ADTRAN BSAP2135 Outdoor Wireless Access Point User Manual Bluesocket 2135 Access Point Quick Start Guide

Download:
Mirror Download [FCC.gov]
Document ID	2753307
Application ID	nj/41sdQKjS19topRp9bYw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	68.93kB (861674 bits)
Date Submitted	2015-09-18 00:00:00
Date Available	2015-09-24 00:00:00
Creation Date	2008-02-15 15:11:52
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2015-07-09 17:46:08
Document Title	Bluesocket 2135 Access Point Quick Start Guide
Document Creator	FrameMaker 12.0
Document Author:	ADTRAN EN Technical Publications

CONFIGURING THE BSAP’S IP ADDRESS USING THE CLI
By default, DHCP is enabled on the BSAP 2135. However, if you need to statically configure the IP
address or statically configure AP discovery for the BSAP, follow these steps:
1. Ensure that the BSAP is connected to a controlling computer (using the provided RJ-45 Ethernet
cable).
2. Specify that the computer’s TCP/IP setting is On or Enabled by navigating to Control Panel >
Network Connections and double-clicking the connection of your network interface card. Select
Internet Protocol (TCP/IP) and select Properties. Then specify that the TCP/IP setting is enabled.
3. Set your PC to a static IP address of 192.168.190.2 with a subnet mask of 255.255.255.0.
4. Next, access the BSAP’s command line interface (CLI) using an SSH client. Open an SSH
connection using the unit’s default IP address (192.168.190.1) and port 2335 connected to the
LAN1 port on the BSAP. To access the unit using vWLAN, and for more instructions about CLI
configuration, refer to the Bluesocket vWLAN Administrator’s Guide, available online at
https://supportforums.adtran.com.
CONFIGURING THE APPLICATION
BLUESOCKET 2135 ACCESS POINT
P/N 1700962F1
HARDWARE
The following items are included in your shipment:
•
Bluesocket 2135 Access Point (BSAP)
•
One plane bracket with hardware
- Four expansion bolts with washers and nuts
- Four hex cap screws with washers and lock washers
•
One pole mounting base with hardware
- One hose strap
- Four round head screws with washers and lock washers
•
Watertight PoE fitting
•
Grounding cable
More detailed documentation for configuring the BSAP 2135 is provided in the Bluesocket vWLAN
Administrator’s Guide, available online at https://supportforums.adtran.com.
Antenna Connectors
FCC RADIO FREQUENCY INTERFERENCE
This device complies with Part 15 of the Federal Communications Commission (FCC) rules. The
operation of this device is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including interference that may cause undesired
operation.
THIRD-PARTY SOFTWARE
The software included in the Bluesocket 2135 contains copyrighted software that is licensed under the
GNU General Public License (GPL). For a list of third-party software and their licenses, go to
http://www.adtran.com/software/EULA. You can obtain the complete corresponding source code of such
software components from ADTRAN for a period of three years after our last shipment of this product by
sending a money order or check for $5 to:
ADTRAN, Inc, P.O. Box 933638, Atlanta, GA 31193-3638
Please write GPL Source for product Bluesocket 2135 in the memo line of your payment.
This offer is valid to anyone in receipt of this information.
Grounding Point
Watertight
PoE Fitting
ANTENNAS
The BSAP 2135 provides six N-type antenna connectors (no integrated antennas are included). These
connectors support two internal 802.11 radios: one 2.4 GHz 802.11b/g/n radio and one 5 GHz
802.11a/n/ac radio. There are three antenna connectors for each band labeled 2.4GHz and 5GHz. A set
of six high-efficiency omnidirectional antennas can be ordered from ADTRAN for the BSAP 2135
(P/N 1700930F1, three 5 GHz, 7 dBi gain and three 2.4 GHz, 5 dBi gain).
Make a note of the 12-character MAC address and 14-digit serial number
listed on the back of the BSAP 2135 before mounting the AP to a wall or other
surface. This information will be required during configuration.
Copyright © 2015 ADTRAN, Inc. All Rights Reserved.
Quick Start Guide, 61700962F1-13B, May 2015
MOUNTING THE BSAP TO AN EXTERIOR CEILING OR WALL
Ground the BSAP
BSAPs can be mounted in exterior applications or interior applications in harsh environments with an
operating temperature range of -40°F to 131°F (-40°C to 55°C). BSAPs should be positioned for
maximum throughput and range between other APs and wireless client devices. Follow these
instructions to mount the BSAP 2135 to a ceiling or wall:
1. On a flat mounting surface, mark the locations of the four mounting holes using the plane bracket as
a template (Figure 1).
2. Drill an 8 mm diameter hole with a depth of 36 to 38 mm into each of the markings (Figure 2).
3. Hammer the expanding bolts into each of the drilled holes (Figure 3).
Use the supplied green grounding cable to ground the BSAP 2135 by following these steps:
Expansion Bolts
1.
2.
3.
Remove bottom hex head screw from the BSAP unit. This location of the grounding screw is
marked . .. .
Place the ground lug of the supplied grounding cable on the shank of the screw and secure the
screw to the unit using an appropriate tool.
Attach the other end of the grounding cable to a reliable earth ground point.
Adequate grounding must be provided to the unit. A clearly marked
grounding location is provided on the front of the unit for this
purpose. Consult a certified electrician to ensure that all
grounding and cabling is installed in compliance with the local
electrical code.
CONNECTING TO THE BSAP
If the BSAP is to be powered using a network device such as a switch, connect the Ethernet port of the
BSAP to the appropriate switchport. Obtain the IP address of the BSAP from the Dynamic Host Control
Protocol (DHCP) server (based on the MAC address of the BSAP). DHCP is enabled by default. You
can then use a Secure Shell (SSH) client to connect to the BSAP based on the instructions below.
If the BSAP is powered using a PoE injector, connect the Ethernet port of the BSAP to the OUT port of
the PoE injector and connect the Ethernet port of the computer to the IN port on the PoE injector. Then
proceed to SSH to the default IP address of the BSAP as instructed below.
Plane Bracket
4.
5.
6.
Place the lock washers, then the flat washers on the four hex cap screws, and drive the screws
through the plane bracket into the back of the case (Figure 4).
Install the antennas (sold separately) onto the appropriate antenna ports. The antenna ports are
labeled 2.4GHz and 5GHz.
Insert the expansion bolts extending from the mounting surface through the holes in the plane
bracket, place the flat washers on the bolts, thread the nuts onto the bolts, and tighten to secure the
bracket to the mounting surface (Figure 5).
Mount Unit on
Expansion Bolts
Mount Plane Bracket
to Unit
CONFIGURING THE BSAP WITH VWLAN AND AP DISCOVERY
The BSAP 2135 can be configured for use with the Bluesocket virtual wireless local area network
(vWLAN). If you have installed vWLAN, and want to use AP discovery to configure the BSAP 2135,
follow these steps. For more information on the vWLAN and AP discovery, refer to the vWLAN AP
Discovery configuration guide available online at https://supportforums.adtran.com.
1. After powering the AP and connecting it to the network, allow the AP to discover the vWLAN
appliance to receive its configuration information. This AP discovery process uses an algorithm
that attempts discovery methods in this order: static configuration, DHCP vendor option (43),
Domain Naming System (DNS) discovery, and cached vWLAN information. If no response to the
discovery request is received, the algorithm moves to the next method in the list (except when
using static configuration, which never queries the other discovery methods).
2. There are two additional network components that can be configured to facilitate AP discovery.
First, an external DHCP server can be configured to assign IP addresses to APs associated with
the vWLAN. When configuring the DHCP server, make sure to configure the Bluesocket DHCP
vendor option (43) on the server. Second, you can configure an external DNS server to resolve the
name apdiscovery to the IP address of the vWLAN instance in the network environment.
USING THE 5 GHZ U-NII BAND IN EUROPE, AUSTRALIA, NEW ZEALAND
Expansion Bolt
In Europe, Australia and New Zealand the 5 GHz U-NII low band (5150 to 5250 GHz, channels 36, 40,
44, and 48) is designated for indoor use only. If the BSAP 2135 is installed indoors, for example in a
harsh environment such as a warehouse, it must configured for indoor use.
To enable this band/channels for indoor installation, follow these steps:
In the graphical user interface (GUI) navigate to Configuration > Wireless > Access Points. Select
the appropriate access point link to display the configuration menu. Using the Installed drop-down list,
select Indoor.
Hex Cap Screw
Support - Phone: 888-423-8726
Quick Start Guide, 61700962F1-13B, May 2015
MOUNTING THE BSAP TO A POLE
•
•
•
•
•
In all cases the BSAP 2135 should be connected to Earth Ground.
In all cases 802.3at PoE injectors with GR-1089-Core Criteria B surge
protection should be used.
For outdoor applications, use only shielded or outdoor-rated Ethernet
cable run inside conduit to protect it from damage from extreme
weather conditions and temperatures.
Consult a certified electrician to ensure that all grounding and cabling
is installed in compliance with local electrical code.
Any damage or malfunction resulting from exposure of this unit to
lightning or transient voltage events will void the user's warranty.
INDOORS
OUTDOORS
The BSAP 2135 also ships with a pole mount base and hose strap to mount the AP to a vertical or
horizontal pole. BSAPs should be positioned for maximum throughput and range between other APs
and wireless client devices.
To mount the BSAP 2135 to a vertical pole:
1. Place the lock washers, then the flat washers on the four hex cap screws, and drive the screws
through the plane bracket into the back of the case as shown in Figure 4.
2. Using the four round head screws with washers and lock washers, attach the pole mounting bracket
to the plane bracket in a vertical position (Figure 6).
3. Thread the open end of the hose strap through the two tabs on the pole mount base (Figure 7).
4. Install the antennas (sold separately) onto the appropriate antenna ports. The antenna ports are
labeled 2.4GHz and 5GHz.
5. Wrap the hose strap around the vertical mounting pole and insert the end into the strap lock.
Tighten the strap lock to secure the unit to the pole (Figure 10).
BSAP 2135
with Built-in
Ethernet and
Antenna Surge
Protection
NetVanta PoE
Protector/Injector
(1702595F15)
PoE Switch
Round Head
Screw
OR
Non-PoE Switch
Pole Mount
Base in
Vertical Position
NetVanta PoE
Protector/Injector
(1702595F15)
with Optional AC Power
Adapter (1700501F1)
Hose Strap
Insertion
To Earth Ground
Ethernet Cable
Outdoor Shielded Ethernet Cable
Mesh Link
Ground Cable
Drip Loop
ADTRAN recommends forming a 3 to 5-inch drip loop
on outdoor cables where water could run along the
cable and enter the BSAP 2135, PoE injector, or
building. If the cables are oriented so that water
cannot possibly enter, drip loops are not necessary.
PowerDsine PD-9001GO
Outdoor 802.3at PoE Injector
or Equivalent with
GR-1089-Core Criteria B
Surge Protection
BSAP 2135
with Built-in
Ethernet and
Antenna Surge
Protection
To Earth Ground
Support - Phone: 888-423-8726
Quick Start Guide, 61700962F1-13B, May 2015
To mount the BSAP 2135 to a horizontal pole:
1. Place the lock washers, then the flat washers on the four hex cap screws, and drive the screws
through the plane bracket into the back of the case as shown in Figure 4.
2. Drive the four round head screws to attach the pole mount base to the plane bracket in a horizontal
position (Figure 8).
3. Thread the open end of the hose strap through the two tabs on the pole mount base (Figure 9).
4. Install the antennas (sold separately) onto the appropriate antenna ports. The antenna ports are
labeled 2.4GHz and 5GHz.
5. Wrap the hose strap around the horizontal mounting pole and insert the end into the strap lock.
Tighten the lock of the hose strap to secure the unit to the pole (Figure 11).
Round Head
Screw
1.
2.
3.
4.
5.
6.
7.
Disassemble the watertight fitting by unscrewing the cinch nut and pushing the rubber gasket out
of the strain-relief fitting.
Thread the cinch nut onto the customer-provided RJ-45 CAT 5e or CAT 6 cable.
Spread the gasket open and wrap it around the cable near the RJ-45 connector.
Insert the RJ-45 connector through the strain-relief fitting, and press the gasket back into its
original position.
Insert the connector into the RJ-45 receptacle on the bottom of the BSAP.
Gently push the strain-relief fitting along the cable until it engages with the black threads, and
screw it onto the BSAP until it is well seated against the unit.
Screw the cinch nut onto the strain-relief fitting until it is well seated against the gasket forming a
watertight seal.
5GHz
5GHz
Antenna
Connectors
Strain-relief
Fitting
Hose Strap
Insertion
10
RJ-45 Receptacle
and Connector
Gasket
Pole Mount
Base in
Horizontal Position
Cinch Nut
For outdoor applications, the watertight fitting must be used when
connecting PoE cables to the BSAP 2135. Failure to use the watertight
fitting when the unit is installed outdoors will void the user's warranty and
could create a fire or shock hazard.
11
Connect the BSAP to a PoE Source
Vertical
Pole
Mounting
Horizontal Pole
Mounting
The BSAP 2135 requires 802.3at PoE. It will not function using 802.3af PoE. The following diagram
illustrates how to provide power to the BSAP 2135 installed outdoors. Three examples are provided:
1. A PoE switch providing power in conjunction with NetVanta PoE Protector/Injector (1702595F15)
installed indoors.
2. A non-PoE switch in conjunction with NetVanta PoE Protector/Injector (1702595F15) and an
optional AC Power Adapter (1700501F1) to provide power installed indoors.
3. A third-party outdoor rated 802.3at PoE injector (PowerDsine PD-9001GO) or equivalent with
GR-1089-Core Criteria B Surge Protection installed outdoors with mesh.
SUPPLYING POWER TO THE BSAP
The BSAP 2135 does not have a power switch. It is powered when connected to a network device that
supplies PoE based on the IEEE 802.3at standard or an external PoE injector. To power the BSAP
2135, follow these instructions:
Connect the PoE Cable to the BSAP
Support - Phone: 888-423-8726
Quick Start Guide, 61700962F1-13B, May 2015

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Creator                         : ADTRAN EN Technical Publications
Title                           : Bluesocket 2135 Access Point Quick Start Guide
Create Date                     : 2008:02:15 15:11:52Z
Creator Tool                    : FrameMaker 12.0
Modify Date                     : 2015:07:09 17:46:08+08:00
Metadata Date                   : 2015:07:09 17:46:08+08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Keywords                        : 61700962F1-13A, 1700962F1, Bluesocket 2135, WAP, AP, Quick Start Guide, wireless, access point, controller, QSG
Copyright                       : 2012
Document ID                     : uuid:f25b4e69-c708-4b17-8fa2-f11d61b2a7c2
Instance ID                     : uuid:416d3edb-c510-4194-ab7a-0b1dceffeaa6
Page Count                      : 4
Language                        : en
Author                          : ADTRAN EN Technical Publications

EXIF Metadata provided by EXIF.tools