AIRTAME APS AT-DG2 The Airtame 2 is an all-in-one wireless screen sharing solution. User Manual Safety manual

Download:
Mirror Download [FCC.gov]
Document ID	4109939
Application ID	ArsyA1GfB60h14Eg+e5deg==
Document Description	Safety manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	82.34kB (1029203 bits)
Date Submitted	2018-12-19 00:00:00
Date Available	2018-12-19 00:00:00
Creation Date	2018-12-13 12:48:50
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-12-13 12:48:51
Document Title	Safety manual
Document Creator	Adobe InDesign CC 13.1 (Macintosh)

Airtame 2
Contents
How to use, safety, regulatory and warranty information
For more information, visit airtame.com/support
What’s in the box?
Airtame 2
USB C
­ irtame 2
The A
­ irtame 2 is connected with the Aircord USB
Type C.
Aircord
Y-shaped cable splitting from USB Type C into HDMI
and USB Type A. HDMI is plugged into the HDMI port
on the TV / projector. The USB A is plugged into
the ­Power Supply. The USB C is plugged into the
­Airtame 2.
Power supply
The Power supply is required to power the ­Airtame 2.
Use only the power supply provided with this Airtame
2, or other approved Airtame powering accessories.
Important: The ­Airtame 2 should not be powered by
plugging the USB A into the TV / projector. It is not an
adequate power source and is not recommended.
Kensington Slot
Reset button
Micro USB
USB A
Cable splitter
USB C
HDMI
Non-removable adhesive
Important: We advise that you only use the
non-­removable adhesive once you have chosen a
­permanent location for the ­Airtame 2.
• Be careful when using the power supply and only
use this in combination with the ­Airtame 2 in dry
locations to avoid the risk of electric shock.
The ­Airtame 2 has been designed with high attention
to the safety of the user. However, if used improperly,
the ­Airtame 2 can potentially cause fire, electrical
shock or personal injury. To avoid any accidents,
please pay attention to these guidelines:
• Use only the power supply and Aircord provided in
the box, or a PoE to USB Adaptor recommended by
Airtame. Using other cables or power supplies can
potentially damage or influence the functionalities
during use.
Magnetic wall mount
• Do not extend the USB part of the Aircord.
Non-removable adhesive
Power supply
EU power adapter
For a permanent mounting, use the non-removable
adhesive on the back of the magnetic wall mount, and
attach it to a hard surface, such as a wall.
Non-removable adhesive
On the back of the Aircord cable splitter, and on the
magnetic wall mount, are a set of protective seals
• Do not attempt to disassemble or repair the
­Airtame 2 yourself. Doing so voids the limited
­warranty and could harm you, your TV/projector,
and/or the A
­ irtame 2.
Safety precautions
Aircord
Magnetic wall mount
The magnetic wall mount can be magnetically fixed to
the ­Airtame 2 from the back, and is used for mounting
the ­Airtame 2.
For a flexible mounting, attach the magnetic wall
mount to a magnetic area without removing the
protective seal.
covering non-removable adhesives.
Each non-removable adhesive is optional and can be
used to stick to a clean surface, such as a wall, and
other non-magnetic areas.
Power supply and US power adapter
UK power adapter
• The ­Airtame 2 generates heat during use that
results in a temperature increase of the surface of
the ­Airtame 2. Therefore, you should let it cool down
before removing from your TV / projector and handle
with caution.
• Stop the use of the ­Airtame 2 immediately if it (i)
functions in an abnormal manner, (ii) produces
unusual sounds, (iii) produces unusual odors or (iv) if
it becomes too hot to touch.
• Do not expose the A
­ irtame 2 including the Aircord
or power supply to water or extreme conditions
(moisture, heat, cold, dust) as it potentially could
result in a malfunction.
• Do not place the Airtame 2 in direct sunlight.
• The non-removable adhesives on the magnetic wall
mount and the Aircord may leave marks or release
the plastic part and remain on the wall.
• Note: The Airtame 2 has been tested for use with
the power extension cable at a maximum length of
3m (10’11 ft).
• When running at full capacity, the ­Airtame 2 can be
hot to touch. If you wish to remove it, unplug the
­Airtame 2’s power source and let the ­Airtame 2 cool
down before touching it.
• Do not mount the ­Airtame 2 on a hot surface as
this can increase its temperature and the risk of
functionality failing.
• The recommended environmental operating
­temperature of the ­Airtame 2 is: 5 °C to 30 °C
(41 °F to 86 °F).
The recommended Operating Humidity is
20-90%RH non-condensing.
• Do not use the Airtame 2 outdoors.
• WARNING: Choking hazard. Some Airtame 2
accessories may present a choking hazard to small
children. Keep these accessories away from small
children.
Warning regarding magnetism
Legal notices
Avoid placing any media that contains magnets or is
sensitive to magnetism, such as bank cards, audio/
video, tapes, or magnetic memory devices, near the
magnetic wall mount. Media containing information sensitive to magnets should be kept at least
5 cm (2 inches) away from the product. Similarly,
­magnet-sensitive devices, such as a mechanical
watch or measuring device, can be damaged if they
come too close to the magnetic wall mount.
Model: AT-DG2
FCC ID: 2ADEFAT-DG2
IC:
12460A-ATDG2
License agreement
The software license terms related to the ­Airtame 2
can be found at airtame.com/terms.
When using the ­Airtame 2, you acknowledge and
accept those terms.
General terms
The use of any products by Airtame ApS are governed
by the Terms of Service and End User License
Agreement which can be found at
airtame.com/terms.
When using Airtame ApS products you acknowledge
and accept those terms.
Warranty information
Warranty information can be found at
airtame.com/terms.
The latest versions of this manual
Please find the latest version of this manual on the
company website:
airtame.com/support
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
FCC Caution
Any changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate this equipment.
IEEE 802.11n operation of this product in the U.S.A. is
firmware-limited to channels 1 through 11.
Wireless Radio Use
This device is restricted to indoor use when operating
in the 5.15 to 5.25 GHz frequency band.
Important note		
FCC Radiation Exposure Statement:
To satisfy FCC and IC exposure requirements, a
separation distance of at least 20 cm (8 inches) should
be maintained between the antenna of this device and
persons during device operation. Operations at closer
than this distance are not recommended.
The antenna used for this transmitter must not be
co-located in conjunction with any other antenna or
transmitter.
Note to US model owner
To comply with US FCC regulation, the country
selection function has been completely removed from
all US models.
The availability of some specific channels and/or
operational frequency bands are country dependent
and are firmware programmed at the factory to match
the intended destination. The firmware setting is not
accessible by the end user.
Industry canada (ic) notices
English			
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful
communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
French
Conformément à la réglementation d’Industrie
Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou
inférieur) approuvé pour l’émetteur par Industrie
Canada.
Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il
faut choisir le type d’antenne et son gain de sorte que
la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l’intensité nécessaire à l’établissement
d’une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le
fonctionnement.
Radiation Exposure Statement
Cet appareil est conforme aux limites d’exposition aux
rayonnements de la IC CNR-102 définies pour un environnement non contrôlé. Afin d’éviter la possibilité
de dépasser les limites d’exposition aux fréquences
radio de la IC CNR-102, la proximité humaine à
l’antenne ne doit pas être inférieure à 20cm (8 pouces)
pendant le fonctionnement normal.
Wireless Radio Use
Cet appareil est restreint à usage en interieur pour la
bande de fréquence 5.15-5.25 Ghz.
European union
AIRTAME ApS declares that this equipment is in
compliance with the essential requirements and other
provisions of Directive 2014/53/EU.
The full Declaration of Conformity can be found at
airtame.com/support/cemarking.
Waste management of AIRTAME follows the WEEE
Directive 2012/19/EU and the RoHS recast Directive
2011/65/EU. More information can be found at
airtame.com/terms.
­ irtame 2 is designed by
AIRTAME ApS, airtame.com/about
www.airtame.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : da-DK
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c143 79.161424, 2017/09/22-11:52:47
Create Date                     : 2018:12:13 12:48:50+01:00
Metadata Date                   : 2018:12:13 12:48:51+01:00
Modify Date                     : 2018:12:13 12:48:51+01:00
Creator Tool                    : Adobe InDesign CC 13.1 (Macintosh)
Instance ID                     : uuid:232d4e6b-6c38-af4a-9d78-84f847e29572
Original Document ID            : xmp.did:EE7F1174072068118DBBFE674B209159
Document ID                     : xmp.id:7e845688-b2f7-4f12-8e0d-b739985a0d1f
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:c111d256-d965-4e71-b43b-e4ef138aed18
Derived From Document ID        : xmp.did:11471009-fff1-4db2-9ea9-1f29fab3c9f2
Derived From Original Document ID: xmp.did:EE7F1174072068118DBBFE674B209159
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.1 (Macintosh)
History Changed                 : /
History When                    : 2018:12:13 12:48:50+01:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 4
Creator                         : Adobe InDesign CC 13.1 (Macintosh)

EXIF Metadata provided by EXIF.tools