduce, distribute,
publish, display, perform, or modify any part of this publication in any form or by any
means without prior written permission from 4IPNET, INC. You may not alter or remove any
copyright or other notice from copies of the content. All other brand and product names
are claimed or registered marks of their respective companies or organizations.
All rights reserved.
To download up-to-date version, please visit www.4ipnet.com.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
FCC CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
※
FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the
potential for harmful interference to co-channel Mobile Satellite systems.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
CE CAUTION
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Model: EAP760
For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and
hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.
• Radio: EN 300.328:
• EMC: EN 301.489-1, EN 301.489-17,
• EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings:
EN 61000-3-2, EN 61000-3-3.
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-11
• Safety: EN 60950-1 + A11,
Caution:
 This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by
4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range
2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be
restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory
authority for compliance.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Preface
Package Contents
4ipnet EAP760 is a high-end, dual radio 802.11
b/g/n + ac MIMO Access Point (AP) with the best
performance for business and industrial applications
1. 4ipnet EAP760 x 1
2. Quick Installation Guide (QIG) x 1
3. Wall Mount Kit x 1
and is compliant with the latest industrial wireless
security standards that are required in the tightly
secured enterprise network environments.
EAP760 makes the wireless communication fast,
secure and easy. It supports business grade
security such as 802.1X, and Wi-Fi Protected
Access (WPA and WPA2). The EAP760 supports
multiple point-to-point wireless links to form wider
wireless network coverage.
EAP760 also features multiple ESSIDs with VLAN
tags and multiple Virtual APs; great for enterprise
applications, such as separating traffic from different
departments using different ESSIDs. The PoE
Uplink port is able to receive power from Power over
Ethernet (PoE) sourcing devices.
This Quick Installation Guide provides instructions
and reference materials to get you started with
4ipnet EAP760.
Copyright © 4IPNET, INC. All rights reserved.
It is recommended to keep the original
packing material for possible future shipment
when repair or maintenance is required. Any
returned product should be packed in its
original packaging to prevent damage during
delivery.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
System Overview
EAP760 Front View
1 External Antenna
External antennas via SMA connectors. 1a, 1b and 1c corresponds to
Ant1, Ant2 and Ant3 of the system.
2 LED Indicator
An LED indicator is available to show the AP’s operation status. Green
indicates power on, and orange indicates WES’ status.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
EAP760 Back View
1 12V
2.5 A
2 Uplink (PoE) Port
Attach power adaptor here
Offers uplink connection. This port can be used to connect to a controller,
gateway, or directly to the Internet. 802.3at PoE is also supported
3 LAN 1 Port
The ports for connections with LAN side devices
4 USB Port
USB interface reserved for future use
5a WES Button (A)
For IT administrators to easily setup WDS links with the RF card (A).
5b WES Button (B)
For IT administrators to easily setup WDS links with the RF card (B).
6 Restart / Reset
Press once to restart the system; to reset the system to factory default
settings, hold for more than 5 seconds.
7 Console Port
To access EAP760 via the console interface.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Hardware Installation
Please follow the steps mentioned below to install the hardware of EAP760:
1. Place the EAP760 at the best location.
The best location for EAP760 is usually at the center of your intended wireless network.
2. Connect the EAP760 to your network device.
Connect one end of the Ethernet cable to the Uplink port of EAP760 and the other end of the cable to a switch,
a router, or a hub. EAP760 is then connected to your existing wired LAN network.
There are two ways to supply power over to EAP760.
3. Connect the DC power adapter to the EAP760 power socket.
EAP760 Uplink port is capable of receiving DC currents. Connect an IEEE 802.3at-compliant PSE device (e.g.
a PoE-switch) to the Uplink port of EAP760 with the Ethernet cable.
Now, the Hardware Installation is complete.
• Using a different power adapter may damage this system.
• To verify the wired connection between EAP760 and you switch / router / hub, please also
check the LED status indicator of the respective network devices.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Getting Started
4ipnet EAP760 supports web-based configuration. When hardware installation is complete, EAP760 can be
configured through a PC by using a web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0
and above.
The default values of LAN IP address and subnet mask of EAP760 are:
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
Steps:
1. To access the Web Management Interface, connect the administrator PC to the Uplink port of EAP760 via
an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP760 in TCP/IP of your
PC, such as the following example:
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
2. Launch the web browser on your PC by entering the IP address of EAP760 (https://192.168.1.1) in the
address field, and then press Enter.
Example of entering EAP760's default IP Address via a web browser
3. The following Admin Login Page will appear. Enter “admin” for both the Username and Password fields,
and then click Login.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Administrator Login Page
4. After a successful login to EAP760, a System Overview page of the Web Management Interface will
appear, as depicted below.
The Web Management Interface - System Overview Page
5. To logout, simply click on the Logout button at the upper right hand corner of the interface to return to the
Administrator Login Page. Click OK to logout.
Copyright © 4IPNET, INC. All rights reserved.
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Common Settings
Step 1. Change Administrator’s Password
Change Password Page
 Click on the Utilities icon on the main menu, and select the Change Password tab.
 Enter the old password and then a new password with a length of up to 32 characters, and retype it in
the Re-enter New Password field.
 Click SAVE to save the changes.
Copyright © 4IPNET, INC. All rights reserved.
10
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Step 2. Configure General AP (Access Point) Settings
Wireless General Settings Page
 Click on the Wireless icon on the main menu, and then select the General tab.
 Determine the Band and Channel settings:
Select your preferred Band and Channel for you wireless connection. For example, select
802.11g+802.11n for the band and 6 for the channel. For a detailed guide to configuration, please
refer to the EAP760 User Manual.

 Note:
Admin should be aware of Dynamic Frequency Selection (DFS) mandated on some channels of the
5GHz band. When an EAP760 detects interference, this mechanism will limit the ability to broadcast
the SSID on one of the channels listed below:
1) Country Code: 840 (US)
DFS Channels: 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140
2) Country Code: 250 (EU)
DFS Channels: 52 56 60 64
Copyright © 4IPNET, INC. All rights reserved.
11
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Step 3. Configure VAP (Virtual Access Point) Profile Settings
VAP Configuration Page (VAP-1 shown)
 EAP760 supports up to 16 virtual APs (VAPs) per RF Card.
 Configure VAP profile settings：
(a) Select the VAP Configuration tab to configure the settings of the desired VAP.
(b) Enable a specific VAP from the drop-down menu of Profile Name and configure related settings
below.
 Check VAP status：
After finishing VAP configuration, the status of enabled Virtual APs shall be reflected on the VAP
Overview page.
Copyright © 4IPNET, INC. All rights reserved.
12
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Virtual AP Overview Page
Copyright © 4IPNET, INC. All rights reserved.
13
Product Handbook
EAP760 Enterprise Access Point ENGLISH
Step 4. Configure WDS (Wireless Distribution System) Settings (Optional)
To extend the wireless coverage, EAP760 supports up to 8 WDS links for connecting wirelessly to other
WDS-capable APs (peer APs). By default, all WDS profiles are disabled.
 Click on the Wireless button on the main menu.
 Select the Repeater Settings tab.
 Choose WDS as the Repeater Type.
 Choose the desired WDS profile:
(a) Enable WDS.
(b) Enter the MAC Address (peer AP) and then Click SAVE.
If you are using another EAP760 as the peer AP, simply repeat the above-mentioned steps to configure
another peer AP(s).

 Note:
On each and every configuration page, you may click SAVE to save the changes of your configured
settings, but you must reboot the system for the changes to take effect. After clicking SAVE, the
following message will appear: “Some modifications have been saved and will take effect after
Reboot.”
Congratulations!
Now, 4ipnet EAP760 is installed and configured successfully.
Copyright © 4IPNET, INC. All rights reserved.
14
Product Handbook
EAP760 Enterprise Access Point ENGLISH
After EAP760's network configuration is completed, please remember to change the IP Address of
your PC Connection Properties back to its original settings in order to ensure that your PC functions
properly in its real network environments.

 It is strongly recommended to make a backup copy of your configuration settings.

 For further configuration and backup information, please refer to the User’s Manual.
P/N: V10020140703
Copyright © 4IPNET, INC. All rights reserved.
15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 16
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2014:07:04 11:52:45
Modify Date                     : 2014:07:04 11:52:45
Title                           : Microsoft Word - 4ipnet_EAP760_Handbook_EN.doc
Creator                         : PScript5.dll Version 5.2.2
Author                          : felix.fung

EXIF Metadata provided by EXIF.tools