AAMP of Florida AAMP Global ISBT4 Bluetooth audio with FM transmitter and charger User Manual

AAMP of Flordia, dba AAMP of America Bluetooth audio with FM transmitter and charger

User Manual

BluStream FMConnect your phone to your car for calls and music IN-CAR CONNECTIVITYTech Support:support@isimplesolutions.com866-788-4237WARNING:This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage or malfunction.FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:1. Re-orientate or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected. 4. Consult the dealer or an experienced radio / television technical for help.Notice : The changes or modications not expressly approved by the party responsible compliance could void the user authority to operate the equipment.ISBT42Initial Setup1) Plug the charging end of the BluStream FM into your vehicle’s cigarette lighter port, or 12V power outlet2) The body of the BluStream FM has two important built-in features; a microphone and a control button. a. Attach the body of the BluStream on the dash of the vehicle, using the supplied double-sided tape. NOTE: Location is key. Ideally, the body of the BluStream FM should be placed where it has a clear line-of-sight of the driver. This will provide the best hands-free performance. b. The control button functions are described in the operation section. 3) Pair your Smartphone a. Press and hold the control button on the BluStream FM for 10 seconds to enter pairing mode. The control button on the BluStream FM   willrapidlyashBluewheninpairingmode. b. Open the Bluetooth menu on your smartphone and search for available accessories c. Select the BluStream FM from the list and select “Connect” d. With your Bluetooth phone connected to the BluStream FM, begin playback of music and it will stream to your selected FM radio station. Operation 1) Play your music through your vehicle (FM) a. Slide the selector switch on the BluStream FM, to select one of the 4 available FM transmission stations. For best peformance, select a frequency that is not in use by a local radio station in your area. b. Tune your FM radio to the frequency that matches the selected setting on the BluStream FM. c. Begin music playback on your phone, and the audio will play though the vehicle on the selected frequency.2) Receiving a phone call a. Press the control button once to answer an incoming call, when your phone is ringing. NOTE: you must be on the proper station in order to hear the phone call through the vehicle. Control button The control button on the body of the BluStream FM is used for several different functions, which are described below: - Siri / VR: Press the control button. - Redial: Press the control button twice. - Answer Incoming Phone Call: Press the FM control button, while your phone is ringing. - End call: Press the control button, while in a phone call.USB Charging Port BluStream FM features a 5Volt 1 Amp charging port which can be used to charge your smartphone, or other device. For vehicles equipped with an auxiliary audio input (aux)An audio connection cable is included with the BluStream FM, which allows it to be plugged directly into your vehicle’s auxiliary audio input (if equipped). This will provide superior audio quality, compared to the standard FM output of the BluStream FM. All functions described in the Operation section apply when using the aux connection method. The only difference, is that the radio must be on the auxsource,notaspecicFMfrequency.1) Plug the smaller end of the aux cable into the body of the BluStream FM2) Plug the larger end of the aux cable into your vehicle’s aux input NOTE: When using the aux connection method, the setting of the FM selector switch selection on the BluStream does not matter. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu