4iiii Innovations SP100 ATHLETIC PARAMETER LED DISPLAY User Manual

4iiii Innovations Inc. ATHLETIC PARAMETER LED DISPLAY Users Manual

Users Manual

Welcome to Sport-iiiis!ank you for purchasing Sport-iiiis. Sport-iiiis is a heads-up display – it gives you the data you need to stay in your target range (zone) in any of several measures (including heart rate, cadence, power, and pace/speed) while running or cycling, without you having to look down at a watch, cyclocomputer, etc. It can pair with, and receive this data from, any ANT+-enabled heart rate strap, foot pod, power, or speed/cadence sensor.When properly mounted to your glasses, the boom of the Sport-iiiis unit will be in your peripheral vision, so that its LEDs can tell you whether you are below, above, or in your zone by their color (green, yellow, orange, or red) and position.rough the downloadable Sport-iiiis soware interface for your Windows or Mac OS computer, you can set up the Sport-iiiis unit and congure the zones for your individual needs.What’s in the Box?Sport-iiiis Unit(2) Mounting BracketsTie Wraps USB Charge/Sync Cable
Getting to Know Your Sport-iiiis UnitSpeakergives audio prompts either when triggered by Tip-Tap or (optionally) when above or below zone for currently enabled sensorMicro-USB Portconnect to computer to congure, charge, and sync your Sport-iiiis unitPower Buttoncapacitive-touch button (merely has to be touched, cannot be depressed), powers Sport-iiiis on and o and controls other functionsBoomcontains seven LEDs (Light-Emitting Diodes) that can be programmed by color and position to indicate where your per-formance is relative to the target zone for your cur-rently-enabled sensorACTION SPORT-IIIIS POWERED ON SPORT-IIIIS POWERED OFFpress Power Button(unit beeps once)hold Power Button until unit beeps twicehold Power Button until unit beeps three timeshold Power Button until unit beeps four timesstart/stop session show remaining battery powerturns Sport-iiiis unit o turns Sport-iiiis unit onswitch bike/run mode--------------pair sensorsclear all paired sensors & pairFunctions of the Power ButtonTipTapYour Sport-iiiis unit contains an accelerometer, which allows it to respond to single and double “taps,” as seen below:While it is powered on, a single tap will cause your Sport-iiiis unit to ennuciate the measurement from the active sen-sor, and a double tap (two taps in rapid succession) will switch between currently paired sensors.
Download and Set Up the Sport-iiiis SowareBoth Windows and Mac OS versions of the Sport-iiiis Application are available for download at:http://www.4iiii.com/support.htmlWindows Soware Installation:1. Download the Sport-iiiis Application Installer from http://www.4iiii.com/support.html2. Double-click on “installSport-iiiis.exe” to activate the Installer.3. Click on “Close” in the Installer’s dialog box once installation is complete.4. Double-click on the “Sport-iiiis” shortcut on your desktop to open the Sport-iiiis Application. Mac OS Soware Installation:1. Download the Sport-iiiis Application from http://www.4iiii.com/support.html2. Drag Sport-iiiis Application to your “Applications” folder.3. In your “Applications” folder, nd the “Sport-iiiis” icon and double-click on it to open the Sport-iiiis application Create Your ProleEnter your name, email, height, weight, birth year, gender, unit of measurement (English or Metric), and desired run display (pace or speed) to set up the initial conguration. You may always update this later by clicking on the “Prole” tab and making any desired changes.Set Your Target ZonesIn addition to the optional ANT+ heart rate strap, your Sport-iiiis unit is compatible with any ANT+-enabled bike (power, speed & cadence) and run (foot pod) sensors.You can choose target zones for the data provided by each of these sensors by clicking on the “Zones” tab in the le column of the Sport-iiiis soware interface and then choosing the appropriate activity type (“Run” or “Bike”) in the upper right of the interface window. en, on the bottom of the interface window, choose the sensor for which you would like to adjust the zone setup (Heartrate, Pace, and Cadence for Run, or Heart-rate, Speed, Cadence, and Power for Bike).e diamond in each zone indicates the LED color for that zone, and it can be moved up and down to adjust the LED color for that zone.To adjust the boundaries for each zone, simply click on the boundary you would like to adjust and drag your mouse in the appropriate direction to increase or decrease it as desired.In this menu, you may also choose whether your Sport-iiiis unit will beep when you move between zones (by clicking on “Enable zone change beeps”) and whether your Sport-iiiis unit will give you voice prompts (by clicking on “Enable voice prompts”).As soon as you have made any changes to your zone settings in the Sport-iiiis Application, the Upload Status Button in the le column of the interface will turn yellow and say “Ready to upload.” Your Sport-iiiis unit will not be updated with the new settings until you click on the Upload Status Button to begin the upload to the unit. Once the upload is complete, the Upload Status Button will turn green and say “OK to disconnect.”
Save and Load Your Target Zone ProlesOnce you have customized a Zone Prole for a sensor, you may save that prole by clicking on the “Save” button to the right of the Prole Name. When you do this, a dialog box will open up prompting you to name this new Zone Prole. Once you have entered the name, click on the “Save” button. e dialog box will disappear and the Prole Name will change to that which you just saved.You may also load Zone Proles that you have previously created and saved by clicking on the “Load” button to the le of the Prole Name. When you do this, a dialog box will open that will allow you to choose from all of your saved Zone Proles for that sensor. Simply choose the prole that you would like to load and click on the “Load” button to load that Zone Prole. You will then have to upload that prole to your Sport-iiiis unit by clicking on the Upload Status Button. Set the Preferences for Your Sport-iiiis UnitTo set the preferences up for your Sport-iiiis unit, simply click on the “Setup” tab in the le column of the Sport-iiiis Application interface and choose the parameter (LEDs, Audio, Sensors, TipTap) that you would like to change on the upper right.LEDsUse the Conguration buttons to set the Sport-iiiis unit up for the eye that you will be using it on (“Le eye” or “Right eye”). Use the sliders to adjust the maximum brightness (“Max bright-ness”), the sensitivity of the unit to ambient light (“Ambient light adjust”), the time the LED will continue to blink when you remain in the same zone (“Time to autofade”), and the blink rate of the center zone (“Center-Zone blink rate”).AudioYou may enable the Sport-iiiis audio functions by clicking on the “Audio enabled” button.Use the slider to adjust the volume level of your Sport-iiiis unit.SensorsEnter your wheel circumference in millimeters so that, when us-ing a paired ANT+-enabled speed/cadence sensor, your Sport-iiiis unit can give you accurate speed data on your bikeTipTapUse the slider to adjust the sensitivity of your Sport-iiiis unit to TipTap input. As soon as you have made any changes to your Setup in the Sport-iiiis Application, the Upload Status Button in the le column of the interface will turn yellow and say “Ready to upload.” Your Sport-iiiis unit will not be updated with the new settings until you click on the Upload Status Button to begin the upload to the unit. Once the upload is complete, the Upload Status Button will turn green and say “OK to disconnect.”Firmware UpdatesWhen it is running, the Sport-iiiis Application will automatically check for amd download rmware updates for your Sport-iiiis unit (this feature requires your computer to be connected to the Internet). Whenever it has downloaded any updates, the Update Status Button in the le column of the interface will turn yellow and say “Ready to upload.” When this occurs, simply click on the Update Status Button to up-load the new rmware to your Sport-iiiis unit. Once the upload is complete, the Upload Status Button will turn green and say “OK to disconnect”
Charging Sport-iiiisTo charge your Sport-iiiis unit, uncover the micro-USB port on the bottom of the unit and plug in the in-cluded USB 2.0 Charge/Sync Cable. Plug the other end of the cable into one of your computer’s USB ports a USB power adapter.When your Sport-iiiis unit is connected to your computer and you are running the Sport-iiiis Soware Ap-plication, the battery icon on the bottom le of the interface will indicate the charge status and percentage of battery power currently available in your Sport-iiiis unit.Mounting Sport-iiiis on Your Glasses1. Insert tie wraps into mounting brackets loosely, exactly as shown below:2. Slide the Sport-iiiis unit into the mounting bracket.3. Align the Sport-iiiis unit on the glasses as you’d like it to be mounted. At this point, choose whether you’d like the boom on the inside or the outside of the lens (extra tie wraps are included so that you can change your mind later).Boom Inside LensBoom Outside Lens
5. Slide the Sport-iiiis unit o of the mounting bracket and cinch down the tie wraps as much as possible.4. Carefully tighten the tie wraps to x the mounting bracket in place.6. Cut as much of the excess tails from the tie wraps.7. Slide your Sport-iiiis unit back onto the mount, bend the boom into its nal position, and go out and enjoy your Sport-iiiis unit!Technical SupportTechnical Support is available from 4iiii by both phone and email from 9am-5pm Mountain time.Phone: 1.800.218.3095 or 1.403.800.3095Email: support@4iiii.comFCC Complianceis device complies with Part 15 of the FCC Rules,. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.IC Complianceis device complies with Industry Canada licence-exempt RSS standard(s). Op-eration is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interfer-ence that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux ap-pareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Navigation menu