ADRF KOREA ADX-HPR-C DAS (Distributed Antenna System) User Manual

ADRF KOREA, Inc. DAS (Distributed Antenna System)

UserManual.wiki >

ADRF KOREA >

ADX HPR C User Manual HTML Version

User Manual



AdvancedRFTechnologies,Inc.  i



ADXDASHPRUserManual

Version0.1







3116WestVanowenSt.

Burbank,CA91505

Tel:818‐840‐8131

Fax:818‐840‐8138

www.adrftech.com



AdvancedRFTechnologies,Inc.  ii



Informationinthisdocumentissubjecttochangewithoutnotice.

AdvancedRFTechnologies,Inc.1996‐2015.

Allrightsreserved.



 Pleasesendcommentsto:



E‐Mail:info@adrftech.com



Phone: (818)840‐8131

  (800)313‐9345

Fax:  (818)840‐8138



 Address:



AdvancedRFTechnologies,Inc.

Attention:TechnicalPublicationsDepartment

3116VanowenSt.

Burbank,CA91505

USA

www.adrftech.com



AdvancedRFTechnologies,Inc.  iii



RevisionHistory



ChangeList

VersionChangelistContents

 



VersionAuthorDescriptionsDate

0.1CCKInitialRelease 05/13/15

 

  

 



AdvancedRFTechnologies,Inc.  iv



TableofContents

1. Introduction......................................................................................................................................................14

1.1 Highlights...................................................................................................................................................14

1.2 HeadEndPartsList....................................................................................................................................15

1.2.1 ADX‐H‐NMS‐PKGPartsList.................................................................................................................15

1.2.2 ADX‐H‐BCUPartsList..........................................................................................................................16

1.2.3 ADX‐H‐RFUPartsList..........................................................................................................................16

1.2.4 ADX‐RACK‐ODUPartsList...................................................................................................................17

1.2.5 ADX‐H‐ODU4‐XPartsList....................................................................................................................17

1.2.6 ADX‐H‐ODU1‐XPartsList....................................................................................................................17

1.3 HighPowerRemoteUnitPartsList............................................................................................................18

1.3.1 ADX‐R‐xxx46/44.8/43M(HPR)PartsList............................................................................................18

1.4 ADXDASQuickView..................................................................................................................................19

1.4.1 HEQuickView....................................................................................................................................19

1.4.3 RUQuickView....................................................................................................................................20

1.5 WarningsandHazards...............................................................................................................................21

2. ADX‐DASConfiguration.....................................................................................................................................24

2.1 ADXDASTopology.....................................................................................................................................24

2.2 Configuration.............................................................................................................................................25

2.2.1 Singlebandormulti‐bandconfiguration(1~8bands)........................................................................25

2.3 ADX‐DASScalability...................................................................................................................................26

3. ADXOverview...................................................................................................................................................

3.1 HeadEnd....................................................................................................................................................27

3.1.1 NMS(NetworkManagementSystem)................................................................................................28

3.1.1.1 LEDs..........................................................................................................................................28

3.1.1.2 EthernetPort............................................................................................................................29

3.1.1.3 Host/RemoteSwitch.................................................................................................................29

3.1.1.4 HEView/RUViewSwitch..........................................................................................................29

3.1.2 RFU(ADX‐H‐RFU‐x).............................................................................................................................30

3.1.2.1 LEDs..........................................................................................................................................30

3.1.2.2 RFPorts

.....................................................................................................................................31

3.1.2.3 CommunicationPort.................................................................................................................31

3.1.3 ChannelCombiner(ADX‐H‐CHC)........................................................................................................31

3.1.3.1 RFports.....................................................................................................................................31

3.1.4 OpticUnit(ADX‐RACK‐ODU,ADX‐H‐ODU4/ADX‐H‐ODU1).................................................................32

3.1.4.1 LEDs..........................................................................................................................................32

3.1.4.2 RFPorts.....................................................................................................................................32

3.1.4.3 OpticPorts................................................................................................................................33



AdvancedRFTechnologies,Inc.  v



3.1.4.4 CommunicationPort.................................................................................................................33

3.1.5 PowerSupplyUnit(ADX‐H‐PSU).........................................................................................................33

3.1.5.1 LEDs..........................................................................................................................................33

3.1.5.2 ACInputOn/OffSwitch,ACInputPortandACInputSelectionSwitch....................................34

3.1.5.3 BatteryBackupPort,BatteryInstallPortandBatteryBackupSwitch......................................34

3.1.6 OptionalBandCombinerUnit(ADX‐H‐BCU‐x)...................................................................................35

3.1.6.1 LEDs..........................................................................................................................................35

3.1.6.2 RFPorts.....................................................................................................................................36

3.1.6.3 CommunicationPort.................................................................................................................36

3.2 HPR............................................................................................................................................................36

3.2.1 Port.....................................................................................................................................................36

3.2.1.1 RFPort......................................................................................................................................36

3.2.1.1.1 Antennaserverport(DINtype)..............................................................................................36

3.2.1.1.2 ExtensionFilterport(Ntype).................................................................................................37

3.2.1.2 Opticport..................................................................................................................................37

3.2.1.3 GUI,RS485port.......................................................................................................................38

3.2.2 LEDs....................................................................................................................................................38

3.2.3 ACOn/OffSwitch,ACPort..................................................................................................................39

3.2.4 DCOn/OffSwitch,DCPort.................................................................................................................40

4. CableConnection..............................................................................................................................................41

4.1 HeadEndConnectionDiagrams................................................................................................................41

4.1.1 Front/RearHeadEndConnectionViewwithOptionalBCUunit........................................................41

4.1.2 RearHeadEndConnectionViewwith(4)ADX‐RACK‐ODUunits.......................................................42

4.2 HighPowerRemoteUnitConnectionDiagrams........................................................................................43

5. Mountingmethod.............................................................................................................................................44

5.1 HeadEnd....................................................................................................................................................44

5.1.1 RackMount........................................................................................................................................44

5.1.2 WallMount.........................................................................................................................................45

5.2 HPR............................................................................................................................................................46

5.2.1 WallMount.........................................................................................................................................46

6. Installation........................................................................................................................................................46

6.1 Pre‐InstallationInspection.........................................................................................................................46

6.2 ADXDASInstallationProcedure................................................................................................................47

6.2.1 HEInstallationProcedure...................................................................................................................47

6.2.1.1 InstallingaADXDASHEinarack..............................................................................................47

6.2.1.2 WallmountingtheADXDASHE................................................................................................49

6.2.2 RUInstallationProcedure...................................................................................................................51

6.3 Grounding..................................................................................................................................................53

6.4 OpticPortCleaning....................................................................................................................................54



AdvancedRFTechnologies,Inc.  vi



7. Commissioning..................................................................................................................................................55

7.1 Pre‐CommissioningCheck.........................................................................................................................55

7.1.1 Verifycableconnections....................................................................................................................55

7.1.2 ConnecttotheWeb‐GUI....................................................................................................................55

7.1.3 CheckNavigationTreeStatus.............................................................................................................56

7.1.4 SetLocationInfo,InstallerInfoandDate&Time...............................................................................56

7.1.5 VerifyNavigationTreeLinks...............................................................................................................56

7.1.6 BOMComparison&CheckBandConfiguration.................................................................................57

7.1.7 Lockcurrentnavigationtree..............................................................................................................57

7.2 Commissioning...........................................................................................................................................58

7.2.1 OpticCommissioning..........................................................................................................................58

7.2.1.1 Howtocompensatetheopticloss...........................................................................................58

7.2.2 HECommissioning..............................................................................................................................60

7.2.2.1 Compositepower.....................................................................................................................60

7.2.3 HPRCommissioning............................................................................................................................66

7.3 DASInstallVerification..............................................................................................................................67

7.3.1 SettingSNMP&RemoteIP.................................................................................................................67

7.3.2 VerificationthroughWebbasedGUI.................................................................................................67

7.3.3 ULnoisepowerdetection..................................................................................................................67

8. Web‐GUI...........................................................................................................................................................68

8.1 Web‐GUISetup..........................................................................................................................................68

8.1.1 DASsystem/PCConnectionUsingWeb‐GUI......................................................................................68

8.2 Administrator/UserMode.........................................................................................................................69

8.2.1 Common.............................................................................................................................................69

8.2.1.1 NavigationtreeLock/Unlock....................................................................................................69

8.2.1.2 NavigationTree........................................................................................................................69

8.2.1.3 PowerStatus.............................................................................................................................70

8.2.1.4 CommissioningStatus...............................................................................................................70

8.2.1.5 Information...............................................................................................................................70

8.2.2 StatusTab...........................................................................................................................................71

8.2.2.1 Status–NMS............................................................................................................................71

8.2.2.2 Status–BCU.............................................................................................................................74

8.2.2.3 Status–RFU..............................................................................................................................76

8.2.2.4 Status–ODU.............................................................................................................................78

8.2.2.5 Status–RUHub........................................................................................................................81

8.2.2.6 Status–Remotemodule..........................................................................................................82

8.2.3 ControlTab.........................................................................................................................................85

8.2.3.1 Control–NMS..........................................................................................................................85



AdvancedRFTechnologies,Inc.  vii



8.2.3.2 Control–BCU...........................................................................................................................86

8.2.3.3 Control–RFU............................................................................................................................87

8.2.3.4 Control–ODU...........................................................................................................................91

8.2.3.5 Control–RHHub......................................................................................................................92

8.2.3.6 Control–RemoteModule(MasterorSlaveRU)......................................................................93

8.2.4 InstallTab...........................................................................................................................................96

8.2.4.1 Install–NMS.............................................................................................................................96

8.2.4.2 Install–BCU..............................................................................................................................99

8.2.4.3 Install–RFU............................................................................................................................100

8.2.4.4 Install–ODU...........................................................................................................................102

8.2.4.5 Install–HPRHub....................................................................................................................103

8.2.4.6 Install–RemoteModule(MasterorSlaveRU)......................................................................104

8.2.5 System..............................................................................................................................................106

8.2.5.1 System:Account.....................................................................................................................106

8.2.5.2 System:Logs...........................................................................................................................107

8.2.5.3 System:Update......................................................................................................................108

8.2.5.4 System:SystemInformation...................................................................................................109

8.2.5.5 System:Backup/Restore.........................................................................................................110

8.2.5.6 System:SNMP.........................................................................................................................112

8.2.5.7 System:CloseoutPackage......................................................................................................113

8.2.6 Help..................................................................................................................................................114

8.2.7 Logout...............................................................................................................................................114

8.3 GuestMode.............................................................................................................................................114

9. System‐WideSpecification(tobeconnectedtoHEviaOpticline)................................................................115

700LTE/CELL/SMR800 Specifications...........................................................................................................115

2. PCS/AWS/BRS Specifications....................................................................................................................116

3. SMR900 Specifications...............................................................................................................................117

4. WCS Specifications.....................................................................................................................................118

10. MechanicalDrawing.......................................................................................................................................119







AdvancedRFTechnologies,Inc.  viii



Figures

Figure1‐1 ADXDASHEQuickView.....................................................................................................................19

Figure1‐2 ADXDASHPRQuickView...................................................................................................................20

Figure2‐1 ADXDASBlockDiagram(4BANDS)...................................오류!책갈피가정의되어있지않습니다.

Figure2‐2 ADXDASTopology..............................................................................................................................24

Figure2‐3 ADXDAS3bandsConfiguration..........................................................................................................25

Figure2‐4 ADXDAS4bandsConfiguration........................................오류!책갈피가정의되어있지않습니다.

Figure3‐1 HeadEndFrontView..........................................................................................................................27

Figure3‐2 ADX‐H‐NMSFrontView......................................................................................................................28

Figure3‐3 NMSLED.............................................................................................................................................28

Figure3‐4 EthernetPort......................................................................................................................................29

Figure3‐5 Host/RemoteSwitch...........................................................................................................................29

Figure3‐6 HEView/RUViewSwitch....................................................................................................................29

Figure3‐7 RFUFront&RearView.......................................................................................................................30

Figure3‐8 RFULED..............................................................................................................................................30

Figure3‐9 CommunicationPort(RFU).................................................................................................................31

Figure3‐10 ADX‐H‐CHCFront&RearView...........................................................................................................31

Figure3‐11 ADX‐RACK‐ODUFront&Rearview....................................................................................................32

Figure3‐12 ADX‐H‐ODU4andADX‐H‐ODU1InstalledinADX‐RACK‐ODU............................................................32

Figure3‐13 ADX‐RACK‐ODULED............................................................................................................................32

Figure3‐14 ODURFPorts......................................................................................................................................32

Figure3‐15 ODUOpticPorts.................................................................................................................................33

Figure3‐16 CommunicationPort(ODU)................................................................................................................33

Figure3‐17 ADX‐H‐PSUFront&RearView...........................................................................................................33

Figure3‐18 HEPSULED.........................................................................................................................................34

Figure3‐19 HEPSUACInputOn/OffSwitch,ACInputPortandACInputSelectionSwitch.................................34

Figure3‐20 BatteryBackupPort,BatteryInstallPortandBatteryBackupSwitch................................................34

Figure3‐21 ADX‐H‐BCUFront&RearView...........................................................................................................35

Figure3‐22 BCULED..............................................................................................................................................35

Figure3‐23 CommunicationPort(BCU)................................................................................................................36

Figure3‐24 ADX‐HPRSingleenclosure(bottomview)..........................................................................................36

Figure3‐25 InnerOpticportconnection...............................................................................................................37

Figure3‐26 Opticconnection................................................................................................................................38

Figure3‐27 ADX‐HPR3bandsGUIconnection(Singleenclosure).........................................................................38

Figure3‐28 ADX‐HPR4bandsGUI,RS485connection(2enclosures)오류!책갈피가정의되어있지않습니다.

Figure3‐29 HPRLED..............................................................................................................................................39

Figure3‐30 HPRACPort........................................................................................................................................39

Figure3‐31 HPRACSwitch....................................................................................................................................39

Figure4‐1 HECableconnection(1ADX‐RACK‐ODU+1BCU)..............................................................................42

Figure4‐2 HECableconnection(4ADX‐RACK‐ODUs)..........................................................................................43

Figure4‐3 ADX‐HPR3bandsconnection(Singleenclosure)................................................................................43

Figure4‐4 ADX‐HPR4bandsconnection(2enclosures)....................오류!책갈피가정의되어있지않습니다.

Figure5‐1 HERackMount(Front&Rearview)...................................................................................................44

Figure5‐2 HEWallMount(TopView).................................................................................................................45

Figure5‐3 HPRWallMount.................................................................................................................................46

Figure6‐1 ADXHE19”RackMountInstructions.................................................................................................48

Figure6‐2 ADXHEWallMountInstructions........................................................................................................49

Figure6‐3 WallMountInstructionsforADX‐HEadded1UUnit..........................................................................50

Figure6‐4 HPRWallMountInstructions.............................................................................................................52



AdvancedRFTechnologies,Inc.  ix



Figure6‐5 GroundCableConnection(HErearside)............................................................................................53

Figure6‐6 GroundCableConnection(HPRdualside).........................................................................................53

Figure6‐7 OpticConnectorCleaning(left)andOpticPortCleaning(right)........................................................54

Figure6‐8 SC/APCOpticConnectorDustCap.....................................................................................................54

Figure7‐1 Loginwindow......................................................................................................................................55

Figure7‐2 NavigationtreeLock/Unlock..............................................................................................................56

Figure7‐3 Navigationtree...................................................................................................................................56

Figure7‐4 ODUInstallpage.................................................................................................................................58

Figure7‐5 measuredopticlossdisplay................................................................................................................58

Figure7‐6 BCUInstallWindow............................................................................................................................64

Figure7‐7 RFUInstallWindow............................................................................................................................65

Figure7‐8 RemoteModuleInstallWindow.........................................................................................................66

Figure8‐1 Loginscreen........................................................................................................................................68

Figure8‐2 NavigationtreeLock/Unlock..............................................................................................................69

Figure8‐3 Navigationtree...................................................................................................................................69

Figure8‐4 ADXDASGeneralInformation............................................................................................................70

Figure8‐5 Status‐NMS.......................................................................................................................................71

Figure8‐6 SystemSummary................................................................................................................................71

Figure8‐7 Systemscantime,HEview/RUview...................................................................................................72

Figure8‐8 HEalarmstatus...................................................................................................................................72

Figure8‐9 HECommissioningstatus...................................................................................................................73

Figure8‐10 Status–BCU.......................................................................................................................................74

Figure8‐11 Status–BCUBand..............................................................................................................................74

Figure8‐12 Status–BCUPower&Atten...............................................................................................................74

Figure8‐13 Status–BCUPowerRatio...................................................................................................................75

Figure8‐14 Status–BCUAlarm.............................................................................................................................75

Figure8‐15 Status–RFU........................................................................................................................................76

Figure8‐16 Status–RFUBand...............................................................................................................................76

Figure8‐17 Power&GainDisplay(Admin)...........................................................................................................76

Figure8‐18 Power&GainDisplay(User)..............................................................................................................77

Figure8‐19 Status‐ODU.......................................................................................................................................78

Figure8‐20 Summary(Status–ODU)....................................................................................................................78

Figure8‐21 RFStatus(Status–ODU)....................................................................................................................79

Figure8‐22 OpticStatus(Status–ODU)................................................................................................................79

Figure8‐23 OpticAttenuation(Status–ODU)......................................................................................................80

Figure8‐24 OpticPathStatus(Status–ODU).......................................................................................................80

Figure8‐25 Status‐HPRHub.................................................................................................................................81

Figure8‐26 RUAlarmStatus(Status‐HPRHub)...................................................................................................81

Figure8‐27 RUCommissioningStatus(Status‐HPRHub)....................................................................................81

Figure8‐28 Status–RemoteModule....................................................................................................................82

Figure8‐29 PCSBandInformation(Status–RemoteModule).............................................................................83

Figure8‐30 Power&Gain(Admin)........................................................................................................................83

Figure8‐31 Power&Gain(User)...........................................................................................................................83

Figure8‐32 OpticPower(Status–MasterHPRonly)............................................................................................84

Figure8‐33 Control‐NMS.....................................................................................................................................85

Figure8‐34 Heartbeat(Control–NMS).................................................................................................................85

Figure8‐35 HESystemReboot&FactorySetting(Control–NMS).......................................................................85

Figure8‐36 NMSSystemReboot&FactorySetting(Control–NMS)...................................................................85

Figure8‐37 Control–BCU.....................................................................................................................................86

Figure8‐38 Control–BCUManualATTControl....................................................................................................86

Figure8‐39 Control–BCUReboot/FactorySetting...............................................................................................87

Figure8‐40 Control–BCUAlarmSetting...............................................................................................................87

Figure8‐41 Control‐RFU......................................................................................................................................87



AdvancedRFTechnologies,Inc.  x



Figure8‐42 GeneralSetting(Control–RFU)(Admin)............................................................................................88

Figure8‐43 GeneralSetting(Control–RFU)(User)...............................................................................................88

Figure8‐44 Reboot&FactorySetting(Control–RFU)..........................................................................................88

Figure8‐45 ULNoiseDetection(Control–RFU)...................................................................................................88

Figure8‐46 ULNoiseDetection‐PCSband...........................................................................................................89

Figure8‐47 ManualAttenuatorControlSetting(Control–RFU)..........................................................................89

Figure8‐48 AlarmThresholdSetting(Control–RFU)...........................................................................................90

Figure8‐49 Control–ODU.....................................................................................................................................91

Figure8‐50 OpticAttenuation–ODU....................................................................................................................91

Figure8‐51 Reboot&factorySetting(Control–ODU).........................................................................................92

Figure8‐52 Control–HPRHub..............................................................................................................................92

Figure8‐53 Reboot&FactorySetting(Control–HPRHub)..................................................................................92

Figure8‐54 Control–RemoteModule..................................................................................................................93

Figure8‐55 GeneralSetting(Control‐RU)...........................................................................................................93

Figure8‐56 Reboot&factorySetting(Control‐RU).............................................................................................94

Figure8‐57 OpticSetting(Control‐RU)................................................................................................................94

Figure8‐58 ManualAttenControl(Control‐RU)..................................................................................................94

Figure8‐59 AlarmSetting(Control‐RU)...............................................................................................................95

Figure8‐60 Install‐NMS.......................................................................................................................................96

Figure8‐61 HECommissioningStatus(Install–NMS)...........................................................................................96

Figure8‐62 SNMP(Install–NMS)..........................................................................................................................97

Figure8‐63 LocationSetting(Install–NMS).........................................................................................................97

Figure8‐64 ExternalModemBoxSetting(Install–NMS).....................................................................................97

Figure8‐65 Description(Install–NMS).................................................................................................................98

Figure8‐66 SNMPAgentFalseAlarmTest(Install–NMS)....................................................................................98

Figure8‐67 LocationInfo/InstallerInfo(Install–NMS).......................................................................................98

Figure8‐68 Date&TimeSetting(Install–NMS)...................................................................................................99

Figure8‐69 Install–BCU........................................................................................................................................99

Figure8‐70 Install–BCUCommissioning............................................................................................................100

Figure8‐71 Install–BCUDescription..................................................................................................................100

Figure8‐72 Install‐RFU.......................................................................................................................................101

Figure8‐73 RFUCommissioning(Install–RFU)...................................................................................................102

Figure8‐74 Description(Install–RFU)................................................................................................................102

Figure8‐75 Install–ODU.....................................................................................................................................102

Figure8‐76 Opticcontrol(Control–ODU)..........................................................................................................103

Figure8‐77 Description(Install–ODU)...............................................................................................................103

Figure8‐78 Install‐RUHub...................................................................................................................................104

Figure8‐79 RUCommissioningStatus(Install‐RUHub)......................................................................................104

Figure8‐80 Description(Install‐RUHub).............................................................................................................104

Figure8‐81 Install‐RemoteModule.....................................................................................................................105

Figure8‐82 RUOutputCommissioning(Install‐RU)............................................................................................105

Figure8‐83 Description(Install‐RemoteModule)...............................................................................................106

Figure8‐84 AccountManagement......................................................................................................................106

Figure8‐85 NewAccount....................................................................................................................................106

Figure8‐86 ChangePassword..............................................................................................................................107

Figure8‐87 EventLog..........................................................................................................................................107

Figure8‐88 UserLog............................................................................................................................................108

Figure8‐89 Systemupdate..................................................................................................................................108

Figure8‐90 MessageafterSystemupdateiscomplete.......................................................................................109

Figure8‐91 SystemInformation..........................................................................................................................109

Figure8‐92 SystemNotification..........................................................................................................................110

Figure8‐93 Billofmaterial..................................................................................................................................110

Figure8‐94 SettingBackup(Before)....................................................................................................................111



AdvancedRFTechnologies,Inc.  xi



Figure8‐95 SettingBackup(After).......................................................................................................................111

Figure8‐96 SettingRestore.................................................................................................................................112

Figure8‐97 SNMPV1/V2.....................................................................................................................................112

Figure8‐98 SNMPV3...........................................................................................................................................113

Figure8‐99 System‐CloseoutPackage................................................................................................................113

Figure8‐100 System‐CloseoutPackageafterthefileupload...............................................................................113

Figure8‐101 Help..................................................................................................................................................114

Figure10‐1 HEDrawing.......................................................................................................................................119

Figure10‐2 MasterHPRDrawing.........................................................................................................................120



AdvancedRFTechnologies,Inc.  xii



Tables

Table1‐1 ADX‐H‐NMSPartsList.........................................................................................................................15

Table1‐2 ADX‐H‐BCUPartsList..........................................................................................................................16

Table1‐3 ADX‐H‐RFUPartsList..........................................................................................................................16

Table1‐4 ADX‐RACK‐ODUPartsList...................................................................................................................17

Table1‐5 ADX‐H‐ODU4PartsList.......................................................................................................................17

Table1‐6 ADX‐H‐ODU1PartsList.......................................................................................................................17

Table1‐7 MainHPRPartsList.............................................................................................................................18

Table1‐8 ExtendedHPRPartsList....................................................오류!책갈피가정의되어있지않습니다.

Table2‐1 ADX‐DASScalability............................................................................................................................26

Table3‐1 NMSLEDSpecifications......................................................................................................................28

Table3‐2 RFULEDSpecifications.......................................................................................................................30

Table3‐3 ODULEDSpecifications......................................................................................................................32

Table3‐4 HEPSULEDSpecifications..................................................................................................................34

Table3‐5 BCULEDSpecifications.......................................................................................................................35

Table3‐6 MasterHPRLEDSpecifications...........................................................................................................39

Table7‐1 Opticlosscompensationtable...........................................................................................................59

Table7‐2 Back‐offvalueforeachtechnologyduetotrafficbreathing..............................................................60

Table7‐3 Inputsignalconditions@HERFUdownlinkinput..............................................................................61

Table7‐4 HEmaximumdownlinkinputlevelwithout10dBattenuator............................................................61

Table7‐5 HEdownlinkinputsignalconditionsafteradding10dBattenuatortoHEdownlinkinputport........61

Table7‐6 HEmaximumdownlinkinputlevelafteradding10dBattenuatortoHEdownlinkinputport..........62

Table7‐7 Inputsignalconditions@HEBCUdownlinkinput..............................................................................62

Table7‐8 HEmaximumdownlinkinputlevel.....................................................................................................62

Table7‐9 Targetedmaximuminputpower........................................................................................................62

Table7‐10 MaximumOutputPowerpercarrier..................................................................................................63

Table8‐1 AccountInformationforLogin...........................................................................................................68

Table8‐2 Navigationtree...................................................................................................................................69

Table8‐3 PowerSupplyStatus...........................................................................................................................70

Table8‐4 CommissioningICON..........................................................................................................................70

Table8‐5 SystemSummaryDescription.............................................................................................................72

Table8‐6 DescriptionforHECommissioningstatus...........................................................................................73

Table8‐7 DescriptionforNMSalarm.................................................................................................................73

Table8‐8 RFUAlarmStatus................................................................................................................................77

Table8‐9 SummaryDescription.........................................................................................................................79

Table8‐10 Descriptionforopticpathstatus........................................................................................................80

Table8‐11 DescriptionforHPRCommissioningstatus........................................................................................82

Table8‐12 AlarmStatus(Status‐HPRHub).........................................................................................................82

Table8‐13 OperatingStatus(Status–RemoteModule)......................................................................................84

Table8‐14 DescriptionforGeneralSetting..........................................................................................................88

Table8‐15 DescriptionforMainGainControlSetting(Control–RFU)................................................................89

Table8‐16 DescriptionforAlarmThresholdSetting(Control–RFU)...................................................................90

Table8‐17 DescriptionforOpticAttenuation(Control–ODU)...........................................................................92

Table8‐18 DescriptionforGeneralSetting(Control‐RU)...................................................................................93

Table8‐19 DescriptionforOpticSetting(Control‐RU).......................................................................................94

Table8‐20 DescriptionforManualAttenControl(Control‐RU).........................................................................95

Table8‐21 DescriptionforHECommissioningStatus(Install–NMS)..................................................................96

Table8‐22 DescriptionforOpticcontrol(Control–ODU).................................................................................103

Table8‐23 DescriptionforHPRCommissioningstatus......................................................................................104



AdvancedRFTechnologies,Inc.  xiii



TermsandAbbreviations



Thefollowingisalistofabbreviationsandtermsusedthroughoutthisdocument.

Abbreviation/TermDefinition

AGCAutomaticGainControl

ALCAutomaticLevelControl

AROMSADRF’RepeaterOperationandManagementSystem

BCUBandCombinerUnit

BTSBaseTransceiverStation

CDMACodeDivisionMultipleAccess

CHCChannelcombiner

CWContinuousWave(un‐modulatedsignal)

DASDistributedAntennaSystem

DLDownlink

DownlinkThepathcoveredfromtheBaseTransceiverStation(BTS)tothesubscribers’service

areaviatherepeater

HEHeadEnd

HPAHighPowerAmplifier

HWHardware

IFIntermediateFrequency

LNA LowNoiseAmplifier

LTELongTermEvolution

MSMobileStation

NMSNetworkManagementSystem

ODUOpticDistributionUnitwhichislocatedinADX‐RACK‐ODU.AnADX‐RACK‐ODUhastwo

ODUs.

OEUOpticExpansionUnit

PLLPhasedLockedLoop

PSUPowerSupplyUnit

RFRadioFrequency

RFURFChannelUnit

RURemoteUnitwhichiscomposedofmasterHPRandmultipleslavesRU

HPR HighPowerRU

RemoteModulegenerictermformasterHPRandMasterRU,slaveRU

SWSoftware

ULUplink

UplinkThepathcoveredfromthesubscribers’serviceareatotheBaseTransceiverStation(BTS)

viatherepeater

VSWRVoltageStandingWaveRatio





AdvancedRFTechnologies,Inc.  14



1. INTRODUCTION

Upto(8)frequencybandsinonebody:CurrentlytheADXsupports700MHz(LowerA,LowerB,LowerC,

andUpperC),700MHzPublicSafety&UpperDsupport,Cellular,PCS,SMR800/SMR900,AWS,WCSand

BRS‐TDLTEbands.



ADX‐HPR‐7F43,ADX‐HPR‐C43,ADX‐HPR‐W,ADX‐HPR‐P46,ADX‐HPR‐A46,ADX‐HPR‐BT46



1.1 Highlights

 ModularStructure(HE)

‐ Supportsmultibandsservice(700MHz,700MHzPS,Cell,PCS,AWS,SMR800/SMR900,WCS,BRS‐

TDLTE,etc.)inonebody

‐ Supportsupto8RFunits

 Supportsoptionalcombining/balancingofmultiplecarriers’signalsviaBCU(BandCombinerUnit)

 Supportsuptoaofmaximumof8HighPowerRemoteUnits

 Upto6BandinHPRenclosure

 46/44.8/43dBmofdownlinkcompositeoutputpower

 Requiresonlysinglestrandoffiberperremoteunit

 Operateswithupto5dBoopticalloss(withADX‐H‐ODU4,singlemode),upto10dBoopticallosspossible(with

ADX‐H‐ODU1,singlemode)

 SupportsSNMPv1,v2,v3(get,set&traps)

 Web‐basedGUIInterface;No3rdpartyGUIsoftwarerequired

 Web‐GUIconnectivityviaDHCPinhostmode

 VersatilityandUsability:ADXgivestotalcontroltotheuser.Controlparameterssuchasgain,outputpower,

andalarmthresholdcanbechangedusingWeb‐GUIinterfaceallowingtheusertofinetunethesystemtothe

givenRFenvironment.

 Uplinknoisemeasurementroutine

 SupportRUViewmode,refertosection3.1.1.4

 IncrementalAutomaticShutdown/ResumeTime:ADXgraduallyincreasesthetimespanbetweenautomatic

shutdownandresumeperiodbeforeitpermanentlyshutsitselfdown

 SupportALCfunctiontopreventADXDASfrominputoverloadoroutputoverpower



메모 [C1]: 표기방법검토

W43‐>W44.8‐>W 로수정

메모 [C2]: 수정

메모 [H3]: 8‐>6 로수정



AdvancedRFTechnologies,Inc.  15



1.2 HeadEndPartsList

1.2.1 ADX‐H‐NMS‐PKGPartsList

Table1‐1ADX‐H‐NMSPartsList

LabelQuantityDescription



A

ADX‐H‐NMS‐PKG(NetworkManagementSystemPackage)

1ADX‐H‐NMS

1ADX‐H‐PSU(ACtoDCSupply)

1ADX‐H‐CHC(HeadEndChannelCombiner)

B1ACPowerCord

C1RJ‐45CrossoverCable

D1GroundCable

E1DocumentationCD(UserManual,QuickStartGuideandTroubleshootingGuide)

F1WallAnchorBoltSet

G28SMAterminators

H1L‐mountingBrace



B. C. D. E. F.

G. H.



AdvancedRFTechnologies,Inc.  16



1.2.2 ADX‐H‐BCUPartsList

Table1‐2ADX‐H‐BCUPartsList

LabelQuantityDescription

A1ADX‐H‐BCU(BandCombinerUnit)

B6N‐Typeterminators

C2NMtoNMRFJumperCables(3ft)

D1Data/PowerCable

E2Chassismountingbrace

B. C. D. E.

1.2.3 ADX‐H‐RFUPartsList

Table1‐3ADX‐H‐RFUPartsList

LabelQuantityDescription

A1ADX‐H‐RFU(RFUnit)

B2N‐TypeTerminators

C2SMAMaleRFJumperCables

A. B. C.



AdvancedRFTechnologies,Inc.  17



1.2.4 ADX‐RACK‐ODUPartsList

Table1‐4ADX‐RACK‐ODUPartsList

LabelQuantityDescription

A1ADX‐RACK‐ODU

B1Data/PowerCable

C1ChassisMountingBrace

B. C.

1.2.5 ADX‐H‐ODU4‐XPartsList

Table1‐5ADX‐H‐ODU4PartsList

LabelQuantityDescription

A1ADX‐H‐ODU4(4‐portOpticalUnit)

B2SMA‐MTerminators

C2SMA‐MtoSMA‐MRFJumperCable(3ft)

B. C.

1.2.6 ADX‐H‐ODU1‐XPartsList

Table1‐6ADX‐H‐ODU1PartsList

LabelQuantityDescription

A1ADX‐H‐ODU1(1‐portOpticalUnit)

B2SMA‐MTerminators

C2SMA‐MtoSMA‐MRFJumperCable(3ft)

메모 [H4]: ‐X추가

메모 [H5]: ‐X추가



AdvancedRFTechnologies,Inc.  18



B. C.

1.3 HighPowerRemoteUnitPartsList

1.3.1 ADX‐R‐xxx46/44.8/43M(HPR)PartsList

Table1‐7HPRPartsList

LabelQuantityDescription

A1ADX‐R‐xxx46/44.8/43M(MainHPR)

B4Ntype‐Mterminators

C1USBCable

D1ACcable

E1Groundcable

F4AnchorBolt

G1ManualCD

H1Installguide

I1Wallmounttemplate







AdvancedRFTechnologies,Inc.  19



1.4 ADXDASQuickView

1.4.1 HEQuickView

1.4.2 





POWER

SOFT FAIL-H

SOFT FAIL-R

HARD FAIL-H

HARD FAIL-R

LINK FAIL-H

LINK FAIL-R

POWER

CHG STS

LOW BATT

AC FAIL

DC FAIL



19” rackmount

Holes

Host/RemoteSwitch,

HEview/RUviewSwitch

&RJ‐45port

OpticPorts

BatteryBackup

Port

RFUDuplexPort

ACInput&

On/OffSwitch

BCUInterfacePorts

BandCombinerUnit

(BCU)

OpticUnit(ODU)

ChannelCombiner

(CHC)

RFChannelUnit

(RFU)

PowerSupplyUnit

(PSU)

NMSUnit

BatteryBackup

On/OffSwitch

ACInputVoltage

SelectionSwitch

(110V/220V)

RFUSimplex

Port

ODUInterfacePorts

AUXCHInterface

Ports

RFPortsconnectedto

ODU

RFPorts

connectedtoCHC

BCUSumPort

Figure1‐1ADXDASHEQuickView

Groundterminal



AdvancedRFTechnologies,Inc.  20



1.4.3 RUQuickView



BAN D 1 SER VER BAN D2 SER VER

AC IN 110V

A = AC_L

B = AC_N

C = F. G

OPTIC

GUI

EX_F1_IN

EX_F 1_ O U T BAN D 3 SER VER BAN D4 SER VER

CPL

(-30dB)

CPL

(- 30dB )

CPL

(-30 dB )

CPL

( -30dB)

CPL

(- 30dB )

CPL

( -30dB)

BAN D6 SER VERBAN D5 SER VER

PO WER

RUN

EX_F2_O U TEX _F 2_IN

Serverantennaport

AC(DC)port

Opticport

Filterextensionport_2

LocalGUIport

Fanunit

Filterextensionport_1

Groundterminal



Figure1‐2ADXDASHPRQuickView

Controllerperband

RAU

Duplexer

HPA

ORU

RCU

Opticport

PSU

SplitterUnit

메모 [C6]: 사진수정필요

메모 [C7]: 수정해당도면그림의경우

김현기선임이추가해주시기바랍니다.



AdvancedRFTechnologies,Inc.  21



1.5 WarningsandHazards







OpeningortamperingtheADXDASwillvoidallwarranties.

WARRANTY



Actualseparationdistanceisdeterminedupongainofantennaused.Werecommendthatthemaximumantennagain

shouldnotbeexceed2dBifor698‐960MHzand3dBifor1710‐2690MHz.

RFexposurecomplianceshouldbeaddressedatthetimeoflicensing.



AntennasmustbeinstalledinaccordancewithFCCrule.Theheightoftheantennaaboveaverageterrain

(HAAT)ispermittedover1372m.Fordifferentgainantennasrefertotherelevantrules.

RFEXPOSURE&ANTENNAPLACEMENTGuidelines



WorkingwiththeADXDASwhileinoperation,mayexposethetechniciantoRF

electromagneticfieldsthatexceedFCCrulesforhumanexposure.VisittheFCCwebsiteat

www.fcc.gov/oet/rfsafetytolearnmoreabouttheeffectsofexposuretoRFelectromagnetic

fields.



WARNING!EXPOSURETORF



OpeningtheADXDAScouldresultinelectricshockandmaycause

severeinjury.

WARNING!ELECTRICSHOCK

LithiumBattery:CAUTION.RISKOFEXPLOSIONIFBATTERY ISREPLACEDBY INCORRECTTYPE.

DISPOSEOFUSEDBATTERIESACCORDINGTOINSTRUCTIONS.



AdvancedRFTechnologies,Inc.  22





WANRNING.THISisNOTaCONSUMERdevice.ItisdesignedforinstallationbyFCCLICENSEESand

QUALIFIEDINSTALLERS.YouMUSThaveanFCCLICENSEorexpressconsentofanFCCLicenseeto

operatethisdevice.Unauthorizedusemayresultinsignificantforfeiturepenalties,including

penaltiesinexcessof$100,000foreachcontinuingviolation.



FCCPart20

NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassA

digitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovide

reasonableprotectionagainstharmfulinterferencewhentheequipmentisoperatedina

commercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructionmanual,maycause

harmfulinterferencetoradiocommunications.Operationofthisequipmentinaresidentialarea

islikelytocauseharmfulinterferenceinwhichcasetheuserwillberequiredtocorrectthe

interferenceattheirownexpense.



FCCPart15ClassA

EthernetInstructions:Thisequipmentisforindooruseonly.Allcablingshouldbelimitedto

insidethebuilding.

메모 [H8]: 추가15/5/18

메모 [H9]: 추가15/5/18



AdvancedRFTechnologies,Inc.  23





Useofunauthorizedantennas,cables,and/orcouplingdevicesnotconformingwith

ERP/EIRPand/orindoor‐onlyrestrictionsisprohibited.



Donotremovetheprotectivecoversonthefiberopticconnectorsuntilaconnectionisreadytobe

made.Donotleaveconnectorsuncoveredwhennotconnected.



Thetipofthefiberopticconnectorsshouldnotcomeintocontactwithanyobjectordust.



Refertothecleaningprocedureforinformationonthecleaningofthefibertip.

CareofFiberOpticConnectors



FiberopticportsoftheADXDASemitinvisiblelaserradiationatthe1310,1550nmwavelength

window.



Toavoideyeinjuryneverlookdirectlyintotheopticalports,patchcordsoropticalcables.Do

notstareintobeamorviewdirectlywithopticalinstruments.Alwaysassumeopticaloutputison.



Onlytechniciansfamiliarwithfiberopticsafetypracticesandproceduresshouldperformoptical

fiberconnectionsanddisconnectionsoftheADXDASandtheassociatedcables.



TheADXDAScomplieswith21CFR1040.10and1040.11exceptfordeviationspursuanttolaser

noticeNo.50(July26.2001)@IEC60825‐1,Amendment2(Jan.2001).

LaserSafety



AdvancedRFTechnologies,Inc.  24



2. ADX‐DASCONFIGURATION



2.1 ADXDASTopology

HE(Head End Unit) RU(Remote Unit)

Optic

PCS RFU

(RF Interface Unit

with BTS or BDA)

Cellular RFU

(RF Interface Unit

with BTS or BDA)

AWS RFU

(RF Interface Unit

with BTS or BDA)

BCU(optional)

(Band Combiner Unit

with BTS or BDA)

Service Carrier #1

Service Carrier #2

Service Carrier #3

Service Carrier #1

Service Carrier #2

CHC-H

(HE Channel

Combiner)

700M RFU

(RF Interface Unit

with BTS or BDA)

Service Carrier #2

OPT-H

(RF to Optical)

OPT-H

(RF to Optical)

OPT-H

(RF to Optical)

OPT-H

(RF to Optical)

PCS Master RU

Combiner

Cellular Slave RU

AWS Slave RU

700M Slave RU

PCS Master RU

Combiner

Cellular Slave RU

AWS Slave RU

700M Slave RU

PCS Master RU

Combiner

Cellular Slave RU

AWS Slave RU

700M Slave RU

PCS Master RU

Combiner

Cellular Slave RU

AWS Slave RU

700M Slave RU

OEU

(Optic Expansion

Unit)

PCS Master RU

Combiner

Cellular Slave RU

AWS Slave RU

700M Slave RU

PCS Master RU

Combiner

Cellular Slave RU

AWS Slave RU

700M Slave RU



Figure2‐1ADXDASTopology



메모 [C10]: BlockDiagram삭제(15.07.28)

_조찬기



AdvancedRFTechnologies,Inc.  25



2.2 Configuration

2.2.1 Singlebandormulti‐bandconfiguration(1~8bands)



BAN D 1 SE RVE R BAN D 2 SERVE R

AC IN 11 0V

A = AC _L

B = AC _ N

C = F.G

OPTIC

GUI

EX_F 1_IN

EX_F 1_O U T BAN D 3 SE RVE R BAN D 4 SERVE R

CPL

(-30dB)

CPL

(-30 dB)

CPL

(-30 dB)

CPL

(-30dB)

CPL

(-30 dB)

CPL

(-30dB)

BAN D 6 SERVE RBAN D 5 SERVE R

PO WER

RUN

EX_F2_ OU TEX_F2_ IN

ADX- H-NMS

T FAIL-H

SOFT FA

IL-R

HAR

D FAIL-H

D FAIL-R

LINK FAIL-H

LINK FAIL-R

HOST HE VIEW

REMOTE RU VI EW

DL OUTUL IN

HARD FAIL

DL SIG LOW

S OFT FA I L

POWER

ADX- H-RFU- P

DL OUTUL IN

HARD FAIL

DL SIG LOW

S OFT FA I L

POWER

ADX-H-RFU- 7

DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA IL

POWER

ADX-H -RF U-C

ADX- H-CHC

UL1 UL2 UL3 UL4

DL1 DL2 DL3 DL4

UL5 UL6 UL7 UL8

DL5 DL6 DL7 DL8

ADX- H-PSU

POW

HG STS

W B

C F

AIL

DC F

AIL

LD FAI L LI NK 1 LI NK2 LI NK3 LI NK 4POWER

ADX -RACK-ODU

LD FA IL LI N K1 LIN K 2 LI N K3 LIN K4

ODU2ODU1

700LTE

PCS

CELL

BTS



Figure2‐2ADXDAS6bandsConfiguration

‐ HPRiscomposedofonlyMainHPRfor1~6bandsconfiguration

‐ Inthiscase,HPRhastwoORU.



메모 [C11]: 수정

메모 [C12]: 수정(CK)

메모 [H13]: 8‐>6으로수정함.



AdvancedRFTechnologies,Inc.  26



2.3 ADX‐DASScalability

Table2‐1ADX‐DASScalability

UnitScalabilityRemarks

Supportedband700M,Cellular,AWS,PCS,SMR800/900,

PS700,WCS,BRSTD‐LTE 

HE

RFUUpto8upto6:cardtype

&8

RFU:19”racktype

NMS1

ChannelCombiner1

OpticUnitUpto4

BandCombinerUnitUpto4Tosupportmultiplecarriers

PowerSupplyUnit

(ACorDC)1Capableofsupplyingpowerto8RFUs,4

BCUs,4ODUracksandNMS.

RUorHPR

RUorHPRUpto60

OEUUpto4

PSU

(RU)

Adaptortype1perremotemodule

19”rackmount

(ACorDC)1Capableofsupplyingpowerto6Remote

Modules



메모 [H14]: 8‐>6 으로수정



AdvancedRFTechnologies,Inc.  27



3. ADXOVERVIEW

3.1 HeadEnd

TheheadendunitmustalwaysbeconnectedtotheBaseStationusingadirectcabledconnection.This

systemhasnotbeenapprovedforusewithawirelessconnectionviaserverantennatothebasestation.



Headendcomponentsinclude:

 ADX‐H‐NMS(NetworkManagementSystem)

 ADX‐H‐CHC(HeadEndChannelCombiner)

 ADX‐H‐PSU(HeadEndPowerSupply)

 Upto[4]ADX‐H‐BCU(BandCombinerUnit)

 Upto[8]ADX‐H‐RFU‐x(RFUnit)

 Upto[4]ADX‐RACK‐ODU(OpticalUnit)

 Specifications

‐ Size:19.0x14.6x12.2inches(482x370x311mm)

‐ Weight:83.7lbs(38.0Kg)@4RFU,CHC‐H,PSUandNMS

‐ PowerConsumption:52W@4RFU,1ADX‐H‐ODU4andNMS,28W@1RFU,1ADX‐H‐ODU4and

NMS

‐ PowerInput:110VACor‐48VDC(optional)

‐ SupportstheADRF‐BBUforexternalbatterybackupsolution



ADX- H-NM S

OWE

FT FAIL-H

FT FAIL-R

ARD

IL-H

RD FAIL-R

LINK FAIL -H

LIN K

IL-R

HOST HE VIEW

REMOTE RU VIEW

ADX- H-PSU

OWE

CHG S

LOW

ATT

C FAIL

DC FAIL

DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA I L

POWER

ADX-H -RFU-P

DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA I L

POWER

ADX-H -RFU-7

DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA I L

POWER

ADX-H -RFU-C

DL OUTUL IN

HARD FAIL

DL SIG LOW

SOFT FAIL

POWER

ADX -H- RFU-A

ADX- H-CHC

UL1UL2UL3UL4

DL1DL2DL3DL4

UL5UL6UL7UL8

DL5DL6DL7DL8

LD FA I L5- 8 LI N K5 LI N K 6 LI N K7 LI N K8LD FA I L1- 4 LI N K1 LI N K 2 LI N K3 LI N K4POWER

ADX- H-RACK -ODU

SOFT FAILPOWER

ADX- H-BCU -P



Figure3‐1HeadEndFrontView





메모 [Y15]: 추가

15/05/18



AdvancedRFTechnologies,Inc.  28



3.1.1 NMS(NetworkManagementSystem)

 Functionsandfeatures

‐ SupportsSNMPv1,v2,andv3(get,set&trap)andweb‐basedGUIInterface.

‐ Monitorsalarmsandstatus

‐ Providescontrolinterfaceswithallsubordinatemodules

‐ ProvidesoverallDASstructureviatheautotreeupdatefunction

 Spec

‐ Size:19.0x12.1x1.7inches

‐ Weight:5.5lbs

ADX -H- NM S

OWE

OFT FA

IL-H

OFT FA

IL-R

RD FAIL-H

RD FAIL-R

LIN

K FAIL-H

LIN

K FAIL-R

HOST HE VIEW

REMOTE RU VIEW



Figure3‐2ADX‐H‐NMSFrontView

3.1.1.1 LEDs

NMShasLEDsonthefrontpanelasshowninFigure3‐3.

FT-FA

IL-H

FT-FA

IL-R

D-FAIL-H

D-FAIL-R

LIN K

FAIL-H

LIN K

FAIL-R



Figure3‐3NMSLED



Table3‐1NMSLEDSpecifications

ADXDAS‐NMSSpecifications

PowerSolidGreenNMSpowerisON

OFF NMSpowerisOFF

SOFTFAIL‐HSolidYellowHESoftFailalarmexistsinthesystem

SolidGreenNoHESoftFailalarmsarepresentinthesystem

SOFTFAIL‐RSolidYellowRUSoftFailalarmexistsinthesystem

SolidGreenNoHPRSoftFailalarmsarepresentinthesystem

HARDFAIL‐HSolidRedHEHardFailalarmexistsinthesystem

SolidGreenNoHEHardFailalarmsarepresentinthesystem

HARDFAIL‐RSolidRedRUHardFailalarmexistsinthe system

SolidGreenNoHPRHardFailalarmsarepresentinthesystem

LINKFAIL‐HSolidYellowHELinkFailalarmexistsinthesystem

SolidGreenNoHELinkFailalarmsarepresentinthesystem

LINKFAIL‐RSolidYellowRULinkFailalarmexistsinthesystem

SolidGreenNoHPRLinkFailalarmsarepresentinthesystem







AdvancedRFTechnologies,Inc.  29



3.1.1.2 EthernetPort

TheEthernetportcanbeusedtocommunicatedirectlywiththeADXDASusingaRJ‐45crossovercableorcan

alsobeusedtoconnecttheADXDAStoanexternalmodembox.

HOST HE VIEW

REMOTE RU VIEW



Figure3‐4EthernetPort



3.1.1.3 Host/RemoteSwitch

TheHost/RemoteSwitchallowstheusertoswitchthedefaultRepeaterIP,SubnetMask,andGatewayofthe

repeatertoanalternativesetup.ThesesettingscanbeadjustedbyloggingintotheADXDASinHOSTmodeand

configuringthesettingsundertheModemBoxSettingsectionundertheInstallPageofNMS. 

Oncethesettingsareset,flippingtheswitchtotheREMOTEpositionwillrebootNMSmodulewiththenew

alternatesettings.PleasenotethatwhentheNMSissettotheREMOTEposition,DHCPisdisabledandtheNMS

willnotautomaticallyassignanIPaddresstoanydevicethatconnectsdirectlytotheNMS.



HOST HE VIEW

REMOTE RU VIEW



Figure3‐5Host/RemoteSwitch

 HostIP:192.168.63.1(FixedIP,unabletomodifythisIPaddress)

 RemoteIP:192.168.63.5(DefaultIP,butcanbemodifiedinHostmode)

3.1.1.4 HEView/RUViewSwitch

TheHEView/RUViewSwitchallowstheusertodisabletheperiodicmonitoringperformedbytheNMS.Inthe

HEviewmode,theNMSmonitorsthestatusofallsubordinateunitsconnectedtoNMSbutwhenswitchedtoHPR

viewtheNMSdoesnotmonitorthesubordinateunits.HPRViewmodewillallowtheusertogotoaHPRand

monitor/controltheHE.IftheNMSissettotheHEViewmodeandtriestoconnecttoaHPRtomonitortheHE,

datacollisionsbetweentheNMSandHPRmaypreventtheuserfromproperlymonitoringorconfiguringtheHE

whenattheRU.

HOST HE VIEW

REMOTE RU VIEW



Figure3‐6HEView/RUViewSwitch





AdvancedRFTechnologies,Inc.  30



3.1.2 RFU(ADX‐H‐RFU‐x)



DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA I L

POWER

ADX -H- RFU-P

DL I N UL O UT

DPX

AD X -H- R F U-P



Figure3‐7RFUFront&RearView

 Functionsandfeatures

‐ ProvideRFinterfacewithBTS

‐ EachRFUhasindependentgaincontrolandfiltering

‐ Modulartypeandhotswappable

‐ SupportsduplexportorsimplexTX&RXports

‐ EasilysupportadditionalfrequencybandsbyaddingasingleRFU

‐ Reducescomplexityandoverallequipmentsize

 Specifications

‐ Size:12.8x6.2x2.8inches

‐ Weight:7.3lbs



3.1.2.1 LEDs

RFUhasLEDsonthefrontpanelasshowninFigure3‐8.

HARD FAIL

DL SIG LOW

S O FT FA I L

POWER



Figure3‐8RFULED



Table3‐2RFULEDSpecifications

ADXDAS‐ModuleSpecifications

PowerSolidGreenModulepowerisON.

OFF ModulepowerisOFF.

SoftFailSolidYellowSoftFailalarmexistsintheRFU.

SolidGreenNoSoftFailalarmsarepresentintheRFU.

HardFailSolidRedHardFailalarmexistsintheRFU.

SolidGreenNoHardFailalarmsarepresentintheRFU.

DLSIGLOWSolidYellowWhenDLinputsignallevelislowerthanthedefinedthreshold

level.(defaultthresholdvalue:‐5dBm)

SolidGreenWhenDLinputsignallevelisupperthanthedefinedthreshold

level.



AdvancedRFTechnologies,Inc.  31



3.1.2.2 RFPorts

3.1.2.2.1 DLIN/ULOUT&DPXports

DLIN/ULOUT&DPXPorts(refertoFigure3‐7)arelocatedatthebackofRFUandcanbeconnecteddirectlyto

theBTS.TheRFUcansupportincomingsignalstrengthfrom0to25dBm.

3.1.2.2.2 DLOUT/ULIN

DLOUT/ULINPorts(refertoFigure3‐7)arelocatedatthefrontoftheRFUandconnectdirectlytotheHE

ChannelCombiner(ADX‐H‐CHC).

3.1.2.3 CommunicationPort

TheADX‐H‐NMSmonitorsandcontrolstheRFUviathisport.DCPowerisalsoprovidedtotheRFUviathisport.



Figure3‐9CommunicationPort(RFU)

3.1.3 ChannelCombiner(ADX‐H‐CHC)

ADX -H- CHC

UL1 UL2 UL3 UL4

DL1 DL2 DL3 DL4

UL5 UL6 UL7 UL8

DL5 DL6 DL7 DL8



UL5UL6UL7UL8

DL5DL6DL7DL8

UL1UL2UL3UL4

DL1DL2DL3DL4



Figure3‐10ADX‐H‐CHCFront&RearView

 Functions&Features

‐ CombinesDLsignalsreceivedfromeachRFUandfeedsthecombinedsignalstotheADX‐RACK‐

ODU

‐ CombinesULsignalsreceivedfromeachHPRandfeedsthecombinedsignaltotheADX‐H‐RFU

‐ Supportsupto8RFUsand(4)ADX‐RACK‐ODU

 Specifications

‐ Size:16.9x12.9x1.7inches

‐ Weight:11.0lbs

3.1.3.1 RFports

3.1.3.1.1 RFportsatthefrontpanel(DL1toDL8,UL1toUL8)

DL1(toDL8)&UL1(toUL8)RFportsareconnectedtoDLOUT/ULINPortsatthefrontpanelofRFU.

 ReceivethedownlinksignalfromeachRFU

 SplittheuplinksignalreceivedfromODUtoeachRFU



3.1.3.1.2 RFportsatthebackpanel(DL1toDL8,UL1toUL8)

DL1(toDL8)&UL1(toUL8)RFportsareconnectedtoDLIN/ULOUTPortsatthebackpanelofODU.

 TransferthecombineddownlinksignalstoODU

 ReceivetheuplinksignalfromODU



AdvancedRFTechnologies,Inc.  32



3.1.4 OpticUnit(ADX‐RACK‐ODU,ADX‐H‐ODU4/ADX‐H‐ODU1)



Figure3‐11ADX‐RACK‐ODUFront&Rearview



Figure3‐12ADX‐H‐ODU4andADX‐H‐ODU1InstalledinADX‐RACK‐ODU

 Functions&Features

‐ ConvertssignalfromRFtoopticandtransportssignalsuptoamaximumof10Km(optical5dBo

lossincludingopticalconnectionloss).

‐ ADX‐H‐ODU4‐Xcansupportsupto(4)MainHPRsandupto5dBoopticalloss.

‐ ADX‐H‐ODU1‐Xcansupportsupto10dBoopticalloss.

‐ Minimizesthenumberofopticfibercableneedbytransportingmultibandsignalsoverasingle

strandoffiberusingWDMtechnology.

 Spec

‐ Size:19.0x12.9x1.7inches(482x327x44mm)

‐ Weight:13.2lbs(6.0kg)

3.1.4.1 LEDs

TheADX‐RACK‐ODUhasthefollowingLEDsonthefrontpanelasshowninFigure3‐13.



Figure3‐13ADX‐RACK‐ODULED

Table3‐3ODULEDSpecifications

ADXDAS‐ModuleSpecifications

PowerSolidGreenModulepowerisON

OFF ModulepowerisOFF

LDFAILOFF ODUisnotinstalled

SolidYellowLDFailalarmexistsintheODU

SolidGreenNoLDFailalarmispresentintheODU

LINK1toLINK4SolidYellowPDFailalarmexists

SolidGreenNoPDFailalarmispresent

3.1.4.2 RFPorts

VHF UL 1 U L O U T 1VHF DL 1DL IN 1



Figure3‐14ODURFPorts

OPT

VHF UL UL OUT VHF DL DL IN

LINK 4LINK 3LINK 2LINK 1

VHF UL UL OUT VHF DL DL IN

LINK 4 LINK 3 LINK 2 LINK 1

VHF UL UL OUT VHF DL DL IN

LINK 1

메모 [H16]: ‐X추가

메모 [H17]: ‐X추가



AdvancedRFTechnologies,Inc.  33



3.1.4.2.1 DLIN/ULOUT

ThecombineddownlinksignalreceivedfromADX‐H‐CHCistransferredtotheDLIN1(or2)atthebackofODU.

TheULOUTportconnectsanyoftheportsonbackoftheADX‐H‐CHClabeledUL1~8.



3.1.4.2.2 VHFDL/VHFUL

VHFDL/UHFULportsareusedtosupportPublicSafetyintheVHF&UHFfrequencybands.VHF/UHFsignals

forPublicSafetybypasstheADX‐H‐CHCandconnectdirectlytotheVHFDL/UHFULportsoftheADX‐H‐ODU.

3.1.4.3 OpticPorts

LI N K 4LINK 3LINK 2LINK 1



Figure3‐15ODUOpticPorts

TheADX‐H‐ODU4has(4)opticportsandcansupportupto(4)MainHPR’s.Likewise,theADX‐H‐ODU1has(1)

opticportsandcansupportupto(1)MainHPR.



3.1.4.4 CommunicationPort

ADX‐H‐NMSmonitorsandcontrolstheADX‐RACK‐ODUviathisport.DCpowerisprovidedfromtheADX‐H‐

PSUtotheADX‐RACK‐ODUviathisport.

OPT



Figure3‐16CommunicationPort(ODU)

3.1.5 PowerSupplyUnit(ADX‐H‐PSU)

ADX -H- PSU

OWE

CHG

LOW BATT



OFF



Figure3‐17ADX‐H‐PSUFront&RearView

 Functions&Features

‐ Capableofsupportingupto:

 (8)ADX‐H‐RFUs

 (4)ADX‐H‐BCU

 (4)ADX‐H‐ODU

 ADX‐H‐NMS

‐ SupporttheADRF‐BBUforanexternalbatterybackupsolution

 Specificaitons

‐ Size:16.9x13.1x1.7inches

‐ Weight:7.7lbs

‐ PowerInput:110Vor220VAC,selectablebyswitch

3.1.5.1 LEDs



AdvancedRFTechnologies,Inc.  34



ADX‐H‐PSUhasthefollowingLEDsonthefrontpanelasshowninFigure3‐18.

G STS

LOW

ATT



Figure3‐18HEPSULED

Table3‐4HEPSULEDSpecifications

ADXDAS‐ModuleSpecifications

PowerSolidGreenADX‐H‐PSUpowerisON

OFF ADX‐H‐PSUpowerisOFF

CHGSTSSolidYellowNoACpowerisavailableandADRF‐BBUisbeingused

BlinkingGreenPSUischargingtheADRF‐BBU

SolidGreenADRF‐BBUiscompletelycharged

OFF Batteryisnotconnected

LOWBATTSolidYellowLowBatteryalarmexistinthePSU

SolidGreenNoLowBatteryalarmispresentinthePSU

ACFAILSolidYellowACFailalarmexistsinthePSU

SolidGreenNoACFailalarmispresentinthePSU

DCFAILSolidYellowDCFailalarmexistsintheRFU

SolidGreenNoDCFailalarmsispresentinthePSU

3.1.5.2 ACInputOn/OffSwitch,ACInputPortandACInputSelectionSwitch

ON/OFFAC IN

AC SELECT



Figure3‐19HEPSUACInputOn/OffSwitch,ACInputPortandACInputSelectionSwitch

TheACPoweron/offswitchislocatedatthebackpanelofHEPSU.TheADX‐H‐PSUcanoperateat110VAC

and220VAC.TheusershouldverifythattheACinputvoltageswitchissettothecorrectvoltagebeforepowering

ontheADX‐H‐PSU.

3.1.5.3 BatteryBackupPort,BatteryInstallPortandBatteryBackupSwitch



BATTERY

INSTALL

BATTERY

24V 1A

BATTERY

OFF

S/WOFF ON



Figure3‐20BatteryBackupPort,BatteryInstallPortandBatteryBackupSwitch

TheBatterySwitchcanbeusedtoprovidepowertotheoptionalExternalBackupBattery(ADRF‐BBU)(Figure

3‐20).



TheADX‐H‐PSUcanbeconnectedtoanADRF‐BBU(ADRFBatteryBackupUnit)whichcanprovidepower

duringapoweroutage.IfanADRF‐BBUisutilized,connecttheADRF‐BBUtotheADX‐H‐PSUviatheexternal

batterybackupportasshowninFigure3‐20.



AdvancedRFTechnologies,Inc.  35



(WARNING:ThecircuitswitchontheADRF‐BBUmustbesettotheOFFpositionbeforeconnectingtheADRF‐

BBUtotheADX‐H‐PSUtopreventdamagetotheADX‐H‐PSUortheADRF‐BBUandpersonalinjury.)

Note:PleasecontactADRFTechnicalSupportforassistanceifyouareunfamiliarwiththeinstallation

procedureofourbatterybox.



TheBatteryInstallportisusedtoletADX‐H‐NMSknowifanADRF‐BBUisconnectedtotheADX‐H‐PSUornot.

IfanADRF‐BBUisconnectedwithoutthecableconnectiontoBatteryInstallport,theADX‐H‐NMSwillnotdetect

theADRF‐BBU.



TheprocedureforconnectingHEPSUtoBBU



 BATTS/WOFF

 ConnectADRF‐BBUtoHEPSUBatteryportandBatteryInstallportusingHEbattery

cable

 BATTS/WON



3.1.6 OptionalBandCombinerUnit(ADX‐H‐BCU‐x)

SOFT FAILPOWER

ADX- H-BCU -P



DL IN 3

BAND COM

CH3 CH2 CH1 SUM

DPX 3UL OUT 3DL IN 2DPX 2UL OUT 2DL IN 1 DPX 1UL OUT 1 D L O U T U L I N



Figure3‐21ADX‐H‐BCUFront&RearView

 Functions&Features

‐ Combinesandbalancesupto3carriers’signals

‐ Easilysupportsmultiplecarriers’signalsbyaddingasinglepieceofequipment

‐ Reducescomplexityandexpansioncoststosupportmultiplecarriers’signalsinasinglesystem

‐ Inputrange:+5~+25dBm

 Specifications

‐ Size:19.0x12.9x1.7inches

‐ Weight:9.9lbs

3.1.6.1 LEDs

TheADX‐H‐BCUhasthefollowingLEDsonthefrontpanelasshowninFigure3‐22.

POWER SOFT FAIL



Figure3‐22BCULED

Table3‐5BCULEDSpecifications

ADXDAS‐ModuleSpecifications

PowerSolidGreenModulepowerisON

OFF ModulepowerisOFF

메모 [C18]: BCUH추가필요검토



AdvancedRFTechnologies,Inc.  36



SoftFailSolidYellowSoftFailalarmexistintheRFU

SolidGreenNoSoftFailalarmsarepresentintheRFU

3.1.6.2 RFPorts

3.1.6.2.1 DLIN/ULOUT&DPXports

DLIN/ULOUT&DPXPortsarelocatedatthebackofBCUandconnectdirectlytoaBTS.

3.1.6.2.2 DLOUT/ULIN

DLOUT/ULINPortsarelocatedonthebackofADX‐H‐BCUandconnectdirectlytotheADX‐H‐RFU.

3.1.6.3 CommunicationPort

ADX‐H‐NMSmonitorsandcontrolstheADX‐H‐BCUviathisport.DCPowerisprovidedfromADX‐H‐PSUtothe

ADX‐H‐BCUviathisport.

BAND COM



Figure3‐23CommunicationPort(BCU)



3.2 HPR

‐ TheHighpowerremoteunitiscomposedofa(1)MainHPRandupto(1)ExtendedHPR.

‐ MainHPRandExtendedHPRusesameenclosure.



Figure3‐24ADX‐HPRSingleenclosure(bottomview)



3.2.1 Port

3.2.1.1 RFPort

3.2.1.1.1 Antennaserverport(DINtype)

메모 [C19]: 수정(CK)



AdvancedRFTechnologies,Inc.  37



BAN D 1 SER VER BAN D2 SER VER

AC IN 110V

A = AC _L

B = A C _N

C = F. G

OPTIC

GUI

EX _F1 _IN

EX_F1_O U T BAN D 3 SER VER BAN D 4 SER VER

CPL

(-30dB)

CPL

( -30dB)

CPL

(- 30dB )

CPL

(-30dB)

CPL

( -30dB)

CPL

(-30dB)

BAN D 6 SER VERBAN D5 SER VER

PO WER

RUN

EX_F2_IN EX _F2_O U T



3.2.1.1.2 ExtensionFilterport(Ntype)

‐ EX_F1_IN,EX_F1_OUT:extensionofadditionalFilterPort

‐ EX_F2_IN,EX_F2_OUT:extensionofadditionalFilterPort



3.2.1.2 Opticport



Figure3‐25InnerOpticportconnection



AdvancedRFTechnologies,Inc.  38



OPTIC



Figure3‐26Opticconnection



3.2.1.3 GUI,RS485port

‐ GUI_A,RS485_Aisforadditionalband(SISO,MIMO_1)

‐ GUI_B,RS485_Bisforadditionalband(MIMO_2)

‐ GUIconnectivityisalongwithopticlineposition(Seethepicturesbelowofvariouscombinations)



BAN D1 SER VER BAN D 2 SER VER

AC IN 110V

A = AC_L

B = AC_ N

C = F .G

OPTIC

GUI

EX _F_ IN

EX _F_OU T BAN D3 SER VER BAN D 4 SER VER

CPL

(- 30dB )

CPL

(-30dB)

CPL

(-30dB)

CPL

(-30dB)

CPL

(-30dB)

CPL

(-30dB)

BAND6 SERVERBAN D 5 SER VER

PO WER

RUN

OPTIC LINE

Usable GUI PORT (SISO/MIMO_1)

Usable GUI PORT (MIMO_2)



Figure3‐27ADX‐HPR6bandsGUIconnection(Singleenclosure)



3.2.2 LEDs

HPRhasthefollowingLEDsonthefrontpanelasshowninFigure3‐28.



AdvancedRFTechnologies,Inc.  39



Figure3‐28HPRLED



Table3‐6MasterHPRLEDSpecifications

ADXDAS‐ModuleSpecifications

PowerSolidGreenModulepowerisON

OFF ModulepowerisOFF



3.2.3 ACOn/OffSwitch,ACPort



Figure3‐29HPRACPort



Figure3‐29HPRACSwitch



TheACPoweron/offswitchislocatedonPSUintheenclosureofeachADX‐HPR.



AdvancedRFTechnologies,Inc.  40



TheADX‐HPRisoperatedattheonly110VAC.

Thesocket‐outletshallbeinstalledneartheequipmentandshallbeeasilyaccessible

(WARNING:TheACswitchmustbesettoOFFbeforecableconnectiontoavoidequipmentdamageand

personalinjury.)

(WARNING:Toavoiddamage,besure110VACforoperationofADX‐HPR.)

(CAUTION:DOUBLEPOLE/NEUTRALFUSING.)



TheprocedureforconnectingHPR

 ACS/WOFF

 ACcableconnection

 Opticconnection

 RFcableconnection

 RS485connection

 ACS/WON

3.2.4 DCOn/OffSwitch,DCPort



Figure3‐30HPRDCPort



Figure3‐31HPRDCSwitch



TheDCPoweron/offswitchislocatedonPSUintheenclosureofeachADX‐HPR.

TheADX‐HPRisoperatedattheonly‐48VDC.

Thesocket‐outletshallbeinstalledneartheequipmentandshallbeeasilyaccessible

메모 [C20]: DC고려사항추가



AdvancedRFTechnologies,Inc.  41



(WARNING:TheDCswitchmustbesettoOFFbeforecableconnectiontoavoidequipmentdamageand

personalinjury.)

(WARNING:Toavoiddamage,besure‐48V(‐36~‐76V)DCforoperationofADX‐HPR.

(CAUTION:DOUBLEPOLE/NEUTRALFUSING.)



TheprocedureforconnectingHPR

 DCS/WOFF

 DCcableconnection

 Opticconnection

 RFcableconnection

 RS485connection

 DCS/WON



4. CABLECONNECTION

4.1 HeadEndConnectionDiagrams

4.1.1 Front/RearHeadEndConnectionViewwithOptionalBCUunit

ADX- H-NM S

OWE

FT FAIL-H

FT FAIL-R

ARD

IL-H

RD F AIL-R

LINK F AIL -H

LIN K

IL-R

HOST HE VI EW

REMOTE RU V IEW

ADX- H-PSU

OWE

CHG S

LOW

ATT

C FAIL

DC F AIL

DL OUTUL IN

HARD FAIL

DL S IG LOW

S O FT FA IL

POWER

ADX-H -RF U-P

DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA IL

POWER

ADX-H -RFU-7

DL OUTUL IN

HARD FA IL

DL SIG LOW

S O FT FA IL

POWER

ADX-H -RFU-C

DL OUTUL IN

HARD FAIL

DL SIG LOW

S O FT FA IL

POWER

ADX -H- RFU-A

ADX- H-CHC

UL1UL2UL3UL4

DL1DL2DL3DL4

UL5 UL6 UL7 UL8

DL5 DL6 DL7 DL8

LD FA IL5 -8 LI N K5 LI N K6 LI N K7 LI N K8LD FA IL1 -4 LI N K1 LI N K 2 LI N K3 LI N K4POWER

ADX- H-OPT

S O FT FA ILPOWER

ADX- H-BCU -P



AdvancedRFTechnologies,Inc.  42



Figure4‐1HECableconnection(1ADX‐RACK‐ODU+1BCU)



4.1.2 RearHeadEndConnectionViewwith(4)ADX‐RACK‐ODUunits



AdvancedRFTechnologies,Inc.  43



Figure4‐2HECableconnection(4ADX‐RACK‐ODUs)



4.2 HighPowerRemoteUnitConnectionDiagrams

‐ EthernetcableforRS485iscrossovertype



BAN D1 SER VER BAN D 2 SER VER

AC IN 110V

A = AC_L

B = AC_N

C = F.G

OPTIC

GUI

EX _F_IN

EX _ F_O U T BAN D3 SER VER BAN D 4 SER VER

CPL

(- 30dB )

CPL

(-30dB)

CPL

(-30 dB)

CPL

(-30dB)

CPL

(-30dB)

CPL

(-30dB)

BAN D 6 SER VERBAN D 5 SER VER

PO WER

RUN

OPTIC LINE

Usable GUI PORT (SISO/MIMO_1)

Usable GUI PORT (MIMO_2)



Figure4‐3ADX‐HPR6bandsconnection(Singleenclosure)



 WARNING!TheRS‐485portsshouldNEVERbeconnectedtotheEnthernetportoflaptoporEthernet

NetworkEquipment.DoingsomaycauseseriousdamagetotheRemoteModulesornetworkequipments.



메모 [C21]: 수정(CK)



AdvancedRFTechnologies,Inc.  44



5. MOUNTINGMETHOD

5.1 HeadEnd

5.1.1 RackMount



Figure5‐1HERackMount(Front&Rearview)

 Expandableupto4ADX‐RACK‐ODUs,4BCUsand2AUXCHs



POWER

SOFT FAIL-H

SOFT FAIL-R

HARD FAIL-H

HARD FAIL-R

LINK FAIL-H

LINK FAIL-R

POWER

CHG STS

LOW BATT

AC FAIL

DC FAIL



AdvancedRFTechnologies,Inc.  45



5.1.2 WallMount



Figure5‐2HEWallMount(TopView)

 Expandableupto3units(ODU,BCU)ormax3U(132mm)

‐ ODUorBCUwillbestackedupabovebasic19”HEchassiswhichincludesNMS,RFU,PSUand

CHC



POWER

SOFT FAIL-H

SOFT FAIL-R

HARD FA IL-H

HARD FAIL-R

LINK FAIL-H

LINK FAIL-R

POWER

CHG STS

LOW BATT

AC FAIL

DC FAIL



AdvancedRFTechnologies,Inc.  46



5.2 HPR

5.2.1 WallMount

ADX‐HPRissupportonlywallmount.



Figure5‐3HPRWallMount



6. INSTALLATION

6.1 Pre‐InstallationInspection

PleasefollowtheseproceduresbeforeinstallingADXHPRequipment:

o Verifythenumberofpackagesreceivedagainstthepackinglist.

o Checkallpackagesforexternaldamage;reportanyexternaldamagetotheshippingcarrier.If

thereisdamage,ashippingagentshouldbepresentbeforeyouunpackandinspectthecontents

becausedamagecausedduringtransitistheresponsibilityoftheshippingagent.

o Openandcheckeachpackageagainstthepackinglist.Ifanyitemsaremissing,contactADRF

customerservice.

o Ifdamageisdiscoveredatthetimeofinstallation,contacttheshippingagent.

o VerifytheACvoltagewithDVM(Voltmeter)is110VAC.IncorrectACvoltagecandamagethe

ADXequipment.

o Thispowerofthissystemshallbesuppliedthroughwiringinstalledinanormalbuilding.If

powereddirectlyfromthemainsdistributionsystem,itshallbeusedadditionalprotection,such

asovervoltageprotectiondevice.

o Overvoltagecategory(OVC)&Pollutiondegree(PD)

Overvoltagecategory(OVC)OVCII

Pollutiondegree(PD)PD2



AdvancedRFTechnologies,Inc.  47



6.2 ADXDASInstallationProcedure

6.2.1 HEInstallationProcedure

CAUTION: ADXDASHEshouldbeinstalledinsidebuildingonly.



6.2.1.1 InstallingaADXDASHEinarack

TheADXHEchassismountsinastandard19”(483mm)equipmentrack.Allowclearanceof3”(76mm)atthe

frontandrear,and2”(51mm)onbothsidesforaircirculation.Notoporbottomclearanceisrequired.



 Consideration:

‐ Eightmountingholesarelocatedon4cornersofADXHEtoattachittothe19”rack.TheADXHE

mustbesecurelyattachedtoarackthatcansupporttheweightoftheADX.

 Mountprocedure

‐ ThefollowingstepsshouldbefollowedwhilemountingtheADXHE

 DetachthewallmountbracketassembledlocatedatthebaseoftheADX‐HEchassis

 VerifythattheHEandMountingholesareingoodcondition

 SettheADXDASHEagainstthe19”rackandsecuretheunitwithscrews

 VerifythatADXHEissecurelyattached

 ConnecttheGNDcable

 ConnecttheRFcable

 ConnectthePower

 ConnecttheOpticcable



AdvancedRFTechnologies,Inc.  48



Figure6‐1ADXHE19”RackMountInstructions







AdvancedRFTechnologies,Inc.  49



6.2.1.2 WallmountingtheADXDASHE

IftheADXHEchassisisbeingmountedtoawall,thenallowclearanceofatleast17”(430mm)onthetop

(frontsideofHE)and2”(51mm)onthebottom(rearsideofHE)and2”(51mm)onbothsidesandfrontforair

circulation.



 Mountprocedure

‐ ThefollowingstepsshouldbefollowedwhenwallmountingtheADXHE

 VerifythattheHEandMountingholeareingoodcondition

 PlacetheADXHEagainstthewallandmarkofthemountingholes

 Drillholes(4holes,18Φmm,50mmdepth)intheinstallationsurfaceandinserttheanchorbolts

 BolttheADXHEtothewall

 MakesuretheADXHEissecurelyattached

 ConnecttheGNDcable

 ConnecttheRFcable

 ConnectthePower

 ConnecttheOpticcable



Figure6‐2ADXHEWallMountInstructions



AdvancedRFTechnologies,Inc.  50



6.2.1.2.1 InstallingaddedracktypemodulesintobasicHEchassis

AdditionalmodulessuchastheADX‐RACK‐ODUandADX‐H‐BCUcanbemountedtotheChassis(ADX‐H‐CHA)

usingtheincludedmountingbracketsthatcomewiththeadd‐onmodules.

 Amaximumofupto3addonmodules(ODU,BCU)canbemountedtothechassis

‐ ODUorBCUwillbestackedupabovebasic19”HEchassiswhichincludesNMS,RFU,PSUand

CHC



Figure6‐3WallMountInstructionsforADX‐HEadded1UUnit





AdvancedRFTechnologies,Inc.  51



6.2.2 RUInstallationProcedure

WallmountingtheADXHPR

 Mountprocedure

‐ ThefollowingstepsshouldbefollowedwhilemountingtheRemoteModule



 VerifythattheHPRandMountingholeareingoodcondition

 SeparatethewallmountbracketfromtheHPR

 Placedthewallmountbracketagainstthewallandmarkoffthemountingholes

 Drillholes(4holes,18Φmm)intheinstallationsurfacetheninserttheenclosedanchorbolts

 Boltthemountingbrackettothewall

 InstalltheHPRtothemountingbracket

 FastentheHPRtothemountingbracketusingtheincludedscrews

 VerifythattheHPRissecurelyattached

 ConnecttheAntennacable

 ConnectthePower

 ConnecttheOpticcable(ifapplicable)



AdvancedRFTechnologies,Inc.  52



Figure6‐4HPRWallMountInstructions





AdvancedRFTechnologies,Inc.  53



6.3 Grounding

Agroundcableisincludedinthebox.ThegroundingterminalsarelocatedattherearoftheADXHEandRU.

Thegroundingcableshouldbeproperlyconnectedbeforepoweringontheequipment.



Figure6‐5GroundCableConnection(HErearside)



Figure6‐6GroundCableConnection(HPRdualside)



Roundterminalslocatedonthesideofa1.25mm²(16AWG)ormorewiresUsingpermanentlyconnectedto

earth.







AdvancedRFTechnologies,Inc.  54



6.4 OpticPortCleaning

 Werecommendcleaningopticconnectorusingadryopticalcleaningswabortissueinadryenvironmentas

needed.Werecommendcleaningtheopticconnectorsonlyiftheexpectedopticlossishigherthantheloss

reportedintheWeb‐GUIby1.5dBo.(Figure6‐7)

 Whenopticconnectorarenotinuse,theportshouldbecoveredwithaprotectivedustcap.(Figure6‐8)



Figure6‐7OpticConnectorCleaning(left)andOpticPortCleaning(right)



Figure6‐8SC/APCOpticConnectorDustCap





AdvancedRFTechnologies,Inc.  55



7. COMMISSIONING

Thecommissioningprocessiscomposedofthefollowing:

‐ Pre‐CommissioningCheck(refertosection7.1)

‐ OpticCommissioning(Opticlosscompensation)(refertosection7.2.1)

‐ HEcommissioning(refertosection7.2.2)

‐ RUcommissioning(refertosection0)

‐ Commissioningverification(refertosection0)



7.1 Pre‐CommissioningCheck

7.1.1 Verifycableconnections

 Beforepoweringupunits,checkallRFcables,fibercables,andpowercablesconnections.

 AllpowerLEDsshouldbelit1minuteafterthecomponentshavebeenturnedon.

 CheckwhetherLD&PDLEDsofHEODUmodulesaresolidGREEN.(PDLEDwillbelitgreenwhenconnectedto

aMasterRU).

‐ IfthePDLEDforthelinkwithaconnectionwithtoaHPRisOFF,thenchecktheopticcable

connection.

‐ IftheopticcableisgoodandthePDLEDisnotlitgreen,thetryanotheropticportontheADX‐

RACK‐ODUtoseeiftheotherportlightsupgreen.

7.1.2 ConnecttotheWeb‐GUI

 ConfirmthattheNMSHost/RemoteswitchissettotheHostposition

 ConfirmthattheHEView/RUViewswitchissettotheHEViewposition

 ConnecttheRJ‐45crossovercablefromtheEthernetportofNMStotheEthernetportoflaptop

 LaunchastandardInternetbrowserlikeIEorGoogleChromeandtypetheSystemController’sIPaddress

(192.168.63.1)intotheaddessbar

 Ontheloginscreenusethefollowingdefaultlogin/passwordtogainaccess:

‐ Username:adrf

‐ Password:adrf



Figure7‐1Loginwindow





AdvancedRFTechnologies,Inc.  56



7.1.3 CheckNavigationTreeStatus

 CheckwhetherthestatusofnavigationtreeisLockorUnlock.

 Thenavigationtreeshouldbeinthe“Unlock”stateinwhenaddingorremovingactiveADXcomponents.



Figure7‐2NavigationtreeLock/Unlock



Whenthesystemislocked:

 Unabletodetectanyhardwarethatisadded

 Abletodetectanylinkfails(communicationerrorsbetweenNMSandcomponents)

 Systemshouldbelockedafterfinalcommissioning

Whenthesystemisunlocked:

 UnabletoperformBCU,RFU,orHPRcommissioning

 Systemiscontinuallyscanningfornewhardware

7.1.4 SetLocationInfo,InstallerInfoandDate&Time

 GototheInstallpageofNMS

 EnterLocation&installerinformation

 SetcurrentDate&Time

7.1.5 VerifyNavigationTreeLinks

 CheckwhetherallunitsconnectedtoHE&HPRarebeingdisplayedinthenavigationtree.

‐ NavigationtreeislocatedontheleftsideofWeb‐GUI(Figure7‐3)



Figure7‐3Navigationtree

 Checkwhetherlinkfailsexist.LinkfailsstatuscanbeseenonthefrontpanelofNMSmoduleviatheLinkFail‐

HandLinkFail‐RLEDlights.

‐ IfLINK‐Hfailexists,powercycletheHEPSUandcheckifLINK‐Hfailisstillpresentandrepeatthis

stepupto3timesoruntilthealarmclears.IfLINK‐Hfailstillexistsafter3powercycles,then

contactADRFTechnicalsupport.

‐ IfLINK‐Rfailexists,powercycletheADX‐H‐ODUmodulewhichisconnectedtotheMasterHPR

withlinkfailandchecktoseeiftheLINK‐Rfailisstillpresentandrepeatthisstepupto3timesor

untilthealarmclears.IfLINK‐Rfailstillexistsafter3powercycles,contactADRFTechnical

support.





AdvancedRFTechnologies,Inc.  57



7.1.6 BOMComparison&CheckBandConfiguration

 BOMcomparison

‐ OntheSysteminformationpageintheSystemmenu,thelistofallcomponentsconnectedtothe

ADX‐H‐NMSshouldmatchtheADXNavigationtree.ThislistcanbeusedtoverifyBOMgenerated

bydesignerorinstallerforallactivecomponents.Pleasenotethatpassivecomponentssuchas

theADX‐H‐CHC,ADX‐R‐CHC,ADX‐H‐PSU,andtheADX‐R‐4WSwillnotshowuponthisreport.

 CheckBandConfiguration

‐ CheckwhetherthebandconfigurationofADX‐H‐RFUisidenticaltothebandconfigurationofthe

ADXHPRunits.AnydiscrepancieswillappearintheSystemInformationreport.

‐ Checktoseeiftherearemultipleremotemoduleswiththesamefrequencybandswithin1

remoteunit.ThisinformationisdisplayedontheSystemInformationpageintheSystemmenu

asnotificationmessage.

7.1.7 Lockcurrentnavigationtree

 IftherearenoerrorsintheprocessofBOMComparison&CheckBandConfiguration,thenlocktheNavigation

Treebyclikingonthe“LockSystem”button.

‐ AfterlockingtheNavigationTree,linkfailalarmsshouldnotappear.Iflinkfailalarmsare

present,pleasecheckthephysicalconnectionofthedevicewiththelinkfailalarm.

‐ Thesystemmustfirstbeplacedinthe“Unlock”statebeforeaddinganynewdevices.Newly

addeddeviceswillappearintheNavigationTreewhenthepageisrefreshed.Onceallnew

hardwarehasbeenaddedtotheNavigationTree,thetreemustbelockedbeforecommissioning

thesystem.





AdvancedRFTechnologies,Inc.  58



7.2 Commissioning

7.2.1 OpticCommissioning



Figure7‐4ODUInstallpage

 NavigatetotheInstallpageofADX‐H‐ODU(Figure7‐4)

 Comparethevaluesofmeasuredopticloss(LDpower–PDpower)intheWeb‐GUIwiththeactualopticloss

whichistypicallymeasuredatthetimeofinstallationofthefiber.

‐ ThecalculatedopticlossisdisplayedwhenthemousepointerisplacedovertheStatusindicator

ofeachlink



Figure7‐5measuredopticlossdisplay



‐ Ifthedifferencebetweenthemeasureopticlossandthecalculatedlossislargerthan1.5dBo,

thencleantheopticconnectorandopticportusingopticalcleaningswab.(refertosection6.4)

 ThefollowingisthedefinitonoftheStatusindicatorofeachlink:

‐ Green:Indicatesthatopticlossislessthan5dBo

‐ Orange:Indicatesthatopticlossisgreaterthan5dBo

‐ Gray:NoMasterHPRisconnectedtothislink.

 ThefollowingisthedefinitionforthebackgroundcoloroftheCommissioningbutton:

‐ Green:Indicatesthatnoopticlosscompensationisneeded.

‐ Orange:Indicatesthatopticlosscompensationisneeded.

‐ Gray:NoMasterHPRisconnectedtothislink.

7.2.1.1 Howtocompensatetheopticloss



AdvancedRFTechnologies,Inc.  59



Opticlosscompensationshouldbeperformedwhenthecolorof“Commissioning”buttonisorange.The

“Commissioning”buttonwillturnorangewhenthedifferencebetweenthecompensatedattenuationandthe

actualcompensatedattenuationlevelisgreaterthan1.5dB.Opticcompensationcanbeperformedbyclickingthe

orange“Commissioning”button.

 Theopticlosscompensationforuplinkanddownlinkareperformedseparately.

‐ TheopticlosscompensationfordownlinkwillbeperformedbasedontheLDleveloftheODU

andthePDleveloftheMasterRU.

‐ TheopticlosscompensationforuplinkwillbeperformedbasedontheLDleveloftheMaster

HPRandthePDleveloftheODU.

 OpticlosscompensationadjuststheattenuationbasedonTable7‐1andthecalculatedopticloss(LDlevel‐PD

Level).

‐ Thecalculatedopticlossisdisplayedwhenamouseisplacedonthecircleofeachlink.(Referto

section7.2.1.1)

‐ Basedonthetablebelow,whenthecalculatedopticlossis1dB,theattenuationwillbesetto

11dB.

‐ TheattenuatorfordownlinkopticlosscompensationislocatedattheMasterRU.

‐ TheattenuatorsforuplinkopticlosscompensationarelocatedattheODU.

Table7‐1Opticlosscompensationtable

OpticLoss(dBo)CompensatedAttenuation(dB)

013

0.5 12

111

29

37

45

53



 Example:Let’ssaythatthisADX‐H‐ODUhadpreviouslybeencommissionedinasystemwheretheopticloss

was3dBo.Intheprevioussystem,thecorrectamountofattenuationis7dB.TheADX‐H‐ODUwasmovedto

anothersiteandthenewsystemhasanopticlossofonly1dBo.At1dBoofloss,thecorrectamountof

attenuationshouldbe11dB.Whenthissystempowerson,opticcommissioningwillneedtobeperformed

becausethedifferencebetweentheoldattenuationlevelandthenewattenuationlevelis4dBwhichexceeds

the1.5dBthreshold.Onceopticcommissioningisperformed,itwillsettheattenautionlevelto11dB.





AdvancedRFTechnologies,Inc.  60



7.2.2 HECommissioning

HEcommissioningiscomposedofHEBCUandHERFUcommissioning.TheHEBCUisanoptionalcomponent

andshouldbeusedwhenWPSs’signalsarebeingusedinthesamefrequencyband.

7.2.2.1 Compositepower

ToperformHEcommissioning,theusershouldcalculatedownlinkcompositeinputlevelandaddtheproper

amountofbreathroomrequiredforriseintraffic.

 Informationthatisneededtocalculatecommissioninglevelsare:

‐ Servicefrequencyband

‐ Servicetechnology

‐ Thenumberofwirelessserviceprovider

‐ Thenumberofcarrierspertechnology

‐ Thenumberofbandsharingsameamplifier

7.2.2.1.1 DLCompositeInputLevelCalculationsforHECommissioning

7.2.2.1.1.1 SingleWSPinafrequencyband

 MeasuretheoutputpoweroftheBTSsignalthatwillbeinsertedintotheRFUusingaSpectrumAnalyzer.

‐ Ifinputsignalincludesmorethanonetechnology,thenmeasurethecompositepowerofeach

technology.

 BasedonTable7‐2,calculatethemaximumcompositeinputlevelbyusingthefollowingformula:

o “OutputpowerofBTSoftechnologybeingused”+“back‐offvalue”(refertoTable7‐2)

‐ IfcalculatedcompositeHEDLinputpowerexceedsthepermittedmaximuminputrange,then

additionalattenuationwillneedtobeaddedsothatthecalculatedHEDLinputpowerdoesnot

exceed25dBm.

Table7‐2Back‐offvalueforeachtechnologyduetotrafficbreathing

TechnologyConnectedtoBTS

CDMA6~8dB

1xEVDO6~8dB

WCDMA8~10dB

HSPA8~10dB

iDEN0~3dB

GSM0~3dB

LTE8~10dB

7.2.2.1.1.2 MultipleWSPsinafrequencyband

WhenmultipleWSPsexistinafrequencybandatthesametime,theADX‐H‐BCUcanbeusedto

combine/dividethesignalsreceivedfrommultipleWSPs.

‐ TheADX‐H‐BCUcanreceiveupto3incomingDLsignals.Eachincomingsignalcanbeattenuated

individuallyallowingtheusertospecifypowerratiostocontrolthepowerpercarrier.

‐ ThedownlinkpathofBCUhastheinputrangefrom0to25dBm.

‐ IfthedownlinkoutputofBCUexceedsDLoutputALClevelsetbyuser,ALCfunctionwillactivate

andlimittheDLoutputfromexceedingthedefinedALClevel.

‐ TheDLoutputofADX‐H‐BCUistransferredtotheDLinputofRFU.

 MeasuretheoutputpoweroftheBTSsignalthatwillbeinsertedintotheBCUusingaSpectrumAnalyzer.

‐ Ifinputsignalincludesmorethanonetechnology,thenmeasurethecompositepowerofeach

technology.

 BasedonTable7‐2,calculatethemaximumcompositeinputlevelbyusingthefollowingformula:

o “OutputpowerofBTSoftechnologybeingused”+“back‐offvalue”(refertoTable7‐2)



AdvancedRFTechnologies,Inc.  61



‐ IfcalculatedcompositeHEDLinputpowerexceedsthepermittedmaximuminputrange,then

additionalattenuationwillneedtobeaddedtotheBCUinputportsothatthecalculatedHEDL

inputpowerdoesnotexceed25dBm.

 TheRFUDLinputcommissionlevelisthecombinedDLOutputALCLeveloftheADX‐H‐BCUwhichcanbe

obtainedfromtheControlpageoftheADX‐H‐BCU.

‐ ThemaximuminputlevelofHERFUwillnotexceed10dBm(=5dBm+10*log10(3))becausethe

maximumoutputofBCUeachpathislimitedto5dBmbytheALCfunction.

7.2.2.1.2 Exampleofcommissioningvaluecalculation

7.2.2.1.2.1 AT&TsignalinthePCSbandwithmultipletechnologies(withoutattenuation)

Table7‐3shows2technologiesbeingusedbyAT&TwithinthesamebandwhichareinputtedintotheHERFU.

Table7‐3Inputsignalconditions@HERFUdownlinkinput

WSPAT&T

TechnologyGSMWCDMA

Totalinputperband20.0dBm20.0dBm

HETotalInput23.0dBm

 Thedownlinkinputlevelforeachtechnologyshouldbemeasuredbecausetwotechnologies(GSM&WCDMA)

arebeingusedbyAT&TinthePCSband.

‐ TotalmeasuredinputpowerforGSMis20dBmandforWCDMis20dBm.

 TheHEDLmaximuminputlevelforeachtechnologycanbecalculatedbyaddingtheback‐offvalueper

technologyduetotrafficloadchange(breathing).

 EstimatedTotalMaxInputperband=Totalinputperband+back‐offvalueperbandforbreathing.

 HEDLmaximuminputlevelbecomesthesumofHEDLmaximuminputlevelforeachtechnology.

‐ ThesumofHEDLmaximuminputlevelforeachtechnologyis28dBm(25.0dBmforGSM+

25.0dBmforWCDMA=28.0dBm)andthisvalueis3dB(28dBm–25dBm)largerthanthe

maximumDLinputofHERFU.

‐ IfthecalculatedHEdownlinkcommissioningvalueexceedsthemaximumDLinputofHERFU,

attenuationwillneedtobeaddedhavethecalculatedHEdownlinkcommissioninglevelnot

exceed25dBm.

Table7‐4HEmaximumdownlinkinputlevelwithout10dBattenuator

WSPAT&T

Totalinputperband20.0dBm20.0dBm

Backoffperbandforbreathing5.0dB5.0dB

EstimatedTotalMaxInputperband25.0dBm25.0dBm

EstimatedTotalMaxInput28.0dBm

AvailableMaxInput25.0dBm



7.2.2.1.2.2 AT&TsignalsinthePCSbandwithmultipletechnologies(with10dBofattenuation)

Afteradding10dBofattenuationtothesystem,theinputlevelsperbandandHETotalInputcanbeseen

below:

Table7‐5HEdownlinkinputsignalconditionsafteradding10dBattenuatortoHEdownlinkinputport

WSPAT&T

TechnologyGSMWCDMA



AdvancedRFTechnologies,Inc.  62



Totalinputperband10.0dBm10.0dBm

HETotalInput13.0dBm

TheRFUcannowbecommissionedwiththe10dBofattenuationbyusingaDLinputcommissionlevelof

18dBm.

Table7‐6HEmaximumdownlinkinputlevelafteradding10dBattenuatortoHEdownlinkinputport

WSPAT&T

Totalinputperband10.0dBm10.0dBm

Backoffperbandforbreathing5.0dB5.0dB

EstimatedTotalMaxInputperband15.0dBm15.0dBm

EstimatedTotalMaxInput18.0dBm

AvailableMaxInput25.0dBm

7.2.2.1.2.3 MultipleWSPs’signalsexistinthePCSband(withpowerratio)

Table7‐7displaysallthevariousincomingDLsignalsthatareenteringintotheHEPCSBCU.TheADX‐H‐BCU

hastotal3inputportsandintheexamplebeloweachporthasbeenassignedtoSprint,AT&T,andVzW.

Table7‐7Inputsignalconditions@HEBCUdownlinkinput

WSPSprint‐CH1AT&T‐CH2VzW‐CH3

TechnologyCDMAGSMWCDMACDMA

Totalinputperband5.0dBm10.0dBm10.0dBm7.0dBm

BCUTotalInput14.5dBm

 CalculatemaximumDLinputlevelforeachWSPfactoringintheback‐offvalues.

Table7‐8HEmaximumdownlinkinputlevel

WSPSprint‐CH1AT&T‐CH2VZW‐CH3

Totalinputpercarrier5.0dBm10.0dBm10.0dBm7.0dBm

Backoffperbandforbreathing4.0dB5.0dB5.0dB4.0dB

EstimatedTotalMaxInputpercarrier9.0dBm

15.0dBm15.0dBm

11.0dBm

18.0dBm

 BasedonthecalculatedmaximumDLinputlevelforeachport,theusershoulddecideonatargetmaximum

InputpowerforeachBCUport.

‐ TargetedmaximumInputpowerforeachBCUportshouldnotbelessthanthecalculated

maximumDLinputlevelforeachportandshouldnotexceedthemaximuminputlevel,25dBm.

Table7‐9Targetedmaximuminputpower

WSPSprint‐CH1AT&T‐CH2VZW‐CH3

Targetedmaximuminputpower

9.0dBm18.0dBm11.0dBm

19.2dBm

TargetedDLOutputPowerRatiosetbyuser30.0%20.0%50.0%

 CalculatetheDLmaximumoutputpowerofBCUbasedontargetedmaximumInputpowerforeachBCUport.

‐ ThehighestpowerratiothathasbeensetisVZW‐ CH3@50%.TheADX‐H‐BCUwillapply

attenuationtothisporttosetthemaximumoutputpowerto5dBm,therefore6dBof

attenuationwillbeappliedtothisport.



AdvancedRFTechnologies,Inc.  63



‐ TheattenuationandDLoutputALClevelfortheotherportsaresetbasedontheformulabelow

tokeepthepowerratiobetweenBCUports.

 Themaximumoutputpowerforthespecifiedpath=10*log10[10^(Max_ALC/10)x(Pwr_Ratio)/

Max_Ratio]

 Max_ALC:DLoutputALClevelforthepathwithmaximumpowerratio=5dBm

 Pwr_Ratio:TargetedDLoutputpowerratiovalueforthespecifiedpath

 Max_Ratio:maximumpowerratiovalue

 Theattenuationforthespecifiedpath=Thetargetedmaximuminputpowerforthespecifiedpath‐

Themaximumoutputpowerforthespecifiedpath

 DLoutputALClevel=Thetargetedmaximuminputpowerforthespecifiedpath‐Theattenuation

forthespecifiedpath

 ThepathforAT&T‐CH2

 Themaximumoutputpower=10*log10[10^(5/10)x20%/50%]=1.02dBm

 TheATTvalue=18.0dBm‐1.02dBm=16.98dB16.5dB(thecontrolstepofusedattenuatoris

0.5dB)

 DLoutputALClevel=18dBm–16.5dB=1.5dBm

 ThepathforSprint‐CH1

 Themaximumoutputpower=10*log10[10^(5/10)x30%/50%]=2.78dBm

 TheATTvalue=9.0dBm‐2.78dBm=6.22dB6.0dB(thecontrolstepofusedattenuatoris0.5dB)

 DLoutputALClevel=9.0dBm–6.0dB=3.0dBm

‐ TheDLmaximumoutputpowerofBCUisthesumofmaximumoutputpowerforeachportand

thispowerbecomestheHERFUinputcommissioninglevel.

‐ ThemaximuminputlevelofHERFUshouldbelessthan10dBm(=5dBm+10*log10(3))because

themaximumoutputofBCUpereachpathdoesn’texceed5dBmbyALCfunction.

Table7‐10MaximumOutputPowerpercarrier

WSPSprintAT&TVZW

Targetedmaximuminputpower

9.0dBm18.0dBm11.0dBm

19.2dBm

TargetedDLOutputPowerRatiosetbyuser30.0%20.0%50.0%

DLmaximumoutputpower

(ATTcontrolstep,0.5dBisnotconsidered)2.78dBm1.02dBm5.0dBm

ATTvalue6.0dB16.5dB6.0dB

DLoutputALClevelor

DLMaximumoutputpower

(ATTcontrolstep,0.5dBisconsidered)

3.0dBm1.5dBm5.0dBm

8.2dBm(RFUDLInputcommissioninglevel)

DLOutputPowerRatio

consideringATTcontrolstep0.5dB30.37%21.50%48.13%





AdvancedRFTechnologies,Inc.  64



7.2.2.1.3 HEBCUCommissioning

WhenperformingBCUcommissioning,theuserwillneedtoentertheDLinputcommissioningleveland

TargetedDLOutputPowerRatioforeachRFpath.Refertosection7.2.2.1tocalculateDLinputcommissioning

level.Ifaportisnotbeingused,theDLInputCommissioningLevelshouldbesetto“disabled”.

7.2.2.1.3.1 HEBCUCommissioningProcedure

 GotoInstallpageoftheBCUontheWeb‐GUI



Figure7‐6BCUInstallWindow

 SelectaDLInputCommissioningLevelforeachRFpath

‐ DLInputCommissioningLevelsrangeis0~+25dBm(0.5dBstep)

 EnterHEBCUdownlinkoutputpowerratioforeachport

 Pressthe“Apply”button

 TheattenuationvalueandoutputALClevelforeachDL/ULpathwillbesetautomaticallybasedontheHEBCU

downlinkinputcommissioninglevelanddownlinkoutputpowerratioforeachport.

 TheBCUwillchecktoseeifALCisactiveonanyoftheports.

‐ Duringthecommissioningroutine,ifALCisactivated,apopupmessagewillappearstatingthat

ALCisrunning.Ifthisisthecase,thenthereisachancethatthe“back‐off”valueneedstobe

increasetoallowmorebreathingroom.

 TheBCUcheckstoseeiftheBCUhasanyalarms.

‐ Ifasoftfailispresent,thesystemwillprompttheuserwhetherornottheywouldliketo

continue.

‐ Ifhardfailispresent,thecommissioningprocesswillstopimmediately.





AdvancedRFTechnologies,Inc.  65



7.2.2.1.4 HERFUcommissioning

IfaBCUisbeingusedinthesystem,theBCUshouldbecommissionedbeforecommissioningtheHERFU.

ForRFUcommissioning,theuserwillneedtocalculatetheDLinputcommissioninglevel.Refertosection

7.2.2.1toforinformationtodeterminetheDLinputcommissioninglevel.

7.2.2.1.4.1 HERFUcommissioningProcedure

 GotoInstallpageofRFUontheWeb‐GUI



Figure7‐7RFUInstallWindow

 EnterHERFUdownlinkinputcommissioninglevel

‐ Inputrange:0~+25dBm,0.5dBstep

 Pressthe“Apply”button

 TheattenuationlevelswillbesetautomaticallybasedonDLInputCommissioningLevelthatisselected.

 CheckstoseeifDLinputislow.

‐ Duringthecommissioningroutine,ifDLinputlevelis10dBlessthancommissioninglevel,a

popupmessagewillappearstatingthatDLinputislow.Ifthisisthecase,thenthereisachance

thatthe“back‐off”valueneedstodecreasebreathingroom.

 CheckstoseeifALCisactive.

‐ Duringthecommissioningroutine,ifALCisactivated,apopupmessagewillappearstatingthat

ALCisrunning.Ifthisisthecase,thenthereisachancethatthe“back‐off”valueneedstobe

increasetoallowmorebreathingroom.

 CheckstoseeiftheRFUhasanyalarms.

‐ Ifasoftfailispresent,thesystemwillprompttheuserwhetherornottheywouldliketo

continue.

‐ Ifhardfailispresent,thecommissioningprocesswillstopimmediately.

 Commissioningissuccessfullycompleted.







AdvancedRFTechnologies,Inc.  66



7.2.3 HPRCommissioning

HPRcompositedownlinkoutputlevelcanbedeterminedusingsimulationtoolslikeiBwave.Usershould

simulatethisoutputlevelinordertoensurethatallserviceareashavesufficientcoverage.

 ThesimulatedcompositeDLoutputpowervalueshouldnotexceedthemaximumoutputleveloftheHPR,

whichis46/44.8/43dBm.

 ThesimulatedcompositeDLoutputpowervaluewouldbeusedasHPRDLcommissioningoutputlevel.DL

attenuationvaluewillbeadjustedautomaticallybasedonthissimulatedvalueHPRcommissioninglevel.



ForHPRcommissioning,usershouldenterinformationonDLoutputcommissioninglevel.Refertosection

7.2.2.1tocalculateDLoutputcommissioninglevel.

 GotoInstallpageofRemoteModuleonthewebGUI



Figure7‐8RemoteModuleInstallWindow

 EnterHPRdownlinkoutputcommissioninglevel

‐ Outputrange:5~+46/44.8/43dBm,0.5dBstep

 Pressthe“Apply”button

 TheattenuationlevelforeachDL/ULpathwillbesetautomaticallybasedonDLOutputCommissioningLevel

thatisentered

 CheckstoseeifDLoutputislow.

‐ Duringthecommissioningroutine,ifDLoutputlevelis10dBlessthancommissioninglevel,a

popupmessagewillappearstatingthatDLoutputislow.Ifthisisthecase,thenthereisachance

thatthe“back‐off”valueneedstodecreasebreathingroom.

 CheckstoseeifALCisisactive.

‐ Duringthecommissioningroutine,ifALCisactivated,apopupmessagewillappearstatingthat

ALCisrunning.Ifthisisthecase,thenthereisachancethatthe“back‐off”valueneedstobe

increasetoallowmorebreathingroom.

 CheckstoseeiftheSub‐RUhasanyalarms.

‐ Ifasoftfailispresent,thesystemwillprompttheuserwhetherornottheywouldliketo

continue.

‐ Ifhardfailispresent,thecommissioningprocesswillstopimmediately.

 Commissioningissuccessfullycompleted.





AdvancedRFTechnologies,Inc.  67



7.3 DASInstallVerification

7.3.1 SettingSNMP&RemoteIP

 GotoInstallpageofNMS(refertosection8.2.4.1.4)

 Whenexternalmodemboxisconnected,usershouldsetSNMP&RemoteIPinformation.

7.3.2 VerificationthroughWebbasedGUI

 GotoSysteminformationpageofSystem(refertosection8.2.5.4.1)

‐ CheckifRemoteModulewithsamefrequencybandexistmorethanonewithinoneHPR.

‐ CheckifthereareanynoncommissionedmodulesinHEorRU.

‐ Checkifanycriticalalarmsarepresent.

7.3.3 ULnoisepowerdetection

WhentheULnoiselevelsislargerthantheexpectedvalue,ADXDAShasafunctionthatwillmeasurethe

uplinknoiseforeachHPRandwillgeneratesareportwiththeULnoiselevels.Thiswillhelptheuserdetermine

whichHPRmightbethecauseoftheelevatedULnoise.

 ULnoisepowermeasurementcanbeperformedforonlyonefrequencybandatatime.

 Formoreinformation,refertosection8.2.3.3.3.





AdvancedRFTechnologies,Inc.  68



8. WEB‐GUI

8.1 Web‐GUISetup

TheWeb‐GUIallowstheusertocommunicatewiththeDASsystemeitherlocallyorremotely.Toconnectto

theDASsystemlocally,youwillneedalaptopwithanEthernetportandaRJ‐45crossovercable.Toconnectto

theDASsystemremotely,youwillneedtohaveanactiveinternetconnectionandtheADXsystemmusthaveand

externalmodemboxconnectedtotheADX.

8.1.1 DASsystem/PCConnectionUsingWeb‐GUI

 VerifythatyourLocalAreaConnectionissettoObtainanIPaddressautomaticallyundertheInternetProtocol

(TCP/IP)properties

‐ Ifyouareconnectingtotheunitremotely(useofamodem),thenskipthisandnextstep.

 ConnecttheRJ‐45crossovercablebetweenthelaptop’sEthernetportandtherepeater’sEthernetport

 LaunchanInternetBrowser

 TypethefollowingIPaddressintotheaddressbarofMicrosoftInternetExplorer:http://192.168.63.1

‐ Ifyouareconnectingtotheunitremotely,thentypetheIPaddressofthemodemtoconnectto

theunit

 Thefollowingloginscreenwillappear:



Figure8‐1Loginscreen



IfyouarenottheAdministrator,pleasetypeinyourassignedusername&passwordwhichyoushouldhave

receivedfromtheAdministrator.



Table8‐1AccountInformationforLogin

AccounttypeShowitemsControlItemsDefaultIDDefaultPassword

AdministratorallItems allitems admin admin

Userrestricteditemsrestricteditems adrf adrf

Guestrestricteditemsread‐only guest guest





AdvancedRFTechnologies,Inc.  69



8.2 Administrator/UserMode

8.2.1 Common

8.2.1.1 NavigationtreeLock/Unlock

Whenthesystemis“Locked”,agreenlockiconwillappearabovethenavigationtree.Whenthesystemis

locked,newdevicescannotbeadded.Anydevicesaddedtothesystemwhenthesystemis“Locked”willnotbe

detectedbytheNMS.Afterasystemhasbeencommissionedproperly,thesystemshouldbeleftinthe“Locked”

position.Tounlockthesystem,clickonthe“UnlockSystem”buttontotherightoftheicon.

Whenthesystemis“Unlocked”,anorangeiconwillappearabovethenavigationtree.Whenthesystemis

unlocked,newdevicesaddedtothesystemwillbeautomaticallydetected.Oncethenewhardwareappearsinthe

systemtree,thenthesystemcanbelocked.Tolockthesystem,clickonthe“LockSystem”buttontotherightof

theicon.



Figure8‐2NavigationtreeLock/Unlock

8.2.1.2 NavigationTree



Figure8‐3Navigationtree

ThenavigationtreelocatedonthelefthandsideoftheWeb‐GUIallowstheusertoswitchbetweenthe

variousmodulesthatareconnectedtothesystem.

Table8‐2Navigationtree

ParametersDescription

Expandstheentirenavigationtree

Collapsestheentirenavigationtree

Themodulehastheexpandablesubordinatemodules

Thebranchiscurrentlyexpanded

Themodulehassoftfailalarm

Themodulehashardfailalarm

Themodulehasnoalarms(normal)

Theselectedmodulewillhaveorangecoloredtext



AdvancedRFTechnologies,Inc.  70



8.2.1.3 PowerStatus

Displaythepowersourcethatiscurrentlybeingused.

Table8‐3PowerSupplyStatus

InputPowerStatusDisplayImage

AC

Battery

8.2.1.4 CommissioningStatus

Displaywhetherornotthemodulehassuccessfullybeencommissioned.

Table8‐4CommissioningICON

StatusDisplayImage

Commissioned

Not‐Commissioned

8.2.1.5 Information



Figure8‐4ADXDASGeneralInformation

 Information:Displaystheserialnumber,latitude/longitude,firmwareversionofselectedmodule,andWeb

GUIversionoftheNMS.

 Location:DisplaystheaddresswheretheADXDASisinstalled.

 Description:Displaysthedescriptionofselectedmodule.Thedescriptionofeachmodulecanbeeditedfrom

theInstalltab.Itisrecommendedtousethelocationofthemoduleasthedescription.Thisdescription

informationcanbeseenwhenhoveringoverthedevicetreeinordertoeasilyidentifyeachcomponent.

 TechnicalSupport:DisplaysADRF’sTechnicalSupportcontactinformation.

 InstallerContactInfo:Displaysthecontactinformationoftheinstaller.



AdvancedRFTechnologies,Inc.  71



8.2.2 StatusTab

8.2.2.1 Status–NMS



Figure8‐5Status‐NMS

TheNMSStatuspageprovidesanoverallviewofhowthesystemisperforming.FromtheNMSStatuspage,

theusercanseewhatmodulesareconnectedtoADXDAS.Inaddition,theusercanseeifanyalarmsarepresent

inthesystemandalsothecommissioningstatusofeachmodule.

8.2.2.1.1 SystemSummary



Figure8‐6SystemSummary

TheSummarysectionprovidestheuserwiththenumberofcomponentsphysicallyconnected,thenumberof

soft/hard/linkfailspresentinthesystem,andalsothenumberofcommissionedandnon‐commissioned

componnets.



AdvancedRFTechnologies,Inc.  72



Table8‐5SystemSummaryDescription

ParametersDescription

ConnectedDisplaythenumberofmodulesphysicallyconnectedtoADXDAS

SoftFailDisplaythenumberofsoftfailpresentoneachmodule

HardFailDisplaythenumberofhardfailpresentoneachmodule

LinkFailDisplaythenumberoflinkfailpresentoneachmodule

NotCommissionedDisplaythenumberofnon‐commissionedorcommissionfailedmodule

CommissionedDisplaythenumberofsuccessfullycommissionedmodule

8.2.2.1.2 HEView/HPRView,SystemScanTime

 HEView/RUView

‐ DisplayswhethertheNMSissettoHEvieworHPRview.

‐ Refertosection3.1.1.4

 SystemScanTime

‐ Displaysthetimeittakestoscanandupdatetheinformationofallthemodulesthatareonthe

navigationtree.Thistimewillincreaseasmorecomponentsareaddedtothesystem.

‐ WhenNavigationTreeisunlocked,theusershouldwaitatleastthe“SystemScanTime”forthe

systemtodetectnewlyaddedhardware.



Figure8‐7Systemscantime,HEview/RUview

8.2.2.1.3 HEAlarmStatus

DisplaythealarmstatusofeachHEcomponent.



Figure8‐8HEalarmstatus



AdvancedRFTechnologies,Inc.  73



8.2.2.1.4 HECommissioningStatus

DisplaycommissioningstatusofeachHEcomponent.



Figure8‐9HECommissioningstatus

Table8‐6DescriptionforHECommissioningstatus

StatusDisplayDescription

InstalledStatusPhysicallyInstalledTextisblack

PhysicallyNot‐InstalledTextisgray

CommissioningStatusSuccessGreen

FailedornotcommissionedGray

8.2.2.1.5 Alarm

DisplaysalarmstatusoftheNMS.Ifanalarmispresentinthesystem,thecolorofthesystemalarmtabwill

changeaccordingtothetypeoffailure.

Table8‐7DescriptionforNMSalarm

AlarmSeverityDescription

System



OverTemperatureHardFail/

SoftFail

TemperatureofNMSishigherthanthethreshold

levelforovertemperaturealarm

UnderTemperatureSoftFailTemperatureoftheNMSislowerthanthethreshold

levelforundertemperaturealarm

SystemHaltHardFailHEsystemhalt

PowerAlarm



ACFailSoftFailACpowerisoperatingoutsideofitsnormalrange

DCFailSoftFailDCpowerisoperatingoutsideofitsnormalrange

OverCurrentHardFailTotalcurrentofHEishigherthanthethresholdlevel

forovercurrentalarm

BatteryLowSoftFailVoltageofbatteryconnectedtoHEPSUislowerthan

thedefinedthreshold





AdvancedRFTechnologies,Inc.  74



8.2.2.2 Status–BCU



Figure8‐10Status–BCU



8.2.2.2.1 Band

DisplaysthebandwidthandthefrequencyrangesforDLandULoftheBCUmodule.



Figure8‐11Status–BCUBand

8.2.2.2.2 Power&Atten



Figure8‐12Status–BCUPower&Atten

 DLCommissioningLevel:DisplaysthecommissioninglevelforeachindividualRFpath.Ifunithasnot

beencommissioned,“NotCommissioned”willbedisplayed.



AdvancedRFTechnologies,Inc.  75



 DLInput:DisplaysthecurrentlyincomingsignalstrengthofeachRFpathalongwiththecompositeDL

inputpowerofall3RFpaths.

 Atten:Displaystheattenuationvaluesthatthesystemiscurrentlyusingwhichisdefinedbythe

powerratiosspecifiedbytheuser.

 DLOutput:DisplaystheoutputvalueforeachRFpathalongwiththecompositeDLoutputpowerof

all3RFpaths.TheDLOutputlevelforeachRFpathwillnotexceed5dBmandthecompositeoutput

powerwillnotexceed10dBm.

8.2.2.2.3 PowerRatio



Figure8‐13Status–BCUPowerRatio

 TargetedDLOutputPower:Displaysdesiredpowerratiosspecifiedbytheuser.Ifunithasnotbeen

commissioned,“NotCommissioned”willbedisplayed.

 ActualDLOutputPower:Displaysthecurrentlypowerratiosthatthesystemisusing.Thesevalues

willfluctuatebasedontheamountoftrafficthatisinthesystem.

8.2.2.2.4 Alarm

DisplaysthecurrentalarmstatusofeachindividualRFpath.ParametersforbothDLSignalLowandDLInput

OverloadcanbespecifiedfromtheControltab.



Figure8‐14Status–BCUAlarm







AdvancedRFTechnologies,Inc.  76



8.2.2.3 Status–RFU



Figure8‐15Status–RFU

8.2.2.3.1 Band

DisplaysthebandwidthandthefrequencyrangesforDLandULoftheRFUmodule.



Figure8‐16Status–RFUBand

8.2.2.3.2 Power&Gain(Admin/User)

 AdminMode‐ DisplaystheDownlinkInput/output,Downlink/UplinkAttenuation,andUplink

Output.

 UserMode‐DisplaystheDownlinkInput,Downlink/UplinkAttenuation,andUplinkOutput.



Figure8‐17Power&GainDisplay(Admin)



AdvancedRFTechnologies,Inc.  77



Figure8‐18Power&GainDisplay(User)

 Input[dBm]:DisplaystheDownlinkRFinputlevelwhichcomesfromtheADX‐H‐BCUorBTS.Thisvalueshould

bebetween0to25dBm.

 ALCAtten[dB]:TheamountofattenuationthatisbeingusedbythesystemwhenALCisactive.

 Atten[dB]:Theamountofattenuationthathasbeensetmanuallybytheuser.

 Output[dBm]:Thedownlink/uplinkoutputpoweroftheRFUandNOTtheoutputpoweroftheRU.

8.2.2.3.3 Alarm

DisplaysSystem,RF,andPowerAlarms.Ifanalarmispresentinthesystem,thenthecolorofthetabwill

changeaccordingtothetypeoffailure.

Table8‐8RFUAlarmStatus

AlarmSeverityDescription

System



LinkFailSoftFailAcomponentisphysicallyconnected,butthe

NMSisunabletocommunicatewithit.

OverTemperatureHardFail/

SoftFail

ThetemperatureofNMSishigherthanthe

thresholdlevelforovertemperaturealarm.

UnderTemperatureSoftFailThetemperatureofNMSislowerthanthe

thresholdlevelforundertemperaturealarm.

SystemHaltHardFail

Systemwillgointoa“SystemHalt”statewhena

hardfailalarmdoesnotclearafter10checks.

SystemHaltcanonlybeclearedwithapower

cycle,reboot,orfactorysettings.

RFAlarm



DLSignalnotdetectedSoftFailDownlinkinputsignalislowerthanthedefined

thresholdbyuser.

DLSignalLowSoftFailDownlinkinputsignalislowerthanthedefined

thresholdbyuser.

InputOverloadHardFail/

SoftFail

Downlinkinputsignalishigherthanthedefined

threshold.

OverpowerHardFail/

SoftFail

Uplinkoutputsignalishigherthanthedefined

thresholdbyuser.

PowerAlarm



ACFailSoftFailACpowerisnotoperatingwithinparameters.

DCFailSoftFailDCpowerisnotoperatingwithinparameters.

OverCurrentHardFailTotalcurrentofHEishigherthanthethreshold

levelforovercurrentalarm.

BatteryLowSoftFailVoltageofbatteryconnectedtoHEPSUislower

thanthedefinedthreshold.







AdvancedRFTechnologies,Inc.  78



8.2.2.4 Status–ODU



Figure8‐19Status‐ODU



8.2.2.4.1 Summary

TheSummarysectiondisplaysthenumberofremotemodulesthatarephysicallyconnected,thenumberof

soft/hard/linkfailalarms,andthenumberofRemoteModulethathavebeencommissionedandthenumberof

RemoteModulethatneedtobecommissioned.



Figure8‐20Summary(Status–ODU)



AdvancedRFTechnologies,Inc.  79



Table8‐9SummaryDescription

ParametersDescription

ConnectedDisplaysthenumberofRemoteModule’sconnectedtotheADX‐RACK‐ODU.

SoftFailDisplaysthetotalnumberofsoftfailpresent.

HardFailDisplaysthenumberofhardfailpresentoneachmodule.

LinkFailDisplaysthenumberoflinkfailpresentoneachmodule.

NotCommissionedDisplaysthenumberofnon‐commissionedorcommissionfailedmodule.

CommissionedDisplaythenumberofsuccessfullycommissionedmodule

8.2.2.4.2 RFStatus

DisplaystheDLinputpowerandtheULoutputpowerforeachODU.

AnADX‐RACK‐ODUiscomposedof2ODUs.



Figure8‐21RFStatus(Status–ODU)

8.2.2.4.3 OpticStatus

DisplayLDPowerandPDPowerforeachopticpath.LDPoweristhepowerthatisbeingsenttotheHPRand

PDPoweristhepowerthatisbeingreceivedfromtheRU.



Figure8‐22OpticStatus(Status–ODU)

8.2.2.4.4 OpticAtten(AdminOnly)

TheADX‐H‐ODUhas3typesofattenuators.

 DownlinkCommonAttenuator‐DisplaysthecommonattenuationlevelontheDLpath.

 UplinkCommonAttenuator‐DisplaysthecommonattenuationlevelontheULpath.

 UplinkOpticAttenuator‐Displaystheamountofattenuationusedateachopticallink.



AdvancedRFTechnologies,Inc.  80



Figure8‐23OpticAttenuation(Status–ODU)

8.2.2.4.5 OpticPathStatus

Displaystheopticstatusforeachopticpath



Figure8‐24OpticPathStatus(Status–ODU)

Table8‐10Descriptionforopticpathstatus

StatusDisplayDescription

LDStatus

NormalGreen,opticsignalbeingsenttoMasterHPRis>‐5dBm

LDfailOrange,opticsignalbeingsenttoMasterHPRis<‐5dBm

NotConnectedGray,noconnectionbetweenODUandMasterRU

PDStatus

NormalGreen,opticsignalbeingreceivedfromMasterHPR is>‐10dBm

PDfailOrange,opticsignalbeingreceivedfromMasterHPR is<‐10dBm

CommFailorNotConnectedGray,noconnectionbetweenODU andMasterRU





Downlink

Commonattenuator

Uplink

Commonattenuator

Uplink

Opticattenuator



AdvancedRFTechnologies,Inc.  81



8.2.2.5 Status–RUHub

RU‐HubisnotseparatemodulebutisintegratedintothemasterRU.ThepictureofHPRHubdisplayedon

webbasedGUIissameasthepictureofmasterRU.



Figure8‐25Status‐RUHub

8.2.2.5.1 RUAlarmStatus

TheHPRHubcansupportupto8remotemodules.TheHPRalarmstatusdisplaysthealarmstatusofeach

remotemodule.



Figure8‐26RUAlarmStatus(Status‐HPRHub)

8.2.2.5.2 RUCommissioningStatus

DisplaytheCommissioningstatusofeachRemoteModule.



Figure8‐27RUCommissioningStatus(Status‐RUHub)



AdvancedRFTechnologies,Inc.  82



Table8‐11DescriptionforRUCommissioningstatus

StatusDisplayDescription

InstalledStatusInstalledTextisblack

Not‐InstalledTextisgray

CommissioningStatusSuccessGreen

FailornotyetGray

8.2.2.5.3 Alarm

Table8‐12AlarmStatus(Status‐RUHub)

AlarmSeverity Description

SystemLinkFailSoftFail Presentwhenamodulecannotcommunicatewiththe

NMS

SystemHaltHardFail

Systemwillgointoa“SystemHalt”statewhenahard

failalarmdoesnotclearafter10checks.SystemHalt

canonlybeclearedwithapowercycle,reboot,or

factorysettings.

PowerAlarmACFailSoftFail ACpowerisnotwithinparameters.

DCFailSoftFail DCpowerisnotwithinparameters.

OverCurrentHardFail TotalcurrentofHPRishigherthanthethresholdlevel

forovercurrentalarm

BatteryLowSoftFail VoltageofbatteryconnectedtoHPR PSUislowerthan

thedefinedthreshold

8.2.2.6 Status–Remotemodule



Figure8‐28Status–RemoteModule



AdvancedRFTechnologies,Inc.  83



8.2.2.6.1 Band

Displaythespectrumthatisbeingused.Thebandcolumndisplaysthebandwidththathasbeenused.The

downlinkcolumndisplaysthecenterfrequencyoftheuseddownlinkband.Theuplinkcolumndisplaysthecenter

frequencyoftheuseduplinkband.



Figure8‐29PCSBandInformation(Status–RemoteModule)

8.2.2.6.2 Power&Gain(Admin/User)

DisplaytheDownlinkoutput,Downlink/UplinkAttenuation,andUplinkInput/output.



Figure8‐30Power&Gain(Admin)



Figure8‐31Power&Gain(User)

 Admin

o Input[dBm]:DisplaystheRFinputlevelforUplinkonlyfortheRemoteModule.

o ALCAtten[dB]:TheamountofattenuationusedwhenALCisactivate.

o Atten[dB]:Theamountofattenuationmanuallysetbytheuser.

o [M]Output[dBm]:OutputpowerofRFtransceiver(1

stageamplification).

o [H]Output[dBm]:OutputpowerofdownlinkHPA(2

stageamplification).

 User

o Input[dBm]:DisplaystheRFinputlevelforUplinkonlyfortheRemoteModule.

o Atten[dB]:Theamountofattenuationmanuallysetbytheuser.

o Output[dBm]:Displaysthetotalcompositeoutputpower.







AdvancedRFTechnologies,Inc.  84



8.2.2.6.3 OpticPower(Master‐RUOnly)

DisplaytheLDPowerandPDPowerofopticmoduleinsidetheMasterRU.



Figure8‐32OpticPower(Status–MasterHPRonly)

8.2.2.6.4 OperatingStatus

Table8‐13OperatingStatus(Status–RemoteModule)

AlarmSeverity Description

SystemLinkFailSoftFail NocommunicationwithNMS.

OverTemperatureHardFail

/SoftFail

Temperatureishigherthanthethresholdlevelfor

overtemperaturealarm.

Under

TemperatureSoftFail Temperatureislowerthanthethresholdlevelfor

undertemperaturealarm.

SystemHaltHardFail

SystemhaltoneithertheMasterHPR orSlaveRU.

Systemhaltoccurswhenahardfailalarmfailsto

clearafter10checks.

ORULDFailSoftFail LDFailpresentintheMasterRU’sopticunit.

ORUPDFailSoftFail PDFailpresentintheMasterRU’sopticunit.

RFAlarmInputOverloadHardFail Uplinkinputsignalishigherthanthedefined

threshold.

OverPowerHardFail

/SoftFail

Downlinkoutputsignalishigherthanthedefined

thresholdbyuser.

VSWRSoftFail Triggeredwhenpowerisbeingreflectedbackto

thesystem,typicallyduetoalooseconnector.

PowerAlarmACFailSoftFail ACpowerisnotoperatingwithinparameters.

DCFailSoftFail DCpowerisnotoperatingwithinparameters.

OverCurrentHardFail TotalcurrentofHPRishigherthanthethreshold

levelforovercurrentalarm.

BatteryLowSoftFail VoltageofbatteryconnectedtoHEPSUislower

thanthedefinedthreshold.







AdvancedRFTechnologies,Inc.  85



8.2.3 ControlTab

8.2.3.1 Control–NMS



Figure8‐33Control‐NMS

8.2.3.1.1 HeartbeatTime

AllowstheusertoenableordisableSNMPtrapsfrombeingsentoutandalsospecifytheHeartbeatinterval.

Timeanddatestampsofthelast2heartbeatswillbedisplayedinthe“Lastheartbeatsentout”section.



Figure8‐34Heartbeat(Control–NMS)

8.2.3.1.2 HESystem

AllowstheusertoperformaHEsystemrebootorHEfullsystemfactorysettings



Figure8‐35HESystemReboot&FactorySetting(Control–NMS)

8.2.3.1.3 NMSSystem

AllowstheusertoperformaNMSUnitrebootorNMSfactorysettings



Figure8‐36NMSSystemReboot&FactorySetting(Control–NMS)



AdvancedRFTechnologies,Inc.  86



8.2.3.2 Control–BCU



Figure8‐37Control–BCU

8.2.3.2.1 ManualATTControl



Figure8‐38Control–BCUManualATTControl

 Downlink:AllowstheusertomanuallyadjusttheDLattenuationlevelsforeachRFpath.Adjusting

thesesettingsisnotrecommendedsinceitwillchangethepowerratiossetbytheuser.

 Uplink:AllowstheusertomanuallyadjusttheULattenuationlevelsforeachRFpath.Adjustingthese

settingsisnotrecommended,unlessadditionalattenuationisneededontheULpath.

 DLOutputALCLevel:AllowstheusertomanuallysettheDLOutputALCLevelsforeachRFpath.

Adjustingthesesettingsisnotrecommendedsinceitwillchangethepowerratiossetbytheuser.

ThesesettingsareautomaticallysetbythesystemduringtheBCUcommissioningprocess.This

sectionalsodisplaysthecompositeDLOutputALCLevelwhichisthevaluethatcanbeusedto

commissiontheRFU.





메모 [C22]: BCUH추가여부검토



AdvancedRFTechnologies,Inc.  87



8.2.3.2.2 Reboot/FactorySetting

AllowstheuserrebootorrestorefactorysettingsoftheBCU.



Figure8‐39Control–BCUReboot/FactorySetting



8.2.3.2.3 AlarmSetting



Figure8‐40Control–BCUAlarmSetting

 DownlinkInputOverload:AllowstheusertospecifythelevelatwhichtheDLInputOverloadalarmis

triggered.Valuesrangefrom0dBmto+25dBm.

 DownlinkSignalLow:AllowstheusertospecifythelevelatwhichtheDLSignalLowalarmistriggered.

Valuesrangefrom‐10dBmto+20dBm.

 DownlinkInputOverloadAlarmOn:AllowstousertoenableordisabletheInputOverloadAlarm

 [Path–A/B/C]DownlinkSignalLowAlarmOn:AllowstheusertoenableordisabletheDLSignalLow

alarmforeachRFpath.

8.2.3.3 Control–RFU



Figure8‐41Control‐RFU





AdvancedRFTechnologies,Inc.  88



8.2.3.3.1 GeneralSetting

Toenableanyofthesettings,clickonthecheckboxandclicktheApplybutton.



Figure8‐42GeneralSetting(Control–RFU)(Admin)

 

Figure8‐43GeneralSetting(Control–RFU)(User)

Table8‐14DescriptionforGeneralSetting

NameDescriptionAvailableAccounts

DownlinkALCEnablesordisablesDownlinkALCAdministrator

UplinkALCEnablesordisablesUplinkALCAdministrator

DownlinkONEnablesordisablestheRFUDownlinkpath Administrator,User

UplinkONEnablesordisablestheRFUUplinkpathAdministrator,User

UplinkNoiseDetDisplaysifthemoduleisturnedonoroffduetotheULNoiseDetection

Routine

Administrator

8.2.3.3.2 Reboot/FactorySetting

AllowstheuserrebootorrestorefactorysettingsoftheRFU.



Figure8‐44Reboot&FactorySetting(Control–RFU)

8.2.3.3.3 UplinkNoiseDetection(AdminOnly)



Figure8‐45ULNoiseDetection(Control–RFU)



AdvancedRFTechnologies,Inc.  89



The“ULNoiseDet”buttonwilltakeyoutotheULNoiseDetectionpagewhichwillallowyoutoruntheULNoise

Detectionroutine.



Figure8‐46ULNoiseDetection‐PCSband

TheAutoULnoisemeasurementroutinecanberunbyclickingontheCheckbutton.AfterallULnoise

measurementhavebeentaken,thelevelsforeachULpathwillbedisplayedandalongwiththedifference

betweenminimumdetectlevelandmeasureddetectlevel.

TheuserwillbeabletoseewhichpathisgeneratingtheelevatedULnoiselevelbasedonthemeasureddetect

levelanddifferencevalue.

TonavigatebacktotheRFUcontrolpage,clickontheControltabagain.



8.2.3.3.4 ManualAttenControl

  

   (Admin)(User)

Figure8‐47ManualAttenuatorControlSetting(Control–RFU)

Table8‐15DescriptionforMainGainControlSetting(Control–RFU)

NameDescriptionRangeStepAvailableAccounts

DownlinkAttenuatorDownlinkAttenuatortobeadjustedmanually 0~25dB 0.5dB Administrator,User

UplinkAttenuatorUplinkAttenuatortobeadjustedmanually 0~35dB 0.5dB Administrator,User

DLOutputALCLevelTosettheMaxoutputALClevel‐10~0dBm 0.5dBm Administrator

ULOutputALCLevelTosettheMaxoutputALClevel‐20~0dBm 0.5dBm Administrator,User



AdvancedRFTechnologies,Inc.  90



DLOutputALCOffsetTosettheMaxoutputALCOffset‐10~0dBm 0.5dBm Administrator

ULOutputALCOffsetTosettheMaxoutputALCOffset‐20~0dBm 0.5dBm Administrator

8.2.3.3.5 AlarmSetting



Figure8‐48AlarmThresholdSetting(Control–RFU)

Table8‐16DescriptionforAlarmThresholdSetting(Control–RFU)

NameDescriptionRangeDefault

threshold

DownlinkSignalLowAllowstheusertospecifytheminimumincomingDLinputsignallevel

beforetriggeringa“DownlinkSignalLow”soft‐failalarm.‐10~20dBm‐5dBm

DownlinkSignalNot

Detected

AllowstheusertospecifytheminimumincomingDLinputsignallevel

beforetriggeringa“DownlinkSignalNotDetected”soft‐failalarm.‐10~20dBm‐10dBm

UplinkOverPowerAllowstheusertospecifythehowstrongtheoutputsignalofuplinkcan

bebeforetriggeringan“UplinkOverPower”HardFailalarm.‐20~0dBm0dBm







AdvancedRFTechnologies,Inc.  91



8.2.3.4 Control–ODU



Figure8‐49Control–ODU

8.2.3.4.1 OpticAttenuation(AdminOnly)



Figure8‐50OpticAttenuation–ODU



AdvancedRFTechnologies,Inc.  92



Table8‐17DescriptionforOpticAttenuation(Control–ODU)

NameDescriptionRangeDefault

threshold

DL/ULcommonAT

AllowstheusertocontroloverallopticDL/ULpathgain. 0~30dB 5dB

DLAT

UsedtocompensateDLopticloss.0~13dB 13dB

ULATTUsedtocompensateULopticloss.0~13dB 13dB



8.2.3.4.2 Reboot/FactorySetting

AllowtheusertoperformODUrebootorODUfactorysettings.



Figure8‐51Reboot&factorySetting(Control–ODU)

8.2.3.5 Control–RHHub



Figure8‐52Control–RUHub

8.2.3.5.1 Reboot/FactorySetting

AllowstheusertoperformHPRHubrebootorHPRHubfactorysettings



Figure8‐53Reboot&FactorySetting(Control–RUHub)



AdvancedRFTechnologies,Inc.  93



8.2.3.6 Control–RemoteModule(MasterorSlaveRU)



Figure8‐54Control–RemoteModule

8.2.3.6.1 GeneralSetting(Admin/User)



   (Admin)(User)

Figure8‐55GeneralSetting(Control‐RU)

Table8‐18DescriptionforGeneralSetting(Control‐RU)

NameDescriptionAvailableAccounts

DownlinkALC

ThissettingallowsyoutoenableordisablethedownlinkALCfunction.When

ALCisenabled,thedownlinkoutputpowerwillnotexceedtheDownlink

OutputLevelspecifiedintheManualAttenControlsection.

Administrator

DownlinkOnThissettingallowsyoutoenableordisabletheDownlinkpath. Administrator,User

UplinkALC

ThissettingallowsyoutoenableordisabletheuplinkALCfunction.WhenALC

isenabled,theUplinkoutputpowerwillnotexceedtheUplinkOutputLevel

specifiedintheManualAttenControlsection.

Administrator

UplinkOnThissettingallowsyoutoenableordisabletheUplinkpath. Administrator,User



AdvancedRFTechnologies,Inc.  94



8.2.3.6.2 Reboot/FactorySetting

AllowstheusertoRebootorrestoreFactorySettingsontheremotemodule.



Figure8‐56Reboot&factorySetting(Control‐RU)

8.2.3.6.3 OpticSetting(OnlyMasterRU)(AdminOnly)



Figure8‐57OpticSetting(Control‐RU)

Table8‐19DescriptionforOpticSetting(Control‐RU)

NameDescriptionRangeStepAvailable

Accounts

DownlinkOpticAttenRFattenuatortocompensatetheopticlossof

downlink0~13.0dB0.5dBAdministrator

PDPowerIncomingpowerlevelfromtheODU   Administrator

LDPowerOutgoingpowerleveltotheODUAdministrator



8.2.3.6.4 ManualAttenuatorControl



(Admin)    (User)

Figure8‐58ManualAttenControl(Control‐RU)



AdvancedRFTechnologies,Inc.  95



Table8‐20DescriptionforManualAttenControl(Control‐RU)

NameDescriptionRangeDefault

threshold

AvailableAccounts

DownlinkAttenAllowstheusertospecifyhowmuchattenuationtouse.0~30dB30dBAdministrator,User

UplinkAttenAllowstheusertospecifyhowmuchattenuationtouse.0~25dB25dBAdministrator,User

DLOutputALC

Level

Theremotemodulewillpreventthedownlinkoutput

powerfromexceedingthespecifiedvalue.5~43dBm43dBmAdministrator,User

ULOutputALC

Level

Thesystemwillpreventtheoutputpowertoexceedthe

specifiedvalue.0~10dBm 5or

6dBmAdministrator

DLOutputALC

Offset

Whentheincomingsignallevelincreases,thesystemwill

notadjustthegainlevelsuntilitreachestheALCOffset

Level.

0~10dB5dBAdministrator,User

ULOutputALC

Offset

Whentheincomingsignallevelincreases,thesystemwill

notadjustthegainlevelsuntilitreachestheALCOffset

Level.

0~10dB3dBAdministrator

8.2.3.6.5 AlarmSetting



Figure8‐59AlarmSetting(Control‐RU)

 DLOverPowerLimit:Theoverpoweralarmthresholdcanbeadjustedfrom5~43dBm.+2dBfromtheDL

overpowerlimitwilltriggerasoftfailand>2dBwilltriggerahardfailalarm

 VSWRAlarmON:EnableordisablestheVSWRAlarm.





AdvancedRFTechnologies,Inc.  96



8.2.4 InstallTab

8.2.4.1 Install–NMS



Figure8‐60Install‐NMS

8.2.4.1.1 HECommissioningStatus



Figure8‐61HECommissioningStatus(Install–NMS)

Table8‐21DescriptionforHECommissioningStatus(Install–NMS)

StatusDisplayDescription

InstalledStatusPhysicallyInstalledTextisblack

PhysicallyNot‐InstalledTextisgray

CommissioningStatus

SuccessGreen

Failornot

commissionedGray



AdvancedRFTechnologies,Inc.  97



8.2.4.1.2 SNMP



Figure8‐62SNMP(Install–NMS)

TheSNMPsectionallowsyoutospecifytheSiteIDandManagerIP.TheSite‐IDisthecodethatisusedto

identifyaparticularmodule.TheManagerIPfieldiswheretheuserinputstheIPaddressoftheNOCsystemthat

isbeingusedtomonitortheSNMPtraps.



8.2.4.1.3 Location

Thissectionallowstheusertoinputthelatitudeandthelongitudeoftherepeater.



Figure8‐63LocationSetting(Install–NMS)

 SelectNorSfromthedropdownmenuforLatitude

 SelectEorWfromthedropdownmenuforLongitude

 Inputthefirst3numbersofthelatitude/longitudeinthetextareaafterthe“+”andbeforethe“.”

 Inputthelast6numbersofthelatitude/longitudeinthetextareaafterthe“.”



8.2.4.1.4 ExternalModemBoxSettings

ThissectionallowstheusertospecifyanalternativeIP,SubnetMask,andGatewaysettings.Thesesettings

areenabledwhentheHost/RemoteswitchissettotheRemoteposition.



Figure8‐64ExternalModemBoxSetting(Install–NMS)



8.2.4.1.5 Description



AdvancedRFTechnologies,Inc.  98



ThissectionallowstheusertosavethedescriptionofNMS.



Figure8‐65Description(Install–NMS)



8.2.4.1.6 SNMPAgentFalseAlarmTest

Thissectionallowstheusertogeneratebothsoftandhardfailalarms.Afteralarmsaregenerated,theNOC

canpolltheADXtoseeifalarmsarepresent.Allalarmsgeneratedduringthistestarefalsealarms.



Figure8‐66SNMPAgentFalseAlarmTest(Install–NMS)



8.2.4.1.7 LocationInfo/InstallerInfo

Thissectionallowstheusertospecifytheaddressoftherepeaterandalsotheinformationoftheinstaller.



Figure8‐67 LocationInfo/InstallerInfo(Install–NMS)





AdvancedRFTechnologies,Inc.  99



8.2.4.1.8 Date&Time

Thissectionallowstheusertospecifythecurrentdateandtime.



Figure8‐68Date&TimeSetting(Install–NMS)

8.2.4.2 Install–BCU



Figure8‐69Install–BCU





AdvancedRFTechnologies,Inc.  100



8.2.4.2.1 BCUCommissioning



Figure8‐70Install–BCUCommissioning

 CurrentDLInputLevel:

 DLInputCommissioningLevel:

 TargetedDLOutputPowerRatio:

 CommissioningProgress:

 PreviousDLCommissioningLevel:

 LastCommissioningDate:

 LastCommissioningTime:

8.2.4.2.2 Description



Figure8‐71Install–BCUDescription

 BCU:ThissectionallowstheusertosetthedescriptionofBCU.

 PathA/B/C:AllowstheusertospecifyanameforeachRFpath.ThenamesofeachRFpathwill

appearinthecolumnheaders.



8.2.4.3 Install–RFU



AdvancedRFTechnologies,Inc.  101



Figure8‐72Install‐RFU





AdvancedRFTechnologies,Inc.  102



8.2.4.3.1 RFUCommissioning

ThissectionallowstheusertoperformRFUcommission.ToperformRFUcommissioning,selectaDLInput

CommissioningLevelfromthedropdownmenuandclickApply.Thecommissioningprogressisdisplayedonthe

CommissioningProgressbar.Anyerrors,warnings,andmessageswillappearviaapopupwindow.Pleasereferto

theADXInstallationGuidetodeterminetheproperRFUcommissioninglevels.



Figure8‐73RFUCommissioning(Install–RFU)

8.2.4.3.2 Description

ThissectionallowstheusertosetthedescriptionofRFU.



Figure8‐74Description(Install–RFU)



8.2.4.4 Install–ODU



Figure8‐75Install–ODU

8.2.4.4.1 OpticCommissioning

Thissectionwillallowtheusertoperformanyopticcompensationifitisnecessary.TheCommissioning

buttonwillturnorangeifopticcompensationisneeded.



AdvancedRFTechnologies,Inc.  103



Figure8‐76Opticcontrol(Control–ODU)

Table8‐22DescriptionforOpticcontrol(Control–ODU)

Display&ControlDescription

Opticlossislessthan5dBo

Opticlossismorethan5dBo

NotconnectedtoaRU

Noopticlosscompensationisneeded.



Opticlosscompensationisneeded.

NotconnectedtoaRU

8.2.4.4.2 Description

ThissectionallowstheusertosavethedescriptionofODU.



Figure8‐77Description(Install–ODU)

8.2.4.5 Install–HPRHub



AdvancedRFTechnologies,Inc.  104



Figure8‐78Install‐RUHub

8.2.4.5.1 RUCommissioningStatus



Figure8‐79RUCommissioningStatus(Install‐RUHub)

Table8‐23DescriptionforHPRCommissioningstatus

StatusDisplayDescription

InstalledStatusPhysicallyInstalledTextisblack

PhysicallyNot‐InstalledTextisgray

CommissioningStatusSuccessGreen

FailornotcommissionedGray



8.2.4.5.2 Description

ThissectionallowstheusertosavethedescriptionofHPRHub.



Figure8‐80Description(Install‐RUHub)

8.2.4.6 Install–RemoteModule(MasterorSlaveRU)



AdvancedRFTechnologies,Inc.  105



Figure8‐81Install‐RemoteModule

8.2.4.6.1 RUOutputCommissioning

ThissectionallowstheusertoperformHPRcommission.ToperformHPRcommission,selectaDLOutput

CommissioningLevelfromthedropdownmenuandthenclickApply.Thecommissioningprogressisdisplayedon

theCommissioningProgressbar.Anyerrors,warnings,andmessageswillappearviaapopupwindow.



Figure8‐82RUOutputCommissioning(Install‐RU)





AdvancedRFTechnologies,Inc.  106



8.2.4.6.2 Description

Thissectionallowstheusertosavethedescriptionofremotemodule.



Figure8‐83Description(Install‐RemoteModule)

8.2.5 System

TheSystemtaballowstheusertoperformfirmwareupdates,uploadcloseoutpackages,viewanychangesto

thesystem,backupexistingconfiguration,andadd/removeuseraccounts,andchangethelogincredentialsofthe

Administrator.

8.2.5.1 System:Account

8.2.5.1.1 System:Account‐AccountManagement(AdminOnly)

TheAccountManagementsectionallowstheAdministratortodeleteanyuser/guestaccount.Pleasenote

thattheAccountManagementsectionisonlyavailableifyouareloggedintothesystemastheAdministrator.To

deleteauser/guestaccountclickontheAccountManagementlinkandundertheDeletecolumn,clickonthe

deletebutton.



Figure8‐84AccountManagement

8.2.5.1.2 System:Account‐NewAccount(AdminOnly)

TheNewaccountsectionallowstheAdministratortocreateanewuser/guestaccount.Pleasenotethatthe

newaccountsectionisonlyavailableifyouareloggedintothesystemastheAdministrator.Tocreateanew

user/guestaccountclickonthenewaccountlinkandfillinthefieldshighlightedinyellowasshownbelow.



Figure8‐85NewAccount





AdvancedRFTechnologies,Inc.  107



8.2.5.1.3 System:Account‐ChangePassword

TheChangePasswordsectionallowsthecurrentuserwhoisloggedintothesystemtochangetheirlogin

credentials.



Figure8‐86ChangePassword



8.2.5.2 System:Logs

8.2.5.2.1 System:Logs‐EventLog

Thissectiondisplayssystemeventsthathavetakenplace.TheEventLogdisplayswhohasmadethechanges,

thetimeanddateofwhentheeventtookplace,andwhatchangesweremadetothesystem.TheSystemLog

tracksthefollowingevents:

 SystemInitiation

 AlarmSet

 AlarmClear



Figure8‐87EventLog



AdvancedRFTechnologies,Inc.  108



8.2.5.2.2 System:Logs‐UserLog

Thissectiontracksuseractivitywithinthesystem.TheUserLogdisplayswhohasmadethechanges,thetime

anddateofwhentheeventtookplace,andwhatchangesweremadetothesystem.TheUserLogtracksthe

followingitems:

 Login/Logoutactivity

 Changestogain/attenuation/outputvalues

 Systemeventgeneratedbyuser(firmwareupdate,backup/resote,create/deleteaccount)

 DASNavigationTreeLock/Unlock

 Descriptionchange

 Repeater/installerinformationchange

 Settingdate/time



Figure8‐88UserLog

8.2.5.3 System:Update

 Toperformafirmwareupdate,clickontheSystem:Updatetabandthefollowingscreenwillshowup.



Figure8‐89Systemupdate

 Clickonthe‘Browse’buttonandlocatethefirmwarefile.

 ClickontheUpdatebuttontoperformthefirmwareupdate.

 Oncethefirmwareupdateiscomplete,thefollowingmessagewillappear.



AdvancedRFTechnologies,Inc.  109



Figure8‐90MessageafterSystemupdateiscomplete

8.2.5.4 System:SystemInformation

8.2.5.4.1 System:SystemInformation



 SystemInformationCheck

TheSystemInformationCheckbuttonwillchecktheADXconfiguationandreportpossiblediscrepancies.



 SystemInformation

ThissectiondisplaysthegeneralsysteminformationoftheADXDAS.



Figure8‐91SystemInformation



AdvancedRFTechnologies,Inc.  110



 SystemNotification

Thissectionisdisplayedonlywhenthefollowingconditionsarepresent:

‐ WhenmultipleremotemoduleswithsamefrequencybandexistinaRU.

‐ WhentheremotemoduledoesnotmatchwiththeRFUbeingused.



Figure8‐92SystemNotification

 BOM

BOMdisplaysallpartsthatareconnectedtotheADX‐H‐NMS.

TheBOMcanbedownloadedasaCSVfilebyclickingthe‘Download’buttonatthebottomright.



Figure8‐93Billofmaterial



8.2.5.5 System:Backup/Restore



AdvancedRFTechnologies,Inc.  111



 SettingsBackup

ClickingtheBackupwillcreateatemporarybackupfilestoredinsideoftheADX.Oncethefileiscreated,itwill

needtobedownloadedtoacomputer.Adownloadbuttonwillappearafterthebackupfilehasbeencreated.If

theADXispowercycledorrebooted,thenthetemporarybackupfilewillbelost.Werecommenddownloading

thebackupfileimmediatelyafterithasbeencreated.ClickontheDownloadbuttontodownloadthebackupfile.



Figure8‐94SettingBackup(Before)



Figure8‐95SettingBackup(After)



 SettingRestore



AdvancedRFTechnologies,Inc.  112



Restorefunctioncanbeusedtorestorethesavedsettingsfromthebackupfile.Oncethebackupfileisloaded,

thetreeinthefigurebelowwillappear.Checktheboxesofthemodulesthatyouwouldliketorestoreandthen

clickthe“Restore”buttonatthebottomonthissection.

WerecommendcreatinganewbackupfileifaddingorremovingmodulesfromtheADX.Discrepancies

betweenthebackupfileandtheexistingtreecouldcauserestoreerrors.



Figure8‐96SettingRestore

8.2.5.6 System:SNMP

 SNMPV1/V2

ThissectionallowsyoutoaddcommunitystringsforSNMPv1andv2.



Figure8‐97SNMPV1/V2





AdvancedRFTechnologies,Inc.  113



 SNMPV3

ThissectionallowstheusertoaddaccountsforSNMPv3.



Figure8‐98SNMPV3

8.2.5.7 System:CloseoutPackage

ThecloseoutpackagesectionwillallowtheusertouploaddocumentstotheADX‐H‐NMS.Themaximumfile

sizeforeachuploadislimitedto10MB.Thetotalamountofspaceavailableforuploadingdocumentis100MB.

Pleasedonotusethissectionastheprimarystoragelocationofyourdocuments.Documentsmaybecome

unavailableifthesystemgoesdown.



Figure8‐99System‐CloseoutPackage

Touploaddocumentstothemodule,clickonthe“Browse”buttonandlocatethefilethatyouwouldliketo

upload,thenenterinaDescriptionofthefilebeinguploaded.Afterwards,clickonthe“AddFile”buttontoupload

thefile.Belowiswhatyouwillseeafterthefileupload.Todeletethefile,clickonthedeletebuttonlocatedinthe

lastcolumn.



Figure8‐100System‐CloseoutPackageafterthefileupload





AdvancedRFTechnologies,Inc.  114



8.2.6 Help

Ifaninternetconnectionisavailable,clickingontheHelpTabwillredirecttheusertoourTechnicalSupport

page.



Figure8‐101Help

8.2.7 Logout

ClickingtheLogoutbuttonwilllogthecurrentuseroffthesystem.

8.3 GuestMode

Whenloggingintothesystemasaguest,theguestwillonlyhaveread‐onlyprivilegesandwillnotbeableto

makeanychangestothesystem.



AdvancedRFTechnologies,Inc.  115



9. SYSTEM‐WIDESPECIFICATION(TOBECONNECTEDTOHEVIAOPTICLINE)

700LTE/CELL/SMR800 Specifications.

700F CELL SMR800 Comments

Frequency

Downlink

Lower

ABC 728-746MHz

869-894MHz 851~869MHz SMR800 is not

for FCC approval

Upper

C 746-757MHz

Uplink

Lower

ABC 698-716MHz

824-849MHz 806~824MHz

Upper

C 776-787MHz

Support Band Width 16+11MHz

(Lower ABC + Upper C) 25MHz 18MHz

DL Input Range 0~25dBm 0~25dBm 0~25dBm

Gain Range

D/L 18~43dB, 0.5dB step, ATT range: 0~25dB

U/L -5~30dB, 0.5dB step, ATT range: 0~35dB

Attenuation

Range

D/L 0~25dB

U/L 0~35dB

Accuracy 0~15dB: < ±0.5dB, 15~35dB: < ±1.0dB, 35dB~: < ±1.5dB

Gain Flatness < ±2.0dB < ±2.0dB < ±2.0dB

Composite Maximum

Output Power

Downlink 43dBm±1dB

Uplink -15dBm±1dB

Noise Figure @max gain 5.0dB

@ Band Center

5.0dB

@ Band Center

5.0dB

@ Band Center

VSWR < 1.5:1

EVM

LTE Uplink (< 12.5%), downlink (< 8%)

EVDO Uplink (< 14.75%), downlink (< 12.5%)

CDMA2000 Uplink (< 14.75%), downlink (< 14.75%)

Optical Loss 0~10dBo

System Delay <2us @0dBo optic loss

Spurious FCC, 3GPP TS 36.104, 3GPP2 C.S0010-C

Operating Temperature -30~55C

Operating Humidity 5-90%

메모 [H23]: SMR800 의경우

FCC 인증에서제외함.(ACP 문제점)



AdvancedRFTechnologies,Inc.  116



NOTE:IndustryCanadaCellularband20dBnominalbandisfromXMHztoYMHzforDownlinkandfromX

MHztoYMHzforUplink.

2. PCS/AWS/BRS Specifications.

PCS AWS BRS Comments

Frequency

Downlink 1930~1995MHz 2110~2155 MHz

2496~2690 MHz

Uplink 1850~1915MHz 1710~1755 MHz

Support Band Width 65MHz 45MHz 194MHz

DL Input Range 0~25dBm 0~25dBm

+12~37dBm

(Medium Mode)

-15~12dBm

(Low Mode)

Gain Range

D/L 21~46dB, 0.5dB step, ATT range: 0~25dB

U/L -5~30dB, 0.5dB step, ATT range: 0~35dB

Attenuation

Range

D/L 0~25dB

U/L 0~35dB

Accuracy 0~15dB: < ±0.5dB, 15~35dB: < ±1.0dB, 35dB~: < ±1.5dB

Gain Flatness < ±2.0dB < ±2.0dB < ±2.0dB

Composite Maximum

Output Power

Downlink 46dBm±1dB

Uplink -15dBm±1dB

Noise Figure @max gain 5.0dB

@ Band Center

5.0dB

@ Band Center

5.0dB

@ Band Center

VSWR < 1.5:1

EVM

LTE Uplink (< 12.5%), downlink (< 8%)

EVDO Uplink (< 14.75%), downlink (< 12.5%)

CDMA2000 Uplink (< 14.75%), downlink (< 14.75%)

Optical Loss 0~10dBo

System Delay <2us @0dBo optic loss

Spurious FCC, 3GPP TS 36.104, 3GPP2 C.S0010-C

Operating Temperature -30~55C

Operating Humidity 5-90%

메모 [Y24]: Addition14/05/12



AdvancedRFTechnologies,Inc.  117



NOTE:IndustryCanadaCellularband20dBnominalbandisfromXMHztoYMHzforDownlinkandfromX

MHztoYMHzforUplink.

3. SMR900 Specifications.

SMR9000+Paging Comments

Frequency

Downlink 929~942MHz

Uplink 896~903MHz

Support Band Width DL:13MHz,

UL: 7MHz

DL Input Range 0~25dBm

Gain Range

D/L 18~43dB, 0.5dB step, ATT range: 0~25dB

U/L -5~30dB, 0.5dB step, ATT range: 0~40dB

Attenuation

Range

D/L 0~25dB

U/L 0~40dB

Accuracy 0~15dB: < ±0.5dB, 15~35dB: < ±1.0dB, 35dB~: <

±1.5dB

Gain Flatness < ±2.0dB

Composite Maximum

Output Power

Downlink 43dBm±1dB

Uplink -15dBm±1dB

Noise Figure @max gain 5.0dB@ Band Center

VSWR < 1.5:1

EVM

LTE Uplink (< 12.5%), downlink (< 8%)

EVDO Uplink (< 14.75%), downlink (< 12.5%)

CDMA2000 Uplink (< 14.75%), downlink (< 14.75%)

Optical Loss 0~10dBo

System Delay <2us @0dBo optic loss

Spurious FCC, 3GPP TS 36.104, 3GPP2 C.S0010-C

Operating Temperature -30~55C

Operating Humidity 5-90%

메모 [Y25]: Addition14/05/12

메모 [H26]: 해당제품의SPEC 의경우

향후추가될제품의SPEC 임.



AdvancedRFTechnologies,Inc.  118



NOTE:IndustryCanadaCellularband20dBnominalbandisfromXMHztoYMHzforDownlinkandfromX

MHztoYMHzforUplink.

4. WCS Specifications.

WCS Comments

Frequency

Downlink 2305-2315MHz

Uplink 2350-2360MHz

Support Band Width 10MHz

DL Input Range +12~37dBm(Medium)

-15~12dBm(Low)

Gain Range

D/L 19.8~44.8dB, 0.5dB step, ATT range: 0~25dB

U/L -5~30dB, 0.5dB step, ATT range: 0~40dB

Attenuation

Range

D/L 0~25dB

U/L 0~40dB

Accuracy 0~15dB: < ±0.5dB, 15~35dB: < ±1.0dB, 35dB~: <

±1.5dB

Gain Flatness < ±2.0dB

Composite Maximum

Output Power

Downlink 44.8dBm±1dB

Uplink -15dBm±1dB

Noise Figure @max gain 5.0dB@ Band Center

VSWR < 1.5:1

EVM

LTE Uplink (< 12.5%), downlink (< 8%)

EVDO Uplink (< 14.75%), downlink (< 12.5%)

CDMA2000 Uplink (< 14.75%), downlink (< 14.75%)

Optical Loss 0~10dBo

System Delay <2us @0dBo optic loss

Spurious FCC, 3GPP TS 36.104, 3GPP2 C.S0010-C

Operating Temperature -30~55C

Operating Humidity 5-90%

메모 [Y27]: Addition14/05/12

메모 [C28]: 주파수수정2015.07.28



AdvancedRFTechnologies,Inc.  119



NOTE:IndustryCanadaCellularband20dBnominalbandisfromXMHztoYMHzforDownlinkandfromX

MHztoYMHzforUplink.



10. MECHANICALDRAWING



Figure10‐1HEDrawing

메모 [Y29]: Addition14/05/12



AdvancedRFTechnologies,Inc.  120



Figure10‐2HPRDrawing

메모 [H30]: 6band 로모델명

수정필요함

ADRF KOREA ADX-HPR-C DAS (Distributed Antenna System) User Manual

ADRF KOREA, Inc. DAS (Distributed Antenna System)

User Manual

Navigation menu

Namespaces

Views

Navigation