AISOLUTION KDC470 Barcode Scanner User Manual Appendix G KDC470
AISOLUTION CO., LTD. Barcode Scanner Appendix G KDC470
User Manual
Copyright © KOAMTAC Inc. 2016
KDC User Manual
R
Rev 2.85T.A3
(KDC20/30/410/411/415/420/421/425/430)
3.x7.A3
(KDC100/200/250/300/350/350WA/450)
A001.05.08 (KDC500)
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Table of Contents
WARRANTY POLICY
1.INTRODUCTION
1.1
KDC Package Contents ......................................................................................................... 21
1.2
KDC Characteristics............................................................................................................... 23
1.3
Keypad Functionality for KDC350 ......................................................................................... 27
1.4
Keypad Functionality for KDC500 ......................................................................................... 28
1.5
Input data by using a keypad (KDC350) ................................................................................ 29
1.6
Turn on the power of KDC20/30/350/400/500 ...................................................................... 30
2.INSTALLATION
2.1
Bluetooth Pairing .................................................................................................................. 32
Preparing for Pairing .............................................................................................................. 32
Pairing ................................................................................................................................... 35
2.2
KOAMTAC Installation Wizard .............................................................................................. 40
Windows 7, 8 & 10 ................................................................................................................. 40
Android .................................................................................................................................. 42
iPad/iPhone/iPod Touch ......................................................................................................... 42
3.OPERATING YOUR KDC
3.1
Getting Started ..................................................................................................................... 43
Attaching a Lanyard or Hand Strap to a KDC ........................................................................... 43
Charge KDC Battery ................................................................................................................ 44
Configure KDC ........................................................................................................................ 44
3.2
Basics
..................................................................................................................................... 46
Reading Barcodes................................................................................................................... 46
Read Barcodes with GPS Coordinates (KDC250G/350G) .......................................................... 47
Reading NFC Tags (KDC350N/400N/KDC500) .......................................................................... 47
Reading HF RFID Tags (KDC450/470) ...................................................................................... 48
Inputting Data by Using a Keypad (KDC350) ............................................................................ 48
Read Magnetic-Stripe (MS) Card(KDC500) .............................................................................. 48
Read Integrated Chip (IC) Card(KDC500) ................................................................................. 49
Synchronizing data to the host device .................................................................................... 49
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
3.3
KDC Menu ............................................................................................................................. 50
KDC Mode Menu .................................................................................................................... 62
View Data Menu .................................................................................................................... 62
Set Barcodes Menu ................................................................................................................ 62
Code Options Menu ............................................................................................................... 62
Scan Options Menu ................................................................................................................ 62
Data Process Menu ................................................................................................................ 65
BT Config Menu – KDC20/30/200/250/300/270/350/400/500 ................................................ 71
BT Service Menu – KDC20/30/200/250/300/270/350/400/500 ............................................... 73
GPS Config Menu – KDC250G/350G........................................................................................ 73
USB Mode Menu– 100M/200M/250M/300M/270/350 .......................................................... 74
NFC Config Menu – KDC350N/411N/415N/421N/425N/500 ................................................... 76
UHF Config Menu – KDC450U ................................................................................................. 76
WIFI Config Menu (KDC350F) ................................................................................................. 77
CDMA Config Menu (KDC350WA CDMA) ................................................................................ 78
MSR Config Menu – KDC415/425/430/500 ............................................................................. 79
ICCR Config Menu – KDC500 ................................................................................................... 81
SystemConfig Menu ............................................................................................................... 82
Key Mgmt Menu– KDC500 ..................................................................................................... 85
Sensitive Menu – KDC500 ....................................................................................................... 86
3.4
LED Status ............................................................................................................................. 87
3.5
Empty Battery ........................................................................................................................ 87
KDC100/200/250/300/270/350 .............................................................................................. 87
KDC20/30/400 ....................................................................................................................... 87
KDC500 .................................................................................................................................. 87
3.6
Buffer Full .............................................................................................................................. 88
3.7
Reset Feature (100/200/250/300) or Power-on/off (KDC20/30/270/350/400/500) ............... 89
3.8
Replace Battery ..................................................................................................................... 90
4.BLUETOOTH -KDC20/30/200/250/300/270/350/400/500
4.1
Bluetooth Config ................................................................................................................... 91
Connect Device ...................................................................................................................... 91
Auto Connect ......................................................................................................................... 92
Auto Reconnect ..................................................................................................................... 92
Auto Power On
....................................................................................................................... 92
PWR ON Time
......................................................................................................................... 92
Auto Power Off
....................................................................................................................... 92
Beep Warning
......................................................................................................................... 93
PWR OFF Time
........................................................................................................................ 93
PowerOFF Msg
....................................................................................................................... 93
MAC Address
.......................................................................................................................... 93
FW Version
............................................................................................................................. 93
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Wakeup Nulls
......................................................................................................................... 93
Autolock Time
........................................................................................................................ 93
HID Keyboard
......................................................................................................................... 94
HID Initial and Inter-Character Delay
....................................................................................... 94
Control Character Transmission in HID mode .......................................................................... 94
Function Key Transmission in HID mode ................................................................................. 95
Disconnect/Reconnect/BT(HID) Toggle ................................................................................... 95
4.2
Bluetooth Service .................................................................................................................. 96
Power
.................................................................................................................................... 96
Pairing
.................................................................................................................................... 96
Discovering
............................................................................................................................. 97
Connect To ............................................................................................................................ 97
HID Sync ................................................................................................................................ 97
Tips ........................................................................................................................................ 97
Auto Pairing
............................................................................................................................ 98
5.SYNCHRONIZATION
5.1
KTSync Menu ...................................................................................................................... 100
5.2
File Menu ............................................................................................................................ 102
Connect to KDC .................................................................................................................... 102
Synchronize ......................................................................................................................... 102
Erase KDC Memory .............................................................................................................. 102
Bluetooth ............................................................................................................................. 103
Configuration ....................................................................................................................... 104
Synchronization Settings ................................................................................................................. 105
Destination of Data .............................................................................................................. 105
Synchronization Methods ..................................................................................................... 106
Current KDC Wedge Method ................................................................................................ 107
Synchronization Options ...................................................................................................... 108
Application Options.............................................................................................................. 108
5.3
Barcode & KDC Settings ..................................................................................................... 109
Select Symbologies and Symbology Options ......................................................................... 109
Data Editing Option .............................................................................................................. 110
5.4
Other Settings ..................................................................................................................... 111
5.5
Mobile pKTSync .................................................................................................................. 112
5.6
Android aKTSync ................................................................................................................. 114
KDC and Android Pairing ...................................................................................................... 114
Launch KTSync ..................................................................................................................... 114
Keyboard Wedge ................................................................................................................. 116
5.7
iPad/iPhone/iPod Touch KTSync......................................................................................... 117
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
KDC20i/30i/200i/250i/300i/270i/350i/400i/500i connection using MFi mode ....................... 117
iKTSync Settings ................................................................................................................... 117
How to Connect and Reconnect MFi Mode using UP Keys..................................................... 118
How to use Keyboard Wedge with iKTSync ........................................................................... 119
5.8
Blackberry bKTSync ............................................................................................................. 121
5.9
KTSync for Mac OS X .......................................................................................................... 123
Connect Button .................................................................................................................... 123
Disconnect Button ............................................................................................................... 123
Synchronize Button .............................................................................................................. 124
Clear Button ......................................................................................................................... 124
Settings Button .................................................................................................................... 124
6.APPLICATION GENERATION
6.1
Application Generation ....................................................................................................... 127
Generate Application ........................................................................................................... 128
Data Filter Settings ............................................................................................................... 129
Application Download and Execution ................................................................................... 131
6.2
Predefined Applications ...................................................................................................... 132
Master/Slave ....................................................................................................................... 132
Pick/Bin ............................................................................................................................... 132
DB Lookup Application ......................................................................................................... 136
Inventory Application ........................................................................................................... 137
7.TROUBLESHOOTING
8.WARRANTY
9.CONTACT INFORMATION
10.APPENDIX A – BARCODE & SCAN OPTIONS
10.1
Symbologies ........................................................................................................................ 143
Bookland EAN vs. EAN-13 ..................................................................................................... 143
Add-on Symbologies ............................................................................................................ 144
10.2
Code Options (KDC20/100/200/250/270L/410/411/415/470L) ............................................ 145
Reverse Direction ................................................................................................................. 145
Symbology Conversion ......................................................................................................... 145
Verification of Optional “Check Digit” ................................................................................... 146
Transmission of “Check Digit”............................................................................................... 146
Resolution of Inconsistencies ............................................................................................... 147
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
10.3
Miscellaneous Barcode Information .................................................................................... 148
Height of a Linear Barcode ................................................................................................... 148
Check Characters ................................................................................................................. 148
Prevent Interleave 2 of 5 Partial Reading .............................................................................. 148
Data Buffer Full .................................................................................................................... 149
11.APPENDIX B –FAQ
11.1
Symbology .......................................................................................................................... 150
11.2
Host Interface ...................................................................................................................... 151
11.3
Battery
................................................................................................................................. 151
11.4
Memory
................................................................................................................................ 152
11.5
Programming
........................................................................................................................ 152
12.APPENDIX C – 1D SPECIAL BARCODES
(KDC20/20D/100/200/250/350L/350D/410/415)
12.1
Set Symbologies ................................................................................................................. 154
12.2
Barcode Options ................................................................................................................. 156
12.3
Delete Last Scanned Barcode ............................................................................................. 158
12.4
Scan Options ....................................................................................................................... 160
12.5
Scan Timeout ...................................................................................................................... 160
12.6
Minimum Barcode Length ................................................................................................... 161
12.7
ScanIfConnect ..................................................................................................................... 164
12.8
Security Level(Laser model only) ......................................................................................... 165
12.9
Data Process - Wedge/Store, Enter Key & Extend Key ....................................................... 166
12.10
Data Process - Data Edit ................................................................................................. 167
12.10 Data Process - Data Format & Handshake ............................................................................ 168
12.11 Data Process - Termination Character & Duplicate Check .................................................... 169
12.11
Bluetooth ......................................................................................................................... 170
12.12
Bluetooth Auto Power On Time ...................................................................................... 173
12.13
Bluetooth Power Off Time .............................................................................................. 174
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
12.14
HID Auto Lock Time ........................................................................................................ 176
12.15
HID Keyboard .................................................................................................................. 177
12.16
HID Initial Delay ............................................................................................................... 178
12.17
HID Character Delay ....................................................................................................... 179
12.18
HID Control Character .................................................................................................... 180
12.19
System ............................................................................................................................. 181
12.20
Sleep Timeout ................................................................................................................. 185
12.21
ETC .................................................................................................................................. 186
12.22
Function .......................................................................................................................... 187
12.23
Number ........................................................................................................................... 187
12.24
Lower Case Alphabet ...................................................................................................... 189
12.25
Upper Case Alphabet ...................................................................................................... 191
12.26
Control Character ............................................................................................................ 193
12.27
Symbol Character ............................................................................................................ 194
12.28
GPS (GPS Model Only) .................................................................................................... 197
12.29
GPS/BT Auto Power Off Timeout .................................................................................... 198
12.30
NFC (NFC Model Only) ................................................................................................... 199
12.31
USB Disk (M Model Only) ................................................................................................ 200
12.32
USB DM Button(KDC20/20D Only) .................................................................................. 200
12.33
WIFI (WIFI Model Only) ................................................................................................... 201
12.34
Multilanguage ................................................................................................................. 202
13.APPENDIX D – 2D SPECIAL BARCODES (KDC30/300/350C/350WA/420/425/450)
13.1
Set Symbologies ................................................................................................................. 203
13.2
Barcode Options ................................................................................................................. 203
13.3
Delete Last Scanned Barcode ............................................................................................. 203
13.4
Scan Options ....................................................................................................................... 204
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
13.5
Scan Timeout ...................................................................................................................... 205
13.6
Minimum Barcode Length (except KDC30) ......................................................................... 206
13.7
Image Capture (except KDC30) .......................................................................................... 209
13.8
ScanIfConnect ..................................................................................................................... 209
13.9
Data Process - Wedge/Store, Enter Key & Extend Key ....................................................... 210
13.10
Data Process - Data Edit ................................................................................................. 211
13.11
Data Process – Data Format & Handshake ..................................................................... 212
13.12
Data Process - Termination Character & Duplicate Check ............................................. 213
13.13
Bluetooth ......................................................................................................................... 214
13.14
Bluetooth Auto Power On Time ...................................................................................... 217
13.15
Bluetooth Power Off Time .............................................................................................. 218
13.16
HID Auto Lock Time ........................................................................................................ 220
13.17
HID Keyboard .................................................................................................................. 221
13.18
HID Initial Delay ............................................................................................................... 222
13.19
HID Character Delay ....................................................................................................... 223
13.20
HID Control Character .................................................................................................... 224
13.21
System ............................................................................................................................. 225
13.22
Sleep Timeout ................................................................................................................. 229
13.23
Function .......................................................................................................................... 230
13.24
Number ........................................................................................................................... 231
13.25
Lower Case Alphabet ...................................................................................................... 232
13.26
Upper Case Alphabet ...................................................................................................... 234
13.27
Control Character ............................................................................................................ 236
13.28
Symbol Character ............................................................................................................ 237
13.29
GPS (GPS Model Only) .................................................................................................... 240
13.30
GPS/BT Auto Power Off Timeout .................................................................................... 241
13.31
NFC (NFC Model Only) ................................................................................................... 242
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
13.32
UHF (UHF Model Only) ................................................................................................... 242
13.33
USB Disk (M Model Only) ................................................................................................ 245
13.34
USB DM Button(KDC30 only) .......................................................................................... 245
13.35
WIFI (WIFI Model Only) ................................................................................................... 246
13.36
CDMA (KDC350WA CDMA Model Only) ........................................................................ 248
13.37
Multilanguage ................................................................................................................. 249
14.APPENDIX E - MSR SPECIAL BARCODES (KDC415/425MSR)
14.1
KDC415MSR ........................................................................................................................ 250
14.2
KDC425MSR ........................................................................................................................ 253
15.APPENDIX F – 1D SPECIAL BARCODES (500D)
15.1
Set Symbologies ................................................................................................................. 256
15.2
Barcode Options ................................................................................................................. 259
15.3
Delete Last Scanned Barcode ............................................................................................. 261
15.4
Scan Options ....................................................................................................................... 262
15.5
Scan Timeout ...................................................................................................................... 262
15.6
Minimum Barcode Length ................................................................................................... 263
15.7
ScanIfConnect ..................................................................................................................... 266
15.8
Data Process - Wedge/Store, Enter Key & Extend Key ....................................................... 267
15.9
Data Process - Data Edit ..................................................................................................... 267
15.10
Data Process - Data Format ............................................................................................ 268
15.11
Data Process - Termination Character & Duplicate Check ............................................. 269
15.12
Bluetooth ......................................................................................................................... 270
15.13
System ............................................................................................................................. 271
15.14
Sleep Timeout ................................................................................................................. 274
15.15
NFC ................................................................................................................................. 275
15.16
MSR ................................................................................................................................. 275
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
15.17
ICCR(IC CARD READER) ................................................................................................. 277
15.18
Key Management ............................................................................................................ 277
15.19
Multilanguage ................................................................................................................. 277
16.APPENDIX G – 2D SPECIAL BARCODES (KDC500C)
16.1
Set Symbologies ................................................................................................................. 279
16.2
Barcode Options ................................................................................................................. 279
16.3
Delete Last Scanned Barcode ............................................................................................. 279
16.4
Scan Options ....................................................................................................................... 280
16.5
Scan Timeout ...................................................................................................................... 281
16.6
Minimum Barcode Length ................................................................................................... 282
16.7
ScanIfConnect ..................................................................................................................... 285
16.8
Data Process - Wedge/Store, Enter Key & Extend Key ....................................................... 285
16.9
Data Process - Data Edit ..................................................................................................... 286
16.10
Data Process – Data Format ............................................................................................ 287
16.11
Data Process - Termination Character & Duplicate Check ............................................. 287
16.12
Bluetooth ......................................................................................................................... 288
16.13
System ............................................................................................................................. 289
16.14
Sleep Timeout ................................................................................................................. 292
16.15
NFC ................................................................................................................................. 293
16.16
MSR ................................................................................................................................. 293
16.17
ICCR(IC CARD READER) ................................................................................................. 295
16.18
Key Management ............................................................................................................ 295
16.19
Multilanguage ................................................................................................................. 296
17.APPENDIX G – MULTIPLE SPECIAL BARCODES
17.1
KDC20/100/250/270L/350L/410/411/415/470L/500L
............................................................. 297
17.2
KDC30/270C/300/350C/420/421/425/450/470C/500C
........................................................... 297
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
18.APPENDIX H – PRODUCT SPECIFICATION
18.1
KDC470
................................................................................................................................. 299
List of Figures
Figure 1 - How to turn on the power in KDC20/30/350/400/500
Figure 2 - Selecting a Bluetooth device type from the KDC menu
Figure 3 - Selecting Pairing mode in KDC
Figure 4 - Pairing mode button
Figure 5 - Pairing menu shortcut button in KDC500
Figure 6 - Finding Bluetooth MAC Address
Figure 7 - Connecting KDC with a smart phone by scanning Bluetooth MAC Address Barcode
Figure 8 - Location of KDC Menu and use of buttons (KDC100/200/250/300)
Figure 9 - Location and use of buttons on a keypad (KDC350)
Figure 10 - Location and use of buttons on a keypad (KDC500)
Figure 11 - KDC Display
Figure 12 - Scanning barcodes using KTSync
Figure 13 - Location for reading NFC Tag
Figure 14 - Delete Function in KDC20/30
Figure 15 - Replacing a Battery
Figure 16 - KTSync® Synchronizer Initial Screen
Figure 17 - File Menu
Figure 18 – Setting Menu
Figure 19 - Application Menu
Figure 20 - About Menu
Figure 21 - COM Port Selection for KDC
Figure 22 - Bluetooth Device Registry
Figure 23 – Configuration
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Figure 24 - KTSync Synchronization Settings
Figure 25 - Barcode & KDC Settings, Symbologies, Data Editing and Scan Options
Figure 26 - KTSync® Confirmation Settings
Figure 27 - KDC Menu in KTSync
Figure 28 - Mobile pKTSync
Figure 29 - Android aKTSync
Figure 30 - iPad/iPhone/iPod touch KTSync
Figure 31 - Blackberry bKTSync
Figure 32 - Application Menu
Figure 33 - Application Warning Window
Figure 34 - Application Generation Menu
Figure 35 - Data Filter Settings
Figure 36 - Master/Slave Application Settings
Figure 37 - Master/Slave Application Flow Chart
Figure 38 - Pick/BIN Application Menu
Figure 39 - Pick/BIN Application Flow Chart
Figure 40 - DB Lookup Application Menu
Figure 41 – Inventory Application
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
List of Tables
Table 1 - Features of KDC
Table 2 - Number of hours required to fully charge a KDC Battery
Table 3 - KDC Menu
Table 4 - KDC30/300/350C/420/450/500C Minimum Barcode Length
Table 5 - Explanation of LEDs
Table 6 - Troubleshooting Techniques
Table 7 - Symbologies Supported by KDC
Table 8 - Add-on for EAN-13 Symbology
Table 9 - Add-on for EAN-8 Symbology
Table 10 - Symbology Conversion
Table 11 - Verification of Optional "Check Digit"
Table 12 - Transmission of "Check Digit"
Table 13 - Resolution of Inconsistencies
Table 14 – Symbologies supported by KDC
-&%%%
Table 15 – Symbologies supported by KDC
Table 16 – Symbologies supported by KDC
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
COPYRIGHT, LICENSE, and WARNING PAGE
Copyright
2002-2016 by KOAMTAC, Inc. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or
mechanical means, without permission in writing from KOAMTAC, Inc. The material in this manual is
subject to change without notice. KOAMTAC reserves the right to make changes to any product to
improve reliability, function, or design. KOAMTAC does not assume any product liability arising out
of, or in connection with, the application or use of any product, circuit, or application described
herein. Follow all warnings and instructions marked on manual and units. Use only the power source
specified in this manual or marked on the units.
KDC® is a registered trademark and property of KOAMTAC, Inc.
KoamTac® is a registered trademark and property of KOAMTAC, Inc.
KTSync® is a registered trademark and property of KOAMTAC, Inc.
KoamTacON® is a registered trademark and property of KOAMTAC, Inc.
SmartSled® is a registered trademark and property of KOAMTAC, Inc.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO ANY TYPE OF MOISTURE. DO NOT LOOK
DIRECTLY INTO LASER OR POINT THE LASER INTO ANOTHER PERSON’S EYES. EXPOSURE TO THE BEAM MAY CAUSE
EYE DAMAGE.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
Patents:
Certain KDC Products may be covered by the following issued US patents numbers 7769917,
7954710, 8126399, 8295368, 8346979, 8347366, 8371506, 8483614, 8832323; Korea patents
numbers 10-1383407, 10-1354252 and may be patent pending elsewhere, UK publications
GB2492615, GB2514746; Korea publication 1020120128598.
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Regulatory Compliance
US
FCC ID: VH9KDC20, VH9KDC30, VH9KDC100, VH9KDC200, VH9KDC250, VH9KDC270, VH9KDC300,
VH9KDC350, VH9KDC350WA, VH9KDC400, VH9KDC450, VH9KDC470, VH9KDC500A
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and may
radiate radio frequency energy. It may cause harmful interference to radio communications if not
installed and used in accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which may be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference with one or more of the following
measures:
1. Reorient / Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a different circuit than the receiver.
4. Consult with the dealer or an experienced radio/TV technician for help.
WARNING:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
SAR (Specific Absorption Rate):
This product meets the applicable national or international RF exposure guidance (SAR guideline)
when used normally against your body or when worn or carried at a distance of 1 cm from the
body. While holding this barcode scanner with one’s hand and scanning the barcode with the
scanner facing the barcode, the scanned barcode data is transmitted to the server through CDMA
network based on the initially configured protocol (TCP, UDP, or HTTP). This use case guarantees
the minimum distance between the barcode scanner and the body for the SAR. The SAR guideline
includes a considerable safety margin designed to assure the safety of all persons, regardless of
age and health.
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Europe
2200 0983
Certificate No.: EMC15688-07-01
Products intended for sale within the European Union are marked with a CE Mark which indicates
compliance to applicable Directives and European Normes (EN), as follows. Amendments to these
Directives or ENs are included: Normes (EN), as follows.
Applicable Directives:
• Radio and Telecommunications Terminal Equipment Directive 1999/5/EC
Scope of Opinion
(Essential Requirements)
Applied Specifications/Standards TCF Identification
Results
Article 3.1(a) – Health
EN 62311:2008
Statement
Complies
Article 3.1(a) - Safety
EN 60950-1:2006+A11:2009
ESTCS1101-002
Complies
Article 3.1(b)
– EMC
EN 55022:2006+A1:2007
EN 55024:1998+A1:2001+A2:2003
ETSI EN 301 489
-1 V1.8.1 (2008-04)
ETSI EN 301 489-17 V2.1.1 (2009-05)
ESTCE
0712-007(1)
Complies
Article 3.2 – Radio
Spectrum Use
ETSI EN 300 328:V1.7.1 (2006
-10)
ESTR0801
-018(1)
Complies
Japan
003WWA080049, 003WWA090274, 208-120048, 208WW110041,
208-130029, 208-140011, 208-140049
Article 2-1-19, 2.4GHz Wide Band low power data communication system
Japan
2014026493, 2014027753
Korea
MSIP-CMM-A13-KDC20, MSIP-CMM-A13-KDC30, AI3-KDC100, AI3-KDC200,
MSIP-CMM-A13-KDC250, MSIP-CMM-A13-KDC350, MSIP-CMM-A13-KDC350, MSIP-CMM-A13-
KDC400, MSIP-CMM-A13-KDC450
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Laser Compliance
KDC20/100/200/250/270L/350L/410/411/415/470L
Complies with US 21 CFR 1040.10 and 1040.11 except for deviations
pursuant to laser notice no. 50, dated June 24, 2007 and IEC 60825-1 (Ed.
2.0)
Complies with IEC60825-1:1993 + A1:1997 + A2:2001
Battery Warning
x This device contains a rechargeable NiMH. Never throw the battery into a fire, as that could
cause the battery to explode.
x Never short-circuit the battery by bringing the terminals in contact with another metal
object. This could cause personal injury, a fire, and/or damage to the battery.
x Never dispose of used batteries with other ordinary solid wastes. Batteries contain toxic
substances.
x Dispose of used batteries in accordance with the prevailing community regulations that
apply to the disposal of batteries. Cover the metal terminals with insulating tape (this is to
prevent accidental short-circuiting).
x Never expose the battery to any liquid.
x Always keep the battery out of reach of infants or small children.
x Never shock the battery by dropping it or throwing it.
x Dispose of a spent or damaged battery promptly.
WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Product Disposal
This device should not be placed in municipal waste. Please check local regulations for disposal of
electronic products.
Bluetooth®
Core Specification: 2.1+EDR
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Apple®
Made for iPhone, Made for iPod, Made for iPad
Samsung®
Compatible with Galaxy Series
Warranty Policy
KOAMTAC ONE YEAR LIMITED WARRANTY
KOAMTAC products are warranted to be free from defects in materials or workmanship for one (1)
year from the date of purchase from an authorized dealer of KOAMTAC products. Within this period,
we will, at our sole discretion, repair or replace any components that fail in normal use. Such repairs
or replacement will be made at no charge to you for parts and/or labor, provided that you shall be
responsible for any transportation charges. Replacement products may be new or refurbished at
our discretion.
This warranty does not apply to: (i) cosmetic damage, such as scratches, nicks, stains and dents; (ii)
consumable parts, such as batteries, unless product damage has occurred due to a defect in
materials or workmanship; (iii) damage caused by accident, abuse, misuse, water (in excess of
specifications), flood, fire, or other acts of nature or external causes; (iv) damage caused by service
performed by anyone who is not an authorized service provider of KOAMTAC; or (v) damage to a
product that has been modified or altered without the prior written permission of KOAMTAC.
Repairs have a ninety (90) day warranty. If the unit sent in is still under its original warranty, then
the new warranty will be the longer of ninety (90) days or the balance of the original one year
warranty.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES EXPRESS, IMPLIED, OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR
OTHERWISE. Subject to applicable law, in no event shall our liability exceed the purchase price of the
Hardware.
RETURN
For warranty returns, you must pack your KOAMTAC product in its original packaging and include all
accessories and documentation. We reserve the right to charge for any damage to the KOAMTAC
product, and missing part fees may apply.
Please contact Customer Service prior to returning any product to receive a return authorization
form and RMA number. You will be responsible for, and pre-pay, all return shipping charges and
shall assume all risk of loss or damage to product while in transit to us. We recommend that you use
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
a traceable method of shipping for your protection. We will pay for shipping to return any product to
you.
Email us at rma@koamtac.com to obtain an RMA number. Once you have obtained the RMA
number, please send us your purchased KOAMTAC product with the RMA number clearly marked on
the outside of the package and on the shipping slip if you choose to use traceable carriers such as
UPS or FEDEX. Shipping fees for returns are your responsibility. Return shipping instructions and
return address will be included in your RMA document provided by KOAMTAC.
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1. Introduction
Congratulations on purchasing a revolutionary KOAMTAC KDC.
KOAMTAC’s KDC works with a wide variety of portable applications. Use it independently or as a PC,
PDA, or smartphone/tablet accessory. (*KDC350WA: KDC350WA follows KDC350 unless mentioned
explicitly)
FEATURES
KDC20
KDC30
KDC100
KDC200
KDC250
KDC270
KDC300
KDC350
*KDC350WA
KDC400
KDC450
KDC470
KDC500
USB
CONNECTIONS
1 1
2 1 1 1 1 1 1 2 2 1 1
RECHARGEABLE
BATTERY
YES
YES
YES
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
SCAN ENGINE
Laser/
CCD
Imager
Laser
Laser
Laser
Laser/
CCD/
Imager
Imager
Laser/
CCD/
Imager
CCD/
Imager
Laser/
Imager
Imager
Laser/
CCD/
Imager
CCD/
Imager
AUTOMATIC
DATA UPLOAD
YES
YES
YES
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
MAXIMUM
STORED BARCODE
(EAN13)
7,680
7,680
409,600
409,600
409,600
409,600
409,600
409,600
409,600
4,096
409,600
409,600
153,600
KTSync®
SOFTWARE
YES
YES
YES
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
SDK
YES
YES
YES
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
SUPPORTS
WINDOWS
XP, 7, 8 &
10
YES
YES
YES
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
ANDROID,
BLACKBERRY,
IOS, WINDOWS
PHONE 8.1 & 10
YES
YES
NO
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
BLUETOOTH
YES
YES
NO
YES
YES
YES
YES
YES
YES YES
YES
YES
YES
GPS
NO
NO
NO
NO
YES
NO
NO
YES
NO NO
NO
NO
NO
NFC
NO
NO
NO
NO
NO
NO
NO
YES
NO YES
NO
NO
YES
RFID
(HF) NO
NO
NO
NO
NO
NO
NO
NO
NO NO
YES
YES
NO
UHF
NO
NO
NO
NO
NO
NO
NO
NO
NO NO
YES
YES
NO
MSR
NO NO
NO
NO
NO
NO
NO
NO
NO YES
NO
NO
YES
ICCR
(IC CARD
READER)
NO NO
NO
NO
NO
NO
NO
NO
NO NO
NO
NO
YES
USB DISK
NO
NO
YES
YES
YES
YES
YES
YES
YES NO
NO
NO
NO
USB HID
YES
YES
YES
YES
YES
YES
YES
YES
YES NO
NO
NO
NO
WIFI
NO
NO
NO
NO
NO
NO
NO
YES
NO NO
NO
NO
NO
CDMA
NO
NO
NO
NO
NO
NO
NO
NO
YES NO
NO
NO
NO
Table 1 - Features of KDC
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1.1
KDC Package Contents
The standard KDC package contains:
1. One KDC
2. USB Cable
z KDC20/30 (N/A)
z KDC100/200/250/300/350 (8pin Ultra-mini USB Cable)
z KDC270/400/450/470/500 (5pin Micro USB Cable)
3. One Lanyard (KDC20/30/100/200/250/300/270/350) or One Hand Strap
(KDC400/450/470/500)
4. One KDC Protective Rubber Boot (KDC100/200/250/300).
The following KDC accessories are available to purchase at koamtac.com or by contacting a local
reseller.
z Protective Rubber Boots for KDC20/30/350.
z SmartSled® cases for KDC200/250/300/400/450/470.
z Charging Cradles for
KDC20/30/100/200/250/300/270/350/411/421/430/450/470/500
z Finger Trigger Gloves for KDC200/250/300/270/350
z Finger Trigger Glove Adaptor for KDC200/250/300/270/350
z KDC350/470/500 Hardpack Battery Charging Adaptor
z KDC500 SmartSled® Adaptor
z KDC Batteries
KDC400/450/470 SmartSled® cases and KDC500 SmartSled Adaptors are sold
separately. Depending on the distributor, package contents may vary.
0QVG
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
KDC20/30
Package Contents
KDC100/200/250/300
Package Contents
KDC270/KDC350
Package Contents
KDC400/450 /470
Package Contents
KDC500
Package Contents
KDC350WA
Package Contents
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1.2
KDC Characteristics
Before using the KDC, the user should become familiar with its physical characteristics. Refer to
Figure 2, 3, 4, and 5 below. These figures indicate the placement of the SCAN, UP, DOWN and
DELETE buttons, OLED display, LED, and ports on the KDC.
Although KDC models consist of similar buttons and LEDs, each model has different characteristics
for its own purpose of use. The KDC20/30/100 includes a swing-out USB connector and the
KDC350/500 has a keypad.
KDC20/30 Barcode Reader and Data Collector
Type A USB Swing Out
UP Button
Green/Red/Orange LEDs
SCAN Button
DELETE Button
DOWN Button
KDC20
KDC30
Green/Red/Orange LEDs
DELETE Button
UP Button
SCAN Button
DOWN Button
Type A USB Swing Out
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
KDC100 Barcode Reader and Data Collector
KDC200/250/300/270/350 Barcode Reader and Data Collector
Green/Red/Orange LEDs
OLED Display
SCAN Button
Ultra-mini USB Port
DOWN Button
UP Button
Green/Red/Orange LEDs
OLED Display
SCAN Button
Ultra-mini USB Port
DOWN Button
UP Button
Green/Red/Orange LEDs
Type A USB Swing Out
OLED Display
SCAN Button
Ultra-mini USB Port
DOWN Button
UP Button
KDC100
KDC200
KDC250/300
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
KDC400/450/470 Barcode Reader and Data Collector
UP Button
DOWN Button
SCAN Button
Ultra-mini USB Port
KDC350
Keypad
Shift%XWWRQ
Menu %XWWRQ
Green/Red/Orange LEDs
0RGH
%XWWRQ
Function Button
KDC2700
Ultra-mini USB Port
UP Button
OLED Display
Scan Button
DOWN Button
Green/Red/Orange LEDs
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
KDC500 Mobile POS
1D/2D Barcode Scanner
Left SCAN Button
Right SCAN Button
OLED Display
Secure Touch Keypad
ICCR (IC Card Reader)
Magnetic-Stripe
Card Reader
Micro USB
NFC Reader
Green/Red/Orange LEDs
KDC500
Micro USB Port
UP Button
Buzzer Hole
Scan Button
DOWN Button
Green/Red/Orange LEDs
KDC470
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1.3
Keypad Functionality for KDC350
Enables
the user to enter or exit the KDC Menu. While in menu
mode, press once to exit.
Enables
the user to chan
ge character input mode from capital letters
to small letters, and vice versa.
Enables
the user to switch between ABC and number input mode.
(UP button)
While in the KDC menu, press this button to go up on the selection
bar. While on the main screen, press this button and the KDC will try
to connect to a BT host device.
(DOWN button)
While in the KDC menu, press this button to go down on the
selection bar. While on the main screen, press this button to toggle
the iOS soft keyboard (if the KDC is
connected in HID-iOS mode).
(Number button)
Input numbers or characters
(Enter button)
Press to finish data input (if “Enter Key” option is disabled).
Press to finish data input and move cursor to next line (if “Enter Key”
option is enabled).
(Delete button)
Press to delete the last character or number input
+
(Power On/Off button)
Press both Scan button and Down button for more than
5
seconds at
the same time to turn
KDC350 power on and off.
(Function button)
This button may be used in
conjunction with a number key to control
the KDC settings shown below.
FN + 1
Keypad light On/Off
FN + 2
GPS Power On/Off (KDC350G series only)
FN + 3
NFC Power On/Off (KDC350N series only)
FN + 4
Enter Bluetooth Pairing Mode
FN + 5
Bluetooth Power On/Off
FN + 6
Change Bluetooth profile
FN + 0
Factory Default
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1.4
Keypad Functionality for KDC500
(Menu/Down button)
While in the KDC500 menu, press this button to scroll down the
selection bar. While on the main screen, press this but
ton for 5
seconds then the KDC500 will enter the KDC500 menu mode.
(FN/Up button)
While in the KDC500 menu, press this button to scroll up the
selection bar. While on the main screen, press this button for 5
seconds then the KDC500 will enter the KDC500
BT Service menu.
While the KDC500 waits for Alpha
-
Numeric key entry, this button
allows the user to switch between ABC and number input mode.
(Number button)
Input numbers or characters
(Enter button)
Press to finish data input.
(Delete button
)
Press to delete the last character or number input.
(Cancel button)
Press to cancel data input.
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1XP
B
6KLIW
$EF
B
6KLIW
$EF
.
$EF
.
$EF
.RDPWD
F
'R\RX
ZDQW
7
RFDQFHO"
<HV1R
$EF
.RDPWD
F
1.5
Input data by using a keypad (KDC350)
z When the KDC350 shows a blank main screen, you may start pressing numbers or characters
of the barcode data that needs to be input.
z See an example below: How to save the barcode data “123Koamtac”.
Cancel
Press the keys for
remaining letters.
Press 11@:/,22ABC and
3DEF
on the keypad.
Press MMode to switch to
Abc mode.
Press 55JKL on the
keypad
Press SShift on the
keypad to
change to
lower case mode.
Press MMenu and
select Yes
to cancel
input.
Press or
button
to save barcode
data.
n
to save
6&$1
Save
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
1.6
Turn on the power of KDC20/30/350/400/500
KDC20/30/270/350/400/470/500 have power on/off switch. Please turn on the power first before
using the device.
Press SCAN and DOWN
buttons simultaneously
for 5 seconds. The user
will hear a beep sound
when it is turned on.
6&$1%XWWRQ
'2:1%XWWRQ
Slide POWER button to
the right.
KDC4400
PSCAN
KDC220/30
Press SCAN and DOWN
buttons simultaneously
for 5 seconds. The user
will hear a beep sound
when it is turned on.
6&$1%XWWRQ
KDC2270
'2:1%XWWRQ
Press SCAN and DOWN
buttons simultaneously
for 5 seconds. The user
will hear a beep sound
when it is turned on.
PSCAN
KDC4470
'2:1%XWWRQ
6&$1%XWWRQ
MQCOVCEEQO
K
KDC User Manual
INTRODUCTION
Figure 1 - How to turn on the power in KDC20/30/350/400/500
KDC55000
Press Left and Right SCAN
buttons simultaneously for
5 seconds. The user will see
a KOAMTAC logo in the
display and hear a beep
sound when it is turned on.
/HIW6&$1
%XWWRQ
5LJKW
6&$1
%XWWRQ
K
KDC User Manual Installation
2. Installation
2.1
Bluetooth Pairing
The KDC may read and store barcode data independently, but it may also be used in conjunction with
a PC, PDA, or smart device.
In order to read barcode data with your KDC wirelessly, the user must first pair the KDC and smart
device via Bluetooth. If previously paired and no changes have been made in the smart device’s
Bluetooth settings, the smart device will always recognize the KDC that has previously been paired.
However, if changes have been made, the user may need to go through the pairing process again. The
user may also refer to Chapter 4. Bluetooth for more information about Bluetooth pairing.
Preparing for Pairing
Select a Bluetooth profile. There are two ways to set up a Bluetooth profile. The user may establish a
Bluetooth profile manually (on the scanner) or by scanning a programming barcode as shown below.
K
KDC User Manual Installation
KDC 20/100/200/250/270L/350L/410/411/415/470L/500L (1D)
Bluetooth Profile SPP Bluetooth Profile HID iOS Bluetooth Profile MFi
Bluetooth Profile SPP2.0 Bluetooth Profile HID normal
For PCI PTS compliance, KDC500L supports only Bluetooth Profile SPP
and MFi.
0QVG
K
KDC User Manual Installation
KDC30/300/270C/350C/420/421/425/450/470C/500C (2D)
Bluetooth Profile SPP Bluetooth Profile HID iOS
Bluetooth Profile MFi Bluetooth Profile SPP2.0
Bluetooth Profile HID normal
For PCI PTS compliance, KDC500C supports only Bluetooth Profile SPP and MFi.
Some KDCs are equipped with an LCD screen (KDC100/200/250/300/270/350/500), the user
may select a Bluetooth profile from the ConnectDevice menu as shown below.
KDC Menu BT Config Connect Device MFi Save & Exit
KD
C
M
e
n
u
n
n
ec
t D
e
vi
ce
BT Config
C
Co
n
Figure 2 - Selecting a Bluetooth device type from the KDC menu
MF
i
p
e
f
rom the KDC m
e
ve
&
Ex
i
t
Sav
enu
0QVG
K
KDC User Manual Installation
Pairing
First Option: Connect the KDC from a host (PC or Smart Device)
This method is recommended for first-time users or when the user is only connecting a few KDCs.
1. Put the KDC into Pairing mode
z Select the correct pairing barcode and scan below for your KDC model, or
KDC 20/100/200/250/270L/350L/410/411/415/470L/500L (1D)
KDC30/300/270C/350C/420/421/425/470C/500C (2D)
Pairing
z Select Pairing from the KDC menu.
From the KDC Menu Select BT Service Select Pairing
z Press the Scan button for three seconds in order to enter into Pairing mode.
Figure 3 - Selecting Pairing mode in KDC
Press SSCAN Button for 5 seconds
Figure 4 - Pairing mode button
F
r
o
m t
he
KDC M
e
n
u
lec
t
P
airin
g
elec
t BT
Se
rvi
ce
K
KDC User Manual Installation
Figure 5 - Pairing menu shortcut button in KDC500
z For the KDC500, press the FN button for five seconds in order to directly enter the BT Service
menu while it is not in the sleep mode.
Press FFN BButton for 5 seconds while
KDC500 is not the sleep mode
K
KDC User Manual Installation
2. On the host device, go to Settings -> Bluetooth, and select the KDC that needs to be paired. The
KDC and host device will now communicate with each other.
For PCI PTS compliance, KDC500 requires Numeric Comparison method.
3. After it has been installed, open KTSync and it will automatically find and connect to the KDC.
(Refer to 2.2 KOAMTAC Installation Wizard for more information about installing KTSync).
Second Option: Connect the host device from the KDC by scanning a Special Bluetooth MAC
Address barcode
Settings
Tap BBluetooth
Tap the KDC
0QVG
If the host device and KDC500 shows the same 6digit
number, press Pair/YES button on each device.
K
KDC User Manual Installation
This method is recommended for advanced users or when the application or process requires the
pairing of multiple KDCs to multiple host devices on a regular basis.
1. Find the Bluetooth MAC Address of the host device.
Tap on General Tap on About Bluetooth address
2. Create the Bluetooth MAC Address Barcode according to the format below as an example based
on “http://www.terryburton.co.uk/barcodewriter/generator/”.
For 1D scanners like KDC20/200/250/270L/350L/410/411/415/470L/500L,
Bluetooth MAC Address: 1234567890AB
Barcode Type (Symbology): Code 128
Contents: ^FNC3651234567890AB
Options: parsefnc
For 2D scanners like KDC30/300/270C/350C/420/421/425/450/470C/500C,
Bluetooth MAC Address: 1234567890AB
Barcode Type (Symbology): QR Code
Contents: ^022M^013KDC651234567890AB.
Options: eclevel=M parse
3. Print the Bluetooth MAC Address
Note:
2D barcode scanners such as the KDC30/300/350C/420/421/425/450/470C/500C models may
read barcodes that have been printed QR barcodes that are on a LCD screen.
1D CCD barcode scanners may read barcodes that have been printed barcodes that are on a
LCD screen.
1D laser barcode scanners such as the
KDC20/100/200/250/270L/350L/410/411/415/470L/500L models are not designed to read
barcodes from a LCD screen and will only read printed barcodes.
Settings
Figure 6 - Finding Bluetooth MAC Address
K
KDC User Manual Installation
4. Connect the KDC to the host device by scanning the Bluetooth MAC Address Barcode.
5. Open KTSync after it has been installed, and it will automatically find the KDC and connect. (Refer
to 2.2 KOAMTAC Installation Wizard for more information about installing KTSync)
Tap on BBluetooth
Scan the BT MAC Address
Barcode
t
h
B
T
M
A
C
A
d
Tap on PPair
Complete!
Settings
Figure 7 - Connecting KDC with a smart phone by scanning Bluetooth MAC Address Barcode
K
KDC User Manual Installation
2.2
KOAMTAC Installation Wizard
Windows 7, 8 & 10
WARNING: DO NOT CONNECT KDC TO USB PORT PRIOR TO DRIVER INSTALLATION
1. Insert KOAMTAC Installation CD into the computer’s CD drive.
2. Click Start icon then My Computer icon. A list of devices on the computer will be
displayed, including the disk drive containing the KOAMTAC Installation CD.
3. Click on the KOAMTAC Installation CD icon, then the Setup directory. Click on the
PC_Setup.exe file, which will execute the KTSync Setup Wizard.
x If the KTSync Setup Wizard locates an older version of KTSync on the computer, the
user will be prompted to remove the older program before installing the new version.
Select Remove KTSync then click Finish. When removal is complete, click Close. Go to
Step 2 to run KTSync Setup Wizard.
KTSync Setup Wizard
To install KTSync, follow the steps shown in the images below.
1. In the KTSync Setup Wizard window, click Next.
2. In the License Agreement window, select “I Agree” and click Next.
0QVG
K
KDC User Manual Installation
3. In the KTSync Installation Complete window, click Close and wait for the Device Driver Installation
Wizard.
4. In the Windows Security window, click Install to complete installation.
Connect KDC to Computer
Using the USB cable included with the KDC or built-in swing out USB connector, follow the directions
below.
1. Connect KDC to PC.
2. Wait until the computer beeps and/or displays the message Found New Hardware.
K
KDC User Manual Installation
Verify COM Port Address
z The installed COM Port may be verified in Device Manager.
Android
z
Download and install KTSync from the Android Play Store.
https://play.google.com/store/apps/details?id=com.koamtac.ktsync&hl
z
BlackberryDownload and install KTSync from the Blackberry App World.
http://appworld.blackberry.com/webstore/content/16861?lang=en
iPad/iPhone/iPod Touch
z
Download and install KTSync from the Apple App Store.
http://itunes.apple.com/us/app/ktsync/id372916602?mt=8
K
KDC User YOUR KDC
3. Operating your KDC
3.1
Getting Started
Attaching a Lanyard or Hand Strap to a KDC
To prevent possible damage to the KDC, we STRONGLY recommend wearing it around the neck or
hand, using the included lanyard or hand strap. In addition, the user should not swing the KDC by
its lanyard or hand strap. Impact with another object may cause the KDC to malfunction or
damage.
To attach a lanyard/hand strap:
KDC20/30
KDC100/200/300/270/350/400
KDC500
Fit the thin
end of the
lanyard
through the
pillar of the
KDC.
Guide the
thick end of
strap
through the
thin loop.
Pull the
strap tight to
secure.
K
KDC User YOUR KDC
Charge KDC Battery
Prior to using the KDC, the user should charge the battery. Follow the instructions below.
1. Connect the KDC cable to the mini USB connector on the KDC.
2. Connect the KDC cable to the Type A USB connector on the computer.
3. The KDC battery will begin charging. Within a few minutes, the two small LEDs (three LEDs in
case of KDC500) on the front panel will illuminate orange. When the battery is fully charged,
the LEDs will illuminate green.
Configure KDC
The KDC is designed to meet the data collection requirements of many different industries in a
variety of dynamic situations. To deliver the best performance in these diverse environments, the
KDC is designed to be configured quickly and easily.
However, to perform at its optimum level, the KDC must be configured properly. Until the user is
familiar with the KDC configuration settings, it is recommended that the user DOES NOT modify the
KDC settings. The KDC may be configured by using three different methods, which are explained in
Section 3.3 – KDC Menus, Chapter 5 –Synchronization, and Appendix C/D – Special Barcodes.
CONFIGURATION METHODS FOR THE KDC100/200/250/300/270/350/500
z KDC Menu
z KTSync Software
z Special Barcodes
Figure 8 - Location of KDC Menu and use of buttons (KDC100/200/250/300/270)
KDC100 KDC20/200
KDC30/250/300/270
KDC350 KDC400
KDC500
2 Hours 2 Hours 4 Hours 5 Hours 5 Hours
5 Hours
Table 2 - Number of hours required to fully charge a KDC Battery
Select one of the
menus by pressing
the S
Scan Button
.
Press the UUp and DOWN
Buttons
simultaneously to
access the KDC menu.
Move the menu bar up and
down
by pressing Up and
Down Buttons.
K
KDC User YOUR KDC
CONFIGURATION METHODS FOR KDC20/30/400
z KTSync Software
z Special Barcodes
Press the Button to access the KDC menu.
Move the menu bar up and down by pressing the
and Buttons, and configure the KDC by
pressing the SCAN Button to select a menu.
Figure 9 - Location and use of buttons on a keypad (KDC350)
Press the Button for 5 seconds to access the
KDC menu. Move the menu bar up and down by
pressing the and Buttons, and configure
the KDC by pressing the SCAN Button to select a menu.
Figure 10 - Location and use of buttons on a keypad (KDC500)
K
KDC User YOUR KDC
3.2
Basics
Reading Barcodes
To read a barcode using the KDC, simply point the KDC at a barcode and press the scan button. Be
sure to point the scan engine window at the barcode, not at the user’s face, and make sure to
position the light beam on the barcode.
If a barcode has been successfully scanned, the user will hear one short beep and the LEDs will
illuminate green. The scanned barcode data will be displayed on the KDC screen, along with the scan
time and battery level. Depending on the configuration of the KDC, other information may also be
displayed.
Figure 12 - Scanning barcodes using KTSync
If scanning was unsuccessful, the user will hear two short beeps, the LEDs will illuminate red, and the
message Failed reading will display. If this is the case, the user should point the KDC at the barcode
and press the scan button while trying the following suggestions:
Figure 11 - KDC Display
K
KDC User YOUR KDC
z
Modify the angle of the KDC in relation to the barcode, making the angle more wide or
narrow as needed. (Laser Model)
z
Modify the distance between the barcode and the KDC, moving closer or further away as
needed.
z
Check the option settings defined in the KDC menu section and change options as needed.
z
Check to see that the barcode’s width does not exceed the light beam’s width, and vice
versa.
Read Barcodes with GPS Coordinates (KDC250G/350G)
The KDC350G may add GPS coordinates after the barcode data. To do so, the user may follow the
below instructions.
Because of the characteristics of GPS, this function is only available when outdoors.
1. Go to GPS Power in GPS Menu and select Enable.
2. Check to see if the KDC is successfully acquiring GPS data by selecting Acquire Test in GPS
Menu.
When the user selects the Acquire Test, an ‘Acquiring’ message will appear on the screen. If
this is the first test, check to make sure the ‘Acquired’ message appears within 90 seconds
of acquiring GPS signal.
3. Go to SystemConfig in the KDC Menu and select GPS data in Display Format.
4. After finishing the configuration, scan a barcode as explained in 3.2.1 Reading Barcodes.
When the user has successfully scanned a barcode, the barcode data and GPS coordinate
will appear on the KDC screen.
For more information, refer to 3.3 Menu - GPS Config (KDC250G/350G).
Reading NFC Tags (KDC350N/400N/KDC500)
1. Enable the NFC Power option in the NFC Config menu.
2. Touch the NFC tag to the back of the KDC350N/400N case (or NFC logo on the front of the
KDC500 case), and make sure the tag and case are within 5cm of each other.
0QVG
K
KDC User YOUR KDC
Figure 13 - Location for reading NFC Tag
3. The KDC will show the NFC tag UID and the user will hear a short beep if it has been read
successfully.
Reading HF RFID Tags (KDC450/470)
The KDC450/470 may virtually read any ISO/IEC 14443 A or B compliant smartcards, or ISO/IEC
15693 compliant HF RFID tags.
To read a HF RFID tag, touch the RFID card to the back of the KDC450/470 case, and make sure the
tag and case are within 5cm of each other. The user will hear a short beep if it has been read
successfully.
Inputting Data by Using a Keypad (KDC350)
The KDC350 Enables users to input barcode data by using its keypad. The user may switch between
Num mode and Abc mode by using the Mode button.
To switch between uppercase and lowercase letters, the user may press the Shift button while in
Abc mode. To save the data input, press the Enter or SCAN button. For data input, press the Menu
button. Refer to 1.5 Input data by using a keypad (KDC350) for more detailed information about the
process.
Read Magnetic-Stripe (MS) Card(KDC500)
1. The paired host application sends a command to enable the MS Card Reader.
2. Swipe MS Card either top to bottom or bottom to top. Make sure the magnetic stripe of the card
face to the KDC500.
3. The KDC500 will send the MS card data to the paired host application and the user will hear a
short beep if it has been read successfully.
K
KDC User YOUR KDC
Read Integrated Chip (IC) Card(KDC500)
1. The paired host application sends a command to enable the IC Card Reader.
2. Insert IC Card into the IC Card slot located in the left side of KDC500. Make sure the IC of the card
face to up.
3. The KDC500 will send the IC card data read to the paired host application.
Synchronizing data to the host device
Use the KTSync program to synchronize barcode data from the KDC to the host device. Please refer to
Chapter 5. Synchronization for details.
K
KDC User YOUR KDC
3.3
KDC Menu
Top Menu
Sub Menu
Options
KDC20
KDC30
KDC100
KDC200
KDC250
KDC300
KDC270L
KDC350L
KDC350C
KDC Mode
Normal
Default
Default
Default
Default
Default
Default
Default
Default
Default
Application
N/A
N/A
Custom
Application
Custom
Application
Custom
Application
Custom
Application
Custom
Application
Custom
Application
Custom
Application
View Data
View/Delete
N/A
N/A
View/Delete
Data
View/Delete
Data
View/Delete
Data
View/Delete
Data
View/Delete
Data
View/Delete
Data
View/Delete
Data
Set Barcodes
(20//100/
200/250
/270L
/
/350L)
EAN13
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
EAN8
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
UPCA
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
UPCE
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
CODE39
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
ITF14
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
CODE128
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
I2of5
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
CODABAR
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
GS1-128
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
CODE93
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
CODE35
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
BooklandEAN
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
EAN13withAddon
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
EAN8withAddon
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
UPCAwithAddon
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
UPCEwithAddon
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
GS1 Omni
Enable/
Disable
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
GS1 Limited
Enable/
Disable
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
GS1 Expanded
Enable/
Disable
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Set Barcodes
(30/300
/270C
/ 350C)
1D Symbology
Codabar
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code 11
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code 32
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code 39
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code 93
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code 128
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
EAN-8
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
EAN-13
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
GS1 Composit
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
I2of5
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Matrix 2of5
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
MSI
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Plessey
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
PosiCode
N/A
Enable
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
GS1 Omni
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
GS1 Limited
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
GS1 Expanded
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
S2of5 Ind
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
S2of5 IATA
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
TLC39
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Telepen
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Trioptic
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
UPCA
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
UPCE0
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
UPCE1
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
2D Symbology
AztecCode
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
AztecRunes
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
CodablockF
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code16K
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code49
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
DataMatrix
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
K
KDC User YOUR KDC
MaxiCode
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
MicroPDF
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
PDF417
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
QRCode
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
HanXin Code
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Postal Codes
Postnet
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
PlanetCode
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
UK Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Mayada Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Kix Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Australia Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Japan Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
China Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Korea Post
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
OCR
OCR Off
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
OCR A
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
OCR B
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
OCR
Passport
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
OCR MICR
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
OCR SEMI
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Barcode
Options
(20/100
/200/250
/270
L/
/350L)
CodaBar_NoStartSt
opChars
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
UPCE_as_UPCA
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
EAN8_as_EAN13
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
UPCE_as_EAN13
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
ReturnCheckDigit
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
VerifyCheckDigit
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
UPCA_as_EAN13
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
I2of5_VerifyCheckD
igit
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Code39_VerifyChec
kDigit
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
I2of5_ReturnCheck
Digit
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Code39_ReturnChe
ckDigit
Enabled/
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
UPCE_ReturnCheck
Digit
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
UPCA_ReturnCheck
Digit
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
EAN8_ReturnCheck
Digit
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
EAN13_ReturnChec
kDigit
Enabled/
Disabled
Enabled
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Barcode
Options
(30/300
/270C
/350C)
Codabar
Tx StartStop
(Enabled/
Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Check Digit
(DoNotVerify/
VerfyDONotT
X/VerifyDoTx)
N/A
DoNotVerify
N/A
N/A
N/A
DoNotVerify
N/A
N/A
DoNotVerify
Concatenate(
Disabled/Enab
led/Required)
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Code39
Tx StartStop
(Enabled/
Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Check
Digit(DoNotVe
rify/VerfyDON
otTX/VerifyDo
Tx)
N/A
DoNotVerify
N/A
N/A
N/A
DoNotVerify
N/A
N/A
DoNotVerify
Append
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Full
ASCII(Enabled
/Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
I2of5
Check Digit
(DoNotVerify/
VerfyDONotT
X/VerifyDoTx)
N/A
DoNotVerify
N/A
N/A
N/A
DoNotVerify
N/A
N/A
DoNotVerify
Code11
Check Digit
(2 digits/1
digit)
N/A
2 digits
N/A
N/A
N/A
2 digits
N/A
N/A
2 digits
Code128
Concatenate(
Disabled/Enab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Telepen
Output(Origin
al/AIM)
N/A
Always AIM
N/A
N/A
N/A
AIM
N/A
N/A
AIM
UPCA
VerifyChkDgt(
Enabled/Disab
led)
N/A
Always
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
NumberSys(E
nabled/
Disabled)
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
2DgtAddenda(
Enabled/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
K
KDC User YOUR KDC
5DgtAddenda(
Enabled/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Coupon Code
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
UPCE
Expand
(Enabled/
Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
Check Digit
(Enabled/
Disabled)
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
NumberSys(E
nabled/
Disabled)
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
2DgtAddenda(
Enabled/Di
sab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
5DgtAddenda(
Enabled/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
EAN-13
EAN-8
VerifyChkDgt(
Enabled/Disab
led)
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
2DgtAddenda(
Enab
led/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
5DgtAddenda(
Enabled/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
ISBN Trans.
(Enabled/
Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
VerifyChkDgt(
Enabled/Disab
led)
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
2DgtAddenda(
Enabled/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
5DgtAddenda(
Enabled/Disab
led)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
Enabled
N/A
N/A
N/A
Enabled
N/A
N/A
Enabled
MSI
Tx CheckChar
(Enabled/
Disabled)
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
PosiCode
A and B/A&B
LimitedA/A&B
LimitedB
N/A
N/A
N/A
N/A
N/A
A&B
LimitedB
N/A
N/A
A&B
LimitedB
GS1
UPCEAN
Ver.
(Enabled/
Disabled)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
GS1
Emulation
(No Emulate/
GS1 128
Emul/GS1
Emulate)
N/A
N/A
N/A
N/A
N/A
No Emulate
N/A
N/A
No Emulate
PostNet
Tx
CheckChar(En
abled/Disable
d)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
PlanetCode
Tx
CheckChar(En
abled/Disable
d)
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Scan Options
Scan Angle
Narrow/
Wide
Wide
(Laser only)
N/A
Wide
Wide
Wide
N/A
Wide
(Opticon
Laser only)
Wide
(Opticon Laser
only)
N/A
Filter
Normal/
High
Normal
(Laser only)
N/A
Normal
Normal
Normal
N/A
Normal
(Opticon
Laser only)
Normal
(Opticon Laser
only)
N/A
Time Out
.5 seconds to
10 seconds
2 second(s)
2 second(s)
2 second(s)
2 second(s)
2 second(s)
2 second(s)
2 second(s)
2 second(s)
2 second(s)
Min. Barcode
Length
2 to 36
characters
4 chars
N/A
4 chars
4 chars
4 chars
N/A
4 chars
4 chars
N/A
Min. Barcode
Length
2 to 48
characters
N/A
N/A
N/A
N/A
N/A
4 chars
N/A
N/A
4 chars
Security Level
1 to 4 level
2 level
N/A
2 level
2 level
2 level
N/A
2 level
2 level
N/A
Image Capture
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Auto Trigger
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Reread Delay
Continuous,
Short,
Medium,
Medium
Medium
Medium
Medium
Medium
Medium
Medium
Medium
Medium
K
KDC User YOUR KDC
Long, Extra
Long
Finger Trigger
Enabled/Disab
led
N/A
N/A
Enabled
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Partial Display
Start Position
1
1
1
1
1
1
1
1
1
No. of Char(s)
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
Action
Select
Select
Select
Select
Select
Select
Select
Select
Select
Data Process
Wedge / Store
Wedge Only
Wedge &
Store Always
Default
Default
Default
Default
Default
Default
Default
Default
Default
Store Only
Save if Sent
Save if Not
Sent
Data Format
Barcode only
Default
Default
Default
Default
Default
Default
Default
Default
Default
Packet Data
Data Editor/
Prefix
Data Editor/ Suffix
Data Editor/ AIM ID
None/In
Prefix/In
Suffix
None
None
None
None
None
None
None
None
None
Data Editor/ Partial
Data
Start Position
1
1
1
1
1
1
1
1
1
No. of Char(s)
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
0 chars
Action
Select
Select
Select
Select
Select
Select
Select
Select
Select
Handshake
Enable/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Terminator
None, CR, LF,
CR+LF, Tab,
Right Arrow,
Left
Arrow,Down
Arrow, Up
Arrow
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
Chk Duplicate
Enabled/Disab
led
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enter Key
Enabled/Disab
led
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Disabled
Extend Key
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Disabled
Age Verify
Verification
Enabled/
Disabled
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Age Default
N/A
21
N/A
N/A
N/A
21
N/A
N/A
21
BT Config
Connect Device
(Non Mfi mode)
SPP
Default
Default
N/A
Default
Default
Default
Default
Default
Default
HID iOS
N/A
SPP2.0
N/A
HID normal
N/A
Connect Device
(Mfi mode )
SPP
N/A
MFi
Default
Default
N/A
Default
Default
Default
Default
Default
Default
Auto Connect
Enabled
/Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Reconnect
Enabled/
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power On
Enabled/
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power
On/Power On Time
disabled, 1sec
to
10second(s)
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power Off
Enabled/
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power
Off/Beep Warning
Enabled/
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power
Off/Power Off Time
1 to 30
minutes
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
PowerOff Msg
Enabled/Disab
led
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
MAC Address
12 Characters
Bluetooth
MAC Address
N/A
BT FW Version
v1.2.xrt
Bluetooth
Firmware
Version
N/A
Wakeup Nulls
Enabled/Disab
led
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Connect Alert
Enabled/Disab
led
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
BT Toggle
Enabled/Disab
led
Enabled
Enabled
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
DisconnectBtn
Enabled/Disab
led
Enabled
Enabled
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
HID AutoLock
disabled,1,2,3,
4,5,10,15
minutes
1 minutes
1 minutes
N/A
1 minutes
1 minutes
1 minutes
1 minutes
1 minutes
1 minutes
HID Keyboard
US,German,Fr
ench ,Ita
lian,Spanish
US
US
N/A
US
US
US
US
US
US
HID Delay/Initial
Disabled,
1,2,3,5,10
secs
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
HID Delay/Inter
char
Disabled,10,
20, 30, 50,
100msec
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
K
KDC User YOUR KDC
HID Ctrl Char
Disabled,
Alt+Numpad,
^+Character,
Replace to |
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
BT Service
Power
Enabled/
Disabled
Enabled
Enabled
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Pairing
Pairing
neighboring
Bluetooth
devices
N/A
Discovering
Discovering
neighboring
Bluetooth
devices
N/A
Connecting to
View Connect
to Bluetooth
device
N/A
HID Sync
N/A
Auto Pairing
Enabled/Disab
led
Enabled
Enabled
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
USB Config-
USB Serial
Mode
(M model)
USB Mode
USB
Serial/USB
Disk/USB HID
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Config-
USB Disk
Mode
(M model)
USB Mode
USB
Serial/USB
Disk/USB HID
N/A
N/A
USB Disk
USB Disk
USB Disk
USB Disk
USB Disk
USB Disk
USB Disk
Disk Format
Format KDC
USB Disk
N/A
N/A
Data Format
Data,DataTim
e,
DataType,Dat
aTimeType
N/A
N/A
Data
Data
Data
Data
Data
Data
Data
USB Config-
USB HID
(M model)
USB Mode
USB
Serial/USB
Disk/USB HID
USB HID
USB HID
USB HID
USB HID
USB HID
USB HID
USB HID
USB HID
USB HID
NFC Config
(N model)
NFC Power
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Data Format
Barcode
only/Packet
Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Packet Data
Packet Data
UID Only
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
GPS Config
(G model)
GPS Power
Disabled
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Disabled
Power Mode
Normal/Powe
r Save
N/A
N/A
N/A
N/A
Normal
N/A
N/A
Normal
Normal
Bypass Data
Enabled/
Disabled
N/A
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Disabled
Acqurie Test
N/A
N/A
N/A
N/A
N/A
N/A
Reset GPS
N/A
N/A
N/A
N/A
N/A
N/A
System
Config
Memory Size(3.0+
only)
0.5/6.5, 1/6,
2/5, 3/4,
4/3,
5/2, 6/1, 70
N/A
N/A
0.5M/6.5M
0.5M/6.5M
0.5M/6.5M
0.5M/6.5M
0.5M/6.5M
0.5M/6.5M
0.5M/6.5M
Memory Status
No. of Stored
Barcodes
Free Memory
Available
Reset Memory
Memory
(Empties
Data)
Application
Memory
BT Registry
(KDC100 Not
use)
Auto Erase
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Sleep Timeout
Disabled, 1sec
to
10minute(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
Date / Time
YYYY:MM:DD
& HH:MM:SS
Battery
% of Battery
Charge
Available
Version
Firmware
Version &
Serial No.
Button Lock
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Beep Alert
/Beep Sound
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert /Power
On Beep
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert /Beep
On Connect
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert /Beep
On Scan
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Volume
Low/High
Low
Low
Low
Low
Low
Low
Low
Low
Low
Mfi
( i-chip installed)
Enabled/Disab
led
Enabled
Enabled
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Vibrator
Enabled/
Disabled/
Config
Disabled
Disabled
N/A
N/A
N/A
N/A
Disabled
Disabled
Disabled
Auto Exit
Enabled/
Disabled
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Port Status
Enabled/
Disabled
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Display Format
Time &
Battery / Type
& Time / Type
& Battery /
Memory
Status / GPS
Data(KDC250
only)/Barcode
Only/
N/A
N/A
Time &
Battery
Time &
Battery
Time &
Battery
Time &
Battery
Time &
Battery
Time & Battery
Time &
Battery
K
KDC User YOUR KDC
Graphic
Menu Barcode
Enabled/
Disabled
N/A
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
Disabled
Scrolling
Enabled/
Disabled
N/A
N/A
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Brightness
1 to 15 level(8
level)
N/A
N/A
8 level
8 level
8 level
8 level
8 level
8 level
8 level
Keypad
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Enabled
Language
(FW Version 3.x
only)
None/
US(English)/
French/
Italian/
Spanish/
Korean/
Japanese
N/A
N/A
None
None
None
None
None
None
None
Factory Default
Restores
Default
Settings
MSR Config
Data Format
MSR Data
Only
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Packet Data
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Use Track1
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Use Track2
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
UseTrack3
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Beep on error
reading
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Encrypt MSR Data
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
AES Key Length
128bit/192bit
/256bit
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Card Type
ISO/OTHER
1/AAMVA
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Track Separator
None/Space/C
omma/Semico
lon/CR/LF/CR
&LF/Tab
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Attach Start/End
Sentinel
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Partial Data Start
Position
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Partial Data Length
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Partial Data Action
Erase/
Select
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
WIFI Config
Power
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enable
Enable
AP
SSID
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Empty
Empty
Passcode
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Empty
Empty
Server
IP Address
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0.0.0.0
0.0.0.0
Server
URL Address
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Empty
Empty
Server
Port Number
N/A
N/A
N/A
N/A
N/A
N/A
N/A
80
80
Server >
Protocol
UDP/TCP/
HTTP GET/
HTTP Post
N/A
N/A
N/A
N/A
N/A
N/A
N/A
HTTP Post
HTTP Post
Server > SSL
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Server
Server Page
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Empty
Empty
Resp. Timeout
1/2/3/4/5/6/7
/8/9/10 sec
N/A
N/A
N/A
N/A
N/A
N/A
N/A
10 sec
10 sec
Connect
Connecting to
AP
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Auto Connect
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Send Stored
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Version
APP
MAC
N/A
N/A
N/A
N/A
N/A
N/A
N/A
K
KDC User YOUR KDC
Top Menu
Sub Menu
Options
KDC410/411
KDC415
KDC420/421
KDC425
KDC430
KDC450
KDC470C
KDC500L
KDC500C
KDC Mode
Normal
Default
Default
Default
Default
Default
Default
Default
N/A
N/A
Application
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
View Data
View/Delete
N/A
N/A
N/A
N/A
N/A
N/A
N/A
View/Delete
Data
View/Delete
Data
Set Barcodes
(410/
411/415/
4
70L/500L)
EAN13
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
EAN8
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
UPCA
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
UPCE
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
CODE39
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
ITF14
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
CODE128
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
I2of5
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
CODABAR
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
GS1-128
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
CODE93
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
CODE35
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
BooklandEAN
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
EAN13withAddo
n
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
EAN8withAddon
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
UPCAwithAddon
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
UPCEwithAddon
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
Set Barcodes
(420/
421/
425/4
50/470C/
500C)
1D Symbology
Codabar
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code 11
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code 32
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code 39
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code 93
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code 128
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
EAN-8
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
EAN-13
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
GS1 Composit
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
I2of5
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Matrix 2of5
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
MSI
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Plessey
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
PosiCode
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
GS1 Omni
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
GS1 Limited
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
GS1 Expanded
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
S2of5 Ind
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
S2of5 IATA
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
TLC39
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Telepen
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Trioptic
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
UPCA
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
UPCE0
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
UPCE1
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
2D Symbology
AztecCode
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
AztecRunes
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
CodablockF
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code16K
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code49
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
DataMatrix
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
MaxiCode
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
MicroPDF
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
PDF417
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
QRCode
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
HanXin Code
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Postal Codes
Postnet
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
PlanetCode
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
UK Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
K
KDC User YOUR KDC
Mayada Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Kix Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Australia Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Japan Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
China Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Korea Post
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
OCR
OCR Off
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
OCR A
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
OCR B
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
OCR USC
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
OCR MICR
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
OCR SEMI
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Barcode
Options
(410
/411/415/
4
70L/500L)
CodaBar_NoStar
tStopChars
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
UPCE_as_UPCA
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
EAN8_as_EAN1
3
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
UPCE_as_EAN13
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
ReturnCheckDigi
t
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
VerifyCheckDigit
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
UPCA_as_EAN1
3
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
I2of5_VerifyChe
ckDigit
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
Code39_VerifyC
heckDigit
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
I2of5_ReturnCh
eckDigit
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
Code39_Return
CheckDigit
Enabled/
Disabled
Disabled
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
N/A
UPCE_ReturnCh
eckDigit
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
UPCA_ReturnCh
eckDigit
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
EAN8_ReturnCh
eckDigit
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
EAN13_ReturnC
heckDigit
Enabled/
Disabled
Enabled
Enabled
N/A
N/A
N/A
N/A
N/A
Enabled
N/A
Barcode
Options
(KDC420/425/4
50/470C/
500C)
Codabar
Tx StartStop
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Check Digit
(DoNotVerify/Ve
rfyDONotTX/Ver
ifyDoTx)
N/A
N/A
DoNotVerify
DoNotVerify
N/A
DoNotVerify
DoNotVerify
N/A
DoNotVerify
Concatenate(Dis
abled/Enabled/
Required)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Code39
Tx StartStop
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Check
Digit(DoNotVerif
y/VerfyDONotTX
/VerifyDoTx)
N/A
N/A
DoNotVerify
DoNotVerify
N/A
DoNotVerify
DoNotVerify
N/A
DoNotVerify
Append
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Full
ASCII(Enabled/D
isabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
I2of5
Check Digit
(DoNotVerify/Ve
rfyDONotTX/Ver
ifyDoTx)
N/A
N/A
DoNotVerify
DoNotVerify
N/A
DoNotVerify
DoNotVerify
N/A
DoNotVerify
Code11
Check Digit
(2 digits/1 digit)
N/A
N/A
2 digits
2 digits
N/A
2 digits
2 digits
N/A
2 digits
Code128
Concatenate(Dis
abled/Enabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Telepen
Output(Original/
AIM)
N/A
N/A
AIM
AIM
N/A
AIM
AIM
N/A
AIM
UPCA
VerifyChkDgt(En
abled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
NumberSys(Ena
bled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
2DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
5DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Coupon Code
(Enabled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
UPCE
Expand
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
K
KDC User YOUR KDC
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
Check Digit
(Enabled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
NumberSys(Ena
bled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
2DgtAddenda(E
na
bled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
5DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
EAN-13
VerifyChkDgt(En
abled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
2DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
5DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
ISBN Trans.
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
EAN-8
VerifyChkDgt(En
abled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
2DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
5DgtAddenda(E
nabled/Disabled
)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Req. Addenda
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Sep. Addenda
(Enabled/
Disabled)
N/A
N/A
Enabled
Enabled
N/A
Enabled
Enabled
N/A
Enabled
MSI
Tx CheckChar
(Enabled/
Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
PosiCode
A and B/A&B
LimitedA/A&B
LimitedB
N/A
N/A
A&B
LimitedB
A&B
LimitedB
N/A
A&B
LimitedB
A&B
LimitedB
N/A
A&B
LimitedB
GS1
UPCEAN
Ver.(Enabled/Di
sabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
GS1 Emulation
(No Emulate/
GS1 128
Emul/GS1
Emulate)
N/A
N/A
No Emulate
No Emulate
N/A
No Emulate
No Emulate
N/A
No Emulate
PostNet
Tx
CheckChar(Enab
led/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
PlanetCode
Tx
CheckChar(Ena
b
led/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
Disabled
Scan Options
Power
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Scan Angle
Narrow/
Wide
Wide
Wide
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Filter
Normal/
High
Normal
Normal
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Time Out
.5 seconds to 10
seconds
2 second(s)
2 second(s)
2 second(s)
2 second(s)
N/A
2 second(s)
2 second(s)
2 second(s)
2 second(s)
Min. Barcode
Length
2 to 36
characters
4 chars
4 chars
N/A
N/A
N/A
N/A
N/A
4 chars
N/A
Min. Barcode
Length
2 to 48
characters
N/A
N/A
4 chars
4 chars
N/A
4 chars
4 chars
N/A
4 chars
Security Level
1 to 4 level
2 level
2 level
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Image Capture
Enabled/
Disabled
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
N/A
Auto Trigger
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Reread Delay
Continuous,
Short, Medium,
Long, Extra Long
Medium
Medium
Medium
Medium
N/A
Medium
Medium
Medium
Medium
Finger Trigger
Enabled/Disable
d
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Partial Display
Start Position
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1
1
No. of Char(s)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0 chars
0 chars
Action
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Select
Select
Data Process
Wedge / Store
Wedge Only
Wedge & Store
Always
Default
Default
Default
Default
Default
Default
Default
Default
Default
Store Only
Save if Sent
Save if Not Sent
Data Format
Barcode only
Default
Default
Default
Default
N/A
Default
Default
Packet Data
Default
Default
Data
Editor/Prefix
Data
Editor/Suffix
K
KDC User YOUR KDC
Data Editor/AIM
ID
None/In
Prefix/In Suffix
None
None
None
None
N/A
None
None
None
None
Data
Editor/Partial
Data
Start Position
1
1
1
1
N/A
1
1
1
1
No. of Char(s)
0 chars
0 chars
0 chars
0 chars
N/A
0 chars
0 chars
0 chars
0 chars
Action
Select
Select
Select
Select
N/A
Select
Select
Select
Select
Handshake
Enable/
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
N/A
N/A
Terminator
None, CR, LF,
CR+LF, Tab,
Right Arrow,
Left
Arrow,Down
Arrow, Up
Arrow
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
Chk Duplicate
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Enter Key
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Extend Key
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Age Verify
Verification
Enabled/
Disabled
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
N/A
N/A
Age Default
N/A
N/A
21
21
N/A
21
21
N/A
N/A
BT Config
Auto SPP/MFi
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
ConnectDevice
(Non Mfi mode)
SPP
Default
Default
Default
Default
Default
Default
Default
N/A
N/A
HID iOS
N/A
N/A
SPP2.0
N/A
N/A
HID normal
N/A
N/A
ConnectDevice
(Mfi mode )
SPP
MFi
Default
Default
Default
Default
Default
Default
Default
Default
Default
Auto Connect
Enabled
/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
Auto Reconnect
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power On
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power
On/Power On
Time
disabled, 1sec to
10second(s)
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
Auto Power Off
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
Auto Power
Off/Beep
Warning
Enabled/
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
Auto Power
Off/Power Off
Time
1 to 30 minutes
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
PowerOff Msg
Enabled/Disable
d
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
MAC Address
12 Characters
Bluetooth
MAC
Address
BT FW Version
v1.2.xrt
Bluetooth
Firmware
Version
Wakeup Nulls
Enabled/Disable
d
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
Connect Alert
Enabled/Disable
d
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BT Toggle
Enabled/Disable
d
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
DisconnectBtn
Enabled/Disable
d
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
HID AutoLock
disabled,1,2,3,4,
5,10,15 minutes
1 minutes
1 minutes
1 minutes
1 minutes
1 minutes
1 minutes
1 minutes
N/A
N/A
HID Keyboard
US,German,Fren
ch ,Italian,
Spanish
US
US
US
US
US
US
US
N/A
N/A
HID Delay/Initial
Disabled,
1,2,3,5,10 secs
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
HID Delay/Inter
char
Disabled,10, 20,
30, 50, 100msec
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
HID Ctrl Char
Disabled,
Alt+Numpad,
^+Character,
Replace to |
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
N/A
N/A
BT Service
Power
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Pairing
Pairing
neighboring
Bluetooth
devices
Discovering
Discovering
neighboring
Bluetooth
devices
N/A
N/A
Connecting to
View Connect to
Bluetooth
device
Disconnect
N/A
N/A
N/A
N/A
N/A
N/A
N/A
HID Sync
N/A
N/A
Auto Pairing
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
USB Config-USB
Serial Mode
(M model)
USB Mode
USB Serial/USB
Disk/USB HID
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
USB Serial
N/A
N/A
K
KDC User YOUR KDC
USB Config-USB
Disk Mode
(M model)
USB Mode
USB Serial/USB
Disk/USB HID
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disk Format
Format KDC USB
Disk
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Data Format
Data,DataTime,
DataType,DataTi
meType
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
USB Config-USB
HID Mode
(M model)
USB Mode
USB Serial/USB
Disk/USB HID
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
NFC Config
(N model)
NFC Power
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
N/A
Disabled
Disabled
Data Format
Barcode
only/Packet
Data
Packet Data
Packet Data
Packet Data
Packet Data
N/A
N/A
N/A
N/A
N/A
UID Only
Enabled/
Disabled
N/A
N/A
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
GPS Config
(G model)
GPS Power
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Power Mode
Normal/Power
Save
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Bypass Data
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Acqurie Test
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Reset GPS
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
System
Config
Memory Size(KD
C500)
0.5/2.5, 1/2,
2/1, 3/0
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0.5/2.5
0.5/2.5
Memory Status
No. of Stored
Barcodes
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Free Memory
Available
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Reset Memory
Memory
(Empties Data)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Application
Memory
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BT Registry
(KDC100 Not
use)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Auto Erase
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Sleep Timeout
Disabled, 1sec
to 10minute(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
Date / Time
YYYY:MM:DD &
HH:MM:SS
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Battery
% of Battery
Charge Available
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Version
Firmware
Ve
rsion & Serial
No.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Button Lock
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Beep Alert
/Beep Sound
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert
/Power On Beep
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert
/Beep On
Connect
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert
/Beep On Scan
Enabled/
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Alert
/BeepOnMSCar
d
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Beep Alert
/BeepOnICCard
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Beep Alert
/BeepOnNFCCar
d
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Beep Volume
Low/High
Low
Low
Low
Low
Low
Low
Low
Low
Low
Mfi
( i-chip installed)
Enabled/Disable
d
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
N/A
N/A
Auto Exit
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Port Status
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Display Format
Time & Battery /
Type & Time /
Type & Battery /
Memory Status
/ GPS
Data(KDC250
only)/Barcod
e
Only
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Time &
Battery
Time &
Battery
Menu Barcode
Enabled/
Disabled
N/A
N/A
Disabled
Disabled
N/A
Disabled
Disabled
Disabled
Disabled
Scrolling
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Brightness
1 to 15 level(8
level)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
8
8
Keypad
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Language
US(English)/
Korean/
Japanese
N/A
N/A
N/A
N/A
N/A
N/A
N/A
US(English)
US(English)
Factory Default
Restores Default
Settings
MSR Config
Power
Enabled/
Disabled /
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Data Format
MSR Data Only
N/A
Default
N/A
Default
Default
N/A
N/A
N/A
N/A
Packet Data
N/A
N/A
N/A
N/A
N/A
N/A
Use Track1
Enabled/
Disabled
N/A
Enabled
N/A
Enabled
Enabled
N/A
N/A
Enabled
Enabled
Use Track2
Enabled/
Disabled
N/A
Enabled
N/A
Enabled
Enabled
N/A
N/A
Enabled
Enabled
Use Track3
Enabled/
Disabled
N/A
Enabled
N/A
Enabled
Enabled
N/A
N/A
Enabled
Enabled
K
KDC User YOUR KDC
Null Check
Track1
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Null Check
Track2
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Enabled
Enabled
Null Check
Track3
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
Beep on error
reading
Enabled/
Disabled
N/A
Disabled
N/A
Disabled
Disabled
N/A
N/A
Enabled
Enabled
Encrypt MSR
Data
Enabled/
Disabled
N/A
Disabled
N/A
Disabled
Disabled
N/A
N/A
N/A
N/A
AES Key Length
128bit/192bit/2
56bit
N/A
128bit
N/A
128bit
N/A
N/A
N/A
N/A
N/A
Card Type
ISO/OTHER
1/AAMVA
N/A
ISO
N/A
ISO
ISO
N/A
N/A
ISO
ISO
Track Separator
None/Space/Co
mma/Semicolon
/CR/LF/CR&LF/T
ab
N/A
None
N/A
None
None
N/A
N/A
N/A
N/A
Attach Start/End
Sentinel
N/A
Enabled
N/A
Enabled
Enabled
N/A
N/A
Enabled
Enabled
Partial Data
Start Position
N/A
1
N/A
1
1
N/A
N/A
N/A
N/A
Partial Data
Length
N/A
0
N/A
0
0
N/A
N/A
N/A
N/A
Partial Data
Action
Erase/
Select
N/A
Select
N/A
Select
Select
N/A
N/A
N/A
N/A
ICCR Config
Power
Enabled/
Disabled /
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
IFD Number
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Config Number
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Key Mgmt
Stored Keys
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Inject Keys
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Sensitive/
Set Date/Time
Date
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Time
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Sensitive/
Set Self-Test
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Sensitive/
Set Passwords
1st Password
N/A
N/A
N/A
N/A
N/A
N/A
N/A
2nd Password
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Sensitive/
Key Mgmt
Stored Keys
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Inject Keys
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Clear Keys
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Sensitive/
Card Encrypt
Plaintext / TDES
/
AES
N/A
N/A
N/A
N/A
N/A
N/A
N/A
AES
AES
UHF
Configuration
(UHF model)
UHF Power
Enabled/
Disabled
N/A
N/A
N/A
N/A
N/A
Disabled
Disabled
N/A
N/A
Power On Time
500ms/1sec/1.5
sec/2sec/2.5sec
/3sec/3.5sec/4s
ec/4.5sec/5sec
N/A
N/A
N/A
N/A
N/A
1 second
1 second
N/A
N/A
Power Off Time
500ms/1sec/1.5
sec/2sec/2.5sec
/3sec/3.5sec/4s
ec/4.5sec/5sec
N/A
N/A
N/A
N/A
N/A
1.5 second
1.5 second
N/A
N/A
Power Level
0/1/2/3/4/5/6/7
N/A
N/A
N/A
N/A
N/A
0
0
N/A
N/A
Data Format
Hexa Decimal /
Binary
N/A
N/A
N/A
N/A
N/A
Hexa
Decimal
Hexa
Decimal
N/A
N/A
Table 3 - KDC Menu
K
KDC User YOUR KDC
KDC Mode Menu
The KDC Mode Menu has two options – Normal Mode and Application Mode.
Normal
This is the default mode that provides basic barcode scanning. In normal mode, barcode data may be
manipulated directly through the KDC or through KTSync during the synchronization process.
Application
This mode enables the user to run the user application created by the Application Generation Tool,
as described in Chapter 6 Application Generation.
View Data Menu
This menu option enables the user to view and/or delete barcodes stored in the KDC. In the case of
the KDC20/30, you may delete the last scanned barcode by pressing the DELETE button on the right
side of the unit.
Set Barcodes Menu
This menu lists all the barcode symbologies supported by the KDC and enables the user to select the
barcode symbologies to be scanned. For maximum scan performance, you should select only the
symbologies that you will be scanning. Please refer to 10. Appendix A – 10.1 Symbologies for a
detailed listing of symbologies supported by the KDC.
Code Options Menu
The KDC supports various Code Options, including Transmission of Start and Stop Characters,
Symbology Conversion, Verification of Optional Check Character, and Transmission of Check Digit.
Please refer to 10. Appendix A – 10.2 Code Options for a detailed explanation of each option.
Scan Options Menu
Power(KDC500 only)
Users may choose to turn the Scan Engine Power on or off. Select between Enable and Disable.
Scan Angle (Opticon laser model only)
This option enables the user to configure the laser beam angle to the barcode. There are two
options for scan angle: Wide and Narrow. Wide is 54o and Narrow is 27o. The default is wide.
Press the DDelete button to delete the last
scanned barcode.
Figure 14 - Delete Function in KDC20/30
K
KDC User YOUR KDC
Filter (Opticon laser model only)
This menu enables the user to change the Filter mode from Normal to High for poor quality
barcodes. The default is Normal.
Timeout
In this menu, you may set the scan timeout. The timeout options are from 500ms up to 10 seconds.
The default is 2 seconds.
Minimum Barcode Length
This option enables the user to set a barcode length from 2 characters to 36 characters
(KDC20/100/200/250/270L/350L/410/411/415/470L/500L) or 2 characters to 48 characters
(KDC30/300/350C/420/421/425/450/470C/500C). It is strongly recommended that you maximize
the minimum barcode length setting to prevent possible errors.
¾ The default minimum barcode length of
KDC20/100/200/250/270L/350L/410/411/415/470L/500L is 4 characters.
¾ The default minimum barcode length of KDC30/300/350C/420/421/450/470C/500C is as
follows:
Minimum (Default)
Maximum (Default)
1D Symbology
Codabar
2(4)
60(60)
Code 11
1(4)
80(80)
Code 32
-
-
Code 39
0(0)
48(48)
Code 93
0(0)
80(80)
Code 128
0(0)
80(80)
EAN-8
-
-
EAN-13
-
-
GS1 Composite
-
-
I2of5
2(4)
80(80)
Matrix 2of5
1(4)
80(80)
MSI
4(4)
48(48)
Plessey
4(4)
48(48)
PosiCode
2(4)
80(48)
GS1 Omni
-
-
GS1 Limited
-
-
GS1 Expanded
4(4)
74(74)
S2of5 Ind
1(4)
48(48)
S2of5 IATA
1(4)
48(48)
TCL39
-
-
Telepen
1(1)
60(60)
Trioptic
-
-
UPCA
-
-
UPCE0
-
-
UPCE1
-
-
K
KDC User YOUR KDC
2D S
ymbology
AztecCode
1(1)
3750(3750)
AztecRunes
CodablockF
1(1)
2048(2048)
Code16K
0(1)
160(160)
Code49
1(1)
81(81)
DataMatrix
1(1)
1500(1500)
MaxiCode
1(1)
150(150)
MicroPDF
1(1)
366(366)
PDF417
1(1)
2750(2750)
QRCode
1(1)
3500(3500)
HanXin Code
-
-
Postal Codes
Postnet
-
-
PlanetCode
-
-
UK Post
-
-
Mayada Post
-
-
Kix Post
-
-
Australia Post
-
-
Japan Post
-
-
China Post
2(4)
80(80)
Korea Post
2(4)
80(48)
OCR
OCR Off
-
-
OCR A
-
-
OCR B
-
-
OCR Passport
-
-
OCR MICR
-
-
OCR SEMI
-
-
Image Capture (KDC30/300/270C/350C/420/421/425/450/470C)
This option enables the user to capture an image in JPEG format in C:\myData folder. You should
enable the image capture option first, and then press the Scan button to start the aiming. A green
aiming light will illuminate and an image will be taken upon release of the Scan button. KDC will
disable the image capture option if the user presses the scan button for 5 seconds.
Security Level (Laser Model only)
This menu enables the user to ensure an accurate barcode reading by setting the number of times
the KDC will read a barcode. Security Level is set from 1 up to 4. The higher security level means
readings are more reliable; however, some performance degradation is likely. For poor quality
barcodes, we recommend increasing the security level. The default is 2.
Auto Trigger
Once enabled, Auto Trigger enables the user to scan a barcode automatically. You may adjust reread
delay from continuous to extra-long. Auto Trigger mode always enables the duplicate check
Table 4 - KDC30/300/350C/420/450/500C
Minimum Barcode Length
K
KDC User YOUR KDC
option.(1D Model only)
x USB cable insertion requirement is removed from FW2.85/86.O and FW 3.02.
x You may exit the auto trigger mode by pressing the scan button for 3 seconds.
Reread Delay
You may adjust the reread delay from continuous to extra-long.
Partial Display
This option enables the user to display partial data. You may define the start position and number of
characters to be displayed.
Data Process Menu
Wedge/Store
The KDC provides five modes of data transmission in keyboard wedging mode.
z Wedge Only: Barcode data is NOT stored in memory but transmitted to the host.
z Wedge & Store Only: Barcode data is stored in memory and transmitted to the host.
z Store Only: Barcode data is stored in memory but NOT transmitted to the host.
z Save if Sent: If data transmission is successful, barcode data is stored in memory.
z Save if Not Sent: If data transmission is NOT successful, barcode data is stored in memory.
Data Format
The KDC provides two data formats, Barcode Only and Packet Data.
z Barcode Only: The KDC transmits scanned barcodes only. You may incorporate appropriate
data transmission error detection and correction mechanisms in this mode. KDC supports a
selection of various termination characters for Barcode Only format. You may select
<NONE>, <CR>, <LF>, <CR+LF> or <TAB> as the termination character.
z Packet Data: KDC transmits packet data with checksum to minimize transmission errors.
KTSync sets Data Format to Packet Data format upon execution.
¾ You may change Data Format to Barcode Only if you would prefer to use the Barcode
Only mode. However, the KDC would stay in Packet Data mode if KTSync is aborted
abnormally. If this is the case, you may have to change the KDC back to Barcode Only
mode manually.
x Barcode Index: KDC20i/30i/200i/250i/300i/270i/350i/400i/500i add 4 bytes barcode
index to maintain last synchronized barcode information.
- This optional index would be added if data format is “Packet Data”.
0QVG
0QVG
K
KDC User YOUR KDC
- 4 bytes index would be added before “@” when responding to “p” command.
- 4 bytes index plus “@” character would be added after checksum byte if the
user scans a barcode and wedges to the host.
Data Editor
The KDC provides various data editing options.
z Prefix - Enables user to add a prefix to scanned data that may then be wedged to the host.
The Prefix must be defined in the KTSync. The maximum length for a Prefix is 11 characters.
This Prefix option is different from the Prefix option in KTSync, which attaches the
prefix to data during synchronization.
The user may also define the prefix by scanning characters defined in Appendix
C&D(E&F for KDC500). as shown below in the special barcodes.
KDC20/100/200/250/300/270L/350L/410/411/415/470L/500L
Prefix Enter Start
Prefix/Suffix Enter Finish
KDC30/270C/350C/420/421/425/450/470C/500C
Prefix Enter Start
Prefix/Suffix Enter Finish
0QVG
0QVG
K
KDC User YOUR KDC
Users may also delete or display current prefixes by scanning the following special
barcodes.
KDC20/100/200/250/300/270L/350L/410/411/415/470L/500L
Delete Prefix
Display Prefix
KDC30/270C/350C/420/421/425/450/470C/500C
Delete Prefix
Display Prefix
0QVG
K
KDC User YOUR KDC
z Suffix - Enables the user to add a suffix to scanned data, which may then be wedged to the
host. The suffix must be defined in the KTSync. The maximum length for a suffix is 11
characters.
x This Suffix option is different from the Suffix option in KTSync, which appends the
suffix to data during synchronization.
x The user may also define the suffix by scanning characters defined in Appendix
C&D(E&F for KDC500). as shown below in the special barcodes.
20/100/200/250/300/270L/350L/410/411/415/470L/500L
Suffix Enter Start
Prefix/Suffix Enter Finish
KDC30/270C/350C/420/421/425/450/470C/500C
Suffix Enter Start
0QVG
0QVG
K
KDC User YOUR KDC
Prefix/Suffix Enter Finish
The user may also delete or display a current suffix by scanning the following
special barcodes.
KDC20/100/200/250/300/270L/350L/410/411/415/470L/500L
Delete Suffix
Display Suffix
KDC30/270C/350C/420/421/425/450/470C/500C
Delete Suffix
Display Suffix
z AIM ID - Enables the user to add AIM ID to scanned data, which may then be wedged to the
host. AIM ID can be added to the end of a Prefix or Suffix.
z Partial Data: Enables the user to store and/or transfer partial data. The user defines the
0QVG
K
KDC User YOUR KDC
start position and number of characters to be stored and/or transferred. The user also can
select if taking or erasing the characters selected with Start position and No of char(s).
¾ Start position
This option specifies the start position of data.
¾ No of char(s)
This option specifies the length of data. The ‘0’ means all data.
¾ Action
This option selects if erasing or taking the specified data.
Handshake(KDC500 doesn’t support it)
KDC provides Handshake mode when Data Format is set to Packet Data.
z Handshake Mode will increase the reliability of barcode data transmission.
z The default mode for Handshake is disabled.
z Data transmission speed is slower when Handshake Mode is enabled.
Terminator
The KDC supports various termination characters when the Data Format mode is set to Barcode
only. Select <NONE>, <CR>, <LF>, <CR+LF>, or <TAB> as the termination character. The default
terminator is <CR+LF>. The Up/Down/Left/Right arrow terminator is also available for HID mode.
Chk Duplicate
This option prevents you from collecting duplicate data.
Enter Key (KDC350/500 only)
This option determines the behavior of the ‘#’ key on the keypad.
z If this option is enabled, the ‘#’ key acts as a keyboard enter key.
¾ The ‘#’ key finishes the current data input, and stores/sends input data according to
the menu settings of Wedge/Store.
¾ The cursor moves to next line after the current data input is complete, regardless of
whether there is a data input or not.
¾ The screen is scrolled up one line if the ‘#’ key is pressed on the last line of KDC screen.
¾ If ‘Shift’ is enabled, remember that the ‘#’ key will input the ‘#’ character.
Extend Key (KDC350/500 only)
This option enables users to enter more symbols by using keypad.
Age Verification (KDC30/300/270C/350C/420/421/425/450/470C)
This option enables to verify age by reading driver license.
K
KDC User YOUR KDC
BT Config Menu – KDC20/30/200/250/300/270/350/400/500
The KDC supports Bluetooth Ver2.1+EDR. Before utilizing the advantages of Bluetooth functionality
with the KDC, the user should become familiar with Bluetooth connectivity and its impact on the
host environment.
To configure your KDC for Bluetooth functionality, you may use the KDC Menus.
Below is a listing of the Bluetooth options and their settings. The default settings for these options
have been set to increase the usability of Bluetooth technology without compromising the KDC
battery usage.
IMPORTANT: We strongly recommend NOT changing these settings until the user has
fully tested the Bluetooth connection between the KDC and the host device.
For more detailed information regarding Bluetooth functionality with the KDC, please refer to
Chapter 4. BLUETOOTH.
ConnectDevice
You may choose the Bluetooth device type in this option.
z HID normal - KDC20(i)/30(i)/200(i)/250(i)/300(i)/270(i)/350(i)/400(i)
z HID iOS - KDC20(i)/30(i)/200(i)/250(i)/300(i)/270(i)/350(i)/400(i)
z SPP2.0 - KDC20(i)/30(i)/200(i)/250(i)/300(i)/270(i)/350(i)/400(i)
z SPP - KDC20(i)/30(i)/200(i)/250(i)/300(i)/270(i)/350(i)/400(i)/500(i)
z MFi - KDC20i/30i/200i/250i/270i/300i/270i/350i/400i/500i
Auto Connect
Enabled or Disabled(KDC500 doesn’t support)
Auto Reconnect
Enabled or Disabled
Auto Power On
Enabled or Disabled(KDC500 doesn’t support)
PWR On Time
Disabled, 1 to 10 seconds(KDC500 doesn’t support)
Auto Power Off
Enabled or Disabled (KDC250G/350G should use option in system menu)
(KDC500 doesn’t support)
K
KDC User YOUR KDC
Beep Warning
Enabled or Disabled(KDC500 doesn’t support)
PWR Off Time
1 to 30 Minutes(KDC500 doesn’t support)
PowerOff Msg
Enabled or Disabled(KDC500 doesn’t support)
MAC Address
When users select this option, KDC displays 12 characters Bluetooth MAC Address.
FW Version
This option displays Bluetooth Firmware Version
Wakeup Nulls
Enabled or Disabled(KDC500 doesn’t support)
BT Toggle
Enable or Disable iOS device soft keyboard or Connect/Disconnect Bluetooth. (KDC500 doesn’t
support)
BT Disconnect Button
Enable or Disable Bluetooth disconnection by pressing down button for 3 seconds. (KDC500
doesn’t support)
HID AutoLock
Disabled, 1, 2, 3, 4, 5, 10, 15 minutes(KDC500 doesn’t support)
HID Keyboard
Users may select a keyboard language in HID mode. KDC supports five languages: English,
German, French, Spanish, and Italian. (KDC500 doesn’t support)
HID Initial Delay
In this menu, users may define the initial delay between 1 second to 10 seconds before data
transmission in HID mode(KDC500 doesn’t support)
HID Inter-character Delay
This option enables users to define the inter-character delay between 10msec to 100msec in
HID mode(KDC500 doesn’t support)
HID Control Character
This option helps users to map control characters to ALT+Numlock or ^+Character_or ‘|’.
(KDC500 doesn’t support)
K
KDC User YOUR KDC
BT Service Menu – KDC20/30/200/250/300/270/350/400/500
Power
Users may choose to turn Bluetooth Power on or off. Select between Enable and Disable.
Pairing Mode
This option Enables user to enter pairing mode by simply selecting this menu.
z The KDC enters into pairing mode so that the host Bluetooth device may search for it.
z The KDC may exit pairing mode if the user presses the SCAN button or if it fails to pair with
the Bluetooth host device within 90 seconds.
Discovering
When users choose this menu, KDC searches for nearby Bluetooth devices. (KDC500 doesn’t support)
Connecting To
This option enables the user to inquire to a registered Bluetooth device. (KDC500 doesn’t support)
Disconnect
This option enables the user to disconnect KDC from the paired Bluetooth device. (KDC500 only)
HID Sync
KDC transmits all stored data to the host over HID profile if HID Sync option is enabled. (KDC500
doesn’t support)
Auto Pairing
Enables or Disable the automatic Host Bluetooth type detection (SPP or MFi).(i Model only)
GPS Config Menu – KDC250G/350G
Barcode and GPS data format
The GPS enabled model adds the GPS coordinate after the barcode data, if GPS data is available. The
GPS data starts with “<G|P/S]” and ends with “:”. For example, the GPS enabled model would
record barcode “1234567890” , GPS coordinate “4354.45275,N;07925.81993,W” and Altitude data
“208.7,M”as “1234567890<G|P/S]4354.45275,N;07925.81993,W ,208.7,M:” in the barcode data
field.
GPS Menu
z GPS Power: Turning GPS Power on or off
¾ Users may enable or disable the GPS Power.
¾ The GPS module consumes extensive battery power. To conserve battery power, it is
strongly recommended to turn off the GPS option when the GPS enabled model is not
being used for an extended period of time.
¾ It is also recommended to use the GPS Auto Power Off option in the SystemConfig
menu. This option automatically turns off the GPS power if a barcode is not scanned for
K
KDC User YOUR KDC
a period of time.
z Power Mode: The user may choose the type power consumption for the GPS function.
¾ Users may extend the battery life of the GPS enabled model in Power Save mode.
¾ Users should use normal mode if accurate GPS data is required.
¾ The KDC350G will last about 15 hours in normal non-bypass data mode and 18 hours
in power save non-bypass data mode.
¾ The KDC350G will last about 7 hours in normal bypass data mode and 8 hours in
power save bypass data mode.
z Bypass Data: Enabled or Disabled
¾ This option should be disabled if users wish to record the GPS data with a scanned
barcode data.
¾ The KDC will bypass GPS data to the host if the bypass option is enabled.
¾ The KDC becomes a Bluetooth GPS receiver if this bypass data option is selected.
z Acquire Test: Select to acquire GPS signal.
z Reset GPS: Reset KDC GPS module.
GPS Hot Key
The KDC250G/350G provides the following hot keys for convenient GPS operations:
z GPS Acquire Test Cancellation
¾ Users may cancel the GPS acquire test by pressing the SCAN button during the test.
z GPS Data Append Cancellation
¾ Users may cancel GPS data append by pressing SCAN button if GPS data is not
available immediately.
¾ Users should hold the SCAN button for more than 3 seconds to cancel GPS data
append.
USB Mode Menu– 100M/200M/250M/300M/270/350
Disabled
When this option is selected, KDC enters into USB Serial mode.
USB Disk
K
KDC User YOUR KDC
This option enables the user to change to USB Disk mode and barcode data that KDC scanned is
stored into a file in flash disk when this option is selected.
KDC100M/200M/250M/300M/350 may be used as USB Disk with 4MB or 8MB space and KDC270
may be used as USB Disk with 8MB space.
USB HID
When this option is enabled, KDC enters into USB HID mode.
Disk Format
This option is available in USB Disk mode and Enables users to format KDC USB Disk.
Data Format
This option is available in USB Disk mode.
z Data
z Data Time
z Data Type
z Data Time Type
x Changing the “USB Mode” option will erase all data in KDC memory.
Make sure to back up your data before changing this option.
x KTSync may not recognize the KDC if the KDC is in “USB DISK” mode or “USB HID” mode.
0QVG
K
KDC User YOUR KDC
NFC Config Menu – KDC350N/411N/415N/421N/425N/500
NFC Power
z Turning NFC Power on or off
z Options: Enable/Disable
Data Format
z Options: Data only/Packet data.(KDC500 doesn’t support)
UID Only
z Enable or Disable UID Only menu
z The KDC only sends UID data to the host device when the KDC is in UID Only mode.
z (KDC500 doesn’t support)
UHF Config Menu – KDC450U
UHF Power
z Turning UHF Module Power On or Off
z Options: Enable/Disable
Power On Time
Specify the power on time duration of UHF module.
z Options: 500ms/1sec/1.5sec/2sec/2.5sec/3sec/3.5sec/4sec/4.5sec/5sec
Power Off Time
Specify the power off time duration of UHF module.
z Options: 500ms/1sec/1.5sec/2sec/2.5sec/3sec/3.5sec/4sec/4.5sec/5sec
Power Level
Specify the UHF module power level to determine the power strength of antenna. 7 means the most
power strength.
z Options: 0/1/2/3/4/5/6/7
Data Format
Specify the data format of UHF data when it is transmitted from KDC to Host.
z Options: Binary / Hexa Decimal
K
KDC User YOUR KDC
Smart Hopping
It enables KDC450U to find an optimized UHF channel and can be initiated by reading a special
barcode.
WIFI Config Menu (KDC350F)
KDC350F WiFi model can send and receive data to/from host by using the following protocols.
z UDP
z TCP
z HTTP_GET
z HTTP_POST
In UDP/TCP mode, KDC350F will support full duplex mode, meaning is the KDC350F will be ready to
get data from host all the time.
Power
z Turns the Wi-Fi Module Power ON and OFF.
AP
z Set AP SSID.
z Set AP Passcode.
Server
z Configure the following server information
IP Address
URL Address
Port Number
Protocol (UDP/TCP/HTTP-GET/HTTP-POST)
SSL(Security)
Server Page
Connect
z Connect to AP and server.
Auto Connect
z Enable/Disable KDC to reconnect to AP & Server when it detects disconnection from AP and
Server.
K
KDC User YOUR KDC
Send Stored
z Enable/Disable KDC to send stored data when sending a new read data.
CDMA Config Menu (KDC350WA CDMA)
KDC350WA CDMA model can send and receive data to/from host by using the following protocols if
and only if the device is activated and the Verizon network is available.
z UDP
z TCP
z HTTP_GET
z HTTP_POST
In UDP/TCP mode, KDC350WA will support full duplex mode, meaning is the KDC350WA will be
ready to get data from host all the time.
Power
z Turns the CDMA Module Power ON and OFF.
Provisioning
z Activates the device under Verizon CDMA network.
Server
z Configure the following server information
IP Address
URL Address
Port Number
Protocol (UDP/TCP/HTTP-GET/HTTP-POST)
SSL(Security)
Server Page
Resp. Timeout
Connect
z Connect to Server.
Disconnect
z Disconnect from Server.
Auto Connect
K
KDC User YOUR KDC
z Enable/Disable KDC to reconnect to Server when it detects disconnection from Server.
Send Stored
z Enable/Disable KDC to send stored data when sending a new read data.
Information
z Displays CDMA module firmware version, the CDMA number, MEID, and IP address.
MSR Config Menu – KDC415/425/430/500
Power(KDC500 only)
z Turning MSR(Magnetic-Stripe Card Reader) on or off
z Options: Enabled/Disabled
Data Format(KDC415/425/430 only)
z Enables/Disables whether KDC415/425/430 sends with packet data or not.
z Options: Enabled/Disabled
Use Track
The user may select which track(1/2/3) data to read from the MS Card.
z Track 1 : Enabled/Disabled
z Track 2 : Enabled/Disabled
z Track 3 : Enabled/Disabled
Null Check(KDC500 only)
The user may select which track(1/2/3) data should not be null. When this option is enabled for a
Track and the read data is null, MS Card read fail occurs.
z Track 1 : Enabled/Disabled
z Track 2 : Enabled/Disabled
z Track 3 : Enabled/Disabled
Beep On Error
When this option is enabled, KDC makes a beep sound when it fails to read a MS card.
Encrypt MSR Data(KDC415/425/430 only)
z If enabled, KDC415/425/430 sends MSR data with AES encrypted.
z Options: Enabled/Disabled
K
KDC User YOUR KDC
AES Key length(KDC415/425/430 only)
z Specify the AES key length.
z Options: 128bits/192bits/256bits
Card Type
The user may select which type of MS card to read.
z ISO
z OTHER 1
z AAMVA
z JIS(KDC500 only)
Track Separator(KDC415/425/430 only)
z Specify the separator which will be added between track data
z Options: None, Space, Comma, Semicolon, CR, LF, CR&LF, Tab
Attach SS/ES
When this option is enabled, KDC does not exclude the Start Sentinal(SS) and End Sentinal(ES)
control characters in the track data when it sends the card data to the connected Host device.
Partial Data(KDC415/425/430 only)
Enables the user to transfer partial MSR data. The user defines the start position and number of
characters to be transferred.
z Start position
This option specifies the start position of data.
z No of char(s)
This option specifies the length of data. The ‘0’ means all data.
z Action
This option selects if erasing or taking the specified data.
K
KDC User YOUR KDC
ICCR Config Menu – KDC500
Power
z Turning ICCR(IC Card Reader) on or off
z Options: Enable/Disable
IFD Number
This option shows the EMV IFD(Interface Device) number.
Config Number
The option shows the stored EMV Contact Configuration number.
K
KDC User YOUR KDC
SystemConfig Menu
Memory Size (3.0+ version only, KDC500 doesn’t support)
The user may select how much memory to divide between normal data memory and application
database memory.
z The KDC will erase all stored data upon changing the partition size.
z The user should enter the following key sequence to change the partition.
UP button + UP button + DOWN button + DOWN button + SCAN button
Memory Status
In this option, users may checks the number of stored barcodes and memory usage.
Reset Memory
In this option, users may reset KDC memory by erasing all stored barcodes, applications, and BT
registry. KDC500 only erase all stored barcodes.
Auto Erase
If enabled, this feature erases stored barcodes on the KDC once the ‘Buffer Full’ condition is reached.
Sleep Timeout
This option Enables users to set the amount of time the KDC waits before going to sleep (when not
being used).
Auto Power Off (KDC250G/350G)
z Bluetooth: Enabled/Disabled
z GPS: Enabled/Disabled
z Power Off Time:0(Never), 5, 10, 20, 30, 60, 120 minutes
Date/Time
In this option, users may set the date and time of the KDC, which may also be set using
KTSync.(except KDC500)
Battery
This option shows the current status of battery power level.
Version
This option shows the KDC firmware version and serial number.
KDC500 displays only firmware version.
Serial Number(KDC500 only)
KDC500 displays the serial number
Button Lock
This option enables the user to lock or unlock the KDC scan and scroll buttons.(KDC500 doesn’t
support)
Beep Alert
z Beep Sound: Enables or disables KDC beep sound.
K
KDC User YOUR KDC
z Power On Beep: Enables or disables beep sound when KDC power is on.
z Beep On Connect: Enables or disables beep sound when KDC is connected to the host.
z Beep On Scan: Enables or disables beep sound when KDC is scanning.
z Beep On MS Card (KDC500 only) : Enables or disables beep sound when KDC reads a MS
Card.
z Beep On IC Card (KDC500 only) : Enables or disables beep sound when KDC reads an EMV
Contact Card.
z Beep On NFC Card (KDC500 only) : Enables or disables beep sound when KDC reads an NFC
Tag or EMV Contactless Card.
Beep Volume
This option enables the user to adjust the beep volume from High to Low.
MFi Mode (KDC20i/30i/200i/250i/270i/300i/350i/400i)
This option Enables user to enable or disable MFi mode. MFi mode supports SPP and MFi Bluetooth
profiles. Non-MFi mode supports SPP, SPP2.0, HID iOS and HID normal.
Vibrator(KDC20/30/270/350)
Enables, disables and configure KDC vibrator.
x There are two additional options for KDC vibrator configuration.
o Scan Success Î Specify the number of vibration when scan successfully.
o Scan Failure Î Specify the number of vibration when scan failed.
Auto Exit
This option enables KDC to automatically exit KDC Menus.
Port Status
This option enables users to enable or disable KDC port messages.
Display Format
There are various selections of display format; Time & Battery, Type & Time, Type & Battery,
Memory Status, Barcode only and Graphics.
The Graphics option enables to display ‘O’ for scan success and ‘X’ for scan failure.
Menu Barcode
This option enables users to enable or disable Honeywell special barcodes (KDC300/350C/500C
only).
Scrolling
This option enables users to enable or disable display scrolling for a barcode with more than 40
characters.(KDC500 doesn’t support)
Brightness
This option enables users to adjust brightness of display.
K
KDC User YOUR KDC
Keypad(KDC350/500)
This option enables users to enter data by using keypad.
Language(Version 3.0+, KDC500)
This option enables users to select KDC display languages.
The supported languages are as following.
z None – Languages is not supported. Default is an English.
z US(English)
z French
z Italian
z Spanish
z Korean
z Japanese
KDC500 only supports US(English), Korean and Japanese.
Factory Default
By selecting this option, users may reset KDC options to factory default settings.
K
KDC User YOUR KDC
Key Mgmt Menu– KDC500
z Stored Keys : Displays all the encryption keys stored in the KDC500.
z Inject Keys : In this menu, the user can inject the necessary encryption keys via Key Loader
device.
K
KDC User YOUR KDC
Sensitive Menu – KDC500
KDC500 Sensitive menu has sub menus which can impact on the KDC500 security services. KDC500
requires two passwords for the Sensitive menu group access in order to ensure only authorized
people can utilize the sensitive services. The default passwords are 0000000 and 11111111.
x For PCI PTS compliance, the default passwords should be changed prior to use. Without
the default passwords change, KDC500 declines all the payment related service
requests; such as MS Card Read, IC Card Insertion, PIN Entry, etc.
Set Date/Time
In this menu, the user can set the date and time of the KDC500.
Set Self-Test
The user can set the time for the Self-Test in this menu. In PCI PTS, it requires to perform the Self-
Test(Firmware and stored key authentication) at least once in 24 hours.
Set Passwords
In this menu, the user can change the current passwords to access the Sensitive Menu.
Key Mgmt
z Stored Keys : Displays all the encryption keys stored in the KDC500.
z Inject Keys : In this menu, the user can inject the necessary encryption keys via Key Loader
device.
z Clear Keys : In this menu, the user can clear all the encryption keys stored in the KDC500
except the Firmware Update Authentication key which is loaded during the manufacturing
process.
Card Encrypt
This menu allows user to choose the encryption algorithm for the sensitive card data from the list
below.
z Plaintext
z T-DES
z AES
0QVG
K
KDC User YOUR KDC
3.4
LED Status
Table 5 - Explanation of LEDs
3.5
Empty Battery
KDC100/200/250/300/270/350
The KDC will display the message Empty Battery Connect USB when the battery is empty. Please
charge the KDC IMMEDIATELY to prevent any interruptions while it is collecting data.
KDC20/30/400
x Under 30% - Orange LED flickers at 1-second-intervals for 5 seconds every minute.
x Under 20% - Orange LED flickers at 1-second-intervals for 10 seconds every minute.
x Under 10% - Red LED flickers in 1- second-interval for 10 seconds every minute, and the user
will hear a beeping sound.
KDC500
x Under 10% (Low) Displays the message Low Battery Please Charge. KDC500 is still
functional, but charge the KDC500 IMMEDIATELY to prevent any interruptions while it is
collecting data.
x Under 5% (Empty) - Displays the message Empty Battery Please Charge. KDC500 is not
functional any longer.
LED Color Status
Green
z
Successful Reading
z USB is connected and battery
is fully charged.
z MFi mode in pairing mode.
Orange
z
Low battery
z USB is connected and battery is charging
z HID mode is in pairing mode. (ex
cept KDC500)
Red z
No reading
z SPP mode is in pairing mode.
K
KDC User YOUR KDC
3.6
Buffer Full
The KDC will display the message Buffer Full when there is no more space in the flash memory or the
number of collected barcodes reaches the maximum number of stored barcode. To prevent the loss
of data, you should synchronize the data then reset the memory when this message is displayed.
The 4MB/8MB version KDC reaches the Buffer Full condition in the following situations:
x 0.5MB Partition - Collected data size reaches 0.5MB or collected number is 25,600
x 1MB Partition - Collected data size reaches 1MB or collected number is 51,200
x 2MB Partition - Collected data size reaches 2MB or collected number is 102,400
x 3MB Partition - Collected data size reaches 3MB or collected number is 153,600
x 4MB Partition - Collected data size reaches 4MB or collected number is 204,800
x 5MB Partition - Collected data size reaches 5MB or collected number is 256,000
x 6MB Partition - Collected data size reaches 6MB or collected number is 307,200
x 7MB Partition - Collected data size reaches 7MB or collected number is 358,400
x 8MB Partition - Collected data size reaches 8MB or collected number is 409,600
K
KDC User YOUR KDC
3.7
Reset Feature (100/200/250/300) or
Power-on/off (KDC20/30/270/350/400/500)
The Reset feature enables the user to restart the KDC100/200/250/300 if necessary, without losing
any stored barcode data or option settings. To reset the KDC, follow the below steps.
1. Press the DOWN and SCAN buttons simultaneously for 5 seconds.
2. When the LEDs illuminate orange, release the buttons.
3. The KDC initial screen, KoamTac Data Collector KDC, displays when reset is complete.
The KDC stores collected data into flash memory and will not lose data nor the KDC
settings during the reset process.
If you are using the KDC20/30/270/350, you may turn the power on and off by pressing the DOWN
and SCAN button simultaneously for 5 seconds. When the LED light is green, you may release the
buttons and the power will be on. When you turn off the KDC20/30/270/350/470, you will hear a
beep sound after pressing the DOWN and SCAN buttons simultaneously.
If you are using the KDC400 (except KDC470) you may turn the power on and off by sliding the
power switch.
If you are using the KDC500, you can turn the power on and off by pressing the left and right SCAN
buttons simultaneously for 5 seconds. When the display shows KOAMTAC logo, you may release the
buttons and the power will be on. When you turn off the KDC500, you will see the display shows
blank after pressing the left and right SCAN buttons simultaneously.
0QVG
K
KDC User YOUR KDC
Unscrew the screw indicated by
the arrow.
Remove the battery cover by
pulling it down.
Remove the battery.
Pull out the 2 pin connecter
gently.
3.8
Replace Battery
Each KDC comes with a rechargeable, Lithium-polymer (KDC20/100/200) or Lithium-ion
(KDC30/250/300/270/350/400/500) battery. The battery may be recharged from any USB port or
KDC charging cradle, and may be recharged about 300 times before it needs to be
replaced. KOAMTAC recommends replacing the battery annually, as a declining battery will cause
noticeable performance degradation in the KDC. Replacement batteries may be purchased from a
KDC reseller. Batteries should be disposed of properly as according to the WEEE regulation. The
steps for replacing a battery are as follows.
1. Disassemble the KDC back cover by unscrewing the middle screw.
2. Remove the old battery and replace with a new battery.
3. Reassemble the back cover.
Figure 15 - Replacing a Battery
K
KDC User Manual BLUETOOTH
4. Bluetooth -
KDC20/30/200/250/300/270/350/400/500
The KDC20/30/200/250/300/270/350/400 supports HID (Human Interface Device) normal, HID iOS,
SPP (Serial Port Profile) and SPP2.0 profiles. The KDC500 supports SPP only. The
KDC20i/30i/200i/250i/300i/270i/350i/400i/500i supports MFi (Made for iPhone/iPad/iPod touch)
profiles too. They are compatible with the following Bluetooth stacks:
z BlueSoleil
z Broadcom (Widcomm)
z Microsoft Windows XP, Vista, 7, 8, 10, and Mobile 5.0+
z Toshiba
For PCI PTS compliance, KDC500 can support only SPP and MFi profiles.
The KDC200/250/300/270/350/500’s Bluetooth options may be configured by using the KDC menu,
PC KTSync and special barcodes. The KDC20/30/400’s Bluetooth options may be configured by using
the PC KTSync and special barcodes.
4.1
Bluetooth Config
Connect Device
The KDC supports both Serial Port Profile (SPP) and Human Interface Device Profile (HID). The user
may choose amongst SPP2.0, SPP (2.1), HID normal, or HID iOS profiles to communicate with the host
device. An additional MFi (Made for iPhone/iPad/iPod touch) option is available for
KDC20i/30i/200i/250i/300i/270i/350i/400i/500i models when MFi mode is enabled.(SystemConfig
Menu). KDC500i doesn’t have MFi mode option and supports MFi by default.
If the BT Toggle option(KDC500 doesn’t support) in BT Config is enabled, the user may connect and
disconnect the Bluetooth connection with the host device by pressing the UP and DOWN buttons. It
normally takes 3 seconds to connect and 1 second to disconnect. This is a very useful feature for
iPhone and iPad applications.
The user may also enable and disable the iPhone and iPad soft keyboard instantly by using this BT
Toggle option in HID mode.
The UP button shows the Bluetooth connection status and the DOWN button shows the time when
this option is disabled.
0QVG
K
KDC User Manual BLUETOOTH
The user should first un-pair the KDC from the Bluetooth host to change the Connect
Device setting on the scanner to a different Bluetooth profile.
Auto Connect
This feature enables the KDC to automatically connect to the host device when the KDC is powered
on. KDC500 doesn’t support Auto Connect.
IMPORTANT: Until the host device and the KDC have been fully tested, it is strongly recommended
that this feature be set to ‘Disabled’, because a host device that does not support this feature could
cause problems, such as power loss or upload delays.
The KDC automatically tries to connect to the host 10 times within the duration of two
minutes when Bluetooth power is ON, Bluetooth is disconnected, Auto Connect is
enabled, and system Sleep Timeout is set to 5 seconds.
Auto Reconnect
This feature enables the KDC to automatically connect to the host device when the KDC is
disconnected from a host.
The KDC tries to connect automatically to the host 10 times within the duration of two
minutes if Bluetooth is disconnected.
Auto Power On
The Auto Power On option Enables the KDC to automatically power on Bluetooth when the SCAN
button is pressed. The default setting is Disabled. KDC500 doesn’t support this option.
Users should press the scan button for the duration defined in the BT Config Power-on
time option. The host program may have to open the COM port again in order to be
reconnected with the KDC.
PWR ON Time
The PWR On Time option works in conjunction with the Auto Power On option. The default value is
Disabled. If the KDC Bluetooth power is off, you may turn on the Bluetooth power by pressing the
SCAN button for the PWR On Time option value. KDC500 doesn’t support this option.
Auto Power Off
The Auto Power Off option works in conjunction with the PWR Off Time option. This option Enables
the KDC to power off Bluetooth automatically when the KDC is NOT CONNECTED to the host for the
time duration specified in the PWR Off Time option. KDC500 doesn’t support this option.
0QVG
0QVG
0QVG
0QVG
K
KDC User Manual BLUETOOTH
The default for this option is disabled. It is strongly recommended to keep it enabled to maximize
the operation time of the KDC. If Auto Power Off is Enabled, Bluetooth may be manually powered off
before the specified time in the PWR off time option.
It is recommended to enable ‘Auto Power On’ option if this option is enabled. User doesn’t need to
turn on the Bluetooth power manually with this configuration.
Beep Warning
The KDC beeps to warn user to power off the Bluetooth if this option is enabled with five short
beeps when the following condition meets..
1. Bluetooth power is ON
2. KDC is disconnected
3. Auto Power Off is DISABLED
KDC500 doesn’t support this option.
PWR OFF Time
The PWR Off Time option works in conjunction with the Auto Power Off option. If Auto Power Off
is Enabled, the KDC powers off Bluetooth when the duration of time specified in the PWR Off Time
option is met and the KDC is NOT CONNECTED to the host. The time setting for this option is from
one (1) minute to 30 minutes. The default is five (5) minutes. KDC500 doesn’t support this option.
PowerOFF Msg
The KDC sends a Bluetooth power off message “BTOFF” to the host when KDC is connected from
host if this option is enabled. KDC500 doesn’t support this option.
MAC Address
The user may verify the KDC Bluetooth MAC Address.
FW Version
The user may verify the KDC Bluetooth firmware version in this menu.
Wakeup Nulls
The KDC sends three leading Null bytes to wake up the Bluetooth connected device. This feature may
be disabled if the Bluetooth connected device does not require additional bytes to wake up. KDC500
doesn’t support this option.
Autolock Time
The iPhone/iPad/iPod touch loses incoming Bluetooth data while in sleep mode. To prevent data loss,
you may set the KDC Autolock time to the same Autolock time of your iPhone/iPad/iPod touch, to use
the automatic wakeup feature in HID mode. KDC500 doesn’t support this option.
K
KDC User Manual BLUETOOTH
If the Autolock time is set to more than one minute and the barcode scan interval is larger than the
auto-lock time, there will be a one second delay of barcode transmission. The auto-lock time would be
set as 0, 1, 2, 3, 4, 5, 10, 15 minutes. 0 means the iPhone/iPad/iPod touch never enters sleep mode. This
option may not need from iOS 5.x.
HID Keyboard
The user may select an international keyboard – English, German, French, Spanish, or Italian. It is
also required to set the host keyboard with the same keyboard as selected in this menu. KDC500
doesn’t support this option.
HID Initial and Inter-Character Delay
Certain applications may not process HID input fast enough and may lose some characters during
transmission. Users should increase initial and inter-character delay to prevent data loss during HID
transmission. KDC500 doesn’t support this option.
z HID Initial Delay: Defines the initial delay between 1 sec to 10 sec before data
transmission in HID mode.
z HID Inter-character Delay: Defines the inter-character delay between 10msec to
100msec in HID mode.
Control Character Transmission in HID mode
Control characters between ASCII values 0x00 and 0x1F may be replaced by the ALT+Numpad or
^+Character or replaced with ‘|'. KDC500 doesn’t support this option.
z Disabled Î Transmit the original control character.
z Alt+Numpad Î Transmit Alt+ ASCII value from Numpad.
z ^+Character Î Control characters would be substituted as shown in the following table.
z Replacement to | Î Control characters would be substituted as “|”.
Control
Char
Transmit
Chars
Control
Char
Transmit
Chars
Control
Char
Transmit
Chars
Control
Char
Transmit
Chars
0x01
^A
0x0B
^K
0x14
^T
0x1D
^]
0x02
^B
0x0C
^L
0x15
^U
0x1E
^^
0x03
^C
0x0E
^N
0x16
^V
0x1F
^_
0x04
^D
0x0F
^O
0x17
^W
0x05
^E
0x10
^P
0x18
^X
0x06
^F
0x11
^Q
0x19
^Y
0x07
^G
0x12
^R
0x1A
^Z
0x09
^I
0x13
^S
0x1C
^\
K
KDC User Manual BLUETOOTH
Function Key Transmission in HID mode
The user may send F1 to F12 function keys by scanning special barcodes in HID mode. KDC500 doesn’t
support this option.
Disconnect/Reconnect/BT(HID) Toggle
The user may disconnect or reconnect the Bluetooth connection, and toggle the soft keyboard using
side buttons. KDC500 doesn’t support this option.
Some SPP host doesn’t support Reconnection from KDC.
Bluetooth
Profile
UP Key
DOWN Key
(DisconnectBTN disabled)
DOWN Key
(DisconnectBTN enabled)
SPP
Reconnect
Does nothing
Releases BT connection
HID iOS
Reconnect
Soft Keyboard Toggle if
pressing less than 3sec
Soft Keyboard Toggle if
pressing less than 3sec,
Releases BT connection
MFi
Reconnect
Does nothing
Releases BT connection
SPP 2.0
Reconnect
Does nothing
Releases BT connection
HID normal
Reconnect
Does nothing
Releases BT connection
0QVG
K
KDC User Manual BLUETOOTH
4.2
Bluetooth Service
Power
The POWER option enables the user to Enable or Disable the Bluetooth functionality of the KDC. To use
Bluetooth, this option must be set to enable.
However, like all devices enabled for Bluetooth, the KDC will constantly search to connect with a
Bluetooth host when set to enable. Constant searching for Bluetooth devices increases power
consumption.
Unless you are using Bluetooth with your KDC, this option should be set to disable.
IMPORTANT: To prevent unnecessary power problems, it is strongly recommended that the POWER
option be set to disable if the KDC is idle for an extended period of time.
Pairing
Before you are able to use Bluetooth, the KDC must be paired with the host device. This pairing
process needs to be completed only once with each host device. After pairing, the host device will
always recognize the KDC as a Bluetooth device, unless the Bluetooth configuration is modified. If it is
modified, you may need to pair the devices again.
IMPORTANT: The host device must be configured for Bluetooth before it may be paired to the KDC.
KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
To pair the KDC20/30/200/250/300/270/350/400 with the host, follow these instructions:
1. Select Pairing from the Bluetooth menu. The message “Pairing started…” will be
displayed.
2. The “Pairing Done” message will display when the Bluetooth connection is
successfully established. The connection must be established before the pairing
timeout of 90 seconds.
z If “Pairing failed...” message displays, the Bluetooth connection with the host device
failed. If the message “Connected” displays, a Bluetooth connection is established.
z It is possible for the message “Pairing failed...” to display on the KDC while the host
device displays the “Connected” message. If this occurs, a Bluetooth connection has
been established.
For KDC500 paring with the host, Numeric Comparions pairing method is required for PCI PTS
complicance. See the section 2.1 Bluetooth Paring for the details.
0QVG
K
KDC User Manual BLUETOOTH
Discovering
KDC200/250/300/270/350 starts to search for neighboring Bluetooth devices if the Discovering menu
is executed. It will take about 30 seconds to finish searching and to list available neighboring
Bluetooth devices. Another option is to enter the corresponding Bluetooth MAC address in the
KTSync Bluetooth menu, instead of waiting for the KDC to search for neighborhood Bluetooth devices.
KDC20/30/400 only supports via KTSync configuration. KDC500 doesn’t support this feature.
Connect To
This option lets you easily connect the KDC to Bluetooth devices that have been either previously
registered in KTSync under the File Menu or discovered/connected from the KDC Bluetooth Service
menu. KDC20/30/400 only supports via KTSync configuration. KDC500 doesn’t support this feature.
There could be an interoperability issue depending on the corresponding device
Bluetooth stack. The master Bluetooth device may request that you to follow the
master Bluetooth device’s security procedures, if the KDC tries to connect to the master
Bluetooth device.
HID Sync
The user may synchronize stored barcode data over HID using the HID Sync option. The KDC will start
to transmit all stored barcode data upon execution of the HID Sync option. KDC500 doesn’t support
this feature.
Tips
Pair and connect KDC20i/30i/200i/250i/300i/270i/350i/400i and iOS4.0+ in HID iOS mode
x Users have to disable the MFi option in System > MFi menu and change the Bluetooth
profile to HID-iOS to use HID Bluetooth profiles.
x Users have to RESET the iPhone/iPad/iPod touch in order to change HID to MFi mode,
and vice versa, after removing a previous KDC connection.
x KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
x KDC with Bluetooth Spec. 2.1+EDR stack does not require 4 or 6 digits PIN digits entry
Follow the below steps in order to pair and connect KDC models for MFi and iOS4.0+ in HID
mode.
1. Go to the MFi menu of KDC SystemConfig Menu
2. Change MFi option to Disabled
3. Change ConnectDevice to HID iOS mode
4. Remove previous KDC connection and RESET the device
5. Change KDC to Pairing mode
0QVG
0QVG
K
KDC User Manual BLUETOOTH
6. The iPhone/iPad/iPod touch will find a new device as Keyboard
7. Click Keyboard device
iOS Soft Keyboard Toggling using BT Toggle Option.
Users need to select the option to use this feature in BT Config>BT Toggle. Press the DOWN button to
toggle a soft keyboard.
Auto Pairing
For SPP and MFi mode, user used to select host profile before pairing. However, user doesn’t need to
select host device profile if this option is enabled. KDC automatically detects if host device is a SPP or
MFi mode. This option is supported from KDC Bluetooth firmware version 2.2.O.
K
KDC User Manual SYNCHRONIZATION
5. Synchronization
When barcode data is collected, it must be uploaded to your application. KTSync, which is bundled
with the KDC, is a software that Enables barcode data to be uploaded to any PC, PDA, or smartphone
running Android 2.1+, Apple iOS3.1.3+, Blackberry,Mac and Windows XP/Vista/7/8/10/Mobile 5.0+.
It has three major functions. (Windows XP/Vista/7/8/10 version supports all of the following
features. Tablet, PDA and Smartphone versions support only limited features of PC KTSync.)
z Synchronization - Provides data upload functionality to your applications.
z Keyboard Emulator - Enables scanned data to be uploaded directly into your application as if
the data were being entered manually with a keyboard.
z Application Generation - Enables users to create custom applications or download predefined
applications such as Master-Slave, Pick/Bin, DB Lookup and Inventory.
Additional functions include:
Prefix and Suffix add-ons to eliminate manual data entry.
Symbology and Scan Option selections.
Barcode Wedging options.
KDC Menu configurations.
K
KDC User Manual SYNCHRONIZATION
5.1
KTSync Menu
KTSync was installed on your PC during the initial installation process. Before data may be uploaded
to any host device, KTSync must be launched on the host and configured to recognize the KDC. The
following screen displays when KTSync is launched:
File Menu
z Connect: This option displays the Serial port (COM#) assigned to KDC. You may also use this
option to manually assign the Serial port. The Serial port assigned to KDC may be found
under Windows Device Manager. The port assignment is used by KTSync for synchronizing
data from the KDC to the host.
z Synchronize: This option manually tells the KDC to synchronize data with the host. While
data is being synchronized, KTSync menu options are unavailable
Please do not use your computer during data synchronization.
z Bluetooth: This option is not available on KDC100/KDC500. Users may register a MAC
address to be directly connected by KDC20/30/200/250/300/270/350/400.
z Configuration: This option Enables users to set different KDCs with same settings by
exporting and importing settings from one KDC to the other.
z Exit: This option ends the KTSync program. You must re-run KTSync before you may
synchronize data on the KDC.
0QVG
Figure 17 - File Menu
Figure 16 - KTSync
®
Synchronizer Initial Screen
K
KDC User Manual SYNCHRONIZATION
Settings Menu
z Synchronization: Select Synchronize options.
z Barcode & KDC: Select Barcode and KDC options.
z Others: Select Auto Connection and/or Synchronization Confirmation options.
Application Menu(KDC500 doesn’t support Application)
z Generation: Create user application or download predefined application.
z DB Lookup: Enables users to download DB into KDC and display barcode description field.
z Master/Slave: The user defines a master barcode for comparison with one or more slave
barcodes.
z Pick/BIN: The user defines Pick ID and the barcode symbology for comparison with a
defined Bin.
z Inventory: Users may count inventories. Inventory description will be displayed if inventory
DB is downloaded into the KDC.
About Menu - KTSync - Version Information
Figure 20 - About Menu
Figure 18 – Setting Menu
Figure 19 - Application Menu
K
KDC User Manual SYNCHRONIZATION
5.2
File Menu
Connect to KDC
The KDC automatically connects to a COM port when connected to the PC’s USB port. If needed, the
user may manually assign the KDC COM port by using the KTSync Connection submenu under the
File menu.
z The COM port assignment is found in the Windows Device Manager.
z KTSync will not connect to the KDC if it is in the KDC Menus. You must EXIT from the
KDC Menus.
z If KTSync fails to connect automatically to the KDC, please follow these steps:
1. Exit KTSync.
2. Check to make sure that you have connected the KDC to a USB port on your PC.
3. Make sure that the user is using the cable provided with the KDC.
4. Check to make sure that the KDC is not in KDC Mode Menu.
5. Restart KTSync.
You may manually assign the COM port using KTSync Connect option under the File
menu.
Synchronize
Located under the File Menu, this option enables the user to manually synchronize data on KDC with
the host. This option is similar to clicking on the Synchronize button in the KoamTac Data
Synchronizer box.
Erase KDC Memory
Erase all stored data in the KDC internal memory.
Figure 21 - COM Port Selection for KDC
0QVG
K
KDC User Manual SYNCHRONIZATION
Bluetooth
This menu option enables the user to register up to ten Bluetooth devices, including their MAC
address, PIN #, and optional prefixes or suffixes. This option enables direct Bluetooth connection
between KDC and other Bluetooth devices, such as a Bluetooth printer. The user should choose a
Bluetooth device to be connected in “Connect to” menu in KDC Bluetooth Service menu.(KDC500
doesn’t support this feature)
Figure 22 - Bluetooth Device Registry
K
KDC User Manual SYNCHRONIZATION
Configuration
This menu is useful for the users who need to configure different KDCs with same settings. In this
menu, you may export settings from a KDC to your computer and import it to other KDCs.
When you select Configuration in File menu, you will need to choose either Export or Import. First,
select Export. You name the settings file, press Open, and it is exported to your computer. Second,
connect a different KDC to your computer and import the settings file to the KDC by selecting Import
in the Configuration menu. Once configuration has been finished, KDC will restart.
z Export
z Import
Figure 23 – Configuration
K
KDC User Manual SYNCHRONIZATION
Synchronization Settings
KTSync provides several synchronization options for synchronizing data from your KDC to host
devices.
Destination of Data
When barcode data is uploaded to the host device, you must assign a destination for the data.
Destination of Data options include:(This option is applied to only Windows XP/Vista/7/8/10)
z File - This option means data will be saved in the assigned filename. You may select a different
target directory by clicking the New icon. The default directory is C:\MyData\sn_timestamp.txt.
If this directory is not created, you will be prompted to create it before data may be uploaded to
a file.
z Active Window - This option means scanned barcode data is sent directly to the active program
running on your device as if the data is being entered directly from a keyboard.
z Microsoft Excel - This option means barcode data is being imported directly into Microsoft’s
Excel. Various parameters may be set when uploading data to Excel.
Figure 24 - KTSync Synchronization Settings
K
KDC User Manual SYNCHRONIZATION
z Select from Current Running Application – This option enables the user to select a currently
running application for data synchronization.
• Data synchronization begins immediately if “Automatically Synchronize after
Connection” is selected. If not selected, data synchronization is started manually
by the user.
• Users SHOULD NOT operate the PC during the synchronization process. It may
interrupt the process causing unreliable results.
Synchronization Methods
Fast Synchronization in Burst Mode
The KDC may synchronize data to a host device in Burst mode or Sequential mode. Burst mode
provides the fastest synchronization process but could result in error in a poor Bluetooth
environment. Fast synchronization in Burst mode is only recommended with USB connection.
Synchronize Normal Data
If Synchronize Normal Data option is selected, the KDC will synchronize only Normal Data in KDC
memory. If the user wants all data in KDC memory synchronized, the user should select Synchronize
Normal Data and Synchronize Application Data.
Synchronize Application Data
If Synchronize Application Data option is selected, the KDC will synchronize only Application Data in
KDC memory. If the user want all data in KDC memory synchronized, the user should select
Synchronize Normal Data and Synchronize Application Data.
Clear KDC Memory after Synchronization
If this option is selected, the stored barcode data is cleared from the KDC memory after
synchronization.
z It is important to clear the KDC memory periodically to prevent a Buffer Full message. Buffer
Full prevents the KDC from storing additional data. Stored barcode data may also be deleted
using the Reset Memory feature on the KDC.
Automatically Synchronize after Connection
0QVG
K
KDC User Manual SYNCHRONIZATION
This option lets the user automatically synchronize collected data immediately to the computer
when the KDC is connected to the host.
z IMPORTANT: Before selecting this option, remember to configure all options properly.
z Data synchronization may be done manually by clicking the synchronize icon if this option is
not selected.
Beep while Synchronization
The user may enable or disable the beep tone during the synchronization process. If this option is
selected, a beep is sounded every time barcode data is synchronized. The KDC beeps 5 times when
the synchronization process is complete.
Append Data to File
If the user has specified a file name and Append data to File option is enabled, KTSync will append
data to the existing file instead of creating a new file.
Current KDC Wedge Method
The KDC may be configured in one of five wedge/store modes:
z Wedge Only - Scanned data is transmitted to the host. The KDC does not store scanned
data.
z Wedge & Store - Scanned data is stored in the KDC and transmitted to the host.
z Store Only - Scanned data is stored in the KDC but NOT transmitted to the host.
z Save if Sent - Scanned data is stored in the KDC ONLY if transmission to the host is
successful.
z Save if Not Sent - Scanned data is stored in the KDC ONLY if transmission to the host is
unsuccessful.
Enable Wedge (Handheld Scanner Mode)
This option will be checked if Wedge Only or Wedge & Store option is selected.
Keep Scan Data in KDC
This option will be checked if Store Only or Wedge & Store option is selected.
K
KDC User Manual SYNCHRONIZATION
Synchronization Options
Synchronize KDC Time with PC Time when Connected
This option enables the user to synchronize the KDC date and time with the host date and time.
Synchronization of date and time occurs after the data is uploaded to the host device.
Delays
The user may set transmission delays between barcodes and characters during the synchronization
process. It is important to set proper delays to prevent errors during the transmission of collected
barcodes. Some Windows applications, such as Excel, require longer delay times.
Attachments
Timestamp, Barcode Type, and Serial Number may be attached to the scanned barcode by selecting
these options. The Serial Number of the KDC may be attached to the Start or End of Record.
Prefix and Suffix
z Enter the characters the user wants to attach to the front (Prefix) or back (Suffix) of the
barcode in the Prefix and Suffix fields.
z The character set is any combination of ASCII characters including alphanumeric, line feed
(“\n”), and carriage return (“\r”).
Order and Delimiter
z Select Order of Data – Type, Data, and Timestamp
z Select the Delimiter between Data – Tab, Space, Comma, and Semicolon
z Select the Delimiter between Records – None, LF, CR, Tab, and <LF & CR>
Application Options
Synchronize Non-Compliant Data
The KDC will synchronize both compliant and non-compliant data (filtered data) if Synchronize Non-
Compliant Data option is Enabled.
Consolidate Steps in One Record
KTSync will consolidate the data collected in Step 1 with the data collected in Step 2 and/or Step 3.
When Consolidate Steps in One Record is enabled, data will be consolidated into one record instead
of individual data records for each step. If this option is enabled, non-complete records, i.e. three
steps were defined but data was only collected for two steps, will be discarded.
Attach Quantity
If this option is enabled, quantity will be attached to the left or right of the data.
K
KDC User Manual SYNCHRONIZATION
5.3
Barcode & KDC Settings
KTSync enables the user to configure the KDC Scan Options and Barcode Settings. The configuration
options for the KDC using KTSync are similar to the Set Barcodes, Code Options, Data Editing and
Scan Options on the KDC Menu. Please refer to 11. Appendix A – Barcode & Scan Options for proper
barcode settings for the application.
The user must configure barcode and scan options properly for optimal KDC
performance.
0QVG
Figure 25 - Barcode & KDC Settings, Symbologies, Data Editing and Scan Options
K
KDC User Manual SYNCHRONIZATION
Select Symbologies and Symbology Options
The process for scanning and reading barcodes is delicate and complicated. Although your KDC is
equipped with a high performance scan engine, if configured incorrectly it may not perform at its
peak performance level. To ensure its high performance, the KDC comes configured to optimize its
scan engine technology. Unless you clearly understand the impact of your changes to the KDC
settings, please do not change factory default settings. Please refer to Appendix A for details.
Pressing the Default icon will reset all symbology related options to factory default settings.
Data Editing Option
Prefix - Enables the user to add a prefix to scanned data that may then be stored in KDC or wedged
to the host. The Prefix format must be defined in the data format menu of KTSync. The maximum
length for a Prefix is 11 characters.
This Prefix option is different from the Prefix option in KTSync that appends the prefix
to data during synchronization.
Suffix - Enables the user to add a suffix to scanned data, which may then be stored in KDC or wedged
to the host. The Suffix must be defined in the data format menu of KTSync. The maximum length for
a Suffix is 11 characters.
This Suffix option is different from the Suffix option in KTSync that appends the suffix to
data during synchronization.
AIM ID - Enables the user to add AIM ID to scanned data, which may then be stored in KDC or
wedged to the host. AIM ID must be defined in data format menu of KTSync. AIM ID is either added
to the end of Prefix or Suffix.
Partial Data: Enables the user to display and store partial data. The user defines the start position
and number of characters to be displayed and stored.
z Select the x characters from y position
¾ Set Partial Data Start Position to y, Partial Data Length to x, Partial Data Action to
Select.
¾ Partial Data Length 0 selects all characters from y position.
z Erase the x characters from y position
¾ Set Partial Data Start Position to y, Partial Data Length to x, Partial Data Action to
Erase.
¾ Partial Data Length 0 erases all characters from y position.
0QVG
0QVG
K
KDC User Manual SYNCHRONIZATION
5.4
Other Settings
Other options under the Settings menu allow the user to select four additional settings:
z Ask Confirmation before Trying Auto Connection prevents unintentional launch of
KTSync.
z Ask Confirmation before Starting Auto Synchronization prevents unintentional
synchronization of data.
z Minimize KTSync on Start will minimize KTSync and send it to the tray upon execution.
z Keep Checking Bluetooth Connection Enables reconnection of KDC once Bluetooth signal
is detected. This feature is useful when moving to or from Bluetooth host device
frequently. KTSync will automatically reconnect Bluetooth connection when the user
enter an effective Bluetooth network range. (Not Available on KDC100)
To select any of these settings, click on the box to the left of the setting. A check mark () will display
next to the setting to indicate that it is selected.
Figure 26 - KTSync
®
Confirmation Settings
K
KDC User Manual SYNCHRONIZATION
KDC Menu in KTSync
After connecting KDC to PC with a USB cable, run KTSync on your PC and you will see KDC Menu on
the right side of KTSync window. Click KDC Menu, and you may configure your KDC in KDC Menu
window, as shown below.
5.5
Mobile pKTSync
pKTSync provides limited functionality for Pocket PC 2003 and Mobile 5.0+ users.
1. Synchronization - Provides data upload functionality to your applications.
2. Keyboard Emulator - Enables scanned data to be uploaded directly into your application as if
the data were being entered manually on a keyboard.
Figure 27 - KDC Menu in KTSync
K
KDC User Manual SYNCHRONIZATION
For detailed explanations of these functions, please refer to earlier sections of this chapter.
WARNING: The user must assign the correct COM port to KDC before using pKTSync. Please refer
to the mobile device manual for details on Bluetooth pairing and COM port assignment methods.
Figure 28 - Mobile pKTSync
K
KDC User Manual SYNCHRONIZATION
5.6
Android aKTSync
The KTSync provides limited functionality of PC aKTSync to Android users.
x aKTSync only supports Android devices with 2.1+ OS version and that are compatible
with BluetoothChat application.
x KDC with Bluetooth Spec2.1+EDR doesn’t prompt Pin code entry menu.
KDC and Android Pairing
1. Pairing
z Select SPP Bluetooth profile from the KDC ConnectDevice submenu in BT Config menu.
z Search KDCxxx from Android and pair the two devices.
z If SPP2.0 is selected, KDCxxx PIN code is “0000”.
2. Connection
z Click Connect icon in aKTSync.
z Android will list paired Bluetooth devices and the user should select the target KDC.
3. Synchronization: Provides data upload functionality to the applications.
4. Settings: The user may change various Synchronization options in the settings menu.
5. Wedging: The user may wedge barcode data to any Android application. Press the home key
and launch the target application.
Launch KTSync
1. Download and install aKTSync from the Android Play Store.
2. Change KDC Bluetooth ConnectDevice option to SPP.
3. Execute Android Bluetooth device scan option and KDC Bluetooth pairing option.
A. Execute KDC Bluetooth Pairing option.
B. Launch Settings on the Android device.
C. Select Wireless and Networks.
D. Click on Bluetooth Settings.
E. Click on Scan devices.
F. The Android device will display the KDC model and 6 digits of the serial number.
4. Press the KDC list entry, enter “0000” PIN code, and press OK.
5. When paired, the Android device will display “Paired but not connected”.
6. Launch aKTSync program.
A. Press menu key and select the Connect option on the top left.
0QVG
K
KDC User Manual SYNCHRONIZATION
B. From the list of paired devices, choose the KDC to use.
C. On the top menu bar of aKTSync, you will see a message “connecting”, and then “connected”.
D. On the KDC display, you will see “Pairing Succeeded!!!” and then “Bluetooth Connected”.
E. Select Settings option on the bottom left to change KTSync setting.
Figure 29 - Android aKTSync
K
KDC User Manual SYNCHRONIZATION
Keyboard Wedge
1. Launch Settings on the Android device.
2. Select Language and Keyboard (or Input method).
3. Select KTSync Keyboard.
4. Launch the application and touch the input box to focus.
5. The barcode will be wedged to the input box upon scanning a barcode.
K
KDC User Manual SYNCHRONIZATION
5.7
iPad/iPhone/iPod Touch KTSync
The KTSync for iPad/iPhone/iPod touch provides limited functionality of PC KTSync for iPad, iPhone
and iPod touch users.
1. The KDC supports SPP and MFi Bluetooth profiles.
2. The iPhone/iPad/iPod touch should use MFi Bluetooth profiles. MFi is the default profile of
KDCi models.
3. Download the KTSync program from the App Store.
4. Enable the iPhone/iPad/iPod touch Bluetooth power from the Setting > General > Bluetooth
menu.
• Users have to disable MFi option in System > MFi menu to use HID Bluetooth
profiles.
• Users have to RESET the iPhone/iPad/iPod touch to change “HID to MFi mode” or
“vice versa” after removing previous KDC connection.
KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
KDC20i/30i/200i/250i/300i/270i/350i/400i/500i connection using MFi mode
1. Download and install iKTSync from the Apple App Store.
http://itunes.apple.com/us/app/ktsync/id372916602?mt=8
2. Press the two KDC side buttons simultaneously to enter menu mode.
3. Scroll down to Bluetooth menu using KDC Down button.
4. Press the front middle scan button.
5. Scroll down to Discovering and press the front middle scan button.
a. “Discovering Started …” message will be displayed on KDC screen.
b. Discovering will take about 30 seconds.
6. Select discovered iPhone/iPod touch device name and press the front middle scan button.
a. [Pin Code] User Default/Enter PinCode will be displayed.
b. Press the front middle scan button to select the Use Default option.
c. The message “Connecting to iPhone/iPod touch device name” will be displayed.
d. iPhone/iPad/iPod touch will ask for the PIN number.
f. Please enter “0000” and hit “connect” icon.
g.“iPhone/iPad Connected” message will be displayed.
7. Launch KTSync and configure Settings.
iKTSync Settings
iKTSync provides following Settings menu.
0QVG
K
KDC User Manual SYNCHRONIZATION
x Synchronization - The user may configure Synchronization options, such as destination of
data, data formation and delimiters.
x Other settings - Users may configure KDC350 GPS module, disconnection options and soft
trigger button.
x
How to Connect and Reconnect MFi Mode using UP Keys
1. The user needs to select the option to use this feature in the BT Config > BT Toggle.
2. Press the UP button to connect or reconnect to the iPhone/iPad/iPod touch.
Figure 30 - iPad/iPhone/iPod touch KTSync
K
KDC User Manual SYNCHRONIZATION
How to use Keyboard Wedge with iKTSync
1. Navigate to the iPhone/iPad/iPod Settings > General > Keyboard > Keyboards > Add New
Keyboard... > Select the KTSync keyboard to be added.
2. Select the KTSync Keyboard > Allow Full Access.
K
KDC User Manual SYNCHRONIZATION
3. Open up the application you want to scan into, and tap on the screen so the on-screen
keyboard appears. Tap and hold on the globe icon located to the left of the spacebar.
Select the KTSync Keyboard & begin scanning!
Note: The KDC must be connected to KTSync & the KTSync keyboard must be selected in order for
this to work.
K
KDC User Manual SYNCHRONIZATION
5.8
Blackberry bKTSync
The bKTSync provides limited functionality of PC KTSync for Blackberry users.
KDC with Bluetooth Spec2.1+EDR does not prompt Pin code entry menu.
1. Download and install bKTSync from the Blackberry App World.
http://appworld.blackberry.com/webstore/search/ktsync?lang=en
2. Go to Blackberry Options > Applications menu and enable Input Simulation option.
3. Change KDC Bluetooth profile in ConnectDevice option to SPP.
4. Execute Blackberry Bluetooth manager and KDC Bluetooth pairing option:
A. Execute KDC Bluetooth Pairing option.
B. Launch the Blackberry Bluetooth manager and select “Search”. The KDC model and 6 digits of
the serial number will be displayed.
C. Highlight the KDC and press the Enter or Select Key.
D. Enter “0000” PIN code and press the Enter or Select Key.
E. The Blackberry will display “Pairing with KDC” and then”complete.”
F. Close the Blackberry Bluetooth manager.
5. Go to Downloads folder and execute KTSync.
6. The user may configure KDC options in KDC settings and Symbologies Settings menu.
7. Go to KTSync Synchronization Settings and select Destination. To send collected barcode data as an
email attachment, choose Email Attachment as destination and enter in the email address, subject,
and body message that the user want to send. The user may enter multiple email addresses using
the semicolon (;) separator.
8. To scan barcodes into any application (like email, notes, worksheet or web browser), press the menu key
and select Running in the background option. bKTSync will maintain the connection and place the
scanned barcode data wherever the cursor is flashing.
0QVG
K
KDC User Manual SYNCHRONIZATION
Figure 31 - Blackberry bKTSync
K
KDC User Manual SYNCHRONIZATION
5.9
KTSync for Mac OS X
The KTSync Mac OS X version provides limited functionality of PC Windows KTSync for Mac OS X
users.
x KTSync for Mac OS X version supports both Bluetooth SPP profile and USB connection.
The user should pair KDC with Mac before using the KTSync program via Bluetooth
connection.
x Mac OS X version KTSync is built as a X86 binary application and works with the Intel-
based Mac. It is verified on Mac PC running Mac OS X 10.6.5 and later versions.
KTSync Mac OS X version supports the following features:
9 Keyboard wedge function to a file, internal viewer, active window, and user application.
9 Synchronization to a file, internal viewer, active window, and user application.
9 Automatic connection and disconnection on USB port.
The user will see the following initial KTSync screen upon launching the program. KTSync will
connect automatically if KDC is plugged in a USB port or if KDC is paired.
Connect Button
The user may connect the Mac with the KDC that is paired or plugged into the USB
port by clicking the Connect button. The following screen will be displayed when this
button is pressed, and KTSync will start to connect to the selected KDC.
Disconnect Button
KTSync changes Connect button to Disconnect button once the KDC is connected.
The user may disconnect the KDC manually by selecting connected KDC on the
following screen.
0QVG
K
KDC User Manual SYNCHRONIZATION
Synchronize Button
The user may start the synchronization process by pressing the Synchronize button. The user may
select the destination of barcode data in the settings menu. There are 4 selectable
destinations: File, Internal viewer, Active window, and User application.
Clear Button
The user may press this button to clear the KTSync internal viewer.
Settings Button
The user may configure synchronization options on the following screen by
pressing the Settings button.
Destination of Data
The KTSync program wedges or downloads barcode data to one of the following four
destinations:
K
KDC User Manual SYNCHRONIZATION
z File: The KTSync makes a file name based on 3.11 if file name is specified as an
“sn_timestamp.txt”. The default directory is /Users/Shared/KTSyncData directory. The
user may define another directory or another filename by clicking the “New” button. The
maximum file path length is 128 characters.
z Internal Viewer: The KTSync displays barcode data in KTSync internal text viewer.
z Active Window: The KTSync sends barcode data to current active window if Active window
option is selected.
z User Application: The user may define the target application by pressing the “New” button.
The maximum application name path length is 128 characters.
Synchronization Options
z Synchronize KDC Clock
KTSync will set the KDC’s date and time with Mac PC date and time when the KDC is
connected to Mac, if this option is enabled.
z Burst Synchronization
KTSync will synchronize barcode data from KDC in burst mode. Otherwise, KTSync would
synchronize barcode data one by one. This option is enabled by default and maynot be
disabled.
z Synchronization on Connection
KTSync will automatically synchronize barcode data from the KDC when the KDC is
connected, if this option is enabled.
z Clear KDC Memory After Synchronization
KTSync clears barcode data stored in the KDC’s memory once synchronization has finished,
if this option is enabled.
z Append Data to File
KTSync appends synchronized data to existing file specified on destination. If file does not
exist then KTSync creates a new file.
Data Edition
z Attach Serial Number
The KTSync will add a KDC serial number to barcode data. This option is enabled by default
and maynot be disabled.
z Attach Time Stamp
The KTSync would add timestamp to barcode data. This option is enabled by default and
maynot be disabled.
z Attached Barcode Type
The KTSync would add barcode type to barcode data. This option is enabled by default and
maynot be disabled.
K
KDC User Manual SYNCHRONIZATION
z Serial Number
When Attach serial number is enabled, this option determines when to attach serial
number. “Start of record” means to attach at the front of record and “End of record”
means to attach to the end of record.
z Data Order
This option specifies the order of data (Barcode Type, Barcode Data and Timestamp) in the
record.
z Data Delimiter
This option is used to select a character to be added between barcode data, serial number
and timestamp and/or barcode type. User may select one of the following: None, Tab,
Space, Comma and Semicolon as the data delimiter. The Comma is selected as the data
delimiter by default.
z Record Delimiter
This option is used to select a character to be added at the end of the barcode record. The
user may select one of None, CR, LF, TAB, and CR&LF as the record delimiter. The CR&LF is
selected as the record delimiter by default.
Other Options
z Non-English Keyboard
This option is used when the barcode data has non-English characters and a non-English
keyboard.
6. Application Generation
KDC FW2.85 does not support the Application Generation feature. Users should
upgrade FW2.85 to FW2.86 or FW3.0+ to use Application Generation feature.
When you select the Application menu from the KTSync, the user may choose from the following five
Applications: Generation, DB Lookup, Master/Slave, Pick/BIN, and Inventory. Users may also
download saved programs using the Import & Download option.
When the Application tool is selected, the KDC will beep once to acknowledge a connection between
the KDC and the Application tool. The following KTSync warning window will pop up if the
downloaded application in KDC does not match with KTSync application tool.
KDC will wedge barcode data to the host in application mode if “wedge and store always”
option in data process menu is selected and KDC firmware version is higher than
2.86.xxx.G or 3.0+.
6.1
Application Generation
KDC Application Generation tool is a robust feature that enables the user to create custom
applications for collecting and managing barcode data. To create a custom application, select the
Generation submenu from the Application menu in KTSync®.
0QVG
0QVG
Figure 32 - Application Menu
Figure 33 - Application Warning Window
Generate Application
Generate step 1 - To generate a custom application, click on the Generate Step 1 box. This enables
the user to define the user prompts and data collection settings for Step 1 of the custom
application. Below is a description of each field. These prompts are the same when selecting
Generate step 2 and Generate step 3.
The custom application may include only Step 1.
z First line
Enter up to 13 characters; these will display on the first line of the KDC.
z Second line
Enter up to 13 characters; these will display on the second line of the KDC.
z Starting quantity
Enter a predefined start quantity for each scanned barcode. The start quantity may be
defined from 1 to 128. Use the up or down side key to choose the desired quantity.
z Waiting to scan
Enter the number of seconds the KDC pauses before the user prompts display. During
this timeout period, the user may modify the quantity. If this field is set to zero, the
Figure 34 - Application Generation Menu
0QVG
quantity field may not be adjusted. This field may be defined from “-1” to “30” seconds.
“-1” second enables infinite waiting of user quantity input.
z Enable data filter
Check this box to enable the data filtering option. Data filtering enables the user to
predefine different aspects of the barcode data the user are collecting.
Data Filter Settings
When the user select Enable data filtering, the user must click on the Settings button to select the
Data filter setting. The options for the Data filter settings are the same for Step1, Step 2, and Step 3.
z
Barcode Type
This field enables the user to select the type of barcodes the KDC will collect. When the user
clicks on the box, Select Symbols is enabled. A listing of the symbologies supported by the
KDC will display. To select a barcode symbology, click on the box associated with the
symbology.
z Minimum Data Length
This field enables the user to define the minimum length of the scanned barcode. The length
may be between 2 and 36 (1D models), 2 and 48 (2D models) characters. If the user scans a
barcode that has a length of less than the defined length, the barcode data is not collected.
Figure 35 - Data Filter Settings
The default KDC minimum barcode length defined in scan option is 4. Therefore,
users should change KDC minimum barcode length to 2 or 3 to define minimum
data length to 2 or 3.
z Maximum Data Length
This field enables the user to define the maximum length of a scanned barcode. The defined
length may be between 2 and 256 characters. If the user scans a barcode that has a length is
greater than the defined length, the barcode data is not collected.
z Barcode Collation
This option enables the user to define a data string that the KDC will use to compare
scanned barcodes.
¾ Starting Position – This is the start position of the scanned barcode data to be
compared with the defined data string.
¾ Data String – This is the defined value to be compared with scanned barcode data.
This value may be up to 32 characters.
z Collect Partial Data
This option enables the user to define partial barcode data to be collected when a barcode is
scanned. Only the partial data will be stored in the KDC.
¾ Start position – This is the starting position that the KDC will use when collecting
scanned barcode data.
¾ Data Length – This is the length of partial data to be stored by the KDC.
z Check for Duplicated Data
This option enables the user to prevent the collection of duplicate data.
¾ Previous Scanned Data – This option enables the user to compare the scanned
barcode with the previously scanned barcode and treat it as non-compliant data if
the user scanned the same barcode twice.
¾ All Stored Data – This option enables the user to compare the scanned barcode
with stored barcode data and treat it as non-compliant data if the same barcode
already scanned and stored.
0QVG
z Do not Save Non-Compliant Data
This field tells the KDC how to manage non-compliant data based on the defined data
filtering fields. If this field is enabled, non-compliant data is NOT stored in the KDC. If this
option is not enabled, non-compliant data is stored.
Generate step 2
To include another step in the data collection process, click the box, Generate step 2. This step has
the same options as Step 1. In this step, the user have the option of repeating step 2 by clicking the
box, Repeat Step.
This field is disabled when the application has three steps.
Generate step 3
To include a third step, click the box, Generate step 3. This step has the same options as step 1 and
2. In this step, the user has the option to repeat steps 2 or 3.
Application Download and Execution
Before running your application, it must be downloaded to KDC.
1. Click the “Download” icon from Application Generation Window.
2. Change KDC from Normal mode to Application mode.
A. Press two side buttons simultaneously to enter menu mode.
B. Select KDC mode and enter scan button.
C. Change to Application mode.
D. Save and exit from menu mode.
3. KDC will run in normal mode if you do not change to Application mode after
downloading the application.
4. If you want to delete the downloaded application in your KDC, select App. Data in
Reset Memory after you go to System Config in KDC Menu.
0QVG
6.2
Predefined Applications
KTSync provides four Predefined Applications: Master/Slave, Pick/Bin, DB Lookup and Inventory.
Master/Slave
Master/Slave predefined application enables you to define a master barcode for comparison with
one or more slave barcodes. The predefined application may be run once or continuously. Within
either setting, you may define a substring for comparison of master and slave barcodes.
Master/Slave Onetime
Define one master barcode and compare it with one slave barcode.
Master/Slave Continuous
Define one master barcode and compare it with multiple slave barcodes.
Collation Options
Works in either Onetime or Continuous Mode to compare a substring within the master and slave
barcodes.
z Master start position - Select the numeric position of start substring character in Pick
barcode, 1 to 255.
z Slave start position - Select the numeric position of start substring character in Pick
barcode, 1 to 255.
z Comparing Barcode Length - Number of characters to be compared, 0 to 255. 0 means all
characters.
Pick/Bin
The Pick/Bin predefined application is a special version of the Master/Slave predefined application.
The Pick/Bin application enables you to define the Pick ID and the barcode symbology for
comparison with a defined Bin.
Figure 36 - Master/Slave Application Settings
z Number of ID and Symbology
Define Pick ID characters from 1 to 32 and the barcode symbology.
z Pick Start Position and Symbology
Select numeric position of start substring character in Pick barcode from 1 to 255 and
the barcode symbology.
z Bin Start Position and Symbology
Select the numeric position of start substring character in Bin barcode from 1 to 255
and the barcode symbology.
z Comparing Barcode Length
Figure 37 - Master/Slave Application Flow Chart
%QNNCVKQP
%QNNCVKQP
'HILQHVXEVWULQJWR
HIL
Q
LQ
QHV
XEVW
UL
Q
J
EHFRPSDUHG
J
J
G
EHFRPSDUHG
HF
RPSD
UH
H
G
'HIDXOWLVHQWLUH
D
XOW
LVH
Q
D
XOW
LV H
Q
EDUFRGH
6FDQ0DVWHU
FDQ
0DV
W
%DUFRGH
6FDQ0DVWHU
FDQ
0DVW
%DUFRGH
2QHWLPH
&RQWLQXRXV
5GNGEV/5/QFG
GE
EV/5/Q
2QHWLPH
Q
Q
H
2QHW
LPH
H
&RQWLQXRXV
6FDQ&KHFN
FDQ
&KH
F
%DUFRGH
.'&0RGH
8SRU'RZQ
R
U
'
.H\
'
"
0LVPDWFKHG
0DWFKHG
8S
8S
.H\
'RZQ
'RZ
.H\
6FDQ&KHFN
FDQ
&KH
F
%DUFRGH
8SRU'RZQ
R
U
'
.H\
'
"
0DWFKHG
0LVPDWFKHG
8S.H\
"
1R
<HV
'RZQ
'RZ
.H\
8S
8S
.H\
Select the number of characters to be compared from 0 to 255. 0 means all characters.
Figure 38 - Pick/BIN Application Menu
User ID
Defined Scan User ID Valid User ID
Store User ID
Please
scan Pick data
User Input
Valid Barcode
Please scan
Bin data
User Input
Barcode
Match?
No
Yes
Yes
No
Up
Side Key
Scan button
Yes
No
Up
Side Key
Scan button
Yes
No
Ignore Scanned
Pick Label
Timeout
Ignore Scanned
Pick Label
Store
User ID,
KDC Serial Number,
Timestamp,
Pick Barcode
Exit to KDC Menu <Up>+<Down>
Figure 39 - Pick/BIN Application Flow Chart
DB Lookup Application
The DB Lookup application enables the user to download a database to the KDC that may then be
utilized for advanced AUTO-ID applications, such as displaying additional data after scanning a
barcode. For example, using our DB Lookup application, you may download a product database
including information such as description, price, and stock quantity. With the advanced data
functionality built-in to the KDC, you may easily display product price, description, and stock level
after the product’s barcode is scanned.
Functionality of DB Lookup Application (based on the firmware version v2.86 and v3.0+)
z The database size may not exceed 800 records (v2.86) / 61,440 records (v3.0+).
z The maximum record size is 128 bytes.
z Each record may have up to 4 fields, including the barcode, which is the primary key.
z The maximum field size is 39 characters.
z Quantities may be entered by pressing the UP or DOWN scroll buttons after DB fields are
displayed.
z Quantity may be 1 to 128.
z The user may create a database using Microsoft Excel.
1. Excel file must be saved as .txt.
2. Records should be separated by CR/LF.
3. Fields should be separated by TAB.
4. Database should end with CR/LF.
5. Last 4 bytes of database should be CR/LF/CR/LF.
DB Lookup Fields and Settings (based on the firmware version v2.86 and v3.0+)
z Download DB to KDC - Downloads user created database to KDC.
z Starting Quantity - Enter predefined start quantity for each scanned barcode. The start
quantity may be defined from 1 to 128 and may be adjusted using UP or DOWN buttons.
z Barcode Field - Select the position of barcode field in database from 1 to 4.
z Stored Barcode Start Position - Select the numeric position of start substring character of
barcode in database from 1 to 39.
z Scanned Barcode Start Position - Select the numeric position of start substring character of
scanned barcode from 1 to 39.
z Comparing Barcode Length - Number of characters to be compared from 0 to 255 where 0
is all characters.
z Display on KDC - Define database fields to be displayed on KDC. KDC may display one to
three fields. KDC will display one field in two or three lines, if same field is specified in line
entering option.
Inventory Application
The Inventory application enables the user to count inventories by scanning inventory barcodes.
This application will increase inventory item count if the same item is scanned. Users may also
download an inventory database to the KDC. If inventory DB is downloaded, KDC will display
inventory description.
Functionality of Inventory Application (based on the firmware version v2.86 and v3.0+)
z The inventory may not exceed 800 items (v2.86) / 61,440 items (v3.0+).
z The maximum record size is 128 bytes.
z Each record may have up to 4 fields, including the barcode, which is the primary key.
z The maximum field size is 39 characters.
z Quantities 1 to 32786 may be entered by pressing the UP or DOWN buttons after inventory is
scanned.
z Starting Quantity may be 1 to 128.
z Min/Max. Data Length is between 2 to 256 (1D models) or 4 to 256 (2D models).
z Barcode Collation Start Position is between 1 to 256.
z The length of Collation Data String is between 1 to 30.
Figure 40 - DB Lookup Application Menu
z Collect Partial Data Start Position is between 1 to 256.
z Collect Partial Data Length is between 1 to 256.
z Users may create an inventory database using Microsoft Excel.
¾ Excel file must be saved as .txt.
¾ Click User Inventory DB option to display inventory description.
¾ Click Do not add non-existing item into DB if one do not wish to add new items into
inventory DB.
¾ The number of Barcode Data Field is between 1 to 4.
¾ The position of Display Filed is between 1 to 4.
7. Troubleshooting
Figure 41 – Inventory Application
ISSUE
CAUSE
SOLUTION
KDC not working
Dead battery
z
Charge battery by connecting KDC to
your PC using the included cable
Hardware
failure
z
Contact distributor for technical
support
KDC not charging
Bad battery
z
Replace battery – Contact Local
Distributor
Poor USB port
z
USB port doesn’t supply proper
current to KDC
- Charge KDC using a different USB
port on your PC
Failed reading
Damaged
barcode
z
Scan a different barcode
Out of scan
range
z
Move the scanner closer to barcode
z Move scanner farther from the
barcode
Incorrect angle
z
Change the angle of scanner to
barcode
Symbology
not
supported
z
Contact KOAMTAC -
www.KOAMTAC.com for possibility of
custom symbology support
Scan options
z
Check scan option settings
Dirty scan
window
z
Clean scan window
Damaged scan
window
z
Replace scan window
KDC reads
wrong barcode
Dirty scan
window
z
Clean scan window
Damaged scan
window
z
Replace scan window
Poor quality
barcode
z
Select only necessary barcodes
z Increase minimum barcode length
z
Increase security level
Can’t communicate
with PC, PDA,
or smartphone
USB cable is not
connected
properly
z
Check cable connection between
KDC and host device
Software is not
working
properly
z
Reload the software
COM
configuration
z
Check COM port configurations
LED blinks yellow
Low battery
power
z
Charge the battery by connecting KDC
to PC.
z KDC will lose collected data if the
battery is empty.
Buffer Full Message
Full Memory
z
Clear the Memory using
Synchronization program
Empty Battery
Message
Empty battery
z
Connect USB immediately.
z Synchronize the collected data and
charge KDC
Abnormal KTSync
Operation on
DELL PC
Quickset Utility
z
Disable Quickset Utility before using
KTSync.
z Dell Quickset utility interrupts
normal KTSync operation
WSED Utility
z
Disable WSED Wireless enable/disable
utility
z delete the folder C:\Program
Files\WSED, which contains a file
WSED.exe, with the same icon as in the
taskbar
z Delete the registry entry
KEY_LOCAL_MACHINE
\SOFTWARE\Microsoft\Windows\Curr
entVersion\Run\WSED
Touch Keypad not
working
(KDC500)
Foreign Object
detected
z
Clear any foreign object (including your
finger) placed on the touch keypad and
reset KDC.
Hardware
failure
z
Contact distributor for technical
support
Compromise Message
displayed
(KDC500)
Security Attack
detected
z
Contact distributor for technical
support
Table 6 - Troubleshooting Techniques
8. Warranty
LIMITED WARRANTY AND DISCLAIMERS
BY OPENING THE PACKAGE OF THIS PRODUCT YOU AGREE TO BECOME BOUND BY THE LIABILITY AND
WARRANTY CONDITIONS AS DESCRIBED BELOW.
UNDER ALL CIRCUMSTANCES, THIS MANUAL SHOULD BE READ ATTENTIVELY, BEFORE INSTALLING AND OR
USING THE PRODUCT.
Serial Number
A serial number appears on the KDC label. This official registration number is strictly related to the device
purchased. Make sure that the serial number appearing on your KDC is not removed. Removing the serial
number will affect the warranty conditions and liability disadvantageously, so please maintain the label with
serial number on the KDC. Units with the serial number label removed should not be operated.
Warranty/Warranty Period/Liability
KOAMTAC, Inc. (“KOAMTAC”) manufactures its hardware products in accordance with industry-standard
practices. Unless otherwise agreed in a contract, KDC is warranted for a period of one year after purchase,
covering defects in material and workmanship except rechargeable battery. KOAMTAC will repair or, at its
opinion, replace products that prove to be defective in material or workmanship under proper use during the
warranty period. KOAMTAC will not be liable in cases (i) in which the unit has been repaired or altered unless
done or approved by KOAMTAC, (ii) in which the unit has not been maintained in accordance with any
operating or handling instructions supplied by KOAMTAC, (iii) in which the unit has been subjected to unusual
physical or electrical stress, misuse, abuse, power shortage, negligence or accident or (iv) in which the unit has
been used other than in accordance with the product operating and handling instructions. Preventive
maintenance is the responsibility of the customer and is not covered under this warranty. Under no circumstance
will KOAMTAC be liable for any direct, indirect, consequential or incidental damages arising out of use or inability
to use either the hardware or software, even if KOAMTAC has been informed about the possibility of such
damages.
Warranty Coverage and Procedure
During the warranty period, KOAMTAC will repair or replace defective products returned to KOAMTAC
warehouse. International customers should contact the local KOAMTAC office or support center. If warranty
service is required, KOAMTAC will issue a Return Material Authorization Number. Products must be shipped in
the original or comparable package, shipping and insurance charges prepaid. KOAMTAC will ship the repaired
or replacement product freight and insurance prepaid. Customer accepts full responsibility for its software and
data including the appropriate backup thereof. Repair or replacement of a product during warranty will not
extend the original warranty term.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
CORPORATE HEADQUARTERS
116 Village Blvd., Suite 305
Princeton, NJ 08540, USA
Phone: 609-256-4700, FAX: 609-228-4373
Email: support@koamtac.com
For more information, visit our website - www.koamtac.com
9. Contact Information
BARCODE & SCAN OPTIONS
10. Appendix A – Barcode & Scan Options
The process for scanning and reading barcodes is delicate and complicated. Although the KDC is
equipped with a high performance scan engine, if configured incorrectly, it may not perform at its
peak performance level. To ensure its high performance, the KDC comes configured to optimize its
scan engine technology. Unless you clearly understand the impact of your changes to the KDC
settings, please do not change factory default settings.
10.1
Symbologies
KOAMTAC’s KDC products support most major barcode symbologies including 1D, 2D, Postal, and
OCR-Fonts. Below is the list of the barcode symbologies supported by the KDC with respect to each
model’s particular area of support. To ensure superior scan performance, remember to select only
the required symbologies.
KDC20/100/200/250/270L/350L/
410
/411/415/470L/500L
KDC30/300/270C/350C/420/421/425
/450
/470C/500C
1D
Barcodes
EAN13, EAN8, UPCA, UPCE, Bookland
EAN, EAN13
with Addon, EAN8 with
Add
-on, UPCA with Add-on, UPCE
with
Add
-on, Interleave 2 of 5, ITF14,
Code128, Codabar, GS1
-128, Code39,
Code93, & Code35
Codabar, Code11, Code32, Code39,
Code128
, EAN8, EAN13, GS1-128, I2of5,
MSI, Plessey, PosiCode, GS1 DATABAR
OMNI, GS1 Limited, GS1 Expanded,
S2of5IA, S2of5ID, TLC39, Telepen,
Trioptic, UPCA, & UPCE
2D
Barcodes
N/A
AztecCode, AztecRunes, CodablockF,Code
16K, Code49, DataMatrix, MaxiCode,
MicroPDF, PD
F417, & QRCode and
HanXin Code
Postal
Barcodes
N/A
AusPost, MayadaPost, ChinaPost,
JapanPost, KoreaPost, KixPost, Planet
Code, Postnet (US), & UKPost
OCR
Fonts
N/A
OCR-A, OCR-B, OCRUSCurrency,
OCRMICRE13B, & OCRSEMIFONT
Bookland EAN vs. EAN-13
Bookland EAN, which includes ISBN, ISSN, and ISMN, is supported by the KDC. This group of
symbologies is essentially an EAN-13 barcode with fixed prefixes; 977 for ISSN, 978 for ISBN, and 979
for ISMN. If EAN-13 and Bookland EAN are both enabled, Bookland EAN takes precedence. Bookland
Table 7 - Symbologies Supported by KDC
BARCODE & SCAN OPTIONS
EAN does not have any options. The Bookland EAN barcode does not contain any groupings – that is,
there are no hyphens or separators. Thus, the ISBN 957-630-239-0 is transmitted as 9576302390.
Add-on Symbologies
By default, the 2 or 5 digit add-on symbols with a UPCE, UPCA, EAN-8, and EAN-13 barcode are
neither decoded nor transmitted. Transmission for these specific symbologies is enabled by setting
the appropriate withAddon options. There are 4 withAddon options, one for each symbology:
UPCEwithAddon
UPCAwithAddon
EAN8withAddon
EAN13withAddon
The decoding of add-on symbols are defined by the following table, which explains the process for
EAN-13 symbols.
The add-on symbol is appended to the EAN-13 barcode. The process is similar for UPCE, UPCA, and
EAN-8 barcodes. Note that all the UPCE, UPCA, EAN-8, and EAN-13 formatting and conversion
options are in effect. The following table should help explain the effect of various options for EAN-8
barcode 12345670 + 12.
Barcode
EAN8_as_EAN13 EAN8
_ReturnC
heckDigit
EAN13
_ReturnChec
kDigit
1234567012
False True N/A
123456712
False
00000123456712
True N/A False
Mode Behavior Value of flags
Auto
-
discrimination
If add
-on symbol is present, then it is also
decoded; otherwise, only the EAN
-
13 symbol
is decoded.
true true
With add
-on
Only EAN
-13 barcodes with 2 or 5 add-on
symbols are decoded.
false true
Without add
-on
The add
-on symbol is ignored. true false
Table 8 - Add-on for EAN-13 Symbology
BARCODE & SCAN OPTIONS
000001234567012
True
The add-on symbol contains neither a check digit nor a terminating guard band. Every effort has
been made to reduce the decoding error; however, it is likely to decode a partial scan of a 5-digit
add-on symbol as a 2-digit add-on symbol. It is strongly recommended that the minimum security
level be set at 2 while decoding add-on symbols. Since the decoder takes a conservative view on the
add-on symbols, it is likely that the add-on symbol will be missed in the auto-discrimination mode.
Auto-discrimination mode should then be avoided.
10.2
Code Options
(KDC20/100/200/250/270L/410/411/415/470L)
The KDC supports the following barcode options:
z Transmission of start and stop characters
z Reverse direction
z Symbology conversion
z Verification of optional check character
z Transmission of check digit
z Transmission of Start and Stop Characters
For Codabar symbols, the user may choose not to transmit the start and stop symbols, the NOTIS
Editing. By default, they are transmitted. Setting the field CodaBar_NoStartStopChars to true
disables the transmission.
Reverse Direction
This option may be selected if direction oriented symbologies are designated, such as Code35.
Symbology Conversion
By default the EAN-8, UPCE, and UPCA symbols are transmitted in their native format. However,
it is possible to show them in a different format. The user may choose to display UPCE symbols as
either UPC-A or EAN-13 symbols, EAN-8 symbols as EAN-13 symbols, or UPC-A symbols as EAN-13
symbols. The following table shows the effect of setting various options.
Option EAN-8 UPC-A UPC-E All others
Table 9 - Add-on for EAN-8 Symbology
BARCODE & SCAN OPTIONS
EAN8
_as_EAN13
Converted to
EAN
-13
No effect
No effect
No effect
UPCA
_as_EAN13
No effect
Converted to
EAN
-13
No effect
UPCE
_as_EAN13
No effect
No effect
Converted to
EAN
-13
UPCE
_as_UPCA
No effect
No effect
Converted to
UPC
-A
Verification of Optional “Check Digit”
Code39 and Interleave 2 of 5 have an optional check digit, which, by default, is not verified.
Changing the option VerifyCheckDigit to true may enable their verification, or the user may enable
the verification for individual symbologies. If the check digit verification fails, the barcode is not
transmitted.
Transmission of “Check Digit”
By default, the check digit – optional or mandatory – is not transmitted. Its transmission may be
enabled for all symbologies by enabling ReturnCheckDigit option.
Option Selected
Is the check digit returned?
ReturnCheckDigit
Yes
Yes
Yes
Yes
Yes
Yes
Table 10 - Symbology Conversion
Option Selected Verify Code39 check digit
Verify I2of5 check digit
VerifyCheckDigit
Yes
Yes
Code39_VerifyCheckDigit
Yes
No effect
I2of5
_VerifyCheckDigit
No effect
Yes
Table 11 - Verification of Optional "Check Digit"
BARCODE & SCAN OPTIONS
EAN13_ReturnCheckDigit
Yes
No
effect
No
effect
No
effect
No effect
No
effect
EAN8_ReturnCheckDigit
No
effect
Yes
No
effect
No
effect
No effect
No
effect
UPCA_ReturnCheckDigit
No
effect
No
effect
Yes
No
effect
No effect
No
effect
UPCE_ReturnCheckDigit
No
effect
No
effect
No
effect
Yes
No effect
No
effect
Code39_ReturnCheckDigit
No
effect
No
effect
No
effect
No
effect
Yes
No
effect
I2of5_ReturnCheckDigit
No
effect
No
effect
No
effect
No
effect
No effect
Yes
Resolution of Inconsistencies
Three types of inconsistencies could arise in the assignment of symbology options. The decoder has
pre-defined strategies to resolve these inconsistencies: If UPCE_as_EAN13 is true, then
UPCE_as_UPCA is ignored.
If symbology conversion is selected but the target symbology is not enabled, then the decoder still
outputs the symbol in the target symbology. For example, suppose UPC-E is enabled and
UPCE_as_EAN13 is true but EAN-13 is disabled. All UPC-E symbols will be shown as EAN-13 and EAN-
13 options (if specified) will be applied. For the two symbologies that have optional check digits,
Code39 and Interleave 2 of 5, the decoder will always transmit the check digit if the verification is
disabled.
Verify Check
Digit
Return Check Digit
Description
Disabled Enabled or
Disabled
Check digit is not verified but is transmitted
Enabled Disabled Check digit is verified but is not transmitted
Enabled Enabled Check digit is verified and is transmitted
Table 12 - Transmission of "Check Digit"
Table 13 - Resolution of Inconsistencies
BARCODE & SCAN OPTIONS
10.3
Miscellaneous Barcode Information
Height of a Linear Barcode
Industry standards suggest a height of either 6.5mm or 15% of the symbol length, whichever is
greater. Symbols of less than recommended heights may cause recognition problems.
Check Characters
Yes, we recommend the use of check-characters in barcodes. Operating without check-characters is
not safe and will lead to errors that are costly to correct. Using check-characters positively affects
data integrity, especially when character density is at the limits and/or image quality is not at its
best.
Prevent Interleave 2 of 5 Partial Reading
A partial scan of an Interleave 2 of 5 symbols may decode and cause incorrect data to be read. To
prevent partial scans on long symbols, the user should include bearer bars. These bars run along the
top and bottom edges of the barcode in the scanning direction. If a partial scan of the barcode
occurs, the scanning beam will hit the bearer bar and will not decode. The bearer bar must touch the
top and bottom of all the bars and must be at least 3 times as wide.
Another solution for the short scanning problem is to fix all Interleave 2 of 5 symbols to a set
number of digits. Zeros may be used to pad the data to the set number of digits. The application
program would then be set to only accept scans of the correct number of digits.
Finally, a check digit may be used. The Interleave 2 of 5 symbology has an optional check character
that uses a weighted Modulo 10 scheme. The check character is the last character in the symbol and
should be checked by the decoder and then transmitted with the data. Since Interleave 2 of 5 must
always have an even number of digits, the leftmost character may need to be a zero when the check
character is added. The standard check digit is calculated by assigning alternating 3,1,3,1… weights
to respective data digits. These weights are then multiplied by their respective data digits and the
products are summed. The check digit is the digit that needs to be added to the sum to make it an
even multiple of 10. An example would be if the sum of the products was 37, then the check digit
would be 3.
Equation to Determining Potential Number of Stored Barcodes
The number of barcodes that may be stored in the KDC memory depends on the size of the barcodes.
Example: In case of EAN-13, it takes up 20 bytes. The maximum number of EAN-13 barcodes that
may be saved is STORAGE_SIZE/20. For example, in case of 4MB, it may store maximum 204,800
barcodes and in case of 8MB, it may store maximum 409,600 barcodes.
BARCODE & SCAN OPTIONS
Data Buffer Full
When the data buffer is full, the KDC displays a message, Buffer Full, ignoring any command to scan
barcodes. The user must reset the data buffer to continue data collection.
K
KDC User Manual FAQ
11. Appendix B –FAQ
11.1
Symbology
Q: What barcode symbologies are supported by the KDC?
A: The KDC20/100/200/250/270L/350L/410/411/415/470L/500L support 1D barcode only.
KDC30/300/270C/350C/420/421/425/450/470C/500C support most major 1D, 2D barcode
symbologies and OCR.
Table 15 – Symbologies supported by KDC
-&%
%%
%%
&$CTEQFGU
$]WHF&RGH$]WHF5XQHV&RGDEORFN)
&RGH.&RGH'DWD0DWUL[
0D[L&RGH0LFUR3')3')
45&RGHDQG+DQ;LQ&RGH
&$CTEQFGU
&RGDEDU&RGH&RGH&RGH
&RGH($1($1*6
,RI06,3OHVVH\3RVL&RGH*6
'$7$%$5201,*6/LPLWHG*6
([SDQGHG6RI,$6RI,'7/&
7HOHSHQ7ULRSWLF83&$DQG83&(
2QUVCN$CTEQFGU
$XV3RVW&DQDGD3RVW&KLQD3RVW
-DSDQ3RVW.RUHD3RVW.L[3RVW3ODQHW
&RGH3RVWQHW86DQG8.3RVW
1%4(QPVU
2&5$2&5%2&53DVVSRUW
Table 14 – Symbologies supported by
KDC
-&%
..
..
&$CTEQFGU
($1
($1
83&$
83&(
%RRNODQG($1
($1ZLWK$GGRQ
($1ZLWK$GGRQ
83&$ZLWK$GGRQ
83&(ZLWK$GGRQ
,QWHUOHDYHRI
,7)
&RGH
&RGDEDU
*6
&RGH
&RGH
&RGH
K
KDC User Manual FAQ
11.2
Host Interface
Q: What interface ports are supported by the KDC?
A: The KDC100 has two USB ports: Swing-out Type A and Ultra-mini USB ports that support USB to
Serial protocol. KDC200/250/300/350/400(except KDC470) have one Ultra-mini USB port that
supports USB to Serial protocol and Bluetooth that supports HID/SPP/MFi Bluetooth profiles.
KDC270 and KDC470 have one Micro USB port. KDC20/30 have one Swing-out Type A USB port
which supports USB to Serial protocol and Bluetooth with HID, SPP and MFi Bluethooth profiles.
KDC500 has one micro USB port that supports USB to Serial protocol and Bluetooth that supports
SPP/MFi Bluetooth profile.
11.3
Battery
Q: How long will the KDC battery last before it needs to be replaced?
A: The battery on the KDC may be charged at least 300 times before it needs to be replaced.
Q: How long does it take to charge the KDC?
A: It takes about 2 hours to charge the KDC20/100/200, 4 hours to charge the KDC30/250/300/270,
and 5 hours to charge the KDC350/400/500.
Q: How many barcodes may a fully charged KDC scan?
A: If the user scans a barcode every 1 seconds, KDC100/30 scans more than 12,000 barcodes, KDC20
scans more than 11,000 barcodes, KDC200 scans more than 8,500 barcodes, KDC250 scans more
than 33,000 scans, KDC300 scans more than 22,000 scans and 2D models of KDC350/400/500 scan
more than 40,000.
Q: How long will the KDC battery lasts in the sleep mode?
A: KDC100 lasts more than 75 days. KDC20/200 lasts more than 2 days while connected in Bluetooth
and 60 days if not connected in Bluetooth. KDC250/270L lasts 7 days while connected in Bluetooth
and 120 days if not connected in Bluetooth. KDC30/270C/300 last more than 25 days while
connected in Bluetooth and 5 days if not connected in Bluetooth. KDC350 lasts more than 12 hours
while GPS is active and Bluetooth is connected, 7 days while GPS is not active and Bluetooth is
connected, and 20 days while GPS is not active and Bluetooth is not connected.
KDC410/415/420/425/430/470 last more than 8 days while connected in Bluetooth and 20 days
while if not connected in Bluetooth. KDC450/470 lasts more than 4 hours while reading RFiD tag
continuously every second and Bluetooth is connected, 5 days if reading RFiD tag casually and
Bluetooth is connected. KDC500 lasts more 7 days while connected in Bluetooth and 10 days if not
connected in Bluetooth.
Q: May I replace the KDC battery?
A: Yes. The KDC has a separate compartment for the battery that may be opened easily with a driver.
KDC batteries may be purchased at www.KOAMTACstore.com or from local KDC reseller.
K
KDC User Manual FAQ
11.4
Memory
Q: How many barcodes may be stored in the KDC?
A: 4MB version of KDC100M/200M/250M/300M350 may storemaximum of 204,800 barcodes and
8MB version and KDC270/470 may store maximum of 409,600 barcodes . KDC20/30 have 150KB
data memory which may store maximum 7,680 barcodes. KDC41x/42x has 80KB data memory and
may store maximum 4,096 barcodes. KDC500 has 3MB data memory which may store maximum
153,600 barcodes.
Q: May I download stored barcodes or wedge barcodes to my application?
A: Yes. KTSync® is keyboard wedging, application generation, DB look up, and inventory program
bundled with the KDC200/250/300/350, which supports host devices running on Android®,
iPhone/iPad/iPod touch, Blackberry®, Windows® XP/Vista/7/8/10/Mobile 5.0+. KTSync® provides
keyboard wedging program only for KDC20/30/400. KDC100 and KDC500 only supports Windows
XP/Vista/7 version.
Q: Does the KDC support Android®, iPhone/iPad/iPod touch®, Blackberry®, Mac® and Windows®
devices?
A: KTSync® currently supports Android®, iPhone/iPad/iPod touch, Blackberry®, Mac® and Windows®
devices.
11.5
Programming
Q: May the KDC be programmed by a KOAMTAC partner?
A: Yes. KOAMTAC’s Application Generation tool provides an enhanced programming environment
for developing custom applications for the KDC.
1. KDC supports, at most, three step data collection processes, including the ability to perform
various data functionality features.
2. KDC’s database lookup function provides enhanced data processes, enabling the KDC to
display database results with or without scanned barcode data.
3. KDC may display a message from the Host by enabling two-way communications and a
messaging application.
Q: Does KOAMTAC provide customization services for the KDC?
A: Yes. Custom applications or projects may be developed by KOAMTAC engineers. This service is
provided for an additional fee to KOAMTAC. For more information regarding this service, please
contact KOAMTAC.
Q: May a partner develop a PC or Smartphone application for the KDC?
A: A software development kit for Windows® XP/Vista/7/8/10/Mobile 5.0+ and Android is available
K
KDC User Manual FAQ
on KOAMTAC support page. Android®, iPhone/iPad/iPod touch, Blackberry®, and Mac® SDK are
available through KOAMTAC authorized distributors.
K
KDC User Manual APPLICATION GENERATION
12. Appendix C – 1D Special Barcodes
(KDC20/20D/100/200/250/350L/350D/410/415)
12.1
Set Symbologies
Enable EAN13
Disable EAN13
Enable EAN8
Disable EAN8
Enable UPCA
Disable UPCA
Enable UPCE
Disable UPCE
Enable Code39
Disable Code39
Enable ITF14
Disable ITF14
K
KDC User Manual APPLICATION GENERATION
Enable Code128
Disable Code128
Enable I2 of 5
Disable I2 of 5
Enable Codabar
Disable Codabar
Enable GS1-128
Disable GS1-128
Enable Code93
Disable Code93
Enable Code35
Disable Code35
Enable Bookland EAN
Disable Bookland EAN
Enable EAN13 with Addon
Disable EAN13 with Addon
K
KDC User Manual APPLICATION GENERATION
Enable EAN8 with Addon
Disable EAN8 with Addon
Enable UPCA with Addon
Disable UPCA with Addon
Enable UPCE with Addon
Disable UPCE with Addon
Enable GS1 Omni
Disable GS1 Omni
Enable GS1 Limited
Disable GS1 Limited
Enable GS1 Expanded
Disable GS1 Expanded
12.2
Barcode Options
Codabar - do NOT transmit start/stop
Codabar - transmit start/stop
K
KDC User Manual APPLICATION GENERATION
Convert UPCE to UPCA
Do NOT convert UPCE to UPCA
Convert EAN8 to EAN13
Do NOT convert EAN8 to EAN13
Convert UPCE to EAN13
Do NOT convert UPCE to EAN13
Return Check Digit
Do NOT Return Check Digit
Verify Check Digit
Do NOT Verify Check Digit
Convert UPCA to EAN13
Do NOT Convert UPCA to EAN13
Verify check digit for I2of5
Do NOT verify check digit for I2of5
Verify check digit for Code39
Do NOT verify check digit for Code39
K
KDC User Manual APPLICATION GENERATION
Return check digit for I2of5
Do NOT return check digit for I2of5
Return check digit for Code39
Do NOT return check digit for Code39
Return check digit for UPCE
Do NOT return check digit for UPCE
Return check digit for UPCA
Do NOT return check digit for UPCA
Return check digit for EAN8
Do NOT return check digit for EAN8
Return check digit for EAN13
Do NOT return check digit for EAN13
12.3
Delete Last Scanned Barcode
Delete Last Scanned Barcode
K
KDC User Manual APPLICATION GENERATION
K
KDC User Manual APPLICATION GENERATION
12.4
Scan Options
Wide Scan Angle*
Narrow Scan Angle*
Normal Filter Mode*
High Filter Mode*
Enable Auto Trigger
Disable Auto Trigger
Reread Delay = Continuous
Reread Delay = Short
Reread Delay = Medium
Reread Delay = Long
Reread Delay = Extra Long
*Opticon laser only
12.5
Scan Timeout
Scan Timeout = 500msec
Scan Timeout = 1sec
K
KDC User Manual APPLICATION GENERATION
Scan Timeout = 2sec
Scan Timeout = 3sec
Scan Timeout = 4sec
Scan Timeout = 5sec
Scan Timeout = 6sec
Scan Timeout = 7sec
Scan Timeout = 8sec
Scan Timeout = 9sec
Scan Timeout = 10sec
12.6
Minimum Barcode Length
Minimum Length = 2
Minimum Length = 3
Minimum Length = 4
Minimum Length = 5
K
KDC User Manual APPLICATION GENERATION
Minimum Length = 6
Minimum Length = 7
Minimum Length = 8
Minimum Length = 9
Minimum Length = 10
Minimum Length = 11
Minimum Length = 12
Minimum Length = 13
Minimum Length = 14
Minimum Length = 15
Minimum Length = 16
Minimum Length = 17
Minimum Length = 18
Minimum Length = 19
Minimum Length = 20
Minimum Length = 21
K
KDC User Manual APPLICATION GENERATION
Minimum Length = 22
Minimum Length = 23
Minimum Length = 24
Minimum Length = 25
Minimum Length = 26
Minimum Length = 27
Minimum Length = 28
Minimum Length = 29
Minimum Length = 30
Minimum Length = 31
Minimum Length = 32
Minimum Length = 33
Minimum Length = 34
Minimum Length = 35
Minimum Length = 36
K
KDC User Manual APPLICATION GENERATION
12.7
ScanIfConnect
ScanIfConnect = Enable
ScanIfConnect = Disable
K
KDC User Manual APPLICATION GENERATION
12.8
Security Level(Laser model only)
Security level = 1
Security level = 2
Security level = 3
Security level = 4
K
KDC User Manual APPLICATION GENERATION
12.9
Data Process - Wedge/Store, Enter Key &
Extend Key
Wedge Only
Wedge & Store Always
Store Only
Save if Sent
Save if Not Sent
Enable Enter Key (KDC350L/D Only)
Disable Enter Key (KDC350L/D Only)
Enable Extend Key (KDC350L/D Only)
Disable Extend Key (KDC350L/D Only)
K
KDC User Manual APPLICATION GENERATION
12.10
Data Process - Data Edit
Start Prefix Enter
Start Suffix Enter
Finish Prefix/Suffix Enter
Cancel Prefix/Suffix Enter
Delete Prefix
Delete Suffix
Display Prefix
Display Suffix
AIM ID None
AIM ID In Prefix
AIM ID In Suffix
K
KDC User Manual 1D SPECIAL BARCODES
12.10 Data Process - Data Format & Handshake
Data format = Barcode only
Data format = Packet data
Enable Handshake
Disable Handshake
K
KDC User Manual 1D SPECIAL BARCODES
12.11 Data Process - Termination Character &
Duplicate Check
Termination Character = None
Termination Character = CR
Termination Character = LF
Termination Character = CR+LF
Termination Character = Tab
Enable Duplicate Check
Disable Duplicate Check
K
KDC User Manual 1D SPECIAL BARCODES
12.11
Bluetooth
Enable Bluetooth Power
Disable Bluetooth Power
Enter Pairing Mode
Enable Discovering
Disable Discovering
Connect To Last
Connecting to
Disconnect
HID Sync
SPP Sync
Bluetooth Profile = SPP
Bluetooth Profile = HID iOS
K
KDC User Manual 1D SPECIAL BARCODES
Bluetooth Profile = MFi
Bluetooth Profile = SPP2.0
Bluetooth Profile = HID Normal
Enable Auto Connect
Disable Auto Connect
Enable Auto Reconnect
Disable Auto Reconnect
Enable Auto Power On
Disable Auto Power On
Enable Auto Power Off
Disable Auto Power Off
Enable Beep Warning
Disable Beep Warning
Enable Power Off Msg
Disable Power Off Msg
K
KDC User Manual 1D SPECIAL BARCODES
Display BT MAC Address
Display BT FW Version
Enable Wakeup Nulls
Disable Wakeup Nulls
Enable BT Toggle
Disable BT Toggle
Enable BT Disconnect Button
Disable BT Disconnect Button
Enable Auto Pairing
Disable Auto Pairing
K
KDC User Manual 1D SPECIAL BARCODES
12.12
Bluetooth Auto Power On Time
Auto Power On Time = Disabled
Auto Power On Time = 1sec
Auto Power On Time = 2sec
Auto Power On Time = 3sec
Auto Power On Time = 4sec
Auto Power On Time = 5sec
Auto Power On Time = 6sec
Auto Power On Time = 7sec
Auto Power On Time = 8sec
Auto Power On Time = 9sec
Auto Power On Time = 10sec
K
KDC User Manual 1D SPECIAL BARCODES
12.13
Bluetooth Power Off Time
BT Power Off Time = 1min
BT Power Off Time = 2min
BT Power Off Time = 3min
BT Power Off Time = 4min
BT Power Off Time = 5min
BT Power Off Time = 6min
BT Power Off Time = 7min
BT Power Off Time = 8min
BT Power Off Time = 9min
BT Power Off Time = 10min
BT Power Off Time = 11min
BT Power Off Time = 12min
BT Power Off Time = 13min
BT Power Off Time = 14min
K
KDC User Manual 1D SPECIAL BARCODES
BT Power Off Time = 15min
BT Power Off Time = 16min
BT Power Off Time = 17min
BT Power Off Time = 18min
BT Power Off Time = 19min
BT Power Off Time = 20min
BT Power Off Time = 21min
BT Power Off Time = 22min
BT Power Off Time = 23min
BT Power Off Time = 24min
BT Power Off Time = 25min
BT Power Off Time = 26min
BT Power Off Time = 27min
BT Power Off Time = 28min
BT Power Off Time = 29min
BT Power Off Time = 30min
K
KDC User Manual 1D SPECIAL BARCODES
12.14
HID Auto Lock Time
HID Auto Lock Time = 0min (Never)
HID Auto Lock Time = 1min
HID Auto Lock Time = 2min
HID Auto Lock Time = 3min
HID Auto Lock Time = 4min
HID Auto Lock Time = 5min
HID Auto Lock Time = 10min
HID Auto Lock Time = 15min
K
KDC User Manual 1D SPECIAL BARCODES
12.15
HID Keyboard
HID Keyboard = US
HID Keyboard = German
HID Keyboard = French
HID Keyboard = Italian
HID Keyboard = Spanish
K
KDC User Manual 1D SPECIAL BARCODES
12.16
HID Initial Delay
HID Initial Delay = Disabled
HID Initial Delay = 1second
HID Initial Delay = 2seconds
HID Initial Delay = 3seconds
HID Initial Delay = 5seconds
HID Initial Delay = 10seconds
K
KDC User Manual 1D SPECIAL BARCODES
12.17
HID Character Delay
HID Character Delay = Disabled
HID Character Delay = 10msec
HID Character Delay = 20msec
HID Character Delay = 30msec
HID Character Delay = 50msec
HID Character Delay = 100msec
K
KDC User Manual 1D SPECIAL BARCODES
12.18
HID Control Character
HID Control Character = Disabled
HID Control Character = Alt+Numpad
HID Control Character = ^+Character
HID Control Character = Replace with ‘|’
K
KDC User Manual 1D SPECIAL BARCODES
12.19
System
Memory Size = 0.5M / 3.5M Note1,2
Memory Size = 1M / 3M Note1,2
Memory Size = 2M / 2M Note1,2
Memory Size = 3M / 1M Note1,2
Memory Size = 4M / 0M Note1,2
Confirm Memory Size Change Note1,2
Memory Size = 5M / 3M Note2
Memory Size = 6M / 2M Note2
Memory Size = 7M / 1M Note2
Memory Size = 8M / 0M Note2
Memory Status
Reset Memory
Erase Memory
Reset App data
ଖ Note 1. 4M Model Only
ଖG Note 2. 8M Model Only
K
KDC User Manual 1D SPECIAL BARCODES
Reset BT Registry
Enable Auto Erase
Disable Auto Erase
Date/Time
Battery
Display Version
Lock Button
Unlock Button
Enable Beep Sound
Disable Beep Sound
High Beep Volume
Low Beep Volume
Enable Auto Menu Exit
Disable Auto Menu Exit
K
KDC User Manual 1D SPECIAL BARCODES
Enable MFi Mode
Disable MFi Mode
Enable Vibrator
Disable Vibrator
Scan Success = No vibration
Scan Success = 1 vibration
Scan Success = 2 vibrations
Scan Success = 3 vibrations
Scan Success = 4 vibrations
Scan Success = 5 vibrations
Scan Failure = No vibration
Scan Failure = 1 vibration
Scan Failure = 2 vibrations
Scan Failure = 3 vibrations
Scan Failure = 4 vibrations
Scan Failure = 5 vibrations
K
KDC User Manual 1D SPECIAL BARCODES
Enable Port Status
Disable Port Status
Display Format = Time & Battery
Display Format = Type & Time
Display Format = Type & Battery
Display Format = Memory Status
Display Format = GPS Data (GPS Model)
Display Format = Barcode Only
Display Format = Graphic
Enable Scrolling
Disable Scrolling
Factory Default
KDC Reset
Enable Backup Battery (KDC20/20D Only)
Disable Backup Battery (KDC20/20D Only)
K
KDC User Manual 1D SPECIAL BARCODES
12.20
Sleep Timeout
Sleep Timeout = Disable
Sleep Timeout = 1sec
Sleep Timeout = 2sec
Sleep Timeout = 3sec
Sleep Timeout = 4sec
Sleep Timeout = 5sec
Sleep Timeout = 10sec
Sleep Timeout = 20sec
Sleep Timeout = 30sec
Sleep Timeout = 1min
Sleep Timeout = 2min
Sleep Timeout = 5min
Sleep Timeout = 10min
K
KDC User Manual 1D SPECIAL BARCODES
12.21
ETC
Enable Reverse Direction
Disable Reverse Direction
Enable Verify check digit
Disable Verify check digit
Enable Return check digit
Disable Return check digit
K
KDC User Manual 1D SPECIAL BARCODES
12.22
Function
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
12.23
Number
0
1
K
KDC User Manual 1D SPECIAL BARCODES
2
3
4
5
6
7
8
9
K
KDC User Manual 1D SPECIAL BARCODES
12.24
Lower Case Alphabet
a
b
c
d
e
f
g
h
i
j
k
l
m
n
K
KDC User Manual 1D SPECIAL BARCODES
o
p
q
r
s
t
u
v
w
x
y
z
K
KDC User Manual 1D SPECIAL BARCODES
12.25
Upper Case Alphabet
A
B
C
D
E
F
G
H
I
J
K
L
M
N
K
KDC User Manual 1D SPECIAL BARCODES
O
P
Q
R
S
T
U
V
W
X
Y
Z
K
KDC User Manual 1D SPECIAL BARCODES
12.26
Control Character
BS
TAB
LF
VT
CR
ESC
Space
DEL
Shift + Tab
K
KDC User Manual 1D SPECIAL BARCODES
12.27
Symbol Character
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
K
KDC User Manual 1D SPECIAL BARCODES
/
:
;
<
=
>
?
@
[
\
]
^
_
`
{
|
K
KDC User Manual 1D SPECIAL BARCODES
}
~
Start String
Stop String
x The user may compose a string up to 16 characters.
x A string would be composed by scanning the “Start-String”, number/alphabet/special
characters, and “Stop-String” special barcodes.
x The KDC will abort string composition if the user do not scan
“Stop-String” in one minute after scanning “Start-String” and number/alphabet/special
characters.
K
KDC User Manual 1D SPECIAL BARCODES
12.28
GPS (GPS Model Only)
Enable GPS Power
Disable GPS Power
Enable GPS Bypass Data
Disable GPS Bypass Data
Reset GPS Module
GPS Acquire Test
GPS Power Save Mode = Normal
GPS Power Save Mode = Power Saving
Enable GPS Auto Power Off
Disable GPS Auto Power Off
K
KDC User Manual 1D SPECIAL BARCODES
12.29
GPS/BT Auto Power Off Timeout
Auto Power Off = 0min (Disabled)
Auto Power Off = 5min
Auto Power Off = 10min
Auto Power Off = 20min
Auto Power Off = 30min
Auto Power Off = 60min
Auto Power Off = 120min
K
KDC User Manual 1D SPECIAL BARCODES
12.30
NFC (NFC Model Only)
Enable NFC Power
Disable NFC Power
NFC Data Format = Data only
NFC Data Format = Packet data
UID Only = Enable
UID Only = Disable
New Data Format = Enable
New Data Format = Disable
K
KDC User Manual 1D SPECIAL BARCODES
12.31
USB Disk (M Model Only)
USB Serial Mode
USB Disk Mode
USB HID Mode
Format USB Disk
Data Format = Data
Data Format = Data, Time
Data Format = Data, Type
Data Format = Data, Time, Type
12.32
USB DM Button(KDC20/20D Only)
USB DM Button = Enable
USB DM Button = Disable
K
KDC User Manual 1D SPECIAL BARCODES
12.33
WIFI (WIFI Model Only)
Enable WIFI Power
Disable WIFI Power
Provisioning
Protocol = UDP
Protocol = TCP
Protocol = HTTP_GET
Protocol = HTTP_POST
Server URL
Port Number
Server Page
Enable SSL
Disable SSL
Enable AutoConnect
Disable AutoConnect
K
KDC User Manual 1D SPECIAL BARCODES
AP SSID
AP Passcode
Connect
Server IP
Enable Send Stored
Disable Send Stored
12.34
Multilanguage
Disable(English Only)
English
French
Italian
Spanish
Korean
Japanese
K
KDC User Manual 2D SPECIAL BARCODES
13. Appendix D – 2D Special Barcodes
(KDC30/300/350C/350WA/420/425/450)
13.1
Set Symbologies
For KDC300/350C/420/425/450, please refer to Honeywell Adaptus® Technology enabled scanner
user manual, such as 4600 or 4820.
13.2
Barcode Options
For KDC300/350C/420/425/450, please refer to Honeywell Adaptus® Technology enabled scanner
user manual, such as 4600 or 4820.
13.3
Delete Last Scanned Barcode
Delete Last Scanned Barcode
K
KDC User Manual 2D SPECIAL BARCODES
13.4
Scan Options
Enable Auto Trigger
Disable Auto Trigger
Reread Delay = Continuous
Reread Delay = Short
Reread Delay = Medium
Reread Delay = Long
Reread Delay = Extra Long
K
KDC User Manual 2D SPECIAL BARCODES
13.5
Scan Timeout
Scan Timeout = 500msec
Scan Timeout = 1sec
Scan Timeout = 2sec
Scan Timeout = 3sec
Scan Timeout = 4sec
Scan Timeout = 5sec
Scan Timeout = 6sec
Scan Timeout = 7sec
Scan Timeout = 8sec
Scan Timeout = 9sec
Scan Timeout = 10sec
K
KDC User Manual 2D SPECIAL BARCODES
13.6
Minimum Barcode Length (except KDC30)
Minimum Length = 2
Minimum Length = 3
Minimum Length = 4
Minimum Length = 5
Minimum Length = 6
Minimum Length = 7
Minimum Length = 8
Minimum Length = 9
Minimum Length = 10
Minimum Length = 11
Minimum Length = 12
Minimum Length = 13
Minimum Length = 14
Minimum Length = 15
K
KDC User Manual 2D SPECIAL BARCODES
Minimum Length = 16
Minimum Length = 17
Minimum Length = 18
Minimum Length = 19
Minimum Length = 20
Minimum Length = 21
Minimum Length = 22
Minimum Length = 23
Minimum Length = 24
Minimum Length = 25
Minimum Length = 26
Minimum Length = 27
Minimum Length = 28
Minimum Length = 29
Minimum Length = 30
Minimum Length = 31
K
KDC User Manual 2D SPECIAL BARCODES
Minimum Length = 32
Minimum Length = 33
Minimum Length = 34
Minimum Length = 35
Minimum Length = 36
K
KDC User Manual 2D SPECIAL BARCODES
13.7
Image Capture (except KDC30)
Capture Now
Enable Image Capture
Image Format = JPEG
Image Format = BMP
Pixel Depth = 1 bit per pixel
Pixel Depth = 8 bit per pixel
13.8
ScanIfConnect
ScanIfConnect = Enable
ScanIfConnect = Disable
K
KDC User Manual 2D SPECIAL BARCODES
13.9
Data Process - Wedge/Store, Enter Key &
Extend Key
Wedge Only
Wedge & Store Always
Store Only
Save if Sent
Save if Not Sent
Enable Enter Key (KDC350C Only)
Disable Enter Key (KDC350C Only)
Enable Extend Key (KDC350C Only)
Disable Extend Key (KDC350C Only)
Enable Age Verification
Disable Age Verification
K
KDC User Manual 2D SPECIAL BARCODES
13.10
Data Process - Data Edit
Start Prefix Enter
Start Suffix Enter
Finish Prefix / Suffix Enter
Cancel Prefix / Suffix Enter
Delete Prefix
Delete Suffix
Display Prefix
Display Suffix
AIM ID None
AIM ID In Prefix
AIM ID In Suffix
K
KDC User Manual 2D SPECIAL BARCODES
13.11
Data Process – Data Format & Handshake
Data format = Barcode only
Data format = Packet data
Enable Handshake
Disable Handshake
K
KDC User Manual 2D SPECIAL BARCODES
13.12
Data Process - Termination Character &
Duplicate Check
Termination Character = None
Termination Character = CR
Termination Character = LF
Termination Character = CR+LF
Termination Character = Tab
Enable Duplicate Check
Disable Duplicate Check
K
KDC User Manual 2D SPECIAL BARCODES
13.13
Bluetooth
Enable Bluetooth Power
Disable Bluetooth Power
Enter Pairing Mode
Enable Discovering
Disable Discovering
Connect To Last
Connect To
Disconnect
HID Sync
SPP Sync
Bluetooth Profile = SPP
Bluetooth Profile = HID iOS
K
KDC User Manual 2D SPECIAL BARCODES
Bluetooth Profile = MFi
Bluetooth Profile = SPP2.0
Bluetooth Profile = HID Normal
Enable Auto Connect
Disable Auto Connect
Enable Auto Reconnect
Disable Auto Reconnect
Enable Auto Power Off
Disable Auto Power Off
Enable Auto Power On
Disable Auto Power On
Enable Beep Warning
Disable Beep Warning
Enable Power Off Msg
Disable Power Off Msg
K
KDC User Manual 2D SPECIAL BARCODES
Display BT Mac Address
Display BT FW Version
Enable Wakeup Nulls
Disable Wakeup Nulls
Enable BT Toggle
Disable BT Toggle
Enable BT Disconnect Button
Disable BT Disconnect Button
Enable Auto Pairing
Disable Auto Pairing
K
KDC User Manual 2D SPECIAL BARCODES
13.14
Bluetooth Auto Power On Time
Auto Power On Time = Disabled
Auto Power On Time = 1sec
Auto Power On Time = 2sec
Auto Power On Time = 3sec
Auto Power On Time = 4sec
Auto Power On Time = 5sec
Auto Power On Time = 6sec
Auto Power On Time = 7sec
Auto Power On Time = 8sec
Auto Power On Time = 9sec
Auto Power On Time = 10sec
K
KDC User Manual 2D SPECIAL BARCODES
13.15
Bluetooth Power Off Time
BT Power Off Time = 1min
BT Power Off Time = 2min
BT Power Off Time = 3min
BT Power Off Time = 4min
BT Power Off Time = 5min
BT Power Off Time = 6min
BT Power Off Time = 7min
BT Power Off Time = 8min
BT Power Off Time = 9min
BT Power Off Time = 10min
BT Power Off Time = 11min
BT Power Off Time = 12min
BT Power Off Time = 13min
BT Power Off Time = 14min
K
KDC User Manual 2D SPECIAL BARCODES
BT Power Off Time = 15min
BT Power Off Time = 16min
BT Power Off Time = 17min
BT Power Off Time = 18min
BT Power Off Time = 19min
BT Power Off Time = 20min
BT Power Off Time = 21min
BT Power Off Time = 22min
BT Power Off Time = 23min
BT Power Off Time = 24min
BT Power Off Time = 25min
BT Power Off Time = 26min
BT Power Off Time = 27min
BT Power Off Time = 28min
BT Power Off Time = 29min
BT Power Off Time = 30min
K
KDC User Manual 2D SPECIAL BARCODES
13.16
HID Auto Lock Time
HID Auto Lock Time = 0min (Never)
HID Auto Lock Time = 1min
HID Auto Lock Time = 2min
HID Auto Lock Time = 3min
HID Auto Lock Time = 4min
HID Auto Lock Time = 5min
HID Auto Lock Time = 10min
HID Auto Lock Time = 15min
K
KDC User Manual 2D SPECIAL BARCODES
13.17
HID Keyboard
HID Keyboard = US
HID Keyboard = German
HID Keyboard = French
HID Keyboard = Italian
HID Keyboard = Spanish
K
KDC User Manual 2D SPECIAL BARCODES
13.18
HID Initial Delay
HID Initial Delay = Disabled
HID Initial Delay = 1second
HID Initial Delay = 2seconds
HID Initial Delay = 3seconds
HID Initial Delay = 5seconds
HID Initial Delay = 10seconds
K
KDC User Manual 2D SPECIAL BARCODES
13.19
HID Character Delay
HID Character Delay = Disabled
HID Character Delay = 10msec
HID Character Delay = 20msec
HID Character Delay = 30msec
HID Character Delay = 50msec
HID Character Delay = 100msec
K
KDC User Manual 2D SPECIAL BARCODES
13.20
HID Control Character
HID Control Character = Disabled
HID Control Character = Alt+Numpad
HID Control Character = ^+Character
HID Control Character = Replace with ‘|’
K
KDC User Manual 2D SPECIAL BARCODES
13.21
System
Memory Size = 0.5M / 3.5M Note1,2
Memory Size = 1M / 3M Note1,2
Memory Size = 2M / 2M Note1,2
Memory Size = 3M / 1M Note1,2
Memory Size = 4M / 0M Note1,2
Confirm memory size Note1,2
Memory Size = 5M / 3M Note2
Memory Size = 6M / 2M Note2
Memory Size = 7M / 1M Note2
Memory Size = 8M / 0M Note2
Memory Status
Reset Memory
Erase Memory
Reset App data
ଖ Note 1. 4M Model Only
ଖG Note 2. 8M Model Only
K
KDC User Manual 2D SPECIAL BARCODES
Reset BT Registry
Enable Auto Erase
Disable Auto Erase
Date/Time
Battery
Display Version
Lock Button
Unlock Button
Enable Beep Sound
Disable Beep Sound
High Beep Volume
Low Beep Volume
Enable MFi Mode
Disable MFi Mode
K
KDC User Manual 2D SPECIAL BARCODES
Enable Vibrator
Disable Vibrator
Scan Success = No vibration
Scan Success = 1 vibration
Scan Success = 2 vibrations
Scan Success = 3 vibrations
Scan Success = 4 vibrations
Scan Success = 5 vibrations
Scan Failure = No vibration
Scan Failure = 1 vibration
Scan Failure = 2 vibrations
Scan Failure = 3 vibrations
Scan Failure = 4 vibrations
Scan Failure = 5 vibrations
Enable Auto Menu Exit
Disable Auto Menu Exit
K
KDC User Manual 2D SPECIAL BARCODES
Enable Port Status
Disable Port Status
Display Format = Time & Battery
Display Format = Type & Time
Display Format = Type & Battery
Display Format = Memory Status
Display Format = GPS Data(GPS Model)
Display Format = Barcode Only
Display Format = Graphic
Enable Menu Barcode
Disable Menu Barcode
Enable Scrolling
Disable Scrolling
Factory Default
KDC Reset
K
KDC User Manual 2D SPECIAL BARCODES
13.22
Sleep Timeout
Sleep Timeout = Disable
Sleep Timeout = 1sec
Sleep Timeout = 2sec
Sleep Timeout = 3sec
Sleep Timeout = 4sec
Sleep Timeout = 5sec
Sleep Timeout = 10sec
Sleep Timeout = 20sec
Sleep Timeout = 30sec
Sleep Timeout = 1min
Sleep Timeout = 2min
Sleep Timeout = 5min
Sleep Timeout = 10min
K
KDC User Manual 2D SPECIAL BARCODES
13.23
Function
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
K
KDC User Manual 2D SPECIAL BARCODES
13.24
Number
0
1
2
3
4
5
6
7
8
9
K
KDC User Manual 2D SPECIAL BARCODES
13.25
Lower Case Alphabet
a
b
c
d
e
f
g
h
j
i
k
l
m
n
K
KDC User Manual 2D SPECIAL BARCODES
o
p
q
r
s
t
u
v
w
x
y
z
K
KDC User Manual 2D SPECIAL BARCODES
13.26
Upper Case Alphabet
A
B
C
D
E
F
G
H
I
J
K
L
M
N
K
KDC User Manual 2D SPECIAL BARCODES
O
P
Q
R
S
T
U
V
W
X
Y
Z
K
KDC User Manual 2D SPECIAL BARCODES
13.27
Control Character
BS
TAB
LF
VT
CR
ESC
Space
DEL
Shift + Tab
K
KDC User Manual 2D SPECIAL BARCODES
13.28
Symbol Character
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
K
KDC User Manual 2D SPECIAL BARCODES
/
:
;
<
=
>
?
@
[
\
]
^
_
`
{
|
K
KDC User Manual 2D SPECIAL BARCODES
0QVG
}
~
Start String
Stop String
x The user may compose a string up to 16 characters.
x A string would be composed by scanning the “Start-String”, number/alphabet/special
characters, and “Stop-String” special barcodes.
x The KDC will abort string composition if the user do not scan
“Stop-String” in one minute after scanning “Start-String” and number/alphabet/special
characters.
K
KDC User Manual 2D SPECIAL BARCODES
13.29
GPS (GPS Model Only)
Enable GPS Power
Disable GPS Power
Enable GPS Bypass Data
Disable GPS Bypass Data
Reset GPS Module
GPS Acquire Test
GPS Power Save Mode = Normal
GPS Power Save Mode = Power Saving
Enable GPS Auto Power Off
Disable GPS Auto Power Off
K
KDC User Manual 2D SPECIAL BARCODES
13.30
GPS/BT Auto Power Off Timeout
Auto Power Off = 0min (Disabled)
Auto Power Off = 5min
Auto Power Off = 10min
Auto Power Off = 20min
Auto Power Off = 30min
Auto Power Off = 60min
Auto Power Off = 120min
K
KDC User Manual 2D SPECIAL BARCODES
13.31
NFC (NFC Model Only)
Enable NFC Power
Disable NFC Power
NFC Data Format = Data only
NFC Data Format = Packet data
UID Only = Enable
UID Only = Disable
New Data Format = Enable
New Data Format = Disable
13.32
UHF (UHF Model Only)
Enable UHF Power
Disable NFC Power
Power On Time = 500ms
Power On Time = 1 sec
K
KDC User Manual 2D SPECIAL BARCODES
Power On Time = 1.5 sec
Power On Time = 2 sec
Power On Time = 2.5 sec
Power On Time = 3 sec
Power On Time = 3.5 sec
Power On Time = 4 sec
Power On Time = 4.5 sec
Power On Time = 5 sec
Power Off Time = 500ms
Power Off Time = 1 sec
Power Off Time = 1.5 sec
Power Off Time = 2 sec
Power Off Time = 2.5 sec
Power Off Time = 3 sec
Power Off Time = 3.5 sec
Power Off Time = 4 sec
K
KDC User Manual 2D SPECIAL BARCODES
Power Off Time = 4.5 sec
Power Off Time = 5 sec
Power Level = 0
Power Level = 1
Power Level = 2
Power Level = 3
Power Level = 4
Power Level = 5
Power Level = 6
Power Level = 7
Data Format = Binary
Data Format = Hexa Decimal
Smart Hopping
K
KDC User Manual 2D SPECIAL BARCODES
13.33
USB Disk (M Model Only)
USB Serial Mode
USB Disk Mode
USB HID Mode
Format USB Disk
Data Format = Data
Data Format = Data,Time
Data Format = Data,Type
Data Format = Data,Time,Type
13.34
USB DM Button(KDC30 only)
USB DM Button = Enable
USB DM Button = Disable
K
KDC User Manual 2D SPECIAL BARCODES
13.35
WIFI (WIFI Model Only)
Enable WIFI Power
Disable WIFI Power
Provisioning
Protocol = UDP
Protocol = TCP
Protocol = HTTP_GET
Protocol = HTTP_POST
Server URL
Port Number
Server Page
Enable SSL
Disable SSL
Enable AutoConnect
Disable AutoConnect
K
KDC User Manual 2D SPECIAL BARCODES
AP SSID
AP Passcode
Connect
Server IP
Enable Send Stored
Disable Send Stored
K
KDC User Manual 2D SPECIAL BARCODES
13.36
CDMA (KDC350WA CDMA Model Only)
Enable CDMA Power
Disable CDMA Power
K
KDC User Manual MULTIPLE SPECIAL BARCODES
13.37
Multilanguage
Disable(English Only)
English
French
Italian
Spanish
Korean
Japanese
K
KDC User Manual MULTIPLE SPECIAL BARCODES
14. APPENDIX E - MSR Special Barcodes
(KDC415/425MSR)
14.1
KDC415MSR
Beep On Error
No Beep On Error
Beep On Error
Data Format
MSR Data Only
Packet data
Encrypt Mode
Disabled
AES
Enable Track
Enable Track1
Enable Track2
Enable Track3
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Disable Track
Disable Track1
Disable Track2
Disable Track3
Track Separator
Track Separator = None
Track Separator = Space
Track Separator = Comma
Track Separator = Semi Colon
Track Separator = CR
Track Separator = LF
Track Separator = CR+LF
Track Separator = Tab
AES Key Length
AES Key Length = 128 bits
AES Key Length = 192 bits
K
KDC User Manual MULTIPLE SPECIAL BARCODES
AES Key Length = 256 bits
MSR Card Type
MSR Card Type = ISO
MSR Card Type = Other 1
MSR Card Type = AAMVA
K
KDC User Manual MULTIPLE SPECIAL BARCODES
14.2
KDC425MSR
Beep On Error
No Beep On Error
Beep On Error
Data Format
MSR Data Only
Packet data
Encrypt Mode
Disabled
AES
Enable Track
Enable Track1
Enable Track2
Enable Track3
Disable Track
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Disable Track1
Disable Track2
Disable Track3
Track Separator
Track Separator = None
Track Separator = Space
Track Separator = Comma
Track Separator = Semi Colon
Track Separator = CR
Track Separator = LF
Track Separator = CR+LF
Track Separator = Tab
AES Key Length
K
KDC User Manual MULTIPLE SPECIAL BARCODES
AES Key Length = 128 bits
AES Key Length = 192 bits
AES Key Length = 256 bits
MSR Card Type
MSR Card Type = ISO
MSR Card Type = Other 1
MSR Card Type = AAMVA
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15. Appendix F – 1D Special Barcodes
(500D)
15.1
Set Symbologies
Enable EAN13
Disable EAN13
Enable EAN8
Disable EAN8
Enable UPCA
Disable UPCA
Enable UPCE
Disable UPCE
Enable Code39
Disable Code39
Enable ITF14
Disable ITF14
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Enable Code128
Disable Code128
Enable I2 of 5
Disable I2 of 5
Enable Codabar
Disable Codabar
Enable GS1-128
Disable GS1-128
Enable Code93
Disable Code93
Enable Code35
Disable Code35
Enable Bookland EAN
Disable Bookland EAN
Enable EAN13 with Addon
Disable EAN13 with Addon
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Enable EAN8 with Addon
Disable EAN8 with Addon
Enable UPCA with Addon
Disable UPCA with Addon
Enable UPCE with Addon
Disable UPCE with Addon
Enable GS1 Omni
Disable GS1 Omni
Enable GS1 Limited
Disable GS1 Limited
Enable GS1 Expanded
Disable GS1 Expanded
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.2
Barcode Options
Codabar - do NOT transmit start/stop
Codabar - transmit start/stop
Convert UPCE to UPCA
Do NOT convert UPCE to UPCA
Convert EAN8 to EAN13
Do NOT convert EAN8 to EAN13
Convert UPCE to EAN13
Do NOT convert UPCE to EAN13
Return Check Digit
Do NOT Return Check Digit
Verify Check Digit
Do NOT Verify Check Digit
Convert UPCA to EAN13
Do NOT Convert UPCA to EAN13
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Verify check digit for I2of5
Do NOT verify check digit for I2of5
Verify check digit for Code39
Do NOT verify check digit for Code39
Return check digit for I2of5
Do NOT return check digit for I2of5
Return check digit for Code39
Do NOT return check digit for Code39
Return check digit for UPCE
Do NOT return check digit for UPCE
Return check digit for UPCA
Do NOT return check digit for UPCA
Return check digit for EAN8
Do NOT return check digit for EAN8
Return check digit for EAN13
Do NOT return check digit for EAN13
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.3
Delete Last Scanned Barcode
Delete Last Scanned Barcode
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.4
Scan Options
Enable Auto Trigger
Disable Auto Trigger
Reread Delay = Continuous
Reread Delay = Short
Reread Delay = Medium
Reread Delay = Long
Reread Delay = Extra Long
15.5
Scan Timeout
Scan Timeout = 500msec
Scan Timeout = 1sec
Scan Timeout = 2sec
Scan Timeout = 3sec
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Scan Timeout = 4sec
Scan Timeout = 5sec
Scan Timeout = 6sec
Scan Timeout = 7sec
Scan Timeout = 8sec
Scan Timeout = 9sec
Scan Timeout = 10sec
15.6
Minimum Barcode Length
Minimum Length = 2
Minimum Length = 3
Minimum Length = 4
Minimum Length = 5
Minimum Length = 6
Minimum Length = 7
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Minimum Length = 8
Minimum Length = 9
Minimum Length = 10
Minimum Length = 11
Minimum Length = 12
Minimum Length = 13
Minimum Length = 14
Minimum Length = 15
Minimum Length = 16
Minimum Length = 17
Minimum Length = 18
Minimum Length = 19
Minimum Length = 20
Minimum Length = 21
Minimum Length = 22
Minimum Length = 23
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Minimum Length = 24
Minimum Length = 25
Minimum Length = 26
Minimum Length = 27
Minimum Length = 28
Minimum Length = 29
Minimum Length = 30
Minimum Length = 31
Minimum Length = 32
Minimum Length = 33
Minimum Length = 34
Minimum Length = 35
Minimum Length = 36
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.7
ScanIfConnect
ScanIfConnect = Enable
ScanIfConnect = Disable
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.8
Data Process - Wedge/Store, Enter Key & Extend
Key
Wedge Only
Wedge & Store Always
Store Only
Save if Sent
Save if Not Sent
Enable Enter Key
Disable Enter Key
Enable Extend Key
Disable Extend Key
15.9
Data Process - Data Edit
Start Prefix Enter
Start Suffix Enter
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Finish Prefix/Suffix Enter
Cancel Prefix/Suffix Enter
Delete Prefix
Delete Suffix
Display Prefix
Display Suffix
AIM ID None
AIM ID In Prefix
AIM ID In Suffix
15.10
Data Process - Data Format
Data format = Barcode only
Data format = Packet data
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.11
Data Process - Termination Character &
Duplicate Check
Termination Character = None
Termination Character = CR
Termination Character = LF
Termination Character = CR+LF
Termination Character = Tab
Enable Duplicate Check
Disable Duplicate Check
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.12
Bluetooth
Enable Bluetooth Power
Disable Bluetooth Power
Enter Pairing Mode
Disconnect
Enable Auto Pairing
Disable Auto Pairing
Bluetooth Profile = SPP
Bluetooth Profile = MFi
Enable Auto Reconnect
Disable Auto Reconnect
Display BT MAC Address
Display BT FW Version
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.13
System
Memory Status
Reset Memory
Enable Auto Erase
Disable Auto Erase
Battery
Display Version
Serial Number
Enable Beep Sound
Disable Beep Sound
Enable Power On Beep
Disable Power On Beep
Enable BeepOnConnect
Disable BeepOnConnect
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Enable Beep On Scan
Disable Beep On Scan
Enable BeepOnMSCard
Disable BeepOnMSCard
Enable BeepOnICCard
Disable BeepOnICCard
Enable BeepOnNFCCard
Disable BeepOnNFCCard
High Beep Volume
Low Beep Volume
Enable Auto Menu Exit
Disable Auto Menu Exit
Enable Port Status
Disable Port Status
Display Format = Time & Battery
Display Format = Type & Time
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Display Format = Type & Battery
Display Format = Memory Status
Display Format = Barcode Only
Factory Default
KDC Reset
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.14
Sleep Timeout
Sleep Timeout = Disable
Sleep Timeout = 5sec
Sleep Timeout = 10sec
Sleep Timeout = 20sec
Sleep Timeout = 30sec
Sleep Timeout = 1min
Sleep Timeout = 2min
Sleep Timeout = 5min
Sleep Timeout = 10min
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.15
NFC
Enable NFC Power
Disable NFC Power
15.16
MSR
Enable MSR Power
Disable MSR Power
No Beep On Error
Beep On Error
Enable Use Track1
Disable Use Track1
Enable Use Track2
Disable Use Track2
Enable Use Track3
Disable Use Track3
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Enable Null Check Track1
Disable Null Check Track1
Enable Null Check Track2
Disable Null Check Track2
Enable Null Check Track3
Disable Null Check Track3
Enable Attach SS/ES
Disable Attach SS/ES
MSR Card Type = ISO
MSR Card Type = Other 1
MSR Card Type = AAMVA
MSR Card Type = JIS 2
K
KDC User Manual MULTIPLE SPECIAL BARCODES
15.17
ICCR(IC CARD READER)
Enable ICCR Power
Disable ICCR Power
IFD Number
Config Number
15.18
Key Management
Stored Keys
Inject Keys
15.19
Multilanguage
English
Korean
Japanese
K
KDC User Manual MULTIPLE SPECIAL BARCODES
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16. Appendix G – 2D Special Barcodes
(KDC500C)
16.1
Set Symbologies
For KDC500C, please refer to Honeywell Adaptus® Technology enabled scanner user manual, such as
5600.
16.2
Barcode Options
For KDC500C, please refer to Honeywell Adaptus® Technology enabled scanner user manual, such as
5600.
16.3
Delete Last Scanned Barcode
Delete Last Scanned Barcode
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.4
Scan Options
Enable Auto Trigger
Disable Auto Trigger
Reread Delay = Continuous
Reread Delay = Short
Reread Delay = Medium
Reread Delay = Long
Reread Delay = Extra Long
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.5
Scan Timeout
Scan Timeout = 500msec
Scan Timeout = 1sec
Scan Timeout = 2sec
Scan Timeout = 3sec
Scan Timeout = 4sec
Scan Timeout = 5sec
Scan Timeout = 6sec
Scan Timeout = 7sec
Scan Timeout = 8sec
Scan Timeout = 9sec
Scan Timeout = 10sec
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.6
Minimum Barcode Length
Minimum Length = 2
Minimum Length = 3
Minimum Length = 4
Minimum Length = 5
Minimum Length = 6
Minimum Length = 7
Minimum Length = 8
Minimum Length = 9
Minimum Length = 10
Minimum Length = 11
Minimum Length = 12
Minimum Length = 13
Minimum Length = 14
Minimum Length = 15
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Minimum Length = 16
Minimum Length = 17
Minimum Length = 18
Minimum Length = 19
Minimum Length = 20
Minimum Length = 21
Minimum Length = 22
Minimum Length = 23
Minimum Length = 24
Minimum Length = 25
Minimum Length = 26
Minimum Length = 27
Minimum Length = 28
Minimum Length = 29
Minimum Length = 30
Minimum Length = 31
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Minimum Length = 32
Minimum Length = 33
Minimum Length = 34
Minimum Length = 35
Minimum Length = 36
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.7
ScanIfConnect
ScanIfConnect = Enable
ScanIfConnect = Disable
16.8
Data Process - Wedge/Store, Enter Key & Extend
Key
Wedge Only
Wedge & Store Always
Store Only
Save if Sent
Save if Not Sent
Enable Enter Key
Disable Enter Key
Enable Extend Key
Disable Extend Key
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.9
Data Process - Data Edit
Start Prefix Enter
Start Suffix Enter
Finish Prefix / Suffix Enter
Cancel Prefix / Suffix Enter
Delete Prefix
Delete Suffix
Display Prefix
Display Suffix
AIM ID None
AIM ID In Prefix
AIM ID In Suffix
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.10
Data Process – Data Format
Data format = Barcode only
Data format = Packet data
16.11
Data Process - Termination Character &
Duplicate Check
Termination Character = None
Termination Character = CR
Termination Character = LF
Termination Character = CR+LF
Termination Character = Tab
Enable Duplicate Check
Disable Duplicate Check
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.12
Bluetooth
Enable Bluetooth Power
Disable Bluetooth Power
Enter Pairing Mode
Connect To
Disconnect
Enable Auto Pairing
Disable Auto Pairing
Bluetooth Profile = SPP
Bluetooth Profile = MFi
Enable Auto Reconnect
Disable Auto Reconnect
Display BT Mac Address
Display BT FW Version
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.13
System
Memory Status
Reset Memory
Enable Auto Erase
Disable Auto Erase
Battery
Display Version
Serial Number
Enable Beep Sound
Disable Beep Sound
Enable Power On Beep
Disable Power On Beep
Enable Beep On Connect
Disable Beep On Connect
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Enable Beep On Scan
Disable Beep On Scan
Enable BeepOnMSCard
Disable BeepOnMSCard
Enable BeepOnICCard
Disable BeepOnICCard
Enable BeepOnNFCCard
Disable BeepOnNFCCard
High Beep Volume
Low Beep Volume
Enable Auto Menu Exit
Disable Auto Menu Exit
Enable Port Status
Disable Port Status
Display Format = Time & Battery
Display Format = Type & Time
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Display Format = Type & Battery
Display Format = Memory Status
Display Format = Barcode Only
Enable Menu Barcode
Disable Menu Barcode
Factory Default
KDC Reset
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.14
Sleep Timeout
Sleep Timeout = Disable
Sleep Timeout = 5sec
Sleep Timeout = 10sec
Sleep Timeout = 20sec
Sleep Timeout = 30sec
Sleep Timeout = 1min
Sleep Timeout = 2min
Sleep Timeout = 5min
Sleep Timeout = 10min
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.15
NFC
Enable NFC Power
Disable NFC Power
16.16
MSR
Enable MSR Power
Disable MSR Power
No Beep On Error
Beep On Error
Enable Use Track1
Disable Use Track1
Enable Use Track2
Disable Use Track2
Enable Use Track3
Disable Use Track3
K
KDC User Manual MULTIPLE SPECIAL BARCODES
Enable Null Check Track1
Disable Null Check Track1
Enable Null Check Track2
Disable Null Check Track2
Enable Null Check Track3
Disable Null Check Track3
Enable Attach SS/ES
Disable Attach SS/ES
MSR Card Type = ISO
MSR Card Type = Other 1
MSR Card Type = AAMVA
MSR Card Type = JIS 2
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.17
ICCR(IC CARD READER)
Enable ICCR Power
Disable ICCR Power
IFD Number
Config Number
16.18
Key Management
Stored Keys
Inject Keys
K
KDC User Manual MULTIPLE SPECIAL BARCODES
16.19
Multilanguage
English
Korean
Japanese
K
KDC User Manual MULTIPLE SPECIAL BARCODES
17. Appendix G – Multiple Special
Barcodes
This chapter explains how to make a multiple configuration barcode for the KDC to configure multiple
KDC settings by scanning one barcode. The KDC provides special barcodes that enable changes to the
KDC configuration; but, this current barcode changes only one configuration. New KDC firmware
VersionR_305 introduces a feature to enable the user to make one special barcode to change multiple
KDC configurations.
17.1
KDC20/100/250/270L/350L/410/411/415/470L/500L
z Barcode type Code128 is used to make a single special barcode and its format is as follows:
<FNC3><Barcode String>
Here, the <FNC3> is a Code 128 control character and the <Barcode String> is an ASCII string for each KDC
configuration.
z The multiple configuration Code128 barcode format is as follows and has a control character
and series of barcode strings.
<FNC3><Barcode String 1>;;;;; <Barcode String N>
Here, the <FNC3> is a Code 128 control character and the <Barcode String 1> and <Barcode String N> are an ASCII
string for each KDC configuration. The ‘;’ is a separator for each configuration’s barcode string. Please see user
manual for the <Barcode String> for KDC configuration.
z Example: Assume the user is changing the following configurations with one barcode.
¾ Change Wedge/Store to “Wedge Only” Î <FNC3>82000
¾ Change Termination Character to “None” Î <FNC3>88000
¾ Change Bluetooth “Auto PowerOff” to “Disabled” Î <FNC3>64010
<FNC3>82000;88000;64010
17.2
KDC30/270C/300/350C/420/421/425/450/470C/500C
z The following format is for a single configuration barcode format:
<SYN> M <CR> KDC <Barcode String>.
K
KDC User Manual MULTIPLE SPECIAL BARCODES
z <SYN> is a control character 0x16 in hex format.
z M is an ASCII character 0x4D in hex format.
z <CR> is a control character 0x0d in hex format.
z KDC is an ASCII string 0x4B 0x44 0x43 in hex format.
z <Barcode String> is an ASCII string for each configuration
z . is an ASCII string 0x2E in hex format that indicates the end of barcode.
z The multiple configuration barcode string uses a repeated barcode string of each
configuration in the following format:
<SYN>M<CR>KDC<Barcode String 1> ;;;;;; <Barcode String N> .
z <SYN> is a control character 0x16 in hex format.
z M is an ASCII character 0x4D in hex format.
z <CR> is a control character 0x0d in hex format.
z KDC is an ASCII string 0x4B 0x44 0x43 in hex format.
z <Barcode String1> and <Barcode String N> are an ASCII string for each configuration
z ; is a separator between each barcode strings.
z . is an ASCII string 0x2E in hex format that indicates the end of barcode.
z Example: Assume the user is changing the following configurations with one barcode.
¾ Change Wedge/Store to “Wedge Only”
Î
<SYN>M<CR>KDC82000.
¾ Change Termination Character to “None”
Î
<SYN>M<CR>KDC 88000.
¾ Change Bluetooth “Auto PowerOff” to “Disabled”
Î
<SYN>M<CR>KDC 64010.
<SYN>M<CR>KDC82000;88000;64010.
z Code 128
z QR code
K
KDC User Manual MULTIPLE SPECIAL BARCODES
18. Appendix H – Product Specification
18.1
KDC470
Main Processor 120MHz ARM Cortex-M4
Memory 1MB for Firmware, 128KB for RAM, 8MB for User Data
Display N/A
Keypad 2 Scan Keys and Up/Down Key
Battery Li-ion 1130mh
Charging Micro USB or Charging Cradle
Mag-Stripe Reader N/A
Smart Card Reader N/A
Contactless and NFC
(NXP PN512)
N/A
Security N/A
Encryption N/A
Key Management N/A
Key Injection N/A
OS compatibility iOS, Android, Windows10
Barcode Scanner Supports 1D and 2D
Interfaces Bluetooth (V2.1+EDR, Class 2, HID/SPP/MFi), Micro USB port
Dimensions 65(W) x 1105(L) x 15.8(H) mm (2.56” x 4.13” x0.62”)
Weight 87g (3.07)
Drop Spec 5 feet(1.5M)
Operating Temperature 32˚F (0˚C) ~ 122˚F (50˚C)
Storage Temperature -4˚F (-20˚C) ~ 140˚F (60˚C)
Humidity 5% ~ 95% (noncondensing)