A Four Tech Co RG20KM24G 2.4G RF Dongle User Manual 2 4G RF Dongle Manual

Download:
Mirror Download [FCC.gov]
Document ID	886378
Application ID	Kb9Opo0gbjGYUiU+l/rqQQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.5kB (356309 bits)
Date Submitted	2008-01-07 00:00:00
Date Available	2008-01-07 00:00:00
Creation Date	2007-12-20 16:42:34
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2007-12-20 16:42:34
Document Title	Microsoft Word - 2.4G RF Dongle Manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

G6 Saver
User’s Guide
Keyboard & Mouse Dongle
Model:RG-20KM
www.a4tech.com
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient of relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
-1-
Introduction:
2.4GHz wireless technology with 16 channels and 1,048,576 ID
Errorless 2-Way Communication Technology
Codes
The 2.4GHz RF wireless technology is fine-tuned with 16 selected
Errorless 2-way communication technology features error
channels and exclusive 1,048,576 ID-codes; it offers precise and
correction capability that speeds up data transmission and
smooth wireless operation in active wireless environments. It allows
increases wireless precision. It saves valuable battery power
many wireless devices to operate simultaneously in one area without
and cost.
interfering in the range up to 8-10 meters.
Anti-interference with Auto Channel Hopping Technology
Ultra Low Battery Power Consumption - Only 6mA!
"Auto Channel Hopping" technology automatically detects and
2.4G is designed with “4 Level Auto Power Saving” modes with
secures available channels in the busy public 2.4GHz universal band.
ultra low battery power consumption, it only requires 6mA of
It ensures better quality of wireless communication.
electric current to operate.
Ultra Low Battery Power Consumption - Only 6mA!
Say Goodbye To Double Click
2.4G is designed with “4-Level Auto Power Saving” modes. With ultra
Just one click on “2X Button” directly opens files and programs,
low battery power consumption, it only requires 6mA of electric current
saves time and improves efficiency.
to operate.
-2-
Specifications
2Mbps
Frequency
2.402GHz～2.480GHz
1,048,576 sets
Channels
16 channels
RF Data Transmit Rate
ID Codes
Wireless Range
Any electrical device, such as the computer monitor, Zip drives, speakers, etc., can cause interference with the wireless mouse/keyboard. Most likely, this will effect tracking of pointing devices or the range
of the device. To make sure that your mouse/keyboard transmits and receives properly, refer to the following instructions:
1. For optimal performance, place the receiver at least 8 inches (20 centimeters) away from
other electrical devices, such as the computer monitor, Zip drives, speakers…etc.
Keep 8 inches
2. The effective distance of wireless keyboard or mouse should be no farther than 26-33 feet (8
< 26-33 feet
-10 meters). This will ensure optimal communication between the mouse/keyboard and the
USB receiver.
NOTE: You should always get at least a 4 meters range. If you find that your cordless device gets less than 4 meters range, please
replace the batteries with a fresh set, perform the synchronization procedure for the mouse/keyboard and test the range again. If the
range is still below 4 feet, please test your device on another system, preferably in a different environment. If you find it gets the same
range on another system, please contact A4 TECH support to obtain information about a warranty replacement. However, if the range
improves on another system, then it may be an environmental variable. Use the suggestions above to resolve the environmental
interference issue.
Operating Warnings: For optimal performance and RF (Radio Frequency) reception:
1. Avoid using the wireless mouse/keyboard on a metal desk or a desk with a metal frame can cause problems with
pointing device behavior and range.
2. The mouse/keyboard will enter a suspend mode at the same time your computer dose, click a button on the
mouse/keyboard presenter to activate it.
3. Never use the mouse on the glass or mirrored surface.
-3-
Hardware Installation
Step 1: Inserting the Batteries
A. Press the tab on the battery cover
B. Insert the supplied batteries, making sure that the
locates on the mouse/keyboard
positive (+) and negative (-) ends of the battery
bottom as shown here and
match the polarity indicators inside the battery
remove the cover.
housing.
C. Slide the batter cover back into its
position until it “clicks” firmly into place.
Keyboard
-4-
Step 2: Connect the Receiver
A. For Notebook computer:
A. For PC computer:
Insert the USB receiver into the USB port of your Notebook
Insert the USB receiver into the USB port of desktop computer or
computer.
via a USB HUB.
B. The USB receiver will automatically be recognized by your computer.
C. Press the “connect” button on the USB receiver as shown,
the Green Power LED will light up, and starts “Blinking”.
D. Immediately Press the “connect” button on the bottom of the
mouse, If you can’t find or see your cursor on the screen, follow
the steps below: (If the keyboard connected, you can try press
any keys to try key working.)
1. Unplug and re-plug the receiver
2.Test the device on another USB port or computer.
3. Some surfaces may “trick” the optical sensor, such as reflective
surfaces like glass or mirrors. The Optical sensor should perform
well on all other surfaces.
-5-
Power Management
1. To power on the mouse/keyboard, press the connect button on the bottom of the
mouse once.
2. To turn off the mouse, press and hold the connect button on the bottom of the mouse
until its optical light (RED) turns off.
Note: Removing the batteries will require you to synchronize it with the receiver again
the next time you turn it back on.
Power on/off
Keyboard Connect Button
-6-
● System Requirements：
● Package Includes：
To use the mouse/keyboard presenter, your computer must meet the following hardware requirements
□ 2.4GHz RF Mouse
and run one of the operating system listed below.
□ USB RF Receiver
Hardware
Operating System
□ 2 AAA Alkaline Batteries
□ IBM or Compatible PC
□ Windows 2000, XP, MCE2005, XP (x64), 2003(x64), and VISTA x86
□ CD (User Manual on CD)
□ CD (User Manual on CD)
□ Hard Disk Driver
□ USB Port
** Please inform us if there is any discrepancy found in this manual. (Note: This manual may be revised without notice).
-7-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2007:12:20 16:42:34+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2007:12:20 16:42:34+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : Microsoft Word - 2.4G RF Dongle Manual.doc
Document ID                     : uuid:844f83bb-0522-42c9-be2d-b24059869887
Instance ID                     : uuid:c3104267-da03-4292-8a95-1faa1bfbe9d4
Page Count                      : 8
Author                          : Administrator

EXIF Metadata provided by EXIF.tools