AMPAK Technology WMDA612ANTX Wireless Home Digital Interface Transmitter Dongle User Manual FCC WMDA 612ANx
AMPAK Technology Inc. Wireless Home Digital Interface Transmitter Dongle FCC WMDA 612ANx
Contents
- 1. User Man_ZQ6-WMDA612ANRX
- 2. User Man_ZQ6-WMDA612ANTX
User Man_ZQ6-WMDA612ANTX
WMAD-612AN Wireless HDMI Dongle Quick Installation Guide/ User Manual WDMA-612AN User Manual About this product Purpose The purpose of this document is to provide installation information for Wireless HDMI dongle products. Intended audience This document is for individuals who install Wireless HDMI dongle. How to use this document Use this guide to install Wirless HDMI dongle. Safety information WARNING: The following information lists the safety reminders for installation and maintenance personnel. Read all instructions before attempting to unpack, install, operate, or connect power to this product. Please remember the following when you unpack and install this equipment: • • • • • • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill any form of liquid on or into this product. Do not insert any sharp object into the products module openings or empty slots. Doing so may accidentally damage its parts. Do not attach the power supply cable on building surfaces or floorings. Rest the power cable freely without any obstacle or heavy items piled on top of it. Refrain from abusing, stepping or walking on the cable. To protect the equipment from overheating, do not block the slots and openings in the module housing that provide ventilation. Electrostatic discharge (ESD) can permanently damage semiconductor devices. Always follow ESD-prevention guidelines for equipment handling and storage. WDMA-612AN User Manual Eco-environmental statements The statements that follow are the eco-environmental statements that apply to WMDA-612AN Wireless HDMI dongle. Packaging collection and recovery requirements Countries, states, localities, or other jurisdictions may require that systems be established for the return and/or collection of packaging waste from the consumer, or other end user, or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the return and/or collection of the packaging waste may be established. For more information regarding collection and recovery of packaging and packaging waste within specific jurisdictions, please contact the Sonic Devices Technologies Field Services / Installation - Environmental Health and Safety organization. 1. Safety Guidelines In order to reduce the risk of fire, electric shock and injury, please adhere to the following safety guidelines. Carefully follow the instructions in this manual; also follow all instruction labels on this device. Only use the power adapter supplied with the device. Do not spill liquid of any kind on this device. Do not place the unit on an unstable stand or table; the unit may drop and become damaged. Do not expose this unit to direct sunlight. Do not place any hot devices close to this unit, as it may degrade or cause damage to it. Do not place any heavy objects on top of this unit. Do not use liquid cleaners or aerosol cleaners. Use a soft dry cloth for cleaning. WDMA-612AN User Manual 2. Packaging This package consists of the following items: WDMA-612AN_RX WMDA-612AN_TX WDMA-612AN User Manual AC Adapter Vin =230V 50Hz Vout =12V; 1A HDMI cables *2 WDMA-612AN User Manual 3. Structure WMDA-612AN_RX 1.Power Switch On/Off 2.Power Input 3.Reset Button 4.HDMI Output Port WMDA-612AN_TX 1.Power Switch On/Off 2.Power Input 3.Reset Button 4.HDMI Input Port WDMA-612AN User Manual 4. Installation and Use WMDA-612AN_RX Step.1 Plug in power. Step.2 Plug into Television HDMI input. WDMA-612AN User Manual WMDA-612AN_TX Step.3 Plug in power. Step.4 Plug in Video source.(ex. DVD/BD player, Game console, Set-Top Box or any source with HDMI output.) WDMA-612AN User Manual 5. Specifications WMDA-612AN_RX Product Name Wireless Home Digital Interface Receiver Dongle Model Number Host Interface WMDA-612_RX HDMI type A socket x1 for output to TV/Display MCU- ST/ STM32F103 HDMI- SiI9134 Chipset solution BBP- Amimon/AMN2220 RF- Amimon/AMN3210 DFS- AIROHA/ AL7230 (Option) Memory 4Mbit Flash 512Mb DDRII Switch Reset Button x 1, Power ON/OFF Button x 1, Red Power off Blue Power on Red Wireless unconnected Blue Wireless connected Red&Blue blink Search signal Power LED Wireless Dimensions PCBA 160.0L x 80.0W x 15.0H (mm) Operating Voltage 12V +/- 5% Power Consumption 6.6 Watt Total 6 PCB printed antenna ; Peak Gain:3.5 dBi Antenna 1 antenna for Transmitter & Receiver 4 antennas for Receiver 1 antenna for DFS Only (Option) Transmit Power (E.I.R.P.) Channel Bandwidth Modulation Uplink Data Rate 17.5 dBm (max.) 20MHz / 40MHz Downlink: OFDM 16-QAM Uplink: OOK User-defined downlink channel with up to 1 Mbps for data and control User-defined uplink channel with up to 100 Kbps for data and control WDMA-612AN User Manual Network mode Less than 1mSec latency between video source and video sink Uni-cast / Broad cast (Option) Low-end DFS without additional RF Chain DFS Support High-end DFS with additional RF Chain allowing to monitor additional DFS channel and immediate switch in case of radar detection Video resolutions HD: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p PC: VGA (640x480), SVGA (800x600), XGA (1024x768), Panel: 854x800, 1280x768, 1366x768, 1920x1080 3D video: 1280x720 @ 48Hz / 60Hz, 1920x1080 @ 48Hz / 60Hz) 3D gaming: 1280x720 @ 100Hz / 120Hz Audio Up to 18 Mbps audio stream: Operating Range Temperature Range I2S: Up to eight PCM channels (sampled up to 192 KHz x 24 bit). SPDIF: Including AC-3, DTS, Dolby 5.1, Digital 33~50 feet Indoor. The transmission quality varies in the system board and surrounding environment. 0 ~ 40°C (Operating), -20~60°C (Storage) WMDA-612AN_TX Product Name Wireless Home Digital Interface Transmitter Dongle Model Number Host Interface WMDA-612AN_TX HDMI type A socket x1 for input from HDMI/DVI source MCU- ST/STM32F105 Chipset solution HDMI- SiI9233 BBP- Amimon/AMN2120 RF- Amimon/AMN3110 Memory 4Mbit Flash Switch Reset Button x 1, Power ON/OFF Button x 1 Red Power off Blue Power on Red Wireless unconnected Blue Wireless connected Red&Blue blink Search signal Power LED Wireless Dimensions PCBA 160.0L x 105.0W x 15.0H (mm) Operating Voltage 12V +/- 5% Power 7.92 Watt Consumption Antenna Total 5 PCB printed antenna; Peak Gain: 3.5 dBi WDMA-612AN User Manual 4 antenna for Transmitter 1 antenna for Receiver Transmit Power 19.5 dBm (max.) (E.I.R.P.) Channel Bandwidth 20MHz / 40MHz Downlink: OFDM 16-QAM Modulation Uplink: OOK Downlink Data Rate User-defined downlink channel with up to 1 Mbps for data and control User-defined uplink channel with up to 100 Kbps for data and control Less than 1mSec latency between video source and video sink Network mode Uni-cast / Broad cast (Option) Video resolutions HD: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p PC: VGA (640x480), SVGA (800x600), XGA (1024x768) Panel: 854x800, 1280x768, 1366x768, 1920x1080 3D video: 1280x720 @ 48Hz / 60Hz, 1920x1080 @ 48Hz / 60Hz) Audio Operating Range Temperature Range 3D gaming: 1280x720 @ 100Hz / 120Hz’ -- I2S: Up to 8 PCM channels (sampled up to 192 KHz x 24 bit) -- Optional audio down-sampling for efficient modem bandwidth control SPDIF: Including AC-3, DTS 33~50 feet Indoor. The transmission quality varies in the system board and surrounding environment. 0 ~ 40°C (Operating), -20~60°C (Storage) 10 WDMA-612AN User Manual 7. Troubleshooting No Image Displayed on screen: Are the TX and RX units plugged in and on? Is the correct INP being used (press the button and test it) Is the TV on the correct input for the RX unit? (cycle between TV inputs) Is the "Link" light illuminated (carefully reset if not) Unit will not Link: There is a finite range for the device, and it varies depending on interference. Move the TX and RX units closer together, turn the units off, wait 25 sec, then power them back on. This should get the link. No Power light: Make certain the TX and RX units are plugged in as shown in the diagram. Check your power strip or wall socket to make sure there is power, do other devices power in that socket or on that power strip? Turn off and turn on the power. Make sure the switch is fully depressed. 11 WDMA-612AN User Manual 8. FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. 12 WDMA-612AN User Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 13
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res XMP Toolkit : 3.1-701 Create Date : 2011:09:16 17:32:27Z Creator Tool : PScript5.dll Version 5.2 Modify Date : 2011:09:16 18:04:24+08:00 Metadata Date : 2011:09:16 18:04:24+08:00 Format : application/pdf Creator : nicole.chao Title : Microsoft Word - User Manual_FCC_WMDA-612AN.docx Producer : GPL Ghostscript 8.15 Document ID : uuid:6b838f48-f683-4cec-bbd9-7028cd11148a Instance ID : uuid:9fdcdecf-7dde-4a2b-9dd2-62332909794c Page Count : 14 Author : nicole.chaoEXIF Metadata provided by EXIF.tools