A OK Technology Grand Development ACM-01EL Electronic limiter receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1314278
Application ID	fPayJ0y4N2x6JNqQuzsHgg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.2kB (39977 bits)
Date Submitted	2010-07-20 00:00:00
Date Available	2010-07-20 00:00:00
Creation Date	2010-07-16 13:59:46
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2010-07-16 13:59:46
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	terry

SHENZHEN A-OK TECHNOLOGY GRAND DEVELOPMENT CO, LTD
Electronic limit switch tubular motor operation manual
Program
Switch power off over 10’s, power on motor again, press UP&DOWN together and hold on until motor have
a shake, then release hand, motor is in the condition of program. Within the new 3’s, press PROGRAM
button on transmitter back body for 1’s, motor have a shake again, means program complete.
2. Change direction
After complete program, if press UP or DOWN, the motor running direction is in the opposite direction, need
to change the direction now. Press STOP for 2’s, motor have a shake, change direction complete; (This
operation will be valid only before set UP&DWON limit position; If you want to change direction again,
delete all codes, program again and then operate step2)
3. Set UP limit position
Press UP&DOWN together, motor up running, when arrive to the exact position, press STOP button,
then use UP or DOWN button to micro adjustment limit position, when motor arrive to the exact position,
press STOP for 2’s, motor have a shake, this UP limit position is memorized.
4. Set DOWN limit position
Press PROGRAM on transmitter back for 1’s, motor have a shake, then press UP&DOWN together,
motor down running, when arrive to the exact position, press STOP button, then use UP or DOWN button
to micro adjustment limit position, when motor arrive to the exact position, press STOP for 2’s, motor have
a shake, this DOWN limit position is memorized.
5. Micro adjustment UP/DOWN limit position
If you want to change UP or DOWN limit position, after motor arrived to UP or DOWN limit position, press
UP&DOWN together for 5’s, motor have a shake, and now motor is in the condition of bit adjustment mode,
press UP or DOWN bit by bit, when motor arrived desired position, press STOP for 2’s, motor have a shake
again, means micro adjustment new position complete.
6. Delete code
Switch power on motor over 10’s, then switch power on and press UP&DWON together quickly, motor have a
shake, then motor is in the condition of PROGRAM/DELETE mode, within 3’s press PROGRAM button on the
transmitter back body for 7’s, motor have a shake again, delete all codes complete.
Specifications：
A.
B.
C.
D.
E.
F.
G.
H.
Working voltage（ AC230V ±10% 50/60Hz，AC115V±10% 50/60Hz, DC12V, DC24V）
Built-in side receiver
Precious adjustment limit position
Memory position when power supply recover
Auto redress slip position
Stop once block
Sensor short circuit and open circuit protection
Step operation before set limit position
Add new transmitter memory operation：
Use the memorized transmitter, press STOP for 5’s, motor have a shake, motor is in the condition of micro
adjustment mode, within 3’s press PROGRAM on new transmitter back body, motor have a new shake, program
complete.
SHENZHEN A-OK TECHNOLOGY GRAND DEVELOPMENT CO, LTD
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try correct the interference by one or more of the following measures:
Reorient the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2010:07:16 13:59:46+08:00
Create Date                     : 2010:07:16 13:59:46+08:00
Format                          : application/pdf
Title                           : <4D6963726F736F667420576F7264202D20BFD8D6C6C6F7D3A2CEC4B2D9D7F7CBB5C3F72E646F63>
Creator                         : terry
Document ID                     : uuid:870f48de-3f4d-405f-bec2-bb44376f5be0
Instance ID                     : uuid:d653c07f-8bed-4de1-872e-ef867ead5604
Page Count                      : 2
Author                          : terry

EXIF Metadata provided by EXIF.tools