ARGtek Communication WIFI-011 802.11a/b/g/n 300Mbps AP Router User Manual ARG 1220 Power King Space QIG

ARGtek Communication Inc. 802.11a/b/g/n 300Mbps AP Router ARG 1220 Power King Space QIG

User Manual


ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
ARGtek ARG-1220 WLAN Dual Band
AP Router
For 802.11a/b/g/n
POWER KING SPACE
Quick Installation Guide

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
Part I: External Installation Direction
Package Content
AP Router 1
DC 12V Power Adapter 1
Dual Band Antenna 1
PoE DC Injector 1
Paper QIG 1
Manual/QIG CD 1
AP Router Connection
Before installing the router, connect your PC to the internet through your
broadband service.(If there is any problem, contact your ISP.)Then proceed
through the following steps.
1. Turn off your PC(s), cable/(A)DSL modem and the router.
2. Adjust the antenna. Normally, upright is a good place to start.
3. Connect the PC(s) and each switch/hub on your local area network to the
LAN ports on the router.
4. Connect the ADSL/DSL/cable modem to the router WAN port.
5. Connect the power adapter between the power socket on the router and
an electrical outlet. The router will start to work automatically.
6. Turn on your PC(s) and the cable/(A)DSL modem.

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
The Front LED Indicator
AP Router configuration
The AP Router is delivered with the following factory default parameters on the
Ethernet LAN interfaces.
Default IP Address: 10.10.10.254
Default IP subnet mask: 255.255.255.0
Web login User Name: admin
Web login Password: admin
The device has four operation modes (Gateway/Bridge/WISP/AP Client).
The default IP addresses for the device are 10.10.10.254, so you need to
make sure the IP address of your PC is in the same subnet as the device, such

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
as 10.10.10.X.
It will take about 55 seconds to complete the boot up sequence after power on.
PoE DC Injector Configuration
POE means Power over Ethernet, usually used with Wireless Device.
You can use it to integrate the power and the Ethernet then connected with the
RJ45 cable.

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
With POE, you can bring the power and Ethernet with long distance as far as
the length of RJ45 cable.
Since you used PoE DC Injector, the cable line won’t perplex you anymore.
Your Access Point & Router are installed conveniently to gain more efficient
bandwidth by yourself.
Less space and electricity limitation, more comfortable wireless life.
Part II: Internal Web Management
AP Mode Setup (ADSL)
1、 Install the antenna & power adapter, and then connect the LAN cable with
LAN port of this equipment. Another side of cable line connects with
network card of computer. Waiting for booting around 20 seconds.
2、 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to
enter the setup frame. If you can’t enter to setup frame, you can try to set
the IP address for 10.10.10.XXX and try to connect again. Otherwise,
please press Reset button around 10 seconds to restore AP and try to
enter again
Select the Operation Mode on the left side of setup frame
1. In Operation Mode, select Gateway and press Apply

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
2a. In Internet Settings / WAN /, select PPPoE (ADSL) for your WAN
Connection Type and enter your User Name & Password which were
presented by your ISOP company. And then press Apply
2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP
and etc. then press Apply

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
3. In Wireless Settings / Basic, you may change the setting of SSID, and then
press Apply
4. In Wireless Settings / Security, you may change the setting of password,
and then press Apply

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
Finish setting and press Apply, the setting will be completed after rebooting
around 20 seconds.
Note: You have to connect ADSL cable with the WAN port of this equipment.
==========================================================

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
AP Mode Setup (IP Share)
1、 Install the antenna & power adapter, and then connect the LAN cable with
LAN port of this equipment. Another side of cable line connects with RJ-45
of computer. Waiting for booting around 20 seconds.
2、 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to
enter the setup frame. If you can’t enter to setup frame, you can try to set
the IP address for 10.10.10.XXX and try to connect again. Otherwise,
please press Reset button around 10 seconds to restore AP and try to
enter again
Select the Operation Mode on the left side of setup frame
1. In Operation Mode, please select Bridge. Select AP or Main AP in Wireless
Operation Mode and press Apply

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
2 In Internet Setting/LAN/, you may change the setting of IP address, DHCP
and etc. then press Apply
3 In Wireless Settings / Basic, you may change the setting of SSID, and then
press Apply

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
4. In Wireless Settings / Security, you may change the setting of password,
and then press Apply

ARGtekCommunicationInc.www.argtek.com
E‐Mail:sales@argtek.comTel:+886‐2‐2999‐6958        Fax:+886‐2‐2999‐7742
Finish setting and press Apply, the setting will be completed after rebooting
around 20 seconds.
Note: You have to connect cable line with the LAN port of this equipment.
==========================================================
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Note: The country code selection is for non-US model only and is not
available to all US model. Per FCC regulation, all WiFi product marketed in
US must fixed to US operation channels only.

Navigation menu