A Four Tech Co RSWOP27 Radio Wireless Wheel MOUSE User Manual

Download:
Mirror Download [FCC.gov]
Document ID	298678
Application ID	1YkTfcZ496Tzwljlfn/NIg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.6kB (370032 bits)
Date Submitted	2003-01-27 00:00:00
Date Available	2003-01-27 00:00:00
Creation Date	2003-01-22 09:36:48
Producing Software	Acrobat 4.0 Scan Plug-in for Windows
Document Lastmod	2003-01-22 09:37:31
Document Title	User Manual
Document Creator	Acrobat 4.0 Scan Plug-in for Windows

Radio Wireless Wheel Mouse
User’s Guide
MODEL: RF SWOP—27
Trademark Recognition
windows, office 97/2000/xr and MS-lntclliMousc an: rcgismmd trademarks ofMicmwl‘K Corp,
III
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction, may cause harmful interference to radio communication, However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
0 Reorient of relocate the receiving antenna.
0 Increase the separation between the equipment and receiver
0 Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
0 Consult the dealer or an experienced radio/TV technician for help
The changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
|NTRODUCTION
Congrzurlulions on your purchase! Your new KF-Mouse is easy to install and arms you a host ofuseful
features The Radio recelver can be convenienlly placed to give you the freedom you need while working. The
vertical wheel allows you lo scmll, or zoom in and out in a documenl. You can program the mouse buttons to
launch the NeLlump or LuckyJump fora quick starl lo programs you run fiequemly. And, your RP-Mouse has n
unique ID code, so other RF (Radio Frequency) pointing devices won‘l afl‘ecl your system.
Connecting the RF-Mause Receiver
I To connect your mouse receiver to a USB mouse port:
1. Locate an available USB mouse port on the back of your computer, i.-
2. Insert the USB mouse port connector into the USB mouse port,
I To connect your mouse receiver to a PSIZ mouu port
1. Locate an available round 6-pin PS/2 mouse port on the back of your compuler
2. Insert the USB connector to PS/2 adaptor.
3, Then plug it into the round 6—pin PS/2 mouse port W 4“
Locating the RF-Mouse Receiver
Your RF-Mouse has limitations on the range ordisunce from the receiver. To make sure that your mouse
sends and receives properly, refer lo the following:
1. For oprinnu performance, place the receiver u least 3 inches (20 centimeters) away from other
electrical devices, such as the computer, the monnor, or external slomge drives.
2. The RF-Mouse should be no farther Ihan 3.3 feet (1.0 meter) from the mouse receiver. This will
ensure Oplirnal communication between the mouse and receiver.
3. ll'you are working on a metallic surface. try using a mouse pad and luming the receiver face
down for belief rcceplion.
4. Switch frequency channels to prevent inlerference from olher RF poxnring devices. (See the
following seclion for more information.)
_——__————
Selecring the Frequency Channel
The RF-Mouse operates on lwo frequency channels. To prevent interference when using lwo
RF Mice in close proximity a different frequency channel should be used for each mouse.
Refer to the followmg to change the frequency channel for your mouse:
1. Set the frequency channel on lhe receiver w l or 2.
2. Remove Ihe battery cover from the mouse (see (be following Inserting [he Batteries
section).
3. set the frequency channel on the mouse to l or 2. (The frequency channel for mouse and
receiver must be the same.)
Inserting the Batteries
The RF-Monse uses two AA batteries. For best perfomwnce, use only alkaline bauenes. Refer
to the following in insert the batteries:
1. Press the lab on the bottom oflhe mouse cover as shown here and remove the Cover.
2. Insen the two AA batteries. (The correct polarity is indicated on the battery
compartment casing.)
3. Replace the cover.
Checking the Batteries power
To check the hatrery power, right—click the rnouse icon E in the Taskbar.
Choose the “Check RF-Mouse Status" option to display the RF-Mouse
Status Window. The current battery percentage charge is shown.
Installing the Mouse Software
Before you can take advantage of the many features your mouse offers. you rrntst install the driver. The driver
is on the installation diskette that came packaged with your mouse.
Windows 95/98/2000/NT40/ME/XP installation
Connect lhe mouse to your computer.
lnsert the installation diskette into your floppy disk drive.
Click the Sun button and lllen click Run.
In the Run dialog window, type Atlsetnp, where “A" is the letter ofyour floppy disk drive.
"m“?!“r
. Click OK and follow the inslmclions on your screen to comvlele the inslallalion.
The RF-Mause ID code
Each RF-Mouse is assigned a unique ID code at manufacture, so the receiver only picks up the signal from your
mouse and prevents other RF-Mouse radio signals from Dpemllng on your computer. This feature can also he
disabled, allowing other RF-poinling devices to operate your computer.
Connecting the RF-Mouse ID Code
_34
When the driver installation is finished your computer reboots and the RF-
Mouse window (shown on the right) appears.
CONNECT ID: Move the RFeMouse for a few seconds to establish a
commotion, then click Connect ID. The unique ID code ufymn' mouse is
recognized and another RF pointing device will not funetion on your
computer.
Exlt: Click Exit ifno other RF pointing devioes are within 3 meters range
or ifyou want other RF pointing devices to be able to aeeess your
computer.
Changing the RF-Mouse ID Code
You can use a new Rf-Mouse on your computer without changing the Radio receiver; you just need to change the ID
code. Refer to the following:
1. Press [Shin + All + Fl 1] or [Shifl * All + FIZ] to call up the RF-Monse ID (Jude window.
2. Move the RF—Mollse for a few seconds to establish a connection, then click Connect ID.
3. The new ID Code is Connected and the RF-Mouse window closes.
4. Click Exit to close the RF-Mouse ID code windnw.
Identifying Compnnenls
The mouse is designed to fit snugly into your hand. The scroll wheel is positioned on the top allowing for easy
opemlion with the index finger. Standard mouse buttons are positioned to either side oflhe scroll wheels and
can be reached comfortably with the index and ring fingers. A third button is placed under the vertical wheel
and can be easily clicked by pushing down on the wheel.
The following pages will tell you how to configure the sen)" wheels and buttons to suit your Specrfic needs.
Cleaning the Mouse
clean the mouse regularly to ensure efficienl operation. Refer to the following:
Rotate the housing cover counterclockwise until it unlocks and remove it.
Remove the tracking ball.
Wash the (making ball with warm water and soap then allow it to dry.
Use a cotton swab and alcohol to clun the o-aekrng rollers in the housing.
Replace the trucking ball and the housing cover.
Rotate the housing cover clockwise until it lacks in plaee.
P‘Sflfik’N?
USING THE MOUSE
With the iWheelWorks sofiwnre, you have all lhe advantages of the Microsoft lnlelllMouse wheel, and but you can
also scroll in Windaws 95/98/2000/NT.
Your mouse has a wheel; the wheel functions as bolh a wheel and a button. Simply cllck tlre wlreel as you would a
programmnble standard ‘I'hlrd button.
SCROLLING AND ZOOMING WITH THE MOUSE
Tnsk Whit is 7 How to do It?
Wheel Scroll Use wheel Scroll for precise To scroll up, move lhe wheel forward; to scroll down.
up and down movement. move tire whee] buck,
Zoom Use Zoom to either magnify Place the cursor in an application that is Microsolt omce
or demagnify the View ofa 97/2000 compatible. Press and hold (he Ctrl key on lhe
document in an appllcstlon keyboard. then to zoom in, move Ihe wheel forward; to
first suppons it. zoom oul, move the wheel backwards.
AutoScroll UseAancroll in Windows Assign AuloScroll lo a billion on the mouse ilik is no!
95/98/NT/2000 and alrendy assigned.
Microsoft Omce97/2000
Place tire cursor in on application, Press the mouse button
assigned to AutoScroll. The AutoScroll icon nppenls.
Move the mouse once in the direction you wont to scroll.
The farmer you move tile pointer from tire starting poinl,
the faster lhe scrolling.
compatible applications to
scroll through large
documents.
AuwScmll allows you scroll
a document automatically
without having lo move the
mouse continuously.
To stop AuloScroll, press any mouse button.
MOUSE PROPERTIES SETTINGS
From the Mouse Propertles window you cun customize many settings for your
mouse including button assignments, scroll wlreels ind cursor movement. To open
the Mouse Properties window double—click on tire mouse icon in the system tray.
The Mouse l’mperlies window has six labs that are described below.
Syslem Tray
P1133 1m
Buttons Tab
Button Assignments: Click the down arrow to selecl lhe preferred function for each button. (See the
Settings Tab for more information.)
Double Click Speed lncreuse tlle speed for executing a double-click.
Button Configurntlon: Configure your mouse for lelt- or right-hand use. Tire default setting for
buttons 1 and 2 will be reversed.
Pointers Tab
The Pointers tab lets you change tire way lhe cursor appears. Click tire down arrow under §chcme und
cltoose tire setting you wanl. The available pointers for euclr sclreme m slrown in the pane below. You
cun browse lo additional pointers, then create your oval scheme using the Suye A1 button.
Motion Tab
Pointer Speed: Lets you adjusl how fast the cursor moves on the screen,
SnapTo Button: Check this box to automatically have the cursor move (0 the default button in each
new dialog box or window.
Sonar: When this box is checked, pressing and releasing the [Ctri] key will highlight tlte cursor.
Trails: Check this box when you want yourcursor to display pointer trails, This opnon is useful when
using an LCD display that can make the oursordimeult to see.
Settings Tab
Cnmmnnd List: Shows all the available commands (including Userdeiined Command Menus) that you
can assign to either the Neuump or LuckyJump grids.
NetJump (top grid): The Neuump grid groups commonly used Webebrowsing commands, To change
a command, select a new one from the Command List and click on the icon in the grid that you want to
change.
LuckyJump (bottom grid): The LuckyJump grid groups allpurpose commands. To change a
command, select a new on: from the Commznd List and click on the icon in the grid (th you want to
change,
Wheel: Check the Reverxe scrolling direction box to change the scrolling direction when you turn the
scroll wheelt Select the Scroll or Scroll one “page"per scroll uni! mdio bullon to set the scrolling speed
to suit your work habits.
Executing Net Jump Commands
Netlump combines commonly used tasks for Web browsing into one convenient grid and puts them right under
the cursor. To use Netlump, open the Moose Properties window and select the Knitting lab. Assign NclJump
in the drop-down menu or the button you want. Click OK to close the Mouse Plupenles window, Now click
the assigned button to open the Netlump god and execute your command. (See the Settings rob section above
for instmctions on customizing Netlump.)
Executing LuckyJump Commands
Luekytump combines comrrtonly used tasks for Windows environments into one convenient grid 2nd puts them
right under the cursor, To use Luckytump, open the Mouse Properties window and select the Buttons Lub.
Assign LuckyJump in the drop-down menu of the button you want. Click OK to close the Mouse Properties
window. Now click the assigned button to open the LuckyJump grid and execute your command. (See the
Settings Tab section above for inslmclions on customizing Luckylump.)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2003:01:22 09:37:31+08:00
Create Date                     : 2003:01:22 09:36:48+08:00
Creator                         : Acrobat 4.0 Scan Plug-in for Windows
Producer                        : Acrobat 4.0 Scan Plug-in for Windows
Page Count                      : 7
Mod Date                        : 2003:01:22 09:37:31+08:00
Creation Date                   : 2003:01:22 09:36:48+08:00
Metadata Date                   : 2003:01:22 09:37:31+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools