ARESON Technology DL0004 Wireless Bluetooth Laser Mouse User Manual L219BT manual01

ARESON Technology Corp. Wireless Bluetooth Laser Mouse L219BT manual01

User manual

Battery use reminders1. Remove worn-out batteries from equipment immediately and dispose of promptly.2. Keep all batteries (used or new) out of the reach of children.3. To have the batteries with a regular check and replace new batteries if not used for a long time.4. Never dispose of batteries in fire, as they could explode.5. Always replace all the batteries at the same time. Mixing old and new batteries or mining types (such as alkaline with zinc carbon) will reduce overall performance and could cause leakage or rupture.6. Do not mix different types of batteries (e.g. Ni-MH, NiCd, alkaline, and etc) in the mouse.7. Remove batteries from the electrical device if the device is not going to be used for a long time.8. If the performance of the batteries decreases substantially, it is time to replace the batteries.User's GuideLaser Mouse L213BTFCC statementThis equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example-use only shielded interface cables when connecting to computer or peripheral devices).This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference. and (2) This device must accept any interference received, including interference that may cause undesired operation.This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end its life separately from your household waste. There are sparate collection system for recycling in the EU.For more information, please contact the local authority or your retailer where you purchased the product.Hereby, Areson Technology Corp., declares that this L213BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
PCIntroduction na htiW .esuom htooteulb evitavonni tsom eht fo esahcrup ruoy no snoitalutargnoCincredible sensitivity to surface details and high tracking speed than other mice, the mouse can track reliably even on tricky polished or wood-grain surfaces. It offers even more advance that will make you more productive and more comfortable.FeaturesThis product complies with IEC 60825-1, Class I laser product. (for Laser mouse models only.)The product complies with FCC and CE rules.Safety NoticeNote1. Insert the batteriesa. Remove the battery compartment cover on the bottom case of the mouseb. Fit in the batteries accordingly to the diagram indicated in the battery cabinet.c. Close the battery compartments cover properly.d. Make sure the Power on-off swich on the bottom of the mouse is ON.e. The Low Power LED on the wheel bar will blink 3 seconds if the mouse power is on. Hardware InstallationThe unit offers a strong power saving management. Once the mouse accesses the sleeping mode, " to click any button of the mouse" is compulsory to wake it up.Power on/off: Power on/off switch is designed to save the batteries power while non-usage of a longer period.2. Bluetooth Pairinga. Turn on your PC .b. Insert battery properly ( please refer to ”Hardware Installation” & ”Insert the batteries” ) make sure that mouse is in power on status. Push ID Button to enter connecting status, and low power LED will be flashing slowly Please DO NOT direct the laser beam at anyone's eyes.Wheel buttonDpi buttonID reset buttonMousePower on/off switchBattery coverLow power indicator+-A wrong battery placementmay cause batteries overheat.Battery compartment cover2 * AAA batteriesID reset buttonPower on/off switchThe red LED on the scroll bar of the mouse is a low batteries power indicator. It indicates that batteries inside the mouse need to be replaced.Make sure that you are not working the mouse on glossy or reflective surfaces.Internet Forward &Backward button2.4GHz Bluetooth RF (distance : 10m, in open site)Using state-of-art technology. High tracking speed and sensitivity.79 Channels.Power on/off switch.2*AAA Alkaline batteries included.800/1600 dpi switchable button.This Product doesn’t include Bluetooth dongle.The mouse easily connects to notebooks built in Bluetooth technology.The mouse also can be connected to Bluetooth dongle through your Bluetooth dongle driver, it is not guaranteed 100% compatile.
PCh.Now Bluetooth device is in connecting status.e. Please tick “ My device is set up and ready to found ” and click “ Next ”f. Choose “ Bluetooth Mouse New Device” and click “Next ”g. please tick “ Don’t use a passkey ” and click “ Next ” i. System will show installment finished in dialogue box, then click “ finish”.c. Click “Bluetooth icon” to open Bluetooth device in control panel or toolbar d..Click “ add “

Navigation menu