AMX MIOR2 Remote Control Transmitter User Manual MIO R2
AMX LLC Remote Control Transmitter MIO R2
AMX >
Contents
- 1. User Manual 1
- 2. Users Manual 2
User Manual 1
Operation/Reference Guide Mio R-2 Remote Control Device Control System Accessories Document ID: 041-004-2978 I n i t i a l R e l e a s e : / L a s t R e v is e d : 0 4 / 2 5 / 2 0 0 6 AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: • Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. • Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. • AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers. • Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. • AMX Software is warranted for a period of ninety (90) days. • Batteries and incandescent lamps are not covered under the warranty. This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer. All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. Software License and Warranty Agreement LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the AMX Software. The AMX Software consists of generally available programming and development software, product documentation, sample applications, tools and utilities, and miscellaneous technical information. Please refer to the README.TXT file on the compact disc or download for further information regarding the components of the AMX Software. The AMX Software is subject to restrictions on distribution described in this License Agreement. LICENSEE MAY NOT SUBLICENSE, RENT, OR LEASE THE AMX SOFTWARE. Licensee may not reverse engineer, decompile, or disassemble the AMX Software. INTELLECTUAL PROPERTY. The AMX Software is owned by AMX and is protected by United States copyright laws, patent laws, international treaty provisions, and/or state of Texas trade secret laws. Licensee may make copies of the AMX Software solely for backup or archival purposes. Licensee may not copy the written materials accompanying the AMX Software. TERMINATION. AMX RESERVES THE RIGHT, IN ITS SOLE DISCRETION, TO TERMINATE THIS LICENSE FOR ANY REASON AND UPON WRITTEN NOTICE TO LICENSEE. In the event that AMX terminates this License, the Licensee shall return or destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been returned or destroyed. PRE-RELEASE CODE. Portions of the AMX Software may, from time to time, as identified in the AMX Software, include PRE-RELEASE CODE and such code may not be at the level of performance, compatibility and functionality of the final code. The PRE-RELEASE CODE may not operate correctly and may be substantially modified prior to final release or certain features may not be generally released. AMX is not obligated to make or support any PRE-RELEASE CODE. ALL PRE-RELEASE CODE IS PROVIDED "AS IS" WITH NO WARRANTIES. LIMITED WARRANTY. AMX warrants that the AMX Software will perform substantially in accordance with the accompanying written materials for a period of ninety (90) days from the date of receipt. AMX DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE AMX SOFTWARE. THIS LIMITED WARRANTY GIVES LICENSEE SPECIFIC LEGAL RIGHTS. Any supplements or updates to the AMX SOFTWARE, including without limitation, any (if any) service packs or hot fixes provided to Licensee after the expiration of the ninety (90) day Limited Warranty period are not covered by any warranty or condition, express, implied or statutory. LICENSEE REMEDIES. AMX's entire liability and Licensee's exclusive remedy shall be repair or replacement of the AMX Software that does not meet AMX's Limited Warranty and which is returned to AMX. This Limited Warranty is void if failure of the AMX Software has resulted from accident, abuse, or misapplication. Any replacement AMX Software will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer. Outside the United States, these remedies may not available. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL AMX BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS AMX SOFTWARE, EVEN IF AMX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO LICENSEE. U.S. GOVERNMENT RESTRICTED RIGHTS. The AMX Software is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph ©(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.2277013 or subparagraphs ©(1) and (2) of the Commercial Computer Software Restricted Rights at 48 CFR 52.227-19, as applicable. SOFTWARE AND OTHER MATERIALS FROM AMX.COM MAY BE SUBJECT TO EXPORT CONTROL. The United States Export Control laws prohibit the export of certain technical data and software to certain territories. No software from this Site may be downloaded or exported (i) into (or to a national or resident of) Cuba, Iraq, Libya, North Korea, Iran, Syria, or any other country to which the United States has embargoed goods; or (ii) anyone on the United States Treasury Department's list of Specially Designated Nationals or the U.S. Commerce Department's Table of Deny Orders. AMX does not authorize the downloading or exporting of any software or technical data from this site to any jurisdiction prohibited by the United States Export Laws. This Agreement replaces and supersedes all previous AMX Software License Agreements and is governed by the laws of the State of Texas, and all disputes will be resolved in the courts in Collin County, Texas, USA. For any questions concerning this Agreement, or to contact AMX for any reason, please write: AMX Corporation, 3000 Research Drive, Richardson, TX 75082. Table of Contents Table of Contents Overview ....................................................................................................................1 The Mio R-2....................................................................................................................... 1 Touch And Tilt Sensor.............................................................................................................. 2 Specifications ........................................................................................................................... 3 FCC compliance................................................................................................................ 4 Mio R-2 Setup ............................................................................................................5 Installing Your Custom Buttons ......................................................................................... 5 Inserting Batteries into The Mio R-2.................................................................................. 5 Battery Low Indicator......................................................................................................... 6 Programming The Mio R-2 .......................................................................................7 Using Connector Ports on The Mio R-2 ............................................................................ 7 IR Code Matrix .................................................................................................................. 8 Configuration Mode ........................................................................................................... 9 IR Transmit Mode.............................................................................................................. 9 Timeout Adjustment .......................................................................................................... 9 Download Mode .............................................................................................................. 10 Debug Mode.................................................................................................................... 10 Battery Type .................................................................................................................... 10 LED Awake Brightness.................................................................................................... 10 LED Sleep Mode Brightness ........................................................................................... 10 Persistent Serial Commands........................................................................................... 11 Mio R-2 Table of Contents ii Mio R-2 Overview Overview The Mio R-2 The Mio R-2 remote provides custom control features, contained in an elegant handheld rechargeable device. The Mio R-2 controls 6 different device modes, supports 3 macro functions and is capable of executing 219 functions. The Mio R-2 can transmit in 38 KHz IR, 455 KHz IR, 418 RF (1-way) (FG147-418), 433 RF (1-way) (FG147-433), or 38 KHz and one of the RF frequencies. Selecting a source device sends a command to the master and runs predetermined events associated with that source. Selecting a macro will run predefined events, which might not be associated with sources listed, then return the device to its previous mode. You need KeypadBuilder to properly program this device. The application and documentation are available from www.amx.com. Mio R-2 Overview Power Transmission Mode Current Menu Battery Meter Custom Macro Buttons Custom Mode 39 40 38 44 42 45 41 43 10 11 Options 15 13 16 12 14 26 28 1 - Power 11 - Volume Up 2 - Guide 12 - Volume Down 3 - Exit 13 - Channel Up 4 - Menu 14 - Channel Down 5 - Information 15 - Last Viewed 6 - Move Up 16 - Mute 7 - Move Down 26 - Input 8 - Move Left 28 - Enter 9 - Move Right 38 - Stop 10 - Select 39 - Record Numeral Keypad FIG. 1 The Mio R-2 Device Touch And Tilt Sensor The Mio R-2 wakes up upon touching either the chrome side rails or pressing a button. When holding the remote and it times out, you can reawaken the device by tilting it. Errant jostling such as a bumped table will not wake the device unless you are holding it. Mio R-2 Overview Specifications The Mio R-2 device specifications are as follows: Mio R-2 (FG147-418/433) Specifications Battery 4 AAA Alkaline Batteries (5 hours battery life) Transmission Frequencies • AMX 38 KHz/455 KHz IR • 418 RF (1-way) (FG147-418) • 433 RF (1-way) (FG147-433) Transmission Range (distance) with Mio IR Receiver • 100 feet at 38KHz (IR) • 50 feet at 455KHz (IR) • 300 feet at 418 (RF) • 200 feet at 433 (RF) Transmission Range (angle) • 140 degrees (+/-70° from perpendicular) horizontally from an axis extending from the end of the remote. (IR) • 40 degrees (+/-20° from perpendicular) vertically from an axis extending from the end of the remote. (IR) Top Components • LED - blue backlit buttons indicate device is awake • Display (OLED) - 128 x 32 pixels, active area is 29.42mm x 7.98mm • Pushbuttons - the power button is red backlit; the rest are blue backlit buttons. 45 buttons; 9 custom buttons (3 macro and 6 device). Rear Component • Programming Port - 2.5 mm stereo female conductor jack • Battery Door • Rechargeable Battery Connection Dimensions (HWD) 9.50 x 2.00 x .74 (241.3 mm x 50.8 mm x 18.80 mm) Supported Languages: • Arabic • Japanese • English • Korean • French • Mandarin Chinese • German • Portuguese • Greek • Russian • Hebrew • Spanish • Hindi • Thai • Italian Weight • .45 lbs (20 g) without batteries • .55 lbs (25 g) with batteries Operating Environment: • Operating Temperature: 0° to 50° C (32° to 122° F) • Storage Temperature: -10° to 70° C (14° to 158° F) Other AMX Equipment • DB-9 extension cable (FG10-727) • Programming Cable - a 3 wire, 2.5 mm stereo jack (FG10-817) • Custom engraving (FG147-01) • Mio-RCC Kit (FG147-03K) • Mio-RCC Charging Base (FG147-02) • Mio-RBP Rechargeable Lithium Ion Battery (FG147-10) • AXR-RF 418 MHZ RF Receiver (FG782-418) • AXR-RF 433 MHZ RF Receiver (FG782-433) Mio R-2 Overview FCC compliance This device complies with Part 15 of the FCC rules. Subject to the following two conditions: 1. This device must not cause harmful interference and 2. This device must accept all interference, including interference that interferes with the operation of this device. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Mio R-2 Mio R-2 Setup Mio R-2 Setup Installing Your Custom Buttons 3. Flip and turn the Mio R-2 device so that the buttons are facing away from you and the device is upside down. 4. Holding the device in both hands, place your thumbs on the battery door and push up to slide the battery door free. 5. Unscrew the 6 screw points indicated in FIG. 2. 6 Screw Points Programming Jack FIG. 2 Internal Mio R-2 Components 6. Turn the unit over so the buttons are facing you. 7. Lift the top assembly away from the PCB. 8. If necessary, push out the standard buttons from the front of the top assembly. 9. Drop on your custom button pad and verify the alignment with the guide posts on the PCB. 10. Place the top assembly back down on the PCB and return the unit over, exposing the 6 screw points. 11. Tighten the 6 screw points. 12. Place the battery door back on the device, slide to lock it in place. Inserting Batteries into The Mio R-2 To install your 4 AAA batteries into the Mio R-2 device: 1. Flip and turn the Mio R-2 device so that the buttons are facing away from you and the device is upside down. 2. Holding the device in both hands, place your thumbs on the battery door and slide the battery door free. 3. Insert the batteries as indicated inside the battery compartment. 4. Place the battery door back on the device, slide to lock it in place. Mio R-2 Mio R-2 Setup Battery Low Indicator When the battery charge level is too low to sustain continuous operation, the LCD flashes, "Battery Low" and the device shuts down. Mio R-2 Programming The Mio R-2 Programming The Mio R-2 Most functionality of the Mio R-2 is handled using the application, KeypadBuilder. Go to www.amx.com for the KeypadBuilder Instruction Manual. There are a select number of Serial Commands the Mio R-2 recognizes. For a full list and descriptions, consult the Persistent Serial Commands section on page 11. Using Connector Ports on The Mio R-2 The programming jack is used for communication between the device and KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you can order the programming cable (FG10-817) from AMX if you do not currently possess one. While loading your configuration file make sure the device is situated as such that the batteries will not fall out. The load will fail if your batteries fall out during the process. To download KeypadBuilder Configuration Files: 1. Set the Mio R-2 Download mode to ON. See the Configuration Mode section for details. 2. Flip and turn the Mio R-2 device so that the buttons are facing away from you and the device is upside down. 3. Holding the device in both hands, place your thumbs on the battery door and slide the battery door free. 4. Connect the 2.5 mm stereo plug (male) end of the programming cable (FG10-817) into the programming jack on the bottom side of the remote device. 5. If necessary, connect the DB-9 end of the programming cable to the female DB-9 connector on the DB-9 extension cable (FG10-727). 6. Connect the female DB-9 terminal end of the extension cable to the port on the back of your computer. 7. Configure the communication parameters in KeypadBuilder. Programming jack Mio R-2 DB-9 connector Stereo plug male Keypad device to PC programming cable Cable FG10-817 to cable FG10-727 FIG. 3 Connecting The Keypad Device to Your PC Mio R-2 Programming The Mio R-2 IR Code Matrix The IR Code emitted depends upon which of the 6 configurable modes is selected. Below is the list of codes for each button within each mode. IR Code Matrix Button Label Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Power Symbol 49 89 129 169 209 GUIDE 38 78 118 158 198 238 EXIT 37 77 117 157 197 237 MENU 31 71 111 151 191 231 INFO 39 79 119 159 199 239 32 72 112 152 192 232 33 73 113 153 193 233 34 74 114 154 194 234 35 75 115 155 195 235 10 SELECT 36 76 116 156 196 236 11 VOL + 24 64 104 144 184 224 12 VOL - 25 65 105 145 185 225 13 CH + 22 62 102 142 182 222 14 CH - 23 63 103 143 183 223 15 LAST 40 80 120 160 200 240 16 MUTE 26 66 106 146 186 226 17 11 51 91 131 171 211 18 12 52 92 132 172 212 19 13 53 93 133 173 213 20 14 54 94 134 174 214 21 15 55 95 135 175 215 22 16 56 96 136 176 216 23 17 57 97 137 177 217 24 18 58 98 138 178 218 25 19 59 99 139 179 219 26 INPUT 29 69 109 149 189 229 27 10 50 90 130 170 210 28 ENTER 21 61 101 141 181 221 29 A (Macro 1) 250 250 250 250 250 250 30 B (Macro 2) 251 251 251 251 251 251 31 C (Macro 3) 252 252 252 252 252 252 32 TV (Mode 1) 241 241 241 241 241 241 33 SAT (Mode 2) 242 242 242 242 242 242 34 DVD (Mode 3) 243 243 243 243 243 243 35 CD (Mode 4) 244 244 244 244 244 244 36 AUX (Mode 5) 245 245 245 245 245 245 37 LGHT (Mode 6) 246 246 246 246 246 246 38 STOP B 42 82 122 162 202 39 REC J 48 88 128 168 208 40 PAUSE C 43 83 123 163 203 Mio R-2 Programming The Mio R-2 IR Code Matrix (Cont.) Button Label 41 S. REV Z Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 47 87 127 167 207 42 PLAY A 41 81 121 161 201 43 S. FWD Y 46 86 126 166 206 44 REW E 45 85 125 165 205 45 FWD D 44 84 124 164 204 Configuration Mode The configuration mode allows you to set the following device features: IR Transmit Mode (38 KHz, 455 KHz or both 38 KHz IR and RF) Timeout Adjustment Download Mode Debug Mode Battery Type LED Awake Brightness LED Sleep Brightness To enter configuration Mode: 1. Press and hold the STOP button and the INPUT button. The two buttons must be pressed within 0.1 seconds of each other and held down for 2 seconds. The device indicates you are now in configuration mode. See below for available modes. 2. Press the EXIT key when you are finished. Your settings will not be lost in the event your batteries die or are removed. IR Transmit Mode Pressing button "1" on the remote toggles the IR transmission mode between 38KHz, 455KHz, RF, and both 38KHz IR and RF. The display indicates the current mode. Timeout Adjustment Press button "2" on the remote to change the sleep timeout from the default. Each time "2" is pressed, the sleep timeout raises incrementally. The pre-determined sleep timeouts are: 3 seconds 6 seconds 9 seconds 12 seconds The display indicates the selected sleep timeout. Mio R-2 Programming The Mio R-2 Download Mode Pressing "3" on the remote toggles the Download mode OFF and ON. The Download mode must be ON before you can download a file to the Mio R-2 device. While the Download mode is ON the device will not go to sleep. A power cycle will return the device to Download OFF. Debug Mode Pressing button "4" on the remote toggles development mode between ON and OFF. The display indicates the selected mode. In development mode, the display shows the IR code assigned to buttons when pressed. This mode is useful to the programmer when determining what IR codes are associated to each mode. Battery Type Pressing button "6" on the remote toggles the battery type between Normal and Recharge. The display indicates the selected type. The type of battery in the Mio R-2 dictates the battery type you need to set. LED Awake Brightness Pressing button "7" on the remote toggles the Power LED brightness mode from LOW to MED and then HIGH. The display indicates the selected mode. LED Sleep Mode Brightness Pressing button "8" on the remote toggles the Sleep brightness mode from OFF to LOW and then MED. The Sleep brightness is the state the Mio R-2 assumes while in the charging cradle. 10 Mio R-2 Programming The Mio R-2 Persistent Serial Commands There are a select number of persistent commands the Mio R-2 recognizes. Establish a HyperTerminal session with your device to use the following commands: Serial Commands @BRT Set Brightness level Syntax: "'BRIT-, '" Variables: brightness level # = a value from 0 - 32. "'@BRT-#'" (Set LED Awake brightness level) "'@BRT-#,#'" (Set LED Awake brightness level, sleep brightness level) Example: (1) "'@BRT-16'" Sets the awake brightness level to 50%. (2) "'@BRT-32,5'" Sets the awake brightness level to 100% and sleep brightness level to approximately 15% IRMODE # Sets the IR transmission frequency to either 455KHz or 38KHz. Syntax: "IRMODE #" Variables: # = 455 or 38 Example: "IRMODE 455" Sets the IR transmission frequency to 455KHz. SLEEP-# Force the device into screen saver mode. Syntax: "'SLEEP-#'" (timed sleep; a persistent command) Variables: # = 0 - 60 in seconds; time to wait before going to sleep. Default is 30. 0 sets the device to never sleep. Example: SEND_COMMAND Panel,"'SLEEP-45'" Forces the device into screen saver mode after 45 seconds. Mio R-2 11 ARGENTINA • AUSTRALIA • BELGIUM • BRAZIL • CANADA • CHINA • ENGLAND • FRANCE • GERMANY • GREECE • HONG KONG • INDIA • INDONESIA • ITALY • JAPAN LEBANON • MALAYSIA • MEXICO • NETHERLANDS • NEW ZEALAND • PHILIPPINES • PORTUGAL • RUSSIA • SINGAPORE • SPAIN • SWITZERLAND • THAILAND • TURKEY • USA ATLANTA • BOSTON • CHICAGO • CLEVELAND • DALLAS • DENVER • INDIANAPOLIS • LOS ANGELES • MINNEAPOLIS • PHILADELPHIA • PHOENIX • PORTLAND • SPOKANE • TAMPA 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com Last Revision: 4/25/06 041-004-2978 4/06 ©2006 AMX Corporation. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation. In Canada doing business as Panja Inc. AMX reserves the right to alter specifications without notice at any time.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : FrameMaker 7.2 Modify Date : 2006:05:04 14:10:25-05:00 Create Date : 2006:05:04 14:07:59Z Metadata Date : 2006:05:04 14:10:25-05:00 Format : application/pdf Title : MIO-R2.book Creator : Bperkins Document ID : uuid:63b58322-de13-445b-b928-0135a0439a62 Instance ID : uuid:cf934138-c2df-4d22-9ec3-fcc115772003 Has XFA : No Page Count : 18 Page Layout : SinglePage Author : BperkinsEXIF Metadata provided by EXIF.tools