8BITDO TECH SNF30V2 8Bitdo SF30 v2 Bluetooth GamePad User Manual
SHENZHEN 8BITDO TECH CO., LTD. 8Bitdo SF30 v2 Bluetooth GamePad Users Manual
Users Manual
80BI SN30 and SF30 Instruction Manual Basic Operation Please turn off the controller before swapping controller modes. Press and hold START for 3 seconds to turn off the controller. Bluetooth Connection ·Controllers will auto reconnect to your devices once they have been paired. Android (D-Input) 1. Press and hold START for 1 second to power on the controller, LED will blink once per cycle. 2. Press and hold SELECT for 3 seconds to enter pairing mode. Blue LED will rapidly blink. 3. Go to your Android device’s Bluetooth setting, pair with [8Bitdo xx GamePad]. 4. LED will be solid blue when connection is successful. · USB Connection: connect your 8Bitdo controller to your Android device via USB Cable after step 1. Windows (X-Input) 1. Press and hold START + X for 1 second to power on the controller, LED will blink twice per cycle. 2. Press and hold SELECT for 3 seconds to enter pairing mode. Blue LED will rapidly blink. 3. Go to your Windows device’s Bluetooth setting, pair with [8Bitdo xx GamePad(x)]. 4. LED will be solid blue when connection is successful. · USB Connection: connect your 8Bitdo controller to your Windows device via USB Cable after step 1. macOS 1. Press and hold START + A for 1 second to power on the controller, LED will blink three times per cycle. 2. Press and hold SLECT for 3 seconds to enter pairing mode. Blue LED will rapidly blink. 3. Go to your macOS device’s Bluetooth setting, pair with [Wireless Controller]. 4. LED will be solid blue when connection is successful. ·USB Connection: connect your 8Bitdo controller to your macOS device via USB Cable after step 1. Switch (by default) 1.Press and hold START + Y for 1 second to power on the controller, LED will blink four times per cycle. 2. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order. 3. Press and hold SELECT for 3 seconds to enter pairing mode. Blue LED will rapidly blink. 4. LEDs will be solid blue when connection is successful. ·When connected to your Switch, DOWN + SLECT = Switch HOME button. Battery Status LED Indicator Low battery mode LEDs blink in red Battery charging Battery fully charged LEDs blink in green LEDs stop blinking in green ·Built-in 480 mAh Li-on with18 Hours of play time. ·Rechargeable via USB cable with 1 – 2 hour charging time. ·Press START for 8 seconds to force turn off your controller Power Saving ·Sleep mode - 1 minute with no Bluetooth connection. ·Sleep mode - 15 minutes with Bluetooth connection but no use. ·Press START to wake up your controller. Support Please visit support.8bitdo.com for further information and additional support. FCC Statement 15.19 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 15.21 Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. 15.105(b) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : admin Description : Title : Comments : Company : Source Modified : D:20180111094713+01'47' Create Date : 2018:01:11 09:47:13+01:30 Creator Tool : WPS Office Modify Date : 2018:02:06 18:46:51+08:00 Metadata Date : 2018:02:06 18:46:51+08:00 Keywords : Producer : Document ID : uuid:3d2b70df-482c-477f-8912-e25e3b956e23 Instance ID : uuid:a302af1f-0e86-4ee1-96e1-1478cdf68b03 Page Count : 3 Author : admin Subject : Trapped : falseEXIF Metadata provided by EXIF.tools