AMX HST Bluetooth Handset User Manual MXA HST Modero X Series Bluetooth Handset

AMX LLC Bluetooth Handset MXA HST Modero X Series Bluetooth Handset

User manual

Installation GuideMXA-HST Modero X® Series Bluetooth HandsetOverviewThe MXA-HST Modero X Series Bluetooth Handset (FG5968-17) is an optional accessory for use with the Modero X series of touch panels. The handset allows wireless Bluetooth audio communication via the touch panel, while the handset’s Charging Cradle allows recharging either via a USB connection to the touch panel or via the included electrical adapter. Product Specifications Safety and Battery Charging InformationSafety Information• Do not dismantle, open, or shred the battery.• Do not short-circuit the battery. Do not store batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by conduc-tive materials.• Do not remove a battery from its original packaging until required for use.• Do not expose batteries to heat or fire. Avoid storage in direct sunlight.• Do not subject the batteries to mechanical shock.• In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.• Equipment should be designed to prohibit the incorrect insertion of the battery and its connector.• Store the batteries in a dry place with the temperature between 32° F (0° C) and 104° F (40° C).• Do not maintain the battery on charge when not in use.• Secondary batteries give their best performance when they are operated at normal room temperature: 68° F +/- 5° (20° +/- 5° C).CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.Charging• Use only with approved charger.• Charge with a constant-voltage, constant-current battery charger circuit with the following parameters:Maximum charge voltage 4.20 +/- 0.025 VDCMaximum charge current: 640 mACharge temperature range: 32° to 104° F (0° C to 40° C)Disposal• When disposing of batteries, keep cells or batteries of different electrochemical systems separate from each other.•Recycle or dispose of this battery in accordance with local regulations.FCC NoticeThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.Indicator Light StatusThe indicator light on the back of the MXA-HST (FIG. 1) flashes and changes color based on the handset’s current status.Getting StartedTo use your MXA-HST Bluetooth handset:1. Ensure that your handset is fully charged.2. Pair your charged handset with a Modero X Series touch panel. For more information, please refer to the Pairing the MXA-HST with a Modero X Series Touch Panel section on page 2 below.FIG. 1 MXA-HST HandsetMXA-HST SpecificationsPower Requirements: TBDBluetooth Specification: V2.1+EDR Class 2Bluetooth ProRes Supported: Headset Handsfree, A2DP and AVRCPRange of Frequency: 2.4GHz SpectrumNominal Charging Time: Within 3 hoursTalk Time: Up to 5 hoursStandby Time: Up to 130 hoursDimensions (HWD): • Handset: 6.88” x 1.62” x .77” (17.46 cm x 4.12 cm x 1.95 cm)• Charging Station: 1.93” x 3.64” 3.01” (5.06 cm x 9.25 cm x 7.65 cm)Weight: • Handset: 0.2 lbs (90.72 g)• Charging Cradle: 0.2 lbs (90.72 g)Certifications: • CE• FCC part 15 Class AIncluded Accessories: • Power plug, US (FGXXXX)Other AMX Equipment: • International power plug adapters, 3-pack (FGXXXX)Back FrontIndicator LightMulti-FunctionButtonMute ButtonVolumeUp/VolumeDown ButtonsIndicator LightHandset Status Indicator LightStandby Flash whiteCharging (OFF MODE) Solid blueFully Charged (OFF MODE) Solid whiteMute Solid redLow Battery Flash red with beep every minuteOut of Charge Indicator light turns offOut of Range Solid blue for 5 seconds
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).6/12©2012 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.AMX reserves the right to alter specifications without notice at any time. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com 93-5968-17 REV: A Charging the MXA-HSTThe MXA-HST comes with a built-in rechargeable battery. Prior to using the handset for the first time, fully charging the battery is highly recommended.To charge your handset:1. If you wish to charge your MXA-HST via USB, insert the USB plug of the Charging Cradle (FIG. 2) into an available USB port on the Modero X Series touch panel.2. Insert the base of the handset into the Charging Cradle. The indicator light on the back of the handset will turn blue while the handset is charging and solid white when it is fully charged. The charging indicator will be delayed for a few seconds if the handset has not been used for a long time or the battery is drained.NOTE: Use only the supplied Charging Cradle and USB charging cable to charge the handset.WARNING: Do not use the handset while it is seated in the Charging Cradle.NOTE: Fully charging the handset may require up to three hours.Pairing the MXA-HST with a Modero X Series Touch PanelTo pair your handset with a Modero X Series touch panel:1. Ensure that your handset is off before starting.2. To activate the pairing mode, press and hold the handset’s Multi-Function Button (MFB)(FIG. 1) for 8 seconds. 3. From the touch panel’s Settings Pages, pair the device with the touch panel. For more information on pairing a Modero X Series touch panel with a Bluetooth device, please refer to the Modero X Series Programming Guide, available from www.amx.com.4. If the pairing cannot be completed within three minutes after the pairing mode has been activated, the indicator light on the back of the MXA-HST will flash red rapidly five times and then shut off. Repeat steps 1 through 3 to pair both devices again.Resetting the MXA-HST/Removing Its Pairing HistoryTo reset your MXA-HST handset or remove its Bluetooth pairing history: 1. While the handset is in OFF mode, hold the Volume button and seat the handset into the Charging Cradle. The indicator light will flash red twice.2. Release the Volume button.3. The indicator light will stay red again and the handset is reset.Using the MXA-HST with a Modero X Series Touch PanelFIG. 2 MXA-HST Charging Cradle (front)Using the MXA-HST with a Modero X Series Touch PanelFunction Button Audio Indicator LED IndicatorPower ON Press and hold MFB for 2 secondsShort beep through the earphone Flash white light 3 timesPower OFF Press and hold MFB for 2 secondsLong beep through the earphone Flash blue light 2 times and then turns offStandby/Wake Up N/A N/A Flash white light every 8 secondsCharging N/A N/A Solid blue lightFully Charged N/A N/A Solid white lightLow battery N/A Long beep through the earphone Flash red lightOut of battery N/A N/A All lights turn offOut of range N/A Long beep through the earphone Solid blue light for 5 secondsPairing Press and hold MFB for 8 secondsN/A Flash white and blue lights alternatelyIncoming Call N/A Ringtone through the earphone Blinking blue lightAnswer/End a call Press MFB once Two step-up tones for AnswerTwo step-down tones for Hang-upFlash white light every 8 secondsAdjust Volume Press VOL UP and VOL DOWN Short beep through the earphone N/ALast Number Redial Press MFB twice N/A N/AReject Incoming Call Hold VOL UP or VOL DOWN for 2 secondsShort beep N/AMute Press Mute button once Solid red light

Navigation menu